LM25115AMT/NOPB [TI]
LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking;型号: | LM25115AMT/NOPB |
厂家: | TEXAS INSTRUMENTS |
描述: | LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking PC 开关 光电二极管 |
文件: | 总26页 (文件大小:917K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down
Tracking
Check for Samples: LM25115A
1
FEATURES
DESCRIPTION
The LM25115A controller contains all of the features
necessary to produce multiple tracking outputs using
the Secondary Side Post Regulation (SSPR)
technique. The SSPR technique develops a highly
efficient and well regulated auxiliary output from the
secondary side switching waveform of an isolated
power converter. LM25115A can be also used as a
standalone DC/DC synchronous buck controller
(Refer to Standalone DC/DC Synchronous Buck
Mode section). Regulation of the auxiliary output
voltage is achieved by leading edge pulse width
modulation (PWM) of the main channel duty cycle.
Leading edge modulation is compatible with either
current mode or voltage mode control of the main
output. The LM25115A drives external high-side and
low-side NMOS power switches configured as a
2
•
Power-up/Power-down Tracking
•
•
•
•
•
•
•
•
•
•
•
•
•
Self-synchronization to Main Channel Output
Leading Edge Pulse Width Modulation
Valley Current Mode Control
Standalone DC/DC Synchronous Buck Mode
Operates from AC or DC Input up to 42V
Wide 4.5V to 30V Bias Supply Range
Wide 0.75V to 13.5V Output Range.
Top and Bottom Gate Drivers Sink 2.5A Peak
Adaptive Gate Driver Dead-time Control
Wide Bandwidth Error Amplifier (4MHz)
Programmable Soft-start
Thermal Shutdown Protection
synchronous buck regulator.
A
current sense
amplifier provides overload protection and operates
over a wide common mode input range. Additional
features include a low dropout (LDO) bias regulator,
error amplifier, precision reference, adaptive dead
time control of the gate signals and thermal
shutdown.
TSSOP-16 package
Typical Application Circuit
Phase Signal
Main
Output
3.3V
FEEDBACK
Main Converter
PWM Controller
INPUT
SYNC
VCC
HB
+12V
LM25115A
R
S
HO
Auxiliary
Output
2.5V
VBIAS
RAMP
TRK/SS
CO
Main
3.3V
HS
LO
CS
COMP
VOUT
PGND AGND
FB
Figure 1. Simplified Multiple Output Power Converter Utilizing SSPR Technique
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2007–2013, Texas Instruments Incorporated
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Connection Diagram
1
2
3
4
5
16
15
14
13
12
11
10
9
VBIAS
HB
CS
VOUT
AGND
CO
HO
HS
VCC
COMP
6
7
FB
LO
TRK/SS
PGND
8
RAMP
SYNC
Figure 2. 16-Lead TSSOP
See Package Numbers PW0016A
2
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
PIN DESCRIPTIONS
Pin
Name
Description
Application Information
1
CS
Current Sense amplifier positive input
A low inductance current sense resistor is connected between CS
and VOUT. Current limiting occurs when the differential voltage
between CS and VOUT exceeds 45mV (typical).
2
VOUT
Current sense amplifier negative input
Connected directly to the output voltage. The current sense
amplifier operates over a voltage range from 0V to 13.5V at the
VOUT pin.
3
4
AGND
CO
Analog ground
Connect directly to the power ground pin (PGND).
Current limit output
For normal current limit operation, connect the CO pin to the
COMP pin through a diode. CO pin is connected to ground through
a resistor in series with a capacitor to provide adequate control
loop compensation for the current limit gm amplifier. Leave this pin
open to disable the current limit function.
5
6
COMP
FB
Compensation. Error amplifier output
Feedback. Error amplifier inverting input
COMP pin pull-up is provided by an internal 300uA current source.
Connected to the regulated output through the feedback resistor
divider and compensation components. The non-inverting input of
the error amplifier is internally connected to the SS pin.
7
8
9
TRK/SS
RAMP
SYNC
Tracking/Soft-start control
PWM Ramp signal
Non-inverting input to error amp with 15 µA pull-up current source.
Can be used with capacitor for soft-start or tied to external divider
of a master output for tracking. TRK/SS is the reference input to the
amplifier when the voltage applied to the pin is < 0.75V. For higher
inputs, the internal reference controls the amplifier.
An external capacitor connected to this pin sets the ramp slope for
the voltage mode PWM. The RAMP capacitor is charged with a
current that is proportional to current into the SYNC pin. The
capacitor is discharged at the end of every cycle by an internal
MOSFET.
