BDJ0BC0WFP [ROHM]
Fixed Positive LDO Regulator, 10V, PSSO5, ROHS COMPLIANT, TO-252, 5 PIN;
| 型号： | BDJ0BC0WFP |
| 厂家： | 
ROHM |
| 描述： | Fixed Positive LDO Regulator, 10V, PSSO5, ROHS COMPLIANT, TO-252, 5 PIN 输出元件 调节器 |
| 文件： | 总10页 (文件大小：436K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Secondary LDO Regulator Series for Local Power Supplies
1A Secondary LDO Regulators
for Local Power Supplies
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
No.09024EAT02
Description
The BA□□BC0 are low-saturation regulators with an output current of 1.0 A and an output voltage accuracy of 2%. A
broad output voltage range is offered, from 1.5V to 10V, and built-in overcurrent protection and thermal shutdown (TSD)
circuits prevent damage due to short-circuiting and overloading, respectively.
Features
1) Output current: 1 A (min.)
2) Output voltage accuracy: 2%
Broad output range available: 1.5 V -10 V (BA□□BC0 series)
3) Low saturation-voltage type with PNP output
4) Built-in overcurrent protection circuit
5) Built-in thermal shutdown circuit
6) Integrated shutdown switch (BA□□BC0WT, BA□□BC0WT-5, or BA□□BC0WFP Series, BA00BC0WCP-V5)
7) Operating temperature range: −40°C to +105°C
Applications
All electronic devices that use microcontrollers and logic circuits
Product Lineup
Part Number
1.5
1.8
2.5
3.0
3.3
5.0
6.0
7.0
8.0
9.0 10.0 Variable
Package
BA□□BC0WT
-
-
-
TO220FP-5
BA□□BC0WT-V5
BA□□BC0WFP
BA□□BC0T
-
-
-
-
-
-
-
-
-
TO220FP-5 (V5)
TO252-5
-
-
-
-
-
TO220FP-3
TO252-3
BA□□BC0FP
-
BA00BC0WCP-V5
TO220CP-V5
Part Number: BA□□BC0□ □
a
b c
Symbol
Description
Output voltage specification
□□
15
Output voltage (V)
1.5 V typ
□□
60
Output voltage (V)
6.0 V typ
18
1.8 V typ
70
7.0 V typ
a
25
2.5 V typ
80
8.0 V typ
30
3.0 V typ
90
9.0 V typ
33
3.3 V typ
J0
10.0 V typ
Variable
50
5.0 V typ
00
Existence of switch With W: A shutdown switch is provided.
b
c
Without W: No shutdown switch is provided.
Package
T: TO20FP-5, TO220FP-5(V5), TO220FP-3
FP: TO252-5, TO252-3
CP: TO220CP-V5
www.rohm.com
2009.04 - Rev.A
1/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Absolute Maximum Ratings (Ta = 25°C)
Parameter
Power supply voltage
TO252-3
Symbol
VCC
Limits
18*1
1200*2
1300*3
Unit
V
TO252-5
Power
dissipation TO220FP-5
TO220FP-5 (V5)
TO220FP-3
2000*4
2000*4
2000*4
mW
Pd
TO220CP-V5
Operating temperature range
Ambient storage temperature
2000*4
Topr
Tstg
−40 to +105
−55 to +150
150
°C
°C
°C
Maximum junction temperature
Tjmax
*1 Must not exceed Pd.
*2 Derated at 9.6mW/°C at Ta>25°C when mounted on a glass epoxy board (70 mm 70 mm 1.6 mm).
*3 Derated at 10.4mW/°C at Ta>25°C when mounted on a glass epoxy board (70 mm 70 mm 1.6 mm).
*4 Derated at 16mW/°C at Ta> 25°C
Recommended Operating Conditions
Parameter
Input power supply voltage
Input power supply voltage
Output current
Symbol
Min.
3.0
Max.
