BD7J200EFJ-LB [ROHM]
本产品是面向工业设备市场的产品,保证可长期稳定供货。适合用于工业设备的绝缘电源。本产品是无需光电耦合器的绝缘型反激式转换器。无需以往用途中为获得稳定输出电压所需的光电耦合器、变压器3次绕组构成的反馈电路。还采用了独创的适应型导通时间控制技术,不需要外接相位补偿部件,可大幅减少部件个数,并实现小型、高可靠性的绝缘型电源应用设计。;型号: | BD7J200EFJ-LB |
厂家: | ROHM |
描述: | 本产品是面向工业设备市场的产品,保证可长期稳定供货。适合用于工业设备的绝缘电源。本产品是无需光电耦合器的绝缘型反激式转换器。无需以往用途中为获得稳定输出电压所需的光电耦合器、变压器3次绕组构成的反馈电路。还采用了独创的适应型导通时间控制技术,不需要外接相位补偿部件,可大幅减少部件个数,并实现小型、高可靠性的绝缘型电源应用设计。 变压器 光电 转换器 |
文件: | 总41页 (文件大小:1557K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Datasheet
Isolated Flyback Converter IC
With Integrated Switching MOSFET
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
General Description
Key Specifications
This is the product guarantees long time support in
Industrial market.
◼ Operation Supply Voltage Range
VIN Pin:
8 V to 80 V
120 V (Max)
1.75 A (Typ)
400 kHz (Typ)
±1.5 %
This IC is an optocoupler-less isolated flyback converter.
It is not necessary to use any optocouplers and feedback
circuits by a third winding of transformers; these have
been ever required to obtain a stable output voltage in
SW Pin:
◼ Over Current Detection Current:
◼ Switching Frequency:
◼ Reference Voltage Accuracy:
◼ Current at Shutdown:
◼ Operation Current at Switching:
former applications.
Furthermore, adoption of the
0 μA (Typ)
2.8 mA (Typ)
original adapted type technology that controls on time
makes the external phase compensation parts
unnecessary, reduces a lot of parts number and
minimalizes applications, which realizes the designs of
isolated power supply application with high reliability.
◼ Operation Temperature Range: -40 °C to +125 °C
Packages
W (Typ) x D (Typ) x H (Max)
2.9 mm x 3.0 mm x 0.6 mm
HSON8
(BD7J200HFN-LB)
Features
HTSOP-J8
(BD7J200EFJ-LB BD7J200UEFJ-LB)
4.9 mm x 6.0 mm x 1.0 mm
◼ Long Time Support Product for Industrial Applications
◼ No Need of Any Optocoupler and Third Winding of
Transformer
◼ Set Output Voltage with Two External Resistor and
Ratio of Transformer Turns
◼ Adopt of Original Adapted Type Technology that
Controls On Time.
◼ No Need of External Phase Compensation Parts by
High-speed Load Response
◼ Low Output Ripple by Fixed Switching Frequency
(At normal operation)
◼ High Efficient Light Load Mode (At PFM operation)
◼ Shutdown and Enable Control
◼ Built-in 120 V Switching MOSFET
◼ Soft Start Function
HSON8
HTSOP-J8
◼ Load Compensation Function
◼ Various Protection Function
Application
Isolated Power Supply for Industrial Equipment
Input Under Voltage Lockout (VIN UVLO)
Over Current Protection (OCP)
◼
Over Voltage Protection (OVP)
Short Circuit Protection (SCP)
Thermal Shutdown (TSD)
Battery Short Protection (BSP)
Typical Application Circuit
VIN
SDX/EN
SW
FB
L_COMP
AGND REF PGND
〇Product structure : Silicon integrated circuit 〇This product has no designed protection against radioactive rays.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
1/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Pin Configurations
(TOP VIEW)
(TOP VIEW)
AGND
1
2
3
4
8
7
6
5
VIN
AGND 1
SDX/EN 2
L_COMP 3
REF 4
8 VIN
7 SW
6 PGND
5 FB
SDX/EN
L_COMP
REF
SW
PGND
FB
EXP-PAD
EXP-PAD
HSON8
HTSOP-J8
Pin Descriptions
Pin No.
Pin Name
Function
1
2
3
4
5
6
7
8
-
AGND
SDX/EN
L_COMP
REF
Analog system GND pin
Shutdown and enable control pin
Setting pin of the load current compensation value
Setting pin of the output voltage
Setting pin of the output voltage
Power system GND pin
FB
PGND
SW
Switching output pin
VIN
Power supply input pin
EXP-PAD
Connect EXP-PAD to both of the AGND and PGND pins
Block Diagram
8
5
7
VIN
FB
SW
Current Monitor
INTERNAL
REGULATOR
SCP
OVP
VINTREF
COMPARATOR
Switching
MOSFET
ADAPTIVE
ON-TIME
CONTROLLER
Shutdown
VINTREF
SOFT
DRIVER
Enable
2
SDX/EN
VIN UVLO
TSD
START
OCP
BSP
LOAD
COMPENSATION
PGND
REF
L_COMP
AGND
1
4
3
6
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
2/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Description of Blocks
1
INTERNAL REGULATOR
This is the regulator block for internal circuits.
This block also shuts itself down at the shutdown status of the SDX/EN pin voltage ≤ VSDX
.
The SDX/EN pin voltage becomes VEN1 or more, the IC becomes enable status and the output voltage rises slowly by
the soft start function. The SDX/EN pin voltage becomes VEN2 or less, the IC becomes disable status and stops the
switching operation.
VIN pin voltage
VEN1
VEN2
SDX/EN pin voltage
tSS
Setting output voltage
Setting output voltage × 0.9
Output voltage
Switching
ON
Figure 1. Startup and Stop Timing Chart
In the control method of this IC, it is necessary to operate in the status that the duty is DMAX or less. At the startup
and stop, set the VIN pin voltage VIN to meet the next formula.
ꢀ푃
ꢀ푆
1
[V]
(
)
푉 >
퐼푁
× 푉푂푈푇 + 푉퐹 ꢁ
− 1ꢂ
퐷푀퐴푋
Where:
is the VIN pin voltage.
푉
퐼푁
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
푉푂푈푇 is the output voltage.
푉퐹 is the forward voltage of the secondary output diode.
퐷푀퐴푋 is the maximum duty.
In the case that the SDX/EN pin is shorted to the VIN pin the duty becomes DMAX or more at startup and stop, and
there may be occur the output voltage without intending. Refer to Application Examples: 6 Enable Voltage and
Disable Voltage for the enable control by the VIN pin.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
3/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Description of Blocks – continued
2
VIN UVLO
This is the input low voltage protection block.
When the VIN pin voltage becomes VUVLO1 or less, the IC detects VIN UVLO and stops the switching operation because
of the high impedance in the SW pin.
When the VIN pin voltage becomes VUVLO2 or more, the IC automatically reset via the soft start.
VIN pin voltage
VUVLO2
VUVLO1
0 V
tSS
Setting output voltage
Setting output voltage × 0.9
Output voltage
Switching
ON
ON
Figure 2. VIN UVLO Timing Chart
3
4
5
SOFT START
When the status becomes enable that the SDX/EN pin voltage VEN1 or more, the comparison voltage in the comparator
block transits slowly 0 V to VINTREF This operation pretend the IC from rushing current at the rising edge of the output
.
voltage or overshooting. The soft start time is fixed to tSS in the IC.
