BQ25071DQCT [TI]
bq25071 1-A, Single-Input, Single-Cell LiFePO4 Linear Battery Charger with 50 mA LDO;型号: | BQ25071DQCT |
厂家: | TEXAS INSTRUMENTS |
描述: | bq25071 1-A, Single-Input, Single-Cell LiFePO4 Linear Battery Charger with 50 mA LDO 电池 光电二极管 |
文件: | 总26页 (文件大小:1087K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
bq25071
SLUSBK6 –JULY 2014
bq25071 1-A, Single-Input, Single-Cell LiFePO Linear Battery Charger with 50 mA LDO
4
1 Features
3 Description
The bq25071 is a highly integrated, linear, LiFePO4
battery charger targeted at space-limited portable
applications. It accepts power from either a USB port
or AC adapter and charges a single-cell LiFePO4
battery with up to 1 A of charge current. The 30 V
input rating with 10.5 V input overvoltage protection
supports low-cost unregulated adapters.
1
•
•
Single Cell LiFePO4 Charging Algorithm
30V Input Rating, With 10.5 V Overvoltage
Protection (OVP)
•
•
50mA Integrated Low Dropout Linear Regulator
(LDO)
Programmable Charge Current Through ISET and
EN Terminals
The bq25071 has
a single power output that
simultaneously charges the battery and powers the
system. The input current is programmable from 100
mA up to 1 A using the ISET input or configurable for
USB500. There is also a 4.9 V ±10% 50 mA LDO
integrated into the IC for supplying low power
external circuitry.
•
•
•
•
•
7% Charge Current Regulation Accuracy
Thermal Regulation and Protection
Soft-Start Feature to Reduce Inrush Current
Battery NTC Monitoring
Charging Status Indication
The LiFePO4 charging algorithm removes the current
taper typically seen as part of the constant voltage
mode control used in Li-Ion battery charge cycles
which reduces charge time significantly. Instead, the
battery is fast charged to the overcharge voltage and
then allowed to relax to a lower float charge voltage
threshold. The charger integrates the power stage
with the charge current and voltage sense to achieve
a high level of accuracy in the current and voltage
regulation loops. An internal control loop monitors the
IC junction temperature through the charge cycle and
reduces the charge current if an internal temperature
threshold is exceeded.
2 Applications
•
•
•
•
Smart Phones
Mobile Phones
Portable Media Players
Low Power Handheld Devices
Device Information(1)
PART NUMBER
PACKAGE
BODY SIZE (NOM)
bq25071
WSON (10)
2.00mm x 3.00mm
(1) For all available packages, see the orderable addendum at
the end of the datasheet.
4 Application Schematic
Pull-Up
bq25071
STATUS
USB or TA
CHG
OUT
VBUS
GND
D+
IN
VDD
D-
ABB
EN
BAT
TS
PACK+
TEMP
ISET
GND
PACK-
VCHG DET
USB DET
LDO
PWRPD
VUSBIN
ACDET
GPIO
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
bq25071
SLUSBK6 –JULY 2014
www.ti.com
Table of Contents
9.1 Overview ................................................................... 8
9.2 Functional Block Diagram ......................................... 9
9.3 Feature Description................................................. 10
9.4 Device Functional Modes........................................ 12
10 Application and Implementation........................ 14
10.1 Application Information.......................................... 14
10.2 Typical Application ............................................... 14
11 Power Supply Recommendations ..................... 17
12 Layout................................................................... 17
12.1 Layout Guidelines ................................................. 17
12.2 Layout Example .................................................... 17
13 Device and Documentation Support ................. 19
13.1 Trademarks........................................................... 19
13.2 Electrostatic Discharge Caution............................ 19
13.3 Glossary................................................................ 19
1
2
3
4
5
6
7
8
Features.................................................................. 1
Applications ........................................................... 1
Description ............................................................. 1
Application Schematic .......................................... 1
Revision History..................................................... 2
Device Comparison Table..................................... 3
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
8.1 Absolute Maximum Ratings ..................................... 4
8.2 Handling Ratings....................................................... 4
8.3 Recommended Operating Conditions....................... 4
8.4 Thermal Information.................................................. 4
8.5 Electrical Characteristics........................................... 5
8.6 Timing Requirements................................................ 6
8.7 Typical Characteristics.............................................. 7
Detailed Description .............................................. 8
14 Mechanical, Packaging, and Orderable
9
Information ........................................................... 19
5 Revision History
DATE
REVISION
NOTES
July 2014
*
Initial release.
