DS90CR212MTDX [TI]
QUAD LINE RECEIVER, PDSO48, PLASTIC, TSSOP-48;型号: | DS90CR212MTDX |
厂家: | TEXAS INSTRUMENTS |
描述: | QUAD LINE RECEIVER, PDSO48, PLASTIC, TSSOP-48 |
文件: | 总15页 (文件大小:301K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
DS90CR211,DS90CR212
DS90CR211/DS90CR212 21-Bit Channel Link
Literature Number: SNLS112A
July 1997
DS90CR211/DS90CR212
21-Bit Channel Link
needed. This provides a 80% reduction in required cable
width, providing a system cost savings, reduces connector
physical size, and reduces shielding requirements due to the
cables smaller form factor.
General Description
The DS90CR211 transmitter converts 21 bits of CMOS/TTL
data into three LVDS (Low Voltage Differential Signaling)
data streams. A phase-locked transmit clock is transmitted in
parallel with the data streams over a fourth LVDS link. Every
cycle of the transmit clock 21 bits of input data are sampled
and transmitted. The DS90CR212 receiver converts the
LVDS data streams back into 21 bits of CMOS/TTL data. At
a transmit clock frequency of 40 MHz, 21 bits of TTL data are
transmitted at a rate of 280 Mbps per LVDS data channel.
The 21 CMOS/TTL inputs can support a variety of signal
combinations. For example, 5 4-bit nibbles plus 1 control, or
2 9-bit (byte + parity) and 3 control.
Features
n Narrow bus reduces cable size and cost
Using
Mbit/s(105 Mbyte/s).
a 40 MHz clock, the data throughput is 840
±
n
1V Common mode range (ground shifting)
n 290 mV swing LVDS data transmission
n 840 Mbit/s data throughput
n Low swing differential current mode drivers reduce EMI
n Rising edge data strobe
n Power down mode
n Offered in low profile 48-lead TSSOP package
The multiplexing of the data lines provides a substantial
cable reduction. Long distance parallel single-ended buses
typically require a ground wire per active signal (and have
very limited noise rejection capability). Thus, for a 21-bit wide
data bus and one clock, up to 44 conductors are required.
With the Channel Link chipset as few as 9 conductors (3
data pairs, 1 clock pair and a minimum of one ground) are
Block Diagrams
DS90CR211
DS90CR212
DS012637-27
DS012637-1
Order Number DS90CR211MTD
See NS Package Number MTD48
Order Number DS90CR212MTD
See NS Package Number MTD48
TRI-STATE® is a registered trademark of National Semiconductor Corporation.
© 2000 National Semiconductor Corporation
DS012637
www.national.com
Connection Diagrams
DS90CR211
DS90CR212
DS012637-2
DS012637-3
Typical Application
DS012637-19
www.national.com
2
Absolute Maximum Ratings (Note 1)
If Military/Aerospace specified devices are required,
please contact the National Semiconductor Sales Office/
Distributors for availability and specifications.
MTD48 (TSSOP) Package:
DS90CR211
1.98W
1.89W
DS90CR212
Package Derating:
DS90CR211
16 mW/˚C above +25˚C
15 mW/˚C above +25˚C
Supply Voltage (VCC
)
−0.3V to +6V
−0.3V to (VCC + 0.3V)
−0.3V to (VCC + 0.3V)
−0.3V to (VCC + 0.3V)
−0.3V to (VCC + 0.3V)
DS90CR212
CMOS/TTL Input Voltage
CMOS/TTL Ouput Voltage
LVDS Receiver Input Voltage
LVDS Driver Output Voltage
LVDS Output
This device does not meet 2000V ESD rating (Note 4) .
Recommended Operating
Conditions
Short Circuit Duration
Junction Temperature
Storage Temperature Range
Lead Temperature
continuous
+150˚C
Min Max Units
Supply Voltage (VCC
)
4.5
−10 +70
2.4
5.5
V
˚C
V
−65˚C to +150˚C
Operating Free Air Temperature (TA)
Receiver Input Range
0
(Soldering, 4 sec.)