Synchronization input
A low impedance current input pin. The current into this pin sets the
RAMP capacitor charge current and the frequency of an internal
oscillator that provides a clock for the free-run (DC input) mode .
10
11
PGND
LO
Power Ground
Connect directly to the analog ground pin (AGND).
Low-side gate driver output
Connect to the gate of the low-side synchronous MOSFET through
a short low inductance path.
12
VCC
Output of bias regulator
Nominal 7V output from the internal LDO bias regulator. Locally
decouple to PGND using a low ESR/ESL capacitor located as
close to controller as possible.
13
14
15
HS
HO
HB
High-side MOSFET source connection
High-side gate driver output
Connect to negative terminal of the bootstrap capacitor and the
source terminal of the high-side MOSFET.
Connect to the gate of high-side MOSFET through a short low
inductance path.
High-side gate driver bootstrap rail
Connect to the cathode of the bootstrap diode and the positive
terminal of the bootstrap capacitor. The bootstrap capacitor
supplies current to charge the high-side MOSFET gate and should
be placed as close to controller as possible.
16
VBIAS
Supply Bias Input
Input to the LDO bias regulator and current sense amplifier that
powers internal blocks. Input range of VBIAS is 4.5V to 30V.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ABSOLUTE MAXIMUM RATINGS(1)(2)
VBIAS to GND
–0.3V to 32V
–0.3V to 9V
VCC to GND
HS to GND
–1V to 45V
VOUT, CS to GND
All other inputs to GND
Storage Temperature Range
Junction Temperature
ESD Rating
– 0.3V to 15V
−0.3V to 7.0V
–55°C to +150°C
+150°C
(3)
HBM
2 kV
(1) Absolute Maximum Ratings indicate limits beyond which damage to the component may occur. Operating Ratings are conditions under
which operation of the device is specified. Operating Ratings do not imply ensured performance limits. For ensured performance limits
and associated test conditions, see the Electrical Characteristics tables.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The human body model is a 100 pF capacitor discharged through a 1.5kΩ resistor into each pin.
OPERATING RATINGS
VBIAS supply voltage
VCC supply voltage
HS voltage
5V to 30V
5V to 7.5V
0V to 42V
HB voltage
VCC + HS
Operating Junction Temperature
–40°C to +125°C
TYPICAL OPERATING CONDITIONS
Parameter
Min
4.5
Typ
Max
30
7
Units
V
Supply Voltage, VBIAS
Supply Voltage, VCC
4.5
V
Supply voltage bypass, CVBIAS
Reference bypass capacitor, CVCC
HB-HS bootstrap capacitor
0.1
1
1
µF
µF
µF
µA
V
0.1
10
0.047
50
SYNC Current Range (VCC = 4.5V)
RAMP Saw Tooth Amplitude
150
1.75
13.5
1
VOUT regulation voltage (VBIAS min = 3V + VOUT)
0.75
V
ELECTRICAL CHARACTERISTICS(1)
Unless otherwise specified, TJ = –40°C to +125°C, VBIAS = 12V, No Load on LO or HO.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
VBIAS SUPPLY
Ibias
VBIAS Supply Current
FSYNC = 200kHz
4
mA
VCC LOW DROPOUT BIAS REGULATOR
VccReg
VCC Regulation
VCC open circuit. Outputs not switching
6.65
7
7.15
V
mA
V
(2)
VCC Current Limit
(
)
40
VCC Under-voltage Lockout Voltage
VCC Under-voltage Hysteresis
Positive going VCC
4
4.5
0.3
0.2
0.25
V
(1) Min and Max limits are 100% production tested at 25°C. Limits over the operating temperature range are specified through correlation
using Statistical Quality Control (SQC) methods. Limits are used to calculate TI’s Average Outgoing Quality Level (AOQL).
(2) Device thermal limitations may limit usable range.
4
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
ELECTRICAL CHARACTERISTICS(1) (continued)
Unless otherwise specified, TJ = –40°C to +125°C, VBIAS = 12V, No Load on LO or HO.
