NIS6420 [ONSEMI]
Electronic Fuse, 3 to 12 V;型号: | NIS6420 |
厂家: | ONSEMI |
描述: | Electronic Fuse, 3 to 12 V |
文件: | 总11页 (文件大小:164K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Electronic Fuse, 3 to 12 V
NIS6420
The NIS6420 is a cost effective, resettable fuse which can greatly
enhance the reliability of a hard drive or other circuit from both
catastrophic and shutdown failures.
It is designed to protect the downstream circuitry against an
overcurrent event by limiting the current while protecting against high
inrush current, as well as monitoring the load current in real time.
www.onsemi.com
Features
• 42 mW Typical
• Digital and Tristate Enable
• Integrated Reverse Current Protection
• Thermally Protected
WQFN12
CASE 510BM
• Integrated Soft−Start Circuit
• Internal Undervoltage Lockout Circuit
• Internal Charge Pump
MARKING DIAGRAM
• Load Current Monitor Pin
XXMG
• ESD Ratings:
G
Human Body Model (HBM); 2000 V
Charged Device Model (CDM); 2000 V
Latch−Up; Class 1
XX = Specific Device Code
M
G
= Date Code
= Pb−Free Package
• These Devices are Pb−Free and are RoHS Compliant
(Note: Microdot may be in either location)
Typical Applications
• Hard Drives
PIN CONNECTIONS
• Solid State Drives
• Mother Boards
• Industrial
• Handheld Devices
• Portable Instruments
12
1
2
3
4
5
V
V
V
V
V
V
11
10
IN
IN
IN
OUT
OUT
OUT
NIS6420
9
8
7
13
SAS
I
LIM
IN
dV/dt
En/Fault
6
ORDERING INFORMATION
See detailed ordering and shipping information on page 10 of
this data sheet.
© Semiconductor Components Industries, LLC, 2019
1
Publication Order Number:
December, 2020 − Rev. 4
NIS6420/D
NIS6420
3V to 12V
Source
VIN
VOUT
LOAD
22mF
NIS6420
SAS Disable
SASIN
ISENSE
1mF
RSENSE
1kW
ILIM
EN/Fault
Fault
EN
RLIM
GND
dV/dt
Cdvdt
Figure 1. Typical Application Circuit
3V to 12V
Source
VIN
VOUT
LOAD
22mF
NIS6420
SAS Disable
SASIN
ISENSE
ILIM
1mF
RSENSE
1kW
EN/Fault
Fault
EN
RLIM
GND
dV/dt
Cdvdt
11
10
9
+12 Source
Source
Source
Source
Vcc
8
7
Source
Source
6
3
Enable/
Fault
4
2
ILIMIT
RLIM
NIS5x2x
LOAD
dV/dt
GND
1
Figure 2. Common Thermal Shutdown with another eFuse
www.onsemi.com
2
NIS6420
V
IN
Charge
Pump
EN/Fault
Enable/Fault
SAS
Disable
SAS
IN
Current
Limit
Current
Monitor
I
SENSE
V
Thermal
Shutdown
OUT
I
Limit
dV/dt
dV/dt
Control
UVLO
GND
Figure 3. Block Diagram
www.onsemi.com
3
NIS6420
Table 1. PIN FUNCTION DESCRIPTION
Pin No.
Pin Name
Description
1,2,3
V
IN
Positive input voltage to the device. Connect a 22 mF or greater capacitor to ground.
4
5
SAS
When this pin is pulled high the eFuse is turned off.
IN
EN/Fault
This pin is a tri−state, bidirectional interface. It can be pulled to ground with an external open−drain
or open collector device to shut down the eFuse. It can also be used as a status indicator; if the
voltage level is intermediate (around 1.4 V), the eFuse is in thermal shutdown. If the voltage level is
high (around 3 V) the eFuse is operating normally. Do not actively drive this pin to any voltage. Do
not connect a capacitor to this pin.
6
7
I
Current Sense Pin. Connect a 1 kW 1% resistor and a 1 mF capacitor to ground.
The internal dV/dt circuit controls the slew rate of the output voltage at turn on.
A resistor between this pin and the source pin sets the overload and short circuit current limit levels.