+260˚C
Supply Noise Voltage (VCC
)
100 mVPP
@
Maximum Power Dissipation +25˚C
Electrical Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol Parameter Conditions
CMOS/TTL DC SPECIFICATIONS
Min
Typ
Max
Units
VIH
VIL
High Level Input Voltage
Low Level Input Voltage
High Level Output Voltage
Low Level Output Voltage
Input Clamp Voltage
2.0
GND
3.8
VCC
0.8
V
V
VOH
VOL
VCL
IIN
IOH = −0.4 mA
IOL = 2 mA
4.9
0.1
V
0.3
V
ICL = −18 mA
−0.79
−1.5
V
±
±
10
Input Current
VIN = VCC, GND, 2.5V or 0.4V
VOUT = 0V
5.1
µA
IOS
Output Short Circuit Current
−120
mA
LVDS DRIVER DC SPEClFlCATIONS
VOD
Differential Output Voltage
Change in VOD between
RL = 100Ω
250
1.1
290
1.25
−2.9
450
35
mV
mV
∆VOD
Complementary Output States
Common Mode Voltage
VCM
1.375
35
V
∆VCM
Change in VCM between
mV
Complementary Output States
Output Short Circuit Current
Output TRI-STATE® Current
IOS
IOZ
VOUT = 0V, RL = 100Ω
−5
mA
µA
±
±
10
Power Down = 0V, VOUT = 0V or VCC
1
LVDS RECEIVER DC SPECIFlCATIONS
VTH
VTL
IIN
Differential Input High Threshold
Differential Input Low Threshold
Input Current
VCM = +1.2V
+100
mV
mV
µA
−100
<
<
±
±
±
±
VIN = +2.4V
VIN = 0V
VCC = 5.5V
1
1
10
10
µA
TRANSMITTER SUPPLY CURRENT
ICCTW
Transmitter Supply Current,
Worst Case
RL = 100Ω, CL = 5 pF,
Worst Case Pattern
(Figure 1, Figure 2)
f = 32.5 MHz
f = 37.5 MHz
34
51
mA
36
1
53
25
mA
µA
ICCTZ
Transmitter Supply Current,
Power Down
Power Down = Low
RECEIVER SUPPLY CURRENT
ICCRW
Receiver Supply Current,
Worst Case
CL = 8 pF,
Worst Case Pattern
(Figure 1, Figure 3)
f = 32.5 MHz
f = 37.5 MHz
55
60
75
80
mA
mA
3
www.national.com
Electrical Characteristics (Continued)
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
Parameter
Conditions
Min
Typ
Max
Units
RECEIVER SUPPLY CURRENT
ICCRZ
Receiver Supply Current,
Power Down
Power Down = Low
1
10
µA
Note 1: “Absolute Maximum Ratings” are those values beyond which the safety of the device cannot be guaranteed. They are not meant to imply that the device
should be operated at these limits. The tables of “Electrical Characteristics” specify conditions for device operation.
Note 2: Typical values are given for V
= 5.0V and T = +25˚C.
A
CC
Note 3: Current into device pins is defined as positive. Current out of device pins is defined as negative. Voltages are referenced to ground unless otherwise speci-
fied (except V and ∆V ).
OD
OD
Note 4: ESD Rating:
HBM (1.5 kΩ, 100 pF)
PLL V
≥ 1000V
CC
All other pins ≥ 2000V
EIAJ (0Ω, 200 pF) ≥ 150V
Transmitter Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
LLHT
Parameter
LVDS Low-to-High Transition Time (Figure 2)
LVDS High-to-Low Transition Time (Figure 2)
TxCLK IN Transition Time (Figure 4)
Min
Typ
0.75
0.75
Max
1.5
Units
ns
ns
ns
ps
ps
ns
ns
ns
ns
ns
ns
ps
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
ns
LHLT
1.5
TCIT
8
TCCS
TxOUT Channel-to-Channel Skew (Note 5) (Figure 5)
Transmitter Output Pulse Position for Bit0 (Figure 16)
Transmitter Output Pulse Position for Bit1
Transmitter Output Pulse Position for Bit2
Transmitter Output Pulse Position for Bit3
Transmitter Output Pulse Position for Bit4
Transmitter Output Pulse Position for Bit5
Transmitter Output Pulse Position for Bit6
Transmitter Output Pulse Position for Bit0 (Figure 16)
Transmitter Output Pulse Position for Bit1
Transmitter Output Pulse Position for Bit2
Transmitter Output Pulse Position for Bit3
Transmitter Output Pulse Position for Bit4
Transmitter Output Pulse Position for Bit5
Transmitter Output Pulse Position for Bit6
TxCLK IN Period (Figure 6)
350
350
7.5
TPPos0
TPPos1
TPPos2
TPPos3
TPPos4
TPPos5
TPPos6
TPPos0
TPPos1
TPPos2
TPPos3
TPPos4
TPPos5
TPPos6
TCIP
f = 20 MHz
−200
6.3
150
7.2
12.8
20
13.6
20.8
28
14.6
21.5
28.5
35.6
42.9
300
3.9
27.2
34.5
42.2
−100
2.9
35.2
42.6
100
3.3
f = 40 MHz
6.1
6.6
7.1
9.7
10.2
13.5
17.4
20.8
T
10.7
14.1
17.8
21.4
50
13
17
20.3
25
TCIH
TxCLK IN High Time (Figure 6)
0.35T 0.5T 0.65T
TCIL
TxCLK IN Low Time (Figure 6)
0.35T 0.5T 0.65T
TSTC
TxIN Setup to TxCLK IN (Figure 6)
f = 20 MHz
f = 40 MHz
14
8
THTC
TCCD
TPLLS
TPDD
TxIN Hold to TxCLK IN (Figure 6)
2.5
5
2
@
TxCLK IN to TxCLK OUT Delay 25˚C, VCC = 5.0V (Figure 8)
9.7
10
Transmitter Phase Lock Loop Set (Figure 10)
Transmitter Powerdown Delay (Figure 14)
100
Note 5: This limit based on bench characterization.
