R1LV1616HSA-4LI
更新时间:2024-09-18 10:36:08
品牌:RENESAS
描述:Wide Temperature Range Version 16 M SRAM (1-Mword × 16-bit / 2-Mword × 8-bit)
R1LV1616HSA-4LI 概述
Wide Temperature Range Version 16 M SRAM (1-Mword × 16-bit / 2-Mword × 8-bit) 工作温度范围宽版16M的SRAM ( 1 - Mword × 16位/ 2 - Mword × 8位) SRAM
R1LV1616HSA-4LI 规格参数
是否Rohs认证: | 符合 | 生命周期: | Transferred |
零件包装代码: | TSOP1 | 包装说明: | TSSOP, TSSOP48,.8,20 |
针数: | 48 | Reach Compliance Code: | unknown |
ECCN代码: | 3A991.B.2.A | HTS代码: | 8542.32.00.41 |
风险等级: | 5.61 | Is Samacsys: | N |
最长访问时间: | 45 ns | 备用内存宽度: | 8 |
I/O 类型: | COMMON | JESD-30 代码: | R-PDSO-G48 |
长度: | 18.4 mm | 内存密度: | 16777216 bit |
内存集成电路类型: | STANDARD SRAM | 内存宽度: | 16 |
湿度敏感等级: | 2 | 功能数量: | 1 |
端子数量: | 48 | 字数: | 1048576 words |
字数代码: | 1000000 | 工作模式: | ASYNCHRONOUS |
最高工作温度: | 85 °C | 最低工作温度: | -40 °C |
组织: | 1MX16 | 输出特性: | 3-STATE |
封装主体材料: | PLASTIC/EPOXY | 封装代码: | TSSOP |
封装等效代码: | TSSOP48,.8,20 | 封装形状: | RECTANGULAR |
封装形式: | SMALL OUTLINE, THIN PROFILE, SHRINK PITCH | 并行/串行: | PARALLEL |
峰值回流温度(摄氏度): | 260 | 电源: | 3/3.3 V |
认证状态: | Not Qualified | 座面最大高度: | 1.2 mm |
最大待机电流: | 0.000025 A | 最小待机电流: | 1.5 V |
子类别: | SRAMs | 最大压摆率: | 0.05 mA |
最大供电电压 (Vsup): | 3.6 V | 最小供电电压 (Vsup): | 2.7 V |
标称供电电压 (Vsup): | 3 V | 表面贴装: | YES |
技术: | CMOS | 温度等级: | INDUSTRIAL |
端子形式: | GULL WING | 端子节距: | 0.5 mm |
端子位置: | DUAL | 处于峰值回流温度下的最长时间: | 20 |
宽度: | 12 mm | Base Number Matches: | 1 |
R1LV1616HSA-4LI 数据手册
通过下载R1LV1616HSA-4LI数据手册来全面了解它。这个PDF文档包含了所有必要的细节,如产品概述、功能特性、引脚定义、引脚排列图等信息。
PDF下载R1LV1616H-I Series
Wide Temperature Range Version
16 M SRAM (1-Mword × 16-bit / 2-Mword × 8-bit)
REJ03C0195-0101
Rev.1.01
Nov.18.2004
Description
The R1LV1616H-I Series is 16-Mbit static RAM organized 1-Mword × 16-bit / 2-Mword × 8-bit.
R1LV1616H-I Series has realized higher density, higher performance and low power consumption by
employing CMOS process technology (6-transistor memory cell). It offers low power standby power
dissipation; therefore, it is suitable for battery backup systems. It is packaged in 48-pin plastic TSOPI for
high density surface mounting.
Features
•
•
•
Single 3.0 V supply: 2.7 V to 3.6 V
Fast access time: 45/55 ns (max)
Power dissipation:
Active: 9 mW/MHz (typ)
Standby: 1.5 µW (typ)
•
Completely static memory.
No clock or timing strobe required
Equal access and cycle times
Common data input and output.