16.0
16.0
1
Unit
V
*5
VCC
*6
VcC
Vo+1.0
-
V
Io
A
Variable output voltage setting value
Vo
1.5
12
V
*5 When output voltage is 1.5 V, 1.8 V, or 2.5 V.
*6 When output voltage is 3.0 V or higher.
Electrical Characteristics
BA□□BC0FP/T/WFP/WT (−V5)
(Unless otherwise specified, Ta = 25°C; VCTL = 3 V; VCCDC )
*7
Parameter
Symbol
Min.
Typ.
Max.
Unit
V
Conditions
Vo (T)
0.98
Vo (T)
1.02
Output voltage
Vo
Vo (T)
Io = 200mA
Shutdown circuit current
Minimum I/O voltage difference*8
Output current capacity
Input stability*9
Isd
∆Vd
Io
-
-
0
0.3
-
10
0.5
-
A
V
VCTL = 0 V while in off mode
Io = 200 mA，Vcc = 0.95 Vo
1
-
A
Reg.I
Reg.L
15
35
35
75
mV
mV
Vcc = Vo+1.0V→16V, Io = 200mA
Io = 0 mA →1 A
Load stability
-
Temperature coefficient of
output voltage*10
Tcvo
-
0.02
-
%/°C Io = 5 mA､Tj = 0°C to 125℃
Vo (T): Set output voltage
*7
Vo = 1.5 V, 1.8 V, 2.5 V : Vcc = 3.3 V, Vo = 3.0 V, 3.3 V : Vcc = 5 V,
Vo = 5.0 V : Vcc : 8 V, Vo = 6.0 V : Vcc = 9 V, Vo = 8.0 V : Vcc = 11 V,
Vo = 9.0 V : Vcc = 12 V, Vo = 10.0 V : Vcc = 13 V
Vo ≥ 3.3 V
*8
*9
Change Vcc from 3.0 V to 6 V if 1.5 V ≤ Vo ≤ 2.5 V.
*10 Operation guaranteed
BA00BC0WFP/WT (−V5)/CP-V5
(Unless otherwise specified, Ta = 25°C, Vcc = 3.3 V, VCTL = 3 V, R1 = 30 k, R2 = 30 k*11
)
Parameter
Shutdown circuit current
Reference voltage
Symbol
Min.
Typ.
Max.
Unit
A
V
Conditions
Isd
-
0
10
VCTL = 0 V while in OFF mode
Io = 50 mA
Vc
1.225 1.250
1.275
0.5
-
Minimum I/O voltage difference
Output current capacity
Input stability
∆Vd
Io
-
1
-
0.3
-
V
Io = 500 mA, Vcc = 2.5V
A
Reg.I
Reg.L
15
35
30
mV
mV
Vcc = Vo + 1.0 V→16V, Io = 200 mA
Io = 0 mA →1A
Load stability
-
75
Temperature coefficient of output
voltage*12
Tcvo
-
0.02
-
%/°C Io = 5mA, Tj=0°C to 125°C
*11 VOUT = Vc (R1 + R2) / R1 (V)
*12 Operation guaranteed
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
2/8
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Electrical Characteristics Curves (Unless otherwise specified, Ta = 25°C, Vcc = 8 V, VCTL = 2 V, IO = 0 mA)
2.5
6
5
4
3
2
1
0
6
5
4
3
2
1
0
[BA50BC0WFP]
[BA50BC0WFP]
[BA50BC0WFP]
2
1.5
1
0.5
0
0
2
4
SUPPLY VOLTAGE ： Vcc [V]
6
8
10 12 14 16 18
0
2
4
6
8
10 12 14 16 18
0
2
4
6
8
10 12 14 16 18
SUPPLY VOLTAGE Vcc [V]
SUPPLY VOLTAGE ： Vcc [V]
：
Fig.1 Circuit Current
Fig.3 Input Stability(Io = 1 A)
Fig.2 Input Stability(Io=0mA)
70
60
6
5
4
3
2
1
0
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
[BA50BC0WFP]
[BA50BC0WFP]
