BV1LB025EFJ-C [ROHM]
BV1LB025EFJ-C是车载用1ch低边开关。内置Dual TSD、OCP、有源钳位功能。;
| 型号： | BV1LB025EFJ-C |
| 厂家： | 
ROHM |
| 描述： | BV1LB025EFJ-C是车载用1ch低边开关。内置Dual TSD、OCP、有源钳位功能。 开关 |
| 文件： | 总26页 (文件大小：1953K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Datasheet
Automotive IPD 1ch Low Side Switch
BV1LB025EFJ-C
Features
Key Specifications
■ Built-in Dual TSD*1
On-state Resistance (Tj = 25 °C, Typ)
Over Current Limitation Level
(Tj = 25 °C, Typ)
Output Clamp Voltage (Min)
Active Clamp Energy (Tj(START) = 25 °C)
25 mΩ
■ AEC-Q100 Qualified*2
50 A
■ Built-in Over Current Protection Function(OCP)
■ Built-in Active Clamp Function
■ Direct Control Enabled from CMOS Logic IC, etc.
■ On Resistance RDS(ON) = 25 mΩ (Typ)
(when VIN 5 V, IOUT = 2.4 A, Tj 25 C)
■ Monolithic Power Management IC with the
Control Block (CMOS) and Power MOS FET
Mounted on a Single Chip
42 V
220 mJ
Package
HTSOP-J8
W (Typ) x D (Typ) x H (Max)
4.9 mm x 6.0 mm x 1.0 mm
*1 This IC has thermal shutdown (Junction temperature detect)
and ΔTj Protection (Power-MOS steep temperature rising
detect).
*2 Grade1
General Description
The BV1LB025EFJ-C is an automotive 1ch low side
switch IC, which has built-in Dual TSD, OCP and
active clamp function.
Application
■ Driving Resistive, Inductive and Capacitive Load
Block Diagram
OUT
Active Clamp Circuit
IN
Gate
Control
Dual TSD
OCP
GND
Product structure : Silicon integrated circuit This product has no designed protection against radioactive rays.
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 14 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
1/23
BV1LB025EFJ-C
Contents
Features.....................................................................................................................................................1
General Description......................................................................................................................................1
Application .................................................................................................................................................1
Key Specifications........................................................................................................................................1
Package .....................................................................................................................................................1
Block Diagram.............................................................................................................................................1
Contents ....................................................................................................................................................2
Pin Configuration.........................................................................................................................................3
Pin Description............................................................................................................................................3
Definition ...................................................................................................................................................3
Absolute Maximum Ratings...........................................................................................................................4
Recommended Operating Conditions..............................................................................................................5
Thermal Resistance .....................................................................................................................................5
Electrical Characteristics...............................................................................................................................9
Typical Performance Curves........................................................................................................................10
Measurement Circuit for Typical Performance Curves .....................................................................................15
I/O Pin Truth Table ....................................................................................................................................17
Timing Chart.............................................................................................................................................17
Function Description ..................................................................................................................................18
Operational Notes......................................................................................................................................19
Ordering Information.................................................................................................................................21
Marking Diagram.......................................................................................................................................21
Physical Dimension and Packing Information.................................................................................................22
Revision History ........................................................................................................................................23
www.rohm.com
TSZ02201-0GYG1G400120-1-2
© 2019 ROHM Co., Ltd. All rights reserved.
2/23
20.Nov.2020 Rev.001
TSZ22111 • 15 • 001
BV1LB025EFJ-C
Pin Configuration
HTSOP-J8
(TOP VIEW)
Pin Description
Pin No.
Pin Name
Function
1
2
3
4
5
6
7
8
IN
Input pin, with internal pull-down resistor.
N.C.
N.C.
N.C.
GND
GND
GND
GND
No connected to internal circuit. Open or connected to GND or connected IN.
No connected to internal circuit. Open or connected to GND or connected IN.
No connected to internal circuit. Open or connected to GND or connected IN.
GND pin
GND pin
GND pin
GND pin
Output pin. When output pin shorted to battery, output current is limited to protect
IC.
