STR-K740P [SONY]
SERVICE MANUAL;型号: | STR-K740P |
厂家: | SONY CORPORATION |
描述: | SERVICE MANUAL |
文件: | 总19页 (文件大小:4233K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
STR-K740P/K840P
SERVICE MANUAL
US Model
Canadian Model
AEP Model
UK Model
Ver 1.0 2002. 02
E Model
Photo : STR-K840P (SILVER model)
• STR-K740P/K840P are the tuner and the
amplifier section in HT-DDW740/DDW840.
Dolby Laboratories Licensing Corporation.
“DOLBY” the double-D symbol ; “AC-3” and “PRO LOGIC”
are trademarks of Dolby Laboratories Licensing Corporation.
SPECIFICATIONS
POWER OUTPUT AND TOTAL
HARMONIC DISTORTION:
Models of area code AR, SP
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %)
With 8 ohm loads, both channels driven, from
40 – 20,000 Hz; rated 100 watts (STR-K840P
only)/80 watts (STR-K740P only) per channel
minimum RMS power, with no more than
0.09 % total harmonic distortion from 250
milliwatts to rated output (Models of area code
U only).
STR-K840P:
90 W + 90 W
Reference Power Output2)
(8 ohms 1 kHz, THD 10 %)
STR-K840P:
FRONT1): 120 W/ch
CENTER1): 120 W
SURR1): 120 W/ch
Models of other area code
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %)
STR-K840P:
STR-K740P:
Amplifier section
POWER OUTPUT
Models of area code U, CA
Rated Power Output at Stereo Mode
(8 ohms 40 Hz – 20 kHz, THD 0.09 %)
100 W + 100 W2)
80 W + 80 W2)
Reference Power Output2)
(8 ohms 1 kHz, THD 10 %)
STR-K840P:
STR-K840P:
STR-K740P:
100 W + 100 W
80 W + 80 W
FRONT1): 120 W/ch
CENTER1): 120 W
SURR1): 120 W/ch
FRONT1): 100 W/ch
CENTER1): 100 W
SURR1): 100 W/ch
Reference Power Output
(8 ohms 1 kHz, THD 0.7 %)
STR-K740P:
STR-K840P:
FRONT1):100 W/ch
CENTER1): 100 W
SURR1): 100 W/ch
FRONT1): 80 W/ch
CENTER1): 80 W
SURR1): 80 W/ch
1) Depending on the sound field settings and the
source, there may be no sound output.
2) Measured under the following conditions:
STR-K740P:
Area code
Power requirements
240 V AC, 50 Hz
230 V AC, 50 Hz
120 VAC, 60 Hz
Models of area code CEL,CEK
Rated Power Output at Stereo Mode
(8 ohms 1 kHz, THD 0.7 %)
STR-K840P:
STR-K740P:
E
SP, CEL, CEK, AR
MX
100 W + 100 W2)
80 W + 80 W2)
Reference Power Output2)
(8 ohms 1 kHz, THD 0.7 %)
STR-K840P:
FRONT1): 100 W/ch
CENTER1): 100 W
SURR1): 100 W/ch
FRONT1): 80 W/ch
CENTER1): 80 W
SURR1): 80 W/ch
— Continued on next page —
STR-K740P:
FM STEREO FM-AM RECEIVER
9-873-544-01
2002B1600-1
© 2002.02
Sony Corporation
Home Audio Company
Published by Sony Engineering Corporation
STR-K740P/K840P
Frequency response
AM tuner section
MULTI CH IN3), CD,
MD/TAPE, DVD/LD,
VIDEO 1, 2
10 Hz – 50 kHz
+0.5/–2 dB (with sound
field, and tone bypassed)
Tuning range
Models of area code U, CA
With 10-kHz tuning scale: 530 – 1710 kHz6)
With 9-kHz tuning scale: 531 – 1710 kHz6)
Models of area code E, AR, MX
With 10-kHz tuning scale: 530 – 1610 kHz6)
With 9-kHz tuning scale: 531 – 1602 kHz6)
Models of area code MY, SP, CEL, CEK
With 9-kHz tuning scale: 531 – 1602 kHz
Inputs (Analog)
MULTI CH IN3), CD,
MD/TAPE, DVD/LD,
VIDEO 1, 2
Sensitivity: 250 mV
Impedance: 50 kilohms
S/N4): 96 dB
(A, 250 mV5))
Antenna
Loop antenna
Intermediate Frequency
3) HT-DDW840 only
450 kHz
4) INPUT SHORT (with sound field and tone
bypassed).
