SGM61020/P [SGMICRO]
2A High Efficiency Synchronous Buck Converter;
| 型号： | SGM61020/P |
| 厂家： | 
Shengbang Microelectronics Co, Ltd |
| 描述： | 2A High Efficiency Synchronous Buck Converter |
| 文件： | 总17页 (文件大小：894K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SGM61020
2A High Efficiency
Synchronous Buck Converter
GENERAL DESCRIPTION
FEATURES
The SGM61020 is a high efficiency synchronous Buck
DC/DC converter with 2A output current capability and
adjustable output voltage. The input supply voltage is in
the range of 2.5V to 5.5V. Using adaptive off-time peak
current control, the efficiency of this device is higher
than 80% for loads over 1mA and reaches 95% in the
moderate load ranges (5V to 3.3V).
● 2.5V to 5.5V Input Voltage Range
● Adjustable Output Voltage from 0.6V to VIN
● Up to 95% Efficiency
● Low RDSON MOSFET Switches (100mΩ/55mΩ)
● Power-Save Mode for Light Load Efficiency
● 42μA (TYP) Operating Quiescent Current
● 100% Duty Cycle Capability for Low Dropout
● 1.5MHz PWM Switching Frequency
● Power Good Output (SGM61020P Only)
● Over-Current Protection
This device operates with a quasi-fixed 1.5MHz pulse
width modulation (PWM) mode for moderate or heavy
loads. But at light loads, pulse skip modulation is used
for power-save mode (PSM). The PSM operating
quiescent current is very low, typically 42μA, which is
well suitable for battery-powered applications to
increase standby time. Despite such low quiescent
current, the transient response to large load variations
is excellent. The device shutdown current is typically
0.03μA.
● Thermal Shutdown Protection
● Input Under-Voltage Lockout (UVLO) Protection
● Small Packaging:
SGM61020: Available in Green SOT-23-5 and
SOT-563-6 Packages
SGM61020P: Available in a Green SOT-563-6
Package
The SGM61020 provides an adjustable output voltage
by an external resistor divider. The device is capable for
low dropout operation with 100% duty cycle. Some
other features include internal soft-start for limiting
startup inrush current, over-current and thermal
shutdown protections, enable input and power good
output (for SGM61020P version only).
APPLICATIONS
Battery-Powered Applications
Point-of-Load
Processor Power Supplies
Hard Disk Drives (HDD)/Solid State Drives (SSD)
The SGM61020 is available in Green SOT-23-5 and
SOT-563-6 packages.
TYPICAL APPLICATION
L1
2.2μH
VIN
VOUT
1.8V
VIN
SW
2.5V to 5.5V
CIN
4.7μF
COUT
10μF
R1
200kΩ
SGM61020P
R3
510kΩ
FB
EN
R2
PG
GND
100kΩ
Power Good
Figure 1. Typical Application Circuit
SG Micro Corp
www.sg-micro.com
AUGUST2022–REV. A.1
2A High Efficiency
SGM61020
Synchronous Buck Converter
PACKAGE/ORDERING INFORMATION
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
DESCRIPTION
ORDERING
NUMBER
PACKAGE
MARKING
PACKING
OPTION
MODEL
SOT-23-5
SOT-563-6
SOT-563-6
SGM61020XN5G/TR
SGM61020XKB6G/TR
SGM61020PXKB6G/TR
RAAXX
ZMXX
ZNXX
Tape and Reel, 3000
Tape and Reel, 5000
Tape and Reel, 5000
-40℃ to +125℃
-40℃ to +125℃
-40℃ to +125℃
SGM61020
SGM61020P
Green (RoHS & HSF): SG Micro Corp defines "Green" to mean Pb-Free (RoHS compatible) and free of halogen substances. If
you have additional comments or questions, please contact your SGMICRO representative directly.
MARKING INFORMATION
SOT-23-5
SOT-563-6
(1) XX = Date Code.
YYY X X
(2) XX = Date Code.
