HPA00900AIDCNR [TI]
26-V, Bidirectional, Zero-Drift, High-Side, I<sup>2</sup>C Out Current/Power Monitor 8-SOT-23 -25 to 85;
| 型号： | HPA00900AIDCNR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 26-V, Bidirectional, Zero-Drift, High-Side, I<sup>2</sup>C Out Current/Power Monitor 8-SOT-23 -25 to 85 光电二极管 |
| 文件： | 总40页 (文件大小：984K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
Zerø-Drift, Bi-Directional
CURRENT/POWER MONITOR with I2C™ Interface
Check for Samples: INA219
1
FEATURES
DESCRIPTION
The INA219 is a high-side current shunt and power
23
•
SENSES BUS VOLTAGES FROM 0V TO +26V
REPORTS CURRENT, VOLTAGE, AND POWER
16 PROGRAMMABLE ADDRESSES
monitor with an I2C interface. The INA219 monitors
both shunt drop and supply voltage, with
•
•
•
programmable conversion times and filtering.
A
programmable calibration value, combined with an
internal multiplier, enables direct readouts in
amperes. An additional multiplying register calculates
power in watts. The I2C interface features 16
programmable addresses.
HIGH ACCURACY: 0.5% (Max) OVER
TEMPERATURE (INA219B)
•
•
•
FILTERING OPTIONS
CALIBRATION REGISTERS
SOT23-8 AND SO-8 PACKAGES
The INA219 is available in two grades: A and B. The
B grade version has higher accuracy and higher
precision specifications.
APPLICATIONS
•
•
•
•
•
•
•
•
SERVERS
The INA219 senses across shunts on buses that can
vary from 0V to 26V. The device uses a single +3V to
+5.5V supply, drawing a maximum of 1mA of supply
current. The INA219 operates from –40°C to +125°C.
TELECOM EQUIPMENT
NOTEBOOK COMPUTERS
POWER MANAGEMENT
BATTERY CHARGERS
WELDING EQUIPMENT
POWER SUPPLIES
TEST EQUIPMENT
RELATED PRODUCTS
DESCRIPTION
DEVICE
Current/Power Monitor with Watchdog,
Peak-Hold, and Fast Comparator Functions
INA209
Zerø-Drift, Low-Cost, Analog Current Shunt
Monitor Series in Small Package
INA210, INA211, INA212,
INA213, INA214
VS
VIN+ VIN-
(Supply Voltage)
INA219
Power Register
´
Data
CLK
A0
I2C
Interface
Current Register
PGA
ADC
A1
Voltage Register
GND
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
I2C is a trademark of NXP Semiconductors.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008–2011, Texas Instruments Incorporated
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
Table 1. PACKAGING INFORMATION(1)
PRODUCT
PACKAGE-LEAD
SO-8
PACKAGE DESIGNATOR
PACKAGE MARKING
D
I219A
A219
I219B
B219
INA219A
SOT23-8
SO-8
DCN
D
INA219B
SOT23-8
DCN
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the
INA219 product folder at www.ti.com.
ABSOLUTE MAXIMUM RATINGS(1)
Over operating free-air temperature range (unless otherwise noted).
INA219
UNIT
V
Supply Voltage, VS
6
(2)
Differential (VIN+) – (VIN–
)
–26 to +26
V
Analog Inputs,
VIN+, VIN–
Common-Mode
-0.3 to +26
V
SDA
SCL
GND – 0.3 to +6
V
GND – 0.3 to VS + 0.3
V
Input Current Into Any Pin
Open-Drain Digital Output Current
Operating Temperature
Storage Temperature
5
10
mA
mA
°C
°C
°C
V
–40 to +125
–65 to +150
+150
Junction Temperature
Human Body Model
4000
ESD Ratings
Charged-Device Model
Machine Model (MM)
750
V
200
V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
(2) VIN+ and VIN– may have a differential voltage of –26V to +26V; however, the voltage at these pins must not exceed the range –0.3V to
+26V.
2
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
ELECTRICAL CHARACTERISTICS: VS = +3.3V
Boldface limits apply over the specified temperature range, TA = –25°C to +85°C.
At TA = +25°C, VIN+ = 12V, VSENSE = (VIN+ – VIN–) = 32mV, PGA = ÷ 1, and BRNG(1) = 1, unless otherwise noted.
INA219A
INA219B
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
INPUT
Full-Scale Current Sense (Input) Voltage Range
PGA = ÷ 1
PGA = ÷ 2
PGA = ÷ 4
PGA = ÷ 8
BRNG = 1
BRNG = 0
VIN+ = 0V to 26V
PGA = ÷ 1
PGA = ÷ 2
PGA = ÷ 4
PGA = ÷ 8
0
0
±40
±80
±160
±320
32
0
0
±40
±80
±160
±320
32
mV
mV
mV
mV
V
0
0
0
0
Bus Voltage (Input Voltage) Range(2)
0
0
0
16
0
16
V
Common-Mode Rejection
Offset Voltage, RTI(3)
CMRR
100
120
±10
±20
±30
±40
0.1
10
100
120
±10
±20
±30
±40
0.1
10
dB
VOS
±100
±125
±150
±200
±50(4)
±75
μV
μV
±75
μV
±100
μV
vs Temperature
vs Power Supply
Current Sense Gain Error
vs Temperature
Input Impedance
VIN+ Pin
μV/°C
μV/V
m%
m%/°C
PSRR
VS = 3V to 5.5V
Active Mode
±40
1
±40
1
20
20
μA
VIN– Pin
20 || 320
20 || 320
μA || kΩ
Input Leakage(5)
Power-Down Mode
VIN+ Pin
0.1
0.1
±0.5
±0.5
0.1
0.1
±0.5
±0.5
μA
μA
VIN– Pin
DC ACCURACY
ADC Basic Resolution
1 LSB Step Size
Shunt Voltage
12
12
Bits
10
4
10
4
μV
mV
%
Bus Voltage
Current Measurement Error
over Temperature
Bus Voltage Measurement Error
over Temperature
Differential Nonlinearity
ADC TIMING
±0.2
±0.5
±1
±0.2
±0.3
±0.5
±0.5
±1
%
±0.2
±0.1
±0.5
±1
±0.2
±0.1
%
%
LSB
ADC Conversion Time
12-Bit
11-Bit
10-Bit
9-Bit
532
276
148
84
586
304
163
93
532
276
148
84
586
304
163
93
μs
μs
μs
μs
μs
Minimum Convert Input Low Time
4
4
(1) BRNG is bit 13 of the Configuration Register.
(2) This parameter only expresses the full-scale range of the ADC scaling. In no event should more than 26V be applied to this device.
(3) Referred-to-input (RTI).
(4) Shaded cells indicate improved specifications of the INA219B.
(5) Input leakage is positive (current flowing into the pin) for the conditions shown at the top of the table. Negative leakage currents can
occur under different input conditions.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
ELECTRICAL CHARACTERISTICS: VS = +3.3V (continued)
Boldface limits apply over the specified temperature range, TA = –25°C to +85°C.
At TA = +25°C, VIN+ = 12V, VSENSE = (VIN+ – VIN–) = 32mV, PGA = ÷ 1, and BRNG(1) = 1, unless otherwise noted.
INA219A
INA219B
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
MIN
TYP
MAX
UNIT
SMBus
SMBus Timeout(6)
28
35
28
35
ms
DIGITAL INPUTS
(SDA as Input, SCL, A0, A1)
Input Capacitance
3
3
pF
Leakage Input Current
Input Logic Levels:
0 ≤ VIN ≤ VS
0.1
1
0.1
1
6
μA
VIH
0.7 (VS)
6
0.7 (VS)
V
VIL
–0.3
0.3 (VS)
–0.3
0.3 (VS)
V
Hysteresis
500
500
mV
OPEN-DRAIN DIGITAL OUTPUTS (SDA)
Logic '0' Output Level
High-Level Output Leakage Current
POWER SUPPLY
ISINK = 3mA
VOUT = VS
0.15
0.1
0.4
1
0.15
0.1
0.4
1
V
μA
Operating Supply Range
Quiescent Current
+3
+5.5
1
+3
+5.5
1
V
mA
μA
V
0.7
6
0.7
6
Quiescent Current, Power-Down Mode
Power-On Reset Threshold
TEMPERATURE RANGE
Specified Temperature Range
Operating Temperature Range
Thermal Resistance(7)
SOT23-8
15
15
2
2
–25
–40
+85
–25
–40
+85
°C
°C
+125
+125
θJA
142
120
142
120
°C/W
°C/W
SO-8
(6) SMBus timeout in the INA219 resets the interface any time SCL or SDA is low for over 28ms.