Source of the internal power FET and the output terminal of the fuse
SENSE
dV/dt
8
I
LIM
9,10,11
12,13
V
OUT
GND
Negative input voltage to the device. This is used as the internal reference for the IC.
Table 2. MAXIMUM RATINGS
Rating
Symbol
Value
Unit
Input Voltage, operating, steady−state (V to GND)
V
IN
−0.3 to +16
−0.3 to +19
−0.3 to 6
V
IN
Transient (100 ms)
Voltage range on EN/Fault pin
V
Voltage range on SAS pin
−0.3 to 6
IN
Stresses exceeding those listed in the Maximum Ratings table may damage the device. If any of these limits are exceeded, device functionality
should not be assumed, damage may occur and reliability may be affected.
Table 3. THERMAL RATINGS
Thermal Resistance, Junction to Air
q
75
12
12
5
°C/W
°C/W
°C/W
°C/W
JA
2
(4 layer High−K JEDEC JESD51−7 PCB, 100 mm , 2 oz. Cu)
Thermal Resistance, Junction−to−Lead
(4 layer High−K JEDEC JESD51−7 PCB, 100 mm , 2 oz. Cu)
Y
J−L
J−B
J−T
max
2
Thermal Resistance, Junction−to−Board
(4 layer High−K JEDEC JESD51−7 PCB, 100 mm , 2 oz. Cu)
Y
Y
2
Thermal Resistance, Junction−to−Case Top
(4 layer High−K JEDEC JESD51−7 PCB, 100 mm , 2 oz. Cu)
2
Total Power Dissipation @ T = 25°C
P
A
2
(4 layer High−K JEDEC JESD51−7 PCB, 100 mm , 2 oz. Cu)
1.67
13.4
W
mW/°C
°C
Derate above 25°C
Operating Ambient Temperature Range
Operating Junction Temperature Range
Non−operating Storage Temperature Range
Lead Temperature, Soldering (10 Sec)
T
−40 to 125
−55 to 150
−55 to 155
260
A
T
°C
J
T
STG
°C
T
°C
L
www.onsemi.com
4
NIS6420
Table 4. ELECTRICAL CHARACTERISTICS
(Unless otherwise noted: V = 12 V, dV/dt pin open, R
= 10 kW, T = 25°C)
IN
LIM
A
Characteristics
POWER FET
Symbol
Min
Typ
Max
Unit
ON Resistance (Note 4)
T = 140°C (Note 5)
J
R
42
62
5
60
mW
A
DS(on)
Continuous Current (Ta = 25°C, 0.5 sq in pad) (Note 4)
(Ta = 80°C, minimum copper)
I
d
3.8
Off State Leakage (Vin = 12 V, EN = 0 V)
THERMAL LATCH
I
1
mA
leak
Shutdown Temperature (Note 1)
UNDERVOLTAGE PROTECTION
Undervoltage Lockout (Turn on, Voltage Going High)
UVLO Hysteresis
T
150
2.3
175
0.3
200
3.0
°C
SD
V
UVLO
V
V
V
Hyst
CURRENT LIMIT
Overload Current Limit (overload/trigger), R
= 10 kW
I
4.5
2.3
A
A
LIM
OL
Short Circuit Current Limit, R
= 10 kW
I
1.99
5.5
2.6
40
LIM
SC
Current Limit Response Time
LOAD CURRENT MONITORING
T
ms
ilim
Load Monitor Sense Current, R
REVERSE CURRENT LIMIT
Reverse Current Limit (Note 5)
= 1 kW
I
0.8
5
1
1.2
mA/A
SENSE
SENSE
I
1.78
10
A
REVERSE
Reverse Current Limit Response Time
(dVin/dt = −5 V/1 ms, 20 mF Load)
T
ms
IREVERSE
SLEW RATE CONTROL
Slew Rate (No dV/dt capacitor)
ENABLE/FAULT
SR
1.0
ms
Output Logic Level Low (Output Disabled)
EN
0.8
V
V
(VOL)
Output Logic Level Mid (Thermal Fault, Output Disabled)
Output Logic Level High (Output Enabled)
Logic Low Sink Current (Venable = 0 V)
EN
0.9
2.1
1.4
1.95
(O−MID)
EN
V
(VOH)
(ISink)
(ILeak)
EN
EN
16.7
20.24
1
mA
mA
Logic High Leakage Current for External Switch
(Venable = 3.3 V)
Maximum Fanout for Fault Signal (Total number of chips that
can be connected to this pin for simultaneous shutdown)
EN
3
Units
(Fanout)
SAS DISABLE