5) Weighted network, input level.
Usable sensitivity
S/N
50 dB/m (at 1,000 kHz or
999 kHz)
54 dB (at 50 mV/m)
Inputs (Digital)
Sensitivity: –
Impedance: 75 ohms
S/N: 100 dB
DVD/LD (Coaxial)
Harmonic distortion 0.5 % (50 mV/m, 400 Hz)
Selectivity
(A, 20 kHz LPF)
At 9 kHz:
35 dB
40 dB
At 10 kHz:
Sensitivity: –
Impedance: –
S/N: 100 dB
VIDEO 2 (Optical)
6) You can change the AM tuning scale to 9 kHz or
10 kHz. After tuning in any AM station, turn off
the receiver. Hold down PRESET TUNING + and
(A, 20 kHz LPF)
press
. All preset stations will be erased when
Outputs
you change the tuning scale. To reset the scale to
10 kHz (or 9 kHz), repeat the procedure.
MD/TAPE (OUT),
VIDEO 1
(AUDIO OUT)
Voltage: 250 mV
Impedance: 10 kilohms
Video section
Inputs
SUB WOOFER
Voltage: 2 V
Impedance: 1 kilohms
Video:
1 Vp-p, 75 ohms
1 Vp-p, 75 ohms
Outputs
Video:
Tone
Gain levels:
±6 dB, 1 dB step
General
Power requirements
Area code
U, CA, MX
CEL, CEK
MY, SP, AR
E
FM tuner section
Tuning range
87.5 - 108.0 MHz
Power requirements
120 V AC, 60 Hz
Antenna terminals
75 ohms, unbalanced
230 V AC, 50/60 Hz
Intermediate Frequency
220 – 230 V AC, 50/60 Hz
120/220/240 V AC, 50/60 Hz
10.7 MHz
Sensitivity
Mono:
Stereo:
18.3 dBf, 2.2 µV/75 ohms
38.3 dBf, 22.5 µV/75 ohms
Power consumption
Area code
Power consumption
Usable sensitivity
11.2 dBf, 1 µV/75 ohms
U, MX
STR-K840P: 210 W
STR-K740P: 180 W
S/N
Mono:
Stereo:
76 dB
70 dB
CA
STR-K840P: 300 VA
STR-K740P: 260 VA
Harmonic distortion at 1 kHz
Mono:
Stereo:
0.3%
0.5%
CEL, CEK, MY, SP, STR-K840P: 180 W
E, AR STR-K740P: 155 W
Separation
45 dB at 1 kHz
Power consumption (during standby mode)
0.5 W
Frequency response 30 Hz – 15 kHz,
+0.5/–2 dB
Dimensions
430 145 298 mm
(16 7/8 5 6/8 11 6/8
inches) including
projecting parts and
controls
Selectivity
60 dB at 400 kHz
Mass (Approx.)
7.0 kg (15 lb 7 oz)
Design and specifications are subject to change
without notice.
•
Abbreviation
U
CA
: US model.
: Canadian model.
CEL : AEP model.
CEK : UK model.
SP
: Singapore model. (Malaysia model included.)
MX : Mexican model.
MY : Malaysia model.
AR
: Argentine model.
2
STR-K740P/K840P
Notes on chip component replacement
SAFETY CHECK-OUT
• Never reuse a disconnected chip component.
• Notice that the minus side of a tantalum capacitor may be
damaged by heat.
After correcting the original service problem, perform the
following safety checks before releasing the set to the customer:
Check the antenna terminals, metal trim, “metallized” knobs, screws,
and all other exposed metal parts for AC leakage. Check leakage as
described below.
Unleaded solder
Boards requiring use of unleaded solder are printed with the lead-
free mark (LF) indicating the solder contains no lead.
(Caution: Some printed circuit boards may not come printed with
the lead free mark due to their particular size.)
LEAKAGE
The AC leakage from any exposed metal part to earth ground
and from all exposed metal parts to any exposed metal part having
a return to chassis, must not exceed 0.5 mA (500 microamperes).
Leakage current can be measured by any one of three methods.