(7) θJA value is based on JEDEC low-K board.
4
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
PIN CONFIGURATIONS
DCN PACKAGE
SOT23-8
(Top View)
D PACKAGE
SO-8
(Top View)
VIN+
VIN-
A1
1
2
3
4
8
7
6
5
A1
A0
1
2
3
4
8
7
6
5
VIN+
VIN-
GND
VS
A0
GND
VS
SDA
SCL
SDA
SCL
PIN DESCRIPTIONS: SOT23-8
SOT23-8
(DCN)
PIN NO
NAME
DESCRIPTION
Positive differential shunt voltage. Connect to positive side of shunt resistor.
1
VIN+
Negative differential shunt voltage. Connect to negative side of shunt resistor. Bus voltage is measured
from this pin to ground.
2
VIN–
3
4
5
6
7
8
GND
VS
Ground.
Power supply, 3V to 5.5V.
SCL
SDA
A0
Serial bus clock line.
Serial bus data line.
Address pin. Table 2 shows pin settings and corresponding addresses.
Address pin. Table 2 shows pin settings and corresponding addresses.
A1
PIN DESCRIPTIONS: SO-8
SO-8
(D)
PIN NO
NAME
A1
DESCRIPTION
Address pin. Table 2 shows pin settings and corresponding addresses.
Address pin. Table 2 shows pin settings and corresponding addresses.
Serial bus data line.
1
2
3
4
5
6
A0
SDA
SCL
VS
Serial bus clock line.
Power supply, 3V to 5.5V.
GND
Ground.
Negative differential shunt voltage. Connect to negative side of shunt resistor. Bus voltage is measured
from this pin to ground.
7
8
VIN–
VIN+
Positive differential shunt voltage. Connect to positive side of shunt resistor.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, VIN+ = 12V, VSENSE = (VIN+ – VIN–) = 32mV, PGA = ÷ 1, and BRNG = 1, unless otherwise noted.
FREQUENCY RESPONSE
ADC SHUNT OFFSET vs TEMPERATURE
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
100
80
320mV Range
160mV Range
60
40
20
0
-20
-40
-60
-80
-100
80mV Range
40mV Range
100
1k
10k
100k
1M
125
125
-25
0
25
50
10
-40
75
100
125
Input Frequency (Hz)
Temperature (°C)
Figure 1.
Figure 2.
ADC SHUNT GAIN ERROR vs TEMPERATURE
ADC BUS VOLTAGE OFFSET vs TEMPERATURE
100
80
50
45
40
35
30
25
20
15
10
5
60
40
20
160mV Range
320mV Range
0
-20
-40
-60
-80
-100
16V Range
32V Range
40mV Range
80mV Range
0
0
25
50
-25
0
25
50
-40 -25
75
100
-40
75
100
125
Temperature (°C)
Temperature (°C)
Figure 3.
Figure 4.
ADC BUS GAIN ERROR vs TEMPERATURE
INTEGRAL NONLINEARITY vs INPUT VOLTAGE
20
15
100
80
60
10
40
16V
32V
5
20
0
0
-20
-40
-60
-80
-100
-5
-10
-15
-20
-0.2 -0.1
0
-0.4 -0.3
0.1
0.2
0.3
0.4
0
25
50
-40 -25
75
100
Input Voltage (V)
Temperature (°C)
Figure 5.
Figure 6.
6
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VIN+ = 12V, VSENSE = (VIN+ – VIN–) = 32mV, PGA = ÷ 1, and BRNG = 1, unless otherwise noted.
INPUT CURRENTS WITH LARGE DIFFERENTIAL
VOLTAGES
(VIN+ at 12V, Sweep of VIN–
)
ACTIVE IQ vs TEMPERATURE
2.0
1.5
1.2
1.0
0.8
0.6
0.4
0.2
0
VS+ = 5V
VS = 5V
1.0
0.5
VS+ = 3V
VS+ = 3V
0
VS = 3V
-0.5
-1.0
-1.5
VS+ = 5V
0
5
10
15
20
25
30
0
25
50
-40 -25
75
100
125
VIN- Voltage (V)
Temperature (°C)
Figure 7.
Figure 8.
SHUTDOWN IQ vs TEMPERATURE
ACTIVE IQ vs I2C CLOCK FREQUENCY
16
14
12
10
8
1.0
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
VS = 5V
VS = 5V
VS = 3V
VS = 3V
6
4
2
0
0
25
50
75
100
125
-40 -25
1k
10k
100k
1M
10M
Temperature (°C)
SCL Frequency (Hz)
Figure 9.
Figure 10.
SHUTDOWN IQ vs I2C CLOCK FREQUENCY
300
250
200
150
100
50
VS = 5V
VS = 3V
0
1k
10k
100k
1M
10M
SCL Frequency (Hz)
Figure 11.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
REGISTER BLOCK DIAGRAM
Power(1)
Bus Voltage(1)
´
Current(1)
Shunt Voltage
Channel
ADC
Bus Voltage
Channel
Full-Scale Calibration(2)
Shunt Voltage(1)
´
PGA
(In Configuration Register)
NOTES:
(1) Read-only
(2) Read/write
Data Registers
Figure 12. INA219 Register Block Diagram
8
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
APPLICATION INFORMATION
The INA219 is a digital current-shunt monitor with an
I2C and SMBus-compatible interface. It provides
digital current, voltage, and power readings
The I2C interface is used throughout this data sheet
as the primary example, with SMBus protocol
specified only when a difference between the two
systems is being addressed. Two bidirectional lines,
SCL and SDA, connect the INA219 to the bus. Both
SCL and SDA are open-drain connections.
necessary
for
accurate
decision-making
in
precisely-controlled systems. Programmable registers
allow flexible configuration for measurement
resolution,
versus-triggered
information appears at the end of this data sheet,
beginning with Table 4. See the Register Block
Diagram for a block diagram of the INA219.
and
operation.
continuous-
Detailed register
The device that initiates the transfer is called a
master, and the devices controlled by the master are
slaves. The bus must be controlled by a master
device that generates the serial clock (SCL), controls
the bus access, and generates START and STOP
conditions.
INA219 TYPICAL APPLICATION
To address a specific device, the master initiates a
START condition by pulling the data signal line (SDA)
from a HIGH to a LOW logic level while SCL is HIGH.
All slaves on the bus shift in the slave address byte
on the rising edge of SCL, with the last bit indicating
whether a read or write operation is intended. During
the ninth clock pulse, the slave being addressed
responds to the master by generating an
Acknowledge and pulling SDA LOW.
Figure 13 shows a typical application circuit for the
INA219. Use
a
0.1μF ceramic capacitor for
power-supply bypassing, placed as closely as
possible to the supply and ground pins.
The input filter circuit consisting of RF1, RF2, and CF is
not necessary in most applications. If the need for
filtering is unknown, reserve board space for the
components and install 0Ω resistors unless a filter is
needed. See the Filtering and Input Considerations
section.
Data transfer is then initiated and eight bits of data
are sent, followed by an Acknowledge bit. During
data transfer, SDA must remain stable while SCL is
HIGH. Any change in SDA while SCL is HIGH is
interpreted as a START or STOP condition.