www.national.com
4
Receiver Switching Characteristics
Over recommended operating supply and temperature ranges unless otherwise specified
Symbol
CLHT
Parameter
CMOS/TTL Low-to-High Transition Time (Figure 3)
CMOS/TTL High-to-Low Transition Time (Figure 3)
RxCLK OUT Period (Figure 7)
Min
Typ
3.5
2.7
T
Max
6.5
6.5
50
Units
ns
ns
ns
ns
ps
ns
ns
ns
ns
ns
ns
ns
ns
ns
ms
µs
CHLT
RCOP
RSKM
25
1.1
700
19
Receiver Skew Margin (Note 6)
f = 20 MHz
f = 40 MHz
f = 20 MHz
f = 40 MHz
f = 20 MHz
f = 40 MHz
f = 20 MHz
f = 40 MHz
f = 20 MHz
f = 40 MHz
VCC = 5V, TA = 25˚C (Figure 17)
RCOH
RCOL
RSRC
RHRC
RxCLK OUT High Time (Figure 7)
6
RxCLK OUT Low Time (Figure 7)
21.5
10.5
14
RxCLK Setup to RxCLK OUT (Figure 7)
RxCLK Hold to RxCLK OUT (Figure 7)
4.5
16
6.5
7.6
@
RCCD
RPLLS
RPDD
RxCLK IN to RxCLK OUT Delay 25˚C, VCC = 5.0V (Figure 9)
11.9
10
1
Receiver Phase Lock Loop Set (Figure 11)
Receiver Powerdown Delay (Figure 15)
Note 6: Receiver Skew Margin is defined as the valid data sampling region at the receiver inputs. This margin takes into account for transmitter output skew(TCCS)
and the setup and hold time (internal data sampling window), allowing LVDS cable skew dependent on type/length and source clock(TxCLK IN) jitter.
RSKM ≥ cable skew (type, length) + source clock jitter (cycle to cycle).
AC Timing Diagrams
DS012637-4
FIGURE 1. “WORST CASE” Test Pattern
DS012637-5
DS012637-6
FIGURE 2. DS90CR211 (Transmitter) LVDS Output Load and Transition Timing
DS012637-7
DS012637-8
FIGURE 3. DS90CR212 (Receiver) CMOS/TTL Output Load and Transition Timing
5
www.national.com
AC Timing Diagrams (Continued)
DS012637-9
FIGURE 4. DS90CR211 (Transmitter) Input Clock Transition Time
DS012637-10
Measurements at Vdiff = 0V
TCCS measured between earliest and latest initial LVDS edges.