Logic Level Low (Output Enabled)
Logic Level High (Output Disabled)
De−glitch Filter Delay
TOTAL DEVICE
SAS
SAS
0.3
2
V
V
IN(VIL)
1.2
50
IN(VIH)
SAS
ms
Tdly
Bias Current
I
mA
Bias
Operational (I
= 0 A)
300
220
100
Load
Shutdown (EN = 0), (Note 2)
Fault
120
www.onsemi.com
5
NIS6420
Table 4. ELECTRICAL CHARACTERISTICS
(Unless otherwise noted: V = 12 V, dV/dt pin open, R
= 10 kW, T = 25°C)
IN
LIM
A
Characteristics
FAULT EVENTS
Symbol
Min
Typ
Max
Unit
EN/Fault
Level
V
OUT
State
Latch
Under Voltage Lock Out
Thermal Shutdown
UVLO
TSD
EN
EN
EN
off
off
off
on
no
(VOL)
(MID)
(MID)
(VOH)
yes, (Note 1)
no, (Note 5)
N/A
Reverse Current Protection
No Fault (Vin > UVLO)
Ireverse
EN
Product parametric performance is indicated in the Electrical Characteristics for the listed test conditions, unless otherwise noted. Product
performance may not be indicated by the Electrical Characteristics if operated under different conditions.
1. eFuse is latched off until the En/Fault pin is pulled low and then released, the SAS Disable pin is pulled high and then released or a power
on reset is applied to the device.
2. Does not include fan out of Enable/Fault function.
3. Pulse test: Pulse width 300 s, duty cycle 2%
4. Verified by design.
5. Once the device has entered shutdown mode due to a reverse current event, it will re−enable its output when V > V
for at least 100 ms.
IN
OUT
The slew rate SR will be applied when the output is re−enabled.
www.onsemi.com
6
NIS6420
TYPICAL CHARACTERISTICS
35
30
25
20
15
10
100
10
−40°C
25°C
85°C
5
0
1
0
200 400 600 800 1000 1200 1400 1600 1800 2000
0
5
10
POWER (W)
15
20
Capacitance from dV/dt Pin to GND (pF)
Figure 4. Slew Rate vs dV/dt Capacitance
3.3 V to 12 V VCC
Figure 5. Thermal Trip Time vs. Power
Dissipation
3.0
60
50
UVLO Rising
UVLO Falling
2.5
2.0
1.5
1.0
40
30
20
0.5
0
10
0
UVLO Hysteresis
−40
−20
0
20
40
60
80
100
−50 −30
−10
10
30
50
70
90 110
JUNCTION TEMPERATURE (°C)
JUNCTION TEMPERATURE (°C)
Figure 6. UVLO vs. Junction Temperature
Figure 7. RDS(on) vs. Junction Temperature
45
40
35
30
25
20
15
10
5
0
3
4
5
6
7
8
9
10 11 12 13 14 15 16
(V)
V
CC
Figure 8. RDS(on) vs. VCC
Figure 9. Slew Rate Control
www.onsemi.com
7
NIS6420
TYPICAL CHARACTERISTICS
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
0.5
0
0
0.5 1.0 1.5 2.0 2.5 3.0 3.5 4.0 4.5
LOAD CURRENT (A)
−40
−20
0
20
40
60
80
100
AMBIENT TEMPERATURE (°C)
Figure 10. VISENSE vs. Load Current
Figure 11. VISENSE vs. Ambient Temperature
4.0
3.5
3.0
2.5
2.0
1.5
1.0
10
I
@ R
= 5 kW
9
8
7
6
5
4
OL
LIM
I
@ R
@ R
= 5 kW
SC
LIM
I
OL
= 15 kW
LIM
LIM
3
I
OL
@ R
= 25 kW
2
1
0
I
I
@ R
@ R
= 15 kW
= 25 kW
SC
SC
LIM
LIM
0.5
0
3
4
5
6
7
8
9
10 11 12 13 14 15 16
(V)
−60 −40 −20
0
20
40
60
80 100
V
CC
AMBIENT TEMPERATURE (°C)
Figure 12. VISENSE vs. VCC
Figure 13. ILIM vs. RLIM over Ambient
Temperature
9
8
7
6
5
4
3
2
1
0
I
OL
I
SC
0
5
10
15
(kW)
20
25
30
R
LIM
Figure 14. Overload and Short Circuit Current
Limit vs RLIM
www.onsemi.com
8
NIS6420
APPLICATIONS INFORMATION
SAS Disable
Basic Operation
This device is a self−protected, resettable, electronic fuse.