Three state output
•
•
•
Battery backup operation.
2 chip selection for battery backup
Temperature range: −40 to +85°C
Byte function (×8 mode) available by BYTE# & A-1.
•
•
Rev.1.01, Nov.18.2004, page 1 of 19
R1LV1616H-I Series
Ordering Information
Type No.
Access time
45 ns
Package
R1LV1616HSA-4LI
R1LV1616HSA-4SI
R1LV1616HSA-5SI
48-pin plastic TSOPI (48P3R-B)
45 ns
55 ns
Rev.1.01, Nov.18.2004, page 2 of 19
R1LV1616H-I Series
Pin Arrangement
48-pin TSOP
48
1
A16
A15
A14
A13
A12
A11
A10
A9
2
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
BYTE#
VSS
3
4
I/O15/A-1
I/O7
5
6
I/O14
I/O6
7
8
I/O13
I/O5
A8
9
A19
NC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
I/O12
I/O4
WE#
CS2
NU
VCC
I/O11
I/O3
UB#
LB#
A18
A17
A7
I/O10
I/O2
I/O9
I/O1
I/O8
A6
I/O0
A5
OE#
VSS
A4
A3
CS1#
A0
A2
A1
(Top view)
Rev.1.01, Nov.18.2004, page 3 of 19
R1LV1616H-I Series
Pin Description (TSOP)
Pin name
A0 to A19
A-1 to A19
I/O0 to I/O15
CS1# (CS1)
CS2
Function
Address input (word mode)
Address input (byte mode)
Data input/output
Chip select 1
Chip select 2
WE# (WE)
OE# (OE)
LB# (LB)
UB# (UB)
BYTE# (BYTE)
VCC
Write enable
Output enable
Lower byte select
Upper byte select
Byte enable
Power supply
VSS
Ground
NC
No connection
NU*1
Not used (test mode pin)
Note: 1. This pin should be connected to a ground (VSS), or not be connected (open).
Rev.1.01, Nov.18.2004, page 4 of 19
R1LV1616H-I Series
Block Diagram (TSOP)
LSB
A15
V CC
V SS
A14
A13
A12
A11
A10
A9
Memory matrix
8,192 x 128 x 16
•
•
•
•
•
Row
decoder
A8
8,192 x 256 x 8
A18
A16
A19
A4
A5
MSB
I/O0
•
•
•
•
Column I/O
Input
data
Column decoder
control
I/O15
MSB
LSB
A17A7A6 A3 A2 A0
A1 A-1
•
•
BYTE#
CS2
CS1#
LB#
Control logic
UB#
WE#
OE#
Rev.1.01, Nov.18.2004, page 5 of 19
R1LV1616H-I Series
Operation Table (TSOP)
Byte mode
CS1# CS2 WE# OE# UB# LB# BYTE# I/O0 to I/O7 I/O8 to I/O14 I/O15
Operation
Standby
Standby
Read
H
×
L
L
L
×
×
×
×
L
×
H
×
×
×
×
×
×
×
×
×
×
L
L
L
L
L
High-Z
High-Z
Dout
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
High-Z
A-1
L
×
H
H
H
H
L
Din
A-1
Write
H
High-Z
High-Z
Output disable
Note: H: VIH, L: VIL, ×: VIH or VIL
Word mode
CS1# CS2 WE# OE# UB# LB# BYTE# I/O0 to I/O7 I/O8 to I/O14 I/O15
Operation
Standby
H
×
×
L
L
L
L
L
L
L
×
×
×
×
×
L
L
L
×
×
×
H
×
×
H
L
H
L
L
H
L
×
×
×
H
L
L
H
L
L
H
×
H
H
H
H
H
H
H
H
H
H
High-Z
High-Z
High-Z
Dout
High-Z
High-Z
High-Z
Dout
High-Z
High-Z
High-Z
Dout
L
×
Standby
×
×
Standby
H
H
H
H
H
H
H
H
H
H
L
Read
Dout
High-Z
Dout
High-Z
Dout
Lower byte read
Upper byte read
Write
High-Z
Din
Din
Din
L
Din
High-Z
Din
High-Z
Din
Lower byte write
Upper byte write
Output disable
L
High-Z
High-Z
H
High-Z
High-Z
Note: H: VIH, L: VIL, ×: VIH or VIL
Rev.1.01, Nov.18.2004, page 6 of 19
R1LV1616H-I Series
Absolute Maximum Ratings
Parameter
Symbol
VCC
Value
Unit
V
Power supply voltage relative to VSS
Terminal voltage on any pin relative to VSS
Power dissipation
−0.5 to +4.6
−0.5*1 to VCC + 0.3*2
1.0
VT
V
PT
W
Storage temperature range
Storage temperature range under bias
Tstg
Tbias
−55 to +125
−40 to +85
°C
°C
Notes: 1. VT min: −2.0 V for pulse half-width ≤ 10 ns.
