CSD87334Q3D [TI]
CSD87334Q3D Synchronous Buck NexFET Power Block;型号: | CSD87334Q3D |
厂家: | TEXAS INSTRUMENTS |
描述: | CSD87334Q3D Synchronous Buck NexFET Power Block 开关 光电二极管 |
文件: | 总22页 (文件大小:1172K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Sample &
Buy
Support &
Community
Product
Folder
Tools &
Software
Technical
Documents
CSD87334Q3D
SLPS546 –JULY 2015
CSD87334Q3D Synchronous Buck NexFET™ Power Block
1 Features
3 Description
The CSD87334Q3D NexFET™ power block is an
optimized design for synchronous buck and boost
applications offering high current, high efficiency, and
high frequency capability in a small 3.3 mm × 3.3 mm
outline. Optimized for 5-V gate drive applications, this
product offers a flexible solution in high duty cycle
applications when paired with an external controller or
driver.
1
•
•
•
•
•
•
•
•
•
•
•
•
•
•
Half-Bridge Power Block
Optimized for High Duty Cycle
Up to 24 Vin
96.1% System Efficiency at 12 A
1.6 W PLoss at 12 A
Up to 20 A operation
High-Frequency Operation (Up to 1.5 MHz)
High Density – SON 3.3 mm × 3.3 mm Footprint
Optimized for 5-V Gate Drive
Low Switching Losses
TEXT ADDED FOR SPACING
Top View
VIN
VIN
TG
VSW
VSW
VSW
1
2
3
4
8
7
6
5
Ultra-Low Inductance Package
RoHS Compliant
PGND
(Pin 9)
Halogen-Free
Pb-Free Terminal Plating
TGR
BG
P0116-01
2 Applications
•
Synchronous Buck Converters
TEXT ADDED FOR SPACING
Device Information(1)
–
–
High Frequency Applications
High Duty Cycle Applications
DEVICE
QTY
2500 13-Inch Reel
250 7-Inch Reel
MEDIA
PACKAGE
SHIP
CSD87334Q3D
SON
3.3 mm × 3.3 mm
Plastic Package
•
•
Synchronous Boost Converters
POL DC-DC Converters
Tape and
Reel
CSD87334Q3DT
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
SPACER
SPACER
Typical Circuit
Typical Power Block Efficiency and Power Loss
100
90
80
70
60
50
5
4
3
2
1
0
VIN
BOOT
VDD
VDD
GND
VIN
TG
DRVH
LL
VGS = 5 V
VIN = 12 V
VOUT = 3.3 V
TGR
VSW
VOUT
ENABLE
PWM
ENABLE
PWM
LOUT = 1.0
SW = 500 kHz
TA = 25
PH
BG
DRVL
f
PGND
qC
CSD87334Q3D
Driver IC
0
5
10
15
20
Output Current (A)
D000
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
Table of Contents
6.3 System Example ....................................................... 9
Layout ................................................................... 12
7.1 Layout Guidelines ................................................... 12
7.2 Layout Example ...................................................... 13
7.3 Thermal Considerations.......................................... 13
Device and Documentation Support.................. 14
8.1 Community Resources............................................ 14
8.2 Trademarks............................................................. 14
8.3 Electrostatic Discharge Caution.............................. 14
8.4 Glossary.................................................................. 14
1
2
3
4
5
Features.................................................................. 1
7
Applications ........................................................... 1
Description ............................................................. 1
Revision History..................................................... 2
Specifications......................................................... 3
5.1 Absolute Maximum Ratings ...................................... 3
5.2 Recommended Operating Conditions....................... 3
5.3 Power Block Performance ........................................ 3
5.4 Thermal Information.................................................. 3
5.5 Electrical Characteristics........................................... 4
5.6 Typical Power Block Device Characteristics............. 5
5.7 Typical Power Block MOSFET Characteristics......... 7
Application and Implementation .......................... 9
6.1 Application Information.............................................. 9
6.2 Typical Application .................................................... 9
8
9
Mechanical, Packaging, and Orderable
Information ........................................................... 15
9.1 Q3D Package Dimensions...................................... 15
9.2 Land Pattern Recommendation .............................. 16
9.3 Stencil Recommendation ........................................ 17
9.4 Q3D Tape and Reel Information............................. 17
6
4 Revision History
DATE
REVISION
NOTES
July 2015
*
Initial release.
