ISO721-Q1 [TI]
3.3-V / 5-V HIGH-SPEED DIGITAL ISOLATORS; 3.3 V / 5 V高速数字隔离器
| 型号： | ISO721-Q1 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 3.3-V / 5-V HIGH-SPEED DIGITAL ISOLATORS |
| 文件： | 总19页 (文件大小：379K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
3.3-V / 5-V HIGH-SPEED DIGITAL ISOLATORS
1
FEATURES
•
Qualified for Automotive Applications
•
•
•
•
•
Low-Power Sleep Mode
High Electromagnetic Immunity
Low Input Current Requirement
Failsafe Output
•
4000-V(peak) Isolation
–
–
UL 1577, IEC 60747-5-2 (VDE 0884, Rev 2),
IEC 61010-1
50-kV/s Transient Immunity (Typ)
Drop-In Replacement for Most Optical and
Magnetic Isolators
•
Signaling Rate 0 Mbps to 150 Mbps
–
–
Low Propagation Delay
Low Pulse Skew
(Pulse-Width Distortion)
DESCRIPTION
The ISO721 is a digital isolator with a logic input and output buffer separated by a silicon oxide (SiO2) insulation
barrier. This barrier provides galvanic isolation of up to 4000 V. Used in conjunction with isolated power supplies,
this device prevents noise currents on a data bus or other circuits from entering the local ground, and interfering
with or damaging sensitive circuitry.
A binary input signal is conditioned, translated to a balanced signal, then differentiated by the capacitive isolation
barrier. Across the isolation barrier, a differential comparator receives the logic transition information, then sets or
resets a flip-flop and the output circuit accordingly. A periodic update pulse is sent across the barrier to ensure
the proper dc level of the output. If this dc refresh pulse is not received for more than 4 µs, the input is assumed
to be unpowered or not being actively driven, and the failsafe circuit drives the output to a logic high state.
FUNCTION DIAGRAM
Isolation Barrier
DC Channel
+
_
Filter
Pulse Width
Demodulation
OSC
+
PWM
V
ref
_
+
Carrier Detect
POR
POR
BIAS
+
_
Data MUX
AC Detect
3-State
Input
+
Filter
IN
V
ref
_
+
OUT
Output Buffer
AC Channel
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2008, Texas Instruments Incorporated
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
DESCRIPTION (CONTINUED)
The symmetry of the dielectric and capacitor within the integrated circuitry provides for close capacitive matching
and allows fast transient voltage changes between the input and output grounds without corrupting the output.
The small capacitance and resulting time constant provide for fast operation with signaling rates(1) from 0 Mbps
(dc) to 100 Mbps.
The device requires two supply voltages of 3.3 V, 5 V, or any combination. All inputs are 5-V tolerant when
supplied from a 3.3-V supply, and all outputs are 4-mA CMOS. The device has a TTL input threshold and a
noise-filter at the input that prevents transient pulses of up to 2 ns in duration from being passed to the output of
the device.
The ISO721 is characterized for operation over the ambient temperature range of –40°C to 125°C.
(1) The signaling rate of a line is the number of voltage transitions that are made per second expressed in
the units bps (bits per second).
D PACKAGE
(TOP VIEW)
V
V
V
CC2
1
2
3
4
8
7
6
5
CC1
IN
GND2
OUT
CC1
GND1
GND2
ORDERING INFORMATION(1)
TA
PACKAGE(2)
ORDERABLE PART NUMBER
ISO721QDRQ1
TOP-SIDE MARKING
IS721Q
–40°C to 125°C
SOIC – D
Reel of 2500
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
REGULATORY INFORMATION
VDE
CSA
UL
Approved under CSA Component
Acceptance Notice: CA-5A
Recognized under 1577
Certified according to IEC 60747-5-2
File Number: 40016131
Component Recognition Program(1)
File Number: 1698195
File Number: E181974
(1) Production tested ≥ 3000 VRMS for 1 second in accordance with UL 1577.
2
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
ABSOLUTE MAXIMUM RATINGS(1)
VCC
VI
Supply voltage(2), VCC1, VCC2
Voltage at IN or OUT terminal
Output current
–0.5 V to 6 V
–0.5 V to 6 V
±15 mA
IO
TJ
Maximum virtual-junction temperature
170°C
Human-Body Model(3)
Charged-Device Model(4)
±2 kV
ESD
Electrostatic discharge rating
±1 kV
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltage values except differential I/O bus voltages are with respect to network ground terminal and are peak voltage values. Vrms
values are not listed in this publication.