2. Maximum voltage is +4.6 V.
DC Operating Conditions
Parameter
Symbol Min
Typ
Max
3.6
0
Unit
Note
Supply voltage
VCC
VSS
VIH
VIL
2.7
0
3.0
0
V
V
Input high voltage
2.2
−0.3
−40
VCC + 0.3 V
Input low voltage
0.6
V
1
Ambient temperature range
Ta
+85
°C
Note: 1. VIL min: −2.0 V for pulse half-width ≤ 10 ns.
Rev.1.01, Nov.18.2004, page 7 of 19
R1LV1616H-I Series
DC Characteristics
Parameter
Symbol Min
Typ
Max Unit Test conditions*2
Input leakage current
Output leakage current
|ILI|
|ILO
1
1
µA
µA
Vin = VSS to VCC
|
CS1# = VIH or CS2 = VIL or
OE# = VIH or WE# = VIL or
LB# = UB# = VIH, VI/O = VSS to VCC
Operating current
ICC
20
mA CS1# = VIL, CS2 = VIH,
Others = VIH/ VIL, II/O = 0 mA
Average operating current
ICC1
(READ)
22*1 35
mA Min. cycle, duty = 100%,
II/O = 0 mA, CS1# = VIL, CS2 = VIH,
WE# = VIH, Others = VIH/VIL
ICC1
30*1 50
mA Min. cycle, duty = 100%,
I
I/O = 0 mA, CS1# = VIL, CS2 = VIH,
Others = VIH/VIL
3
ICC2
(READ)
*
3*1
8
mA Cycle time = 70 ns, duty = 100%,
II/O = 0 mA, CS1# = VIL, CS2 = VIH,
WE# = VIH, Others = VIH/VIL
Address increment scan or
decrement scan
3
ICC2
*
20*1 30
mA Cycle time = 70 ns, duty = 100%,
II/O = 0 mA, CS1# = VIL, CS2 = VIH,
Others = VIH/VIL
Address increment scan or
decrement scan
ICC3
3*1
8
mA Cycle time = 1 µs, duty = 100%,
II/O = 0 mA, CS1# ≤ 0.2 V,
CS2 ≥ VCC − 0.2 V
VIH ≥ VCC − 0.2 V, VIL ≤ 0.2 V
Standby current
ISB
0.1*1 0.5
0.5*1
mA CS2 = VIL
Standby current -4SI
-5SI
ISB1
8
µA
µA
0 V ≤ Vin
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS1# ≥ VCC − 0.2 V,
CS2 ≥ VCC − 0.2 V or
(3) LB# = UB# ≥ VCC − 0.2 V,
CS2 ≥ VCC − 0.2 V,
CS1# ≤ 0.2 V
-4LI
ISB1
0.5*1 25
Average value
Output high voltage
Output low voltage
VOH
VOH
VOL
VOL
2.4
V
V
V
V
IOH = −1 mA
IOH = −100 µA
IOL = 2 mA
VCC − 0.2
0.4
0.2
IOL = 100 µA
Rev.1.01, Nov.18.2004, page 8 of 19
R1LV1616H-I Series
Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and not guaranteed.