COMPARATOR
In this block, the IC compare the reference voltage to the REF pin voltage that is the feedback voltage of the SW pin
voltage. This IC is superior to the response for fluctuation in load because it constitutes the feedback group by the
comparator.
ADAPTIVE ON TIME CONTROLLER
This block is corresponded to the original adapted type technology that controls on time.
Stable load current:
Operates in the PWM control and fix the on time.
Fluctuating load current:
Operates in the on time control and realizes a high-speed load response by
fluctuates the switching frequency.
Light load:
Decrease the switching frequency and realizes a high efficiency.
When the load current fluctuates, the frequency becomes high. The IC raises the average of primary current by
shortening the off time and raises the secondary current.
Output voltage
Primary coil current
SW pin voltage
High
Frequency
Stabilize gradually
Stable operation
Switching Frequency
Figure 3. Transient Response Timing Chart
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
4/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Description of Blocks – continued
6
DRIVER
This block drives the switching MOSFET.
7
LOAD COMPENSATION
This block compensates the fluctuation of output voltage caused by the fluctuation of VF characteristic in the secondary
output diode corresponded to load current. This block monitors the current flowed to the switching MOSFET and
pulls the current corresponded to the quantity of compensation determined by the external resistor and capacitor at
the L_COMP pin and time constant from the REF pin. The decline of the REF pin voltage by the drop of feedback
current flowing in the external resistor at the REF pin rises the output voltage and it is compensated.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
5/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Description of Blocks – continued
8
OCP, BSP
This is the block of the over current protection and battery short protection.
8.1
OCP (Over Current Protection)
At the switching MOSFET on, the IC detects the OCP when the peak current becomes ILIMIT or more. At this
moment, the switching MOSFET is turned off. Because of detecting per switching cycles and restricting on duty,
the output voltage drops. In addition, to prevent detection error, the detection of OCP is invalidated for tMASK1
after the switching MOSFET is turned on
Output voltage
ILIMIT
Primary coil current
SW pin voltage
tMASK1
Normal
Normal
OCP
IC status
Figure 4. OCP Timing Chart
8.2
BSP (Battery Short Protection)
If the SW pin is connected to high electric potential with low impedance, current flows when the switching
MOSFET turned on and it may destroy the IC.
To prevent this, the IC has a built-in BSP. When the SW pin voltage becomes VBSP or more at the switching
MOSFET on, the IC detects BSP. At this moment, the switching operation is stopped. After tRESTART from the
stop, the IC operates the soft start and resets.
tSS
Setting output voltage
Setting output voltage × 0.9
Output voltage
SW pin voltage
VBSP
ON
ON
Switching
tRESTART
Figure 5. BPS Timing Chart
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
6/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Description of Blocks – continued
9
SCP, OVP
This is the block of the short circuit protection and over voltage protection.
9.1
SCP (Short Circuit Protection)
The REF pin obtains the secondary output voltage data from the primary flyback voltage. When the REF pin
voltage becomes VSCP or less at the switching MOSFET off, the IC detects SCP. At this moment, the switching
operation is stopped. After tRESTART from the stop, the IC operates the soft start and resets.
To prevent detection error, the detection of SCP is invalidated for tMASK2 after the switching MOSFET is turned off
and for tMASK3 at the startup by the soft start.
In the case that the primary flyback voltage is not output correctly, SCP is not detected even if the secondary
output voltage drops.
tSS
Setting output voltage
Setting output voltage × 0.9
Output voltage
SW pin voltage
VSCP
REF pin voltage
Switching
ON
Figure 6. SCP Timing Chart
ON
tRESTART
9.2
OVP (Over Voltage Protection)
The REF pin obtains the secondary output voltage data from the primary flyback voltage. When the REF pin
voltage becomes VOVP or more at the switching MOSFET off, the IC detects OVP. At this moment, the switching
operation is stopped. After tRESTART from the stop, the IC operates the soft start and resets.
To prevent detection error, the detection of OVP is invalidated for tMASK2 after the switching MOSFET is turned off.
In the case that the primary flyback voltage is not output correctly, OVP is not detected even if the secondary
output voltage rises.
tSS
Setting output voltage
Setting output voltage × 0.9
Output voltage
SW pin voltage
VOVP
REF pin voltage
ON
ON
Switching
tRESTART
Figure 7. OVP Timing Chart
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
7/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Absolute Maximum Ratings (Ta = 25 °C)
Parameter
VIN Pin Voltage
Symbol
Rating
Unit
100
VIN_MAX
VSW_MAX
VSDX/EN_MAX
VFB_MAX
V
V
120
SW Pin Voltage
100
SDX/EN Pin Voltage
FB Pin Voltage
V
VIN + 0.3
V
7
REF Pin Voltage
VREF_MAX
VL_COMP_MAX
Tjmax
V
7
L_COMP Pin Voltage
Maximum Junction Temperature
Storage Temperature Range
V
150
°C
Tstg
-55 to +150
°C
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins or an open circuit
between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such as adding a fuse, in case the IC is
operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in deterioration of the
properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal resistance taken into consideration by increasing
board size and copper area so as not to exceed the maximum junction temperature rating.
Thermal Resistance (Note 1)
Thermal Resistance (Typ)
Parameter
Symbol
Unit
1s(Note 3)
2s2p(Note 4)
HSON8
Junction to Ambient
Junction to Top Characterization Parameter(Note 2)
θJA
265.1
17
66.1
9
°C/W
°C/W
ΨJT
HTSOP-J8
Junction to Ambient
Junction to Top Characterization Parameter(Note 2)
θJA
206.4
21
45.2
13
°C/W
°C/W
ΨJT
(Note 1) Based on JESD51-2A (Still-Air).
(Note 2) The thermal characterization parameter to report the difference between junction temperature and the temperature at the top center of the outside surface
of the component package.
(Note 3) Using a PCB board based on JESD51-3.
(Note 4) Using a PCB board based on JESD51-5, 7.
Layer Number of
Measurement Board
Material
FR-4
Board Size
Single
114.3 mm x 76.2 mm x 1.57 mmt
Top
Copper Pattern
Thickness
70 μm
Footprints and Traces
Layer Number of
Measurement Board
Thermal Via(Note 5)
Material
FR-4
Board Size
114.3 mm x 76.2 mm x 1.6 mmt
2 Internal Layers
Pitch
Diameter
4 Layers
1.20 mm
Φ0.30 mm
Top
Copper Pattern
Bottom
Thickness
70 μm
Copper Pattern
Thickness
35 μm
Copper Pattern
Thickness
70 μm
Footprints and Traces
74.2 mm x 74.2 mm
74.2 mm x 74.2 mm
(Note 5) This thermal via connects with the copper pattern of all layers.
