MC10E195FNG [ONSEMI]
5V ECL Programmable Delay Chip; 5V ECL可编程延迟芯片型号: | MC10E195FNG |
厂家: | ONSEMI |
描述: | 5V ECL Programmable Delay Chip |
文件: | 总11页 (文件大小:151K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
MC10E195, MC100E195
5VꢀECL Programmable
Delay Chip
Description
The MC10E/100E195 is a programmable delay chip (PDC)
designed primarily for clock de-skewing and timing adjustment. It
provides variable delay of a differential ECL input transition.
The delay section consists of a chain of gates organized as shown in
the logic symbol. The first two delay elements feature gates that have
been modified to have delays 1.25 and 1.5 times the basic gate delay of
approximately 80 ps. These two elements provide the E195 with a
digitally-selectable resolution of approximately 20 ps. The required
device delay is selected by the seven address inputs D[0:6], which are
latched on chip by a high signal on the latch enable (LEN) control.
Because the delay programmability of the E195 is achieved by
purely differential ECL gate delays the device will operate at
frequencies of > 1.0 GHz while maintaining over 600 mV of output
swing.
http://onsemi.com
PLCC−28
FN SUFFIX
CASE 776
MARKING DIAGRAM*
1
MCxxxE195FNG
AWLYYWW
The E195 thus offers very fine resolution, at very high frequencies,
that is selectable entirely from a digital input allowing for very
accurate system clock timing.
An eighth latched input, D7, is provided for cascading multiple
PDC’s for increased programmable range. The cascade logic allows
full control of multiple PDC’s, at the expense of only a single added
line to the data bus for each additional PDC, without the need for any
external gating.
xxx
A
WL
YY
WW
G
= 10 or 100
= Assembly Location
= Wafer Lot
= Year
= Work Week
= Pb−Free Package
The V pin, an internally generated voltage supply, is available to
BB
this device only. For single-ended input conditions, the unused
*For additional marking information, refer to
Application Note AND8002/D.
differential input is connected to V as a switching reference voltage.
BB
V
BB
may also rebias AC coupled inputs. When used, decouple V
BB
and V via a 0.01 mF capacitor and limit current sourcing or sinking
CC
ORDERING INFORMATION
See detailed ordering and shipping information in the package
dimensions section on page 9 of this data sheet.
to 0.5 mA. When not used, V should be left open.
BB
The 100 Series contains temperature compensation.
Features
• 2.0 ns Worst Case Delay Range
• ≈20 ps/Delay Step Resolution
• >1.0 GHz Bandwidth
• On Chip Cascade Circuitry
• Meets or Exceeds JEDEC Spec EIA/JESD78 IC
Latchup Test
• Moisture Sensitivity Level: Pb = 1; Pb−Free = 3
For Additional Information, see Application Note
AND8003/D
• Flammability Rating: UL 94 V−0 @ 0.125 in,
Oxygen Index: 28 to 34
• Transistor Count = 368 devices
• PECL Mode Operating Range: V = 4.2 V to 5.7 V
CC
with V = 0 V
EE
• NECL Mode Operating Range: V = 0 V
CC
with V = −4.2 V to −5.7 V
EE
• Pb−Free Packages are Available*
• Internal Input 50 kW Pulldown Resistors
• ESD Protection: Human Body Model; > 2 kV,
Machine Model; > 200 V
*For additional information on our Pb−Free strategy and soldering details, please
download the ON Semiconductor Soldering and Mounting Techniques
Reference Manual, SOLDERRM/D.
©
Semiconductor Components Industries, LLC, 2006
1
Publication Order Number:
November, 2006 − Rev. 10
MC10E195/D
MC10E195, MC100E195
LOGIC DIAGRAM AND PINOUT ASSIGNMENT
Table 1. PIN DESCRIPTION
D2
D3
D4
D5
D6
D7
NC
PIN
FUNCTION
25
24
23
22
21
20
19
IN/IN
EN
ECL Signal Input
18
17
NC
NC
V
D1
D0
26
27
28
1
ECL Input Enable
D[0:7]
Q/Q
ECL MUX Select Inputs
ECL Signal Output
ECL Latch Enable
ECL Min Delay Set
ECL Max Delay Set
LEN
SET MIN
16
15
LEN
CC
SET MAX
CASCADE, CASCADE ECL Cascade Signal
V
V
CCO
EE
MC10E195
V
V
V
Reference Voltage Output
Positive Supply
Negative Supply
No Connect
BB
CC
EE
MC100E195
, V
CCO
IN
14
13
12
Q
Q
V
2
NC
IN
3
V
Table 2. TRUTH TABLE
4
BB
CCO
EN.