(3) JEDEC Standard 22, Test Method A114-C.01
(4) JEDEC Standard 22, Test Method C101
RECOMMENDED OPERATING CONDITIONS
MIN
MAX UNIT
VCC
IOH
IOL
tui
Supply voltage(1), VCC1, VCC2
High-level output current
3
5.5
4
V
mA
mA
ns
V
Low-level output current
–4
10
2
Input pulse width
VIH
VIL
TA
TJ
High-level input voltage (IN)
Low-level input voltage (IN)
Operating free-air temperature
Operating virtual-junction temperature
VCC
0.8
0
V
–40
125
150
°C
°C
See the Thermal Characteristics table
H
External magnetic field intensity per IEC 61000-4-8 and IEC 61000-4-9 certification
1000 A/m
(1) For 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For 3.3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
IEC 60747-5-2 INSULATION CHARACTERISTICS(1)
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SPECIFICATIONS
UNIT
VIORM
Maximum working insulation voltage
560
V
After Input/Output Safety Test Subgroup 2/3
VPR = VIORM × 1.2, t = 10 s,
Partial discharge < 5 pC
672
896
V
V
V
Method a, VPR = VIORM × 1.6,
Type and sample test with t = 10 s,
Partial discharge < 5 pC
VPR
Input to output test voltage
Method b1, VPR = VIORM × 1.875,
100 % Production test with t = 1 s,
Partial discharge < 5 pC
1050
VIOTM
RS
Transient overvoltage
Insulation resistance
Pollution degree
t = 60 s
4000
>109
2
V
VIO = 500 V at TS
Ω
(1) Climatic Classification 40/125/21
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VCC1 and VCC2 5-V(1) OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.5
2
MAX UNIT
Quiescent
25 Mbps
Quiescent
25 Mbps
1
ICC1
ICC2
VOH
VOL
VCC1 supply current
VI = VCC or 0 V, No load
mA
4
8
12
VCC2 supply current
VI = VCC or 0 V, No load
mA
14
10
4.6
5
IOH = -4 mA, See Figure 1
IOH = –20 µA, See Figure 1
IOL = 4 mA, See Figure 1
IOL = 20 µA, See Figure 1
VCC – 0.8
VCC – 0.1
High-level output voltage
Low-level output voltage
V
0.2
0
0.4
V
0.1
VI(HYS)
IIH
Input voltage hysteresis
High-level input current
Low-level input current
Input capacitance to ground
150
mV
IN at 2 V
10
µA
IIL
IN at 0.8 V
–10
15
CI
IN at VCC, VI = 0.4 sin (4E6πt)
VI = VCC or 0 V, See Figure 3
1
pF
CMTI
Common-mode transient immunity
50
kV/µs
(1) For 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For 3.3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS: VCC1 and VCC2 5-V OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
See Figure 1
MIN
TYP
17
17
0.5
0
MAX UNIT
tPLH
tPHL
tsk(p)
tsk(pp)
tr
Propagation delay, low-to-high-level output
Propagation delay , high-to-low-level output
24
24
2
ns
ns
ns
ns
ns
ns
µs
See Figure 1
See Figure 1
Pulse skew |tPHL – tPLH
|
(1)
Part-to-part skew
3
Output signal rise time
Output signal fall time
See Figure 1
See Figure 1
See Figure 2
1
tf
1
tfs
Failsafe output delay time from input power loss
3
100-Mbps NRZ data input,
See Figure 4
2
3
tjit(PP)
Peak-to-peak eye-pattern jitter
ns
100-Mbps unrestricted bit run length
data input, See Figure 4
(1) tsk(PP) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
4
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
ELECTRICAL CHARACTERISTICS: VCC1 at 5-V, VCC2 at 3.3-V(1) OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.5
2
MAX UNIT
Quiescent
25 Mbps
Quiescent
25 Mbps
1
ICC1
ICC2
VOH
VOL
VCC1 supply current
VI = VCC or 0 V, No load
mA
4
4
6.5
mA
7.5
VCC2 supply current
VI = VCC or 0 V, No load
5
IOH = –4 mA, See Figure 1
IOH = –20 µA, See Figure 1
IOL = 4 mA, See Figure 1
IOL = 20 µA, See Figure 1
VCC – 0.4
VCC – 0.1
3
High-level output voltage
Low-level output voltage
V
3.3
0.2
0
0.4
V
0.1
VI(HYS)
IIH
Input voltage hysteresis
High-level input current