: LEAD FREE MARK
Unleaded solder has the following characteristics.
• Unleaded solder melts at a temperature about 40°C higher than
ordinary solder.
Ordinary soldering irons can be used but the iron tip has to be
applied to the solder joint for a slightly longer time.
Soldering irons using a temperature regulator should be set to
about 350°C.
Caution: The printed pattern (copper foil) may peel away if the
heated tip is applied for too long, so be careful!
• Strong viscosity
Unleaded solder is more viscous (sticky, less prone to flow) than
ordinary solder so use caution not to let solder bridges occur such
as on IC pins, etc.
1. A commercial leakage tester, such as the Simpson 229 or RCA
WT-540A. Follow the manufacturers’instructions to use these
instruments.
2. A battery-operated AC milliammeter. The Data Precision 245
digital multimeter is suitable for this job.
3. Measuring the voltage drop across a resistor by means of a
VOM or battery-operatedAC voltmeter. The “limit” indication
is 0.75 V, so analog meters must have an accurate low-voltage
scale. The Simpson 250 and Sanwa SH-63Trd are examples of
a passive VOM that is suitable. Nearly all battery operated
digital multimeters that have a 2V AC range are suitable. (See
Fig. A)
• Usable with ordinary solder
It is best to use only unleaded solder but unleaded solder may
also be added to ordinary solder.
To Exposed Metal
Parts on Set
AC
Voltmeter
(0.75 V)
0.15 µF
1.5 kΩ
Earth Ground
Fig. A. Using an AC voltmeter to check AC leakage.
SAFETY-RELATED COMPONENT WARNING!!
ATTENTION AU COMPOSANT AYANT RAPPORT
À LA SÉCURITÉ!
COMPONENTS IDENTIFIED BY MARK 0 OR DOTTED LINEWITH
MARK 0 ON THE SCHEMATIC DIAGRAMS AND IN THE PARTS
LIST ARE CRITICAL TO SAFE OPERATION. REPLACE THESE
COMPONENTS WITH SONY PARTS WHOSE PART NUMBERS
APPEAR AS SHOWN IN THIS MANUAL OR IN SUPPLEMENTS
PUBLISHED BY SONY.
LES COMPOSANTS IDENTIFÉS PAR UNE MARQUE 0 SUR LES
DIAGRAMMES SCHÉMATIQUES ET LA LISTE DES PIÈCES SONT
CRITIQUES POUR LA SÉCURITÉ DE FONCTIONNEMENT. NE
REMPLACER CES COMPOSANTS QUE PAR DES PIÈSES SONY
DONT LES NUMÉROS SONT DONNÉS DANS CE MANUEL OU
DANS LES SUPPÉMENTS PUBLIÉS PAR SONY.
3
STR-K740P/K840P
MODEL IDENTIFICATION
— BACK PANEL —
TABLE OF CONTENTS
1. GENERAL ·········································································· 5
2. TEST MODE ······································································ 6
3. DIAGRAMS········································································ 8
3-1. Circuit Board Location ·················································· 8
3-2. Block Diagrams – MAIN Section – ···························· 10
– DISPLAY/POWER Section –··································· 11
3-3. Printed Wiring Board – DIGITAL Section – ··············· 12
3-4. Schematic Diagram – DIGITAL Section (1/2) – ········· 13
3-5. Schematic Diagram – DIGITAL Section (2/2) – ········· 14
3-6. Printed Wiring Board – MAIN Section – ···················· 15
3-7. Schematic Diagram – MAIN Section (1/2) – ·············· 16
3-8. Schematic Diagram – MAIN Section (2/2) – ·············· 17
3-9. Printed Wiring Board – DISPLAY Section – ·············· 18
3-10.Schematic Diagram – DISPLAY Section – ················· 19
3-11.Printed Wiring Board – VIDEO Section – ·················· 20
3-12.Schematic Diagram – VIDEO Section – ····················· 20
3-13.Printed Wiring Board – POWER Section – ················· 21
3-14.Schematic Diagram – POWER Section – ··················· 22
3-15.IC Block Diagrams ······················································ 23
3-16.IC PIN FUNCTION DESCRIPTIONS ······················· 25
Parts No.
MODEL
K740P : US
PARTS No.