[BA50BC0WFP]
50
40
30
20
10
0
0
200
400
600
800
1000
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
1.1 1.2 1.3 1.4 1.5 1.6 1.7
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
1
1.1 1.2 1.3
FREQUENCY ： f [Hz]
OUTPUT CURRENT ： IOUT [A]
OUTPUT CURRENT： IOUT [mA]
Fig.4 Load Stability
Fig.5 I/O Voltage Difference
Fig.6 Ripple Rejection
1
70
60
50
40
30
20
10
0
4
3.5
3
0.9
[BA50BC0WFP]
[BA50BC0WFP]
[BA50BC0WFP]
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
2.5
2
1.5
1
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100
-40 -30 -20 -10
0
10 20 30 40 50 60 70 80 90 100
0
100 200 300 400 500 600 700 800 900 1000
OUTPUT CURRENT ： IOUT [A]
TEMPERATURE： Ta [℃]
TEMPERATURE ： Ta [℃]
Fig.7 Output Voltage vs Temperature
Fig.8 Circuit Current Temperature
Fig.9 Circuit Current Classified by Load
6
5
4
3
2
1
0
0.6
8
[BA50BC0WFP]
[BA50BC0WFP]
7
0.5
0.4
0.3
0.2
0.1
0
6
5
4
3
2
1
0
[BA50BC0WFP]
0
2
4
6
8
10
0
2
4
6
8
10 12 14 16 18
100
120
140
160
180
200
CONTROL VOLTAGE ： VCTL [V]
CONTROL VOLTAGE ： VCTL [V]
TEMPERATURE ： Ta [℃]
Fig.10 CTL Voltage vs Output Voltage
Fig.11 CTL Voltage vs CTL Current
Fig.12 Thermal Shutdown Circuit
www.rohm.com
2009.04 - Rev.A
3/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Block Diagrams / Standard Example Application Circuits
[BA□□BC0T] / [BA□□BC0FP]
Pin No.
Pin name
Function
GND (TO252-3)
Fin
1
2
Vcc
N.C./GND
OUT
Supply voltage input
NC pin/GND *1
Voltage output
GMD*2
Vref
Driver
TOP VIEW
3
R2
R1
FIN
GND
*1 NC pin for TO252-3 and GND pin for TO220FP-3 and TO220FP-5 (V5).
*2 TO252-3 only.
TSD
OCP
1
2
3
OUT
Vcc
N.C.
(TO252-3)
PIN
External capacitor setting range
Approximately 0.33 F.
22 F to 1000 F
1
2 3
GND
(TO220FP-3)
22μF
Vcc (1 Pin）
OUT (3 Pin)
TO252-3
1 2 3
0.33μF
Fig.13
TO220FP-3
[BA□□BC0TWT] / [BA□□BC0WT-V5] / [BA□□BC0WFP]
Pin No.
Pin name
CTL
Function
TOP VIEW
GND(TO252-5)
1
2
Output voltage on/off control
Supply voltage input
NC pin/GND*1
Fin
Vcc
Vcc
N.C./GND
OUT
Vref
Driver
3
4
Power supply output
NC pin
R2
1
2
3
4
5
5
N.C.
FIN
GND
GND*2
TO252-5
R1
5
*1 NC pin for TO252-5 and GND pin for TO220FP-5 and TO220FP-5 (V5).
*2 TO252-5 only.
TSD
OCP
4
1
2
3
CTL
Vcc
N.C.
OUT
N.C.
(TO252-5)
GND
(TO220FP-5,
PIN
External capacitor setting range
Approximately 0.33 F.
22 F to 1000 F
-5(V5)
22μF
0.33μF
Vcc (2 Pin)
OUT (4 Pin)
1 2 3 4 5
1 2 3 4 5
TO220FP-5 TO220FP-5 (V5)
Fig.14
TOP VIEW
[BA00BC0WT] / [BA00BC0WFP]
Pin No.