Low-level input current
Input capacitance to ground
150
mV
IN at 2 V
10
µA
µA
IIL
IN at 0.8 V
–10
15
CI
IN at VCC, VI = 0.4 sin (4E6πt)
VI = VCC or 0 V, See Figure 3
1
pF
CMTI
Common-mode transient immunity
40
kV/µs
(1) For 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For 3.3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS: VCC1 at 5-V, VCC2 at 3.3-V OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
See Figure 1
MIN
TYP
19
19
0.5
0
MAX UNIT
tPLH
tPHL
tsk(p)
tsk(pp)
tr
Propagation delay, low-to-high-level output
Propagation delay , high-to-low-level output
30
30
3
ns
ns
ns
ns
ns
ns
µs
See Figure 1
See Figure 1
Pulse skew |tPHL – tPLH
|
(1)
Part-to-part skew
5
Output signal rise time
Output signal fall time
See Figure 1
See Figure 1
See Figure 2
2
tf
2
tfs
Failsafe output delay time from input power loss
3
100-Mbps NRZ data input,
See Figure 4
2
3
tjit(PP)
Peak-to-peak eye-pattern jitter
ns
100-Mbps unrestricted bit run length
data input, See Figure 4
(1) tsk(PP) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS: VCC1 at 3.3-V, VCC2 at 5-V(1) OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.3
1
MAX UNIT
Quiescent
25 Mbps
Quiescent
25 Mbps
0.5
mA
2
ICC1
ICC2
VOH
VOL
VCC1 supply current
VI = VCC or 0 V, No load
8
12
VCC2 supply current
VI = VCC or 0 V, No load
mA
14
10
4.6
5
IOH = –4 mA, See Figure 1
IOH = –20 µA, See Figure 1
IOL = 4 mA, See Figure 1
IOL = 20 µA, See Figure 1
VCC – 0.8
VCC – 0.1
High-level output voltage
Low-level output voltage
V
0.2
0
0.4
V
0.1
VI(HYS)
IIH
Input voltage hysteresis
High-level input current
Low-level input current
Input capacitance to ground
150
mV
IN at 2 V
10
µA
µA
IIL
IN at 0.8 V
–10
15
CI
IN at VCC, VI = 0.4 sin (4E6πt)
VI = VCC or 0 V, See Figure 3
1
pF
CMTI
Common-mode transient immunity
40
kV/µs
(1) For 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For 3.3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS: VCC1 at 3.3-V, VCC2 at 5-V OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
See Figure 1
MIN
TYP
17
17
0.5
0
MAX UNIT
tPLH
tPHL
tsk(p)
tsk(pp)
tr
Propagation delay, low-to-high-level output
Propagation delay , high-to-low-level output
30
30
3
ns
ns
ns
ns
ns
ns
µs
See Figure 1
See Figure 1
Pulse skew |tPHL – tPLH
|
(1)
Part-to-part skew
5
Output signal rise time
Output signal fall time
See Figure 1
See Figure 1
See Figure 2
1
tf
1
tfs
Failsafe output delay time from input power loss
3
100-Mbps NRZ data input, See
Figure 4
2
3
tjit(PP)
Peak-to-peak eye-pattern jitter
ns
100-Mbps unrestricted bit run length
data input, See Figure 4
(1) tsk(PP) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
6
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
ELECTRICAL CHARACTERISTICS: VCC1 and VCC2 at 3.3-V(1) OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
0.3
1
MAX UNIT
Quiescent
25 Mbps
Quiescent
25 Mbps
0.5
mA
2
ICC1
ICC2
VOH
VOL
VCC1 supply current
VI = VCC or 0 V, No load
4
6.5
mA
7.5
VCC2 supply current
VI = VCC or 0 V, No load
5
IOH = –4 mA, See Figure 1
IOH = –20 µA, See Figure 1
IOL = 4 mA, See Figure 1
IOL = 20 µA, See Figure 1
VCC – 0.4
VCC – 0.1
3
High-level output voltage
Low-level output voltage
V
3.3
0.2
0
0.4
V
0.1
VI(HYS)
IIH
Input voltage hysteresis
High-level input current
Low-level input current
Input capacitance to ground
150
mV
IN at 2 V
10
µA
µA
IIL
IN at 0.8 V
–10
15
CI
IN at VCC, VI = 0.4 sin (4E6πt)
VI = VCC or 0 V, See Figure 3
1
pF
CMTI
Common-mode transient immunity
40
kV/µs
(1) For 5-V operation, VCC1 or VCC2 is specified from 4.5 V to 5.5 V. For 3.3-V operation, VCC1 or VCC2 is specified from 3 V to 3.6 V.