→
TxCLK OUT Differential Low High Edge
FIGURE 5. DS90CR211 (Transmitter) Channel-to-Channel Skew and Pulse Width
DS012637-11
FIGURE 6. DS90CR211 Setup/Hold and High/Low Times
DS012637-12
FIGURE 7. DS90CR212 Setup/Hold and High/Low Times
www.national.com
6
AC Timing Diagrams (Continued)
DS012637-13
FIGURE 8. DS90CR211 (Transmitter) Clock In to Clock Out Delay
DS012637-14
FIGURE 9. DS90CR212 (Receiver) Clock In to Clock Out Delay
DS012637-15
FIGURE 10. DS90CR211 (Transmitter) Phase Lock Loop Set Time
DS012637-16
FIGURE 11. DS90CR212 (Receiver) Phase Lock Loop Set Time
7
www.national.com
AC Timing Diagrams (Continued)
DS012637-17
FIGURE 12. Seven Bits of LVDS in One Clock Cycle
DS012637-18
FIGURE 13. 21 Parallel TTL Data Inputs Mapped to LVDS Outputs (DS90CR211)
DS012637-23
FIGURE 14. Transmitter Powerdown Delay
DS012637-24
FIGURE 15. Receiver Powerdown Delay
www.national.com
8
AC Timing Diagrams (Continued)
DS012637-25
FIGURE 16. Transmitter LVDS Output Pulse Position Measurement
DS012637-26
SW — Setup and Hold Time (Internal data sampling window)
TCCS — Transmitter Output Skew
RSKM ≥ Cable Skew (type, length) + Source Clock Jitter (cycle to cycle)
Cable Skew — Typically 10 ps–40 ps per foot
FIGURE 17. Receiver LVDS Input Skew Margin
DS90CR211 Pin Description—Channel Link Transmitter (Tx)
Pin Name
TxIN
I/O
I
No.
21
3
Description
TTL Level inputs
TxOUT+
O
O
I
Positive LVDS differential data output
Negative LVDS differential data output
TxOUT−
3
TxCLK IN
TxCLK OUT+
TxCLK OUT−
PWR DOWN
VCC
1
TTL level clock input. The rising edge acts as data strobe
Positive LVDS differential clock output
O
O
I
1
1
Negative LVDS differential clock output
1
TTL level input. Assertion (low input) TRI-STATES the outputs, ensuring low current at power down
Power supply pins for TTL inputs
I
4
GND
I
5
Ground pins for TTL inputs
9
www.national.com
DS90CR211 Pin Description—Channel Link Transmitter (Tx) (Continued)
Pin Name
PLL VCC
I/O
No.
1
Description
I
I
I
I
Power supply pin for PLL
Ground pins for PLL
PLL GND
LVDS VCC
LVDS GND
2
1
Power supply pin for LVDS outputs
Ground pins for LVDS outputs
3
DS90CR212 Pin Description—Channel Link Receiver (Rx)
Pin Name
RxIN+
I/O
No.
3
Description
I
I
Positive LVDS differential data inputs
Negative LVDS differential data inputs
TTL level outputs
RxIN−
3
RxOUT
O
I
21
1
RxCLK IN+
RxCLK IN−
RxCLK OUT
PWR DOWN
VCC
Positive LVDS differential clock input
Negative LVDS differential clock input
I
1
O
I
1
TTL level clock output. The rising edge acts as data strobe
TTL level input. Assertion (low input) maintains the receiver outputs in the previous state
Power supply pins for TTL outputs
1
I
4
GND
I
5
Ground pins for TTL outputs
PLL VCC
PLL GND
LVDS VCC
LVDS GND
I
1
Power supply for PLL
I
2
Ground pin for PLL
I
1
Power supply pin for LVDS inputs
I
3
Ground pins for LVDS inputs
In addition to the four or five cable pairs that carry data and
Applications Information
clock, it is recommended to provide at least one additional
conductor (or pair) which connects ground between the
transmitter and receiver. This low impedance ground pro-
vides a common mode return path for the two devices. Some
of the more commonly used cable types for point-to-point ap-
plications include flat ribbon, flex, twisted pair and
Twin-Coax. All are available in a variety of configurations and
options. Flat ribbon cable, flex and twisted pair generally per-
form well in short point-to-point applications while Twin-Coax
is good for short and long applications. When using ribbon
cable, it is recommended to place a ground line between
each differential pair to act as a barrier to noise coupling be-
tween adjacent pairs. For Twin-Coax cable applications, it is
recommended to utilize a shield on each cable pair. All ex-
tended point-to-point applications should also employ an
overall shield surrounding all cable pairs regardless of the
cable type. This overall shield results in improved transmis-
sion parameters such as faster attainable speeds, longer
distances between transmitter and receiver and reduced
problems associated with EMS or EMI.