EN
L
H
L
Q = IN
Q Logic Low
5
6
7
8
9
10
11
NC
NC EN
LEN
Pass Through D[0:10]
Latch D[0:10]
LEN
H
L
*All V and V
pins are tied together on the die.
CCO
CC
SETMIN
SETMIN
SETMAX
SETMAX
Normal Mode
Warning: All V , V
connected to Power Supply to guarantee proper operation.
, and V pins must be externally
EE
CC CCO
H
L
Min Delay Path
Normal Mode
Figure 1. Pinout: 28-Lead PLCC
H
Max Delay Path
(Top View)
V
BB
1
0
0
0
0
0
0
0
IN
IN
4 GATES
8 GATES
16 GATES
1
1
1
1
1
1
1
1
1
1
0
Q
Q
EN
* 1.25
* 1.5
1
1
V
EE
CASCADE
LEN
LATCH
Q
LEN
7 BIT LATCH
SET MIN
SET MAX
D
CASCADE
CASCADE
D0
D1
D2
D3
D4
D5
D6
D7
* delays are 25% or 50% longer than
* standard (standard ≈ 80 ps)
Figure 2. Logic Diagram − Simplified
http://onsemi.com
2
MC10E195, MC100E195
Table 3. MAXIMUM RATINGS
Symbol
Parameter
Condition 1
= 0 V
Condition 2
Rating
Unit
V
V
V
V
PECL Mode Power Supply
NECL Mode Power Supply
V
V
8
CC
EE
I
EE
CC
= 0 V
−8
V
PECL Mode Input Voltage
NECL Mode Input Voltage
V
V
= 0 V
= 0 V
V v V
6
−6
V
V
EE
CC
I
CC
V w V
I
EE
I
I
Output Current
Continuous
Surge
50
100
mA
mA
out
V
Sink/Source
BB
± 0.5
mA
°C
BB
T
A
Operating Temperature Range
Storage Temperature Range
0 to +85
T
stg
−65 to +150
°C
q
Thermal Resistance (Junction−to−Ambient) 0 lfpm
500 lfpm
PLCC−28
PLCC−28
63.5
43.5
°C/W
°C/W
JA
q
Thermal Resistance (Junction−to−Case)
Standard Board
PLCC−28
22 to 26
°C/W
JC
V
PECL Operating Range
NECL Operating Range
4.2 to 5.7
−5.7 to −4.2
V
V
EE
T
sol
Wave Solder
Pb
Pb−Free
265
265
°C
Stresses exceeding Maximum Ratings may damage the device. Maximum Ratings are stress ratings only. Functional operation above the
Recommended Operating Conditions is not implied. Extended exposure to stresses above the Recommended Operating Conditions may affect
device reliability.
http://onsemi.com
3
MC10E195, MC100E195
Table 4. 10E SERIES PECL DC CHARACTERISTICS V
= 5.0 V; V = 0.0 V (Note 1)
EE
CCx
0°C
25°C
Typ
85°C
Typ
Min
Typ
Max
156
Min
Max
156
Min
Max
156
Symbol
Characteristic
Power Supply Current
Unit
mA
mV
mV
mV
mV
V
I
130
130
130
EE
V
V
V
V
V
V
Output HIGH Voltage (Note 2)
Output LOW Voltage (Note 2)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
3980 4070
3050 3210
3830 3995
3050 3285
3.62
4160
3370
4160
3520
3.74
4.6
4020
3050
3870
3050
3.65
2.2
4105
3210
4030
3285
4190
3370
4190
3520
3.75
4.6
4090
3050
3940
3050
3.69
2.2
4185
3227
4110
3302
4280
3405
4280
3555
3.81
4.6
OH
OL
IH
IL
BB
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 3)
2.2
V
IHCMR
I
I
Input HIGH Current
Input LOW Current
150
150
150
mA
mA
IH
IL
0.5
0.3
0.5
0.25
0.3
0.2
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
1. Input and output parameters vary 1:1 with V . V can vary −0.46 V / +0.06 V.
CC
EE
2. Outputs are terminated through a 50 W resistor to V − 2.0 V.
CC
3. V
min varies 1:1 with V , max varies 1:1 with V
.