SWITCHING CHARACTERISTICS: VCC1 and VCC2 at 3.3-V OPERATION
over recommended operating conditions (unless otherwise noted)
PARAMETER
TEST CONDITIONS
See Figure 1
MIN
TYP
20
20
0.5
0
MAX UNIT
tPLH
tPHL
tsk(p)
tsk(pp)
tr
Propagation delay, low-to-high-level output
Propagation delay , high-to-low-level output
34
34
3
ns
ns
ns
ns
ns
ns
µs
See Figure 1
See Figure 1
Pulse skew |tPHL – tPLH
|
(1)
Part-to-part skew
5
Output signal rise time
Output signal fall time
See Figure 1
See Figure 1
See Figure 2
2
tf
2
tfs
Failsafe output delay time from input power loss
3
100-Mbps NRZ data input, See
Figure 4
2
3
tjit(PP)
Peak-to-peak eye-pattern jitter
ns
100-Mbps unrestricted bit run length
data input, See Figure 4
(1) tsk(PP) is the magnitude of the difference in propagation delay times between any specified terminals of two devices when both devices
operate with the same supply voltages, at the same temperature, and have identical packages and test circuits.
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
PARAMETER MEASUREMENT INFORMATION
V
CC1
V
V
/2
CC1
V
/2
I
I
OUT
CC1
O
IN
0 V
t
t
PHL
V
PLH
Input
Generator
(see Note A)
V
O
OH
C
90%
10%
V
L
I
50 W
V
50%
50%
O
(see Note B)
V
OL
t
t
f
r
A. The input pulse is supplied by a generator having the following characteristics:
PRR ≤ 50 kHz, 50% duty cycle, tr ≤ 3 ns, tf ≤ 3 ns, ZO = 50 Ω.
B. CL = 15 pF and includes instrumentation and fixture capacitance within ±20%.
Figure 1. Switching Characteristic Test Circuit and Voltage Waveforms
V
I
V
CC1
V
CC1
V
2.7 V
I
IN
0 V
OUT
V
0 V
t
fs
O
V
V
OH
50%
V
O
C
L
OL
15 pF
±20%
NOTE: VI transition time is 100 ns
Figure 2. Failsafe Delay Time Test Circuit and Voltage Waveforms
V
V
CC2
CC1
OUT
C
IN
V
L
CC
V
15 pF
±20%
O
or
0 V
C = 0.1 mF,
I
GND1
GND2
±1%
V
CM
NOTE: Pass/fail criteria is no change in VO.
Figure 3. Common-Mode Transient Immunity Test Circuit and Voltage Waveform
8
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
PARAMETER MEASUREMENT INFORMATION (continued)
Tektronix
Tektronix
HFS9009
784D
PATTERN
GENERATOR
V
CC1
In p u t
0 V
O u tp u t
V
CC2/2
J itte r
NOTE: Bit pattern run length is 216 – 1. Transition Time is 800 ps. NRZ data input has no more than five consecutive
1s or 0s.
Figure 4. Peak-to-Peak Eye-Pattern Jitter Test Circuit and Voltage Waveform
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
DEVICE INFORMATION
PACKAGE CHARACTERISTICS
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
(1)
L(101)
L(102)
Minimum air gap (clearance)
Shortest terminal-to-terminal distance through air
4.8
mm
Shortest terminal to terminal distance across the
package surface
Minimum external tracking (creepage)
4.3
≥ 175
0.008
mm
V
Tracking resistance (comparative
tracking index)
CTI
DIN IEC 60112/VDE 0303 Part 1
Distance through insulation
Minimum internal gap
(internal clearance)
mm
Input to output, VIO = 500 V, all pins on each side of
the barrier tied together creating a two-terminal
device, TA < 100°C
>1012
>1011
Ω
Ω
RIO
Isolation resistance
Input to output, VIO = 500 V,
100°C ≤ TA< TA max.