4-238-189-2s
4-238-189-3s
4-238-189-4s
4-238-189-5s
4-238-189-6s
4-238-189-7s
4-238-193-0s
4-238-193-1s
4-238-193-2s
4-238-193-3s
4-238-193-4s
4-238-193-5s
4-238-193-8s
4-238-193-9s
K740P : Canadian
K740P : Malaysia,Singapore
K740P : E
K740P : AEP
K740P : UK
K840P : US
K840P : Canadian
K840P : Malaysia, Singapore
K840P : E
K840P : AEP
4. EXPLODED VIEWS ······················································ 27
4-1. Front Panel Section ····················································· 27
4-2. Chassis Section-1 ························································ 28
4-3. Chassis Section-2 ························································ 29
K840P : UK
K840P : Argentine
K840P : Mexican
5. ELECTRICAL PARTS LIST ······································· 30
4
STR-K740P/K840P
SECTION 1
GENERAL
This section is extracted
from instruction manual.
FM MODE (Models of area code
CEL, CEK only) ed, (Except for
models of area code CEL, CEK)
ef(32)
PRESET TUNING +/– (Except
for models of area code CEL,
CEK) 3(33, 54)
PTY (models of area code CEL,
CEK only) ef(34)
ALPHABETICAL ORDER
0 – 9
2 CH wh(26)
INPUT MODE qg(22)
IR (receptor) 4(39, 46, 52)
LEVEL 0(16, 20, 28, 57)
SET UP 6(4, 16, 37, 57)
SHIFT eg(33)
SLEEP (HT-DDW740 only) qf
(37)
A – D
A.DEC wk(24, 26)
AM (Except for models of area
code CEL, CEK) es(31, 32)
BASS +/– wg(19, 30, 57)
CD ql(22)
CINEMA STUDIO EX A, B, C
9(25)
Digital Cinema Sound (indicator)
qs(24)
M
SURR qd(28, 57)
MASTER VOLUME wd(20, 50)
MD/TAPE qj(22)
MEMORY eh(31, 33)
T – Z
MENU +/– e;(16, 28, 36, 37, 57)
TREBLE +/– qh(30, 57)
TUNER ws(22, 32, 33, 36)
TUNING +/– 5(32)
VIDEO 1 qk(22)
MENU </> ea(16, 28, 36, 37, 57)
MODE wj(25, 30, 51)
MULTI CHANNEL DECODING
(indicator) (HT-DDW840 only)
7(22)
DIMMER ej(23)
DISPLAY 2(23, 34, 52)
Display qa(23)
VIDEO 2 w;(22)
MULTI CH IN (HT-DDW840
only) qf(22)
BUTTON DESCRIPTIONS
DVD/LD wa(22)
MUTING wf(22, 50)
?/1 (power) 1(4, 15, 20, 21,
E – L
30, 31, 54)
N – S
NAME 8(36)
PHONES (jack) ek(22, 51)
PRESET/PTY SELECT +/–
(Models of area code CEL, CEK
only) 3(33, 34)
ENTER wl(36)
•
Abbreviation
CEK : UK model.
CEL : AEP model.
FM (Except for models of area
code CEL, CEK) ed(31, 32)
FM/AM (Models of area code
CEL, CEK only) es(31, 32)
1
23
4
5
6
7 890qaqsqdqfqgqhqjqkqlw;waws
g
+
–
ek
ej
ehegefedesea e; wlwkwjwh wg
wf
wd
5
STR-K740P/K840P
SECTION 2
TEST MODE
3. Press the VIDEO button, confirm display
FACTORY PRESET MODE
* All preset contents are reset to the default setting.
* Procedure:
DIGITAL
DTS
MONO
NEWS
MEMORY
SP.OFF OPT MULTI CH IN
EQ
While depressing the VIDEO 1 and the 2CH buttons simul-
taneously, press the power button to turn on the main power.
C
dB
Hz
ft.
?/1
( ( (
SL
) ) )
SR
The message “FACTORY” appears and switch off the set.
While depressing the VIDEO 1 and the 2CH buttons simul-
taneously, press the power
“FACTORY” appears and the present contents are reset to the
default values.
button again. The message
?/1
MULTI CHANNEL DECODING , 2CH , SURR and NAME
LED turn on.
4. Press the VIDEO button, All segments turn off.
AM CHANNEL STEP 9 KHZ/10 KHZ
SELECTION MODE
* Either the 9 kHz step or 10 kHz step can be selected for the AM
channel step.
