BD89630EFJ-E2 [ROHM]
Switching Regulator, Current-mode, 2A, 1000kHz Switching Freq-Max, PDSO8, 4.90 X 6 MM, 1 MM HEIGHT, ROHS COMPLIANT, HTSOP-8;
| 型号： | BD89630EFJ-E2 |
| 厂家： | 
ROHM |
| 描述： | Switching Regulator, Current-mode, 2A, 1000kHz Switching Freq-Max, PDSO8, 4.90 X 6 MM, 1 MM HEIGHT, ROHS COMPLIANT, HTSOP-8 开关 光电二极管 输出元件 |
| 文件： | 总24页 (文件大小：625K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
2.7V to 5.5V, 2A 1ch
Synchronous Buck Converter integrated FET
BD89630EFJ
●General Description
●Key Specification
ROHM’s high efficiency step-down switching regulator
BD89630EFJ is a power supply designed to produce a
low voltage including 1 volts from 5.5/3.3 volts power
supply line. Offers high efficiency with synchronous
rectifier. Employs a current mode control system to
provide faster transient response to sudden change in
load.
Input voltage range:
Output voltage range:
Average output Current:
Switching frequency:
Pch FET ON resistance:
Nch FET ON resistance:
Standby current:
2.7V to 5.5V
1.0V to 2.5V
2A(Max.)
1MHz(Typ.)
145mΩ(Typ.)
80mΩ(Typ.)
5μA (Typ.)
Operating temperature range:
-25℃ to +85℃
●Features
Offers fast transient response with current mode
PWM control system.
●Package
HTSOP-J8
(Typ.)
(Typ.)
(Max.)
Offers highly efficiency for all load range with
synchronous rectifier (Nch/Pch FET)
Incorporates soft-start function.
Incorporates thermal protection and ULVO
functions.
4.90mm x 6.00mm x 1.00mm
Incorporates short-current protection circuit with
time delay function.
Incorporates shutdown function
●Applications
Power supply for LSI including DSP, Micro computer
and ASIC
HTSOP-J8
●Typical Application Circuit
Cin
L
VCC
VCC
EN
SW
VOUT
ADJ
RFB1
VADJ
COMP
VADJ
GND
CO
RCOMP
RFB2
CCOMP
Fig.1 Typical Application Circuit
○Product structure：Silicon monolithic integrated circuit ○This product is not designed protection against radioactive rays.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･14･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
1/21
Daattaasshheeeett
BD89630EFJ
●Pin configuration(TOP VIEW)
COMP
ADJ
N.C
GND
EN
SW
SW
VCC
Fig.2 Pin configuration
●Pin Description
Pin No.
Pin name
COMP
GND
EN
PIN function
1
2
3
4
5
6
7
8
GmAmp output pin/Connected phase compensation capacitor
Ground
Enable pin(Active High, Open Active)
VCC power supply input pin
Pch/Nch FET drain output pin
Pch/Nch FET drain output pin
Non Connect
VCC
SW
SW
N.C
ADJ
Output voltage detect pin
●Block Diagram
VCC
SW
SW
GND
Fig.3 Block Diagram
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
2/21
Daattaasshheeeett
BD89630EFJ
●Absolute Maximum Ratings
Symbol
Ratings
Unit
Parameter
VCC Voltage
VCC
VEN
-0.3 to +7 *1
-0.3 to +7
-0.3 to +7
0.5*2
V
V
EN Voltage
SW,COMP Voltage
VSW,VCOMP
Pd1
V
Power Dissipation 1
Power Dissipation 2
Operating temperature range
Storage temperature range
Maximum junction temperature
W
W
℃
℃
℃
Pd2
3.76*3
Topr
-25 to +85
-55 to +150
+150
Tstg
Tjmax
*1
*2
*3
Pd should not be exceeded.
Reduced by 4.0mW for increase in Ta of 1℃ above 25℃.
Reduced by 30.0mW for increase in Ta of 1℃ above 25℃.
(when mounted on a board 70.0mm × 70.0mm × 1.6mm Glass-epoxy PCB)
●Recommended Operating Ratings (Ta=-25 to +85℃)
Ratings
Parameter
Symbol
Unit
Min.