Recommended Operating Conditions
Parameter
Symbol
Min
Typ
Max
Unit
Conditions
Operation Power Supply Voltage Range 1
Operation Power Supply Voltage Range 2
VIN
8
-
48
-
80
110
0.5
V
V
The VIN pin voltage
The SW pin voltage
The L_COMP pin voltage
VSW
Operation Power Supply Voltage Range 3 VL_COMP_MAX2
Operation Temperature Topr
-
-
V
-40
-
+125
°C
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
8/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Electrical Characteristics
(Unless otherwise specified VIN = 48 V, VSDX/EN = 2.5 V, Ta = 25 °C)
Parameter
Power Supply Block
Symbol
Min
Typ
Max
Unit
Conditions
VSDX/EN = 0 V
Current at Shutdown
IST
ICC
-
-
0
10
6.0
6.0
-
μA
mA
V
VREF = 0.85 V (At PFM operation)
At VIN falling
Current at Switching Operation
UVLO Detection Voltage 1
UVLO Detection Voltage 2
UVLO Voltage Hysteresis
2.8
5.0
5.2
0.2
VUVLO1
VUVLO2
VUVLO_HYS
4.1
-
V
At VIN rising
0.1
0.3
V
Shutdown and Enable Control Block
Shutdown Voltage
VSDX
VEN1
-
1.7
-
-
0.3
2.3
-
V
V
Enable Voltage 1
2.0
1.8
0.2
2.5
5.3
815
190
At VSDX/EN rising
At VSDX/EN falling
Enable Voltage 2
VEN2
V
Enable Voltage Hysteresis
SDX/EN Pin Inflow Current
SDX/EN Pin Clamp Voltage
SDX/EN Pin Pull-down Resistance 1
SDX/EN Pin Pull-down Resistance 2
VEN_HYS
ISDX/EN
VCLPEN
RSDX/EN1
RSDX/EN2
0.1
1.6
-
0.3
3.9
-
V
μA
V
-
-
kΩ
kΩ
-
-
Reference Voltage Block
Reference Voltage
REF Pin Current
VINTREF
IREF
0.768
-
0.780
390
0.792
-
V
μA
Switching Block
On Resistance
RON
ILIMIT
0.25
1.40
-
0.50
1.75
400
1.00
350
450
20
1.00
2.10
-
Ω
A
Between the SW and PGND pins
Over Current Detection Current
Switching Frequency
On Time
fSW
kHz At PWM operation (Duty = 40 %)
tON
0.75
260
335
14
1.25
440
565
26
μs At PWM operation (Duty = 40 %)
Minimum On Time
Minimum Off Time
Maximum Off Time
Soft Start Time
tON_MIN
tOFF_MIN
tOFF_MAX
tSS
ns
ns
μs
1.2
-
2.5
5.0
-
ms From rise-up to VREF x 90 %
Maximum Duty
DMAX
DMIN
50
%
%
Minimum Duty
-
20
-
Protection Function Block
Short Protection Detection Voltage
Over Voltage Protection Detection Voltage
Battery Short Protection Detection Voltage
Restart Time
VSCP
VOVP
-
-
-
-
-
0.50
0.95
2.0
-
-
-
-
-
V
V
VBSP
V
tRESTART
tMASK1
tMASK2
tMASK3
2.0
ms
ns
Over Current Protection Mask Time
280
Short and Over Voltage Protection
Mask Time
-
-
400
600
-
-
ns
μs
Short Protection Mask Time at Startup
Load Compensation Block
Internal Resistor at L_COMP Pin
RINTCOMP
K
-
-
50
-
-
kΩ
%
Compressor Magnification
in Current Monitor
0.004
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
9/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves
(Reference Data)
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-40 -20
0 20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 8. Current at Shutdown vs Temperature
Figure 9. Current at Switching Operation vs Temperature
6.0
5.5
5.0
4.5
4.0
6.0
5.5
5.0
4.5
4.0
-40 -20
0
20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 10. UVLO Detection Voltage 1 vs Temperature
Figure 11. UVLO Detection Voltage 2 vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
10/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
Figure 12. UVLO Voltage Hysteresis vs Temperature
Figure 13. SDX/EN Pin Clamp Voltage vs Temperature
Figure 14. Enable Voltage 1 vs Temperature
Figure 15. Enable Voltage 2 vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
11/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
0.40
0.35
0.30
0.25
0.20
0.15
0.10
0.05
0.00
10.0
9.0
8.0
7.0
6.0
5.0
4.0
3.0
2.0
1.0
0.0
-40 -20 0 20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 16. Enable Voltage Hysteresis vs Temperature
Figure 17. SDX/EN Pin Inflow Current vs Temperature
0.90
0.85
0.80
0.75
0.70
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0.0
-40 -20
0
20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 18. Reference Voltage vs Temperature
Figure 19. On Resistance vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
12/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
2.50
2.00
1.50
1.00
0.50
0.00
600
500
400
300
200
-40 -20
0
20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 20. Over Current Detection Current vs Temperature
Figure 21. Switching Frequency vs Temperature
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
600
550
500
450
400
350
300
250
200
-40 -20
0
20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 22. On Time vs Temperature
Figure 23. Minimum On Time vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
13/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
600
500
400
300
200
30.0
25.0
20.0
15.0
10.0
5.0
0.0
-40 -20
0
20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 24. Minimum Off Time vs Temperature
Figure 25. Maximum Off Time vs Temperature
5.00
4.50
4.00
3.50
3.00
2.50
2.00
1.50
1.00
0.50
0.00
0.60
0.55
0.50
0.45
0.40
-40 -20
0
20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 26. Soft Start Time vs Temperature
Figure 27. Short Protection Detection Voltage vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
14/38
20.Mar.2023 Rev.002
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
1.10
1.05
1.00
0.95
2.50
2.30
2.10
1.90
1.70
1.50
0.90
-40 -20 0 20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 28. Over Voltage Protection Detection Voltage
vs Temperature
Figure 29. Battery Short Protection Detection Voltage
vs Temperature
600
500
400
300
600
500
400
300
200
200
-40 -20 0 20 40 60 80 100120140
-40 -20 0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 30. Over Current Protection Mask Time
vs Temperature
Figure 31. Short and Over Voltage Protection Mask Time
vs Temperature
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
15/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
1000
900
800
700
600
500
400
300
200
100
5.0
4.0
3.0
2.0
1.0
0.0
0
-40 -20 0 20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 32. Short Protection Mask Time at Startup
vs Temperature
Figure 33. Restart Time vs Temperature
600
500
400
300
200
13.0
12.5
12.0
11.5
11.0
-40 -20
0 20 40 60 80 100120140
-40 -20
0 20 40 60 80 100120140
Temperature [°C]
Temperature [°C]
Figure 34. Secondary Output Voltage vs Temperature
(IOUT = 420 mA)
Figure 35. Switching Frequency vs Temperature
(IOUT = 420 mA)
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
16/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
100
90
80
70
60
50
40
30
20
10
0
13.0
12.8
12.6
12.4
12.2
12.0
11.8
11.6
11.4
11.2
11.0
withoutcompensation
with compensation
0
200
400
600
800 1000
0
200
400
600
800 1000
Load Current[mA]
Load Current[mA]
Figure 36. Efficiency vs Load Current
Figure 37. Output Voltage vs Load Current
VIN: 20 V/Div
VIN: 20 V/Div
VSDX/EN: 2 V/Div
VSDX/EN: 2 V/Div
VOUT: 2 V/Div
VSW: 40 V/Div
VOUT: 2 V/Div
VSW: 40 V/Div
Figure 38. Startup Waveform (The SDX/EN Pin Control)
Figure 39. Shutdown Waveform (The SDX/EN Pin Control)
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
17/38
20.Mar.2023 Rev.002
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Typical Performance Curves – continued
(Reference Data)
VIN: 20 V/Div
VIN: 20 V/Div
VSDX/EN: 2 V/Div
VOUT: 2 V/Div
VSW: 40 V/Div
VSDX/EN: 2 V/Div
VOUT: 2 V/Div
VSW: 40 V/Div
Figure 40. Startup Waveform (The VIN Pin Control)
Figure 41. Shutdown Waveform (The VIN Pin Control)
20
18
16
14
12
10
8
IOUT: 500 mA/Div
VOUT: 500 mV/Div
6
4
2
0
0
10 20 30 40 50 60 70 80 90 100
VIN Pin Voltage [V]
Figure 42. Load Transient Response
(IOUT = 0.1 A to 0.83 A)
Figure 43. Maximum Output Power vs VIN Pin Voltage
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
18/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples
1
Output Voltage
When the internal switching MOSFET is off, the SW pin voltage becomes higher than the VIN pin voltage. The
secondary output voltage is calculated by the primary flyback voltage, which is described by the difference between
this SW pin voltage and VIN pin voltage. The SW pin voltage at turn off is calculated by the formula below.