2
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
6 Device Comparison Table
PART NUMBER
bq25071DQCR
bq25071DQCT
VBAT(OVCH)
3.7 V
VBAT(FLOAT)
3.5 V
V(OVP)
10.5 V
10.5 V
V(LDO)
4.9 V
4.9 V
3.7 V
3.5 V
7 Pin Configuration and Functions
bq25071
(TOP VIEW)
IN
ISET
1
2
3
10
9
OUT
GND
CHG
8
GND
LDO
TS
4
5
7
6
EN
BAT
10-pin 2mm x 3mm DFN
Pin Functions
PIN
NAME
I/O
DESCRIPTION
NO.
Input power supply. IN is connected to the external DC supply (AC adapter or USB port). Bypass IN to GND
with at least a 0.1 μF ceramic capacitor.
IN
1
I
Input current programming bias pin. Connect a resistor from ISET to GND to program the input current limit
when the user programmable mode is selected by grounding the EN pin. The resistor range is between 1 kΩ
and 10 kΩ to set the current between 100 mA and 1 A.
ISET
2
O
GND
LDO
3, 9
4
–
Ground pin. Connect to the thermal pad and the ground plane of the circuit.
LDO output. LDO is regulated to 4.9V and drives up to 50 mA. Bypass LDO to GND with a 0.1 μF ceramic
O
capacitor. LDO is enabled when V(UVLO) < VIN < V(OVP)
.
Battery pack NTC monitoring input. Connect a resistor divider from LDO to GND with TS connected to the
center tap to set the charge temperature window. The battery pack NTC is connected in parallel with the
bottom resistor of the divider. See the Detailed Design Procedure section for details on the selecting the
proper component values.
TS
5
6
7
I
I
I
BAT
EN
BAT is the sense input for the battery voltage. Connect BAT and OUT to the battery.
Enable input. Drive EN high to disable the IC. Connect EN to GND to place the bq25071 in the user
programmable mode using the ISET input where the input current is programmed. Leave EN floating to place
the bq25071 in USB500 mode. See the Input Current Limit Control (EN) section for details on using the EN
interface.
Charge status indicator open-drain output. CHG is pulled low while the device is charging the battery. CHG
goes high impedance when the battery is fully charged.
CHG
OUT
8
O
O
System output connection. Bypass the OUT to GND with a 1 μF ceramic capacitor. Connect OUT and BAT
together.
10
There is an internal electrical connection between the exposed thermal pad and the GND pin of the device.
The thermal pad must be connected to the same potential as the GND pin on the printed circuit board. Do not
use the thermal pad as the primary ground input for the device. GND pin must be connected to ground at all
times.
Thermal
Pad
Pad
–
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
8 Specifications
8.1 Absolute Maximum Ratings(1)
over operating free-air temperature range (unless otherwise noted)
MIN
–0.3
–0.3
–0.3
MAX
30
UNIT
V
IN (with respect to GND)
Input Voltage
EN, TS (with respect to GND)
7
V
Output Voltage
BAT, OUT, LDO, CHG, ISET (with respect to GND)
7
V
Input Current (Continuous)
Output Current (Continuous)
Output Current (Continuous)
Output Sink Current
IN
1.2
1.2
100
5
A
BAT
LDO
CHG
A
mA
mA
°C
Junction temperature, TJ
–40
150
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability. All voltage
values are with respect to the network ground pin unless otherwise noted.
8.2 Handling Ratings
MIN
MAX
UNIT
°C
TSTG
Storage temperature
Electrostatic discharge
–65
150
Human body model (HBM), per ANSI/ESDA/JEDEC
JS-001, all pins
V
0
0
3000
1000
(1)
VESD
Charged device model (CDM), per JEDEC
V
(2)
specification JESD22-C101, all pins
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
8.3 Recommended Operating Conditions
MIN
3.75(1)
3.75(1)
MAX UNITS
IN voltage
28
V
VIN
IIN
IN operating voltage
Input current, IN
10.2
1
1
A
A
IOUT Output Current in charge mode, OUT
TJ Junction Temperature
0
125
°C
(1) Charge current may be limited at low input voltages due to the dropout of the device.