2
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
5 Specifications
5.1 Absolute Maximum Ratings
(1)
TA = 25°C (unless otherwise noted) (see
)
MIN
MAX
UNIT
V
VIN to PGND
30
30
32
10
10
60
6
VSW to PGND
VSW to PGND (10 ns)
TG to TGR
V
Voltage
V
–8
–8
V
BG to PGND
V
IDM
PD
Pulsed current rating
Power dissipation
A
W
Sync FET, ID = 31 A, L = 0.1 mH
Control FET, ID = 31 A, L = 0.1 mH
48
48
150
150
EAS
Avalanche energy
mJ
TJ
Operating junction temperature
Storage temperature
–55
–55
°C
°C
Tstg
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability
5.2 Recommended Operating Conditions
TA = 25° (unless otherwise noted)
MIN
MAX
8
UNIT
V
VGS
VIN
Gate drive voltage
Input supply voltage
Switching frequency
Operating current
3.3
24
V
ƒSW
CBST = 0.1 µF (min)
1500
20
kHz
A
TJ
Operating temperature
125
°C
5.3 Power Block Performance
(1)
TA = 25° (unless otherwise noted) (see
)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
VIN = 12 V, VGS = 5 V, VOUT = 3.3 V,
IOUT = 12 A, ƒSW = 500 kHz,
LOUT = 1 µH, TJ = 25ºC
PLOSS
IQVIN
Power loss(1)
1.6
W
VIN quiescent current
TG to TGR = 0 V BG to PGND = 0 V
10
µA
(1) Measurement made with six 10-µF (TDK C3216X5R1C106KT or equivalent) ceramic capacitors placed across VIN to PGND pins and
using a high current 5-V driver IC.
5.4 Thermal Information
TA = 25°C (unless otherwise stated)
THERMAL METRIC
Junction-to-ambient thermal resistance (min Cu)(1)
Junction-to-ambient thermal resistance (max Cu)(1)(2)
Junction-to-case thermal resistance (top of package)(1)
Junction-to-case thermal resistance (PGND pin)(1)
MIN
TYP
MAX UNIT
130
°C/W
75
RθJA
21
RθJC
(1)
°C/W
2.1
R
θJC is determined with the device mounted on a 1-inch2 (6.45 cm2), 2-oz. (0.071 mm thick) Cu pad on a 1.5 inch × 1.5 inch
(3.81 cm × 3.81 cm), 0.06-inch (1.52 mm) thick FR4 board. RθJC is specified by design while RθJA is determined by the user’s board
design.
(2) Device mounted on FR4 material with 1-inch2 (6.45 cm2) Cu.
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
5.5 Electrical Characteristics
TA = 25°C (unless otherwise stated)
Q1 CONTROL FET
Q2 SYNC FET
PARAMETER
TEST CONDITIONS
UNIT
MIN
TYP
MAX
MIN
TYP
MAX
STATIC CHARACTERISTICS
BVDSS
Drain-to-source voltage
VGS = 0 V, IDS = 250 µA
VGS = 0 V, VDS = 20 V
30
30
V
Drain-to-source leakage
current
IDSS
1
100
1
100
µA
Gate-to-source leakage
current
IGSS
VDS = 0 V, VGS = +10 / –8 V
nA
V
Gate-to-source threshold
voltage
VGS(th)
VDS = VGS, IDS = 250 µA
VGS = 3.5 V, IDS = 12 A
0.75
0.90
1.20
0.75
0.90
1.20
6.3
5.6
4.9
62
8.3
7.0
6.0
6.3
5.6
4.9
62
8.3
7.0
6.0
RDS(on)
Drain-to-source on resistance VGS = 4.5 V, IDS = 12 A
VGS = 8 V, IDS = 12 A
mΩ
gfs
Transconductance
VDS = 15 V, IDS = 12 A
S
DYNAMIC CHARACTERISTICS
CISS
COSS
CRSS
RG
Input capacitance
971
453
16
1260