2.7 *5
0
Typ.
Max.
5.5
Power Supply Voltage
EN Voltage
VCC
VEN
VOUT
Isw
5.0
V
V
V
A
-
-
-
Vcc
Output voltage range
SW average output current
1.0
-
2.5*4
2.0*5
*4
*5
In case set output voltage 1.6V or more, VccMin. = Vout +2.25V
Pd should not be exceeded.
●Electrical Characteristics (Unless otherwise specified , Ta=25℃ VCC=5V, EN=VCC, R1=20kΩ, R2=7.5kΩ)
Limit
Parameter
Symbol
Unit
Conditions
Min.
Typ.
5
Max.
20
Standby Current
ISTB
ICC
-
µA
µA
V
EN=GND
Bias Current
-
350
GND
VCC
1.25
1
600
0.3
-
EN Low Voltage
VENL
VENH
IEN
-
2.0
-
Stand-by Mode
Active Mode
VEN=5V
EN High Voltage
V
EN Current
10
µA
MHz
Oscillation Frequency
Pch FET ON Resistance
Nch FET ON Resistance
ADJ Reference Voltage
COMP SINK Current
COMP Source Current
UVLO Threshold Voltage
UVLO Hysteresis Voltage
Soft Start Time
FOSC
RONP
RONN
VADJ
0.8
-
1.2
290
160
0.812
-
145
80
mΩ VCC=5V
mΩ VCC=5V
V
-
0.788
10
0.800
25
ICOSI
ICOSO
VUVLO1
VUVLO2
TSS
µA
µA
V
VADJ=1.0V
10
25
-
VADJ=0.6V
2.400
2.425
0.5
1
2.500
2.550
1
2.600
2.700
2
Vcc=5V→0V
Vcc=0V→5V
V
ms
ms
V
Timer Latch Time
TLATCH
VSCP
2
4
Output Short circuit Threshold Voltage
-
VOUT×0.5 VOUT×0.7
VOUT=1.0V→0V
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
3/21
Daattaasshheeeett
BD89630EFJ
●Typical Performance Curves
Fig.5 VEN-Vout
Fig.4 Vcc-Vout
Fig. 7 Ta-VOUT
Fig.6 IOUT-VOUT
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
4/21
Daattaasshheeeett
BD89630EFJ
100
【VOUT=1.1V】
90
80
70
60
50
40
30
20
10
0
VCC=5.0V
Ta=25℃
10
100
1000
10000
OUTPUT CURRENT:IOUT[mA]
Fig.8 Efficiency
Fig.9 Ta-FOSC
Fig.11 Ta-VEN
Fig.10 Ta-RONN, RONP
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
5/21
Daattaasshheeeett
BD89630EFJ
Fig.12 Ta-ICC
Fig.13 Vcc-FOSC
Fig.15 SW waveform Io=10mA
Fig.14 Soft start waveform
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
6/21
Daattaasshheeeett
BD89630EFJ
Fig. 16 Transient response
Fig. 17 Transient response
Io=0.5A→1.5A(10µs)
Io=1.5A→0.5A(10µs)
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
7/21
Daattaasshheeeett
BD89630EFJ
Application Information
●Operation
○Synchronous rectifier
It does not require the power to be dissipated by a rectifier externally connected to a conventional DC/DC converter IC,
and its P.N junction shoot-through protection circuit limits the shoot-through current during operation, by which the
power dissipation of the set is reduced.
○Current mode PWM control
Synthesizes a PWM control signal with a inductor current feedback loop added to the voltage feedback.
・PWM (Pulse Width Modulation) control
The oscillation frequency for PWM is 1 MHz. SET signal form OSC turns ON a P-channel MOS FET (while a
N-channel MOS FET is turned OFF), and an inductor current IL increases. The current comparator (Current Comp)
receives two signals, a current feedback control signal (SENSE: Voltage converted from IL) and a voltage feedback
control signal (FB), and issues a RESET signal if both input signals are identical to each other, and turns OFF the
P-channel MOS FET (while a N-channel MOS FET is turned ON) for the rest of the fixed period. The PWM control
repeat this operation.