2. BYTE# ≥ VCC − 0.2 V or BYTE# ≤ 0.2 V
3. ICC2 is the value measured while the valid address is increasing or decreasing by one bit.
Word mode: LSB (least significant bit) is A0.
Byte mode: LSB (least significant bit) is A-1.
Capacitance
(Ta = +25°C, f = 1.0 MHz)
Parameter
Symbol
Cin
Min
Typ
Max
8
Unit
pF
Test conditions Note
Input capacitance
Input/output capacitance
Vin = 0 V
VI/O = 0 V
1
1
CI/O
10
pF
Note: 1. This parameter is sampled and not 100% tested.
Rev.1.01, Nov.18.2004, page 9 of 19
R1LV1616H-I Series
AC Characteristics
(Ta = −40 to +85°C, VCC = 2.7 V to 3.6 V, unless otherwise noted.)
Test Conditions
•
•
•
•
Input pulse levels: VIL = 0.4 V, VIH = 2.4 V
Input rise and fall time: 5 ns
Input and output timing reference levels: 1.4 V
Output load: See figures (Including scope and jig)
1.4 V
RL=500 Ω
Dout
50pF
Rev.1.01, Nov.18.2004, page 10 of 19
R1LV1616H-I Series
Read Cycle
R1LV1616H-I
-4SI, -4LI
-5SI
Min
55
10
10
10
5
Parameter
Symbol Min
Max
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
Read cycle time
tRC
45
10
10
10
5
Address access time
Chip select access time
tAA
45
45
45
30
55
55
55
35
tACS1
tACS2
tOE
Output enable to output valid
Output hold from address change
LB#, UB# access time
tOH
tBA
45
55
Chip select to output in low-Z
tCLZ1
tCLZ2
tBLZ
tOLZ
tCHZ1
tCHZ2
tBHZ
tOHZ
2, 3
2, 3
LB#, UB# enable to low-Z
2, 3
Output enable to output in low-Z
Chip deselect to output in high-Z
5
5
2, 3
0
20
20
15
15
0
20
20
20
20
1, 2, 3
1, 2, 3
1, 2, 3
1, 2, 3
0
0
LB#, UB# disable to high-Z
0
0
Output disable to output in high-Z
0
0
Write Cycle
R1LV1616H-I
-4SI, -4LI
-5SI
Min
55
50
50
40
50
0
Parameter
Symbol Min
Max
15
15
Max
20
20
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Notes
Write cycle time
tWC
tAW
tCW
tWP
tBW
tAS
45
45
45
35
45
0
Address valid to end of write
Chip selection to end of write
Write pulse width
5
4
LB#, UB# valid to end of write
Address setup time
6
7
Write recovery time
tWR
tDW
tDH
0
0
Data to write time overlap
Data hold from write time
Output active from end of write
Output disable to output in high-Z
Write to output in high-Z
25
0
25
0
tOW
tOHZ
tWHZ
5
5
2
0
0
1, 2
1, 2
0
0
Rev.1.01, Nov.18.2004, page 11 of 19
R1LV1616H-I Series
Byte Control
R1LV1616H-I
-4SI, -4LI
-5SI
Min
5
Parameter
Symbol Min
Max
Max
Unit
ms
Notes
BYTE# setup time
BYTE# recovery time
tBS
tBR
5
5
5
ms
Notes: 1. tCHZ, tOHZ, tWHZ and tBHZ are defined as the time at which the outputs achieve the open circuit
conditions and are not referred to output voltage levels.
2. This parameter is sampled and not 100% tested.
3. At any given temperature and voltage condition, tHZ max is less than tLZ min both for a given
device and from device to device.
4. A write occurs during the overlap of a low CS1#, a high CS2, a low WE# and a low LB# or a low
UB#. A write begins at the latest transition among CS1# going low, CS2 going high, WE# going
low and LB# going low or UB# going low. A write ends at the earliest transition among CS1#
going high, CS2 going low, WE# going high and LB# going high or UB# going high. tWP is
measured from the beginning of write to the end of write.