589
21
971
453
16
1260
589
21
pF
pF
pF
Ω
VGS = 0 V, VDS = 15 V,
ƒ = 1 MHz
Output capacitance
Reverse transfer capacitance
Series gate resistance
Gate charge total (4.5 V)
Gate charge – gate to drain
Gate charge – gate to source
Gate charge at Vth
Output charge
1.0
6.4
1.0
1.9
0.9
10.5
4
2.0
1.0
6.4
1.0
1.9
0.9
10.5
4
2.0
Qg
8.3
8.3
nC
nC
nC
nC
nC
ns
ns
ns
ns
Qgd
Qgs
Qg(th)
QOSS
td(on)
tr
VDS = 15 V,
IDS = 12 A
VDS = 15 V, VGS = 0 V
Turn on delay time
Rise time
7
7
VDS = 15 V, VGS = 4.5 V,
IDS = 12 A, RG = 2 Ω
td(off)
tf
Turn off delay time
Fall time
11
11
17
17
DIODE CHARACTERISTICS
VSD
Qrr
trr
Diode forward voltage
Reverse recovery charge
Reverse Recovery Time
IDS = 12 A, VGS = 0 V
0.8
23
18
1.0
0.8
23
18
1.0
V
nC
ns
VDS = 15 V, IF = 12 A,
di/dt = 300 A/µs
Max RθJA = 75°C/W
when mounted on
1 inch2 (6.45 cm2) of 2
oz. (0.071 mm thick)
Cu.
Max RθJA = 130°C/W
when mounted on
minimum pad area of 2
oz. (0.071 mm thick)
Cu.
4
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
5.6 Typical Power Block Device Characteristics
The Typical Power Block System Characteristic curves (Figure 1 through Figure 9) are based on measurements made on a
PCB design with dimensions of 4.0 inch (W) × 3.5 inch (L) × 0.062 inch (H) and 6 copper layers of 1-oz. copper thickness.
See Application and Implementation for detailed explanation. xxConditions for Figure 1 through Figure 5 are given by the
following; VIN = 12 V, VGS = 5 V, VOUT = 3.3 V, ƒSW = 500 kHz, LOUT = 1.0 µH. xxTA = 125°C, unless stated otherwise.
6
5
4
3
2
1
0
1.05
1
0.95
0.9
0.85
0.8
0.75
0.7
0.65
0
4
8
12
16
20
-50
-25
0
25
50
75
100
125
150
Output Current (A)
Junction Temperature (qC)
D001
D002
Figure 1. Power Loss vs Output Current
Figure 2. Power Loss vs Temperature
25
20
15
10
5
25
20
15
10
5
400 LFM
200 LFM
100 LFM
Nat. conv.
400 LFM
200 LFM
100 LFM
Nat. conv.
0
0
0
10
20
30
40
50
60
70
80
90
0
10
20
30
40
50
60
70
80
90
Ambient Temperature (qC)
Ambient Temperature (qC)
D003
D004
Figure 3. Safe Operating Area – PCB Horizontal Mount
Figure 4. Safe Operating Area – PCB Vertical Mount
25
20
15
10
5
0
0
20
40
60
80
100
120
140
Board Temperature (qC)
D005
Figure 5. Typical Safe Operating Area
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
Typical Power Block Device Characteristics (continued)
The Typical Power Block System Characteristic curves (Figure 1 through Figure 9) are based on measurements made on a
PCB design with dimensions of 4.0 inch (W) × 3.5 inch (L) × 0.062 inch (H) and 6 copper layers of 1-oz. copper thickness.
See Application and Implementation for detailed explanation. xxConditions for Figure 1 through Figure 5 are given by the
following; VIN = 12 V, VGS = 5 V, VOUT = 3.3 V, ƒSW = 500 kHz, LOUT = 1.0 µH. xxTA = 125°C, unless stated otherwise.