8.4 Thermal Information
bq25071
THERMAL METRIC(1)
UNIT
DQC (10 PINS)
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
61.6
65.5
22.8
1.5
RθJC(top)
RθJB
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
ψJB
22.7
5.5
RθJC(bot)
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
4
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
8.5 Electrical Characteristics
Over junction temperature range 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNITS
INPUT
V(UVLO)
Under-voltage lock-out
Hysteresis on V(UVLO)
VIN: 0 V → 4 V
3.15
3.30
250
3.55
V
VHYS(UVLO)
VIN: 4 V → 0 V
mV
Input power good if VIN > VBAT
VIN(SLP)
V(BAT) = 3.6 V, VIN: 3.5 V → 4 V
+
Valid input source threshold VIN(SLP) above
VBAT
VIN(SLP)
30
18
75
150
54
mV
VHYS(INSLP)
tDGL(NO-IN)
Hysteresis on VIN(SLP)
V(BAT) = 3.6 V, VIN: 4 V → 3.5 V
32
32
mV
ms
Delay time, input power loss to charger turn-
off
Time measured from VIN: 5 V → 2.5 V
1 μs fall-time
VOVP
Input over-voltage protection threshold
Hysteresis on OVP
VIN: 5 V → 11 V
VIN: 11 V → 5 V
10.2
10.5
100
10.8
V
VHYS(OVP)
mV
QUIESCENT CURRENT
IBAT(PDWN)
Battery current into BAT, No input connected VIN = 0 V(1), V(CHG) = Low, TJ = 85°C
6
0.25
0.5
2
μA
EN = HI, VIN = 5.5V
IIN(STDBY)
Standby current into IN pin
EN = HI, VIN ≤ V(OVP)
mA
EN = HI, VIN > V(OVP)
BATTERY CHARGER FAST-CHARGE
TA = 0°C to 125°C, IOUT = 50 mA
TA = 25°C
3.455
3.455
3.62
100
3.5 3.545
3.5 3.539
VBAT(REG)
Battery charge regulation voltage
V
VBAT(OVCH)
IIN(RANGE)
Battery overcharge voltage threshold
3.7
3.78
1000
500
V
User programmable input current limit range
R(ISET) = 1 kΩ to 1 0kΩ, EN = VSS
EN = FLOAT
mA
435
467
IIN(LIM)
Input current limit, or fast-charge current
mA
EN = VSS
KISET/RISET
KISET
Fast charge current factor
VIN – VOUT
R(ISET) = 1 kΩ to 10 kΩ, EN = VSS
VIN = 3.55 V, IOUT = 0.75 A
900
1000
500
1100
900
AΩ
VDO(IN-OUT)
mV
ISET SHORT CIRCUIT PROTECTION
R(ISET): 900 Ω → 300 Ω, IOUT latches
RISET(MAX)
Highest resistor value considered a short fault off, Cycle power to reset, Fault range >
1.10 A
430
700
2
Ω
Maximum OUT current limit regulation
(Clamp)
IOUT(CL)
1.07
A
PRE-CHARGE AND CHARGE DONE
V(LOWV)
Pre-charge to fast-charge transition threshold
0.5
0.7
45
0.9
V
Precharge current to BAT during precharge
mode
I(PRECHARGE)
V(BAT) = 0 V to 0.7 V
V(BAT) falling
41.5
48.5
mA
RECHARGE OR REFRESH
V(RCH)
Recharge detection threshold
3.1
3.3
4.9
3.5
5.1
V
LDO
VIN = 5 V to 10.5 V,
I(LDO) = 0 mA to 50 mA
V(LDO)
LDO Output Voltage
4.7
60
V
I(LDO)
V(DO)
Maximum LDO Output Current
Dropout Voltage
mA
mV
VIN = 4.5V, I(LDO) = 50 mA
200
350
(1) Force V(CHG)
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
Electrical Characteristics (continued)
Over junction temperature range 0°C ≤ TJ ≤ 125°C and recommended supply voltage (unless otherwise noted)
PARAMETER
LOGIC LEVELS ON EN
TEST CONDITIONS
MIN
TYP
MAX UNITS
VIL
Logic low input voltage
Logic high input voltage
Logic FLOAT input voltage
0.4
V
V
VIH
1.4
V(FLT)
600
850
1100
1
mV
Maximum leakage sink or source current to
keep in FLOAT
I(FLTlkg)
µA
µA
Minimal drive current from an external device
for Low or High
IEN(DRIVE)
8
BATTERY-PACK NTC MONITOR (TS)
V(COLD)
V(CUTOFF)
V(HOT)