IHCMR
EE
CC
Table 5. 10E SERIES NECL DC CHARACTERISTICS V
= 0.0 V; V = −5.0 V (Note 4)
EE
CCx
0°C
Typ
130
−1020 −930
25°C
Typ
85°C
Typ
Min
Max
156
Min
Max
156
Min
Max
156
Symbol
Characteristic
Power Supply Current
Unit
mA
mV
I
130
130
EE
V
V
V
V
V
V
Output HIGH Voltage (Note 5)
Output LOW Voltage (Note 5)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
−840
−980
−895
−810
−910
−815
−720
OH
OL
−1950 −1790 −1630 −1950 −1790 −1630 −1950 −1773 −1595 mV
−1170 −1005 −840 −1130 −970 −810 −1060 −890 −720 mV
−1950 −1715 −1480 −1950 −1715 −1480 −1950 −1698 −1445 mV
IH
IL
−1.38
−2.8
−1.27 −1.35
−1.25 −1.31
−1.19
−0.4
V
V
BB
Input HIGH Voltage Common Mode
Range (Differential Configuration) (Note 6)
−0.4
−2.8
−0.4
−2.8
IHCMR
I
I
Input HIGH Current
Input LOW Current
150
150
150
mA
mA
IH
IL
0.5
0.3
0.5
0.065
0.3
0.2
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
4. Input and output parameters vary 1:1 with V . V can vary −0.46 V / +0.06 V.
CC
EE
5. Outputs are terminated through a 50 W resistor to V − 2.0 V.
CC
6. V
min varies 1:1 with V , max varies 1:1 with V
.
IHCMR
EE
CC
http://onsemi.com
4
MC10E195, MC100E195
Table 6. 100E SERIES PECL DC CHARACTERISTICS V
= 5.0 V; V = 0.0 V (Note 7)
EE
CCx
0°C
25°C
Typ
130
85°C
Typ
150
Min
Typ
Max
Min
Max
Min
Max
Symbol
Characteristic
Power Supply Current
Unit
mA
mV
mV
mV
mV
V
I
130
156
156
179
EE
V
V
V
V
V
V
Output HIGH Voltage (Note 8)
Output LOW Voltage (Note 8)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
3975 4050 4120 3975 4050 4120 3975 4050 4120
3190 3295 3380 3190 3255 3380 3190 3260 3380
3835 3975 4120 3835 3975 4120 3835 3975 4120
3190 3355 3525 3190 3355 3525 3190 3355 3525
OH
OL
IH
IL
3.62
2.2
3.74
4.6
3.62
2.2
3.74
4.6
3.62
2.2
3.74
4.6
BB
Input HIGH Voltage Common Mode Range
(Differential Configuration) (Note 9)
V
IHCMR
I
I
Input HIGH Current
Input LOW Current
150
150
150
mA
mA
IH
IL
0.5
0.3
0.5
0.25
0.5
0.2
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
7. Input and output parameters vary 1:1 with V . V can vary −0.46 V / +0.8 V.
CC
EE
8. Outputs are terminated through a 50 W resistor to V − 2.0 V.
CC
9. V
min varies 1:1 with V , max varies 1:1 with V
.
IHCMR
EE
CC
Table 7. 100E SERIES NECL DC CHARACTERISTICS V
= 0.0 V; V = −5.0 V (Note 10)
CCx
EE
0°C
25°C
85°C
Typ
150
Min
Typ
Max
Min
Typ
Max
Min
Max
179
Symbol
Characteristic
Power Supply Current
Unit
mA
mV
I
130
156
130
156
EE
V
V
V
V
V
V
Output HIGH Voltage (Note 11)
Output LOW Voltage (Note 11)
Input HIGH Voltage (Single−Ended)
Input LOW Voltage (Single−Ended)
Output Voltage Reference
−1025 −950
−880 −1025 −950
−880 −1025 −950
−880
OH
OL
−1810 −1705 −1620 −1810 −1745 −1620 −1810 −1740 −1620 mV
−1165 −1025 −880 −1165 −1025 −880 −1165 −1025 −880 mV
−1810 −1645 −1475 −1810 −1645 −1475 −1810 −1645 −1475 mV
IH
IL
−1.38
−1.26 −1.38
−1.26 −1.38
−1.26
−0.4
V
V
BB
Input HIGH Voltage Common Mode Range −2.8
−0.4
−2.8
−0.4
−2.8
IHCMR
(Differential Configuration) (Note 12)
I
I
Input HIGH Current
150
150
150
mA
mA
IH
IL
Input LOW Current
0.5
0.3
0.5
0.25
0.5
0.2
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
10.Input and output parameters vary 1:1 with V . V can vary −0.46 V / +0.8 V.