1.2
1.15
1.1
1.8
1.3
0.9
0.4
0.0
-0.4
1.2
1.15
1.1
1.8
1.3
0.9
0.4
0.0
-0.4
-0.9
-1.3
1.05
1
1.05
1
0.95
0.9
0.95
0.85
100
300
500
700
900 1100 1300 1500 1700
0
4
8
12
16
20
24
28
Switching Frequency (kHz)
Input Voltage (V)
D006
D007
VIN = 12 V
IOUT = 15 A
VGS = 5 V
VOUT = 3.3 V
ƒSW = 500 kHz
IOUT = 15 A
VGS = 5 V
VOUT = 3.3 V
LOUT = 1.0 µH
LOUT = 1.0 µH
Figure 6. Normalized Power Loss vs Switching Frequency
Figure 7. Normalized Power Loss vs Input Voltage
1.15
1.4
1.2
1.15
1.1
1.8
1.1
1.05
1
0.9
1.4
0.5
0.9
0.0
1.05
1
0.5
0.95
0.9
-0.5
-0.9
-1.4
-1.8
0.0
0.95
0.9
-0.5
-0.9
-1.4
0.85
0.8
0.85
0.5
1
1.5
2
2.5
3
3.5
4
4.5
5
5.5
6
6.5
7
100
400
700 1000 1300 1600 1900 2200 2500
Output Voltage (V)
Output Inductance (nH)
D008
D009
VIN = 12 V
VGS = 5 V
IOUT = 15 A
VIN = 12 V
VGS = 5 V
IOUT = 15 A
ƒSW = 500 kHz
LOUT = 1.0 µH
ƒSW = 500 kHz
VOUT = 3.3 V
Figure 8. Normalized Power Loss vs Output Voltage
Figure 9. Normalized Power Loss vs Output Inductance
6
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
5.7 Typical Power Block MOSFET Characteristics
TA = 25°C, unless stated otherwise.
100
90
80
70
60
50
40
30
100
10
TC = 125°C
TC = 25°C
TC = -55°C
1
0.1
20
0.01
0.001
VGS = 3.5 V
VGS = 4.5 V
VGS = 8.0 V
10
0
0
0.1
0.2
0.3
0.4
0.5
0.6
0.7
0.8
0.9
0
0.5
1
1.5
2
2.5
3
VDS - Drain-to-Source Voltage (V)
VGS - Gate-to-Source Voltage (V)
D011
D010
VDS = 5 V
Figure 11. MOSFET Transfer Characteristics
Figure 10. MOSFET Saturation Characteristics
5000
1000
8
7
6
5
4
3
2
1
0
100
10
1
Ciss = Cgd + Cgs
Coss = Cds + Cgd
Crss = Cgd
0
2
4
6
8
10
12
0
3
6
9
12
15
18
21
24
27
30
Qg - Gate Charge (nC)
VDS - Drain-to-Source Voltage (V)
D012
D013
ID = 12 A
VDS = 15 V
Figure 12. MOSFET Gate Charge
Figure 13. MOSFET Capacitance
16
14
12
10
8
1.3
1.2
1.1
1
TC = 25°C, I D = 12 A
TC = 125°C, I D = 12 A
0.9
0.8
0.7
0.6
0.5
0.4
0.3
6
4
2
0
-75 -50 -25
0
25
50
75 100 125 150 175
0
1
2
3
4
5
6
7
8
9
10
TC - Case Temperature (°C)
VGS - Gate-to-Source Voltage (V)
D014
D014
ID = 250 µA
Figure 14. MOSFET VGS(th)
Figure 15. MOSFET RDS(on) vs VGS
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
Typical Power Block MOSFET Characteristics (continued)
TA = 25°C, unless stated otherwise.
100
10
1.6
1.4
1.2
1
TC = 25°C
TC = 125°C
1
0.1
0.01
0.001
0.0001
0.8
0.6
-75 -50 -25
0
25
50
75 100 125 150 175
0
0.2
0.4
0.6
0.8
1
TC - Case Temperature (°C)
VSD - Source-to-Drain Voltage (V)
D016
D017
ID = 12 A
Figure 16. MOSFET Normalized RDS(on)
Figure 17. MOSFET Body Diode
100
TC = 25q C
TC = 125q C
10
1
0.01
0.1
TAV - Time in Avalanche (ms)
1
D018
Figure 18. MOSFET Unclamped Inductive Switching
8
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
6 Application and Implementation
NOTE
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
6.1 Application Information
The CSD87334Q3D NexFET power block is an optimized design for synchronous buck applications using 5-V
gate drive. The Control FET and Sync FET silicon are parametrically tuned to yield the lowest power loss and
highest system efficiency. As a result, a new rating method is needed which is tailored towards a more systems
centric environment. System level performance curves such as Power Loss, Safe Operating Area, and
normalized graphs allow engineers to predict the product performance in the actual application.