Symbol
Parameter
Conditions
Min
10
Typ
Max
20
Units
TRACK / SOFT-START
SS Pull-up Source
15
µA
SS Discharge Impedance
140
Ω
ERROR AMPLIFIER and FEEDBACK REFERENCE
VREF
FB Reference Voltage
FB Input Bias Current
COMP Source Current
Open Loop Voltage Gain
Gain Bandwidth Product
Input Offset Voltage
COMP Offset
Measured at FB pin
.737
.750
0.2
300
60
4
.763
0.5
V
µA
µA
dB
MHz
mV
V
FB = 2V
GBW
Vio
22
2
Threshold for VHO = high RAMP = CS =
VOUT = 0V
RAMP Offset
Threshold for VHO = high COMP = 1.5V,
CS = VOUT = 0V
1.0
V
V
CURRENT SENSE AMPLIFIER
Current Sense Amplifier Headroom
Headroom = Vbias – Vout
3
Vbias= 4.5 V and Vout= 1.5 V
Current Sense Amplifier Gain
Output DC Offset
16
V/V
V
1.27
500
Amplifier Bandwidth
kHz
CURRENT LIMIT
Slow ILIMIT Amp Transconductance
Overall Transconductance
Slow ILimit Threshold
5
mA / V
mA / V
mV
90
45
VCL = VCS - VVOUT
VOUT = 6V and CO/COMP = 1.5V
39
34
51
46
Slow ILimit Foldback
VCL = VCS - VVOUT
39
mV
VOUT = 0V and CO/COMP = 1.5V
Fast ILimit Pull-Down Current
Fast ILimit Threshold
Vds = 2V
45
60
mA
mV
mV
VCLNEG
Negative Current Limit
VOUT = 6V
-17
VCL = VCS - VVOUT to cause LO to
shutoff
CO Clamp Voltage
ICO Pull-Up Current
5.5
6
6.5
V
15
µA
RAMP GENERATOR
SYNC Input Impedance
2.5
20
kΩ
µA
V
SYNC Threshold
End of cycle detection threshold
Free Run Mode Peak Threshold
RAMP peak voltage with dc current
applied to SYNC.
2.35
3.3
Current Mirror Gain
Ratio of RAMP charge current to SYNC
input current.
2.7
A/A
Discharge Impedance
100
Ω
LOW-SIDE GATE DRIVER
VOLL
VOHL
LO Low-state Output Voltage
LO High-state Output Voltage
LO Rise Time
ILO = 100mA
0.15
0.35
15
0.5
0.8
V
V
ILO = -100mA, VOHL = VCC -VLO
CLOAD = 1000pF
CLOAD = 1000pF
VLO = 0V
ns
ns
A
LO Fall Time
12
IOHL
IOLL
Peak LO Source Current
Peak LO Sink Current
2
VLO = 12V
2.5
A
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Units
ELECTRICAL CHARACTERISTICS(1) (continued)
Unless otherwise specified, TJ = –40°C to +125°C, VBIAS = 12V, No Load on LO or HO.
Symbol
Parameter
Conditions
Min
Typ
Max
HIGH-SIDE GATE DRIVER
VOLH
VOHH
HO Low-state Output Voltage
HO High-state Output Voltage
HO Rise Time
IHO = 100mA
0.15
0.35
15
0.5
0.8
V
V
IHO = -100mA, VOHH = VHB –VHO
CLOAD = 1000pF
CLOAD = 1000pF
VHO = 0V
ns
ns
A
HO High-side Fall Time
Peak HO Source Current
Peak HO Sink Current
12
IOHH
IOLH
2
VHO = 12V
2.5
A
SWITCHING CHARACTERISITCS
LO Fall to HO Rise Delay
HO Fall to LO Rise Delay
SYNC Fall to HO Fall Delay
SYNC Rise to LO Fall Delay
THERMAL SHUTDOWN
CLOAD = 0
CLOAD = 0
CLOAD = 0
CLOAD = 0
40
50
ns
ns
ns
ns
120
80
TSD
Thermal Shutdown Temp.
150
165
25
°C
°C
Thermal Shutdown Hysteresis
THERMAL RESISTANCE
θJA
θJA
Junction to Ambient
Junction to Ambient
PW Package
SDA Package
125
32
°C/W
°C/W
6
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
TYPICAL PERFORMANCE CHARACTERISTICS
Efficiency
vs.
Load Current and Vphase
(VOUT = 2.5V)
VCC Regulator Start-up Characteristics, VCC
vs.
VBIAS
100
98
96
94
92
90
88
86
84
82
16
14
Vphase = 6V
V
BIAS
12
10
8
Vphase = 8V
V
CC
Vphase = 12V
6
4
2
0
0
1
2
3
4
5
6
7
0
2
4
6
8
10 12 14 16
(V)
LOAD (A)
V
BIAS
Figure 3.
Figure 4.