The Channel Link devices are intended to be used in a wide
variety of data transmission applications. Depending upon
the application the interconnecting media may vary. For ex-
ample, for lower data rate (clock rate) and shorter cable
<
lengths ( 2m), the media electrical performance is less criti-
cal. For higher speed/long distance applications the media’s
performance becomes more critical. Certain cable construc-
tions provide tighter skew (matched electrical length be-
tween the conductors and pairs). Twin-coax for example, has
been demonstrated at distances as great as 10 meters and
with the maximum data transfer of 1.12 Gbit/s. Additional ap-
plications information can be found in the following National
Interface Application Notes:
####
AN =
Topic
AN-1035
PCB Design Guidelines for LVDS and
Link Devices
AN-806
AN-905
Transmission Line Theory
Transmission Line Calculations and
Differential Impedance
The high-speed transport of LVDS signals has been demon-
strated on several types of cables with excellent results.
However, the best overall performance has been seen when
using Twin-Coax cable. Twin-Coax has very low cable skew
and EMI due to its construction and double shielding. All of
the design considerations discussed here and listed in the
supplemental application notes provide the subsystem com-
munications designer with many useful guidelines. It is rec-
ommended that the designer assess the tradeoffs of each
application thoroughly to arrive at a reliable and economical
cable solution.
AN-916
Cable Information
CABLES: A cable interface between the transmitter and re-
ceiver needs to support the differential LVDS pairs. The
21-bit CHANNEL LINK chipset (DS90CR211/212) requires
four pairs of signal wires and the 28-bit CHANNEL LINK
chipset (DS90CR281/282) requires five pairs of signal wires.
The ideal cable/connector interface would have a constant
100Ω differential impedance throughout the path. It is also
@
recommended that cable skew remain below 350 ps ( 40
MHz clock rate) to maintain a sufficient data sampling win-
dow at the receiver.
BOARD LAYOUT: To obtain the maximum benefit from the
noise and EMI reductions of LVDS, attention should be paid
www.national.com
10
the other line of the differential pair. Care should be taken to
ensure that the differential trace impedance match the differ-
ential impedance of the selected physical media (this imped-
ance should also match the value of the termination resistor
that is connected across the differential pair at the receiver’s
input). Finally, the location of the CHANNEL LINK TxOUT/
RxIN pins should be as close as possible to the board edge
so as to eliminate excessive pcb runs. All of these consider-
ations will limit reflections and crosstalk which adversely ef-
fect high frequency performance and EMI.
Applications Information (Continued)
to the layout of differential lines. Lines of a differential pair
should always be adjacent to eliminate noise interference
from other signals and take full advantage of the noise can-
celing of the differential signals. The board designer should
also try to maintain equal length on signal traces for a given
differential pair. As with any high speed design, the imped-
ance discontinuities should be limited (reduce the numbers
of vias and no 90 degree angles on traces). Any discontinui-
ties which do occur on one signal line should be mirrored in
DS012637-20
FIGURE 18. LVDS Serialized Link Termination
UNUSED INPUTS: All unused inputs at the TxW inputs of
the transmitter must be tied to ground. All unused outputs at
the RxOUT outputs of the receiver must then be left floating.
TERMINATION: Use of current mode drivers requires a ter-
minating resistor across the receiver inputs. The CHANNEL
LINK chipset will normally require a single 100Ω resistor be-
tween the true and complement lines on each differential
pair of the receiver input. The actual value of the termination
resistor should be selected to match the differential mode
characteristic impedance (90Ω to 120Ω typical) of the cable.
Figure 18 shows an example. No additional pull-up or
pull-down resistors are necessary as with some other differ-
ential technologies such as PECL. Surface mount resistors
are recommended to avoid the additional inductance that ac-
companies leaded resistors. These resistors should be
placed as close as possible to the receiver input pins to re-
duce stubs and effectively terminate the differential lines.
DS012637-21
FIGURE 19. CHANNEL LINK
Decoupling Configuration
CLOCK JITTER: The CHANNEL LINK devices employ a
PLL to generate and recover the clock transmitted across the
LVDS interface. The width of each bit in the serialized LVDS
data stream is one-seventh the clock period. For example, a
40 MHz clock has a period of 25 ns which results in a data bit
width of 3.57 ns. Differential skew (∆t within one differential
pair), interconnect skew (∆t of one differential pair to an-
other) and clock jitter will all reduce the available window for
sampling the LVDS serial data streams. Care must be taken
to ensure that the clock input to the transmitter be a clean
low noise signal. Individual bypassing of each VCC to ground
will minimize the noise passed on to the PLL, thus creating a
low jitter LVDS clock. These measures provide more margin
for channel-to-channel skew and interconnect skew as a part
of the overall jitter/skew budget.