5. tCW is measured from the later of CS1# going low or CS2 going high to the end of write.
6. tAS is measured from the address valid to the beginning of write.
7. tWR is measured from the earliest of CS1# or WE# going high or CS2 going low to the end of
write cycle.
Rev.1.01, Nov.18.2004, page 12 of 19
R1LV1616H-I Series
Timing Waveform
Read Cycle*1
tRC
Address*2
Valid address
tAA
tACS1
CS1#
tCLZ1
tCHZ1
CS2
tACS2
tCLZ2
tCHZ2
tBHZ
tBA
LB#, UB#
tBLZ
tOHZ
tOE
OE#
tOLZ
tOH
High impedance
Dout*3
Valid data
Notes: 1. BYTE# > VCC – 0.2 V or
BYTE# < 0.2 V
2. Word mode: A0 to A19
Byte mode: A-1 to A19
3. Word mode: I/O0 to I/O15
Byte mode: I/O0 to I/O7
Rev.1.01, Nov.18.2004, page 13 of 19
R1LV1616H-I Series
Write Cycle (1)*1 (WE# Clock)
tWC
Valid address
Address*2
tWR
tCW
CS1#
tCW
CS2
tBW
LB#, UB#
tAW
tWP
WE#
tAS
tDW
Valid data
tDH
Din*3
tWHZ
tOW
High impedance
Dout*3
Notes: 1. BYTE# > VCC – 0.2 V or
BYTE# < 0.2 V
2. Word mode: A0 to A19
Byte mode: A-1 to A19
3. Word mode: I/O0 to I/O15
Byte mode: I/O0 to I/O7
Rev.1.01, Nov.18.2004, page 14 of 19
R1LV1616H-I Series
Write Cycle (2)*1 (CS1#, CS2 Clock, OE# = VIH)
tWC
Valid address
tAW
Address*2
tAS
tWR
tCW
CS1#
tAS
tCW
CS2
tBW
LB#, UB#
tWP
WE#
tDW
Valid data
tDH
Din*3
High impedance
Dout*3
Notes: 1. BYTE# > VCC – 0.2 V or
BYTE# < 0.2 V
2. Word mode: A0 to A19
Byte mode: A-1 to A19
3. Word mode: I/O0 to I/O15
Byte mode: I/O0 to I/O7
Rev.1.01, Nov.18.2004, page 15 of 19
R1LV1616H-I Series
Write Cycle (3)*1 (LB#, UB# Clock, OE# = VIH)
tWC
Valid address
Address
CS1#
tAW
tCW
tWR
tCW
CS2
tBW
tAS
UB# (LB#)
LB# (UB#)
tBW
tWP
WE#
tDW
tDH
Din-UB
(Din-LB)
Valid data
tDW
tDH
Din-LB
(Din-UB)
Valid data
High impedance
Dout
Note: 1. BYTE# > VCC – 0.2 V
Rev.1.01, Nov.18.2004, page 16 of 19
R1LV1616H-I Series
Byte Control (TSOP)
CS2
CS1#
tBS
tBR
BYTE#
Rev.1.01, Nov.18.2004, page 17 of 19
R1LV1616H-I Series
Low VCC Data Retention Characteristics
(Ta = −40 to +85°C)
Parameter
Symbol Min
Typ
Max
Unit
Test conditions*2, 3
VCC for data retention
VDR
1.5
3.6
V
Vin ≥ 0 V
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS2 ≥ VCC − 0.2 V,
CS1# ≥ VCC − 0.2 V or
(3) LB# = UB# ≥ VCC − 0.2 V,
CS2 ≥ VCC − 0.2 V,
CS1# ≤ 0.2 V
Data retention -4SI
ICCDR
0.5*1
0.5*1
8
µA
µA
VCC = 3.0 V, Vin ≥ 0 V
(1) 0 V ≤ CS2 ≤ 0.2 V or
(2) CS2 ≥ VCC − 0.2 V,
CS1# ≥ VCC − 0.2 V or
(3) LB# = UB# ≥ VCC − 0.2 V,
CS2 ≥ VCC − 0.2 V,
current
-5SI
-4LI
ICCDR
25
CS1# ≤ 0.2 V
Average value
Chip deselect to data
retention time
tCDR
tR
0
5
ns
See retention waveforms
Operation recovery time
ms
Notes: 1. Typical values are at VCC = 3.0 V, Ta = +25°C and not guaranteed.