YY X X
Date Code - Week
Date Code - Week
Date Code - Year
Serial Number
Date Code - Year
Serial Number
OVERSTRESS CAUTION
ABSOLUTE MAXIMUM RATINGS
Stresses beyond those listed in Absolute Maximum Ratings
may cause permanent damage to the device. Exposure to
absolute maximum rating conditions for extended periods
may affect reliability. Functional operation of the device at any
conditions beyond those indicated in the Recommended
Operating Conditions section is not implied.
Voltage Range Referred to GND
VIN, EN, PG......................................................... -0.3V to 6V
FB..................................................................... -0.3V to 5.5V
SW (DC) ...................................................-0.3V to VIN + 0.3V
SW (AC, Less than 10ns) while Switching.............. -2V to 9V
Package Thermal Resistance
SOT-23-5, θJA .......................................................... 193℃/W
SOT-563-6, θJA ........................................................ 170℃/W
Junction Temperature .................................................+150℃
Storage Temperature Range........................-65℃ to +150℃
Lead Temperature (Soldering, 10s) ............................+260℃
ESD Susceptibility
ESD SENSITIVITY CAUTION
This integrated circuit can be damaged if ESD protections are
not considered carefully. SGMICRO recommends that all
integrated circuits be handled with appropriate precautions.
Failureto observe proper handlingand installation procedures
can cause damage. ESD damage can range from subtle
performance degradation tocomplete device failure. Precision
integrated circuits may be more susceptible to damage
because even small parametric changes could cause the
device not to meet the published specifications.
HBM.............................................................................4000V
CDM ............................................................................1000V
RECOMMENDED OPERATING CONDITIONS
Input Voltage Range, VIN.....................................2.5V to 5.5V
Output Voltage Range, VOUT ................................. 0.6V to VIN
Output Current Range, IOUT ........................................0 to 2A
PG Pin Sink Current, ISINK_PG ...............................1mA (MAX)
Operating Junction Temperature Range......-40℃ to +125℃
DISCLAIMER
SG Micro Corp reserves the right to make any change in
circuit design, or specifications without prior notice.
SG Micro Corp
www.sg-micro.com
AUGUST 2022
2
2A High Efficiency
SGM61020
Synchronous Buck Converter
PIN CONFIGURATIONS
SGM61020P (TOP VIEW)
FB
1
2
6
5
PG
EN
GND
VIN
3
4
SW
SOT-563-6
SGM61020 (TOP VIEW)
SGM61020 (TOP VIEW)
EN
1
2
5
FB
FB
1
2
6
5
NC
EN
GND
GND
VIN
3
4
SW
SW
3
4
VIN
SOT-23-5
SOT-563-6
PIN DESCRIPTION
PIN
NAME
I/O
FUNCTION
SOT-23-5
SOT-563-6
Active High Enable Input Pin. Apply a logic low to shut down the device or
pull EN up to VIN pin to enable the device. Do not leave EN floating.
1
2
3
5
2
4
EN
GND
SW
I
G
P
Ground Pin.
Switching Node Output Pin. Connect to the output inductor.
Power Supply Input. Decouple VIN with at least 4.7μF ceramic capacitor
to GND, as close to the device as possible. (If the input voltage oscillates,
the input capacitance can be increased.)
Feedback Input. Connect a resistor divider between the output voltage
sense point and ground and tap it to the FB pin to set the output voltage.
4
5
3
1
VIN
FB
P
I
NC
No Connection. This pin can be left open or connected to GND.
—
—
6
Open-Drain Power Good Output Pin (SGM61020P Only). Pull it up with a
resistor to a positive voltage no more than 5.5V. It can be left open if not
used.
PG
O
NOTE: I = input, O = output, P = power, G = ground.
SG Micro Corp
www.sg-micro.com
AUGUST 2022
3
2A High Efficiency
SGM61020
Synchronous Buck Converter
ELECTRICAL CHARACTERISTICS
(VIN = 5V, TJ = +25℃, unless otherwise noted.)
