MNR02M0APJ303 [ROHM]

Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 30000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP;


型号：	MNR02M0APJ303
厂家：	ROHM
描述：	Array/Network Resistor, Isolated, Metal Glaze/thick Film, 0.063W, 30000ohm, 25V, 5% +/-Tol, 200ppm/Cel, Surface Mount, 0404, CHIP 电阻器
文件：	总4页 (文件大小：101K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

Compact Chip Resistor Networks

MNR02 (1005  2 size)

Features

1) Extremely small and light

Area ratio is 60% smaller than that of chip 1616 (MNR12), while weight ratio has been cut 75%.

2) High-density mounting

Can be mounted even more densely than two 1005 chips (MCR01). Also, the cost of mounting has been reduced.

3) Compatible with a wide range of mounting equipment.

Squared corners make it excellent for mounting using image recognition devices.

4) Convex electrodes

Easy to check the fillet after soldering is finished.

5) ROHM resistors have obtained ISO9001- / ISO/TS 16949- certification.

Ratings

Design and specifications are subject to change without notice. Carefully check the specification sheet before using or ordering

it.

Item

Conditions

Specifications

0.063W (1 / 16W)

Rated power

Power must be derated according to the power derating curve in

at 70°C

Figure 1 when ambient temperature exceeds 70°C.

100

−55

100 125

155

AMBIENT TEMPERATURE (°C)

Fig.1

Rated voltage

The voltage rating is calculated by the following equation.

If the value obtained exceeds the limiting element voltage,

the voltage rating is equal to the maximum operating voltage.

E: Rated voltage (V)

P: Rated power (W)

E = P×R

Limiting element voltage

25V

R: Nominal resistance (Ω)

Nominal resistance See Table 1.

Operating temperature

−55°C to +155°C

Jumper type

Resistance

Max. 50mΩ

Rated current

Operating temperature

Table 1

−55°C to +155°C

Resistance range

Resistance temperature coefficient

Resistance tolerance

J ( 5%)

(Ω)

(ppm / °C)

10 to 1M (E24)

200

Before using components in circuits where they will be exposed to transients such as pulse loads (short-duration, high-level loads), be certain to evaluate the

component in the mounted state. In addition, the reliability and performance of this component cannot be guaranteed if it is used with a steady state voltage that

is greater than its rated voltage.

www.rohm.com

2011.12 - Rev.F

1/3

Data Sheet

MNR02 (1005  2 size)

Characteristics

Guaranteed value

Items

Test conditions (JIS C 5201-1)

JIS C 5201-1 4.5

Resistor type

J : 5%

Jumper type

MAX.50mΩ

Resistance

Variation of resistance

with temperature

JIS C 5201-1 4.8

Measurement : +25 / +125°C

See Table.1

(2.0%+0.1Ω)

MAX.50mΩ

JIS C 5201-1 4.13

Rated voltage (current) ×2.5, 2s.

Limiting Element Voltage×2 : 50V

Overload

A new uniform coating of minimum of

95% of the surface being immersed

and no soldering damage.

JIS C 5201-1 4.17

Rosin·Ethanol (25%WT)

Soldering condition : 235 5°C

Duration of immersion : 2.0 0.5s.

Solderability

(1.0%+0.05Ω)

MAX.50mΩ

JIS C 5201-1 4.18

Soldering condition : 260 5°C

Duration of immersion : 10 1s.

Resistance to

soldering heat

No remarkable abnormality on the appearance.

MAX.50mΩ

(1.0%+0.05Ω)

(3.0%+0.1Ω)

JIS C 5201-1 4.19

Test temp. : −55°C to +125°C 5cyc

Rapid change of

temperature

JIS C 5201-1 4.24

40°C, 93%RH

Test time : 1,000h to 1,048h

MAX.100mΩ

Damp heat, steady state

(3.0%+0.1Ω)

JIS C 5201-1 4.25.1

MAX.100mΩ

Rated voltage (current), 70°C

1.5h : ON − 0.5h : OFF

Test time : 1,000h to 1,048h

Endurance at 70°C

(3.0%+0.1Ω)

(1.0%+0.05Ω)

JIS C 5201-1 4.25.3

125°C

MAX.100mΩ

MAX.50mΩ

Endurance

Test time : 1,000h to 1,048h

JIS C 5201-1 4.29

23 5°C, Immersion cleaning, 5 0.5min.

Solvent : 2-propanol

Resistance to solvent

MAX.50mΩ

JIS C 5201-1 4.33

Bend strength of

the end face plating

Without mechanical damage such as breaks.

Dimensions (Unit: mm)

1.0 0.1

No.