2. BYTE# ≥ VCC − 0.2 V or BYTE# ≤ 0.2 V
3. CS2 controls address buffer, WE# buffer, CS1# buffer, OE# buffer, LB#, UB# buffer and Din
buffer. If CS2 controls data retention mode, Vin levels (address, WE#, OE#, CS1#, LB#, UB#,
I/O) can be in the high impedance state. If CS1# controls data retention mode, CS2 must be
CS2 ≥ VCC − 0.2 V or 0 V ≤ CS2 ≤ 0.2 V. The other input levels (address, WE#, OE#, LB#, UB#,
I/O) can be in the high impedance state.
Rev.1.01, Nov.18.2004, page 18 of 19
R1LV1616H-I Series
Low VCC Data Retention Timing Waveform (1) (CS1# Controlled)
Data retention mode
tCDR
tR
VCC
2.7 V
2.2 V
VDR
CS1#
0 V
CS1#
V
CC
– 0.2 V
≥
Low VCC Data Retention Timing Waveform (2) (CS2 Controlled)
tCDR
Data retention mode
tR
VCC
2.7 V
CS2
VDR
0.6 V
0 V
<
<
0 V CS2 0.2 V
Low VCC Data Retention Timing Waveform (3) (LB#, UB# Controlled)
Data retention mode
tCDR
tR
VCC
2.7 V
2.2 V
VDR
LB#, UB#
0 V
≥
LB#, UB# VCC – 0.2 V
Rev.1.01, Nov.18.2004, page 19 of 19
Revision History
R1LV1616H-I Series Data Sheet
Rev. Date
Contents of Modification
Page Description
1.00 Apr. 22, 2004
1.01 Nov. 18, 2004
Initial issue
Addition of 2-Mword × 8-bit function
Sales Strategic Planning Div. Nippon Bldg., 2-6-2, Ohte-machi, Chiyoda-ku, Tokyo 100-0004, Japan
Keep safety first in your circuit designs!
1. Renesas Technology Corp. puts the maximum effort into making semiconductor products better and more reliable, but there is always the possibility that trouble
may occur with them. Trouble with semiconductors may lead to personal injury, fire or property damage.
Remember to give due consideration to safety when making your circuit designs, with appropriate measures such as (i) placement of substitutive, auxiliary circuits,
(ii) use of nonflammable material or (iii) prevention against any malfunction or mishap.
Notes regarding these materials
1. These materials are intended as a reference to assist our customers in the selection of the Renesas Technology Corp. product best suited to the customer's
application; they do not convey any license under any intellectual property rights, or any other rights, belonging to Renesas Technology Corp. or a third party.
2. Renesas Technology Corp. assumes no responsibility for any damage, or infringement of any third-party's rights, originating in the use of any product data,
diagrams, charts, programs, algorithms, or circuit application examples contained in these materials.
3. All information contained in these materials, including product data, diagrams, charts, programs and algorithms represents information on products at the time of
publication of these materials, and are subject to change by Renesas Technology Corp. without notice due to product improvements or other reasons. It is
therefore recommended that customers contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor for the latest product
information before purchasing a product listed herein.
The information described here may contain technical inaccuracies or typographical errors.
Renesas Technology Corp. assumes no responsibility for any damage, liability, or other loss rising from these inaccuracies or errors.