SENSE
Current
Comp
VOUT
RESET
R
S
Q
IL
Level
Shift
FB
SET
Driver
Logic
VOUT
Gm Amp.
SW
Load
OSC
COMP
Fig.18 Diagram of current mode PWM control
PVCC
Current
Comp
Current
Comp
SENSE
FB
SET
SET
GND
GND
GND
RESET
SW
RESET
SW
IL
IL(AVE)
VOUT
VOUT
VOUT(AVE)
Fig.19 PWM switching timing chart
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
8/21
Daattaasshheeeett
BD89630EFJ
●Description of operations
・Soft-start function
EN terminal shifted to “High” activates a soft-starter to gradually establish the output voltage with the current limited
during startup, by which it is possible to prevent an overshoot of output voltage and an inrush current.
・Shutdown function
With EN terminal shifted to “Low”, the device turns to Standby Mode, and all the function blocks including reference
voltage circuit, internal oscillator and drivers are turned to OFF. Circuit current during standby is 5µA (Typ.).
・UVLO function
Detects whether the input voltage sufficient to secure the output voltage of this IC is supplied. And the hysteresis width
of 50mV (Typ.) is provided to prevent output chattering.
Hysteresis 50mV
VCC
EN
VOUT
Tss
Tss
Tss
Soft start
Standby
mode
Standby
mode
Standby mode
Operating mode
Operating mode
Operating mode
Standby mode
UVLO
EN
UVLO
UVLO
Fig.20 Soft start, Shutdown, UVLO timing chart
・Short-current protection circuit with time delay function
Turns OFF the output to protect the IC from breakdown when the incorporated current limiter is activated continuously for
the fixed time(TLATCH) or more. The output thus held tuned OFF may be recovered by restarting EN or by
re-unlocking UVLO.
EN
Output OFF
latch
Output Short circuit
Threshold Voltage
VOUT
IL Limit
IL
t1<TLATCH
t2=TLATCH
Standby
mode
Standby
mode
Operating mode
Operating mode
EN
Timer latch
EN
Fig.21 Short-current protection circuit with time delay timing chart
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
9/21
Daattaasshheeeett
BD89630EFJ
●Information on advantages
Advantage 1 : Offers fast transient response with current mode control system.
BD89630EFJ (Load response IO= 0.5A→1.5A)
Conventional product (Load response IO= 0.5A→1.5A)
VOUT
VOUT
36mV
75mV
IOUT
IOUT
Voltage drop due to sudden change in load was reduced by about 50%.
Fig.22 Comparison of transient response
Advantage 2 : Offers high efficiency with synchronous rectifier
Utilizes the synchronous rectifying mode and the low on-resistance MOS FETs incorporated as power transistor.
ON resistance of P-channel MOS FET : 145mΩ(Typ.)
ON resistance of N-channel MOS FET : 80mΩ(Typ.)
100
90
80
70
60
50
40
30
【VOUT=1.1V】
20
10
0
VCC=5.0V
Ta=25℃
10
Advantage 3 :・Supplied in smaller package due to small-sized power MO
・Output capacitor Co required for current mode control: 10µF ceramic capacitor
・Inductance L required for the operating frequency of 1 MHz: 1.5µH inductor
100
1000
10000
OUTPUT CURRENT:IOUT[mA]
Reduces a mounting area required.
VCC
15mm
CIN
Cin
RCOMP
L
DC/DC
Convertor
Controller
L
VOUT
10mm
CCOMP
RCOMP
CCOMP
Co
CO
Fig.24 Example application
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
10/21
Daattaasshheeeett
BD89630EFJ
●Switching regulator efficiency
Efficiency ŋ may be expressed by the equation shown below:
VOUT×IOUT
Vin×Iin
POUT
Pin
POUT
η=
×100[%]=
×100[%]=
×100[%]
POUT+PDα
Efficiency may be improved by reducing the switching regulator power dissipation factors PDα as follows:
Dissipation factors:
1) ON resistance dissipation of inductor and FET：PD(I2R)
2) Gate charge/discharge dissipation：PD(Gate)
3) Switching dissipation：PD(SW)
4) ESR dissipation of capacitor：PD(ESR)
5) Operating current dissipation of IC：PD(IC)
2
1)PD(I2R)=IOUT ×(RCOIL+RON) (RCOIL[Ω]：DC resistance of inductor, RON[Ω]：ON resistance of FET, IOUT[A]：Output
current.)