TS Cold Threshold
V(TS) Rising
24.5
12
25
1
25.5 %VLDO
%VLDO
TS Cold Cutoff Threshold
TS Hot Threshold
V(TS) Falling
V(TS) Falling
V(TS) Rising
12.5
1
13 %VLDO
%VLDO
VHOT(HYS)
CHG OUTPUT
VOL
TS Hot Cutoff Threshold
Output LOW voltage
Leakage current
I(SINK) = 1 mA
CHG = 5 V
0.45
1
V
IIH
μA
THERMAL REGULATION
TJ(REG)
Temperature Regulation Limit
TJ rising
TJ rising
TJ falling
125
155
20
°C
°C
°C
TJ(OFF)
Thermal shutdown temperature
Thermal shutdown hysteresis
TJ(OFF-HYS)
8.6 Timing Requirements
MIN
TYP
MAX
UNIT
INPUT
tBLK(OVP)
Input overvoltage blanking time
Input overvoltage recovery time
100
100
μs
μs
Time measured from VIN: 11 V → 5 V
1 μs fall-time to LDO = HI,
V(BAT) = 3.5 V
tREC(OVP)
ISET SHORT CIRCUIT PROTECTION
Deglitch time transition from I(SET)
short to IOUT disable
PRE-CHARGE AND CHARGE DONE
Deglitch time on pre-charge to fast-
tDGL(SHORT)
Clear fault by cycling V(BUS) or EN
1.5
ms
tDGL1(LOWV)
25
25
ms
ms
charge transition
Deglitch time on fast-charge to pre-
charge transition
tDGL2(LOWV)
RECHARGE OR REFRESH
Deglitch time, recharge threshold
detected
BATTERY-PACK NTC MONITOR (TS)
tDGL(RCH)
V(BAT) falling to New Charge Cycle
Fault detected on TS to stop charge
25
25
ms
ms
tdgl(TS)
Deglitch for TS Fault
6
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
8.7 Typical Characteristics
VIN = 5 V, VBAT = 3.2 V, I(CHG) = 280 mA, Typical Application Circuit
4
3.5
3
1.6
1.4
1.2
1
1.5
1.4
1.3
1.2
1.1
1
V(BAT)
V(CHG)
I(BAT)
2.5
2
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
0.8
0.6
0.4
0.2
0
1.5
1
0.5
0
0:00:00
1:12:00
2:24:00 3:36:00
Elapsed Time (hh:mm:ss)
4:48:00
0
25
50 75
Temperature (°C)
100
125
G007
VIN = 4.5 V
IOUT = 1 A
Figure 1. Voltage and Current vs Elapsed Time
Figure 2. Dropout Voltage vs Temperature
3.55
3.54
3.53
3.52
3.51
3.5
10.6
10.58
10.56
10.54
10.52
10.5
3.49
3.48
3.47
3.46
3.45
10.48
10.46
10.44
10.42
10.4
0
0.1 0.2 0.3 0.4 0.5 0.6 0.7 0.8 0.9
Charge Current (A)
1
0
25
50
75
100
125
Temperature (°C)
G008
G009
Figure 3. Battery Regulation Voltage vs Charge Current
Figure 4. OVP Threshold vs Temperature
1.1
1.05
1
0.95
0.9
0.85
0.8
0.75
0.7
0.65
0.6
0.55
0.5
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
100mA Current Limit
500mA Current Limit
Thermal
Regulation
0.45
0.4
5
6
7
8
9
10
2.5
2.75
3
Battery Voltage (V)
3.25
3.5
Input Voltage (V)
G010
G011
VIN = 5 V
Figure 5. Charge Current vs Input Voltage
Figure 6. Input Current Limit vs Battery Voltage
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
9 Detailed Description
9.1 Overview
The bq25071 is a highly integrated, linear, LiFePO4 battery charger targeted at space-limited portable
applications. It accepts power from either a USB port or AC adapter and charges a single-cell LiFePO4 battery
with up to 1 A of charge current. The 30 V input rating with 10.5 V input overvoltage protection supports low-cost
unregulated adapters.
The bq25071 has a single power output that simultaneously charges the battery and powers the system. The
input current is programmable from 100 mA up to 1 A using the ISET input or configurable for USB500. There is
also a 4.9 V ±10% 50 mA LDO is integrated into the IC for supplying low power external circuitry.