EXP-PAD
OUT
Definition
VBAT
RL, ZL
IIN
IOUT
VIN
IN
OUT
VOUT
VIN
GND
GND
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
3/23
BV1LB025EFJ-C
Absolute Maximum Ratings (Tj = 25°C)
Parameter
Symbol
Ratings
Unit
V
Output Voltage
Input Voltage
Output Current
VOUT
VIN
-0.3 to +42
-0.3 to +7
V
IOUT
35 (inside limited)*1
A
Active Clamp Energy (Single Pulse)
Tj(START) = 25 °C, IOUT(START) = 4 A
Active Clamp Energy (Single Pulse)
Tj(START) = 150 °C, IOUT(START) = 4 A *2
EAS(25 °C)
220
140
mJ
EAS(150 °C)
Storage Temperature Range
Tstg
-55 to +150
150
°C
°C
Maximum Junction Temperature
Tjmax
*1 Internally limited by over current protection function.
*2 Not 100 % tested.
Caution 1: Operating the IC over the absolute maximum ratings may damage the IC. The damage can either be a short circuit between pins
or an open circuit between pins and the internal circuitry. Therefore, it is important to consider circuit protection measures, such
as adding a fuse, in case the IC is operated over the absolute maximum ratings.
Caution 2: Should by any chance the maximum junction temperature rating be exceeded the rise in temperature of the chip may result in
deterioration of the properties of the chip. In case of exceeding this absolute maximum rating, design a PCB with thermal
resistance taken into consideration by increasing board size and copper area so as not to exceed the maximum junction
temperature rating.
Caution 3: When IC turns off with an inductive load, reverse energy has to be dissipated in the BV1LB025EFJ-C. This energy can be calculated
by the following equation:
1
2
푉
퐵퐴푇
퐸퐿
=
퐿퐼푂푈푇(푆푇퐴푅푇)2 × 1 −
ꢀ
푉
퐵퐴푇
− 푉푂푈푇(퐶퐿)
Where:
L is the inductance of the inductive load.
IOUT(START) is the output current at the time of turning off.
VOUT(CL) is the output clamp voltage.
The IC integrates the active clamp function to internally absorb the reverse energy EL which is generated when the inductive load
is turned off. When the active clamp operates, the thermal shutdown function does not work. Decide a load so that the reverse
energy EL is active clamp tolerance EAS (refer to Figure 1.) or under when inductive load is used.
1000
Tj(START) = 25 ℃
Tj(START) = 150 ℃
100
10
1
2
3
4
5
Output Current (Start): IOUT(START)[A]
Figure 1. Active Clamp Energy (Single Pulse) vs Output Current (Start)
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
4/23
BV1LB025EFJ-C
Recommended Operating Conditions
Parameter
Symbol
VIN
Min
3.5
-40
Typ
5.0
Max
5.5
Unit
V
Input Voltage
Operating Temperature
Tj
+25
+150
°C
Thermal Resistance*1
Parameter
Symbol
Typ
Unit
Condition
HTSOP-J8
*2
121.7
34.0
23.3
°C/W
°C/W
°C/W
1s
Between Junction and Surroundings Temperature
Thermal Resistance
*3
*4
θJA
2s
2s2p
*1 The thermal impedance is based on JESD51-2A (Still-Air) standard. It is used the chip of BV1LB025EFJ-C.
*2 JESD51-3 standard FR4 114.3 mm x 76.2 mm x 1.57 mm 1-layer (1s)
(Top copper foil: ROHM recommended Footprint + wiring to measure, 2 oz. copper.)
*3 JESD51-5 standard FR4 114.3 mm x 76.2 mm x 1.60 mm 2-layers (2s)
(Top copper foil: ROHM recommended Footprint + wiring to measure/
Copper foil area on the reverse side of PCB: 74.2 mm x 74.2 mm,
copper (top & reverse side) 2 oz.)
*4 JESD51-5, 7 standard FR4 114.3 mm x 76.2 mm x 1.60 mm 4-layers (2s2p)
(Top copper foil: ROHM recommended Footprint + wiring to measure/
2 inner layers and copper foil area on the reverse side of PCB: 74.2 mm x 74.2 mm,
copper (top & reverse side/inner layers) 2 oz./1 oz.)