5. Every pressing of the VIDEO button turns on each
segment and LED one after another in the same order.
(Not only the VIDEO button, but also the other buttons such as
DVD/LD , TV/SAT , MD/TAPE , CD , TUNER and AUX can
be used.)
* Procedure:
Set the FUNCTION to AM. Turn off the main power.
While depressing the TUNING+ button or the
PRESET+ button, press the power
main power. Either the message “9 k STEP” or “10 k STEP”
appears. Select the desired step.
button to turn on the
?/1
SOUND FIELD CLEAR MODE
* The preset sound field is cleared when this mode is activated.
Use this mode before returning the product to clients upon
completion of repair.
* For US/Canadian/E model only
* Procedure:
SPEAKER SIZE SELECTION MODE
*Either Normal Speaker or Micro Satellite Speaker can be selected.
*Procedure:
While depressing the MODE button, press the power
to turn on the main power.
The message “SURR. CLR.” appears and initialization is
performed.
button
?/1
While depressing the LEVEL button, press the power
to turn the main power.
button
?/1
Either the message “NORM. SP.” or “MICRO SP.” is displayed.
Select the desired speaker size.
DEMONSTRATION MODE
* Demonstration is performed.
* Procedure :
FLUORESCENT INDICATOR TUBE TEST MODE
* All fluorescent segments are tested. When this test is activated,
all segments turn on at the same time, then each segment turns on
one after another.
While depressing the SET UP button, press the power
?/1
button. The message appears and demonstration is performed.
* To finish DEMONSTRATION MODE, press the power
?/1
button while the introduction message appears in the display.
* Procedure:
While depressing the MD/TAPE and the SHIFT buttons simul-
SOFTWARE VERSION DISPLAY MODE
* The software version is displayed.
* Procedure:
taneously, press the power
1. All segments turn on.
button to turn on the main power.
?/1
While depressing the ENTER and the A.F.D buttons
SLEEP D D
D
IGITALPRO LOGIC DTS MPEGSTEREO MONO RDS MEMORY
SW
L
SP.OFF OPT COAX MULTI CH IN D.RANGE EQ TA NEWS INFO
MUTING
simultaneously, press the power
button to turn on the main
?/1
C
R
power. The model name, destination and the software version are
displayed.
dB
kHz
mft.
MHz
( ( ( L F E ) ) )
SL SR
S
KEY CHECK MODE
* Button check
* Procedure:
MULTI CHANNEL DECODING , Digital Cinema Sound ,
A.F.D. , MODE , 2CH and SET UP LED turn on.
2. Press the VIDEO button, confirm display.
While depressing the VIDEO 1 and the SHIFT buttons
simultaneously, press the power
power.
button to turn on the main
?/1
SLEEP
R
D
D
COAX
PRO LOGIC
MPEGSTEREO
D.RANGE TA
RDS
INFO
SW
L
MUTING
“REST 39” appears. (AEP, UK, model: “RESET 38”)
Every pressing of any button other than ?/1 and SPEAKERS
counts down the buttons. The buttons which are already counted
once are not counted again. When all buttons are pressed “REST
00” appears.
L F E
k
m
MHz
S
When MASTER VOLUME is rotated in clockwise direction,
“VOL MIN”, “VOL 1” to “VOL 48”, “VOL MAX” appear.
A.F.D. , MODE , LEVEL , SET UP , and Digital Cinema Sound
LED turn on.
6
STR-K740P/K840P
AUTO BETICAL MODE
* This mode is installed in the Europe models only. When this mode
is used, the receiver scans the broadcasts that can be received by
the tuner, and sets up the broadcasts. Be sure to start scanning
after connecting the antenna.
* Procedure:
1. Check that the antenna is connected.
2. Press the ?/1 button to turn on the power while pressing the
MEMORY button.
3. The message “AUTO-BETICAL SELECT” appears and the
receiver starts scanning.
7
STR-K740P/K840P
SECTION 3
DIAGRAMS
3-1. Circuit Board Location
AC SELCT board (E model only)
STANDBY board
VIDEO board
POWER SW board
MAIN board
DIGITAL board
HEADPHONE board
DISPLAY board
8
STR-K740P/K840P
For printed wiring boards.
Note:
• X : parts extracted from the component side.