6.2 Typical Application
Input Current (IIN)
VIN
A
BOOT
DRVH
LL
VDD
A
VDD
V
VIN
Input Voltage (VIN)
Gate Drive
Voltage (VDD)
V
TG
ENABLE
PWM
Output Current (IOUT
)
TGR
VSW
A
VOUT
PWM
BG
DRVL
PGND
GND
Averaged Switch
V Node Voltage
Averaging
Circuit
CSD87334Q3D
Driver IC
(VSW_AVG
)
Figure 19. Typical Circuit Application
6.3 System Example
6.3.1 Power Loss Curves
MOSFET centric parameters such as RDS(ON) and Qgd are needed to estimate the loss generated by the devices.
In an effort to simplify the design process for engineers, Texas Instruments has provided measured power loss
performance curves. Figure 1 plots the power loss of the CSD87334Q3D as a function of load current. This curve
is measured by configuring and running the CSD87334Q3D as it would be in the final application (see
Figure 19). The measured power loss is the CSD87334Q3D loss and consists of both input conversion loss and
gate drive loss. Equation 1 is used to generate the power loss curve.
(VIN × IIN) + (VDD × IDD) – (VSW_AVG × IOUT) = Power Loss
(1)
The power loss curve in Figure 1 is measured at the maximum recommended junction temperatures of 125°C
under isothermal test conditions.
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
System Example (continued)
6.3.2 Safe Operating Curves (SOA)
The SOA curves in the CSD87334Q3D data sheet provides guidance on the temperature boundaries within an
operating system by incorporating the thermal resistance and system power loss. Figure 3 to Figure 5 outline the
temperature and airflow conditions required for a given load current. The area under the curve dictates the SOA.
All the curves are based on measurements made on a PCB design with dimensions of 4 inches (W) × 3.5 inches
(L) × 0.062 inches (T) and 6 copper layers of 1-oz. copper thickness.
6.3.3 Normalized Curves
The normalized curves in the CSD87334Q3D data sheet provides guidance on the Power Loss and SOA
adjustments based on their application specific needs. These curves show how the power loss and SOA
boundaries adjust for a given set of system conditions. The primary Y-axis is the normalized change in power
loss, and the secondary Y-axis is the change is system temperature required in order to comply with the SOA
curve. The change in power loss is a multiplier for the Power Loss curve and the change in temperature is
subtracted from the SOA curve.
6.3.4 Calculating Power Loss and SOA
The user can estimate product loss and SOA boundaries by arithmetic means (see Design Example). Though
the Power Loss and SOA curves in this data sheet are taken for a specific set of test conditions, the following
procedure outlines the steps the user should take to predict product performance for any set of system
conditions.
6.3.4.1 Design Example
Operating Conditions:
•
•
•
•
•
Output Current = 15 A
Input Voltage = 16 V
Output Voltage = 5 V
Switching Frequency = 1000 kHz
Inductor = 0.6 µH
6.3.4.2 Calculating Power Loss
•
•
•
•
•
•
Power Loss at 15 A = 2.8 W (Figure 1)
Normalized Power Loss for input voltage ≈ 1.05 (Figure 7)
Normalized Power Loss for output voltage ≈ 1.08 (Figure 8)
Normalized Power Loss for switching frequency ≈ 1.03 (Figure 6)
Normalized Power Loss for output inductor ≈ 1.05 (Figure 9)
Final calculated Power Loss = 2.8 W x 1.05 × 1.08 × 1.03 × 1.05 ≈ 3.4 W
6.3.4.3 Calculating SOA Adjustments
•
•
•
•
•
SOA adjustment for input voltage ≈ 0.5ºC (Figure 7)
SOA adjustment for output voltage ≈ 0.7ºC (Figure 8)
SOA adjustment for switching frequency ≈ 0.3ºC (Figure 6)
SOA adjustment for output inductor ≈ 0.5ºC (Figure 9)
Final calculated SOA adjustment = 0.5 + 0.7 + 0.3 + 0.5 ≈ 2.0ºC
In the design example, the estimated power loss of the CSD87334Q3D would increase to 3.4 W. In addition, the
maximum allowable board or ambient temperature, or both, would have to decrease by 2.0ºC. Figure 20
graphically shows how the SOA curve would be adjusted accordingly.