Current Value (CV)
vs.
Current Sense Amplifier Gain and Phase
vs.
Current Limit (VCL
)
Frequency
2.5
2
5
25
20
15
10
5
Gain
V
= 6V
OUT
-10
Phase
16 V/V
1.5
1
-25
-40
-55
-70
Offset 1.27V
0.5
0
0
-20 -10
0
10 20 30 40 50 60
(mV)
100
1K
10K
100K
1M
V
CL
FREQUENCY (Hz)
Figure 5.
Figure 6.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
TYPICAL PERFORMANCE CHARACTERISTICS (continued)
Current Error Amplifier Transconductance
Overall Current Amplifier Transconductance
300
200
100
0
700
V
OUT
= 6V
600
500
V
= 0V
OUT
V
OUT
= 6V
5.9 mA/V
400
300
88 mA/V
-100
99 mA/V
200
100
-200
-300
0
30 32 34 36 38 40 42 44 46 48
2.1
1.96 1.98
2
2.02 2.04 2.06 2.08
(V)
V
CS
- V (mV)
OUT
C
V
Figure 7.
Figure 8.
Common Mode Output Voltage
vs.
Common Mode Output Voltage
vs.
Negative Current Limit (Room Temp)
Positive Current Limit
12
10
8
14
12
10
-40oC
125oC
8
6
4
6
4
2
27oC
2
0
0
0
10
20
V
30
(mV)
40
50
-17.8 -17.6-17.4 -17.2 -17 -16.8-16.6-16.4-16.2
CL
V
CL
(mV)
Figure 9.
Figure 10.
VCC Load Regulation to Current Limit
8
7
6
5
4
3
2
1
0
0
5
10 15 20 25 30 35 40 45 50
(mA)
I
CC
Figure 11.
8
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
BLOCK DIAGRAM
V
CC
VBIAS
SYNC
7V LDO
REGULATOR
V
CC
LOGIC
UVLO
7V
THERMAL
LIMIT
HB
HO
HS
15 mA
I
V
SYNC
CC
2.5k
CLK
2.5k
R
S
Q
Q
LEVEL
SHIFT
DRIVER
V
CC
I
x 3
SYNC
RAMP
0.7V
ADAPTIVE
DEAD TIME
DELAY
BUFFER
100k
55k
CLK
CRMIX
V
CC
FB
PWM
COMPARATOR
40k
V
CC
LO
V
CC
DRIVER
ERROR AMP
(Sink Only)
15 mA
300 mA
NEGATIVE
CURRENT
DETECTOR
TRK/SS
PGND
1V
0.75V
AGND
ENABLE
ILIMIT SLOW
Gm = 5 mA/V
COMP
CV
ILIMIT FAST
CURRENT SENSE AMP
Gain = 16
CS
VBIAS
2V
1.27V
CC
V
OUT
V
2.35V
15 mA
CO
VINT
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
DETAILED OPERATING DESCRIPTION
The LM25115A controller contains all of the features necessary to implement multiple output power converters
utilizing the Secondary Side Post Regulation (SSPR) technique. The SSPR technique develops a highly efficient
and well regulated auxiliary output from the secondary side switching waveform of an isolated power converter.
Regulation of the auxiliary output voltage is achieved by leading edge pulse width modulation (PWM) of the main
channel duty cycle. Leading edge modulation is compatible with either current mode or voltage mode control of
the main output. The LM25115A drives external high-side and low-side NMOS power switches configured as a
synchronous buck regulator. A current sense amplifier provides overload protection and operates over a wide
common mode input range from 0V to 13.5V. Additional features include a low dropout (LDO) bias regulator,
error amplifier, precision reference, adaptive dead time control of the gate driver signals and thermal shutdown.
Low Drop-Out Bias Regulator (VCC)
The LM25115A contains an internal LDO regulator that operates over an input supply range from 4.5V to 30V.
The output of the regulator at the VCC pin is nominally regulated at 7V and is internally current limited to 40mA.
VCC is the main supply to the internal logic, PWM controller, and gate driver circuits. When power is applied to
the VBIAS pin, the regulator is enabled and sources current into an external capacitor connected to the VCC pin.
The recommended output capacitor range for the VCC regulator is 0.1uF to 100uF. When the voltage at the VCC
pin reaches the VCC under-voltage lockout threshold of 4.25V, the controller is enabled. The controller is
disabled if VCC falls below 4.0V (250mV hysteresis). In applications where an appropriate regulated dc bias
supply is available, the LM25115A controller can be powered directly through the VCC pin instead of the VBIAS
pin. In this configuration, it is recommended that the VCC and the VBIAS pins be connected together such that
the external bias voltage is applied to both pins. The allowable VCC range when biased from an external supply
is 4.5V to 7V.