It contains circuits to monitor the input voltage, output
voltage, output current and die temperature.
The SAS Disable feature provides a digital interface to
control the output of the eFuse. When the SAS pin is
IN
pulled high by any external digital control circuitry the
On application of the input voltage, the device will apply
the input voltage to the load based on the restrictions of the
controlling circuits. The output voltage, which is controlled
by an internal dv/dt circuit, will slew from 0 V to the rated
output voltage in 1.3 ms.
The device will remain on as long as the temperature does
not exceed the 175°C limit that is programmed into the chip.
The internal current limit circuit does not shut down the
part but will reduce the conductivity of the FET to maintain
a constant current at the internally set current limit level.
An internal charge pump provides bias for the gate voltage
of the internal n−channel power FET and also for the current
limit circuit. The remainder of the control circuitry operates
eFuse switches to its off state. When the SAS pin is pulled
low the eFuse output is turned on. All fault conditions will
be cleared when the eFuse is reset through the SAS pin.
IN
Reverse Current Protection
The NIS6420 monitors and protects against reverse
current events, which can be the result of a malfunction in
the power supply or noise induced in the input voltage rail
under certain load characteristics (for example, when the
load is largely capacitive).
The protection mechanism disables the eFuse’s output
and triggers when the reverse current exceeds the preset
magnitude and this condition remains for at least 7.5 ms.
The NIS6420 automatically re−enables its output once the
input voltage exceeds the output voltage for at least 100 ms.
between the input voltage (V ) and ground.
CC
Enable/Fault
Current Limit
The Enable/Fault Pin is a multi−function, bidirectional
pin that can control the output of the chip as well as send
information to other devices regarding the state of the chip.
When this pin is low, the output of the fuse will be turned off.
When this pin is high the output of the fuse will be
turned−on. If a thermal fault occurs, this pin will be pulled
low to an intermediate level by an internal circuit. To use as
a simple enable pin, an open drain or open collector device
should be connected to this pin. Due to its tri−state operation,
it should not be connected to any type of logic with an
internal pull−up device.
If the chip shuts down due to the die temperature reaching
its thermal limit, this pin will be pulled down to an
intermediate level. This signal can be monitored by an
external circuit to communicate that a thermal shutdown has
occurred. If this pin is tied to another device in this family,
a thermal shutdown of one device will cause both devices to
disable their outputs. Both devices will turn on once the fault
is removed for the auto−retry devices.
The current limit circuit uses a SENSEFET along with a
reference and amplifier to control the peak current in the
device. The SENSEFET allows for a small fraction of the load
current to be measured, which has the advantage of reducing
the losses in the sense resistor. The current limit circuit has two
limiting values, one for short circuit hold current − I , another
SC
is overload current limit I . Refer to Figure 14. for
OL
dependence of I and I vs current limit resistor R .
OL
SC
LIM
Load Current Monitoring
The current monitor I
pin provides a small current
SENSE
proportional to the main device current which is flowing
through the device. This pin should have a decoupling
capacitor to filter out internal sampling noise. A resistor
connected between the I
pin and GND converts the
SENSE
I
current into a GND referenced voltage. This pin can
SENSE
be floated if the feature is not required by application.
Connect this pin to ground through 1 kOhm 1% resistor and
a 1 mF capacitor to ground to read the voltage corresponding
to a load current.
Since this is a latching thermal device, the outputs will be
enabled after the enable pin has been pulled to ground with
an external switch and then allowed to go high or after the
input power has been recycled.