Pin name
Function
Output voltage on/off control
Supply voltage input
NC pin/GND*1
GND(TO252-5)
Fin
1
2
CTL
Vcc
Vcc
Vref
Driver
3
N.C./GND
OUT
4
Power supply output
ADJ pin
1
2
4 5
3
1 2 3
TO252-5
TO220CP-V5
5
Ｃ
FIN
GND
GND*2
*1 NC pin for TO252-5 and GND pin for TO220FP-5 and TO220FP-5 (V5).
*2 TO252-5 only.
TSD
OCP
4
1
2
3
5
CTL
Vcc
N.C.
OUT
C
PIN
External capacitor setting range
Approximately 0.33 F.
22 F to 1000 F
(TO252-5)
GND
(TO220FP-5,
R2
22μF
Vcc (2 Pin)
OUT (4 Pin)
-5(V5)
R1
0.33μF
1 2 3 4 5
1 2 3 4 5
Fig.15
TO220FP-5 TO220FP-5 (V5)
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
4/8
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Input / Output Equivalent Circuit Diagrams
Vcc
* For the BA00BC0WT, connect R1 and
R2 externally between the C and GND
Vcc
pins and between the OUT and C pins.
OUT
27kΩ
2kΩ
CTL
R2
R1
31kΩ
Equation: VOUT = Vc (R1 + R2) / R1
(Vc = 1.25 V (Typ.))
The recommended R1 value is
approximately 30 k to 150 k.
Fig.16
Fig.17
Thermal Derating Curves
TO220FP-3/TO220FP-5/TO220FP-5V5）
TO252-3/TO252-5
25
20
15
10
5
2.0
1.6
1.2
0.8
0.4
0
(1) When using an infinite heat sink.
IC mounted on a ROHM standard board
j-c = 6.25 (°C/W)
Board size: 70 70 1.6 mm
Copper foil area: 7 7 mm
TO252-5 ja=96.2 (°C/W)
(1)20.0
(2) During IC without heat sink operation.
j-a = 62.5 (°C/W)
＝
TO252-3 ja 104.2 (°C/W)
1.30
TO252-5
TO252-3
(2)2.0
0
0
25
50
75
100
125 150
0
25
50
75
100
125 150
：
AMBIENT TEMPERATURE Ta [°C]
AMBIENT TEMPERATURE：Ta [°C]
Fig.18
Fig.19
The characteristics of the IC are greatly influenced by the operating temperature. If the temperature exceeds the maximum
junction temperature Tjmax, deterioration or damage may occur. Implement proper thermal designs to ensure that power
dissipation is within the permissible range in order to prevent instantaneous damage resulting from heat and maintain the
reliability of the IC for long-term operation.
The following method is used to calculate the power consumption Pc (W).
Pc = (Vcc – Vo) Io + Vcc Icca
Power dissipation Pd ≥ Pc
Vcc : Input voltage
Vo : Output current
IO : Load current
Icca : Circuit current
The load current Io is calculated:
Pd − Vcc Icca
Io ≤
Vcc − Vo
Calculation Example:
Vcc = 6.0 V and Vo = 5.0 V at Ta = 85°C
ja = 96.2°C/W → −10.4 mW/°C
25°C = 1300 mW → 85°C = 676 mW
0.676 − 6.0 Icca
6.0 − 5.0
Io ≤ 550 mA (Icca 20 mA)
Refer to the above and implement proper thermal designs so that the IC will not be used under excessive power dissipation
conditions under the entire operating temperature range.
The power consumption Pc of the IC in the event of shorting (i.e. the Vo and GND pins are shorted) can be obtained from the
following equation:
Pc = Vcc (Icca + Ishort) (Ishort: short current).
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
5/8
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Notes for use
Vcc pin
Insert a capacitor (0.33 F approx.) between VCC and GND.