CIO
CI
Barrier capacitance, input to output
Input capacitance to ground
VI = 0.4 sin (4E6πt)
VI = 0.4 sin (4E6πt)
1
1
pF
pF
(1) Creepage and clearance requirements are applied according to the specific equipment isolation standards of an application. Care should
be taken to maintain the creepage and clearance distance of a board design to ensure that the mounting pads of the isolator on the
printed circuit board do not reduce this distance.
Creepage and clearance on a printed circuit board become equal according to the measurement techniques shown in the Isolation
Glossary. Techniques such as inserting grooves and/or ribs on a printed circuit board are used to help increase these specifications.
IEC 60664-1 RATINGS TABLE
PARAMETER
Basic isolation group
TEST CONDITIONS
SPECIFICATION
Material group
IIIa
I-IV
I-III
Rated mains voltage ≤150 VRMS
Rated mains voltage ≤300 VRMS
Installation classification
DEVICE I/O SCHEMATIC
Equivalent Input and Output Schematic Diagrams
Input
Output
V
CC2
V
V
CC1
CC1
V
CC1
8 W
1 MW
OUT
500 W
IN
13 W
10
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
IEC SAFETY LIMITING VALUES
Safety limiting is designed to prevent potential damage to the isolation barrier upon failure of input or output
circuitry. A failure of the IO can allow low resistance to ground or the supply, and without current limiting,
dissipate sufficient power to overheat the die and damage the isolation barrier, potentially leading to secondary
system failures.
PARAMETER
TEST CONDITIONS
MIN
MAX UNIT
θJA = 263°C/W, VI = 5.5 V, TJ = 170°C, TA = 25°C
θJA = 263°C/W, VI = 3.6 V, TJ = 170°C, TA = 25°C
100
mA
153
IS
Safety input, output, or supply current
Maximum case temperature
TS
150
°C
The safety-limiting constraint is the absolute maximum junction temperature specified in the absolute maximum
ratings table. The power dissipation and junction-to-air thermal impedance of the device installed in the
application hardware determines the junction temperature. The junction-to-air thermal resistance in the Thermal
Characteristics table is that of a device installed in the JESD51-3, Low Effective Thermal Conductivity Test Board
for Leaded Surface Mount Packages and is conservative. The power is the recommended maximum input
voltage times the current. The junction temperature is then the ambient temperature plus the power times the
junction-to-air thermal resistance.
THERMAL CHARACTERISTICS
(over recommended operating conditions unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
263
125
44
MAX UNIT
Low-K(1)
High-K(1)
θJA
Junction-to-air thermal resistance
°C/W
θJB
θJC
Junction-to-board thermal resistance
Junction-to-case thermal resistance
°C/W
°C/W
75
VCC1 = VCC2 = 5.5 V, TJ = 150°C, CL = 15 pF,
Input a 100-Mbps 50% duty cycle square wave
PD
Device power dissipation
159 mW
(1) Tested in accordance with the Low-K or High-K thermal metric definition of EIA/JESD51-3 for leaded surface-mount packages.
200
175
V
, V
= 3.6 V
CC1 CC2
150
125
100
75
50
25
0
V
, V
= 5.5 V
CC1 CC2
0
50
100
Case Temperature
150
200
−
oC
Figure 5. θJC Thermal Derating Curve Per IEC 60747-5-2
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
FUNCTION TABLE(1)
INPUT
(IN)
OUTPUT
(OUT)
VCC1
VCC2
H
L
H
L
PU
PD
PU
PU
Open
X
H
H
(1) PU = powered up (VCC ≥ 3 V), PD = powered down (VCC ≤ 2.5 V), X = irrelevant, H = high level,
L = low level
12
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
TYPICAL CHARACTERISTICS
RMS SUPPLY CURRENT vs SIGNALING RATE
RMS SUPPLY CURRENT vs SIGNALING RATE
10
9
15
14
13
12
V
V
T
= 3.3 V,
= 3.3 V,
= 25oC,
V
V
T
= 5 V,
= 5 V,
= 25oC,
CC1
CC2
CC1
CC2
8
7
6
5
A
A
I
CC2
C
= 15 pF
C
= 15 pF
L
L
11
10
9
8
7
6
I
CC2
I
4
3
2
CC1
5
4
3
2
1
0
I
CC1
1
0
0
25
50
75
100
0
25
50
75
100
Signaling Rate (Mbps)
Signaling Rate (Mbps)
Figure 6.