■ PCB Layout 1 layer (1s)
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
5/23
BV1LB025EFJ-C
Thermal Resistance – continued
■
PCB Layout 2 layers (2s)
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
6/23
BV1LB025EFJ-C
Thermal Resistance – continued
■ PCB Layout 4 layers (2s2p)
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
7/23
BV1LB025EFJ-C
Thermal Resistance – continued
■ Transient Thermal Resistance (Single Pulse)
1000
100
10
1s footprint
2s
1
2s2p
0
0.0001 0.001
0.01
0.1
1
10
100
1000
Pulse Time[s]
■ Thermal Resistance (θJA vs Copper foil area (1s))
140
120
100
80
60
40
20
0
0
200
400
600
800
1000
1200
Copper Foil Area (1s) [mm2]
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
8/23
BV1LB025EFJ-C
Electrical Characteristics (Unless otherwise specified, 40 C ≤ Tj ≤ 150 C)
Limit
Parameter
Symbol
Unit
Conditions
Min
Typ
Max
Input (IN)
Input Threshold Voltage
VIN(TH)
IIN(H1)
IIN(H2)
IIN(L)
1.1
-
-
3.5
V
RL = 4.7 Ω, VBAT = 12 V
High Level Input Current 1
(in Normal Operation)
85
170
μA
VIN = 5 V
High Level Input Current 2
-
-
1000
+10
μA
μA
VIN = 5 V
VIN = 0 V
(in Abnormal Operation)*1
Low Level Input Current
Power MOS Output
-10
0
VIN = 5 V, IOUT = 2.4 A,
Tj = 25 °C
VIN = 5 V, IOUT = 2.4 A,
Tj = 150 °C
VIN = 0 V, VOUT = 18 V,
Tj = 25 °C
VIN = 0 V, VOUT = 18 V,
Tj = 150 °C
RDS(ON)
RDS(ON)
IOUT(L)
-
-
-
25.0
44.0
0.0
32.5
62.5
0.5
mΩ
mΩ
μA
On-state Resistance
Leak Current
IOUT(L)
VOUT(CL)
tON
-
42
-
2.5
48
50
50.0
54
μA
V
Output Clamp Voltage
Turn-ON Time
VIN = 0 V, IOUT = 1 mA
VIN = 0 V to 5 V, RL = 4.7 Ω,
VBAT = 12 V, Tj = 25 °C
100
μs
VIN = 5 V to 0 V, RL = 4.7 Ω,
VBAT = 12 V, Tj = 25 °C
VIN = 0 V to 5 V, RL = 4.7 Ω,
VBAT = 12 V, Tj = 25 °C
VIN = 5 V to 0 V, RL = 4.7 Ω,
VBAT = 12 V, Tj = 25 °C
Turn-OFF Time
Slew Rate On
tOFF
-
-
-
60
0.3
0.3
120
0.6
0.6
μs
SRON
SROFF
V/μs
V/μs
Slew Rate Off
Protection Function
Over Current Limitation Level
Thermal Shutdown Detected
Temperature
IOUT(LIM)
TTSDD
35
50
65
-
A
VIN = 5 V, Tj = 25 °C
150
180
°C
VIN = 5 V
*2
Thermal Shutdown Released
TTSDR
TTSDHYS
TDTJD
135
160
20
-
-
-
-
-
°C
°C
°C
°C
°C
VIN = 5 V
VIN = 5 V
VIN = 5 V
VIN = 5 V
VIN = 5 V
Temperature*2
Thermal Shutdown Hysteresis
Temperature*2
-
-
-
-
ΔTj Protection Detected
75
Temperature*2
ΔTj Protection Released
Temperature*2
TDTJR
45
ΔTj Protection Hysteresis
TDTJHYS
30
Temperature*2
*1 When thermal shutdown function or over current protection function is ON.
*2 Not 100 % tested.
www.rohm.com
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
© 2019 ROHM Co., Ltd. All rights reserved.