PARAMETER
SYMBOL
CONDITIONS
MIN
TYP
MAX UNITS
Power Supply
Quiescent Current into VIN Pin
Shutdown Current into VIN Pin
Under-Voltage Lockout Threshold
Under-Voltage Lockout Hysteresis
Thermal Shutdown Threshold
Thermal Shutdown Hysteresis
Logic Interface
IQ
Not switching
EN = 0V
42
µA
ISD
0.03
2.30
100
150
130
1
µA
V
VUVLO
VHYS
VIN falling
2.40
mV
℃
℃
TJ rising
TJ falling
TJSD
High-Level Threshold at EN Pin
Low-Level Threshold at EN Pin
Soft Startup Time
VIH
VIL
tSS
VIN = 2.5V to 5.5V
0.98
0.86
800
1.20
V
V
VIN = 2.5V to 5.5V
0.40
Measure from 0 to 95% × VOUT (set)
µs
Output
SOT-23-5
SOT-563-6
SOT-23-5
SOT-563-6
SOT-23-5
SOT-563-6
0.588
0.594
0.600
0.600
100
78
0.612
0.606
Feedback Regulation Voltage
High-side FET On-Resistance
Low-side FET On-Resistance
VFB
V
mΩ
mΩ
RDSON
55
41
High-side FET Current Limit
Switching Frequency
SGM61020P Only
ILIM
fSW
2.8
3.2
3.6
0.4
A
VOUT = 2.5V
1.5
MHz
V
FB rising, referenced to VFB nominal
95% × VREF
90% × VREF
0.1
Power Good Threshold
VPG
V
VFB falling, referenced to VFB nominal
Power Good Low-Level Output Voltage
Input Leakage Current into PG Pin
Power Good Delay Time
VPG_OL
IPG_LKG
tPG_DLY
ISINK = 1mA
VPG = 5.0V
VFB falling
V
0.01
µA
µs
45
SG Micro Corp
www.sg-micro.com
AUGUST 2022
4
2A High Efficiency
SGM61020
Synchronous Buck Converter
TYPICAL PERFORMANCE CHARACTERISTICS
TA = +25℃, VIN = 5V, VOUT = 1.8V, L1 = 2.2μH, COUT = 10μF, unless otherwise noted.
PWM Operation
Power-Save Mode Operation
VSW
VOUT
IL
VSW
AC Coupled
AC Coupled
VOUT
IL
IOUT = 1A
IOUT = 0.1A
Time (500ns/div)
Time (1μs/div)
Startup and Shutdown with Load
Startup and Shutdown with Load
VEN
VEN
VOUT
VOUT
IL
IL
IOUT = 2A
IOUT = 0.1A
Time (500μs/div)
Time (500μs/div)
Load Transient
Load Transient
AC Coupled
AC Coupled
VOUT
VOUT
IL
IL
IOUT = 0.8A to 2A, C1 = 6.8pF
IOUT = 0.8A to 2A, C1 = 0pF
Time (5μs/div)
Time (5μs/div)
SG Micro Corp
www.sg-micro.com
AUGUST 2022
5
2A High Efficiency
SGM61020
Synchronous Buck Converter
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
TA = +25℃, VIN = 5V, VOUT = 1.8V, L1 = 2.2μH (DCR = 18mΩ), unless otherwise noted.
Efficiency vs. Load Current
Efficiency vs. Load Current
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
VIN = 2.5V
VIN = 2.5V
V
V
IN = 3.3V
IN = 5V
V
V
IN = 3.3V
IN = 5V
VOUT = 1.2V
VOUT = 1.8V
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Load Current (A)
Load Current (A)
Efficiency vs. Load Current
Efficiency vs. Load Current
100
95
90
85
80
75
70
65
60
100
95
90
85
80
75
70
65
60
VIN = 3.3V
IN = 5V
VOUT = 2.5V
VOUT = 3.3V
VIN = 5V
V
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
Load Current (A)
Load Current (A)
Load Regulation
VIN = 5V
Line Regulation
VOUT = 1.8V
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0.0
-0.2
1.00
0.75
0.50
0.25
0.00
-0.25
-0.50
-0.75
-1.00
VOUT = 1.8V
V
OUT = 3.3V
IOUT = 0.5A
I
I
OUT = 1A
OUT = 2A
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Load Current (A)
Input Voltage (V)
SG Micro Corp
www.sg-micro.com
AUGUST 2022
6
2A High Efficiency
SGM61020
Synchronous Buck Converter
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
TA = +25℃, VIN = 5V, VOUT = 1.8V, L1 = 2.2μH (DCR = 18mΩ), unless otherwise noted.