ꢀ푃
( )
× 푉푂푈푇 + 푉퐹 + ꢃ푆 × 퐸ꢄ푅
푉
푆푊
= 푉 +
[V]
퐼푁
ꢀ푆
Where:
푉
푉
퐼푁
is the SW pin voltage.
is the VIN pin voltage.
푆푊
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
푉푂푈푇 is the output voltage.
푉퐹 is the forward voltage of the secondary output diode.
ꢃ푆 is the secondary transformer current.
퐸ꢄ푅 is the secondary total impedance (secondary transformer winding resistance and PCB impedance).
The external resistor RFB between the FB and SW pins converts the primary flyback voltage into the FB pin inflow
current IRFB. The FB pin inflow current IRFB is calculated by the formula below because the FB pin voltage is nearly
equal to the VIN pin voltage by the IC’s internal circuit.
푉
− 푉퐹퐵
푆푊
ꢃꢅ퐹퐵
=
=
=
푅퐹퐵
ꢀ푃
ꢀ푆
(
)
푉 +
퐼푁
× 푉푂푈푇 + 푉퐹 + ꢃ푆 × 퐸ꢄ푅 − 푉퐹퐵
푅퐹퐵
ꢀ푃
ꢀ푆
(
)
× 푉푂푈푇 + 푉퐹 + ꢃ푆 × 퐸ꢄ푅
[A]
푅퐹퐵
Where:
ꢃꢅ퐹퐵 is the FB pin inflow current.
푉퐹퐵 is the FB pin voltage.
푅퐹퐵 is the external resistor between the FB and SW pins.
Furthermore, the REF pin voltage is calculated by the formula below because the FB pin inflow current flows into the
external resistor RREF between the REF and AGND pins.
푅ꢅꢆ퐹 ꢀ푃
( )
× 푉푂푈푇 + 푉퐹 + ꢃ푆 × 퐸ꢄ푅
푉ꢅꢆ퐹
=
×
[V]
푅퐹퐵 ꢀ푆
Where:
푉ꢅꢆ퐹 is the REF pin voltage.
푅ꢅꢆ퐹 is the external resistor between the REF and AGND pins.
The resistor RREF is necessary to be set as the current flowing in the REF pin becomes IREF when the REF pin voltage
is equal to VINTREF
.
This IC’s internal circuit is designed as RREF = 2 kΩ according to the formula below.
푉
퐼푁푇ꢅꢆ퐹
푅ꢅꢆ퐹
=
[Ω]
ꢃꢅꢆ퐹
Where:
푉
is the REF pin voltage.
퐼푁푇ꢅꢆ퐹
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
19/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
1
Output Voltage – continued
The REF pin voltage is input to the comparator with the reference voltage in the IC. By the internal circuit, the REF
pin voltage becomes equal to the reference voltage. Therefore, the output voltage and the REF pin voltage is
calculated by the formula below.
푅퐹퐵 ꢀ푆
[V]
푉푂푈푇
=
×
× 푉ꢅꢆ퐹 − 푉퐹 − ꢃ푆 × 퐸ꢄ푅
푅ꢅꢆ퐹 ꢀ푃
The output voltage is set by the number of winding ratio of the primary and secondary transformer and the resistance
ratio of RFB and RREF In addition, VF and ESR is factor of the error in the output voltage. According to the relational
.
expression in above, the external resistor between the FB and SW pins RFB is calculated by the formula below.
푅ꢅꢆ퐹 ꢀ푃
(
)
푅퐹퐵
=
×
× 푉푂푈푇 + 푉퐹 + ꢃ푆 × 퐸ꢄ푅
[Ω]
푉ꢅꢆ퐹 ꢀ푆
VF
IS
VIN
NP/NS
VOUT
IRFB
RFB
FB
SW
COMPARATOR
ADAPTIVE
DRIVER
ON-TIME
CONTROLLER
VINTREF
IP
VL_COMP
Current
Monitor
IL_COMP
REF
PGND
L_COMP
CL_COMP
RREF
RL_COMP
Figure 44. Control Block Diagram
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
20/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
2
Transformer
2.1 Number of Winding Ratio
The number of winding ration is the parameter with which the output voltage, maximum output electric power,
duty and the SW pin voltage is set.
The duty of flyback converter is calculated by the formula below.
ꢀ푃
ꢀ푆
(
)
× 푉푂푈푇 + 푉퐹
퐷푢푡푦 =
[%]
ꢀ푃
ꢀ푆
( )
× 푉푂푈푇 + 푉퐹
푉 +
퐼푁
Where:
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
푉푂푈푇 is the output voltage.
푉퐹 is the forward voltage of the secondary output diode.
푉
퐼푁
is the VIN pin voltage.
The feedback voltage is monitored at the SW pin. In addition, it is necessary to set the duty to DMAX or less for
the stable control. By the restriction of the minimum on time, the minimum duty is determined to DMIN and the
number of winding ratio has to meet the requirements below.
퐷푀퐼푁
푉
ꢀ푃
푉
퐼푁
퐼푁
×
<
<
1 − 퐷푀퐼푁 푉푂푈푇 + 푉퐹 ꢀ푆 푉푂푈푇 + 푉퐹
Where:
퐷푀퐼푁 is the minimum duty.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
21/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
2
Transformer – continued
2.2
Primary Inductance
The right half plane zero point occurs in the feedback group of flyback converter. The phase delays 90 ° by this,
it is necessary to set the right half plane zero frequency fRHP_ZERO to the switching frequency fSW or less. The
right half plane zero frequency fRHP_ZERO is calculated by the formula below.
2
2
ꢀ
푉
퐼푁
ꢇ
푃ꢈ × {
} × 푅푂푈푇
ꢀ푃
ꢀ푆
ꢀ푆
( )
× 푉푂푈푇 + 푉퐹
푉 +
퐼푁
푓
=
[Hz]
ꢅ퐻푃_푍ꢆꢅ푂
ꢀ푃
ꢀ푆
(
)
× 푉푂푈푇 + 푉퐹
ꢉ휋 ×
× 퐿푃
ꢀ푃
( )
× 푉푂푈푇 + 푉퐹
푉 +
퐼푁
ꢀ푆
Where:
푓
is the right half plane zero frequency.
ꢅ퐻푃_푍ꢆꢅ푂
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
is the VIN pin voltage.