The pull-up resistors shown on the SDA and SCL
lines are not needed if there are pull-up resistors on
these same lines elsewhere in the system. Resistor
values shown are typical: consult either the I2C or
SMBus specification to determine the acceptable
minimum or maximum values.
Once all data have been transferred, the master
generates a STOP condition, indicated by pulling
SDA from LOW to HIGH while SCL is HIGH. The
INA219 includes a 28ms timeout on its interface to
prevent locking up an SMBus.
BUS OVERVIEW
The INA219 offers compatibility with both I2C and
SMBus interfaces. The I2C and SMBus protocols are
essentially compatible with one another.
Current
Supply Voltage
(INA219 Power Supply Range is
3V to 5.5V)
Shunt
Power Bus
(0V to 26V)
Load
RF1
RF2
CBYPASS
0.1mF
CF
(typical)
RPULLUP
RPULLUP
VIN+
VIN-
3.3kW
3.3kW
(typical)
(typical)
INA219
SDA
Power Register
Current Register
Voltage Register
´
Data (SDA)
Clock (SCL)
SCL
A0
I2C
Interface
PGA
ADC
A1
GND
Figure 13. Typical Application Circuit
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Serial Bus Address
WRITING TO/READING FROM THE INA219
To communicate with the INA219, the master must
first address slave devices via a slave address byte.
The slave address byte consists of seven address
bits, and a direction bit indicating the intent of
executing a read or write operation.
Accessing a particular register on the INA219 is
accomplished by writing the appropriate value to the
register pointer. Refer to Table 4 for a complete list of
registers and corresponding addresses. The value for
the register pointer as shown in Figure 17 is the first
byte transferred after the slave address byte with the
R/W bit LOW. Every write operation to the INA219
requires a value for the register pointer.
The INA219 has two address pins, A0 and A1.
Table 2 describes the pin logic levels for each of the
16 possible addresses. The state of pins A0 and A1
is sampled on every bus communication and should
be set before any activity on the interface occurs. The
address pins are read at the start of each
communication event.
Writing to a register begins with the first byte
transmitted by the master. This byte is the slave
address, with the R/W bit LOW. The INA219 then
acknowledges receipt of a valid address. The next
byte transmitted by the master is the address of the
register to which data will be written. This register
address value updates the register pointer to the
desired register. The next two bytes are written to the
register addressed by the register pointer. The
INA219 acknowledges receipt of each data byte. The
master may terminate data transfer by generating a
START or STOP condition.
Table 2. INA219 Address Pins and
Slave Addresses
A1
A0
SLAVE ADDRESS
1000000
1000001
1000010
1000011
1000100
1000101
1000110
1000111
1001000
1001001
1001010
1001011
1001100
1001101
1001110
1001111
GND
GND
GND
GND
VS+
GND
VS+
SDA
SCL
GND
VS+
When reading from the INA219, the last value stored
in the register pointer by a write operation determines
which register is read during a read operation. To
change the register pointer for a read operation, a
new value must be written to the register pointer. This
write is accomplished by issuing a slave address byte
with the R/W bit LOW, followed by the register pointer
byte. No additional data are required. The master
then generates a START condition and sends the
slave address byte with the R/W bit HIGH to initiate
the read command. The next byte is transmitted by
the slave and is the most significant byte of the
register indicated by the register pointer. This byte is
followed by an Acknowledge from the master; then
the slave transmits the least significant byte. The
master acknowledges receipt of the data byte. The
master may terminate data transfer by generating a
Not-Acknowledge after receiving any data byte, or
generating a START or STOP condition. If repeated
reads from the same register are desired, it is not
necessary to continually send the register pointer
bytes; the INA219 retains the register pointer value
until it is changed by the next write operation.
VS+
VS+
SDA
SCL
GND
VS+
VS+
SDA
SDA
SDA
SDA
SCL
SCL
SCL
SCL
SDA
SCL
GND
VS+
SDA
SCL
Serial Interface
The INA219 operates only as a slave device on the
I2C bus and SMBus. Connections to the bus are
made via the open-drain I/O lines SDA and SCL. The
SDA and SCL pins feature integrated spike
suppression filters and Schmitt triggers to minimize
the effects of input spikes and bus noise. The INA219
supports the transmission protocol for fast (1kHz to
400kHz) and high-speed (1kHz to 3.4MHz) modes.
All data bytes are transmitted most significant byte
first.
Figure 14 and Figure 15 show read and write
operation timing diagrams, respectively. Note that
register bytes are sent most-significant byte first,
followed by the least significant byte. Figure 16
shows the timing diagram for the SMBus Alert
response operation. Figure 17 illustrates a typical
register pointer configuration.
10
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
Figure 15. Timing Diagram for Read Word Format
Figure 14. Timing Diagram for Write Word Format
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
ALERT
1
9
1
9
SCL
SDA
0
0
0
1
1
0
0
R/W
1
0
0
A3
A2
A1
A0
0
Start By
Master
ACK By
From
INA219
NACK By Stop By
INA219
Master
Master
Frame 1 SMBus ALERT Response Address Byte
Frame 2 Slave Address Byte(1)
NOTE (1): The value of the Slave Address Byte is determined by the settings of the A0 and A1 pins. Refer to Table 1.
Figure 16. Timing Diagram for SMBus ALERT
1
9
1
9
SCL
SDA
¼
1
0
0
A3
A2
A1
A0 R/W
P7
P6
P5
P4
P3
P2
P1
P0
Stop
Start By
Master
ACK By
ACK By
INA219
INA219
Frame 1 Two-Wire Slave Address Byte(1)
Frame 2 Register Pointer Byte
NOTE (1): The value of the Slave Address Byte is determined by the settings of the A0 and A1 pins. Refer to Table 1.
Figure 17. Typical Register Pointer Set
12
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
High-Speed I2C Mode
The master then generates a repeated start condition
(a repeated start condition has the same timing as
the start condition). After this repeated start condition,
the protocol is the same as F/S mode, except that
transmission speeds up to 3.4Mbps are allowed.
Instead of using a stop condition, repeated start
conditions should be used to secure the bus in
HS-mode. A stop condition ends the HS-mode and
switches all the internal filters of the INA219 to
support the F/S mode.
When the bus is idle, both the SDA and SCL lines are
pulled high by the pull-up devices. The master
generates a start condition followed by a valid serial
byte containing High-Speed (HS) master code
00001XXX. This transmission is made in fast
(400kbps) or standard (100kbps) (F/S) mode at no
more than 400kbps. The INA219 does not
acknowledge the HS master code, but does
recognize it and switches its internal filters to support
3.4Mbps operation.
t(LOW)
tF
tR
t(HDSTA)
SCL
SDA
t(SUSTO)
t(HDSTA)
t(HIGH) t(SUSTA)
t(HDDAT)
t(SUDAT)
t(BUF)
P
S
S
P
Figure 18. Bus Timing Diagram
Bus Timing Diagram Definitions
FAST MODE
HIGH-SPEED MODE
PARAMETER
MIN
MAX
MIN
MAX
UNITS
SCL Operating Frequency
f(SCL)
t(BUF)
0.001
0.4
0.001
3.4
MHz
Bus Free Time Between STOP and START
Condition
600
100
160
100
ns
Hold time after repeated START condition.
t(HDSTA)
ns
After this period, the first clock is generated.
Repeated START Condition Setup Time
STOP Condition Setup Time
Data Hold Time
t(SUSTA)
t(SUSTO)
t(HDDAT)
t(SUDAT)
t(LOW)
t(HIGH)
tF
100
100
0
100
100
0
ns
ns
ns
ns
ns
ns
ns
ns
ns
Data Setup Time
100
1300
600
10
SCL Clock LOW Period
160
60
SCL Clock HIGH Period
Clock/Data Fall Time
300
300
160
160
Clock/Data Rise Time
tR
Clock/Data Rise Time for SCLK ≤ 100kHz
tR
1000
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Power-Up Conditions
(Configuration Register, BADC bits). The Mode
control in the Configuration Register also permits
selecting modes to convert only voltage or current,
either continuously or in response to an event
(triggered).
