MC100H604FNR2G [ONSEMI]
HEX TTL TO ECL TRANSLATOR, COMPLEMENTARY OUTPUT, PQCC28, LEAD FREE, PLASTIC, LCC-28;
| 型号： | MC100H604FNR2G |
| 厂家： | 
ONSEMI |
| 描述： | HEX TTL TO ECL TRANSLATOR, COMPLEMENTARY OUTPUT, PQCC28, LEAD FREE, PLASTIC, LCC-28 输出元件 接口集成电路 锁存器 |
| 文件： | 总6页 (文件大小：131K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MC10H604, MC100H604
Registered Hex TTL to ECL
Translator
Description
The MC10H/100H604 is a 6−bit, registered, dual supply TTL to
ECL translator. The device features differential ECL outputs as well as
a choice between either a differential ECL clock input or a TTL clock
input. The asynchronous master reset control is an ECL level input.
With its differential ECL outputs and TTL inputs the H604 device is
ideally suited for the transmit function of a HPPI bus type
board−to−boardinterface application. The on−chip registers simplify
the task of synchronizing the data between the two boards.
The device is available in either ECL standard: the 10H device is
compatible with MECL 10KH logic levels while the 100H device is
compatible with 100K logic levels.
http://onsemi.com
28
1
PLCC−28
FN SUFFIX
CASE 776
Features
• Differential 50 W ECL Outputs
• Choice Between Differential ECL or TTL Clock Input
• Dual Power Supply
MARKING DIAGRAM*
• Multiple Power and Ground Pins to Minimize Noise
• Specified Within−Device Skew
• Pb−Free Packages are Available*
1 28
MCxxxH604G
AWLYYWW
xxx
= 10 or 100
A
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
WL
YY
WW
G
*For additional marking information, refer to
Application Note AND8002/D.
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 4 of this data sheet.
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
© Semiconductor Components Industries, LLC, 2009
1
Publication Order Number:
September, 2009 − Rev. 6
MC10H604/D
MC10H604, MC100H604
D1 D2
V
CCT
D3 D4 D5 V
CCE
Table 1. PIN DESCRIPTION
25
24
23
22
21
20
19
PIN
FUNCTION
26
27
28
18
Q5
D0
D0−D5
CLK, CLK
TCLK
TTL Data Inputs
Differential ECL Clock Input
TTL Clock Input
17
16
TCLK
Q5
Q4
Q4
V
V
BB
MR
ECL Master Reset Input
True ECL Outputs
Q0−Q5
Q0−Q5
CLK
CLK
MR
15
14
13
12
Inverted ECL Outputs
2
3
4
CCE
V
CCE
V
CCT
V
EE
ECL V (0 V) = TTL GND
CC
TTL V (+5.0 V)
CC
Q3
Q3
ECL V (−5.2 V)
EE
V
CCE
5
6
7
8
9
10
11
Q0 Q0
V
EE
Q1 Q1 Q2 Q2
Figure 1. PLCC−28 Pinout (Top View)
Table 2. TRUTH TABLE
1 OF 6 BITS
D
MR
TCLK/CLK
Q +1
n
n
L
H
X
L
L
H
Z
Z
X
L
H
L
Qn
Qn
Dn
D
Q
Z = LOW to HIGH Transition
CLK
R
CLK
CLK
TCLK
*
MR
VBB
1. When using MECL inputs, TCLK must be tied to ground (0 V).
*
2. When using only one MECL input, the unused MECL input must be tied
to V , and TCLK must be tied to ground (0 V).