The capacitance will vary depending on the application. Use a suitable capacitance and implement designs with
sufficient margins.
GND pin
Verify that there is no potential difference between the ground of the application board and the IC.
If there is a potential difference, the set voltage will not be output accurately, resulting in unstable IC operation.
Therefore, lower the impedance by designing the ground pattern as wide and as short as possible.
CTL pin
Ω
27k
Ω
2k
CTL
The CTL pin turns on at an operating power supply
voltage of 2.0 V or higher and turns off at 0.8 V or lower.
There is no particular order when turning the power
supply and CTL pins on or off.
Ω
31k
Fig.20 Input Equivalent Circuit
Vo pin
Iinsert a capacitor between the Vo and GND pins in order to prevent output oscillation.
10.0
Oscillation region
2.0
1.0
OUT
0.5
0.2
IC
Stable region
22 F
0.1
0.075
0.05
Oscillation region
Io [mA]
0
200 400 600 800 1000
Fig.21 Output Equivalent Circuit
Fig.22 ESR vs IO(22μF)
The capacitance may vary greatly with temperature changes, thus making it impossible to completely prevent oscillation.
Therefore, use a tantalum aluminum electrolytic capacitor with a low ESR (Equivalent Serial Resistance). The output will
oscillate if the ESR is too high or too low, so refer to the ESR characteristics in Fig. 20 and operate the IC within the stable
region. Use a capacitor within a capacitance between 22F and 1,000F.
Below figure,it is ESR-to-Io stability Area characteristics,measured by 22μＦ-ceramic-capacitor and resistor connected in series.
This characteristics is not equal value perfectly to 22µＦ-aluminum electrolytic capacitor in order to measurement method.
Note, however, that the stable range suggested in the figure depends on the IC and the resistance load involved, and can
vary with the board’s wiring impedance, input impedance, and/or load impedance. Therefore, be certain to ascertain the final
status of these items for actual use.
Keep capacitor capacitance within a range of 22µF～1000μF. It is also recommended that a 0.33μF bypass capacitor be
connected as close to the input pin-GND as location possible. However, in situations such as rapid fluctuation of the input
voltage or the load, please check the operation in real application to determine proper capacitance.
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
6/8
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
Notes for use
1. Absolute maximum ratings
An excess in the absolute maximum ratings, such as supply voltage, temperature range of operating conditions, etc., can break
down the devices, thus making impossible to identify breaking mode, such as a short circuit or an open circuit. If any over rated
values will expect to exceed the absolute maximum ratings, consider adding circuit protection devices, such as fuses.
2. GND voltage
The potential of GND pin must be minimum potential in all operating conditions.
3. Thermal design
Use a thermal design that allows for a sufficient margin in light of the power dissipation (Pd) in actual operating conditions.
4. Inter-pin shorts and mounting errors
Use caution when positioning the IC for mounting on printed circuit boards.
The IC may be damaged if there is any connection error or if pins are shorted together.
5. Actions in strong electromagnetic field
Use caution when using the IC in the presence of a strong electromagnetic field as doing so may cause the IC to malfunction.
6. Testing on application boards
When testing the IC on an application board, connecting a capacitor to a pin with low impedance subjects the IC to stress.
Always discharge capacitors after each process or step. Always turn the IC's power supply off before connecting it to or
removing it from a jig or fixture during the inspection process. Ground the IC during assembly steps as an antistatic
measure. Use similar precaution when transporting or storing the IC.
7. Regarding input pin of the IC
This monolithic IC contains P+ isolation and P substrate layers between adjacent elements in order to keep them isolated.
P-N junctions are formed at the intersection of these P layers with the N layers of other elements, creating a parasitic diode
or transistor. For example, the relation between each potential is as follows:
When GND > Pin A and GND > Pin B, the P-N junction operates as a parasitic diode.
When GND > Pin B, the P-N junction operates as a parasitic transistor.