9/23
TSZ22111 • 15 • 001
BV1LB025EFJ-C
Typical Performance Curves
(Unless otherwise specified, Tj = 25 °C, VIN = 5 V)
3.5
175
150
125
100
75
VIN(TH) High
VIN(TH) Low
3.1
2.7
2.3
1.9
1.5
1.1
50
25
0
-40
0
40
80
120
150
3
4
5
6
7
Junction Temperature: Tj[℃]
Input Voltage: VIN [V]
Figure 2. Input Threshold Voltage vs Junction
Temperature
Figure 3. High Level Input Current 1 (in Normal
Operation) vs Input Voltage
175
150
125
100
75
50
25
0
-40
0
40
80
120
150
Junction Temperature: Tj[℃]
Figure 4. High Level Input Current 1 (in Normal
Operation) vs Junction Temperature
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
10/23
BV1LB025EFJ-C
Typical Performance Curves – continued
(Unless otherwise specified, Tj = 25 °C, VIN = 5 V)
60
50
40
30
20
10
0
60
50
40
30
20
10
0
150
3
4
5
6
7
-40
0
40
80
120
Input Voltage: VIN [V]
Junction Temperature: Tj[℃]
Figure 5. On-state Resistance vs Input Voltage
Figure 6. On-state Resistance vs Junction Temperature
50
40
30
20
10
0
54
52
50
48
46
44
42
-40
0
40
Junction Temperature: Tj[℃]
Figure 7. Leak Current vs Junction Temperature
80
120 150
-40
0
40
80
120
150
Junction Temperature: Tj[℃]
Figure 8. Output Clamp Voltage vs Junction Temperature
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
11/23
20.Nov.2020 Rev.001
BV1LB025EFJ-C
Typical Performance Curves – continued
(Unless otherwise specified, Tj = 25 °C, VIN = 5 V)
150
125
100
75
150
125
100
75
50
50
25
25
0
0
3
4
5
6
7
3
4
5
6
7
Input Voltage: VIN [V]
Figure 9. Turn-ON Time vs Input Voltage
Input Voltage: VIN [V]
Figure 10. Turn-OFF Time vs Input Voltage
120
120
100
80
60
40
20
0
100
80
60
40
20
0
150
-40
0
40
Junction Temperature: Tj[℃]
Figure 11. Turn-ON Time vs Junction Temperature
80
120
-40
0
40
80
120 150
Junction Temperature: Tj[℃]
Figure 12. Turn-OFF Time vs Junction Temperature
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
12/23
BV1LB025EFJ-C
Typical Performance Curves – continued
(Unless otherwise specified, Tj = 25 °C, VIN = 5 V)
0.8
0.6
0.4
0.2
0.0
0.8
0.6
0.4
0.2
0.0
3
4
5
6
7
3
4
5
6
7
Input Voltage: VIN [V]
Figure 13. Slew Rate On vs Input Voltage
Input Voltage: VIN [V]
Figure 14. Slew Rate Off vs Input Voltage
0.6
0.6
0.5
0.4
0.3
0.2
0.1
0.0
0.5
0.4
0.3
0.2
0.1
0.0
150
150
-40
0
40
Junction Temperature: Tj[℃]
Figure 15. Slew Rate On vs Junction Temperature
80
120
-40
0
40
80
120
Junction Temperature: Tj[℃]
Figure 16. Slew Rate Off vs Junction Temperature
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
13/23
BV1LB025EFJ-C
Typical Performance Curves – continued
(Unless otherwise specified, Tj = 25 °C, VIN = 5 V)
65
60
55
50
45
40
35
150
-40
0
40
80
120
Junction Temperature: Tj[℃]
Figure 17. Over Current Limitation Level
vs Junction Temperature
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
14/23
BV1LB025EFJ-C
Measurement Circuit for Typical Performance Curves
RL = 4.7 Ω
RL = 4.7 Ω
IN
OUT
IN
OUT
VIN
VBAT = 12 V
VIN
VBAT = 12 V
GND
GND
Measurement Circuit for Figure 2
Measurement Circuit for Figure 3 and Figure 4
IN
OUT
IN
OUT
VOUT = 18 V
IOUT = 2.4 A
VIN
RDS(ON)
= VOUT/IOUT
GND
GND
Measurement Circuit for Figure 5 and Figure 6
Measurement Circuit for Figure 7
VIN
=
0 V to 5 V
or
5 V to 0 V
RL = 4.7 Ω
Monitor
IN
OUT
IN
OUT
VBAT = 12 V
IOUT = 1 mA
Monitor
GND
GND
Measurement Circuit for Figure 8
Measurement Circuit for
Figure 9, Figure 10, Figure 11, Figure 12,
Figure 13, Figure 14, Figure 15 and Figure 16
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
15/23
BV1LB025EFJ-C
Measurement Circuit for Typical Performance Curves – continued