CC
EE
11. Outputs are terminated through a 50 W resistor to V − 2.0 V.
CC
12.V
min varies 1:1 with V , max varies 1:1 with V
.
IHCMR
EE
CC
http://onsemi.com
5
MC10E195, MC100E195
Table 8. AC CHARACTERISTICS V
= 5.0 V; V = 0.0 V or V
= 0.0 V; V = −5.0 V (Note 13)
CCx EE
CCx
EE
0°C
25°C
Typ
85°C
Min
Typ
Max
Min
Max
Min
Typ
Max
Symbol
Characteristic
Unit
GHz
ps
f
Maximum Toggle Frequency
> 1.0
MAX
t
t
Propagation Delay
PLH
PHL
1210
3200
1250
300
1360
3570
1450
450
1510
3970
1650
700
1240
3270
1275
300
1390
3630
1475
450
1540
4030
1675
700
1440
3885
1350
300
1590
4270
1650
450
1765
4710
1950
700
IN to Q; Tap = 0
IN to Q; Tap = 127
EN to Q; Tap = 0
D7 to CASCADE
t
Programmable Range
(max) − t (min)
ps
ps
RANGE
2000
2175
2050
2240
2375
2580
t
PD
PD
Dt
Step Delay (Note 14)
17
34
17.5
35
21
42
D0 High
D1 High
D2 High
D3 High
D4 High
D5 High
D6 High
55
115
250
505
1000
68
105
180
325
620
1190
55
115
250
515
1030
70
105
180
65
140
305
620
1240
84
120
205
136
272
544
1088
140
280
560
1120
168
336
672
1344
325
380
620
1220
740
1450
L
Linearity (Note 15)
Duty Cycle Skew
D1
D0
D1
D0
D1
D0
in
t
ps
SKEW
±30
±30
±30
t
−t
(Note 16)
PHL PLH
t
t
Random Clock Jitter (RMS)
Setup Time
< 5
< 5
< 5
ps
ps
JITTER
s
200
800
200
0
200
800
200
0
200
800
200
0
D to LEN
D to IN (Note 17)
EN to IN (Note 18)
t
t
Hold Time
ps
ps
h
500
0
250
500
0
250
500
0
250
LEN to D
IN to EN (Note 19)
Release Time
R
300
800
800
300
800
800
300
800
800
EN to IN (Note 20)
SET MAX to LEN
SET MIN to LEN
t
Jitter
< 5
< 5
< 5
ps
ps
jit
t
t
Output Rise/Fall Time
r
f
125
300
225
450
325
650
125
300
225
450
325
650
125
300
225
450
325
650
20−80% (Q)
20−80% (CASCADE)
NOTE: Device will meet the specifications after thermal equilibrium has been established when mounted in a test socket or printed circuit
board with maintained transverse airflow greater than 500 lfpm. Electrical parameters are guaranteed only over the declared
operating temperature range. Functional operation of the device exceeding these conditions is not implied. Device specification limit
values are applied individually under normal operating conditions and not valid simultaneously.
13.10 Series: V can vary −0.46 V / +0.06 V.
EE
100 Series: V can vary −0.46 V / +0.8 V.
EE
14.Specification limits represent the amount of delay added with the assertion of each individual delay control pin. The various combinations
of asserted delay control inputs will typically realize D0 resolution steps across the specified programmable range.
15.The linearity specification guarantees to which delay control input the programmable steps will be monotonic (i.e. increasing delay steps for
increasing binary counts on the control inputsDn). Typically the device will be monotonic to the D0 input, however under worst case conditions
and process variation, delays could decrease slightly with increasing binary counts when the D0 input is the LSB. With the D1 input as the
Least Significant Bit (LSB), the device is guaranteed to be monotonic over all specified environmental conditions and process variation.