1. Start by drawing a horizontal line from the application current to the SOA curve.
2. Draw a vertical line from the SOA curve intercept down to the board or ambient temperature.
3. Adjust the SOA board or ambient temperature by subtracting the temperature adjustment value.
10
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
System Example (continued)
In the design example, the SOA temperature adjustment yields a reduction in allowable board/ambient
temperature of 2.0ºC. In the event the adjustment value is a negative number, subtracting the negative number
would yield an increase in allowable board or ambient temperature.
SPACE
Figure 20. Power Block SOA
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
7 Layout
7.1 Layout Guidelines
7.1.1 Recommended PCB Design Overview
There are two key system-level parameters that can be addressed with a proper PCB design: electrical and
thermal performance. Properly optimizing the PCB layout yields maximum performance in both areas. A brief
description on how to address each parameter is provided.
7.1.2 Electrical Performance
The Power Block has the ability to switch voltages at rates greater than 10 kV/µs. Special care must be then
taken with the PCB layout design and placement of the input capacitors, Driver IC, and output inductor.
•
The placement of the input capacitors relative to the Power Block’s VIN and PGND pins should have the
highest priority during the component placement routine. It is critical to minimize these node lengths. As such,
ceramic input capacitors need to be placed as close as possible to the VIN and PGND pins (see Figure 21).
The example in Figure 21 uses six 10=µF ceramic capacitors (TDK part number C3216X5R1C106KT or
equivalent). Notice there are ceramic capacitors on both sides of the board with an appropriate amount of
vias interconnecting both layers. In terms of priority of placement next to the Power Block, C5, C7, C19, and
C8 should follow in order.
•
•
The Driver IC should be placed relatively close to the Power Block Gate pins. TG and BG should connect to
the outputs of the Driver IC. The TGR pin serves as the return path of the high-side gate drive circuitry and
should be connected to the Phase pin of the IC (sometimes called LX, LL, SW, PH, and so forth). The
bootstrap capacitor for the Driver IC will also connect to this pin.
The switching node of the output inductor should be placed relatively close to the Power Block VSW pins.
Minimizing the node length between these two components will reduce the PCB conduction losses and
actually reduce the switching noise level.(1) In the event the switch node waveform exhibits ringing that
reaches undesirable levels, the use of a Boost Resistor or RC snubber can be an effective way to easily
reduce the peak ring level. The recommended Boost Resistor value will range between 1.0 to 4.7 Ω
depending on the output characteristics of Driver IC used in conjunction with the Power Block. The RC
snubber values can range from 0.5 to 2.2 Ω for the R, and from 330 to 2200 pF for the C. Please refer to
Snubber Circuits: Theory, Design and Application (SLUP100) for more details on how to properly tune the RC
snubber values. The RC snubber should be placed as close as possible to the VSW node and PGND (see
(1)
Figure 21).
(1) Keong W. Kam, David Pommerenke, “EMI Analysis Methods for Synchronous Buck Converter EMI Root Cause Analysis”, University of
Missouri – Rolla
12
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
7.2 Layout Example
Figure 21. Recommended PCB Layout (Top Down)
7.3 Thermal Considerations
The Power Block has the ability to utilize the GND planes as the primary thermal path. As such, the use of
thermal vias is an effective way to pull away heat from the device and into the system board. Concerns of solder
voids and manufacturability problems can be addressed by the use of three basic tactics to minimize the amount
of solder attach that will wick down the via barrel:
•
•
Intentionally space out the vias from each other to avoid a cluster of holes in a given area.
Use the smallest drill size allowed in your design. The example in Figure 21 uses vias with a 10-mil drill hole
and a 16-mil capture pad.
•
Tent the opposite side of the via with solder-mask.
The number and drill size of the thermal vias should align with the PCB design rules and manufacturing
capabilities of the end user.
