SGM4558 [SGMICRO]
Dual SIM/Smart Card Power Supply and Interface;型号: | SGM4558 |
厂家: | Shengbang Microelectronics Co, Ltd |
描述: | Dual SIM/Smart Card Power Supply and Interface |
文件: | 总7页 (文件大小:360K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
SGM4558
Dual SIM/Smart Card
Power Supply and Interface
GENERAL DESCRIPTION
FEATURES
The SGM4558 is used for power conversion and level
translation of the signal in the application of SIMs for
mobile phones. Also, it can be used for the applications
of 1.8V or 3.3V SIMs, which is powered by its internal
LDOs from 2.7V to 5.5V input signal. The value of the
output voltage can be controlled with the voltage
selection pins of the SGM4558 with the maximum load
current of 250mA. The function of the channel selection
pins is that it can be used to determine the open
condition of the specific channel. The two SIM cards
can be powered by the SGM4558 at once with the
control of the enable pins for each channel, and the fast
translation can be made from channel A to channel B.
● Controlling of Two SIM or Smart Cards with the
Internal Power Management
● Both Connected Cards are Powered by the
1.8V/3.3V Power Supply
● Two LDOs Support up to 250mA Loading
● Powering Two SIM or Smart Cards at the Same
Time
● Quick Switching from One Channel to Another
● Automatic Level Translation
● Fast Rising Time for the Signals
● Protecting Mechanism for Any Fault Conditions
● Mechanism which can Activate/Deactivate the
Sequence
● Extreme Low Supply Voltage and Shutdown
Current
The level translator integrated on the SGM4558 can
boost the input signal which is powered by 1.4V to 1.8V
or 3V interface. If the supply voltage is below 3.3V, the
lifespan of the battery can be enhanced as the 90μA
operating current and 2μA shutdown current.
● -40℃ to +85℃ Operating Temperature Range
● Available in a Green TQFN-3×3-20L Package
APPLICATIONS
The SGM4558 is available in a Green TQFN-3×3-20L
package. It operates over an ambient temperature
range of -40℃ to +85℃.
Multiple SIM Card Interfaces
TD-SCDMA, GSM and Other 3G+ Mobile Phones
Wireless Point-of-Sale Terminals
TYPICAL APPLICATION
1.4V to 5.5V
2.7V to 5.5V
1µF
1µF
DVCC
DVCC
VBAT
I/OA
I/O
CLKIN
RSTA
CLKA
RSTIN
RST
CLK
1.8V/3V
SIM Card A
Controller
SGM4558
DATA
CLKRUNA
CLKRUNB
VCCA
VCC
GND
1µF
1µF
ENABLEA
ENABLEB
CSEL
VCC
VCCB
CLK
RST
I/O
1.8V/3V
SIM Card B
CLKB
RSTB
VSELA
VSELB
I/OB
GND
GND
Figure 1. Typical Application Circuit
SG Micro Corp
JUNE2013–REV. A
www.sg-micro.com
Dual SIM/Smart Card
SGM4558
Power Supply and Interface
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
ORDERING
NUMBER
PACKAGE
MARKING
PACKING
OPTION
MODEL
SGM
SGM4560
TQFN-3×3-20L
SGM4558YTQG20G/TR
4558QG
XXXXX
Tape and Reel, 3000
-40℃ to +85℃
MARKING INFORMATION
NOTE: XXXXX = Date Code and Vendor Code.
X X X X X
Vendor Code
Date Code - Week
Date Code - Year
Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.
OVERSTRESS CAUTION
ABSOLUTE MAXIMUM RATINGS
Voltage Range (with Respect to GND)
Stresses beyond those listed in Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods
may affect reliability. Functional operation of the device at any
conditions beyond those indicated in the Recommended
Operating Conditions section is not implied.
VBAT
,
DVCC
,
RSTIN, CLKIN, CLKRUNA, CLKRUNB,
ENABLEA, ENABLEB, CSEL, VSELA, VSELB
........................................................................... -0.3V to 6V
V
CCA, VCCB ............................................ -0.3V to VBAT + 0.3V
DATA ..................................................-0.3V to DVCC + 0.3V
I/OA, CLKA, RSTA...............................-0.3V to VCCA + 0.3V
I/OB, CLKB, RSTB...............................-0.3V to VCCB + 0.3V
Package Thermal Resistance
ESD SENSITIVITY CAUTION
This integrated circuit can be damaged if ESD protections are
not considered carefully. SGMICRO recommends that all
integrated circuits be handled with appropriate precautions.
Failureto observe proper handlingand installation procedures
can cause damage. ESD damage can range from subtle
performance degradation tocomplete device failure. Precision
integrated circuits may be more susceptible to damage
because even small parametric changes could cause the
device not to meet the published specifications.
TQFN-3×3-20L, θJA.................................................. 95℃/W
Junction Temperature.................................................+150℃
Storage Temperature Range.......................-65℃ to +150℃
Lead Temperature (Soldering, 10s)............................+260℃
ESD Susceptibility
HBM.............................................................................4000V
MM.................................................................................300V
RECOMMENDED OPERATING CONDITIONS
Operating Temperature Range......................-40℃ to +85℃
DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuit design, or specifications without prior notice.
SG Micro Corp
www.sg-micro.com
JUNE 2013
2
Dual SIM/Smart Card
SGM4558
Power Supply and Interface
PIN CONFIGURATION
(TOP VIEW)
20
19
18
GND
8
17
16
VCCB
1
2
3
4
5
CLKRUNB
CLKRUNA
CSEL
15
14
13
12
11
DVCC
VBAT
VCCA
VSELA
CLKA
ENABLEA
6
7
9
10
TQFN-3×3-20L
PIN DESCRIPTION
PIN
NAME
FUNCTION
Card Socket. Both VCCA and VCCB pins should be connected to the power supply pin of the SIM
cards respectively. Also, the voltage of VCCA/VCCB which is controlled by the enable pin of the
SGM4558 can be set to 1.8V or 3V.