16.Duty cycle skew guaranteed only for differential operation measured from the cross point of the input to the cross point of the output.
17.This setup time defines the amount of time prior to the input signal the delay tap of the device must be set.
18.This setup time is the minimum time that EN must be asserted prior to the next transition of IN/IN to prevent an output response greater than
±75 mV to that IN/IN transition.
19.This hold time is the minimum time that EN must remain asserted after a negative going IN or positive going IN to prevent an output response
greater than ±75 mV to that IN/IN transition.
20.This release time is the minimum time that EN must be deasserted prior to the next IN/IN transition to ensure an output response that meets
the specified IN to Q propagation delay and transition times.
http://onsemi.com
6
MC10E195, MC100E195
ADDRESS BUS (A0−A6)
A7
D1
D1
D0
D0
E195
Chip #1
E195
Chip #2
V
V
CC
LEN
LEN
CC
V
V
CCO
Q
CCO
Q
V
V
EE
EE
IN
IN
IN
IN
INPUT
OUTPUT
Q
Q
V
V
CCO
CCO
V
V
BB
BB
Figure 3. Cascading Interconnect Architecture
Cascading Multiple E195’s
Chip #1 on the other hand will have both SET MIN and
SET MAX de-asserted so that its delay will be controlled
entirely by the address bus A0−A6. If the delay needed is
greater than can be achieved with 31.75 gate delays
(1111111 on the A0−A6 address bus) D7 will be asserted to
signal the need to cascade the delay to the next E195 device.
When D7 is asserted the SET MIN pin of chip #2 will be
de-asserted and the delay will be controlled by the A0−A6
address bus. Chip #1 on the other hand will have its SET
MAX pin asserted resulting in the device delay to be
independent of the A0−A6 address bus.
When the SET MAX pin of chip #1 is asserted the D0 and
D1 latches will be reset while the rest of the latches will be
set. In addition, to maintain monotonicity an additional gate
delay is selected in the cascade circuitry. As a result when D7
of chip #1 is asserted the delay increases from 31.75 gates
to 32 gates. A 32 gate delay is the maximum delay setting for
the E195.
To increase the programmable range of the E195 internal
cascade circuitry has been included. This circuitry allows for
the cascading of multiple E195’s without the need for any
external gating. Furthermore this capability requires only
one more address line per added E195. Obviously cascading
multiple PDC’s will result in a larger programmable range
however this increase is at the expense of a longer minimum
delay.
Figure 3 illustrates the interconnect scheme for cascading
two E195’s. As can be seen, this scheme can easily be
expanded for larger E195 chains. The D7 input of the E195
is the cascade control pin. With the interconnect scheme of
Figure 3 when D7 is asserted it signals the need for a larger
programmable range than is achievable with a single device.
An expansion of the latch section of the block diagram is
pictured below. Use of this diagram will simplify the
explanation of how the cascade circuitry works. When D7
of chip #1 above is low the cascade output will also be low
while the cascade bar output will be a logical high. In this
condition the SET MIN pin of chip #2 will be asserted and
thus all of the latches of chip #2 will be reset and the device
will be set at its minimum delay. Since the RESET and SET
inputs of the latches are overriding any changes on the
A0−A6 address bus will not affect the operation of chip #2.
To expand this cascading scheme to more devices one
simply needs to connect the D7 input and CASCADE
outputs of the current most significant E195 to the new most
significant E195 in the same manner as pictured in Figure 3.
The only addition to the logic is the increase of one line to
the address bus for cascade control of the second PDC.
TO SELECT MULTIPLEXERS
BIT 0
BIT 1
D1
BIT 2
BIT 3
D3
BIT 4
BIT 5
BIT 6
D6
BIT 7
D7
CASCADE
CASCADE
D0
Q0
Q1
D2
Q2
Q3
D4
Q4
D5
Q5
Q6
Q7
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
LEN
Reset Reset
SET MIN
SET MAX
Figure 4. Expansion of the Latch Section of the E195 Block Diagram
http://onsemi.com
7
MC10E195, MC100E195
30
1600
1575
Note:
All Taps Selected
SET = H, Temp. = 0°C
25
20
1550
1525
1500
15
10
5
1475
1450
1425
1400
1375
1350
1325
1300
0
−5
−10
−15
−5.5
−5.3
−5.1
−4.9
, (V)
−4.7
−4.5
−4.3
0
0
0
10
20
30 40 50 60
70
80 90 100
V
Temperature (°C)
EE
Figure 5. Change in Delay vs. Change in
Supply Voltage
Figure 6. Delay vs. Temperature (Fixed Path)
4400
4300
4200
4100
4000
3900
3800
3700
3600
2800
2000
1200
85°C
0°C
3600
3500
3400
0
10
20
30 40 50 60
70
80 90 100
32
64
96
128
Temperature (°C)
Tap Delay
Figure 7. Delay vs. Temperature (Max. Delay).