THIS NOTE IS COMMON FOR PRINTED WIRING
BOARDS AND SCHEMATIC DIAGRAMS.
(In addition to this necessary note is printed in each
block.)
• Waveform
DIGITAL Board
a
•
•
•
: Through hole.
: internal component.
: Pattern from the side which enables seeing.
f
For schematic diagrams.
1IC1101 wa(XOUT)
Note:
• All capacitors are in µF unless otherwise noted. p : pF. 50
WV or less are not indicated except for electrolytics and
tantalums.
C
4.4Vp-p
3.3Vp-p
2.8Vp-p
Q
These are omitted.
• All resistors are in Ω and 1/4 W or less unless otherwise
specified.
B E
81ns
(12.288MHz)
•
•
%
f
: indicates tolerance.
: internal component.
• 2 : nonflammable resistor.
• 5 : fusible resistor.
• C : panel designation.
B
C
E
These are omitted.
Note:
Note:
2IC1201 9(MCLK1)
The components identified by
mark 0 or dotted line with mark
0 are critical for safety.
Replace only with part number
specified.
Les composants identifiés par
une marque 0 sont critiques
pour la sécurité.
Ne les remplacer que par une
pièce portant le numéro spécifié.
Caution:
Pattern face side: Parts on the pattern face side seen from
(Side A)
the pattern face are indicated.
Parts on the parts face side seen from
the parts face are indicated.
Parts face side:
(Side B)
• A : B+ Line.
• B : B– Line.
• Voltages and waveforms are dc with respect to ground
under no-signal (detuned) conditions.
No mark : FM
• Voltages are taken with aVOM (Input impedance 10 MΩ).
Voltage variations may be noted due to normal produc-
tion tolerances.
• Waveforms are taken with a oscilloscope.
• Circled numbers refer to waveforms.
• Signal path.
73ns (13.59MHz)
3IC1601 id(XI)
F
J
c
: FM
: CD (ANALOG)
: DVD (DIGITAL)
• Abbreviation
5ns (20MHz)
CND : Canadian model
MY
SP
AR
MX
: Malaysia model
: Singapore model
: Argentine model
: Mexican model
9
9
STR-K740P/K840P
3-2. Block Diagrams – MAIN Section –
IC201
ANALOG SOUND
PROC.
TUNER PACK
FM
L CH
R CH
1
2
L IN8
75 Ω
IC1601(1/3)
COAXIAL
FM
R-CH
SYSTEM CONTROL.
ANTENNA
AM
AM ST-DO
ST-DI
76 DO
J402
J403
J404
L OUT 51
L
CLK
CD
IN
L IN9
Q361
MUTING
CE
78 SLATCH
67 L REC3
OUT
STEREO
TUNED
74 STEREO
73 TUNED
75 MUTING
MD/TAPE
DVD/LD
MUTING
AEP, UK
71 L IN7
IN
RDS-DATA
53 RDS DATA
RDS-INT
FM SIG OUT
52 RDS CLOCK
43 RDS SIGNAL
AUDIO IN
69
L IN5
SL
SL OUT 47
VIDEO 2
VIDEO 1
AUDIO IN
AUDIO OUT
AUDIO IN
63 L IN2
61 L REC1
62 L IN1
Q365
MUTING
A
IC103
VIDEO SELECT
J201
J200
VIDEO OUT
VIDEO IN
MONITOR
VIDEO 1
1
M.OUT
90
89
88
87
SW1 14
SW1
SW2
SW3
SW4
J401
13 V1
FRONT
SURROUND
SUB WOOFER
CENTER
11 AL IN
SW2 10
13
C
ASL IN
C OUT 39
MULTI
CH IN
VIDEO OUT
VIDEO IN
VIDEO IN
15
5
V1 OUT
V2