BB
3. When using TCLK, both MECL inputs must be tied to V (−5.2 V).
EE
Figure 2. Logic Symbol
Table 3. DC CHARACTERISTICS (V = V (Min) to V (Max); V
= GND; V
= 5.0 V +10%)
EE
EE
EE
CCE
CCT
0°C
25°C
85°C
Min
Max
Min
Max
Min
Max
Symbol
Parameter
ECL Power Supply Current
Unit
I
EE
10H
100H
130
130
130
140
130
150
mA
I
I
TTL Power Supply Current
35
45
35
45
35
45
mA
CCH
CCL
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
http://onsemi.com
2
MC10H604, MC100H604
Table 4. 10H ECL DC CHARACTERISTICS (V
= +5.0 V 10%; V = −5.20 V 5%; V
= GND)
CCT
EE
CCE
0°C
25°C
85°C
Min
Max
Min
Max
Min
Max
Symbol
Parameter
Condition
Unit
I
I
Input HIGH Current
Input LOW Current
255
175
175
mA
mA
INH
INL
0.5
0.5
0.5
V
IH
V
IL
Input HIGH Voltage
Input LOW Voltage
−1170
−1950
−840
−1480
−1130
−1950
−810
−1480
−1060
−1950
−720
−1480
mV
V
Output Bias Voltage
−1400
−1290
−1370
−1270
−1330
−1210
mV
mV
BB
V
OH
V
OL
Output HIGH Voltage
Output LOW Voltage
50 W to −2.0 V
−1020
−1950
−840
−1630
−980
−1950
−810
−1630
−910
−1950
−720
−1595
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
Table 5. 100H ECL DC CHARACTERISTICS (V
= 5.0 V 10%; V = −4.2 V to −5.5 V; V
= GND)
CCT
EE
CCE
0°C
25°C
85°C
Min
Max
Min
Max
Min
Max
Symbol
Parameter
Condition
Unit
I
I
Input HIGH Current
Input LOW Current
255
175
175
mA
mA
INH
INL
0.5
0.5
0.5
V
IH
V
IL
Input HIGH Voltage
Input LOW Voltage
−1165
−1810
−880
−1475
−1165
−1810
−880
−1475
−1165
−1810
−880
−1475
mV
V
Output Bias Voltage
−1400
−1280
−1400
−1280
−1400
−1280
mV
mV
BB
V
OH
V
OL
Output HIGH Voltage
Output LOW Voltage
50 W to −2.0 V
−1025
−1810
−880
−1620
−1025
−1810
−880
−1620
−1025
−1810
−880
−1620
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
Table 6. TTL DC CHARACTERISTICS (V
= 5.0 V 10%; V = −5.2 V 5% (10H); V = −4.2 V to −5.5 V (100H);
EE EE
CCT
V
CCE
= GND)
0°C
25°C
85°C
Min
Max
Min
Max
Min
Max
Symbol
Parameter
Condition
Unit
V
IH
V
IL
Input HIGH Voltage
Input LOW Voltage
2.0
2.0
2.0
V
V
0.8
0.8
0.8
I
IH
Input HIGH Current
V
IN
V
IN
= 2.7 V
= 7.0 V
20
100
20
100
20
100
mA
I
Input LOW Current
Input Clamp Voltage
V
= 0.5 V
−0.6
−1.2
−0.6
−1.2
−0.6
−1.2
mA
V
IL
IN
V
I
= −18 mA
IK
IN
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
http://onsemi.com
3
MC10H604, MC100H604
Table 7. AC CHARACTERISTICS (V
= 5.0 V 10%; V = −5.2 V 5% (10H); V = −4.2 V to −5.5 V (100H); V
= GND)
CCT
EE
EE
CCE
0°C
25°C
85°C
Min Typ Max Min Typ Max Min Typ Max
Symbol
Parameter
Condition
Unit
t
t
Propagation Delay
to Output
CLK to Q
TCLK to Q
MR to Q
50 W to −2.0 V
1.5
2.0
1.5
3.5
4.0
4.0
1.5
2.0
1.5
3.5
4.0
4.0
1.5
2.0
1.5
3.5
4.0
4.0
ns
PLH
PHL
t
t
t
Setup Time
50 W to −2.0 V
50 W to −2.0 V
50 W to −2.0 V
1.5
1.5
0.5
0.5
1.5
1.5
0.5
0.5
1.5