1, 4
VCCB, VCCA
2
3
DVCC
VBAT
Control Logic Reference Supply Voltage.
Analog Supply Voltage.
Card Socket. Both CLKA and CLKB pins of the SGM4558 should be connected to the card
socket of the SIM cards respectively. Also, these two pins are derived by the CLKIN, which can
be level shifted. If VCCA and VCCB obtain its corrected values, both CLKA and CLKB will start to
operate with the connected SIM cards. The pin will be low or left active through CLKRUNA,
CLKRUNB pins if the card socket is not detected by the SGM4558.
CLKA,
CLKB
5, 20
Card Socket. These two pins are used to be connected to the RST pins of the card socket
respectively. Also, these two pins are derived by the RSTIN pin. The RST pin is selected
6, 19
7, 18
RSTA, RSTB successfully if the card is selected. If VCCA and VCCB obtain its corrected values, both RSTA and
RSTB will start to operate with the connected SIM cards. However, the RST pin is latched at the
current state if deselecting the card socket.
Card Socket. These two pins should be connected to the associated pins of the card socket.
When the SIM card is selected, the I/O pins of the SGM4558 can transmit or receive the
information from the DATA pin. If VCCA and VCCB obtain its corrected values, both I/OA and I/OB
I/OA, I/OB
will start to operate with the connected SIM cards.
Microcontroller Side Bidirectional Data Input/Output Pin. The DATA pin can select a card at a
time. There is a weak current source integrated inside the pin. Therefore, the output of the
controller can be open-drain and it remains high state during shutdown mode, while DVCC must
be operated during the progress.
8
9
DATA
RSTIN
Reset Input Pin. The signal is transmitted directly to the selected SIM card.
SG Micro Corp
www.sg-micro.com
JUNE 2013
3
Dual SIM/Smart Card
SGM4558
Power Supply and Interface
PIN DESCRIPTION (continued)
PIN
NAME
FUNCTION
Clock Input Pin. The clock signal is sent to the CLK pin of the selected SIM card. The
CLKA/CLKB pin will receive the clock signal if the voltage level of CLKRUNA/CLKRUNB is in
high state.
10
CLKIN
ENABLEA,
ENABLEB
11, 17
12, 16
Enable Input Pins. These two pins can be used to enable or disable the selected card socket.
Select Input Pins. These two pins can be used to select the supply voltage level of the connected
SIM cards. Setting it to a high state will provide a 3V power supply to respective SIM card. Setting
it to a low state will provide 1.8V to respective SIM card.
VSELA,
VSELB
13
CSEL
SIM/Smart Card Select Input Pin. It depends on which is the activated SIM/Smart card.
CLKRUNA,
CLKRUNB
Clock Run Input Pins. These two pins are used to determine whether the clock signal always
transmits to the enabled SIM card or be controlled by the selected CSEL.
14, 15
Exposed
Pad
GND
Ground. Tie externally to a PCB ground plane.
SG Micro Corp
www.sg-micro.com
JUNE 2013
4
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
TQFN-3×3-20L
D
e
L
D1
E
E1
N20
k
N1
b
BOTTOM VIEW
TOP VIEW
1.5
0.7
A
3.5 2.1 1.5
A1
A2
SIDE VIEW
0.4
0.2
RECOMMENDED LAND PATTERN (Unit: mm)
Dimensions
In Millimeters
Dimensions
In Inches
Symbol
MIN
MAX
0.800
0.050
MIN
0.028
0.000
MAX
0.031
0.002
A
A1
A2
D
0.700
0.000
0.203 REF
0.008 REF
2.924
1.400
2.924
1.400
3.076
1.600
3.076
1.600
0.115
0.055
0.115
0.055
0.121
0.063
0.121
0.063
D1
E
E1
k
0.200 MIN
0.400 TYP
0.008 MIN
0.016 TYP
b
0.150
0.324
0.250
0.476
0.006
0.013
0.010
0.019
e
L
NOTE: This drawing is subject to change without notice.
SG Micro Corp
TX00082.000
www.sg-micro.com
PACKAGE INFORMATION
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
P2
P0
W
Q2
Q4
Q2
Q4
Q2
Q4
Q1
Q3
Q1
Q3
Q1
Q3
B0
Reel Diameter
P1
A0
K0
Reel Width (W1)
DIRECTION OF FEED
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF TAPE AND REEL
Reel Width
Reel
Diameter
A0
B0
K0
P0
P1
P2
W
Pin1
Package Type
W1
(mm)
(mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
TQFN-3×3-20L
13″
12.4
3.30
3.30
1.10
4.0
8.0
2.0
12.0
Q1
SG Micro Corp
TX10000.000
www.sg-micro.com
PACKAGE INFORMATION
CARTON BOX DIMENSIONS
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF CARTON BOX
Length
(mm)
Width
(mm)
Height
(mm)
Reel Type
Pizza/Carton
13″
386
280
370
5
SG Micro Corp
www.sg-micro.com
TX20000.000
相关型号:
SGM4574
4-Bit Bidirectional Voltage-Level Translator for Open-Drain and Push-Pull Applications
SGMICRO
SGM4576
6-Bit Bidirectional Voltage-Level Translator for Open-Drain and Push-Pull Applications
SGMICRO
SGM4578
8-Bit Bidirectional Voltage-Level Translator for Open-Drain and Push-Pull Applications
SGMICRO
©2020 ICPDF网 联系我们和版权申明