2)PD(Gate)=Cgs×f×V2 (Cgs[F]：Gate capacitance of FET, f[Hz]：Switching frequency, V[V]：Gate driving voltage of FET)
Vin2×CRSS×IOUT×f
3)PD(SW)=
(CRSS[F]：Reverse transfer capacitance of FET, IDRIVE[A]：Peak current of gate.)
IDRIVE
2
4)PD(ESR)=IRMS ×ESR (IRMS[A]：Ripple current of capacitor, ESR[Ω]：Equivalent series resistance.)
5)PD(IC)=Vin×ICC (ICC[A]：Circuit current.)
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
11/21
Daattaasshheeeett
BD89630EFJ
●Consideration on permissible dissipation and heat generation
As this IC functions with high efficiency without significant heat generation in most applications, no special consideration is
needed on permissible dissipation or heat generation. In case of extreme conditions, however, including lower input
voltage, higher output voltage, heavier load, and/or higher temperature, the permissible dissipation and/or heat
generation must be carefully considered.
For dissipation, only conduction losses due to DC resistance of inductor and ON resistance of FET are considered.
Because the conduction losses are considered to play the leading role among other dissipation mentioned above
including gate charge/discharge dissipation and switching dissipation.
4
①
IC only
θj-a=249.5℃/W
P=IOUT2×RON
RON=D×RONP+(1-D)RONN
⑤3.76W
②1 layers（copper foil area:0mm×0mm）
θj-a=153.2℃/W
③2 layers（copper foil area:15mm×15mm）
θj-a=113.6℃/W
④2 layers（copper foil area:70mm×70mm）
θj-a=59.2℃/W
⑤4 layers（copper foil area:70mm×70mm）
θj-a=33.3℃/W
D：ON duty (=VOUT/VCC)
RCOIL：DC resistance of coil
RONP：ON resistance of P-channel MOS FET
RONN：ON resistance of N-channel MOS FET
IOUT：Output current
3
2
1
0
(when mounted on a board 70mm×70mm×1.6mm
Glass-epoxy PCB with termal Via)
④2.11W
③1.10W
②0.82W
①0.50W
0
25
50
75 85
100
125
150
Ambient temperature:Ta [℃]
Fig.25 Thermal derating curve
(HTSOP-J8)
Ex.)VCC=5V, VOUT=1.1V, RONP=0.145Ω, RONN=0.08Ω
IOUT=2A, for example,
D=VOUT/VCC=1.1/5=0.22
RON=0.22×0.145+(1-0.22)×0.08
=0.0319+0.0624
=0.0943[Ω]
P=22×0.0943=0.3772[W]
As RONP is greater than RONN in this IC, the dissipation increases as the ON duty becomes greater.
With the consideration on the dissipation as above, thermal design must be carried out with sufficient margin allowed.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
12/21
Daattaasshheeeett
BD89630EFJ
●Selection of components externally connected
1. Selection of inductor (L)
The inductance significantly depends on output ripple current.
As seen in the equation (1), the ripple current decreases as the
inductor and/or switching frequency increases.
IL
ΔIL
VCC
(VCC-VOUT)×VOUT
ΔIL=
[A]・・・(1)
L×VCC×f
IL
Appropriate ripple current at output should be 20% more or less of
the maximum output current.
VOUT
L
ΔIL=0.2×IOUTmax. [A]・・・(2)
(VCC-VOUT)×VOUT
Co
L=
[H]・・・(3)
ΔIL×VCC×f
(ΔIL: Output ripple current, and f: Switching frequency)
Fig.26 Output ripple current
*Current exceeding the current rating of the inductor results in magnetic saturation of the inductor, which decreases
efficiency. The inductor must be selected allowing sufficient margin with which the peak current may not exceed its
current rating.