RL = 0.2 Ω
IN
OUT
VBAT
VIN
GND
Measurement Circuit for Figure 17
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
16/23
BV1LB025EFJ-C
I/O Pin Truth Table
Priority
IN Pin Voltage
Low
Operating Status
Standby
OUT Pin
OFF
1
2
Dual TSD Detection
OFF
High
Over Current
Limitation
3
4
Current Limitation
ON
High
High
Normal
Timing Chart
VIN [V]
5 V
VIN
VIN(TH)
0
t
VOUT [V]
tON [µs]
tOFF [µs]
≈ 12 V
80 %
VOUT
20 %
≈ 0 V
0
t
SRON [V/µs]
SROFF [V/µs]
Figure 18. Definition of Turn-ON Time, Turn-OFF Time, and Slew Rate
VIN [V]
VIN
VIN(TH)
0
t
VOUT(CL)
VOUT [V]
VOUT
VBAT
IOUT x RDS(ON)
t
t
0
IOUT [A]
VBAT
ZL + RDS(ON)
IOUT
0
Figure 19. Inductive Load Operation
17/23
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
BV1LB025EFJ-C
Function Description
■
Over Current Protection Function and Dual TSD Function
This IC has OCP function and Dual TSD function. Following shows the behavior when the OUT pin short
circuit.
Occurrence of short circuit
Dissolution of short circuit
①
②
③
②
③
④ ⑤④ ⑤④ ⑤④ ⑤④ ⑤
VIN
IOUT(LIM)
IOUT
Normal Current
TTSDD
TTSDR
TPOWER-MOS
TDTJD
TDTJR
Tj
TAMB
ΔTj
TSD
Figure 20. The Behavior when the OUT Pin Short Circuit
① IOUT is limited at Over Current Limitation Level (IOUT(LIM)) = 50 A (Typ) when over current is occurred.
② The temperature of Power MOS FET part and the control part in this IC is each TPOWER-MOS, TAMB
.
When the temperature difference becomes 75 °C (Typ) or more, the output turns OFF. This
temperature defines as ΔTj Protection Detected Temperature (TDTJD).
③ When the temperature difference of TPOWER-MOS and TAMB becomes 45 °C (Typ) or less, the output
turns automatically ON. This temperature defines as ΔTj Protection Released Temperature (TDTJR).
④ The output is turned off when the temperature of the IC reaches Thermal Shutdown Detected
Temperature (TTSDD) = 180 °C (Typ) or more.
⑤ The output returns to its normal state when the temperature of the IC becomes Thermal Shutdown
Released Temperature (TTSDR) = 160 °C (Typ) or less.
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
18/23
BV1LB025EFJ-C
Operational Notes
1. Ground Voltage
Ensure that no pins are at a voltage below that of the ground pin at any time, even during transient
condition.
2. Ground Wiring Pattern
When using both small-signal and large-current ground traces, the two ground traces should be routed
separately but connected to a single ground at the reference point of the application board to avoid
fluctuations in the small-signal ground caused by large currents. Also ensure that the ground traces of
external components do not cause variations on the ground voltage. The ground lines must be as short
and thick as possible to reduce line impedance.
3. Recommended Operating Conditions
The function and operation of the IC are guaranteed within the range specified by the recommended
operating conditions. The characteristic values are guaranteed only under the conditions of each item
specified by the electrical characteristics.
4. Testing on Application Boards
When testing the IC on an application board, connecting a capacitor directly to a low-impedance output
pin may subject the IC to stress. Always discharge capacitors completely after each process or step. The
IC’s power supply should always be turned off completely before connecting or removing it from the test
setup during the inspection process. To prevent damage from static discharge, ground the IC during
assembly and use similar precautions during transport and storage.