The LiFePO4 charging algorithm removes the constant voltage mode control typically used in Li-Ion battery
charge cycles which reduces charge time significantly. Instead, the battery is fast charged to the overcharge
voltage and then allowed to relax to a lower float charge voltage threshold. The charger power stage and charge
current sense functions are fully integrated. The charger function has high accuracy current and voltage
regulation loops, and charge status display. During the charge cycle, an internal control loop monitors the IC
junction temperature and reduces the charge current if an internal temperature threshold is exceeded.
8
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
9.2 Functional Block Diagram
LDO
+
Q2
Q1
OUT
BAT
IN
+
TJ(REG)
TJ
Charge Pump
IIN(REG)
+
1.5V
+
VBAT(REG)
ISET
VIN(SLP)
ILIM
+
+
VIN
VBAT
VUVLO
VIN
UVLO Comparator
Sleep Comparator
+
+
VOVP
VIN
VBAT
VBAT(REG)
Overcharge Comparator
OVP Comparator
EN
TS
Charge Control
CHG
Status Output
VLDO
TS Cold
+
Disable
+
TS Hot
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
9.3 Feature Description
9.3.1 Input Overvoltage Protection
The bq25071 contains an input overvoltage protection circuit that disables the LDO output and charging when
the input voltage rises above V(OVP). This prevents damage from faulty adapters. The OVP circuitry contains an
100 μs blanking period that prevents ringing on the input from line transients from tripping the OVP circuitry
falsely. If an adapter with an output greater than V(OVP) is plugged in, the IC completes soft-start power up and
then shuts down if the voltage remains above V(OVP) after 100 μs. The LDO remains off and charging remains
disabled until the input voltage falls below V(OVP)
.
9.3.2 Undervoltage Lockout (UVLO)
The bq25071 remains in power down mode when the input voltage is below the undervoltage lockout threshold
(V(UVLO)). During this mode, the control input (EN) is ignored. The LDO, the charge FET connected between IN
and OUT are off and the status output (CHG) is high impedance. Once the input voltage rises above V(UVLO), the
internal circuitry is turned on and the normal operating procedures are followed.
9.3.3 External NTC Monitoring (TS)
The bq25071 features a flexible, voltage based external battery pack temperature monitoring input. The TS input
connects to the NTC thermistor in the battery pack to monitor battery temperature and prevent dangerous over-
temperature conditions. During charging, the voltage at TS is continuously monitored. If the voltage at the TS pin
is outside of the operating range (V(HOT) to V(COLD) for longer than the built in 25 ms deglitch time, charging is
suspended. When the voltage measured at TS returns to within the operation window, charging resumes. When
a battery pack temperature fault occurs charging is suspended, but the CHG output remains low and continues to
indicate charging.
The temperature thresholds are programmed using a resistor divider from LDO to GND with the NTC thermistor
connected to the center tap from TS to GND. See Figure 7 for the circuit example. The value of R1 and R2 are
calculated using the following equations:
-R2 ´ RHOT ´ (0.125 - 1)
R1 =
0.125 ´ (R2 + RHOT)
(1)
-RHOT ´ RCOLD ´ (0.125 - 0.250)
R2 =
RHOT ´ 0.250 ´ (0.125 - 1) + RCOLD ´ 0.125 ´ (1 - 0.250)
(2)
RHOT is the expected thermistor resistance at the programmed hot threshold; RCOLD is the expected thermistor
resistance at the programmed cold threshold.
10
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
Feature Description (continued)
LDO
R1
VCOLD
PACK+
TS
TEMP
+
PACK-
VHOT
R2
+
bq25071
For applications that do not require the TS monitoring function, set R1 = 490 kΩ and R2 = 100 kΩ to set the TS
voltage at a valid level and maintain charging.
Figure 7. NTC Monitoring Function
9.3.4 50 mA LDO (LDO)
The LDO output of the bq25071 is a low dropout linear regulator (LDO) that supplies up to 50 mA while
regulating to V(LDO). The LDO is active whenever the input voltage is above V(UVLO) and below V(OVP). It is not
affected by the EN input. The LDO output is used to power and protect circuitry such as USB transceivers from
transients on the input supply.