If VCC=5V, VOUT=1.1V, f=1MHz, ΔIL=0.2×2A=0.4A, for example,(BD89630EFJ)
(5-1.1)×1.1
L=
=2.1µ → 2.2[µH]
0.4×5×1M
*Select the inductor of low resistance component (such as DCR and ACR) to minimize dissipation in the inductor for
better efficiency.
2. Selection of output capacitor (CO)
Output capacitor should be selected with the consideration on the stability region
and the equivalent series resistance required to smooth ripple voltage.
VCC
Output ripple voltage is determined by the equation (4)：
VOUT
ΔVOUT=ΔIL×ESR [V]・・・(4)
L
ESR
Co
(ΔIL: Output ripple current, ESR: Equivalent series resistance of output capacitor)
*Rating of the capacitor should be determined allowing sufficient margin against
output voltage. A 10µF to 100µF ceramic capacitor is recommended.
Less ESR allows reduction in output ripple voltage.
Fig.27 Output capacitor
3. Selection of input capacitor (Cin)
Input capacitor to select must be a low ESR capacitor of the capacitance
sufficient to cope with high ripple current to prevent high transient voltage. The
ripple current IRMS is given by the equation (5):
VCC
Cin
√
VOUT(VCC-VOUT)
VOUT
IRMS=IOUT×
[A]・・・(5)
VCC
L
Co
< Worst case > IRMS(max.)
IOUT
2
When Vcc is twice the VOUT, IRMS=
If VCC=5V, VOUT=1.1V, and IOUTmax.= 2A, (BD89630EFJ)
Fig.28 Input capacitor
√
1.1×(5-1.1)
IRMS=2×
=0.828[ARMS]
5
A low ESR 22µF/10V ceramic capacitor is recommended to reduce ESR dissipation of input capacitor for better efficiency.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
13/21
2012.08.28 Rev.001
Daattaasshheeeett
BD89630EFJ
4. Determination of RCOMP, CCOMP that works as a phase compensator
As the Current Mode Control is designed to limit a inductor current, a pole (phase lag) appears in the low frequency area
due to a CR filter consisting of a output capacitor and a load resistance, while a zero (phase lead) appears in the
high frequency area due to the output capacitor and its ESR. So, the phases are easily compensated by adding a
zero to the power amplifier output with C and R as described below to cancel a pole at the power amplifier.
fp(Min.)
1
A
0
fp=
2π×RO×CO
fp(Max.)
Gain
[dB]
1
fz(ESR)=
fz(ESR)
2π×ESR×CO
IOUTMin.
IOUTMax.
Pole at power amplifier
When the output current decreases, the load resistance Ro
increases and the pole frequency lowers.
0
Phase
[deg]
-90
1
fp(Min.)=
fp(Max.)=
[Hz]←with lighter load
2π×ROMax.×CO
Fig.29 Open loop gain characteristics
1
[Hz] ←with heavier load
2π×ROMin.×CO
A
fz(Amp.)
Zero at power amplifier
Gain
[dB]
Increasing capacitance of the output capacitor lowers the pole
frequency while the zero frequency does not change. (This is
because when the capacitance is doubled, the capacitor ESR
reduces to half.)
0
0
Phase
[deg]
1
fz(Amp.)=
-90
2π×RITH×CITH
Fig.30 Error amp phase compensation characteristics
Cin
L
VCC
VCC
EN
SW
VOUT
VADJ
ADJ
RFB
RFB
VADJ
COMP
GND
CO
RCOMP
CCOMP
Fig.31 Typical application
Stable feedback loop may be achieved by canceling the pole fp (Min.) produced by the output capacitor and the load
resistance with CR zero correction by the error amplifier.
fz(Amp.)= fp(Min.)
1
1
=
2π×RCOMP×CCOMP
2π×ROMax.×CO
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
14/21
Daattaasshheeeett
BD89630EFJ
5. Determination of output voltage
The output voltage VOUT is determined by the equation (6):
VOUT=(R2/R1+1)×VADJ・・・(6) VADJ: Voltage at ADJ terminal (0.8V Typ.)