Figure 7.
PROPAGATION DELAY vs FREE-AIR TEMPERATURE
30
PROPAGATION DELAY vs FREE-AIR TEMPERATURE
20
t
PLH
18
16
t
PLH
25
t
PHL
t
PHL
14
12
10
20
15
8
6
4
10
V
V
= 3.3 V,
= 3.3 V,
CC1
CC2
V
= 5 V,
= 5 V,
CC1
CC2
V
C
5
0
C
= 15 pF,
L
= 15 pF,
L
Air Flow at 7 cf/m
2
0
Air Flow at 7 cf/m
-40 -25 -10
5
20
35
50
65
80
95
110 125
-40 -25 -10
5
20
35
50
65
80
95
110 125
T
− Free-Air Temperature − o
C
T
− Free-Air Temperature − o
C
A
A
Figure 8.
Figure 9.
INPUT THRESHOLD VOLTAGE vs
FREE-AIR TEMPERATURE
VCC1 FAILSAFE THRESHOLD VOLTAGE vs
FREE-AIR TEMPERATURE
1.4
1.35
1.3
2.92
2.9
5-V (V
)
IT+
3.3-V (V
)
V
2.88
2.86
IT+
fs+
1.25
1.2
V
= 5 V or 3.3 V,
= 15 pF,
CC
C
L
Air Flow at 7 cf/m
Air Flow at 7 cf/m
2.84
2.82
1.15
1.1
1.05
1
5-V (V
)
IT-
V
fs-
2.8
3.3-V (V
)
IT-
2.78
-40 -25 -10
5
20
35
50
65
80
95
110 125
-40 -25 -10
5
20
35
50
65
80
95
110 125
− Free-Air Temperature − o
C
T
− Free-Air Temperature − o
C
T
A
A
Figure 10.
Figure 11.
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
TYPICAL CHARACTERISTICS (continued)
HIGH-LEVEL OUTPUT CURRENT vs HIGH-LEVEL OUTPUT
LOW-LEVEL OUTPUT CURRENT vs
LOW-LEVEL OUTPUT VOLTAGE
VOLTAGE
-80
70
60
T
= 25oC
= 25oC
A
T
-70
-60
-50
-40
-30
-20
A
V
= 5 V
CC
V
= 5 V
CC
50
40
30
20
V
= 3.3 V
V
= 3.3 V
CC
CC
10
0
-10
0
0
1
2
3
4
5
6
0
1
2
3
4
5
V
− High-Level Output Voltage − V
V
− Low-Level Output Voltage − V
OL
OH
Figure 12.
Figure 13.
14
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
APPLICATION INFORMATION
MANUFACTURER CROSS-REFERENCE DATA
The ISO721 isolator has the same functional pinout as most other vendors, and it is often a pin-for-pin drop-in
replacement. The notable differences in the product are propagation delay, signaling rate, power consumption,
and transient protection rating. Table 1 is used as a guide for replacing other isolators with the ISO721
single-channel isolators.
HCPL-xxxx
IL710
ISO721
ADuM1100
V
V
V
V
V
V
V
DD2
1
2
3
4
1
8
7
6
5
8
7
6
5
1
2
3
4
8
7
6
5
DD1
V
V
V
CC2
DD1
DD2
DD2
DD1
1
2
3
4
8
7
6
5
CC1
IN
V
I
V
V
2
3
4
NC
GND2
V
I
V
I
OE
O
GND2
OUT
V
O
V
O
NC
DD1
CC1
*
GND1
GND2
GND1
GND1
GND2
GND2
GND1
GND2
Figure 14. Pinout Cross Reference
Table 1. Competitive Cross Reference
ISOLATOR
ISO721(1)(2)
ADuM1100(1)(2)
HCPL-xxxx
IL710
PIN 1
VCC1
VDD1
PIN 2
PIN 3
VCC1
VDD1
PIN 4
GND1
GND1
PIN 5
GND2
GND2
PIN 6
PIN 7
PIN 8
VCC2
VDD2
IN
VI
OUT
VO
GND2
GND2
Leave
VDD1
VDD1
VI
VI
GND1
GND1
GND2
GND2
VO
VO
NC
VDD2
VDD2
Open(3)
NC(4)
VOE
(1) The ISO721 pin 1 and pin 3 are internally connected together. Either or both may be used as VCC1
.