Power-up conditions apply to a software reset via the
RST bit (bit 15) in the Configuration Register, or the
I2C bus General Call Reset.
BASIC ADC FUNCTIONS
All current and power calculations are performed in
the background and do not contribute to conversion
time; conversion times shown in the Electrical
Characteristics table can be used to determine the
actual conversion time.
The two analog inputs to the INA219, VIN+ and VIN–
,
connect to a shunt resistor in the bus of interest. The
INA219 is typically powered by a separate supply
from +3V to +5.5V. The bus being sensed can vary
from 0V to 26V. There are no special considerations
for power-supply sequencing (for example, a bus
voltage can be present with the supply voltage off,
and vice-versa). The INA219 senses the small drop
across the shunt for shunt voltage, and senses the
voltage with respect to ground from VIN– for the bus
voltage. Figure 19 illustrates this operation.
Power-Down mode reduces the quiescent current
and turns off current into the INA219 inputs, avoiding
any supply drain. Full recovery from Power-Down
requires 40μs. ADC Off mode (set by the
Configuration Register, MODE bits) stops all
conversions.
Writing any of the triggered convert modes into the
Configuration Register (even if the desired mode is
already programmed into the register) triggers a
single-shot conversion. Table 7 lists the triggered
convert mode settings.
When the INA219 is in the normal operating mode
(that is, MODE bits of the Configuration Register are
set to '111'), it continuously converts the shunt
voltage up to the number set in the shunt voltage
averaging function (Configuration Register, SADC
bits). The device then converts the bus voltage up to
the number set in the bus voltage averaging
VSHUNT = VIN+ - VIN-
Typically < 50mV
-
+
Current
Shunt
INA219 Power-Supply Voltage
3V to 5.5V
Supply
Load
3.3V Supply
VIN+
VIN-
VS
INA219
Power Register
´
Data (SDA)
Clock (SCL)
I2C
VBUS = VIN- - GND
Current Register
Interface
A0
Range of 0V to 26V
PGA
ADC
Typical Application 12V
A1
Voltage Register
GND
Figure 19. INA219 Configured for Shunt and Bus Voltage Measurement
14
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
Compatibility with TI Hot Swap Controllers
Although the INA219 can be read at any time, and
the data from the last conversion remain available,
the Conversion Ready bit (Status Register, CNVR bit)
is provided to help co-ordinate one-shot or triggered
conversions. The Conversion Ready bit is set after all
conversions, averaging, and multiplication operations
are complete.
The INA219 is designed for compatibility with hot
swap controllers such the TI TPS2490. The TPS2490
uses a high-side shunt with a limit at 50mV; the
INA219 full-scale range of 40mV enables the use of
the same shunt for current sensing below this limit.
When sensing is required at (or through) the 50mV
sense point of the TPS2490, the PGA of the INA219
can be set to ÷2 to provide an 80mV full-scale range.
The Conversion Ready bit clears under these
conditions:
1. Writing to the Configuration Register, except
when configuring the MODE bits for Power Down
or ADC off (Disable) modes;
Filtering and Input Considerations
Measuring current is often noisy, and such noise can
be difficult to define. The INA219 offers several
options for filtering by choosing resolution and
averaging in the Configuration Register. These
filtering options can be set independently for either
voltage or current measurement.
2. Reading the Status Register; or
3. Triggering a single-shot conversion with the
Convert pin.
Power Measurement
The internal ADC is based on a delta-sigma (ΔΣ)
front-end with a 500kHz (±30%) typical sampling rate.
This architecture has good inherent noise rejection;
however, transients that occur at or very close to the
sampling rate harmonics can cause problems.
Because these signals are at 1MHz and higher, they
can be dealt with by incorporating filtering at the input
of the INA219. The high frequency enables the use of
low-value series resistors on the filter for negligible
effects on measurement accuracy. In general, filtering
the INA219 input is only necessary if there are
transients at exact harmonics of the 500kHz (±30%)
sampling rate (>1MHz). Filter using the lowest
possible series resistance and ceramic capacitor.
Recommended values are 0.1μF to 1.0μF. Figure 20
shows the INA219 with an additonal filter added at
the input.
Current and bus voltage are converted at different
points in time, depending on the resolution and
averaging mode settings. For instance, when
configured for 12-bit and 128 sample averaging, up to
68ms in time between sampling these two values is
possible. Again, these calculations are performed in
the background and do not add to the overall
conversion time.
PGA Function
If larger full-scale shunt voltages are desired, the
INA219 provides a PGA function that increases the
full-scale range up to 2, 4, or 8 times (320mV).
Additionally, the bus voltage measurement has two
full-scale ranges: 16V or 32V.
Current
Shunt
Supply
Load
RFILTER 10W
RFILTER 10W
Supply Voltage
3.3V Supply
0.1mF to 1mF
Ceramic Capacitor
VIN+ VIN-
VS
INA219
Power Register
´
Data (SDA)
Clock (SCL)
I2C
Interface
Current Register
Voltage Register
A0
A1
PGA
ADC
GND
Figure 20. INA219 with Input Filtering
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Simple Current Shunt Monitor Usage
(No Programming Necessary)
Overload conditions are another consideration for the
INA219 inputs. The INA219 inputs are specified to
tolerate 26V across the inputs. A large differential
scenario might be a short to ground on the load side
of the shunt. This type of event can result in full
power-supply voltage across the shunt (as long the
power supply or energy storage capacitors support it).
It must be remembered that removing a short to
ground can result in inductive kickbacks that could
exceed the 26V differential and common-mode rating
of the INA219. Inductive kickback voltages are best
dealt with by zener-type transient-absorbing devices
(commonly called transzorbs) combined with
sufficient energy storage capacitance.
The INA219 can be used without any programming if
it is only necessary to read a shunt voltage drop and
bus voltage with the default 12-bit resolution, 320mV
shunt full-scale range (PGA = ÷8), 32V bus full-scale
range, and continuous conversion of shunt and bus
voltage.
Without programming, current is measured by
reading the shunt voltage. The Current Register and
Power Register are only available if the Calibration
Register contains a programmed value.
Programming the INA219
In applications that do not have large energy storage
electrolytics on one or both sides of the shunt, an
input overstress condition may result from an
excessive dV/dt of the voltage applied to the input. A
hard physical short is the most likely cause of this
event, particularly in applications with no large
electrolytics present. This problem occurs because an
excessive dV/dt can activate the ESD protection in
the INA219 in systems where large currents are
available. Testing has demonstrated that the addition
of 10Ω resistors in series with each input of the
INA219 sufficiently protects the inputs against dV/dt
failure up to the 26V rating of the INA219. These
resistors have no significant effect on accuracy.
The default power-up states of the registers are
shown in the INA219 register descriptions section of
this data sheet. These registers are volatile, and if
programmed to other than default values, must be
re-programmed at every device power-up. Detailed
information on programming the Calibration Register
specifically is given in the section, Programming the
INA219 Power Measurement Engine
.
16
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
PROGRAMMING THE INA219 POWER
MEASUREMENT ENGINE
Calibration Register can also be selected to provide
values in the Current and Power Registers that either
provide direct decimal equivalents of the values being
measured, or yield a round LSB number. After these
choices have been made, the Calibration Register
also offers possibilities for end user system-level
calibration, where the value is adjusted slightly to
cancel total system error.
Calibration Register and Scaling
The Calibration Register makes it possible to set the
scaling of the Current and Power Registers to
whatever values are most useful for
application. One strategy may be to set the
Calibration Register such that the largest possible
number is generated in the Current Register or Power
Register at the expected full-scale point; this
approach yields the highest resolution. The
a given
Below are two examples for configuring the INA219
calibration. Both examples are written so the
information directly relates to the calibration setup
found in the INA219EVM software.
Calibration Example 1: Calibrating the INA219 with no possibility for overflow. (Note that the numbers
used in this example are the same used with the INA219EVM software as shown in Figure 21.)