With R1 and R2 adjusted, the output voltage may be determined as required.
5
6
L
Output
R2
SW
Co
8
Adjustable output voltage range : 1.0V to 2.5V
ADJ
R1
Fig.32 Determination of output voltage
Use 1 kΩ to 100 kΩ resistor for R1. If a resistor of the resistance higher than 100 kΩ is used, check the assembled set
carefully for ripple voltage etc.
The lower limit of input voltage depends on the output voltage.
Basically, it is recommended to use in the condition :
VCCmin = VOUT+2.25V.
4.7
Fig.33. shows the necessary output current value at the lower limit of
input voltage. (DCR of inductor : 0.05Ω)
This data is the characteristic value, so it’ doesn’t guarantee the
operation range,
Vo=2.5V
4.2
3.7
Vo=2.0V
3.2
Vo=1.8V
2.7
0
0.5
1
1.5
2
Outcurrent : Iout [A]
Fig.33 minimum input voltage in each output voltage
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
15/21
Daattaasshheeeett
BD89630EFJ
●Cautions on PC Board layout
VCC
L1
5
6
①
①
①,③
4
SW
Vout
VCC
3
2
C3
①,③
SW
N.C
ADJ
EN
GND
②,④
7
8
②,④
R2
1
COMP
R3
C1
C2
R1
⑥
①,③
⑤
Fig.34 Layout diagram
①To avoid conduction loss, please keep Black thick line as short and thick as possible.
②Don't close to switching current loop.
③Close to IC pin as possible.
④Keep PCB trace as short as possible.
⑤Use single point ground structure to connect with Pin2.
⑥Close to C2 as possible.
※
HTSOP-J8 (BD89630EFJ) has thermal PAD on the reverse of the package.
The package thermal performance may be enhanced by bonding the PAD to GND plane which take a large area
of PCB.
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
16/21
2012.08.28 Rev.001
Daattaasshheeeett
BD89630EFJ
Top Silkscreen Overlay
Top Layer
Middle Layer
Bottom Layer
Bottom Silkscreen Overlay
Fig.35 Reference PCB Layout Pattern
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
17/21
Daattaasshheeeett
BD89630EFJ
●Recommended components Lists on above application
Symbol
L
Part
Coil
Value
1.5µH
Manufacturer
Series
TDK
Kyocera
Kyocera
Kyocera
Murata
Murata
Murata
Murata
Murata
Murata
Rohm
VLC6045T-1R5N
Vcc-VOUT>3V
Vcc-VOUT<3V
10µF
10µF
22µF
CM316X5R106M10A
CM32X5R226M10A
CM316X5R106M10A
GRM18 Series
GRM18 Series
GRM18 Series
GRM18 Series
GRM18 Series
GRM18 Series
MCR03 Series
MCR03 Series
MCR03 Series
MCR03 Series
MCR03 Series
MCR03 Series
CIN
CO
Ceramic capacitor
Ceramic capacitor
VOUT=1.0V
VOUT=1.1V
VOUT=1.2V
VOUT=1.5V
VOUT=1.8V
VOUT=2.5V
VOUT=1.0V
VOUT=1.1V
VOUT=1.2V
VOUT=1.5V
VOUT=1.8V
VOUT=2.5V
330pF
330pF
330pF
390pF
390pF
390pF
2kΩ
CCOMP Ceramic capacitor
2kΩ
Rohm
2.4kΩ
2.4kΩ
3.6kΩ
5.6kΩ
Rohm
RCOMP Resistance
Rohm
Rohm
Rohm
* The parts list presented above is an example of recommended parts. Although the parts are sound, actual circuit
characteristics should be checked on your application carefully before use. Be sure to allow sufficient margins to
accommodate variations between external devices and this IC when employing the depicted circuit with other circuit
constants modified. Both static and transient characteristics should be considered in establishing these margins.