Parasitic diodes can occur inevitable in the structure of the IC. The operation of parasitic diodes can result in mutual
interference among circuits, operational faults, or physical damage. Accordingly, methods by which parasitic diodes
operate, such as applying a voltage that is lower than the GND (P substrate) voltage to an input pin, should not be used.
8. Ground Wiring Pattern
When using both small signal and large current GND patterns, it is recommended to isolate the two ground patterns,
placing a single ground point at the ground potential of application so that the pattern wiring resistance and voltage
variations caused by large currents do not cause variations in the small signal ground voltage. Be careful not to change the
GND wiring pattern of any external components, either.
9. Thermal shutdown circuit
The IC incorporates a built-in thermal shutdown circuit (TSD circuit). The thermal shutdown circuit (TSD circuit) is designed
only to shut the IC off to prevent thermal runaway. It is not designed to protect the IC or guarantee its operation. Do not continue
to use the IC after operating this circuit or use the IC in an environment where the operation of this circuit is assumed.
10. Overcurrent Protection Circuit
An overcurrent protection circuit is incorporated in order to prevention destruction due to short-time overload currents.
Continued use of the protection circuits should be avoided. Please note that the current increases negatively impact the temperature.
11. Damage to the internal circuit or element may occur when the polarity of the Vcc pin is opposite to that of the other pins in
applications. (I.e. Vcc is shorted with the GND pin while an external capacitor is charged.) Use a maximum capacitance of
1000μF for the output pins. Inserting a diode to prevent back-current flow in series with Vcc or bypass diodes between Vcc
and each pin is recommended.
Resistor
Transistor (NPN)
(PINB)
B
Bypass Diode
C
（PIN B）
（
P
IN
A
）
C
E
E
B
Diode for preventing back current flow
GND
GND
N
VCC
P
Ｐ
P
P＋
P＋
P＋
P＋
Parasitic elements or
transistors
N
N
N
Output pin
N
N
N
Ｎ
(PINA)
P substrate
Parasitic elements
P substrate
Parasitic elements
GND
GND
Parasitic elements
GND
Fig.23 Bypass Diode
Fig.24 Example of Simple Bipolar IC Architecture
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
7/8
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
●Ordering part number
B D
1 8
B C 0
W
F P
-
E 2
Part number
Shutdown switch パッケージ
W : Include FP : TO252-3
TO252-5
Output voltage Current capacity
Packaging and forming specification
E2: Embossed tape and reel
None: Container tube
BC0 : 1A
00:Variable
Other:Fixed
T
: TO220FP-3
TO220FP-5
TO220FP-5(V5)
CP : TO220CP-V5
TO252-3
<Tape and Reel information>
Tape
Embossed carrier tape
2000pcs
6.5 0.2
C0.5
+0.2
Quantity
5.1
-
0.1
2.3 0.2
E2
0.5 0.1
Direction
of feed
The direction is the 1pin of product is at the lower left when you hold
reel on the left hand and you pull out the tape on the right hand
FIN
(
)
1
2
3
0.65
0.75
2.3 0.2
0.65
0.5 0.1
1.0 0.2
2.3 0.2
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
1pin
Reel
(Unit : mm)
∗
TO252-5
<Tape and Reel information>
Tape
Embossed carrier tape
2.3 0.2
0.5 0.1
6.5 0.2
Quantity
2000pcs
C0.5
+0.2
5.1
-0.1
E2
Direction
of feed
The direction is the 1pin of product is at the lower left when you hold
reel on the left hand and you pull out the tape on the right hand
(
)
FIN
3
1
2
4 5
0.5 0.1
1.0 0.2
0.5
1.27
Direction of feed
Order quantity needs to be multiple of the minimum quantity.