Figure 8. 100E195 Temperature Effects on
Delay.
3900
3400
2900
88
84
80
76
72
68
2400
1900
1400
64
0
10
20
30 40 50 60
70
80 90 100
20
40
60
80
100
120
Temperature (°C)
Tap Selection
Figure 9. Delay vs. Temperature (Per Gate).
Figure 10. E195 Delay Linearity.
http://onsemi.com
8
MC10E195, MC100E195
Z = 50 W
Q
Q
D
D
o
Receiver
Device
Driver
Device
Z = 50 W
o
50 W
50 W
V
TT
V
= V − 2.0 V
TT
CC
Figure 11. Typical Termination for Output Driver and Device Evaluation
(See Application Note AND8020/D − Termination of ECL Logic Devices.)
ORDERING INFORMATION
†
Device
Package
Shipping
MC10E195FN
PLCC−28
37 Units / Rail
37 Units / Rail
MC10E195FNG
PLCC−28
(Pb−Free)
MC10E195FNR2
PLCC−28
500 / Tape & Reel
500 / Tape & Reel
MC10E195FNR2G
PLCC−28
(Pb−Free)
MC100E195FN
PLCC−28
37 Units / Rail
37 Units / Rail
MC100E195FNG
PLCC−28
(Pb−Free)
MC100E195FNR2
MC100E195FNR2G
PLCC−28
500 / Tape & Reel
500 / Tape & Reel
PLCC−28
(Pb−Free)
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
Resource Reference of Application Notes
AN1405/D
AN1406/D
AN1503/D
AN1504/D
AN1568/D
AN1672/D
AND8001/D
AND8002/D
AND8020/D
AND8066/D
AND8090/D
−
−
−
−
−
−
−
−
−
−
−
ECL Clock Distribution Techniques
Designing with PECL (ECL at +5.0 V)
ECLinPSt I/O SPiCE Modeling Kit
Metastability and the ECLinPS Family
Interfacing Between LVDS and ECL
The ECL Translator Guide
Odd Number Counters Design
Marking and Date Codes
Termination of ECL Logic Devices
Interfacing with ECLinPS
AC Characteristics of ECL Devices
http://onsemi.com
9
MC10E195, MC100E195
PACKAGE DIMENSIONS
PLCC−28
FN SUFFIX
PLASTIC PLCC PACKAGE
CASE 776−02
ISSUE E
M
S
S
0.007 (0.180)
T
L−M
N
B
Y BRK
D
−N−
M
S
S
N
0.007 (0.180)
T
L−M
U
Z
−M−
−L−
W
D
S
S
S
N
0.010 (0.250)
T
L−M
X
G1
V
28
1
VIEW D−D
M
S
S
S
A
0.007 (0.180)
0.007 (0.180)
T
L−M
L−M
N
M
S
S
N
0.007 (0.180)
T
L−M
H
Z
M
S
T
N
R
K1
C
E
0.004 (0.100)
G
K
SEATING
PLANE
−T−
J
M
S
S
N
0.007 (0.180)
T
L−M
F
VIEW S
G1
S
S
S
N
0.010 (0.250)
T
L−M
VIEW S
NOTES:
INCHES
MILLIMETERS
1. DATUMS −L−, −M−, AND −N− DETERMINED
WHERE TOP OF LEAD SHOULDER EXITS
PLASTIC BODY AT MOLD PARTING LINE.
2. DIMENSION G1, TRUE POSITION TO BE
MEASURED AT DATUM −T−, SEATING PLANE.
3. DIMENSIONS R AND U DO NOT INCLUDE
MOLD FLASH. ALLOWABLE MOLD FLASH IS
0.010 (0.250) PER SIDE.