1. Establish the following parameters:
VBUS_MAX = 32
VSHUNT_MAX = 0.32
RSHUNT = 0.5
2. Using Equation 1, determine the maximum possible current .
VSHUNT_MAX
MaxPossible_I =
RSHUNT
MaxPossible_I = 0.64
(1)
3. Choose the desired maximum current value. This value is selected based on system expectations.
Max_Expected_I = 0.6
4. Calculate the possible range of current LSBs. To calculate this range, first compute a range of LSBs that is
appropriate for the design. Next, select an LSB within this range. Note that the results will have the most
resolution when the minimum LSB is selected. Typically, an LSB is selected to be the nearest round number
to the minimum LSB value.
Max_Expected_I
Minimum_LSB =
32767
-6
Minimum_LSB = 18.311 ´ 10
(2)
Max_Expected_I
Maximum_LSB =
4096
-6
Maximum_LSB = 146.520 ´ 10
(3)
Choose an LSB in the range: Minimum_LSB<Selected_LSB < Maximum_LSB
Current_LSB = 20 × 10–6
Note:
This value was selected to be a round number near the Minimum_LSB. This selection allows for
good resolution with a rounded LSB.
5. Compute the Calibration Register value using Equation 4:
0.04096
Current_LSB ´ RSHUNT
Cal = trunc
Cal = 4096
(4)
17
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
6. Calculate the Power LSB, using Equation 5. Equation 5 shows a general formula; because the bus voltage
measurement LSB is always 4mV, the power formula reduces to the calculated result.
Power_LSB = 20 Current_LSB
-6
Power_LSB = 400 ´ 10
(5)
7. Compute the maximum current and shunt voltage values (before overflow), as shown by Equation 6 and
Equation 7. Note that both Equation 6 and Equation 7 involve an If - then condition:
Max_Current = Current_LSB ´ 32767
Max_Current = 0.65534
(6)
If Max_Current ≥ Max Possible_I then
Max_Current_Before_Overflow = MaxPossible_I
Else
Max_Current_Before_Overflow = Max_Current
End If
(Note that Max_Current is greater than MaxPossible_I in this example.)
Max_Current_Before_Overflow = 0.64 (Note: This result is displayed by software as seen in Figure 21.)
Max_ShuntVoltage = Max_Current_Before_Overflow ´ RSHUNT
Max_ShuntVoltage = 0.32
(7)
If Max_ShuntVoltage ≥ VSHUNT_MAX
Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX
Else
Max_ShuntVoltage_Before_Overflow= Max_ShuntVoltage
End If
(Note that Max_ShuntVoltage is greater than VSHUNT_MAX in this example.)
Max_ShuntVoltage_Before_Overflow = 0.32 (Note: This result is displayed by software as seen in
Figure 21.)
8. Compute the maximum power with Equation 8.
MaximumPower = Max_Current_Before_Overflow ´ VBUS_MAX
MaximumPower = 20.48
(8)
9. (Optional second Calibration step.) Compute corrected full-scale calibration value based on measured
current.
INA219_Current = 0.63484
MeaShuntCurrent = 0.55
Cal ´ MeasShuntCurrent
Corrected_Full_Scale_Cal = trunc
INA219_Current
Corrected_Full_Scale_Cal = 3548
(9)
18
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
Figure 21 illustrates how to perform the same
procedure discussed in this example using the
automated INA219EVM software. Note that the same
numbers used in the nine-step example are used in
the software example in Figure 21. Also note that
Figure 21 illustrates which results correspond to
which step (for example, the information entered in
Step 1 is enclosed in a box in Figure 21 and labeled).
Step1
Optional
Step9
Equ9
Step2
Equ1
Step3
Step4
Equ2, 3
Step5
Equ4
Step7
Equ6, 7
Step6
Equ4
Step8
Equ8
Figure 21. INA219 Calibration Sofware Automatically Computes Calibration Steps 1-9
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Calibration Example 2 (Overflow Possible)
software. Note that the same numbers used in the
nine-step example are used in the software example
in Figure 22. Also note that Figure 22 illustrates which
results correspond to which step (for example, the
information entered in Step 1 is circled in Figure 22
and labeled).
This design example uses the nine-step procedure for
calibrating the INA219 where overflow is possible.
Figure 22 illustrates how the same procedure is
performed using the automated INA219EVM
1. Establish the following parameters:
VBUS_MAX = 32
VSHUNT_MAX = 0.32
RSHUNT = 5
2. Determine the maximum possible current using Equation 10:
VSHUNT_MAX
MaxPossible_I =
RSHUNT
MaxPossible_I = 0.064
(10)
3. Choose the desired maximum current value: Max_Expected_I, ≤ MaxPossible_I. This value is selected
based on system expectations.
Max_Expected_I = 0.06
4. Calculate the possible range of current LSBs. This calculation is done by first computing a range of LSB's
that is appropriate for the design. Next, select an LSB withing this range. Note that the results will have the
most resolution when the minimum LSB is selected. Typically, an LSB is selected to be the nearest round
number to the minimum LSB.
Max_Expected_I
Minimum_LSB =
32767
-6
Minimum_LSB = 1.831 ´ 10
(11)
Max_Expected_I
Maximum_LSB =
4096
-6
Maximum_LSB = 14.652 ´ 10
(12)
Choose an LSB in the range: Minimum_LSB<Selected_LSB<Maximum_LSB
Current_LSB = 1.9 × 10–6
Note:
This value was selected to be a round number near the Minimum_LSB. This section allows for good
resolution with a rounded LSB.
5. Compute the calibration register using Equation 13:
0.04096
Current_LSB ´ RSHUNT
Cal = trunc
Cal = 4311
(13)
6. Calculate the Power LSB using Equation 14. Equation 14 shows a general formula; because the bus voltage
measurement LSB is always 4mV, the power formula reduces to calculate the result.
Power_LSB = 20 Current_LSB
-6
Power_LSB = 38 ´ 10
(14)
20
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
7. Compute the maximum current and shunt voltage values (before overflow), as shown by Equation 15 and
Equation 16. Note that both Equation 15 and Equation 16 involve an If - then condition.
Max_Current = Current_LSB ´ 32767
Max_Current = 0.06226
(15)
If Max_Current ≥ Max Possible_I then
Max_Current_Before_Overflow = MaxPossible_I
Else
Max_Current_Before_Overflow = Max_Current
End If
(Note that Max_Current is less than MaxPossible_I in this example.)
Max_Current_Before_Overflow = 0.06226 (Note: This result is displayed by software as seen in Figure 22.)
Max_ShuntVoltage = Max_Current_Before_Overflow ´ RSHUNT
Max_ShuntVoltage = 0.3113
(16)
If Max_ShuntVoltage ≥ VSHUNT_MAX
Max_ShuntVoltage_Before_Overflow = VSHUNT_MAX
Else
Max_ShuntVoltage_Before_Overflow= Max_ShuntVoltage
End If
(Note that Max_ShuntVoltage is less than VSHUNT_MAX in this example.)
Max_ShuntVoltage_Before_Overflow = 0.3113 (Note: This result is displayed by software as seen in
Figure 22.)
8. Compute the maximum power with equation 8.
MaximumPower = Max_Current_Before_Overflow ´ VBUS_MAX
MaximumPower = 1.992
(17)
9. (Optional second calibration step.) Compute the corrected full-scale calibration value based on measured
current.
INA219_Current = 0.06226
MeaShuntCurrent = 0.05
Cal ´ MeasShuntCurrent
Corrected_Full_Scale_Cal = trunc
INA219_Current
Corrected_Full_Scale_Cal = 3462
(18)
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Figure 22 illustrates how to perform the same
procedure discussed in this example using the
automated INA219EVM software. Note that the same
numbers used in the nine-step example are used in
the software example in Figure 22.
Also note that Figure 22 illustrates which results
correspond to which step (for example, the
information entered in Step 1 is enclosed in a box in
Figure 22 and labeled).