DECOUPLING CAPACITORS: Bypassing capacitors are
needed to reduce the impact of switching noise which could
limit performance. For
a conservative approach three
parallel-connected decoupling capacitors (Multi-Layered Ce-
ramic type in surface mount form factor) between each VCC
and the ground plane(s) are recommended. The three ca-
pacitor values are 0.1 µF, 0.01µF and 0.001 µF. An example
is shown in Figure 19. The designer should employ wide
traces for power and ground and ensure each capacitor has
its own via to the ground plane. If board space is limiting the
number of bypass capacitors, the PLL VCC should receive
the most filtering/bypassing. Next would be the LVDS VCC
pins and finally the logic VCC pins.
11
www.national.com
Applications Information (Continued)
DS012637-22
FIGURE 20. Single-Ended and Differential Waveforms
COMMON MODE vs. DIFFERENTIAL MODE NOISE MAR-
GIN: The typical signal swing for LVDS is 300 mV centered
at +1.2V. The CHANNEL LINK receiver supports a 100 mV
threshold therefore providing approximately 200 mV of differ-
ential noise margin. Common mode protection is of more im-
portance to the system’s operation due to the differential
data transmission. LVDS supports an input voltage range of
4.5V and the Powerdown pin is above 2V. Either device may
be placed into a powerdown mode at any time by asserting
the Powerdown pin (active low). Total power dissipation for
each device will decrease to 5 µW (typical).
The CHANNEL LINK chipset is designed to protect itself
from accidental loss of power to either the transmitter or re-
ceiver. If power to the transmit board is lost, the receiver
clocks (input and output) stop. The data outputs (RxOUT) re-
tain the states they were in when the clocks stopped. When
the receiver board loses power, the receiver inputs are
±
Ground to +2.4V. This allows for a 1.0V shifting of the cen-
ter point due to ground potential differences and common
mode noise.
POWER SEQUENCING AND POWERDOWN MODE: Out-
puts of the CHANNEL LINK transmitter remain in
TRI-STATE® until the power supply reaches 3V. Clock and
data outputs will begin to toggle 10 ms after VCChas reached
shorted to V
through an internal diode. Current is limited
CC
(5 mA per input) by the fixed current mode drivers, thus
avoiding the potential for latchup when powering the device.
www.national.com
12
Physical Dimensions inches (millimeters) unless otherwise noted
48-Lead Molded Thin Shrink Small Outline Package, JEDEC
Order Number DS90CR211MTD or DS90CR212MTD
NS Package Number MTD48
LIFE SUPPORT POLICY
NATIONAL’S PRODUCTS ARE NOT AUTHORIZED FOR USE AS CRITICAL COMPONENTS IN LIFE SUPPORT
DEVICES OR SYSTEMS WITHOUT THE EXPRESS WRITTEN APPROVAL OF THE PRESIDENT AND GENERAL
COUNSEL OF NATIONAL SEMICONDUCTOR CORPORATION. As used herein:
1. Life support devices or systems are devices or
systems which, (a) are intended for surgical implant
into the body, or (b) support or sustain life, and
whose failure to perform when properly used in
accordance with instructions for use provided in the
labeling, can be reasonably expected to result in a
significant injury to the user.
2. A critical component is any component of a life
support device or system whose failure to perform
can be reasonably expected to cause the failure of
the life support device or system, or to affect its
safety or effectiveness.
National Semiconductor
Corporation
Americas
Tel: 1-800-272-9959
Fax: 1-800-737-7018
Email: support@nsc.com
National Semiconductor
Europe
National Semiconductor
Asia Pacific Customer
Response Group
Tel: 65-2544466
Fax: 65-2504466
National Semiconductor
Japan Ltd.
Tel: 81-3-5639-7560
Fax: 81-3-5639-7507
Fax: +49 (0) 180-530 85 86
Email: europe.support@nsc.com
Deutsch Tel: +49 (0) 69 9508 6208
English Tel: +44 (0) 870 24 0 2171
Français Tel: +33 (0) 1 41 91 8790
Email: ap.support@nsc.com
www.national.com
National does not assume any responsibility for use of any circuitry described, no circuit patent licenses are implied and National reserves the right at any time without notice to change said circuitry and specifications.
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Transportation and Automotive www.ti.com/automotive
Power Mgmt
Microcontrollers
RFID
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明