9.3.5 Charge Status Indicator (CHG)
The bq25071 contains an open drain CHG output that indicates charging state and faults. When charging a
battery in precharge or fastcharge mode, the CHG output is pulled to GND. Once the BAT output reaches the
overcharge voltage threshold, CHG goes high impedance to signal the battery is fully charged. When the battery
voltage drops below the recharge voltage threshold the CHG output is pulled low to signal the host of a new
charge cycle. Connect CHG to the required logic level voltage through a 1 kΩ to 100 kΩ resistor to use the signal
with a microprocessor. I(CHG) must be below 5 mA.
The IC monitors the CHG pin when no input is connected to verify if the system circuitry is active. If the voltage
at CHG is logic being drive low when no input is connected, the TS circuit is turned off for a low quiescent current
state. Once the voltage at CHG increases above logic high, the TS circuit is turned on.
9.3.6 Input Current Limit Control (EN)
The bq25071 contains a 3-state that controls the input current limit. Drive EN low to program the input current
limit to the user defined value programmed using ISET. Drive EN high to place the bq25071 in USB suspend
mode. In USB suspend mode, the input current into bq25071 is reduced. Leaving EN unconnected or connected
to a high impedance source programs the USB500 input current limit.
Table 1. EN Input Definition
EN
Low
Hi-Z
Hi
MODE
ISET
USB500
USB Suspend
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
9.4 Device Functional Modes
9.4.1 Charging Operation
The bq25071 uses a charge algorithm that is unique to LiFePO4 chemistry cells. The current taper typically seen
as part of the constant voltage mode control usually present in Li-Ion battery charge cycles is replaced with a
floating regulation voltage with minimal charging current. This dramatically decreases the charge time. When the
bq25071 is enabled by EN, the battery voltage is monitored to verify which stage of charging must be used.
When V(BAT) < V(LOWV), the bq25071 charges in precharge mode; when V(BAT) > V(LOWV), the normal charge cycle
is used.
9.4.1.1 Charger Operation with Minimum System Voltage Mode Enabled
Constant Current
Fast Charge
Float-Voltage
Regulation
PRECHARGE
VOUT(OVCH)
VOUT(REG)
IFASTCHG
CHG = Hi-Z
Battery and
Output
Voltage
VLOWV
Battery
Current
IPRECHG
Figure 8. Typical Charging Cycle with Minimum System Voltage Enabled
9.4.1.2 Precharge Mode (V(BAT) ≤ V(LOWV)
)
The bq25071 enters precharge mode when VBAT ≤ V(LOWV). Upon entering precharge mode, the battery is
charged with a 47.5 mA current and CHG goes low.
9.4.1.3 Fast Charge Mode
Once V(BAT) > V(LOWV), the bq25071 enters constant current (CC) mode where charge current is regulated using
the internal MOSFETs between IN and OUT. The total current is shared between the output load and the battery.
Once the battery voltage charges up to VBAT(OVCH), the CHG output goes high indicating the charge cycle is
complete and the bq25071 switches the battery regulation voltage to VBAT(REG). The battery voltage is allowed to
relax down to VBAT(REG). The charger remains enabled and regulates the output to VBAT(REG). If at any time the
battery falls below V(RCH), the charge cycle restarts.
12
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
Device Functional Modes (continued)
9.4.2 Programmable Input Current Limit (ISET)
When the charger is enabled, and the user programmable current limit is selected by the EN input, internal
circuits generate a current proportional to the input current at the ISET input. The current out of ISET is 1/1000
(±10%) of the charge current. This current, when applied to the external charge current programming resistor, R1
(Figure 9), generates an analog voltage that is regulated to program the fast charge current. Connect a resistor
from ISET to GND to program the input current limit using the following equation:
K(ISET)
1000A ´W
I(IN_LIM)
=
=
R(ISET)
R(ISET)
(3)
I(IN_LIM) is programmable from 100 mA to 1 A. The voltage at ISET can be monitored by an external host to
calculate the charging current to the battery. The input current is related to the ISET voltage using the following
equation:
1000
´
I
= V
IN
(ISET)
R(ISET)
(4)
Monitoring the ISET voltage allows for the host to calculate the actual charging current and therefore perform
more accurate termination. The input current to the system must be monitored and subtracted from the current
into the bq25071 which is show by V(ISET)
.