5. Inter-pin Short and Mounting Errors
Ensure that the direction and position are correct when mounting the IC on the PCB. Incorrect mounting
may result in damaging the IC. Avoid nearby pins being shorted to each other especially to ground, power
supply and output pin. Inter-pin shorts could be due to many reasons such as metal particles, water
droplets (in very humid environment) and unintentional solder bridge deposited in between pins during
assembly to name a few.
6. Ceramic Capacitor
When using a ceramic capacitor, determine a capacitance value considering the change of capacitance
with temperature and the decrease in nominal capacitance due to DC bias and others.
7. Thermal Shutdown Function (TSD)
This IC has a built-in thermal shutdown function that prevents heat damage to the IC. Normal operation
should always be within the IC’s maximum junction temperature rating. If however the rating is exceeded
for a continued period, the junction temperature (Tj) will rise which will activate the TSD function that will
turn OFF power output pins. When the Tj falls below the TSD threshold, the circuits are automatically
restored to normal operation.
Note that the TSD function operates in a situation that exceeds the absolute maximum ratings and
therefore, under no circumstances, should the TSD function be used in a set design or for any purpose
other than protecting the IC from heat damage.
8. Over Current Protection Function (OCP)
This IC incorporates an integrated overcurrent protection function that is activated when the load is
shorted. This protection function is effective in preventing damage due to sudden and unexpected
incidents. However, the IC should not be used in applications characterized by continuous operation or
transitioning of the protection function.
9. Active Clamp Operation
The IC integrates the active clamp function to internally absorb the reverse energy EL which is generated
when the inductive load is turned off. When the active clamp operates, the thermal shutdown function
does not work. Decide a load so that the reverse energy EL is active clamp tolerance EAS (refer to Figure
1.) or under when inductive load is used.
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
19/23
BV1LB025EFJ-C
Operational Notes – continued
10. Negative Current of Output
When the OUT pin (DRAIN) becomes lower than the GND pin (SOURCE), a current flow from the in pin
(the IN pin) to the OUT pin (DRAIN) through a parasitic transistor. As shown in Figure 21 when the input
pin is High, a current flow from a power supply of the connection (MCU, and so on) of the input pin to the
OUT pin (DRAIN). As shown in Figure 22 when the input pin is Low, a current flow from the GND of parts
(MCU, and so on) that connected to the input pin to the OUT pin (DRAIN).
Therefore, set the OUT pin (DRAIN) is -0.3 V or higher. When the OUT pin becomes lower than -0.3V, add
a restriction resistance 330 Ω or higher to the IN pin. However, set the value of restriction resistance in
consideration of the voltage descent caused by power supply pin and input pins currents.
MCU, and so on
GND
(SOURCE)
Restriction
resistance
Input pin
N+
N+
N+
N+
N+
P+
P-
P-
Parasitic Element
N-epi
N+sub
OUT
(DRAIN)
Figure 21. Negative Current Path (when the input pins are High)
MCU, and so on
GND
(SOURCE)
Input pin
Restriction
resistance
N+
N+
N+
N+
N+
P+
P-
P-
Parasitic Element
N-epi
N+sub
OUT
(DRAIN)
Figure 22. Negative Current Path (when the input pins are Low)
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
20/23
BV1LB025EFJ-C
Ordering Information
1
B V
L B 0 2 5 E F J
C E 2
Package
Product Grade
EFJ: HTSOP-J8
C: for Automotive
Packaging and forming specification
E2: Embossed tape and reel
Marking Diagram
HTSOP-J8 (TOP VIEW)
Part Number Marking
LOT Number
1 L B 2 5
Pin 1 Mark
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
21/23
BV1LB025EFJ-C
Physical Dimension and Packing Information
Package Name
HTSOP-J8
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
22/23
BV1LB025EFJ-C
Revision History
Date
Revision
Changes
20.Nov.2020
001
New Release
www.rohm.com
© 2019 ROHM Co., Ltd. All rights reserved.
TSZ22111 • 15 • 001
TSZ02201-0GYG1G400120-1-2
20.Nov.2020 Rev.001
23/23
Notice
Precaution on using ROHM Products
(Note 1)
1. If you intend to use our Products in devices requiring extremely high reliability (such as medical equipment
,
aircraft/spacecraft, nuclear power controllers, etc.) and whose malfunction or failure may cause loss of human life,
bodily injury or serious damage to property (“Specific Applications”), please consult with the ROHM sales
representative in advance. Unless otherwise agreed in writing by ROHM in advance, ROHM shall not be in any way
responsible or liable for any damages, expenses or losses incurred by you or third parties arising from the use of any
ROHM’s Products for Specific Applications.