1pin
Reel
(Unit : mm)
∗
TO220CP-V5
<Tape and Reel information>
4.5 0.1
φ3.2 0.1
+0.3
+0.2
2.8
Tape
Embossed carrier tape
10.0
-
0.1
-
0.1
Quantity
500pcs
E2
Direction
of feed
The direction is the 1pin of product is at the lower left when you hold
(
)
reel on the left hand and you pull out the tape on the right hand
0.82 0.1
0.92
0.42 0.1
1.58
1.444
1.778
(2.85)
4.12
Direction of feed
1pin
Reel
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
2009.04 - Rev.A
8/8
© 2009 ROHM Co., Ltd. All rights reserved.
Technical Note
BA□□BC0 Series,BA□□BC0W Series,BA00BC0W Series
TO220FP-3
<Tape and Reel information>
+0.3
−0.1
+0.3
−0.1
+0.3
4.5
−0.1
10.0
Container
Quantity
Tube
+0.2
−0.1
7.0
2.8
φ
3.2 0.1
500pcs
Direction of feed Direction of products is fixed in a container tube
1.3
0.8
+0.1
0.55
−0.05
2.6 0.5
2.54 0.5
2.54 0.5
1
2 3
Order quantity needs to be multiple of the minimum quantity.
(Unit : mm)
∗
TO220FP-5
<Tape and Reel information>
+0.3
−0.1
+0.3
4.5
−0.1
10.0
Container
Quantity
Tube
+0.3
+0.2
−0.1
7.0
φ
2.8
3.2 0.1
−0.1
500pcs
Direction of feed Direction of products is fixed in a container tube
1.2
0.8
1.778
0.5 0.1
2.85
1
2 3 4 5
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
TO220FP-5(V5)
<Tape and Reel information>
+ 0.3
− 0.1
+0.3
10.0
4.5
−0.1
Container
Quantity
Tube
+0.2
2.8
−0.1
+ 0.3
φ
3.2 0.1
7.0
− 0.1
500pcs
Direction of feed Direction of products is fixed in a container tube
1.2
0.8
0.5 0.1
(2.85)
4.25
8.15
1.778
1
2 3 4 5
(Unit : mm)
Order quantity needs to be multiple of the minimum quantity.
∗
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
2009.04 - Rev.A
9/8
Notice
N o t e s
No copying or reproduction of this document, in part or in whole, is permitted without the
consent of ROHM Co.,Ltd.
The content specified herein is subject to change for improvement without notice.
The content specified herein is for the purpose of introducing ROHM's products (hereinafter
"Products"). If you wish to use any such Product, please be sure to refer to the specifications,
which can be obtained from ROHM upon request.
Examples of application circuits, circuit constants and any other information contained herein
illustrate the standard usage and operations of the Products. The peripheral conditions must
be taken into account when designing circuits for mass production.
Great care was taken in ensuring the accuracy of the information specified in this document.
However, should you incur any damage arising from any inaccuracy or misprint of such
information, ROHM shall bear no responsibility for such damage.
The technical information specified herein is intended only to show the typical functions of and
examples of application circuits for the Products. ROHM does not grant you, explicitly or
implicitly, any license to use or exercise intellectual property or other rights held by ROHM and
other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the
use of such technical information.
The Products specified in this document are intended to be used with general-use electronic
equipment or devices (such as audio visual equipment, office-automation equipment, commu-
nication devices, electronic appliances and amusement devices).
The Products specified in this document are not designed to be radiation tolerant.
While ROHM always makes efforts to enhance the quality and reliability of its Products, a
Product may fail or malfunction for a variety of reasons.
Please be sure to implement in your equipment using the Products safety measures to guard
against the possibility of physical injury, fire or any other damage caused in the event of the
failure of any Product, such as derating, redundancy, fire control and fail-safe designs. ROHM
shall bear no responsibility whatsoever for your use of any Product outside of the prescribed
scope or not in accordance with the instruction manual.