Step1
Optional
Step9
Equ18
Step2
Equ10
Step3
Step4
Equ11, 12
Step5
Equ13
Step7
Equ15, 16
Step6
Equ14
Step8
Equ17
Figure 22. Calibration Software Automatically Computes Calibration Steps 1-9
22
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
CONFIGURE/MEASURE/CALCULATE
EXAMPLE
shunt voltage. By knowing the value of the shunt
resistor, the device can then calculate the amount of
current that created the measured shunt voltage drop.
The first step when calculating the calibration value is
setting the current LSB. The Calibration Register
value is based on a calculation that has its precision
capability limited by the size of the register and the
Current Register LSB. The device can measure
bidirectional current; thus, the MSB of the Current
Register is a sign bit that allows for the rest of the 15
bits to be used for the Current Register value. It is
common when using the current value calculations to
use a resolution between 12 bits and 15 bits.
Calculating the current LSB for each of these
resolutions provides minimum and maximum values.
These values are calculated assuming the maximum
current that will be expected to flow through the
current shunt resistor, as shown in Equation 2 and
Equation 3. To simplify the mathematics, it is
common to choose a round number located between
these two points. For this example, the maximum
current LSB is 3.66mA/bit and the minimum current
LSB would be 457.78µA/bit assuming a maximum
expected current of 15A. For this example, a value of
1mA/bit was chosen for the current LSB. Setting the
current LSB to this value allows for sufficient
precision while serving to simplify the math as well.
Using Equation 4 results in a Calibration Register
value of 20480, or 5000h.
In this example, the 10A load creates a differential
voltage of 20mV across a 2mΩ shunt resistor. The
voltage present at the VIN– pin is equal to the
common-mode voltage minus the differential drop
across the resistor. The bus voltage for the INA219 is
internally measured at the VIN– pin to measure the
voltage level delivered to the load. For this example,
the voltage at the VIN– pin is 11.98V. For this
particular range (40mV full-scale), this small
difference is not a significant deviation from the 12V
common-mode voltage. However, at larger full-scale
ranges, this deviation can be much larger.
Note that the Bus Voltage Register bits are not
right-aligned. In order to compute the value of the
Bus Voltage Register contents using the LSB of 4mV,
the register must be shifted right by three bits. This
shift puts the BD0 bit in the LSB position so that the
contents can be multiplied by the 4mV LSB value to
compute the bus voltage measured by the device.
The shifted value of the bus voltage register contents
is now equal to BB3h, a decimal equivalent of 2995.
This value of 2995 multiplied by the 4mV LSB results
in a value of 11.98V.
The Calibration Register (05h) is set in order to
provide the device information about the current
shunt resistor that was used to create the measured
+3.3V to +5V
RSHUNT
2mW
10mF
0.1mF
10A
Load
+12V
VCM
VS (Supply Voltage)
SDA
SCK
Power Register
Current Register
Voltage Register
´
I2C
Interface
V
VIN+
VIN-
A0
A1
I
GND
Figure 23. Example Circuit Configuration
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
The Current Register (04h) is then calculated by
multiplying the shunt voltage contents by the
Calibration Register and then dividing by 4096. For
this example, the shunt voltage of 2000 is multiplied
by the calibration register of 20480 and then divided
by 4096 to yield a Current Register of 2710h.
this result by the power LSB that is 20 times the
1 × 10-3 current LSB, or 20 × 10-3, results in a power
calculation of 5990
× 20mW/bit, which equals
119.8W. This result matches what is expected for this
register. A manual calculation for the power being
delivered to the load would use 11.98V (12VCM –
20mV shunt drop) multiplied by the load current of
10A to give a 119.8W result.
The Power Register (03h) is then be calculated by
multiplying the Current Register of 10000 by the Bus
Voltage Register of 2995 and then dividing by 5000.
For this example, the Power Register contents are
1766h, or a decimal equivalent of 5990. Multiplying
Table 3 shows the steps for configuring, measuring,
and calculating the values for current and power for
this device.
Table 3. Configure/Measure/Calculate Example(1)
STEP #
Step 1
Step 2
Step 3
Step 4
Step 5
Step 6
REGISTER NAME
Configuration
Shunt
ADDRESS
00h
CONTENTS
019Fh
ADJ
DEC
LSB
VALUE
01h
07D0h
5D98h
5000h
2000
2995
10µV
20mV
Bus
02h
0BB3
4mV
11.98V
Calibration
Current
05h
20480
10000
5990
04h
2710h
1mA
10.0A
Power
03h
1766h
20mW
119.8W
(1) Conditions: load = 10A, VCM = 12V, RSHUNT = 2mΩ, VSHUNT FSR = 40mV, and VBUS = 16V.
24
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
REGISTER INFORMATION
The INA219 uses a bank of registers for holding
configuration settings, measurement results,
maximum/minimum limits, and status information.
Table 4 summarizes the INA219 registers; Figure 12
illustrates registers.
Register contents are updated 4μs after completion of
the write command. Therefore, a 4μs delay is
required between completion of a write to a given
register and a subsequent read of that register
(without changing the pointer) when using SCL
frequencies in excess of 1MHz.
Table 4. Summary of Register Set
POINTER
ADDRESS
POWER-ON RESET
HEX
REGISTER NAME
FUNCTION
BINARY
HEX
TYPE(1)
All-register reset, settings for bus
voltage range, PGA Gain, ADC
resolution/averaging.
00
Configuration Register
00111001 10011111
399F
R/W
01
02
03
Shunt Voltage
Bus Voltage
Power(2)
Shunt voltage measurement data.
Bus voltage measurement data.
Power measurement data.
Shunt voltage
Bus voltage
—
—
R
R
R
00000000 00000000
0000
Contains the value of the current flowing
through the shunt resistor.
04
Current(2)
00000000 00000000
0000
R
Sets full-scale range and LSB of current
and power measurements. Overall
system calibration.
05
Calibration
00000000 00000000
0000
R/W
(1) Type: R = Read-Only, R/W = Read/Write.
(2) The Power Register and Current Register default to '0' because the Calibration Register defaults to '0', yielding a zero current value until
the Calibration Register is programmed.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
REGISTER DETAILS
All INA219 registers 16-bit registers are actually two 8-bit bytes via the I2C interface.
Configuration Register 00h (Read/Write)
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
RST
—
BRNG
PG1
PG0
BADC4
BADC3
BADC2
BADC1
SADC4
SADC3
SADC2
SADC1 MODE3 MODE2 MODE1
POR
VALUE
0
0
1
1
1
0
0
1
1
0
0
1
1
1
1
1
Bit Descriptions
RST:
Reset Bit
Bit 15
Setting this bit to '1' generates a system reset that is the same as power-on reset. Resets all registers to default
values; this bit self-clears.
BRNG:
Bus Voltage Range
Bit 13
0 = 16V FSR
1 = 32V FSR (default value)
PG:
PGA (Shunt Voltage Only)
Bits 11, 12
Sets PGA gain and range. Note that the PGA defaults to ÷8 (320mV range). Table 5 shows the gain and range for
the various product gain settings.
Table 5. PG Bit Settings(1)
PG1
PG0
GAIN
1
RANGE
±40mV
0
0
1
1
0
1
0
1
÷2
±80mV
÷4
±160mV
±320mV
÷8
(1) Shaded values are default.
BADC:
BADC Bus ADC Resolution/Averaging
Bits 7–10
These bits adjust the Bus ADC resolution (9-, 10-, 11-, or 12-bit) or set the number of samples used when
averaging results for the Bus Voltage Register (02h).
26
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
SADC:
SADC Shunt ADC Resolution/Averaging
Bits 3–6
These bits adjust the Shunt ADC resolution (9-, 10-, 11-, or 12-bit) or set the number of samples used when
averaging results for the Shunt Voltage Register (01h).
BADC (Bus) and SADC (Shunt) ADC resolution/averaging and conversion time settings are shown in Table 6.