Material

Resistive element (Oxide metal thick film)

Silver thick film electrode

Nickel electrode

Cross section A-A'

Cross section B-B'

Sn electrode

Alumina substrate

Overcoating (Resin)

0.35 0.1

+0.1

+0.05

−0.1

0.33

0.34

−0.05

0.68

Equivalent circuit

R1 = R2

www.rohm.com

2011.12 - Rev.F

2/3

Data Sheet

MNR02 (1005  2 size)

Packaging

Reel

Taping

Heat crimp cover / Tape

Chip network

resistors

Thick paper (Underside paper tape)

mount

Square punchout hole

Label

EIAJ ET-7200B (RRM) compliant

(Unit: mm)

8.0 0.3

3.5 0.05

1.75 0.1

1.17 0.1

+0.1

4.0 0.1

2.0 0.1

2.0 0.05

Max. 0.5

φ1.5

Label

EIAJ ET-7200B (RRV) compliant

(Unit: mm)

−1.5

+1.0

φ180

φ60

φ13 0.2

Part No. Explanation

Part No.

Resistance tolerance

Nominal resistance

Resistance code, 3

000 denotes jumper type.

J is also used

for jumper.

Resistance

tolerance

Resistance

code

Packaging Specifications Code

3digits

Resistance tolerance

J( 5%)

Part No. Code

MNR02 M0AP

Packaging specifications

Reel

Basic ordering unit (pcs)

Paper tape (2mmPitch)

φ180mm

10,000

Reel (φ180mm) : Compatible with JEITA standard "EIAJ ET-7200B"

: Standard product

www.rohm.com

2011.12 - Rev.F

3/3

Notice

N o t e s

No copying or reproduction of this document, in part or in whole, is permitted without the

consent of ROHM Co.,Ltd.

The content speciﬁed herein is subject to change for improvement without notice.

The content speciﬁed herein is for the purpose of introducing ROHM's products (hereinafter

"Products"). If you wish to use any such Product, please be sure to refer to the speciﬁcations,

which can be obtained from ROHM upon request.

Examples of application circuits, circuit constants and any other information contained herein

illustrate the standard usage and operations of the Products. The peripheral conditions must

be taken into account when designing circuits for mass production.

Great care was taken in ensuring the accuracy of the information speciﬁed in this document.

However, should you incur any damage arising from any inaccuracy or misprint of such

information, ROHM shall bear no responsibility for such damage.

The technical information speciﬁed herein is intended only to show the typical functions of and

examples of application circuits for the Products. ROHM does not grant you, explicitly or

implicitly, any license to use or exercise intellectual property or other rights held by ROHM and

other parties. ROHM shall bear no responsibility whatsoever for any dispute arising from the

use of such technical information.

The Products speciﬁed in this document are intended to be used with general-use electronic

equipment or devices (such as audio visual equipment, ofﬁce-automation equipment, commu-

nication devices, electronic appliances and amusement devices).

The Products speciﬁed in this document are not designed to be radiation tolerant.

While ROHM always makes efforts to enhance the quality and reliability of its Products, a

Product may fail or malfunction for a variety of reasons.

Please be sure to implement in your equipment using the Products safety measures to guard

against the possibility of physical injury, ﬁre or any other damage caused in the event of the

failure of any Product, such as derating, redundancy, ﬁre control and fail-safe designs. ROHM

shall bear no responsibility whatsoever for your use of any Product outside of the prescribed

scope or not in accordance with the instruction manual.

The Products are not designed or manufactured to be used with any equipment, device or

system which requires an extremely high level of reliability the failure or malfunction of which

may result in a direct threat to human life or create a risk of human injury (such as a medical

instrument, transportation equipment, aerospace machinery, nuclear-reactor controller, fuel-

controller or other safety device). ROHM shall bear no responsibility in any way for use of any

of the Products for the above special purposes. If a Product is intended to be used for any

such special purpose, please contact a ROHM sales representative before purchasing.

If you intend to export or ship overseas any Product or technology speciﬁed herein that may

be controlled under the Foreign Exchange and the Foreign Trade Law, you will be required to

obtain a license or permit under the Law.

Thank you for your accessing to ROHM product informations.

More detail product informations and catalogs are available, please contact us.

ROHM Customer Support System

http://www.rohm.com/contact/

www.rohm.com

R1120

MNR02M0APJ303 [ROHM]

相关型号：

MNR02M0APJ304

MNR02M0APJ331

MNR02M0APJ332

MNR02M0APJ333

MNR02M0APJ334

MNR02M0APJ360

MNR02M0APJ361

MNR02M0APJ363

MNR02M0APJ364

MNR02M0APJ472

MNR02M0APJ560

MNR02M0APJ562