(2) The ISO721 pin 5 and pin 7 are internally connected together. Either or both may be used as GND2.
(3) Pin 3 of the HCPL devices must be left open. This is not a problem when substituting an ISO721, because the extra VCC1 on pin 3 may
be left open circuit as well.
(4) Pin 3 of the IL710 must not be tied to ground on the circuit board, because this shorts the ISO721 VCC1 to ground. The IL710 pin 3 may
only be tied to VCC or left open to drop in an ISO721.
20 mm (max)
from VCC1
20 mm (max)
from VCC2
VCC1
VCC2
0.1 µF
0.1 µF
ISO721
1
2
3
4
8
7
6
5
Input
IN
Output
GND2
OUT
GND1
Figure 15. Basic Application Circuit
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): ISO721-Q1
ISO721-Q1
SLLS918–JULY 2008 ....................................................................................................................................................................................................... www.ti.com
ISOLATION GLOSSARY
Creepage Distance — The shortest path between two conductive input to output leads measured along the
surface of the insulation. The shortest distance path is found around the end of the package body.
Clearance — The shortest distance between two conductive input to output leads measured through air (line of
sight).
Input-to-Output Barrier Capacitance — The total capacitance between all input terminals connected together,
and all output terminals connected together.
Input-to-Output Barrier Resistance — The total resistance between all input terminals connected together, and
all output terminals connected together.
Primary Circuit — An internal circuit directly connected to an external supply mains or other equivalent source
which supplies the primary circuit electric power.
Secondary Circuit — A circuit with no direct connection to primary power, and derives its power from a separate
isolated source.
Comparative Tracking Index (CTI) — CTI is an index used for electrical insulating materials and is defined as
the numerical value of the voltage that causes failure by tracking during standard testing. Tracking is the process
that produces a partially conducting path of localized deterioration on or through the surface of an insulating
material as a result of the action of electric discharges on or close to an insulation surface -- the higher CTI value
of the insulating material, the smaller the minimum creepage distance.
Generally, insulation breakdown occurs either through the material, over its surface, or both. Surface failure may
arise from flashover or from the progressive degradation of the insulation surface by small localized sparks. Such
sparks are the result of the breaking of a surface film of conducting contaminant on the insulation. The resulting
break in the leakage current produces an overvoltage at the site of the discontinuity, and an electric spark is
generated. These sparks often cause carbonization on insulation material and lead to a carbon track between
points of different potential. This process is known as tracking.
16
Submit Documentation Feedback
Copyright © 2008, Texas Instruments Incorporated
Product Folder Link(s): ISO721-Q1
ISO721-Q1
www.ti.com ....................................................................................................................................................................................................... SLLS918–JULY 2008
Insulation
Operational insulation — Insulation needed for the correct operation of the equipment
Basic insulation — Insulation to provide basic protection against electric shock
Supplementary insulation — Independent insulation applied in addition to basic insulation in order to ensure
protection against electric shock in the event of a failure of the basic insulation
Double insulation — Insulation comprising both basic and supplementary insulation
Reinforced insulation — A single insulation system that provides a degree of protection against electric shock
equivalent to double insulation
Pollution Degree
Pollution Degree 1 — No pollution, or only dry, nonconductive pollution occurs. The pollution has no influence.
Pollution Degree 2 — Normally, only nonconductive pollution occurs. However, a temporary conductivity caused
by condensation must be expected.
Pollution Degree 3 — Conductive pollution occurs or dry nonconductive pollution occurs that becomes
conductive due to condensation, which is to be expected.
Pollution Degree 4 – Continuous conductivity occurs due to conductive dust, rain, or other wet conditions.
Installation Category
Overvoltage Category — This section addresses insulation coordination by identifying the transient overvoltages
that may occur and by assigning four different levels as indicated in IEC 60664.
I: Signal Level — Special equipment or parts of equipment
II: Local Level — Portable equipment, etc.
III: Distribution Level — Fixed installation
IV: Primary Supply Level — Overhead lines, cable systems
Each category should be subject to smaller transients than the category above.
Copyright © 2008, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): ISO721-Q1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明