Synchronization (SYNC) and Feed-Forward (RAMP)
The pulsing “phase signal” from the main converter synchronizes the PWM ramp and gate drive outputs of the
LM25115A. The phase signal is the square wave output from the transformer secondary winding before
rectification (Figure 1). A resistor connected from the phase signal to the low impedance SYNC pin produces a
square wave current (ISYNC) as shown in Figure 12. A current comparator at the SYNC input monitors ISYNC
relative to an internal 15µA reference. When ISYNC exceeds 15µA, the internal clock signal (CLK) is reset and the
capacitor connected to the RAMP begins to charge. The current source that charges the RAMP capacitor is
equal to 3 times the ISYNC current. The falling edge of the phase signal sets the CLK signal and discharges the
RAMP capacitor until the next rising edge of the phase signal. The RAMP capacitor is discharged to ground by a
low impedance (100Ω) n-channel MOSFET. The input impedance at SYNC pin is 2.5kΩ which is normally much
smaller than the external SYNC pin resistance.
The RAMP and SYNC functions illustrated in Figure 12 provide line voltage feed-forward to improve the
regulation of the auxiliary output when the input voltage of the main converter changes. Varying the input voltage
to the main converter produces proportional variations in amplitude of the phase signal. The main channel PWM
controller adjusts the pulse width of the phase signal to maintain constant volt*seconds and a regulated main
output as shown in Figure 13. The variation of the phase signal amplitude and duration are reflected in the slope
and duty cycle of the RAMP signal of the LM25115A (ISYNC α phase signal amplitude). As a result, the duty cycle
of the LM25115A is automatically adjusted to regulate the auxiliary output voltage with virtually no change in the
PWM threshold voltage. Transient line regulation is improved because the PWM duty cycle of the auxiliary
converter is immediately corrected, independent of the delays of the voltage regulation loop.
10
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
Phase
Signal
R
SYNC
SYNC
Isync
CLK
15 mA
2.5k
2.5k
Isync x 3
RAMP
BUFFER
C
RAMP
CLK
Figure 12. Line Feed-Forward Diagram
12V
Phase signal
6V
Main Output = 3.3V
PWM Threshold
RAMP pin
HS pin
12V
6V
Secondary Output = 2.5V
Figure 13. Line Feed-Forward Waveforms
The recommended SYNC input current range is 50µA to 150µA. The SYNC pin resistor (RSYNC) should be
selected to set the SYNC current (ISYNC) to 150µA with the maximum phase signal amplitude, VPHASE(max). This
will ensure that ISYNC stays within the recommended range over a 3:1 change in phase signal amplitude. The
SYNC pin resistor is therefore:
RSYNC = (VPHASE(max) / 150µA) - 2.5kΩ
Once ISYNC has been established by selecting RSYNC, the RAMP signal slope/amplitude may be programmed by
selecting the proper RAMP pin capacitor value. The RAMP signal slope should be selected to provide adequate
slope compensation for the Valley current mode control scheme (Please refer to the Valley Current Mode Control
section). The recommended peak amplitude of the ramp waveform is 1.75V.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Error Amplifier and Soft-Start (FB, CO, COMP & TRK/SS)
An internal wide bandwidth error amplifier is provided within the LM25115A for voltage feedback to the PWM
controller. The amplifier’s inverting input is connected to the FB pin. The output of the auxiliary converter is
regulated by connecting a voltage setting resistor divider between the output and the FB pin. Loop compensation
networks are connected between the FB pin and the error amplifier output (COMP). The amplifier has two non-
inverting inputs. The first non-inverting input connects to a 0.75V bandgap reference while the second non-
inverting input connects to the TRK/SS pin and it has 15 µA pull-up current source. The TRK/SS pin can be tied
to an external resistor divider from the master output for tracking, or it can be tied to a capacitor for soft-start .