Q363
16 ASW IN
15 AC IN
SW3
4
MUTING
VIDEO 2
DVD/LD
SW4
SW5
6
2
IC1101
3
DVD
DIGITAL AUDIO
I/F RECEIVER
D204
J1101
IC1102
IC1102
10
AL OUT
D203
3
5
6
2
DVD/LD
IN
COAXIAL
OPTICAL
IC1501
5
4
DIN2
AUDIO CODEC
IC1502
-
6
7
29 LIN-
30
L OUT1 27
L OUT2 25
L OUT3 23
R OUT3 24
27 DL IN
29 DSL IN
31 DC IN
32 DSW IN
IC1502
-
IC1201
SW
SW OUT 35
2
1
DIGITAL
AUDIO DSP
LIN+
39 MCLKI
Q364
MUTING
CK OUT 13
22 KFSI0 SCK OUT 14
IC1105
BCK 14
29 BCKI2
BCKO1 20
4
5
BCK
VIDEO 2
IN
OPTICAL
IN
DIN1
LRCK 15
28 LRCKI2 LRCKO 19
LRCK
SDI1 18
SDO1 23
9
SDTO
6
7
8
SDTI1
SDTI2
SDTI3
SDO2 24
SDO3 25
DATAO 16
AUDIO 24
30 SDI2
D1101
20 DATA
21 CLK
35 DO
36 DI
43 CDT1
42 CCLK
41 CS
22 LATCH
69 GP8
68 GP9
IC1202
SRAM
38 CLK
37 CE
35
33
HD OUT
HD IN
34 ERROR
17 XSTATE
48 XMODE
47 CKSEL1
17 PD
3
S.MUTE
34 HCLK
36 HCS
Q1601,1602
Q379
MUTING
CONT
MUTING
SWITCH
32 HACN
PM
113
XIN XOUT
22
21
56 BST
MCLK1
9
X1201
13.5MHz
2
XRST
MCLK2 12
X1101
12.288MHz
59
EXLOCK
IC1604
EEPROM
SDA
5
SCL
6
D1601
• R-CH is omitted due to same as L-CH.
• Signal Path
+3.3V
98 97 95 96 99 100 93 94
1
2
18 19 20
4
5
7
3
6
10 12 13
8
9
14 15 16
24
21
34
33
CNS3
MD0
MD0 49
MD2 51
: FM
VDD
MD2
FOR
FLASH
PROGRAMMING
: CD(ANALOG)
: DVD (DIGITAL)
FLASH 1
FLASH 2
RESET
IC1601(2/3)
SYSTEM CONTROL
SP SWITCH/FLASH 1 28
FLASH 2 27
B
10
10
STR-K740P/K840P
– DISPLAY/POWER Section –
R-CH
J791
IC701
PHONES
POWER AMP
RY791
RY701
Q790
RELAY
DRIVE
Q703
+V OUT2 12
BOOSTER
Q701,702
LIMITER
TM602
L
L
8
1
NF2
IN2
9
• R-CH is omitted due to same as L-CH
• Signal Path
FRONT
D731
D733
D734
Q740
Q710
RELAY
DRIVE
R-CH
R
MUTING
AF POWER
PROTECT
: FM
Q705,706
CURRENT
DETECT
Q704
BOOSTER
-V OUT2 11
IC702
POWER AMP
SPEAKERS
Q653
BOOSTER
+V OUT2 12
TM601
SR
Q651,652
LIMITER
R-CH
SURROUND
CENTER
SL
SL
C
8
1
IN2 NF2
MUTING
9
RY601
Q640
AF POWER
PROTECT
Q610
RELAY
DRIVE
Q655,656
CURRENT
DETECT
Q654
BOOSTER
-V OUT2 11
A
POWER AMP
IC501
Q503
BOOSTER
+V OUT
6
2
5
Q501,502
LIMITER
C
1
IN-
IN+
RY501
Q550
RELAY
DRIVE
Q540
AF POWER
PROTECT
IC1901
Q505,506
CURRENT
DETECT
Q504
BOOSTER
-V OUT
+3.3V
REG
+3.3V
+2.5V
+5V
2
5
3
4
1
D721
+2.5V
REG
Q722,723,725
T901
D902-905
FL101
PROTECT
SWITCH
IC1903
J405
IC401
FLUORESCENT
INDICATOR TUBE
+5V
REG
SUB
WOOFER
5
7
AUDIO
OUT
SW
RY560
Q560
RELAY
DRIVE
F1
F2
IC100
FL DRIVE
Q747,748
POWER
14 29
42 31
D111-114
MUTING
SEG1-16 GRID1-12
SW1
SW2
SW3
SW4
1
2
3
4
Q107-111
LED
DRIVE
D802
+B
-B
7
8
9
POWER AMP
Q691,692
-B SW
D100-104
-B
IC601
IC601
2
1
5
7
FL101
-30V
Q801
-30V REG
IC101
BUFFER
D820-823
Q100-104
LED DRIVE
RELAY
+B
IC801
AUDIO
+7V
+7V
1
3
3
3
3
3
3
2
1
2
1
1
REG
Q471
+3.3V
D899
D898
+3.3V REG