4. DIMENSIONING AND TOLERANCING PER
ANSI Y14.5M, 1982.
5. CONTROLLING DIMENSION: INCH.
6. THE PACKAGE TOP MAY BE SMALLER THAN
THE PACKAGE BOTTOM BY UP TO 0.012
(0.300). DIMENSIONS R AND U ARE
DETERMINED AT THE OUTERMOST
EXTREMES OF THE PLASTIC BODY
EXCLUSIVE OF MOLD FLASH, TIE BAR
BURRS, GATE BURRS AND INTERLEAD
FLASH, BUT INCLUDING ANY MISMATCH
BETWEEN THE TOP AND BOTTOM OF THE
PLASTIC BODY.
DIM MIN
MAX
0.495
0.495
0.180
0.110
0.019
MIN
12.32
12.32
4.20
MAX
12.57
12.57
4.57
A
B
C
E
F
0.485
0.485
0.165
0.090
0.013
2.29
0.33
2.79
0.48
G
H
J
0.050 BSC
1.27 BSC
0.026
0.020
0.025
0.450
0.450
0.042
0.042
0.042
0.032
−−−
−−−
0.66
0.51
0.64
11.43
11.43
1.07
1.07
1.07
−−−
0.81
−−−
K
R
U
V
W
X
Y
Z
−−−
0.456
0.456
0.048
0.048
0.056
11.58
11.58
1.21
1.21
1.42
0.50
10
−−− 0.020
10
2
2
_
_
_
_
G1 0.410
K1 0.040
0.430
−−−
10.42
1.02
10.92
−−−
7. DIMENSION H DOES NOT INCLUDE DAMBAR
PROTRUSION OR INTRUSION. THE DAMBAR
PROTRUSION(S) SHALL NOT CAUSE THE H
DIMENSION TO BE GREATER THAN 0.037
(0.940). THE DAMBAR INTRUSION(S) SHALL
NOT CAUSE THE H DIMENSION TO BE
SMALLER THAN 0.025 (0.635).
http://onsemi.com
10
MC10E195, MC100E195
ECLinPS is a trademark of Semiconductor Components Industries, LLC (SCILLC).
ON Semiconductor and
are registered trademarks of Semiconductor Components Industries, LLC (SCILLC). SCILLC reserves the right to make changes without further notice
to any products herein. SCILLC makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does SCILLC assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
“Typical” parameters which may be provided in SCILLC data sheets and/or specifications can and do vary in different applications and actual performance may vary over time. All
operating parameters, including “Typicals” must be validated for each customer application by customer’s technical experts. SCILLC does not convey any license under its patent rights
nor the rights of others. SCILLC products are not designed, intended, or authorized for use as components in systems intended for surgical implant into the body, or other applications
intended to support or sustain life, or for any other application in which the failure of the SCILLC product could create a situation where personal injury or death may occur. Should
Buyer purchase or use SCILLC products for any such unintended or unauthorized application, Buyer shall indemnify and hold SCILLC and its officers, employees, subsidiaries, affiliates,
and distributors harmless against all claims, costs, damages, and expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death
associated with such unintended or unauthorized use, even if such claim alleges that SCILLC was negligent regarding the design or manufacture of the part. SCILLC is an Equal
Opportunity/Affirmative Action Employer. This literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
N. American Technical Support: 800−282−9855 Toll Free
USA/Canada
Europe, Middle East and Africa Technical Support:
Phone: 421 33 790 2910
Japan Customer Focus Center
Phone: 81−3−5773−3850
ON Semiconductor Website: www.onsemi.com
Order Literature: http://www.onsemi.com/orderlit
Literature Distribution Center for ON Semiconductor
P.O. Box 5163, Denver, Colorado 80217 USA
Phone: 303−675−2175 or 800−344−3860 Toll Free USA/Canada
Fax: 303−675−2176 or 800−344−3867 Toll Free USA/Canada
Email: orderlit@onsemi.com
For additional information, please contact your local
Sales Representative
MC10E195/D
相关型号:
MC10E196FNR2
Active Delay Line, Programmable, 1-Func, 127-Tap, Complementary Output, ECL, PQCC28, PLASTIC, LCC-28
MOTOROLA
©2020 ICPDF网 联系我们和版权申明