Slew Rate Control
The dV/dt circuit brings the output voltage up under a
linear, controlled rate regardless of the load impedance
characteristics. An internal ramp generator creates a linear
ramp, and a control circuit forces the output voltage to
follow that ramp, scaled by a factor. The default ramp time
is approximately 1.3 ms. This pin includes an internal
current source of approximately 1 mA. Since the current
level is very low, it is important to use a ceramic cap or other
low leakage capacitor. Aluminum electrolytic capacitors are
not recommended for this circuit. Refer to Figure 4. for the
typical ramp time vs Cdvdt capacitor. Anytime that the unit
shuts down due to a fault, enable shut−down, or recycling of
input power, the timing capacitor will be discharged and the
output voltage will ramp from 0 at turn on.
Thermal Protection
The NIS6420 includes an internal temperature sensing
circuit that senses the temperature on the die of the power
FET. If the temperature reaches 175°C, the device will shut
down, and remove power from the load. Output power can
be restored by either recycling the input power or toggling
the enable pin.
The thermal limit has been set high intentionally, to
increase the trip time during high power transient events. It
is not recommended to operate this device above 150°C for
extended periods of time.
www.onsemi.com
9
NIS6420
ORDERING INFORMATION
Device
†
Marking
62L
Auto−Retry/Latch
Latch
Package
Shipping
NIS6420MT1TWG
NIS6420MT2TWG
3000 / Tape & Reel
3000 / Tape & Reel
WQFN12
(Pb−Free)
62A
Auto−Retry
†For information on tape and reel specifications, including part orientation and tape sizes, please refer to our Tape and Reel Packaging
Specifications Brochure, BRD8011/D.
www.onsemi.com
10
NIS6420
PACKAGE DIMENSIONS
WQFN12 3.0x2.0, 0.5P
CASE 510BM
ISSUE C
ON Semiconductor and
are trademarks of Semiconductor Components Industries, LLC dba ON Semiconductor or its subsidiaries in the United States and/or other countries.
ON Semiconductor owns the rights to a number of patents, trademarks, copyrights, trade secrets, and other intellectual property. A listing of ON Semiconductor’s product/patent
coverage may be accessed at www.onsemi.com/site/pdf/Patent−Marking.pdf. ON Semiconductor reserves the right to make changes without further notice to any products herein.
ON Semiconductor makes no warranty, representation or guarantee regarding the suitability of its products for any particular purpose, nor does ON Semiconductor assume any liability
arising out of the application or use of any product or circuit, and specifically disclaims any and all liability, including without limitation special, consequential or incidental damages.
Buyer is responsible for its products and applications using ON Semiconductor products, including compliance with all laws, regulations and safety requirements or standards,
regardless of any support or applications information provided by ON Semiconductor. “Typical” parameters which may be provided in ON Semiconductor data sheets and/or
specifications can and do vary in different applications and actual performance may vary over time. All operating parameters, including “Typicals” must be validated for each customer
application by customer’s technical experts. ON Semiconductor does not convey any license under its patent rights nor the rights of others. ON Semiconductor products are not
designed, intended, or authorized for use as a critical component in life support systems or any FDA Class 3 medical devices or medical devices with a same or similar classification
in a foreign jurisdiction or any devices intended for implantation in the human body. Should Buyer purchase or use ON Semiconductor products for any such unintended or unauthorized
application, Buyer shall indemnify and hold ON Semiconductor and its officers, employees, subsidiaries, affiliates, and distributors harmless against all claims, costs, damages, and
expenses, and reasonable attorney fees arising out of, directly or indirectly, any claim of personal injury or death associated with such unintended or unauthorized use, even if such
claim alleges that ON Semiconductor was negligent regarding the design or manufacture of the part. ON Semiconductor is an Equal Opportunity/Affirmative Action Employer. This
literature is subject to all applicable copyright laws and is not for resale in any manner.
PUBLICATION ORDERING INFORMATION
LITERATURE FULFILLMENT:
Email Requests to: orderlit@onsemi.com
TECHNICAL SUPPORT
North American Technical Support:
Voice Mail: 1 800−282−9855 Toll Free USA/Canada
Phone: 011 421 33 790 2910
Europe, Middle East and Africa Technical Support:
Phone: 00421 33 790 2910
For additional information, please contact your local Sales Representative
ON Semiconductor Website: www.onsemi.com
◊
www.onsemi.com
相关型号:
©2020 ICPDF网 联系我们和版权申明