IC802
61 62 63
29 30 31 32 26
22
67
68
72
70
71
69
25
AUDIO
-7V
-7V
REG
K740P:E/K840P:E MODEL ONLY
S901
IC807
IC1503
+5V
REG
FUSE DETECT 55
SIRCS 54
VIDEO
+5V
+5V
REG
AUDIO
+5V
3
1
1
IC102
VOLTAGE
SELECTOR
IC804
REMOTE
CONTROL
RECEIVER
K740P:AEP,UK
K840P:AEP,UK
VIDEO
-5V
-5V
REG
1
F1
F2
g
SYSTEM CONTROL
IC1601(3/3)
IC1905
IC1902
F901
TUNER
+3.3V
TUNER
+10V
+3.3V
REG
+10V
REG
3
AVCC 35
VCC3 84
VCC5 23
+3.3V(STBY)
IC1904
+3.3V
REG
IC1602
RESET
1
2
T902
RSTX 77
STOP 48
D910-913
Q921
AC DET
AC
IN
82
83
38
39
40
41
59 60
56
66
D914
Q901
D915
X1601
20.0MHz
RESET
3
1
B
S145
?/1
RY901
FUNCTION
KEY
FUNCTION
KEY
FUNCTION
KEY
FUNCTION
KEY
ENCODER
RELAY
DRIVE
S100-109
S110-119
S120-128
S130-137,
S143,144
RV102
MASTER
VOLUME
11
11
STR-K740P/K840P
• See page 9 for Waveform. • See page 23 for IC Block Diagrams.
3-4. Schematic Diagram – DIGITAL Section (1/2) –
IC B/D
13
13
STR-K740P/K840P
• See page 9 for Waveform. • See page 25 for IC Pin Function Description.
3-5. Schematic Diagram – DIGITAL Section (2/2) –
14
14
STR-K740P/K840P
• See page 23 for IC Block Diagrams.
3-7. Schematic Diagram – MAIN Section (1/2) –
13
16
16
STR-K740P/K840P
• See page 23 for IC Block Diagrams.
3-8. Schematic Diagram – MAIN Section (2/2) –
IC B/D
IC B/D
IC B/D
17
17
STR-K740P/K840P
• See page 24 for IC Block Diagrams.
3-10. Schematic Diagram – DISPLAY Section –
IC B/D
19
19
STR-K740P/K840P
• See page 24 for IC Block Diagrams.
•
: Uses unleaded solder.
3-11. Printed Wiring Board – VIDEO Section –
• See page 8 for Circuit Boards Location.
3-12. Schematic Diagram – VIDEO Section –
IC807
IC B/D
IC804
IC103
20
20
STR-K740P/K840P
• See page 8 for Circuit Boards Location.
•
: Uses unleaded solder.
3-13. Printed Wiring Board – POWER Section –
K740P:US, CND/K840P:US, CND
(CHASSIS)
EXCEPT K740P:E/K840P:E
K740P:E/K840P:E
3
2
1
H
5
4
3
CNP801
(Page 15)
J
2
1
CNP802
(Page 15)
3
2
1
21
21
STR-K740P/K840P
3-14. Schematic Diagram – POWER Section –
F901
2.5V/250V : EXCEPT K740P:US,CND/K840P:US,CND,MX
6.3V/125V : K740P:US,CND/K840P:US,CND,MX
22
22
相关型号:
STR-L400
Power IC for Quasi-Resonant Type Switching Power Supply with High Efficiency, Low Noise
SANKEN
STR-L451
Power IC for Quasi-Resonant Type Switching Power Supply with High Efficiency, Low Noise
SANKEN
STR-L472
Power IC for Quasi-Resonant Type Switching Power Supply with High Efficiency, Low Noise
SANKEN
STR-L6400
Power IC for Quasi-Resonant Type Switching Power Supply with High Efficiency, Low Noise
SANKEN
STR-L6472
Power IC for Quasi-Resonant Type Switching Power Supply with High Efficiency, Low Noise
SANKEN
©2020 ICPDF网 联系我们和版权申明