푉
퐼푁
푉푂푈푇 is the output voltage.
푉퐹 is the forward voltage of the secondary output diode.
푅푂푈푇 is the load resistance.
퐿푝 is the primary inductance.
For the insurance of stability, the right half plane zero frequency fRHP_ZERO has to be set to more than one quarter
of the switching frequency fSW
.
From this, the condition below is required.
1
푓
> × 푓
ꢅ퐻푃_푍ꢆꢅ푂
푆푊
4
2
ꢉ × 퐷푢푡푦 × 푉
퐼푁
퐿푝 <
[H]
(
)
푉푂푈푇 + 푉퐹 × ꢃ푂푈푇_푀퐴푋 × 휋 × 푓
푆푊
Where:
is the switching frequency.
푓
푆푊
ꢃ푂푈푇_푀퐴푋 is the maximum value of the output current.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
22/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
2.2
Primary Inductance – continued
The minimum value of primary inductance can be found by the relation of in/output electric power. If the LP
becomes lower, the peak current of primary transformer becomes higher. Because the necessary output voltage
cannot be obtained if the peak current value becomes the over current detection current or more, the lower limit
of necessary primary inductance value corresponding to maximum load is calculated by the conditional
expression below.
1
퐿푝 > ×
ꢉ
푉
2 × 푡푆 × 퐷푢푡푦2 × 휂
퐼푁
[H]
ꢃꢊ퐼푀퐼푇_푀퐼푁 × 퐷푢푡푦 × 푉 × 휂 − 푉푂푈푇_푀퐴푋 × ꢃ푂푈푇_푀퐴푋
퐼푁
Where:
푡푆 is the cycle of switching.
휂 is the efficiency.
ꢃꢊ퐼푀퐼푇_푀퐼푁 is the minimum value of over current detection current.
푉푂푈푇_푀퐴푋 is the maximum value of output voltage.
According to the above, the primary inductance is necessary to meet the requirements below.
1
ꢉ
푉
2 × 푡푆 × 퐷푢푡푦2 × 휂
퐼푁
×
ꢃꢊ퐼푀퐼푇_푀퐼푁 × 퐷푢푡푦 × 푉 × 휂 − 푉푂푈푇_푀퐴푋 × ꢃ푂푈푇_푀퐴푋
퐼푁
2
ꢉ × 퐷푢푡푦 × 푉
퐼푁
< 퐿푝 <
[H]
(
)
푉푂푈푇 + 푉퐹 × ꢃ푂푈푇_푀퐴푋 × 휋 × 푓
푆푊
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
23/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
2
Transformer – continued
2.3
Leak Inductance
The leak inductance of transformer causes the ringing at the SW pin at the moment the internal switching
MOSFET is turned off. Insert the snubber circuit not to exceed the absolute maximum rating of the SW pin
voltage. It is necessary to settle down within tMASK2 for the prevention of the error in the secondary output voltage.
In addition, it is important to consider that it is not exceeded the rating voltage of secondary output diode at the
moment the internal switching MOSFET is turned on.
Voltage
VSW_MAX
<tMASK2
(Note 1)
Primary Flyback Voltage
VIN
Time
ꢀꢎ
( )
× 푉ꢏꢐꢑ + 푉ꢒ + ꢃꢄ × 퐸ꢄ푅
Primary Flyback Voltage =
(Note 1)
ꢀ
ꢄ
Figure 45. Leak Inductance
2.4
2.5
Winding Resistance
The primary winding resistance lowers the efficiency of electricity and the secondary winding resistance lowers
the output voltage as well as it. According to them, it is recommended to use the small winding resistance
transformer.
Saturated Current
Because the core of transformer saturates if the primary transformer current exceeds the rating saturated current,
the energy does not transmit to the secondary side. The primary transformer current increases rapidly because
the inductance value drops if the core saturates. Set the primary transformer current to less than the rating
saturated current.
3
Output Capacitor
It is necessary to select the proper secondary output capacitor for the stable operation. Refer to the indication of the
capacitor and select the appropriate capacitor.
2
1
ꢀ푃
퐶푂푈푇 = 1.6 × 10ꢋ9
×
× ꢁ × 퐷푢푡푦ꢂ
ꢀ푆
[F]
퐿푃
Where:
퐶푂푈푇 is the value of output capacitor.
퐿푃 is the primary inductance.
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
In addition, it is necessary to rise up within tSS for the secondary output voltage. Therefore, also consider the condition
below to select the output capacitor. The startup error may occur because the over current protection operates by
the plunging current at startup if the capacitor value is extremely large.
ꢀ푃
ꢀ푆
(
)
푡푆푆 × ꢌꢇꢃꢊ퐼푀퐼푇_푀퐼푁
×
ꢈ × 1 − 퐷푢푡푦 − ꢃ푂푈푇_푀퐴푋
ꢍ
1
퐶푂푈푇 ≤ ×
ꢉ
[F]
푉푂푈푇
Where:
푡푆푆 is the soft start time.
ꢃꢊ퐼푀퐼푇_푀퐼푁 is the minimum value of over current detection current.
ꢃ푂푈푇_푀퐴푋 is the maximum value of output current.
푉푂푈푇 is the output voltage.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
24/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
4
Input Capacitor
Use the ceramic capacitor for the input capacitor and locate the input capacitor as near as possible to the VIN pin.
The pattern of board and location of capacitor may occur the errors.
It is necessary to set the value of input capacitor so that the ripple voltage of the VIN pin becomes 4 % or less of the
VIN pin voltage. Also, consider in the load fluctuation and startup.
5
Secondary Output Diode
It is recommended to use the schottky barrier diode whose forward voltage of the secondary output diode VF is small
because the VF becomes the factor of error in the output voltage. Select the secondary output diode so that the
forward current does not exceed the rating. The reverse voltage occurring at the secondary output diode VR is
calculated by the next formula when the internal switching MOSFET is on.
ꢀ푆
[V]
푉ꢅ = 푉 ×
+ 푉푂푈푇
퐼푁
ꢀ푃
Where:
푉ꢅ is the reverse voltage at the secondary output diode.
is the VIN pin voltage.
푉
퐼푁
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
푉푂푈푇 is the output voltage.
Furthermore, the ringing piles up the reverse voltage at the secondary output diode VR at the moment the internal
switching MOSFET is turned on. Set the peak voltage of VR to less than the rating of secondary output diode.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
25/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
6
Enable Voltage and Disable Voltage
This IC becomes shutdown status when the SDX/EN pin voltage becomes VSDX or less. At the rise-up of the SDX/EN
pin voltage, the IC becomes enable status when the voltage becomes VEN1 or more and starts the operation. At the
fall, the IC becomes disable status when the voltage becomes VEN2 or less.
Shown as Figure 45, the SDX/EN pin realizes the enable control with the VIN pin by connecting the circuit divided by
the resistor R1 and R2 between the VIN and AGND pins to the SDX/EN pin.
Remind that the internal clamp element turned on and the inflow current occurs if the SDX/EN pin voltage becomes
VCLPEN or more.
6.1
Enable Voltage
The enable voltage at the rise-up of the VIN pin voltage VIN_ENABLE is calculated by the formula below.