Switching Frequency vs. Load Current
VIN = 5V
Switching Frequency vs. Input Voltage
2.5
2.0
1.5
1.0
0.5
0.0
2.5
2.0
1.5
1.0
0.5
0.0
IOUT = 1A
VOUT = 1.2V
VOUT = 1.2V
V
V
V
OUT = 1.8V
OUT = 2.5V
OUT = 3.3V
V
V
V
OUT = 1.8V
OUT = 2.5V
OUT = 3.3V
0.0 0.2 0.4 0.6 0.8 1.0 1.2 1.4 1.6 1.8 2.0
2.5
3.0
3.5
4.0
4.5
5.0
5.5
Load Current (A)
Input Voltage (V)
SG Micro Corp
www.sg-micro.com
AUGUST 2022
7
2A High Efficiency
SGM61020
Synchronous Buck Converter
FUNCTIONAL BLOCK DIAGRAM
VIN
Current Sense
Soft-Start
PWM
Comparator
+
+
+
-
Control Logic
and Driver
R
S
SW
Q
-
VREF
gm
FB
VZCD
Zero Current Detect
GND
PG
Off-Time
Calculation
VREF × 95%
FB
Control Contains
UVLO, TSD, etc
+
-
EN
Figure 2. SGM61020/SGM61020P Block Diagram
DETAILED DESCRIPTION
Overview
Power Good Output (SGM61020P Only)
The PG pin is an open-drain output. PG requires a
pull-up resistor (e.g. 510kΩ). PG pin is pulled to GND
before the output voltage is above 95% of the nominal
voltage. After FB voltage reaches 95% of VREF, the PG
pin is pulled high immediately. When the FB voltage
drops below 90% of VREF, the PG pin will be pulled low
after a 45μs delay. Leave the PG pin unconnected
when not used.
The SGM61020 is a high efficiency Buck switching
converter optimized for handheld battery-powered
applications. It operates at a quasi-fixed frequency of
1.5MHz and uses adaptive off-time PWM control for the
moderate to heavy load range. This allows using a
small inductor and small capacitors for compact
designs. At light load condition, this device operates in
power-save mode to reduce the switching frequency
and losses for longer battery life. The power-save
mode quiescent current is 42μA (TYP) while the
shutdown current is only 0.03μA (TYP).
Table 1. PG Output Logic
PG Status
Reason
Conditions
High Z
Low
EN = High, VFB ≥ VPG
EN = High, VFB ≤ VPG
EN = Low
√
Under-Voltage Lockout Protection
When the input voltage is below the UVLO threshold
(2.3V, TYP), the device is shut down. If the input
voltage rises above the UVLO threshold plus a 100mV
hysteresis, the IC will restart.
Output Voltage
√
√
√
√
Shutdown by EN
Thermal Shutdown
UVLO
TJ > TJSD
1.4V < VIN < VUVLO
Power Supply Removal VIN ≤ 1.4V
√
Enable Input
The EN pin is a digital control that turns the converter
on and off states. Drive EN logic high to turn on the
device; drive it logic low to turn it off. Connect the EN
pin directly to a voltage source that can’t be higher than
the VIN pin. The EN input should not be left floating.
SG Micro Corp
www.sg-micro.com
AUGUST 2022
8
2A High Efficiency
SGM61020
Synchronous Buck Converter
DETAILED DESCRIPTION (continued)
If the load is still low, the output will go slightly higher
than normal again and the switches will be turned off. In
power-save mode, the output voltage is slightly higher
than nominal output voltage. This effect can be
mitigated by a larger output capacitor.