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
8 Device and Documentation Support
8.1 Community Resources
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
8.2 Trademarks
NexFET, E2E are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
8.3 Electrostatic Discharge Caution
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
8.4 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
14
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
9 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
9.1 Q3D Package Dimensions
MILLIMETERS
NOM
INCHES
NOM
DIM
MIN
0.850
0.280
MAX
1.050
0.400
MIN
0.033
0.011
MAX
0.041
0.016
A
b
b1
c
0.310
0.012
0.150
0.150
0.940
0.160
0.150
0.250
0.175
3.200
2.650
3.200
3.200
1.750
0.250
0.250
1.040
0.260
0.250
0.350
0.275
3.400
2.750
3.400
3.400
1.850
0.006
0.006
0.037
0.006
0.006
0.010
0.007
0.126
0.104
0.126
0.126
0.069
0.010
0.010
0.041
0.010
0.010
0.014
0.011
0.134
0.108
0.134
0.134
0.073
c1
d
d1
d2
d3
d4
D1
D2
E
E1
E2
e
0.650 TYP
0.300 TYP
0.026 TYP
0.012 TYP
L
0.400
0.000
0.500
–
0.016
–
0.020
–
θ
K
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: CSD87334Q3D
CSD87334Q3D
SLPS546 –JULY 2015
www.ti.com
Pinout Configuration
POSITION
DESIGNATION
Pin 1
VIN
VIN
Pin 2
Pin 3
TG
Pin 4
TGR
BG
Pin 5
Pin 6
VSW
VSW
VSW
PGND
Pin 7
Pin 8
Pin 9
9.2 Land Pattern Recommendation
1.900 (0.075)
0.200
(0.008)
0.210
(0.008)
0.350 (0.014)
0.440
(0.017)
0.650
(0.026)
2.800
(0.110)
2.390
(0.094)
1.090
(0.043)
0.210
(0.008)
0.300 (0.012)
0.650 (0.026)
0.650 (0.026)
3.600 (0.142)
M0193-01
NOTE: Dimensions are in mm (inches).
16
Submit Documentation Feedback
Copyright © 2015, Texas Instruments Incorporated
Product Folder Links: CSD87334Q3D
CSD87334Q3D
www.ti.com
SLPS546 –JULY 2015
9.3 Stencil Recommendation
0.160 (0.005)
0.550 (0.022)
0.200 (0.008)
0.300 (0.012)
0.300
(0.012)
0.340
(0.013)
2.290
(0.090)
0.333
(0.013)
0.990
(0.039)
0.100
(0.004)
0.350 (0.014)
0.300 (0.012)
0.850 (0.033)
3.500 (0.138)
M0207-01
NOTE: Dimensions are in mm (inches).
For recommended circuit layout for PCB designs, see Reducing Ringing Through PCB Layout Techniques
(SLPA005).
9.4 Q3D Tape and Reel Information
4.00 0.ꢀ0 ꢁ(SS ꢂNoS ꢀ1
8.00 0.ꢀ0
2.00 0.0ꢃ
Ø ꢀ.ꢃ0
+0.ꢀ0
–0.00
3.60
M0ꢀ44-0ꢀ
NOTES: 1. 10-sprocket hole-pitch cumulative tolerance ± 0.2
2. Camber not to exceed 1 mm in 100 mm, noncumulative over 250 mm
3. Material: black static-dissipative polystyrene
4. All dimensions are in mm, unless otherwise specified.
5. Thickness: 0.30 ± 0.05 mm
6. MSL1 260°C (IR and convection) PbF reflow compatible
Copyright © 2015, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: CSD87334Q3D
PACKAGE OPTION ADDENDUM
www.ti.com
7-Aug-2015
PACKAGING INFORMATION
Orderable Device
CSD87334Q3D
CSD87334Q3DT
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-55 to 150
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
VSON
VSON
DPB
8
8
2500 Pb-Free (RoHS
Exempt)
CU NIPDAU
Level-1-260C-UNLIM
87334D
87334D
ACTIVE
DPB
250
Pb-Free (RoHS
Exempt)
CU NIPDAU
Level-1-260C-UNLIM
-55 to 150
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Aug-2015
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Aug-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
CSD87334Q3D
CSD87334Q3DT
VSON
VSON
DPB
DPB
8
8
2500
250
330.0
180.0
12.4
12.4
3.6
3.6
3.6
3.6
1.2
1.2
8.0
8.0
12.0
12.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Aug-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
CSD87334Q3D
CSD87334Q3DT
VSON
VSON
DPB
DPB
8
8
2500
250
367.0
210.0
367.0
185.0
35.0
35.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明