푅ꢓ × ꢔ푅2 + 푅푆ꢕ푋/ꢆ푁ꢓꢖ+푅2 × 푅푆ꢕ푋/ꢆ푁ꢓ
푉
= Vꢆ푁ꢓ ×
퐼푁_ꢆ푁퐴퐵ꢊꢆ
푅2 × 푅푆ꢕ푋/ꢆ푁ꢓ
[V]
Where:
푉
is the enable voltage at the rise-up of the VIN pin voltage.
퐼푁_ꢆ푁퐴퐵ꢊꢆ
푉ꢆ푁ꢓ is the enable voltage 1.
6.2
Disable Voltage
The disable voltage at the fall of the VIN pin voltage VIN_DISABLE is calculated by the formula below.
푅ꢓ × ꢔ푅2 + 푅푆ꢕ푋/ꢆ푁ꢓ + 푅푆ꢕ푋/ꢆ푁2ꢖ+푅2 × ꢔ푅푆ꢕ푋/ꢆ푁ꢓ + 푅푆ꢕ푋/ꢆ푁2
ꢖ
푉
= Vꢆ푁2 ×
퐼푁_ꢕ퐼푆퐴퐵ꢊꢆ
푅2 × ꢔ푅푆ꢕ푋/ꢆ푁ꢓ + 푅푆ꢕ푋/ꢆ푁2
ꢖ
[V]
푉
is the disable voltage at the fall of the VIN pin voltage.
퐼푁_ꢕ퐼푆퐴퐵ꢊꢆ
푉ꢆ푁2 is the enable voltage 2.
It is necessary to set the duty to DMAX or less and operate in this IC’s control method. So set the disable voltage
at the fall of the VIN pin voltage VIN_DISABLE to meet the condition below.
ꢀ푃
[V]
)
(
× 푉푂푈푇 + 푉퐹
푉
>
퐼푁_ꢕ퐼푆퐴퐵ꢊꢆ
ꢀ푆
Where:
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
푉푂푈푇 is the output voltage.
푉퐹 is the forward voltage at the secondary output diode.
VIN
R1
VIN
RSDX/EX1
SDX/EN
AGND
R2
RSDX/EX2
Figure 46. Position of Resistors Connected to the SDX/EN Pin
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
26/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
7
Minimum Load Current
This IC stables the secondary output voltage isolated with the transformer by the primary flyback voltage at the internal
switching MOSFET turned off. Therefore, it operates with the minimum on time tON_MIN and maximum off time tOFF_MAX
even if the status is light load. By this operation, the output voltage may rise in the case of the low load current
because a little energy is supplied to the secondary output. To prevent the rise of output voltage, secure the minimum
load current with adding such as the dummy resistor RDUMMY
.
The necessary minimum load current IOUT_MIN is calculated by the formula below.
1
ꢃ푂푈푇_푀퐼푁 = ×
ꢉ
ꢔ푉 × 푡푂푁_푀퐼푁ꢖ2
퐼푁
[A]
퐿푃 × 푉푂푈푇 × ꢔ푡푂푁_푀퐼푁 + 푡푂퐹퐹_푀퐴푋
ꢖ
Where:
ꢃ푂푈푇_푀퐼푁 is the minimum output current.
is the VIN pin voltage.
푉
퐼푁
푡푂푁_푀퐼푁 is the minimum on time.
퐿푃 is the primary inductance.
푉푂푈푇 is the output voltage.
푡푂퐹퐹_푀퐴푋 is the maximum off time.
VF
IS
VIN
RDUMMY
NP/NS
SW
VOUT
IRFB
RFB
FB
COMPARATOR
ADAPTIVE
ON-TIME
DRIVER
CONTROLLER
VINTREF
IP
VL_COMP
Current
Monitor
IL_COMP
REF
PGND
L_COMP
RREF
CL_COMP
RL_COMP
Figure 47. Position of RDUMMY
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
27/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
8
Infection Point of Switching Frequency
This IC realizes the efficiency by fluctuating the switching frequency corresponding to the load current at light load.
The load current IOUT_ SW, from which the switching frequency fSW starts to drop, is calculated by the formula below.
f
1
푓
푆푊
× ꢔ푉 × 푡푂푁_푀퐼푁ꢖ2
퐼푁
ꢃ푂푈푇_ 푆푊 = ×
푓
[A]
ꢉ
퐿푃 × 푉푂푈푇
Where:
ꢃ푂푈푇_ 푆푊
푓
is the load current, from which the switching frequency starts to drop.
푓
푉
퐼푁
is the switching frequency.
푆푊
is the VIN pin voltage.
푡푂푁_푀퐼푁 is the minimum on time.
퐿푃 is the primary inductance.
푉푂푈푇 is the output voltage.
In addition, the switching frequency becomes the minimum switching frequency fSW_MIN at the switching operation with
the minimum on time tON_MIN and maximum off time tOFF_MAX and it is calculated by the formula below.
1
푓
=
푆푊_푀퐼푁
[Hz]
푡푂푁_푀퐼푁 + 푡푂퐹퐹_푀퐴푋
Where:
푓
is the minimum switching frequency.
푆푊_푀퐼푁
푡푂퐹퐹_푀퐴푋 is the maximum off time.
Switching Frequency
fSW
fSW_MIN
IOUT
IOUT_MIN IOUT_fSW
Figure 48. Switching Frequency vs IOUT
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
28/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Application Examples – continued
9
Load Compensation Function
The load regulation is worsen by VF and ESR. In the application gotten worse by these factors, it is enable to make
the fluctuation of the output voltage caused by the load current alteration small by using the load compensation function.
In addition to above, short the L_COMP pin to the GND to invalidate this function.
VF
VIN
IS
NP/NS
VOUT
IRFB
RFB
FB
SW
COMPARATOR
VINTREF
ADAPTIVE
ON-TIME
CONTROLLER
DRIVER
IP
VL_COMP
Current
Monitor
IL_COMP
RINTCOMP
L_COMP
REF
RREF
PGND
CL_COMP
RL_COMP
Figure 49. Block Diagram of Load Compensation
tS
SW pin voltage
tON
IP_MAX
IP_MIN
Primary transformer current IP
Primary transformer current IS
Figure 50. Switching Operation or Continuous Mode
Output voltage
with load compensation
without load compensation
Gradient: RVF + ESR
Output Current
Figure 51. Image of Load Compensation
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
29/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
9
Load Compensation Function – continued
9.1
Setting of Amount of Load Compensation
This function compensates the drop of output voltage VOUT corresponding to the average current of primary
transformer current IP.
The amount of load compensation is adjusted by the external capacitor CL_COMP and external resistor RL_COMP at
the L_COMP pin because the primary transformer current IP and secondary transformer current IS have the
relation of the formula below. The reference value of CL_COMP is 0.1 μF.
ꢀ푃
[A]
ꢃ푃 =
× ꢃ푆
ꢀ푆
Where:
ꢃ푃 is the primary transformer current.
ꢀ푃 is the number of winding at the primary transformer.
ꢀ푆 is the number of winding at the secondary transformer.
ꢃ푆 is the secondary transformer current.
9.1.1 Setting of External Resistor at the L_COMP Pin RL_COMP
It is necessary to calculate the L_COMP pin current IL_COMP following the formula below for the setting of
the external resistor at the L_COMP pin RL_COMP
.
푉
ꢊ_ꢗ푂푀푃
[A]
ꢃꢊ_ꢗ푂푀푃
=
푅퐼푁푇ꢗ푂푀푃
Where:
ꢃꢊ_ꢗ푂푀푃 is the L_COMP pin current.
is the L_COMP pin voltage.