Table 6. ADC Settings(1)
ADC4
ADC3
ADC2
ADC1
MODE/SAMPLES
CONVERSION TIME
84μs
0
0
0
0
1
1
1
1
1
1
1
1
X(2)
X(2)
X(2)
X(2)
0
0
0
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
0
1
0
1
9-bit
10-bit
11-bit
12-bit
12-bit
2
148μs
276μs
532μs
532μs
0
1.06ms
0
4
2.13ms
0
8
4.26ms
1
16
8.51ms
1
32
17.02ms
34.05ms
68.10ms
1
64
1
128
(1) Shaded values are default.
(2) X = Don't care.
MODE:
Operating Mode
Bits 0–2
Selects continuous, triggered, or power-down mode of operation. These bits default to continuous shunt and bus
measurement mode. The mode settings are shown in Table 7.
Table 7. Mode Settings(1)
MODE3
MODE2
MODE1
MODE
0
0
0
0
1
1
1
1
0
0
1
1
0
0
1
1
0
1
0
1
0
1
0
1
Power-Down
Shunt Voltage, Triggered
Bus Voltage, Triggered
Shunt and Bus, Triggered
ADC Off (disabled)
Shunt Voltage, Continuous
Bus Voltage, Continuous
Shunt and Bus, Continuous
(1) Shaded values are default.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
DATA OUTPUT REGISTERS
www.ti.com
Shunt Voltage Register 01h (Read-Only)
The Shunt Voltage Register stores the current shunt voltage reading, VSHUNT. Shunt Voltage Register bits are
shifted according to the PGA setting selected in the Configuration Register (00h). When multiple sign bits are
present, they will all be the same value. Negative numbers are represented in two's complement format.
Generate the two's complement of a negative number by complementing the absolute value binary number and
adding 1. Extend the sign, denoting a negative number by setting the MSB = '1'. Extend the sign to any
additional sign bits to form the 16-bit word.
Example: For a value of VSHUNT = –320mV:
1. Take the absolute value (include accuracy to 0.01mV)==> 320.00
2. Translate this number to a whole decimal number ==> 32000
3. Convert it to binary==> 111 1101 0000 0000
4. Complement the binary result : 000 0010 1111 1111
5. Add 1 to the Complement to create the Two’s Complement formatted result ==> 000 0011 0000 0000
6. Extend the sign and create the 16-bit word: 1000 0011 0000 0000 = 8300h (Remember to extend the sign to
all sign-bits, as necessary based on the PGA setting.)
At PGA = ÷8, full-scale range = ±320mV (decimal = 32000, positive value hex = 7D00, negative value hex =
8300), and LSB = 10μV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
SIGN
SD14_8 SD13_8 SD12_8 SD11_8 SD10_8
SD9_8
SD8_8
SD7_8
SD6_8
SD5_8
SD4_8
SD3_8
SD2_8
SD1_8
SD0_8
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
At PGA = ÷4, full-scale range = ±160mV (decimal = 16000, positive value hex = 3E80, negative value hex =
C180), and LSB = 10μV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
SIGN
SIGN
SD13_4 SD12_4 SD11_4 SD10_4
SD9_4
SD8_4
SD7_4
SD6_4
SD5_4
SD4_4
SD3_4
SD2_4
SD1_4
SD0_4
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
At PGA = ÷2, full-scale range = ±80mV (decimal = 8000, positive value hex = 1F40, negative value hex = E0C0),
and LSB = 10μV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
SIGN
SIGN
SIGN
SD12_2 SD11_2 SD10_2
SD9_2
SD8_2
SD7_2
SD6_2
SD5_2
SD4_2
SD3_2
SD2_2
SD1_2
SD0_2
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
At PGA = ÷1, full-scale range = ±40mV (decimal = 4000, positive value hex = 0FA0, negative value hex = F060),
and LSB = 10μV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
SIGN
SIGN
SIGN
SIGN
SD11_1 SD10_1
SD9_1
SD8_1
SD7_1
SD6_1
SD5_1
SD4_1
SD3_1
SD2_1
SD1_1
SD0_1
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
28
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
Table 8. Shunt Voltage Register Format(1)
VSHUNT
Reading (mV)
Decimal
Value
PGA = ÷ 8
(D15…..................D0)
PGA = ÷ 4
(D15…..................D0)
PGA = ÷ 2
(D15…..................D0)
PGA = ÷ 1
(D15…..................D0)
320.02
320.01
320.00
319.99
319.98
32002
32001
32000
31999
31998
0111 1101 0000 0000
0111 1101 0000 0000
0111 1101 0000 0000
0111 1100 1111 1111
0111 1100 1111 1110
0011 1110 1000 0000
0011 1110 1000 0000
0011 1110 1000 0000
0011 1110 1000 0000
0011 1110 1000 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
160.02
160.01
160.00
159.99
159.98
16002
16001
16000
15999
15998
0011 1110 1000 0010
0011 1110 1000 0001
0011 1110 1000 0000
0011 1110 0111 1111
0011 1110 0111 1110
0011 1110 1000 0000
0011 1110 1000 0000
0011 1110 1000 0000
0011 1110 0111 1111
0011 1110 0111 1110
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
80.02
80.01
80.00
79.99
79.98
8002
8001
8000
7999
7998
0001 1111 0100 0010
0001 1111 0100 0001
0001 1111 0100 0000
0001 1111 0011 1111
0001 1111 0011 1110
0001 1111 0100 0010
0001 1111 0100 0001
0001 1111 0100 0000
0001 1111 0011 1111
0001 1111 0011 1110
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0100 0000
0001 1111 0011 1111
0001 1111 0011 1110
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
40.02
40.01
40.00
39.99
39.98
4002
4001
4000
3999
3998
0000 1111 1010 0010
0000 1111 1010 0001
0000 1111 1010 0000
0000 1111 1001 1111
0000 1111 1001 1110
0000 1111 1010 0010
0000 1111 1010 0001
0000 1111 1010 0000
0000 1111 1001 1111
0000 1111 1001 1110
0000 1111 1010 0010
0000 1111 1010 0001
0000 1111 1010 0000
0000 1111 1001 1111
0000 1111 1001 1110
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1010 0000
0000 1111 1001 1111
0000 1111 1001 1110
0.02
0.01
0
2
1
0000 0000 0000 0010
0000 0000 0000 0001
0000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1110
0000 0000 0000 0010
0000 0000 0000 0001
0000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1110
0000 0000 0000 0010
0000 0000 0000 0001
0000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1110
0000 0000 0000 0010
0000 0000 0000 0001
0000 0000 0000 0000
1111 1111 1111 1111
1111 1111 1111 1110
0
–0.01
–0.02
–1
–2
–39.98
–39.99
–40.00
–40.01
–40.02
–3998
–3999
–4000
–4001
–4002
1111 0000 0110 0010
1111 0000 0110 0001
1111 0000 0110 0000
1111 0000 0101 1111
1111 0000 0101 1110
1111 0000 0110 0010
1111 0000 0110 0001
1111 0000 0110 0000
1111 0000 0101 1111
1111 0000 0101 1110
1111 0000 0110 0010
1111 0000 0110 0001
1111 0000 0110 0000
1111 0000 0101 1111
1111 0000 0101 1110
1111 0000 0110 0010
1111 0000 0110 0001
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
–79.98
–79.99
–80.00
–80.01
–80.02
–7998
–7999
–8000
–8001
–8002
1110 0000 1100 0010
1110 0000 1100 0001
1110 0000 1100 0000
1110 0000 1011 1111
1110 0000 1011 1110
1110 0000 1100 0010
1110 0000 1100 0001
1110 0000 1100 0000
1110 0000 1011 1111
1110 0000 1011 1110
1110 0000 1100 0010
1110 0000 1100 0001
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
–159.98
–159.99
–160.00
–160.01
–160.02
–15998
–15999
–16000
–16001
–16002
1100 0001 1000 0010
1100 0001 1000 0001
1100 0001 1000 0000
1100 0001 0111 1111
1100 0001 0111 1110
1100 0001 1000 0010
1100 0001 1000 0001
1100 0001 1000 0000
1100 0001 1000 0000
1100 0001 1000 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
–319.98
–319.99
–320.00
–320.01
–320.02
–31998
–31999
–32000
–32001
–32002
1000 0011 0000 0010
1000 0011 0000 0001
1000 0011 0000 0000
1000 0011 0000 0000
1000 0011 0000 0000
1100 0001 1000 0000
1100 0001 1000 0000
1100 0001 1000 0000
1100 0001 1000 0000
1100 0001 1000 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1110 0000 1100 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
1111 0000 0110 0000
(1) Out-of-range values are shown in grey shading.