1.5
0.5
0.5
ns
ns
ns
s
Hold Time
H
Minimum Pulse Width
PW
CLK, MR
1.0
1.0
1.0
V
Minimum Input Swing
Rise/Fall Times
150
mV
ns
PP
t
r
t
f
20% − 80%
0.3
1.0
2.0
0.3
1.0
2.0
0.3
1.0
2.0
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
ORDERING INFORMATION
†
Device
Package
Shipping
MC10H604FN
PLCC−28
37 Units / Rail
37 Units / Rail
MC10H604FNG
PLCC−28
(Pb−Free)
MC10H604FNR2
PLCC−28
500 / Tape & Reel
500 / Tape & Reel
MC10H604FNR2G
PLCC−28
(Pb−Free)
MC100H604FN
PLCC−28
37 Units / Rail
37 Units / Rail
MC100H604FNG
PLCC−28
(Pb−Free)
MC100H604FNR2
MC100H604FNR2G
PLCC−28
500 / Tape & Reel
500 / Tape & Reel
PLCC−28
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
AN1406/D
AN1503/D
AN1504/D
AN1568/D
AN1672/D
AND8001/D
AND8002/D
AND8020/D
AND8066/D
AND8090/D
−
−
−
−
−
−
−
−
−
−
−
ECL Clock Distribution Techniques
Designing with PECL (ECL at +5.0 V)
ECLinPSt I/O SPiCE Modeling Kit
Metastability and the ECLinPS Family
Interfacing Between LVDS and ECL
The ECL Translator Guide
Odd Number Counters Design
Marking and Date Codes
Termination of ECL Logic Devices
Interfacing with ECLinPS
AC Characteristics of ECL Devices
http://onsemi.com
4
MC10H604, MC100H604
PACKAGE DIMENSIONS
28 LEAD PLLC
CASE 776−02
ISSUE F
M
S
S
N
0.007 (0.180)
T L-M
B
Y BRK
D
−N−
M
S
S
N
0.007 (0.180)
T L-M
U
Z
−M−
−L−
W
D
S
S
S
N
0.010 (0.250)
T L-M
X
G1
V
28
1
VIEW D−D
M
S
S
A
0.007 (0.180)
0.007 (0.180)
T L-M
T L-M
N
M
S
S
N
H
0.007 (0.180)
T L-M
Z
M
S
S
N
R
K1
C
E
0.004 (0.100)
K
G
SEATING
PLANE
−T−
J
M
S
S
N
0.007 (0.180)
T L-M
F
VIEW S
G1
VIEW S
S
S
S
N
0.010 (0.250)
T L-M
NOTES:
1. DATUMS -L-, -M-, AND -N- DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM -T-, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
INCHES
DIM MIN MAX
MILLIMETERS
MIN
12.32
12.32
4.20
MAX
12.57
12.57
4.57
A
B
C
E
F
0.485
0.485
0.165
0.090
0.013
0.495
0.495
0.180
0.110
0.021
2.29
0.33
2.79
0.53
G
H
J
0.050 BSC
1.27 BSC
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
0.026
0.020
0.025
0.450
0.450
0.042
0.042
0.042
---
0.032
---
---
0.66
0.51
0.64
11.43
11.43
1.07
1.07
1.07
---
0.81
---
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
K
R
U
V
W
X
Y
Z
---
0.456
0.456
0.048
0.048
0.056
0.020
10
11.58
11.58
1.21
1.21
1.42
0.50
10
2
2
_
_
_
_
G1 0.410
K1 0.040
0.430
---
10.42
1.02
10.92
---
http://onsemi.com
5
MC10H604, MC100H604
ECLinPS and MECL are trademarks of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
MC10H604/D
相关型号：
MC100H606FNG
IC HEX TTL/CMOS TO PECL TRANSLATOR, COMPLEMENTARY OUTPUT, PQCC28, LEAD FREE, PLASTIC, LCC-28, Level Translator
ONSEMI
MC100H606FNR2
HEX TTL/CMOS TO PECL TRANSLATOR, COMPLEMENTARY OUTPUT, PQCC28, PLASTIC, LCC-28
MOTOROLA
©2020 ICPDF网 联系我们和版权申明