푉
ꢊ_ꢗ푂푀푃
푅퐼푁푇ꢗ푂푀푃 is the internal resistor at the L_COMP pin
VL_COMP mentioned in the formula above is the value converted the current which calculated by K x IP flowing
from Current Monitor Block to the L_COMP pin by the external resistor at the L_COMP pin RL_COMP
.
It
becomes IL_COMP in the inside and compensates the REF pin current.
It is necessary to meet VL_COMP ≤ 0.5 V because the operational voltage’s upper limit of VL_COMP is restricted
by the internal circuit.
In addition, Connect the external capacitor at the L_COMP pin CL_COMP because the rapid fluctuation of
IL_COMP may make the VL_COMP unstable.
Than the above, VL_COMP should meet the conditions below.
푉
= 퐾 × 푅ꢊ_ꢗ푂푀푃 × ꢃ푃_퐴ꢘꢆ ≤ 0.5
ꢊ_ꢗ푂푀푃
ꢃ푃_푀퐼푁 + ꢃ푃_푀퐴푋 푡푂푁
= 퐾 × 푅ꢊ_ꢗ푂푀푃
×
×
≤ 0.5
[V]
ꢉ
푡푆
Where:
퐾 is the compressor magnification in Current Monitor Block.
푅ꢊ_ꢗ푂푀푃 is the external resistor at the L_COMP pin.
ꢃ푃_퐴ꢘꢆ is the average value of primary transformer current IP.
ꢃ푃_푀퐼푁 is the minimum value of primary transformer current IP.
ꢃ푃_푀퐴푋 is the maximum value of primary transformer current IP.
푡푆 is the switching cycle.
푡푂푁 is the on time.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
30/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
9.1.1 Setting of External Resistor at the L_COMP Pin RL_COMP – continued
By the load compensation function, the feedback current decreases IL_COMP from its original current value
flowing at RREF
.
As the result, the High level of VSW rises for compensating this drop and it compensates
the dropped output voltage VOUT
.
The output voltage at operating the load compensation function is calculated by the formula below.
ꢀ푆
ꢀ푃
푉ꢅꢆ퐹
푅ꢅꢆ퐹
푉푂푈푇
=
× ꢁ
+ ꢃꢊ_ꢗ푂푀푃ꢂ × 푅퐹퐵 − 푉퐹 − ꢃ푆_퐴ꢘꢆ × 퐸ꢄ푅
[V]
Where:
푉푂푈푇 is the output voltage.
ꢀ푆 is the number of winding at the secondary transformer.
ꢀ푃 is the number of winding at the primary transformer.
푉ꢅꢆ퐹 is the REF pin voltage.
푅ꢅꢆ퐹 is the external resistor between the REF and AGND pins.
ꢃꢊ_ꢗ푂푀푃 is the L_COMP pin current.
푅퐹퐵 is the external resistor between the FB and SW pins.
푉퐹 is the forward voltage at the secondary output diode.
ꢃ푆_퐴ꢘꢆ is the average value of the secondary transformer current IS.
Reference: The output voltage VOUT at normal operation
ꢀ푆 푅퐹퐵
[V]
푉푂푈푇
=
×
× 푉ꢅꢆ퐹 − 푉퐹 − ꢃ푆_퐴ꢘꢆ × 퐸ꢄ푅
ꢀ푃 푅ꢅꢆ퐹
According to the formula above, it is necessary to establish the next formula to remove the forward voltage
at the secondary output diode VF and ESR by the L_COMP pin current IL_COMP
.
ꢀ푆
[A]
ꢃꢊ_ꢗ푂푀푃
×
× 푅퐹퐵 = 푉퐹 + ꢃ푆_퐴ꢘꢆ × 퐸ꢄ푅
ꢀ푃
Next, calculate the RL_COMP by making the linear approximation RVF of the fluctuation of the forward voltage
at the secondary output diode corresponding to the secondary transformer current IS.
퐾 × 푅ꢊ_ꢗ푂푀푃 × ꢃ푃_퐴ꢘꢆ ꢀ푆
×
× 푅퐹퐵 = ꢃ푆_퐴ꢘꢆ × 푅ꢘ퐹 + ꢃ푆_퐴ꢘꢆ × 퐸ꢄ푅
푅퐼푁푇ꢗ푂푀푃
ꢀ푃
2
퐾 × 푅ꢊ_ꢗ푂푀푃
푅퐼푁푇ꢗ푂푀푃
ꢀ푆
1 − 퐷푢푡푦
(
)
× ꢁ ꢂ × 푅퐹퐵 = 푅ꢘ퐹 + 퐸ꢄ푅 ×
ꢀ푃
퐷푢푡푦
Than the above,
2
푅ꢘ퐹 + 퐸ꢄ푅
퐾 × 푅퐹퐵
ꢀ푆
× ꢁ ꢂ ×
ꢀ푃
1 − 퐷푢푡푦
퐷푢푡푦
푅ꢊ_ꢗ푂푀푃 = 푅퐼푁푇ꢗ푂푀푃
×
[Ω]
Where:
퐾 is the compressor magnification in Current Monitor Block.
푅ꢊ_ꢗ푂푀푃 is the external resistor at the L_COMP pin.
ꢃ푃_퐴ꢘꢆ is the average value of primary transformer current IP.
푅퐼푁푇ꢗ푂푀푃 is the internal resistor at the L_COMP pin
The values of RVF, ESR, and RFB depend on the operating environment such as use parts and mounting
boards. When set the RL_COMP actually, adjust them monitoring the output voltage VOUT in the range of
using load current certainly.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
31/38
20.Mar.2023 Rev.002
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
I/O Equivalence Circuit
1
AGND
2
SDX/EN
3
L_COMP
4
REF
Internal
Supply
VIN
REF
SDX/EN
L_COMP
AGND
AGND
AGND
AGND
SW
VIN
5
FB
6
7
8
PGND
SW
VIN
PGND
AGND
FB
AGND
AGND
PGND
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
32/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Operational Notes
1.
2.
Reverse Connection of Power Supply
Connecting the power supply in reverse polarity can damage the IC. Take precautions against reverse polarity when
connecting the power supply, such as mounting an external diode between the power supply and the IC’s power supply
pins.
Power Supply Lines
Design the PCB layout pattern to provide low impedance supply lines. Furthermore, connect a capacitor to ground at
all power supply pins. Consider the effect of temperature and aging on the capacitance value when using electrolytic
capacitors.
3.
4.
Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient condition.
Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed separately but
connected to a single ground at the reference point of the application board to avoid fluctuations in the small-signal
ground caused by large currents. Also ensure that the ground traces of external components do not cause variations
on the ground voltage. The ground lines must be as short and thick as possible to reduce line impedance.
5.
6.
Recommended Operating Conditions
The function and operation of the IC are guaranteed within the range specified by the recommended operating
conditions. The characteristic values are guaranteed only under the conditions of each item specified by the electrical
characteristics.
Inrush Current
When power is first supplied to the IC, it is possible that the internal logic may be unstable and inrush current may flow
instantaneously due to the internal powering sequence and delays, especially if the IC has more than one power supply.
Therefore, give special consideration to power coupling capacitance, power wiring, width of ground wiring, and routing
of connections.