Soft Startup and Pre-biased Output
An 800μs internal soft-start circuit is designed to
prevent input inrush current and voltage drops during
startup. This circuit slowly ramps up the error amplifier
reference voltage (VREF = 0.6V) after exiting the
shutdown state or under-voltage lockout (UVLO). Slow
increase of the output voltage prevents the excessive
inrush current for charging the output capacitors and
creates a smooth output voltage rise. The other
advantage of a soft-start is avoiding supply voltage
drops especially on the high internal impedance
sources such as the primary cells and rechargeable
batteries.
Low Dropout Operation (100% Duty Cycle)
When the input voltage reduces, the on-time increases.
When the input voltage is lower than the regulation
output voltage, the output voltage drops, and the
SGM61020 goes into 100% duty cycle mode. The
high-side switch is always turned on, and the output
voltage is determined by the load current times the
R
DSON composed by the high-side switch and inductor.
The SGM61020 is also capable of starting with a
pre-biased output capacitor when it is powering up or
enabled. When the device is turning on, a bias on the
output may exist due to the other sources connected to
the load(s) such as multi-voltage ICs or simply because
of residual charges on the output capacitors. For
example, when a device with light load is disabled and
re-enabled, the output may not drop during the off
period and the device must restart under pre-biased
output condition. Without the pre-biased capability, the
device may not be able to startup properly. The output
ramp is automatically initiated with the bias voltage and
ramps up to the nominal output value.
Current Limit Protection
Limiting the switch current protects the switch itself and
also prevents over-current in the source and the
inductor. If the high-side (HS) switch current exceeds
the ILIM threshold, HS switch is turned off and the
low-side (LS) switch will be turned on to reduce the
inductor current and limit the peak.
Note that the measured peak current limit in the
closed-loop and open-loop (ILIM_OL) test conditions is
slightly different, mainly due to the current comparator
propagation delay.
Power-Save Mode (PSM)
Thermal Shutdown
At light load condition, the SGM61020 shifts to the PSM
mode and operates with pulse skip modulation to
reduce the switching frequency and minimize the
losses. It also shuts down most of the internal circuits in
PSM. In this mode, one or more PWM pulses are sent
to charge the output capacitor and then the switches
are kept off. The output capacitor voltage gradually
drops due to small load current and when it falls below
the nominal voltage threshold, the PWM pulses resume.
A thermal shutdown function is implemented to prevent
damage caused by excessive heat and power dissipation.
Once the junction temperature exceeds +150°C, the
device is shut down. The device is released from
shutdown automatically when the junction temperature
decreases by 20℃.
SG Micro Corp
www.sg-micro.com
AUGUST 2022
9
2A High Efficiency
SGM61020
Synchronous Buck Converter
APPLICATION INFORMATION
In this section, power supply design with the SGM61020 synchronous Buck converter and selection of the external
component will be explained based on the typical application that is applicable for various input and output voltage
combinations.
L1
2.2μH
VIN
VOUT
1.8V
VIN
EN
SW
2.5V to 5.5V
C1
4.7μF
C3
10μF
C4
NS
R1
C2
NS
200kΩ
SGM61020P
R3
510kΩ
FB
R2
PG
100kΩ
GND
Power Good
Figure 3. SGM61020P Application Example with 1.8V/2A Output
larger value can be selected to reduce the input current
ripple.
Design Requirements
Table 2 summarizes the requirements for this example
as shown in Figure 3. The selected components are
given in Table 3.
Inductor Selection
The important factors for inductor selection are
inductance (L1), saturation current (ISAT), RMS rating
(IRMS), DC resistance (DCR) and dimensions. Use
Equations 1 and 2 to find the inductor peak current
(IL_MAX) and peak-to-peak ripple current (∆IL) in static
conditions:
Table 2. Design Parameters for the Application Example
Design Parameter
Input Voltage
Example Value
2.5V to 5.5V
1.8V
Output Voltage
Output Current
≤ 2A
ΔIL
Output Ripple Voltage
< 30mV
(1)
IL_MAX = IO_MAX
+
2
Table 3. Selected Components for the Design Example
1−D
L× fSW
(2)
ΔIL = VOUT
×
Ref
C1
Description
Manufacturer
Murata
4.7µF, 10V, X7R, 0805, Ceramic
P/N: GRM21BR71A475ME51L
where:
C2, C4
C3
NS
Standard
Murata
IO_MAX is the maximum load current, D = VOUT/VIN represents
duty cycle and fSW is the switching frequency.