TRK/SS is the reference input to the amplifier when the voltage applied to the pin is < 0.75V. For higher inputs,
the internal reference controls the amplifier. When the VCC voltage is below the UVLO threshold, the TRK/SS
pin is discharged to ground. When VCC rises and exceeds the positive going UVLO threshold (4.25V), the
TRK/SS pin is released and allowed to rise. If an external capacitor is connected to the TRK/SS pin, it will be
charged by the internal 15uA pull-up current source to gradually increase the non-inverting input of the error
amplifier to 0.75V. During start-up, the output of the LM25115A converter will follow the following equation:
VOUT(t) = VOUT(final) x15 µA x t /(.75 Vx Css )
where
•
•
Css = external Soft-Start capacitor
VOUT(final) = regulator output set point
Pull-up current for the error amplifier output is provided by an internal 300µA current source. The PWM threshold
signal at the COMP pin can be controlled by either the open drain error amplifier or the open drain current
amplifier connected through the CO pin to COMP. Since the internal error amplifier is configured as an open
drain output it can be disabled by connecting FB to ground. The current sense amplifier and current limiting
function will be described in a later section.
Power-Up/Power-Down Tracking
The LM25115A can track the output of a master power supply during soft start by connecting a resistor divider to
the TRACK pin (Figure 14). Therefore, the output voltage slew rate of the LM25115A will be controlled by the
master supply for loads that require precise sequencing. In order to track properly the output voltage of the
LM25115A must be lower than the output voltage of the master supply.
One way to use the tracking feature is to design the tracking resistor divider so that the master supply output
voltage (VOUT1) and the LM25115A output voltage (VOUT2) both rise together and reach their target values at
the same time. For this case, the equation governing the values of the tracking divider resistors RT1 and RT2 is:
0.8 x RT2
RT1
=
VOUT1 - 0.8
A value of 10kΩ (1%) is recommended for RT2 as a good compromise between high precision and low quiescent
current through the divider. If the master supply voltage was 3.3V and the LM25115A output voltage was 2.5 V,
then the value of RT1 needed to give the two supplies identical soft start times would be 2.94 kΩ (1%). The
timing diagram and waveforms for the equal soft start time configuration are shown in Figure 15 and Figure 16.
12
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
3.3V
Master
Power
Supply
V
OUT1
V
OUT1
V
R
OUT2
T2
2.5V
V
TRACK
LM5115A
SS
V
OUT2
R
V
R
FB2
T1
FB
FB
R
FB1
Figure 14.
Figure 15.
Vphase = 10V
CH1 = Master output, 1V/Div
CH2 = COMP, 5/Div
CH3 = Iout, 1A/Div
CH4 = SSPR Output (Slave), 1V/Div
Horizontal Resolution= 200 µs/Div
Figure 16. Tracking with Equal Soft Start Time
Alternatively, the tracking feature can be used to create equal slew rates between the output voltages of the
master supply and the LM25115A. This method ensures that the output voltage of the LM25115A always
reaches regulation before the output voltage of the master supply. In this case, the tracking resistors can be
determined based on the following equation:
0.8 x RT2
RT1
=
VOUT2 - 0.8
Again, a value of 10kΩ 1% is recommended for RT2. For the case of VOUT1 = 3.3V and VOUT2 = 2.5V, RT1
should be 4.32 kΩ 1%. The timing diagram and the waveforms for equal slew rates configuration are shown in
Figure 17 and Figure 18.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
3.3V
2.5V
V
OUT1
2.5V
V
OUT2
Figure 17.
Vphase = 10V
CH1 = Master output, 1V/Div
CH2 = COMP, 5/Div
CH3 = Iout, 1A/Div
CH4 = SSPR Output (Slave), 1V/Div
Horizontal Resolution= 200 µs/Div
Figure 18. Tracking with Equal Slew Rate
Leading Edge Pulse Width Modulation
Unlike conventional voltage mode controllers, the LM25115A implements leading edge pulse width modulation. A
current source equal to 3 times the ISYNC current is used to charge the capacitor connected to the RAMP pin as
shown in Figure 19. The ramp signal and the output of the error amplifier (COMP) are combined through a
resistor network to produce a voltage ramp with variable dc offset (CRMIX in Figure 19). The high-side MOSFET
which drives the HS pin is held in the off state at the beginning of the phase signal. When the voltage of CRMIX
exceeds the internal threshold voltage CV, the PWM comparator turns on the high-side MOSFET. The HS pin
rises and the MOSFET delivers current from the main converter phase signal to the output of the auxiliary
regulator. The PWM cycle ends when the phase signal falls and power is no longer supplied to the drain of the
high-side MOSFET.
Leading edge modulation of the auxiliary PWM controller is required if the main converter uses peak current
mode control. If trailing edge modulation were used, the additional load on the transformer secondary from the
auxiliary channel would be drawn only during the first portion of the phase signal pulse. Referring to Figure 20,
the turn-off of the high- side MOSFET of the auxiliary regulator would create a non-monotonic negative step in
the transformer current. This negative current step would produce instability in a peak current mode controller.