Please also pay attention to information published by Renesas Technology Corp. by various means, including the Renesas Technology Corp. Semiconductor
home page (http://www.renesas.com).
4. When using any or all of the information contained in these materials, including product data, diagrams, charts, programs, and algorithms, please be sure to
evaluate all information as a total system before making a final decision on the applicability of the information and products. Renesas Technology Corp. assumes
no responsibility for any damage, liability or other loss resulting from the information contained herein.
5. Renesas Technology Corp. semiconductors are not designed or manufactured for use in a device or system that is used under circumstances in which human life
is potentially at stake. Please contact Renesas Technology Corp. or an authorized Renesas Technology Corp. product distributor when considering the use of a
product contained herein for any specific purposes, such as apparatus or systems for transportation, vehicular, medical, aerospace, nuclear, or undersea repeater
use.
6. The prior written approval of Renesas Technology Corp. is necessary to reprint or reproduce in whole or in part these materials.
7. If these products or technologies are subject to the Japanese export control restrictions, they must be exported under a license from the Japanese government and
cannot be imported into a country other than the approved destination.
Any diversion or reexport contrary to the export control laws and regulations of Japan and/or the country of destination is prohibited.
8. Please contact Renesas Technology Corp. for further details on these materials or the products contained therein.
RENESAS SALES OFFICES
http://www.renesas.com
Refer to "http://www.renesas.com/en/network" for the latest and detailed information.
Renesas Technology America, Inc.
450 Holger Way, San Jose, CA 95134-1368, U.S.A
Tel: <1> (408) 382-7500, Fax: <1> (408) 382-7501
Renesas Technology Europe Limited
Dukes Meadow, Millboard Road, Bourne End, Buckinghamshire, SL8 5FH, U.K.
Tel: <44> (1628) 585-100, Fax: <44> (1628) 585-900
Renesas Technology Hong Kong Ltd.
7th Floor, North Tower, World Finance Centre, Harbour City, 1 Canton Road, Tsimshatsui, Kowloon, Hong Kong
Tel: <852> 2265-6688, Fax: <852> 2730-6071
Renesas Technology Taiwan Co., Ltd.
10th Floor, No.99, Fushing North Road, Taipei, Taiwan
Tel: <886> (2) 2715-2888, Fax: <886> (2) 2713-2999
Renesas Technology (Shanghai) Co., Ltd.
Unit2607 Ruijing Building, No.205 Maoming Road (S), Shanghai 200020, China
Tel: <86> (21) 6472-1001, Fax: <86> (21) 6415-2952
Renesas Technology Singapore Pte. Ltd.
1 Harbour Front Avenue, #06-10, Keppel Bay Tower, Singapore 098632
Tel: <65> 6213-0200, Fax: <65> 6278-8001
© 2004. Renesas Technology Corp., All rights reserved. Printed in Japan.
Colophon .2.0
R1LV1616HSA-4LI 相关器件
型号 | 制造商 | 描述 | 价格 | 文档 |
R1LV1616HSA-4SI | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword × 16-bit / 2-Mword × 8-bit) | 获取价格 | |
R1LV1616HSA-4SI#B0 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616HSA-4SI#B1 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616HSA-4SI#S0 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616HSA-5SI | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword × 16-bit / 2-Mword × 8-bit) | 获取价格 | |
R1LV1616HSA-5SI#B0 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616HSA-5SI#B1 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616HSA-5SI#S0 | RENESAS | Wide Temperature Range Version 16 M SRAM (1-Mword x 16-bit / 2-Mword x 8-bit) | 获取价格 | |
R1LV1616R | RENESAS | 16Mb superSRAM (1M wordx16bit) | 获取价格 | |
R1LV1616RBA-5SI | RENESAS | 16Mb Advanced LPSRAM (1M wordx16bit / 2M wordx8bit) | 获取价格 |
R1LV1616HSA-4LI 相关文章
- 2024-09-20
- 5
- 2024-09-20
- 9
- 2024-09-20
- 8
- 2024-09-20
- 6