10µF, 10V, X7R, 0805, Ceramic
P/N: GRM21BR71A106KA73L
2.2µH Wire Wound, DCRMAX = 39mΩ,
ISAT should be higher than IL_MAX, and sufficient margin
should be reserved. Typically, the saturation current
above high-side current limit is enough, and a 10% to
30% ripple current is selected to calculate the
inductance. Larger inductance values reduce the ripple
current but lead to sluggish transient response.
ISAT(30%) = 4.9A, IRMS(40 ) = 3A,
℃
L1
Sunlord
4mm × 4mm × 3mm,
P/N: SWPA4030S2R2NT
Value Depends on VOUT, 200kΩ, 1%,
0603, 1/16W Chip Resistor
R1
Standard
R2
R3
100kΩ, 1%, 0603, 1/16W Chip Resistor
Standard
Standard
510kΩ, 5%, 0603, 1/16W Chip Resistor
Output Voltage Setting
Input Capacitor Selection (CIN)
Use Equation 3 to select the R1/R2 resistor divider to
set the VOUT. Select the R2 value less than 100kΩ to
compromise noise sensitivity and light load losses.
High frequency decoupling input capacitors with low
ESR are needed to circulate and absorb the high
frequency switching currents of the converter. Place
this capacitor right beside the VIN and GND pins. A
4.7μF ceramic capacitor with X5R or better dielectric
and 0805 or smaller size is sufficient in most cases. A
R1
R2
R
1
VOUT = VFB × 1+
= 0.6V × 1+
(3)
R2
SG Micro Corp
www.sg-micro.com
AUGUST 2022
10
2A High Efficiency
SGM61020
Synchronous Buck Converter
APPLICATION INFORMATION (continued)
Output Capacitor Selection (COUT
)
Output Filter Design
This device is capable to operate with low ESR ceramic
capacitors to get low voltage ripple and fast response.
10μF ~ 22μF × 2 capacitors with X7R or X5R dielectric
type are recommended. Minimum capacitance of
output ripple criteria can be calculated from Equation 4.
Table 4 can be used to select the proper LC filter
components for most design requirements. The
inductor initial tolerance can be as high as -30% to +20%
of the nominal value and proper current derating is
usually required. Bias voltage may cause significant
capacitance drops in the ceramic capacitors. The
effective deviation of a ceramic capacitor can be as
high as -50% to +20% of the nominal value.
ΔIL
(4)
COUT
>
8× fSW × VOUT _RIPPLE
For output capacitor selection, transient response and
loop stability should also be considered. To simplify
customer's design process, the inductor and output
capacitor combinations are recommended in Table 4.
L1 = 2.2µH, COUT = 10µF are the recommended values
for the typical application.
Layout Guidelines
A good printed-circuit-board (PCB) layout is a critical
element of any high performance design. Follow the
guidelines below for designing a good layout for the
SGM61020.
Table 4. Proper Output Capacitor and Inductor Combination
VOUT
L1
COUT
22µF
1µH
• Place the input capacitor close to the device with the
22µF × 2
22µF
0.9V
shortest possible connection traces.
2.2µH
1µH
22µF × 2
10µF
• Share the same GND return point for the input and
output capacitors and locate it as close as possible
to the device GND pin to minimize the AC current
loops. Place the inductor close to the switching node
and connect it with a short trace to minimize the
parasitic capacitances coupled to the SW node.
22µF
22µF × 2
10µF
1.8V
3.3V
2.2µH
2.2µH
22µF
• Keep the signal traces like the FB sense line away
22µF × 2
10µF
from SW or other noisy sources.
22µF
• Use GND planes in mid-layers for shielding and
minimizing the ground potential drifts.
22µF × 2
Refer to Figure 4 and Figure 5 for a recommended PCB
layout.