9.4.3 Thermal Regulation and Thermal Shutdown
The bq25071 contains a thermal regulation loop that monitors the die temperature continuously. If the
temperature exceeds TJ(REG), the device automatically reduces the charging current to prevent the die
temperature from increasing further. In some cases, the die temperature continues to rise despite the operation
of the thermal loop, particularly under high VIN conditions. If the die temperature increases to TJ(OFF), the IC is
turned off. Once the device die temperature cools by TJ(OFF-HYS), the device turns on and returns to thermal
regulation. Continuous overtemperature conditions result in the pulsing of the load current. If the junction
temperature of the device exceeds TJ(OFF), the charge FET is turned off. The FET is turned back on when the
junction temperature falls below TJ(OFF) – TJ(OFF-HYS)
.
Note that these features monitor the die temperature of the bq25071. This is not synonymous with ambient
temperature. Self heating exists due to the power dissipated in the IC because of the linear nature of the battery
charging algorithm.
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
10 Application and Implementation
10.1 Application Information
The typical application circuit uses a single output which charges the battery and powers the system. Additionally
a 50-mA LDO can supply a low power external circuit.
The bq25071EVM-658 evaluation module (EVM) is a complete charger module for evaluating the bq25071. Refer
to SLUUB49.
10.2 Typical Application
V
GPIO
R2
100 kW
bq25071
STATUS
VDD
USB or TA
CHG
OUT
VBUS
GND
D+
IN
C1
0.1 mF
C2
1 mF
D-
ABB
EN
BAT
TS
PACK+
TEMP
ISET
GND
R1
1 kW
PACK-
VCHG DET
USB DET
LDO
PWRPD
C2
0.1 mF
R5
1.5 kW
R3
1.5 kW
VUSBIN
ACDET
R4
1.5 kW
GPIO
Figure 9. bq25071 Typical Application Circuit
Table 2. Design Parameters
10.2.1 Design Requirements
PARAMETER
EXAMPLE VALUE
5 V ±5%
Input supply range
Output voltage range
Output current rating
3.5 V
1000 mA
14
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
10.2.2 Detailed Design Procedure
10.2.2.1 Selection of Input and Output Capacitors
In most applications, all that is needed is a high-frequency decoupling capacitor on the input power pin. For
normal charging applications, a 0.1 μF ceramic capacitor, placed in close proximity to the IN pin and GND pad
works best. In some applications, depending on the power supply characteristics and cable length, it may be
necessary to increase the input filter capacitor to avoid exceeding the OVP voltage threshold during adapter hot
plug events where the ringing exceeds the deglitch time.
The charger in the bq25071 requires a capacitor from OUT to GND for loop stability. Connect a 1 μF ceramic
capacitor from OUT to GND close to the pins for best results. More output capacitance may be required to
minimize the output drop during large load transients.
The LDO also requires an output capacitor for loop stability. Connect a 0.1 μF ceramic capacitor from LDO to
GND close to the pins. For improved transient response, this capacitor may be increased.
10.2.2.2 Thermal Considerations
The bq25071 is packaged in a thermally enhanced QFN package. The package includes a thermal pad to
provide an effective thermal contact between the IC and the printed circuit board (PCB). Full PCB design
guidelines for this package are provided in the application note entitled: QFN/SON PCB Attachment Application
Note (SLUA271).
The most common measure of package thermal performance is thermal impedance (θJA) measured (or modeled)
from the chip junction to the air surrounding the package surface (ambient). The mathematical expression for θJA
is:
Where:
T
- T
A
J
q
=
JA
P
D
(5)
TJ = chip junction temperature
TA = ambient temperature
PD = device power dissipation
Factors that can greatly influence the measurement and calculation of θJA include:
•
•
•
•
•
Whether or not the device is board mounted
Trace size, composition, thickness, and geometry
Orientation of the device (horizontal or vertical)
Volume of the ambient air surrounding the device under test and airflow
Whether other surfaces are in close proximity to the device being tested
The device power dissipation, PD, is a function of the charge rate and the voltage drop across the internal
PowerFET. It can be calculated from the following equation when a battery pack is being charged:
PD = (VIN – VOUT) × IOUT
Due to the charge profile of LiFePO4 batteries the maximum power dissipation is typically seen at the beginning
of the charge cycle when the battery voltage is at its lowest. See the charging profile, Figure 8. If the board
thermal design is not adequate the programmed fast charge rate current may not be achieved under maximum
input voltage and minimum battery voltage, as the thermal loop can be active, effectively reducing the charge
current to avoid excessive IC junction temperature.