●I/O equivalence circuit
【BD89630EFJ】
・SW pin
・EN pin
VCC
VCC
VCC
EN
SW
・COMP pin
・ADJ pin
VCC
ADJ
COMP
Fig.36 I/O equivalence circuit
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
18/21
Daattaasshheeeett
BD89630EFJ
●Operational Notes
1. Absolute Maximum Ratings
While utmost care is taken to quality control of this product, any application that may exceed some of the absolute
maximum ratings including the voltage applied and the operating temperature range may result in breakage. If broken,
short-mode or open-mode may not be identified. So if it is expected to encounter with special mode that may exceed the
absolute maximum ratings, it is requested to take necessary safety measures physically including insertion of fuses.
2. Electrical potential at GND
GND must be designed to have the lowest electrical potential In any operating conditions.
3. Short-circuiting between terminals, and mismounting
When mounting to pc board, care must be taken to avoid mistake in its orientation and alignment. Failure to do so may
result in IC breakdown. Short-circuiting due to foreign matters entered between output terminals, or between output and
power supply or GND may also cause breakdown.
4. Operation in Strong electromagnetic field
Be noted that using the IC in the strong electromagnetic radiation can cause operation failures.
5. Thermal shutdown protection circuit
Thermal shutdown protection circuit is the circuit designed to isolate the IC from thermal runaway, and not intended to
protect and guarantee the IC. So, the IC the thermal shutdown protection circuit of which is once activated should not
be used thereafter for any operation originally intended.
6. Inspection with the IC set to a pc board
If a capacitor must be connected to the pin of lower impedance during inspection with the IC set to a pc board, the
capacitor must be discharged after each process to avoid stress to the IC. For electrostatic protection, provide proper
grounding to assembling processes with special care taken in handling and storage. When connecting to jigs in the
inspection process, be sure to turn OFF the power supply before it is connected and removed.
7. Input to IC terminals
This is a monolithic IC with P+ isolation between P-substrate and each element as illustrated below. This P-layer and
the N-layer of each element form a P-N junction, and various parasitic element are formed.
If a resistor is joined to a transistor terminal as shown in Fig 37.
○P-N junction works as a parasitic diode if the following relationship is satisfied;
GND>Terminal A (at resistor side), or GND>Terminal B (at transistor side); and
○if GND>Terminal B (at NPN transistor side),
a parasitic NPN transistor is activated by N-layer of other element adjacent to the above-mentioned parasitic diode.
The structure of the IC inevitably forms parasitic elements, the activation of which may cause interference among circuits,
and/or malfunctions contributing to breakdown. It is therefore requested to take care not to use the device in such
manner that the voltage lower than GND (at P-substrate) may be applied to the input terminal, which may result in
activation of parasitic elements.
Resistor
Transistor (NPN)
B
Pin A
Pin B
Pin B
C
E
Pin A
B
C
E
N
N
N
P+
P+
P+
P+
N
P
P
N
N
Parasitic
element
Parasitic
element
P substrate
P substrate
GND
GND
GND
GND
Parasitic element
Parasitic element
Other adjacent elements
Fig.37 Simplified structure of monorisic IC
8. Ground wiring pattern
If small-signal GND and large-current GND are provided, It will be recommended to separate the large-current GND
pattern from the small-signal GND pattern and establish a single ground at the reference point of the set PCB so that
resistance to the wiring pattern and voltage fluctuations due to a large current will cause no fluctuations in voltages of the
small-signal GND. Pay attention not to cause fluctuations in the GND wiring pattern of external parts as well.
9. Selection of inductor
It is recommended to use an inductor with a series resistance element (DCR) 0.1Ω or less. Especially, in case output
voltage is set 1.6V or more, note that use of a high DCR inductor will cause an inductor loss, resulting in decreased
output voltage. Should this condition continue for a specified period (soft start time + timer latch time), output short circuit
protection will be activated and output will be latched OFF. When using an inductor over 0.1Ω, be careful to ensure
adequate margins for variation between external devices and this IC, including transient as well as static characteristics.
Furthermore, in any case, it is recommended to start up the output with EN after supply voltage is within operation range.
Status of this document
The Japanese version of this document is formal specification. A customer may use this translation version only for a reference
to help reading the formal version.