SG Micro Corp
www.sg-micro.com
AUGUST 2022
11
2A High Efficiency
SGM61020
Synchronous Buck Converter
APPLICATION INFORMATION (continued)
Top Layer
Bottom Layer
Figure 4. SOT-23-5 PCB layout
Top Layer
Bottom Layer
Figure 5. SOT-563-6 PCB layout
SG Micro Corp
www.sg-micro.com
AUGUST 2022
12
2A High Efficiency
SGM61020
Synchronous Buck Converter
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from REV.A (AUGUST 2022) to REV.A.1
Page
Updated Electrical Characteristics .......................................................................................................................................................................4
Changes from Original (MARCH 2022) to REV.A
Page
Changed from product preview to production data.............................................................................................................................................All
SG Micro Corp
www.sg-micro.com
AUGUST 2022
13
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
SOT-23-5
1.90
D
e1
2.59
E1
E
0.99
b
e
0.95
0.69
RECOMMENDED LAND PATTERN (Unit: mm)
L
A2
A
ccc
C
SEATING PLANE
A1
θ
c
C
0.25
Dimensions In Millimeters
Symbol
MIN
MOD
MAX
1.450
0.150
1.300
0.500
0.220
3.050
1.750
3.000
A
A1
A2
b
-
-
0.000
0.900
0.300
0.080
2.750
1.450
2.600
-
-
-
c
-
D
-
E
-
E1
e
-
0.950 BSC
e1
L
1.900 BSC
0.300
0°
-
-
0.600
8°
θ
ccc
0.100
NOTES:
1. This drawing is subject to change without notice.
2. The dimensions do not include mold flashes, protrusions or gate burrs.
3. Reference JEDEC MO-178.
SG Micro Corp
TX00033.001
www.sg-micro.com
PACKAGE INFORMATION
PACKAGE OUTLINE DIMENSIONS
SOT-563-6
D
e
b
E1
E
L1
L
0.30
0.50
A
A1
1.35
θ
0.45
θ
c
RECOMMENDED LAND PATTERN (Unit: mm)
Dimensions
In Millimeters
Dimensions
In Inches
Symbol
MIN
MAX
0.600
0.050
0.270
0.180
1.700
1.300
1.700
0.550
0.300
0.400
MIN
MAX
0.024
0.002
0.011
0.007
0.067
0.051
0.067
0.022
0.012
0.016
A
A1
b
0.525
0.000
0.170
0.090
1.500
1.100
1.500
0.450
0.100
0.200
0.021
0.000
0.007
0.004
0.059
0.043
0.059
0.018
0.004
0.008
c
D
E
E1
e
L
L1
θ
9° REF
9° REF
NOTES:
1. Body dimensions do not include mode flash or protrusion.
2. This drawing is subject to change without notice.
SG Micro Corp
TX00187.000
www.sg-micro.com
PACKAGE INFORMATION
TAPE AND REEL INFORMATION
REEL DIMENSIONS
TAPE DIMENSIONS
P2
P0
W
Q2
Q4
Q2
Q4
Q2
Q4
Q1
Q3
Q1
Q3
Q1
Q3
B0
Reel Diameter
P1
A0
K0
Reel Width (W1)
DIRECTION OF FEED
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF TAPE AND REEL
Reel Width
Reel
Diameter
A0
B0
K0
P0
P1
P2
W
Pin1
Package Type
W1
(mm)
(mm) (mm) (mm) (mm) (mm) (mm) (mm) Quadrant
SOT-23-5
7″
7″
9.5
9.5
3.20
1.78
3.20
1.78
1.40
0.69
4.0
4.0
4.0
4.0
2.0
2.0
8.0
8.0
Q3
Q3
SOT-563-6
SG Micro Corp
TX10000.000
www.sg-micro.com
PACKAGE INFORMATION
CARTON BOX DIMENSIONS
NOTE: The picture is only for reference. Please make the object as the standard.
KEY PARAMETER LIST OF CARTON BOX
Length
(mm)
Width
(mm)
Height
(mm)
Reel Type
Pizza/Carton
7″ (Option)
7″
368
442
227
410
224
224
8
18
SG Micro Corp
www.sg-micro.com
TX20000.000
相关型号：
©2020 ICPDF网 联系我们和版权申明