7.
Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output pin may subject
the IC to stress. Always discharge capacitors completely after each process or step. The IC’s power supply should
always be turned off completely before connecting or removing it from the test setup during the inspection process. To
prevent damage from static discharge, ground the IC during assembly and use similar precautions during transport and
storage.
8.
9.
Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting may result in
damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power supply and output pin.
Inter-pin shorts could be due to many reasons such as metal particles, water droplets (in very humid environment) and
unintentional solder bridge deposited in between pins during assembly to name a few.
Unused Input Pins
Input pins of an IC are often connected to the gate of a MOS transistor. The gate has extremely high impedance and
extremely low capacitance. If left unconnected, the electric field from the outside can easily charge it. The small charge
acquired in this way is enough to produce a significant effect on the conduction through the transistor and cause
unexpected operation of the IC. So unless otherwise specified, unused input pins should be connected to the power
supply or ground line.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
33/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Operational Notes – continued
10. Regarding the Input Pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them
isolated. P-N junctions are formed at the intersection of the P layers with the N layers of other elements, creating a
parasitic diode or transistor. For example (refer to figure below):
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes inevitably occur in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Therefore, conditions that cause these diodes to
operate, such as applying a voltage lower than the GND voltage to an input pin (and thus to the P substrate) should be
avoided.
Resistor
Transistor (NPN)
Pin A
Pin B
Pin B
B
E
C
Pin A
B
C
E
P
P+
P+
N
P+
P
P+
N
N
N
N
N
N
N
Parasitic
Elements
Parasitic
Elements
P Substrate
GND GND
P Substrate
GND
GND
Parasitic
Elements
Parasitic
Elements
N Region
close-by
Figure 52. Example of Monolithic IC Structure
11. Ceramic Capacitor
When using a ceramic capacitor, determine a capacitance value considering the change of capacitance with
temperature and the decrease in nominal capacitance due to DC bias and others.
12. Thermal Shutdown Circuit (TSD)
This IC has a built-in thermal shutdown circuit that prevents heat damage to the IC. Normal operation should always
be within the IC’s maximum junction temperature rating. If however the rating is exceeded for a continued period, the
junction temperature (Tj) will rise which will activate the TSD circuit that will turn OFF power output pins. When the Tj
falls below the TSD threshold, the circuits are automatically restored to normal operation.
Note that the TSD circuit operates in a situation that exceeds the absolute maximum ratings and therefore, under no
circumstances, should the TSD circuit be used in a set design or for any purpose other than protecting the IC from heat
damage.
13. Over Current Protection Circuit (OCP)
This IC incorporates an integrated overcurrent protection circuit that is activated when the load is shorted. This
protection circuit is effective in preventing damage due to sudden and unexpected incidents. However, the IC should
not be used in applications characterized by continuous operation or transitioning of the protection circuit.
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
34/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Ordering Information
B D 7
J
2
0
0
x
x
x
x
-
L B x x
Production Line
NONE:Production Line A
U:Production Line B
Package
HFN: HSON8
EFJ: HTSOP-J8
Product Class
LB for Industrial Applications
Packaging and Forming Specification
TR: Embossed Tape and Reel (HSON8)
E2: Embossed Tape and Reel (HTSOP-J8)
Lineup
Product Name
Part Number Marking
Orderable Part Number
Package
Remarks
-
BD7J200HFN-LB
BD7J200EFJ-LB
BD7J200UEFJ-LB
D7J200
D7J200
U7J200
BD7J200HFN-LBTR
BD7J200EFJ-LBE2
BD7J200UEFJ-LBE2
HSON8
Production Line A(Note 1)
Production Line B(Note 1)
HTSOP-J8
HTSOP-J8
(Note 1) For the purpose of improving production efficiency, Production Line A and B have a multi-line configuration.
Electrical characteristics noted in Datasheet does not differ between Production Line A and B.
Production Line B is recommended for new product.
Marking Diagrams
HTSOP-J8 (TOP VIEW)
HSON8 (TOP VIEW)
Part Number Marking
LOT Number
Part Number Marking
LOT Number
Pin 1 Mark
Pin 1 Mark
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
35/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Physical Dimension and Packing Information
Package Name
HSON8
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
36/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Physical Dimension and Packing Information – continued
Package Name
HTSOP-J8
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
37/38
BD7J200HFN-LB BD7J200EFJ-LB BD7J200UEFJ-LB
Revision History
Date
Revision
Changes
001
002
New Release
20.Aug.2019
20.Mar.2023
Add BD7J200UEFJ-LB
www.rohm.com
© 2018 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0F1F0BZ00010-1-2
20.Mar.2023 Rev.002
38/38
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号:
BD7J200HFN-LB
本产品是面向工业设备市场的产品,保证可长期稳定供货。适合用于工业设备的绝缘电源。本产品是无需光电耦合器的绝缘型反激式转换器。无需以往用途中为获得稳定输出电压所需的光电耦合器、变压器3次绕组构成的反馈电路。还采用了独创的适应型导通时间控制技术,不需要外接相位补偿部件,可大幅减少部件个数,并实现小型、高可靠性的绝缘型电源应用设计。
ROHM
BD7J201EFJ-LB
本产品是能够保证向工业设备市场长期供应的产品,是不需要光耦的隔离型反激式转换器。使用本产品,将不再需要以往应用中为了获得稳定的输出电压而需要的由光电耦合器或变压器辅助绕组组成的反馈电路。此外,通过采用ROHM自有的自适应导通时间控制技术,也不再需要外置相位补偿器件,从而可以使隔离式电源设计所需的元器件数量显著减少,并且能够实现小型化和更高可靠性。
ROHM
BD7J201HFN-LB
本产品是能够保证向工业设备市场长期供应的产品,是不需要光耦的隔离型反激式转换器。使用本产品,将不再需要以往应用中为了获得稳定的输出电压而需要的由光电耦合器或变压器辅助绕组组成的反馈电路。此外,通过采用ROHM自有的自适应导通时间控制技术,也不再需要外置相位补偿器件,从而可以使隔离式电源设计所需的元器件数量显著减少,并且能够实现小型化和更高可靠性。
ROHM
BD7LS00G-C
BD7LS00G-C是适用于车载应用的Single 2-input NAND gate。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS02G-C
BD7LS02G-C是适用于车载应用的Single 2-input NOR gate。可保证在1.65V到5.5V的电源电压下工作。具有输出容错电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS04G-C
BD7LS04G-C是适用于车载应用的Single Inverter。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS07G-C
BD7LS07G-C是适用于车载应用的Single Buffer with Open-drain。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS08G-C
BD7LS08G-C是适用于车载应用的Single 2-input AND gate。可保证在1.65V到5.5V的电源电压下工作。具有输出容错电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS125G-C
BD7LS125G-C是适用于车载应用的Single 3-state Buffer。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS14G-C
BD7LS14G-C是适用于车载应用的Single Schmitt Trigger Inverter。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS17G-C
BD7LS17G-C是适用于车载应用的Single Schmitt Trigger Buffer。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
BD7LS32G-C
BD7LS32G-C是适用于车载应用的Single 2-input OR gate。可保证在1.65V到5.5V的电源电压下工作。具备output tolerant电路,可在断电时防止电流从连接对象流入,保护输出电路。
ROHM
©2020 ICPDF网 联系我们和版权申明