With leading edge modulation, the additional load presented by the auxiliary regulator on the transformer
secondary will be present during the latter portion of the phase signal. This positive step in the phase signal
current can be accommodated by a peak current mode controller without instability.
14
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
Isync x 3
0.7V
RAMP
Phase or CLK
RAMP
BUFFER
CLK
C
RAMP
55k
CRMIX
PWM
CV
40k
CRMIX
COMP
CV
ERROR
AMP
FB
100k
HS
TRK/SS
Leading Edge
Modulation
0.75V
Figure 19. Synchronization and Leading Edge Modulation
Main
Main
PWM
PWM
Auxilary
PWM
Auxilary
PWM
Leading Edge
Modulation
Trailing Edge
Modulation
Peak Current
Threshold
Peak Current
Threshold
Transformer
Current
Transformer
Current
Figure 20. Leading versus Trailing Edge Modulation
Valley Current Mode Control
The LM25115A controller uniquely utilizes the elements and benefits of valley current mode control in
conjunction with leading edge modulation to correct changes in output voltage due to line and load transients.
Contrary to peak current mode control, valley current mode control turns on the high-side MOSFET when the
inductor valley current reaches a programmable threshold. This programmable threshold (CRMIX) is the sum of
the output of voltage error amplifier and the RAMP signal generated at the RAMP pin. Valley current mode
control experiences sub-harmonic oscillation when the duty ratio, D, is less than or equal to 50%. Therefore,
adequate slope compensation is needed for the proper operation across the full range of the duty ratio. The
RAMP signal is proportional to the input voltage and it provides the required slope compensation for the valley
current mode scheme. The desired RAMP pin capacitance can be calculated from the following equation:
CRAMP = (0.05 x L) /(RSYNC x RSENSE
)
where
•
•
•
L is the power inductor
RSYNC is the SYNC pin resistor
RSENSE is the current sense resistor
The current sense amplifier shown in Figure 21 monitors the inductor current as it flows through a sense resistor
connected between CS and VOUT. The voltage gain of the sense amplifier is nominally equal to 16. The current
sense output signal is shifted by 1.27V to produce the internal CV reference signal. The CV signal is applied to
the negative input of the PWM comparator and compared to CRMIX as illustrated in Figure 21. Therefore when
CRMIX exceeds the PWM threshold (CV), the PWM comparator turns on the high-side MOSFET. Insure that the
Vbias voltage is at least 3V above the regulated output voltage (VOUT) to provide enough headroom for the
current sense amplifier.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Valley current mode control improves the control loop stability and bandwidth. It also eliminates the R-C lead
network in the feedback path that is normally required with voltage mode control (Figure 22). Eliminating the lead
network not only simplifies the compensation, but also reduces sensitivity to output noise that could pass through
the lead network to the error amplifier.
The design of the voltage feedback path through the error amp begins with the selection of R1 and R2 in
Figure 22 to set the regulated output voltage. The steady state output voltage after soft-start is determined by the
following equation:
VOUT(final) = 0.75V x (1+R1/R2)
The parallel impedance of the R1, R2 resistor divider should be approximately 2kΩ (between 0.5kΩ and 5kΩ).
Lower resistance values may not be properly driven by the error amplifier output and higher feedback resistances
can introduce noise sensitivity. The next step in the design process is selection of R3, which sets the ac gain of
the error amplifier.
The capacitor C1 is connected in series with R3 to increase the dc gain of the voltage regulation loop and
improve output voltage accuracy. The corner frequency set by R3 x C1 should be less than 1/10th of the cross-
over frequency of the overall converter such that capacitor C1 does not add phase lag at the crossover
frequency.
Negative Current
Comparator
Low Side
Enable
1V
ILIMIT SLOW
Gm = 5 mA/V
CS
Vbias
1.27V
ILIMIT FAST
CO
2V
V
CL
V
OUT
AV=16
Current
2.35V
Sense Amp
PWM
Comparator
CV
to PWM
Latch
CRMIX
ERROR
AMP
COMP
FB
TRK/SS
0.75V
Figure 21. Current Sensing and Limiting
V
OUT
No Lead
Network
Required
R1
PWM
ERROR
AMP
FB
CV
40k
TRK/SS
0.75V
100k
COMP
R3
C1
R2
Figure 22. Voltage Sensing and Feedback
16
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
Current Limiting (CS, CO and VOUT)
Current limiting is implemented through the current sense amplifier as illustrated in Figure 21. The current sense
amplifier monitors the inductor current that flows through a sense resistor connected between CS and VOUT.