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Link(s): INA219
INA219
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
www.ti.com
Bus Voltage Register 02h (Read-Only)
The Bus Voltage Register stores the most recent bus voltage reading, VBUS
.
At full-scale range = 32V (decimal = 8000, hex = 1F40), and LSB = 4mV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
BD12
BD11
BD10
BD9
BD8
BD7
BD6
BD5
BD4
BD3
BD2
0
BD1
BD0
—
CNVR
0
OVF
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
At full-scale range = 16V (decimal = 4000, hex = 0FA0), and LSB = 4mV.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
0
BD11
BD10
BD9
BD8
BD7
BD6
BD5
BD4
BD3
BD2
BD1
BD0
—
CNVR
OVF
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
CNVR:
Conversion Ready
Bit 1
Although the data from the last conversion can be read at any time, the INA219 Conversion Ready bit (CNVR)
indicates when data from a conversion is available in the data output registers. The CNVR bit is set after all
conversions, averaging, and multiplications are complete. CNVR will clear under the following conditions:
1.) Writing a new mode into the Operating Mode bits in the Configuration Register (except for Power-Down or
Disable)
2.) Reading the Power Register
OVF:
Math Overflow Flag
Bit 0
The Math Overflow Flag (OVF) is set when the Power or Current calculations are out of range. It indicates that
current and power data may be meaningless.
Power Register 03h (Read-Only)
Full-scale range and LSB are set by the Calibration Register. See the Programming the INA219 Power
Measurement Engine section.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
PD15
PD14
PD13
PD12
PD11
PD10
PD9
PD8
PD7
PD6
PD5
PD4
PD3
PD2
PD1
PD0
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
The Power Register records power in watts by multiplying the values of the current with the value of the bus
voltage according to the equation:
Current ´ BusVoltage
Power =
5000
Current Register 04h (Read-Only)
Full-scale range and LSB depend on the value entered in the Calibration Register. See the Programming the
INA219 Power Measurement Engine section. Negative values are stored in two's complement format.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0
BIT
NAME
CSIGN
CD14
CD13
CD12
CD11
CD10
CD9
CD8
CD7
CD6
CD5
CD4
CD3
CD2
CD1
CD0
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
The value of the Current Register is calculated by multiplying the value in the Shunt Voltage Register with the
value in the Calibration Register according to the equation:
ShuntVoltage ´ Calibration Register
Current =
4096
30
Submit Documentation Feedback
Copyright © 2008–2011, Texas Instruments Incorporated
Product Folder Link(s): INA219
INA219
www.ti.com
SBOS448F –AUGUST 2008–REVISED SEPTEMBER 2011
CALIBRATION REGISTER
Calibration Register 05h (Read/Write)
Current and power calibration are set by bits D15 to D1 of the Calibration Register. Note that bit D0 is not used in
the calculation. This register sets the current that corresponds to a full-scale drop across the shunt. Full-scale
range and the LSB of the current and power measurement depend on the value entered in this register. See the
Programming the INA219 Power Measurement Engine section. This register is suitable for use in overall system
calibration. Note that the '0' POR values are all default.
BIT #
D15
D14
D13
D12
D11
D10
D9
D8
D7
D6
D5
D4
D3
D2
D1
D0(1)
BIT
NAME
FS15
FS14
FS13
FS12
FS11
FS10
FS9
FS8
FS7
FS6
FS5
FS4
FS3
FS2
FS1
FS0
POR
VALUE
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
0
(1) D0 is a void bit and will always be '0'. It is not possible to write a '1' to D0. CALIBRATION is the value stored in D15:D1.
space
REVISION HISTORY
NOTE: Page numbers for previous revisions may differ from page numbers in the current version.
Changes from Revision E (September 2010) to Revision F
Page
•
•
Changed values in text. ...................................................................................................................................................... 24
Changed step 5 and step 6 values in Table 3 .................................................................................................................... 24
Changes from Revision D (September 2010) to Revision E
Page
•
Updated Packaging Information table ................................................................................................................................... 2
Copyright © 2008–2011, Texas Instruments Incorporated
Submit Documentation Feedback
31
Product Folder Link(s): INA219
PACKAGE OPTION ADDENDUM
www.ti.com
19-Apr-2013
PACKAGING INFORMATION
Orderable Device
INA219AID
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-25 to 85
Top-Side Markings
Samples
Drawing
Qty
(1)
(2)
(3)
(4)
ACTIVE
SOIC
SOT-23
SOT-23
SOT-23
SOT-23
SOIC
D
8
8
8
8
8
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-1-260C-UNLIM
I219A
INA219AIDCNR
INA219AIDCNRG4
INA219AIDCNT
INA219AIDCNTG4
INA219AIDR
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
DCN
DCN
DCN
DCN
D
3000
3000
250
Green (RoHS
& no Sb/Br)
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
-40 to 125
A219
A219
A219
A219
I219A
I219B
B219
B219
I219B
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
250
Green (RoHS
& no Sb/Br)
2500
75
Green (RoHS
& no Sb/Br)
INA219BID
SOIC
D
Green (RoHS
& no Sb/Br)
INA219BIDCNR
INA219BIDCNT
INA219BIDR
SOT-23
SOT-23
SOIC
DCN
DCN
D
3000
250
Green (RoHS
& no Sb/Br)
Green (RoHS
& no Sb/Br)
2500
Green (RoHS
& no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
19-Apr-2013
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4)
Multiple Top-Side Markings will be inside parentheses. Only one Top-Side Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a
continuation of the previous line and the two combined represent the entire Top-Side Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Sep-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
INA219AIDCNR
INA219AIDCNT
INA219BIDCNR
INA219BIDCNT
SOT-23
SOT-23
SOT-23
SOT-23
DCN
DCN
DCN
DCN
8
8
8
8
3000
250
179.0
179.0
179.0
179.0
8.4
8.4
8.4
8.4
3.2
3.2
3.2
3.2
3.2
3.2
3.2
3.2
1.4
1.4
1.4
1.4
4.0
4.0
4.0
4.0
8.0
8.0
8.0
8.0
Q3
Q3
Q3
Q3
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Sep-2011
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
INA219AIDCNR
INA219AIDCNT
INA219BIDCNR
INA219BIDCNT
SOT-23
SOT-23
SOT-23
SOT-23
DCN
DCN
DCN
DCN
8
8
8
8
3000
250
195.0
195.0
195.0
195.0
200.0
200.0
200.0
200.0
45.0
45.0
45.0
45.0
3000
250
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
HPA01025YZFT
1-CHANNEL POWER SUPPLY MANAGEMENT CKT, BGA15, 2.61 X 1.956 MM, 0.5 MM PITCH, GREEN, DSBGA-15
TI
HPA01061DTR-4
1A SWITCHING CONTROLLER, 52kHz SWITCHING FREQ-MAX, PDSO8, GREEN, PLASTIC, MS-012AA, SOIC-8
TI
HPA02205RSER
High-Speed USB 2.0 (480 Mbps) 1:2 Multiplexer/Demultiplexer Switch With Single Enable 10-UQFN -40 to 85
TI
HPA02206RSWR
High-Speed USB 2.0 (480-Mbps) 1:2 Multiplexer/Demultiplexer Switch With Single 10-UQFN -40 to 85
TI
©2020 ICPDF网 联系我们和版权申明