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
10.2.3 Application Curves
5V/div
V(CTRL)
V(LDO)
IOUT
5V/div
5V/div
VIN
5V/div
V(LDO)
200mA/div
200mA/div
2V/div
IOUT
2V/div
V(CHG)
V(CHG)
10ms/div
20ms/div
V(CTRL) = 0 V
Figure 11. Charger Enable Using EN
Figure 10. Adapter Plug-In With Battery Connected
5V/div
5V/div
V(CTRL)
5V/div
5V/div
V(LDO)
VIN
V(LDO)
200mA/div
IOUT
1A/div
2V/div
IOUT
2V/div
V(CHG)
V(CHG)
400μs/div
40μs/div
VIN = 5 V to 12 V
Figure 12. Charger Disable Using EN
Figure 13. OVP Fault
16
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
11 Power Supply Recommendations
In a typical application, the system is powered by a USB port or USB wall adapter.
The wide input voltage range supports low cost and unregulated adapters.
The minimum input voltage - where the charging process starts with a reduced charging current - could be 3.75
V. The maximum supported input voltage is up to 10 V; the overvoltage protection kicks in at 10.5 V and the
maximum input voltage rating is 30 V Input Rating.
12 Layout
12.1 Layout Guidelines
It is important to pay special attention to the PCB layout. The following provides some guidelines:
•
To obtain optimal performance, the decoupling capacitor from IN to GND (thermal pad) and the output filter
capacitors from OUT to GND (thermal pad) should be placed as close as possible to the bq25071, with short
trace runs to both IN, OUT and GND (thermal pad).
•
All low-current GND connections should be kept separate from the high-current charge or discharge paths
from the battery. Use a single-point ground technique incorporating both the small signal ground path and the
power ground path.
•
•
The high current charge paths into IN pin and from the OUT pin must be sized appropriately for the maximum
charge current in order to avoid voltage drops in these traces.
The bq25071 is packaged in a thermally enhanced SON package. The package includes a thermal pad to
provide an effective thermal contact between the IC and the printed circuit board (PCB); this thermal pad is
also the main ground connection for the device. Connect the thermal pad to the PCB ground connection. Full
PCB design guidelines for this package are provided in the application note entitled: QFN/SON PCB
Attachment Application Note (SLUA271).
12.2 Layout Example
The bottom plane is a ground plane that is connected to the top through vias.
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: bq25071
bq25071
SLUSBK6 –JULY 2014
www.ti.com
Layout Example (continued)
R1
D1
0.1mF
USB or Adapter
CHG
OUT
VBUS
GND
IN
C4
C3
1 mF
C2
C2
1 mF
D+
D-
0.1mF
22 mF
bq25071
U1
EN
BAT
TS
PACK+
TEMP
R3
R4
11.3kW
24.3kW
ISET
GND
R2
1 kW
PACK-
LDO
PWRPD
C5
0.1mF
Figure 14. Schematic
18
Submit Documentation Feedback
Copyright © 2014, Texas Instruments Incorporated
Product Folder Links: bq25071
bq25071
www.ti.com
SLUSBK6 –JULY 2014
13 Device and Documentation Support
13.1 Trademarks
All trademarks are the property of their respective owners.
13.2 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
13.3 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2014, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: bq25071
PACKAGE OPTION ADDENDUM
www.ti.com
31-Jul-2014
PACKAGING INFORMATION
Orderable Device
BQ25071DQCR
BQ25071DQCT
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
WSON
WSON
DQC
10
10
3000
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
25071
25071
ACTIVE
DQC
250
Green (RoHS
& no Sb/Br)
CU NIPDAU
Level-2-260C-1 YEAR
-40 to 85
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
31-Jul-2014
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Aug-2014
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
BQ25071DQCR
BQ25071DQCT
WSON
WSON
DQC
DQC
10
10
3000
250
180.0
180.0
8.4
8.4
2.25
2.25
3.25
3.25
1.05
1.05
4.0
4.0
8.0
8.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
18-Aug-2014
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
BQ25071DQCR
BQ25071DQCT
WSON
WSON
DQC
DQC
10
10
3000
250
210.0
210.0
185.0
185.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
相关型号:
BQ25100A_15
bq2510x 250-mA Single Cell Li-Ion Battery Chargers, 1-mA Termination, 75-nA Battery Leakage
TI
©2020 ICPDF网 联系我们和版权申明