(Note1) Medical Equipment Classification of the Specific Applications
JAPAN
USA
EU
CHINA
CLASSⅢ
CLASSⅣ
CLASSⅡb
CLASSⅢ
CLASSⅢ
CLASSⅢ
2. ROHM designs and manufactures its Products subject to strict quality control system. However, semiconductor
products can fail or malfunction at a certain rate. Please be sure to implement, at your own responsibilities, adequate
safety measures including but not limited to fail-safe design against the physical injury, damage to any property, which
a failure or malfunction of our Products may cause. The following are examples of safety measures:
[a] Installation of protection circuits or other protective devices to improve system safety
[b] Installation of redundant circuits to reduce the impact of single or multiple circuit failure
3. Our Products are not designed under any special or extraordinary environments or conditions, as exemplified below.
Accordingly, ROHM shall not be in any way responsible or liable for any damages, expenses or losses arising from the
use of any ROHM’s Products under any special or extraordinary environments or conditions. If you intend to use our
Products under any special or extraordinary environments or conditions (as exemplified below), your independent
verification and confirmation of product performance, reliability, etc, prior to use, must be necessary:
[a] Use of our Products in any types of liquid, including water, oils, chemicals, and organic solvents
[b] Use of our Products outdoors or in places where the Products are exposed to direct sunlight or dust
[c] Use of our Products in places where the Products are exposed to sea wind or corrosive gases, including Cl2,
H2S, NH3, SO2, and NO2
[d] Use of our Products in places where the Products are exposed to static electricity or electromagnetic waves
[e] Use of our Products in proximity to heat-producing components, plastic cords, or other flammable items
[f] Sealing or coating our Products with resin or other coating materials
[g] Use of our Products without cleaning residue of flux (Exclude cases where no-clean type fluxes is used.
However, recommend sufficiently about the residue.); or Washing our Products by using water or water-soluble
cleaning agents for cleaning residue after soldering
[h] Use of the Products in places subject to dew condensation
4. The Products are not subject to radiation-proof design.
5. Please verify and confirm characteristics of the final or mounted products in using the Products.
6. In particular, if a transient load (a large amount of load applied in a short period of time, such as pulse, is applied,
confirmation of performance characteristics after on-board mounting is strongly recommended. Avoid applying power
exceeding normal rated power; exceeding the power rating under steady-state loading condition may negatively affect
product performance and reliability.
7. De-rate Power Dissipation depending on ambient temperature. When used in sealed area, confirm that it is the use in
the range that does not exceed the maximum junction temperature.
8. Confirm that operation temperature is within the specified range described in the product specification.
9. ROHM shall not be in any way responsible or liable for failure induced under deviant condition from what is defined in
this document.
Precaution for Mounting / Circuit board design
1. When a highly active halogenous (chlorine, bromine, etc.) flux is used, the residue of flux may negatively affect product
performance and reliability.
2. In principle, the reflow soldering method must be used on a surface-mount products, the flow soldering method must
be used on a through hole mount products. If the flow soldering method is preferred on a surface-mount products,
please consult with the ROHM representative in advance.
For details, please refer to ROHM Mounting specification
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Precautions Regarding Application Examples and External Circuits
1. If change is made to the constant of an external circuit, please allow a sufficient margin considering variations of the
characteristics of the Products and external components, including transient characteristics, as well as static
characteristics.
2. You agree that application notes, reference designs, and associated data and information contained in this document
are presented only as guidance for Products use. Therefore, in case you use such information, you are solely
responsible for it and you must exercise your own independent verification and judgment in the use of such information
contained in this document. ROHM shall not be in any way responsible or liable for any damages, expenses or losses
incurred by you or third parties arising from the use of such information.
Precaution for Electrostatic
This Product is electrostatic sensitive product, which may be damaged due to electrostatic discharge. Please take proper
caution in your manufacturing process and storage so that voltage exceeding the Products maximum rating will not be
applied to Products. Please take special care under dry condition (e.g. Grounding of human body / equipment / solder iron,
isolation from charged objects, setting of Ionizer, friction prevention and temperature / humidity control).