If there are any differences in translation version of this document formal version takes priority
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
19/21
2012.08.28 Rev.001
Daattaasshheeeett
BD89630EFJ
●Ordering Information
B D 8 9 6 3 0 E F
J
-
E 2
Package
EFJ: HTSOP-J8
Packaging and forming specification
E2: Embossed tape and reel
Part Number
●Physical Dimension Tape and Reel Information
HTSOP-J8
<Tape and Reel information>
4.9 0.1
(MAX 5.25 include BURR)
Tape
Embossed carrier tape
(3.2)
+
−
Quantity
2500pcs
6
4
°
°
4°
8
7
2
6
3
5
E2
Direction
of feed
The direction is the 1pin of product is at the upper left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
1
4
1PIN MARK
+0.05
-0.03
0.545
0.17
S
1.27
+0.05
0.42
0.08
-
0.04
M
0.08
S
Direction of feed
1pin
Reel
Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
∗
●Marking Diagram
HTSOP-J8(TOP VIEW)
Part Number Marking
LOT Number
D 8 9 6 3 0
1PIN MARK
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
20/21
Daattaasshheeeett
BD89630EFJ
●Revision History
Date
Revision
001
Changes
28.Aug.2012
New Release
www.rohm.com
©2012 ROHM Co., Ltd. All rights reserved.
TSZ22111･15･001
TSZ02201-0J3J0AJ00270-1-2
2012.08.28 Rev.001
21/21
Daattaasshheeeett
Notice
Precaution on using ROHM Products
1. Our Products are designed and manufactured for application in ordinary electronic equipments (such as AV equipment,
OA equipment, telecommunication equipment, home electronic appliances, amusement equipment, etc.). If you
intend to use our Products in devices requiring extremely high reliability (such as medical equipment (Note 1), transport
equipment, traffic equipment, aircraft/spacecraft, nuclear power controllers, fuel controllers, car equipment including car
accessories, safety devices, etc.) and whose malfunction or failure may cause loss of human life, bodily injury or
serious damage to property (“Specific Applications”), please consult with the ROHM sales representative in advance.
Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way responsible or liable for any
damages, expenses or losses incurred by you or third parties arising from the use of any ROHM’s Products for Specific
Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are designed and manufactured for use under standard conditions and not under any special or
extraordinary environments or conditions, as exemplified below. Accordingly, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses arising from the use of any ROHM’s Products under any
special or extraordinary environments or conditions. If you intend to use our Products under any special or
extraordinary environments or conditions (as exemplified below), your independent verification and confirmation of
product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (even if you use no-clean type fluxes, cleaning residue of
flux is recommended); or Washing our Products by using water or water-soluble cleaning agents for cleaning
residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse. is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation (Pd) depending on Ambient temperature (Ta). When used in sealed area, confirm the actual
ambient temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used; if flow soldering method is preferred, please consult with the
ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice - GE
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
QR code printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since our Products might fall under controlled goods prescribed by the applicable foreign exchange and foreign trade act,
please consult with ROHM representative in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data. ROHM shall not be in any way responsible or liable
for infringement of any intellectual property rights or other damages arising from use of such information or data.:
2. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the information contained in this document.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice - GE
Rev.002
© 2014 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Pro ducts, you are requested to care fully read this document and fully understand its contents.
ROHM shall not be in an y way responsible or liable for failure, malfunction or accident arising from the use of a ny
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this docume nt is current as of the issuing date and subj ect to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the la test information with a ROHM sale s
representative.
3. The information contained in this doc ument is provi ded on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate an d/or error-free. ROHM shall not be in an y way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2014 ROHM Co., Ltd. All rights reserved.
相关型号：
BD8966FVM--TR
Low Noise High Efficiency Step-down Switching Regulator with Built-in Power MOSFET
ROHM
BD8966FVM-TR
Switching Regulator, Current-mode, 0.8A, 1200kHz Switching Freq-Max, PDSO8, ROHS COMPLIANT, MSOP-8
ROHM
BD8966FVM_10
Low Noise High Efficiency Step-down Switching Regulator with Built-in Power MOSFET
ROHM
©2020 ICPDF网 联系我们和版权申明