The Products are not designed or manufactured to be used with any equipment, device or
system which requires an extremely high level of reliability the failure or malfunction of which
may result in a direct threat to human life or create a risk of human injury (such as a medical
instrument, transportation equipment, aerospace machinery, nuclear-reactor controller,
fuel-controller or other safety device). ROHM shall bear no responsibility in any way for use of
any of the Products for the above special purposes. If a Product is intended to be used for any
such special purpose, please contact a ROHM sales representative before purchasing.
If you intend to export or ship overseas any Product or technology specified herein that may
be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to
obtain a license or permit under the Law.
Thank you for your accessing to ROHM product informations.
More detail product informations and catalogs are available, please contact us.
ROHM Customer Support System
http://www.rohm.com/contact/
www.rohm.com
© 2009 ROHM Co., Ltd. All rights reserved.
R0039
A
相关型号：
BDJ0FC0WEFJ
BDJ0FC0WEFJ是可提供最大1A电流的低饱和型稳压器。BDxxFC0WEFJ系列有可通过外部电阻设定输出电压的可变型和固定型产品。封装组件采用HTSOP-J8。本系列内置防止因输出短路等发生IC破坏的过电流保护、以及防止因过负荷状态等使IC发生热破坏的过热保护电路。
ROHM
BDJ0FC0WFP
BDJ0FC0WFP是可提供最大1A电流的低饱和型稳压器。输出电压固定型。封装是TO252-5。BDJ0FC0WFP内置防止因输出短路等发生IC破坏的过电流保护、以及防止因过负荷状态等使IC发生热破坏的过热保护电路。
ROHM
BDJ0GA3MEFJ-M
BDxxGA3MEFJ-M系列是可提供0.3A输出电流的稳压器。输出精度为±1%。有可使用外接电阻在1.5V～13.0V范围内任意设置输出电压的可变型以及1.5V/1.8V/2.5V/3.0V/3.3V/5V/6V/7V/8V/9V/10V/12V固定输出型两种。封装组件采用散热性优良的HTSOP-J8。本机型内置用于防止因输出短路等发生IC破坏的过电流保护电路、关断时使电路电流为0µA的ON/OFF开关、以及防止因过负荷状态等使IC发生热破坏的温度保护电路。另外，采用了陶瓷电容器，有助于整机的小型化和长寿化。
ROHM
BDJ0GA3VEFJ-M (新产品)
BDxxGA3VEFJ-M is a LDO regulator with output current 0.3A. The output accuracy is ±1% of output vo
ROHM
BDJ0GA3WEFJ
BDxxGA3WEFJ系列是可提供0.3A输出电流的稳压器。输出精度为±1%。有可使用外接电阻在1.5V～13.0V范围内任意设置输出电压的可变型以及1.5V/1.8V/2.5V/3.0V/3.3V/5V/6V/7V/8V/9V/10V/12V固定输出型两种。封装组件采用散热性优良的HTSOP-J8。可用于数字家电等广泛用途。本机型内置用于防止因输出短路等发生IC破坏的过电流保护电路、关断时使电路电流为0µA的ON/OFF开关、以及防止因过负荷状态等使IC发生热破坏的温度保护电路。另外，采用了陶瓷电容器，有助于整机的小型化和长寿化。
ROHM
BDJ0GA3WNUX
BDxxGA3WEFJ / BDxxGA3WNUX系列是可提供0.3A输出电流的稳压器。输出精度为±1%。有可使用外接电阻在1.5V～13.0V范围内任意设置输出电压的可变型以及1.5V/1.8V/2.5V/3.0V/3.3V/5V/6V/7V/8V/9V/10V/12V固定输出型两种。封装组件备有散热性优良的HTSOP-J8和超小型VSON008X2030。可用于数字家电等广泛用途。本机型内置用于防止因输出短路等发生IC破坏的过电流保护电路、关断时使电路电流为0µA的ON/OFF开关、以及防止因过负荷状态等使IC发生热破坏的温度保护电路。另外，采用了陶瓷电容器，有助于整机的小型化和长寿化。
ROHM
©2020 ICPDF网 联系我们和版权申明