Precaution for Storage / Transportation
1. Product performance and soldered connections may deteriorate if the Products are stored in the places where:
[a] the Products are exposed to sea winds or corrosive gases, including Cl2, H2S, NH3, SO2, and NO2
[b] the temperature or humidity exceeds those recommended by ROHM
[c] the Products are exposed to direct sunshine or condensation
[d] the Products are exposed to high Electrostatic
2. Even under ROHM recommended storage condition, solderability of products out of recommended storage time period
may be degraded. It is strongly recommended to confirm solderability before using Products of which storage time is
exceeding the recommended storage time period.
3. Store / transport cartons in the correct direction, which is indicated on a carton with a symbol. Otherwise bent leads
may occur due to excessive stress applied when dropping of a carton.
4. Use Products within the specified time after opening a humidity barrier bag. Baking is required before using Products of
which storage time is exceeding the recommended storage time period.
Precaution for Product Label
A two-dimensional barcode printed on ROHM Products label is for ROHM’s internal use only.
Precaution for Disposition
When disposing Products please dispose them properly using an authorized industry waste company.
Precaution for Foreign Exchange and Foreign Trade act
Since concerned goods might be fallen under listed items of export control prescribed by Foreign exchange and Foreign
trade act, please consult with ROHM in case of export.
Precaution Regarding Intellectual Property Rights
1. All information and data including but not limited to application example contained in this document is for reference
only. ROHM does not warrant that foregoing information or data will not infringe any intellectual property rights or any
other rights of any third party regarding such information or data.
2. ROHM shall not have any obligations where the claims, actions or demands arising from the combination of the
Products with other articles such as components, circuits, systems or external equipment (including software).
3. No license, expressly or implied, is granted hereby under any intellectual property rights or other rights of ROHM or any
third parties with respect to the Products or the information contained in this document. Provided, however, that ROHM
will not assert its intellectual property rights or other rights against you or your customers to the extent necessary to
manufacture or sell products containing the Products, subject to the terms and conditions herein.
Other Precaution
1. This document may not be reprinted or reproduced, in whole or in part, without prior written consent of ROHM.
2. The Products may not be disassembled, converted, modified, reproduced or otherwise changed without prior written
consent of ROHM.
3. In no event shall you use in any way whatsoever the Products and the related technical information contained in the
Products or this document for any military purposes, including but not limited to, the development of mass-destruction
weapons.
4. The proper names of companies or products described in this document are trademarks or registered trademarks of
ROHM, its affiliated companies or third parties.
Notice-PAA-E
Rev.004
© 2015 ROHM Co., Ltd. All rights reserved.
Daattaasshheeeett
General Precaution
1. Before you use our Products, you are requested to carefully read this document and fully understand its contents.
ROHM shall not be in any way responsible or liable for failure, malfunction or accident arising from the use of any
ROHM’s Products against warning, caution or note contained in this document.
2. All information contained in this document is current as of the issuing date and subject to change without any prior
notice. Before purchasing or using ROHM’s Products, please confirm the latest information with a ROHM sales
representative.
3. The information contained in this document is provided on an “as is” basis and ROHM does not warrant that all
information contained in this document is accurate and/or error-free. ROHM shall not be in any way responsible or
liable for any damages, expenses or losses incurred by you or third parties resulting from inaccuracy or errors of or
concerning such information.
Notice – WE
Rev.001
© 2015 ROHM Co., Ltd. All rights reserved.
相关型号：
BV1LC150EFJ-C (开发中)
BV1LC150EFJ-C是车载用的单通道低边开关。内置OCP、TSD及有源钳位功能。此外，利用其诊断功能还可以对OCP、TSD和开路负载（OLD）进行诊断。
ROHM
BV1LC300EFJ-C (开发中)
BV1LC300EFJ-C是车载用的单通道低边开关。内置OCP、TSD及有源钳位功能。此外，利用其诊断功能还可以对OCP、TSD和开路负载（OLD）进行诊断。
ROHM
©2020 ICPDF网 联系我们和版权申明