The voltage gain of the current sense amplifier is nominally equal to 16. The output of current sense signal is
shifted by 1.27V to produce the internal CV reference signal. The CV signal drives two current limit amplifiers.
Both of the current limit amplifiers have open drain (sink only) output stages which are connected to the CO pin.
The CO pin is typically connected to the COMP pin through a diode (the cathode is connected to the CO pin and
the anode is connected to the COMP pin). The slow current limit amplifier has a nominal transconductance of 5
mA/V and provides constant current mode operation at the desired current limit set point. The fast current limit
amplifier has nominal current pull-down capability of 100mA and provides protection against fast over-current
conditions. During normal operation, the voltage error amplifier controls the COMP pin voltage which adjusts the
PWM duty cycle by varying the internal CRMIX level. However when the current sense input voltage, VCL
,
exceeds 45mV, the slow current limit amplifier gradually pulls down on COMP through the CO pin. Pulling COMP
low reduces the CRMIX signal and thereby reducing the operating duty cycle. By controlling the operating duty
cycle, the slow current limit amplifier will force a constant current mode of operation at the desired current limit
set point (Figure 23). A resistor in series with a capacitor are connected from the CO Pin to ground to provide
adequate control loop compensation for the slow current limit (Figure 21). The desired current limit set point,
ILimit, can be programmed by selecting the proper current sense resistor, RSENSE,using the following equation:
RSENSE = 0.045 V/ ILimit
In the event that the current sense input voltage, VCL, exceeds 60mV, the fast current limit amplifier will pull down
hard on COMP through the CO pin. This will reduce the CRMIX signal to a voltage below the CV signal level.
Therefore, the PWM comparator will inhibit output pulses. Once the fault condition is removed, the fast current
limit amplifier will release COMP. Therefore, the CRMIX signal will increase to a normal operating threshold and
the switching will resume (Figure 24). A current limit fold-back feature is provided by the LM25115A to reduce the
peak output current delivered to a shorted load. When the common mode input voltage to the current sense
amplifier (CS and VOUT pins) falls below 2V, the current limit threshold is reduced from the normal level. At
common mode voltages > 2V, the current limit threshold is nominally 45mV. When VOUT is reduced to 0 V the
current limit threshold drops to 39mV to reduce stress on the inductor and power MOSFETs.
Vphase=10V
CH1 = CO, 5V/Div
CH2 = COMP, 5/Div
CH3 = Iout, 5A/Div
CH4 = SSPR Switch Signal, 5V/Div
Horizontal Resolution= 2 µs/Div
Figure 23. SSPR Steady State Current Limit (Output Shorted)
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Vphase=10V
CH1 = CO, 5V/Div
CH2 = COMP, 5/Div
CH3 = Iout, 10A/Div
CH4 = SSPR Switch Signal, 4V/Div
Horizontal Resolution= 20 µs/Div
Figure 24. SSPR Short Circuit Transient (No-Load to Short-Circuit)
Negative Current Limit
Under certain conditions synchronous buck regulators are capable of sinking current from the output capacitors.
This energy is stored in the inductor and returned to the input source. The LM25115A detects this current
reversal by detecting a negative voltage being developed across the current sense resistor. The intent of this
negative current comparator is to protect the low-side MOSFET from excessive currents. Excessive negative
current can also lead to a large positive voltage spike on the HS pin at the turn-off of the low-side MOSFET. This
voltage spike may damage the chip if its magnitude exceeds the maximum voltage rating of the part. The
negative current comparator threshold is sufficiently negative to allow inductor current to reverse at no load or
light load conditions. It is not intended to support discontinuous conduction mode with diode emulation by the
low-side MOSFET. The negative current comparator shown in Figure 21 monitors the CV signal and compares
this signal to a fixed 1V threshold. This corresponds to a negative VCL voltage between CS and VOUT of -17mV.
The negative current limit comparator turns off the low-side MOSFET for the remainder of the cycle when the VCL
input falls below this threshold.
Gate Driver Outputs (HO & LO)
The LM25115A provides two gate driver outputs, the floating high-side gate driver HO and the synchronous
rectifier low-side driver LO. The low-side driver is powered directly by the VCC regulator. The high-side gate
driver is powered from a bootstrap capacitor connected between HB and HS. An external diode connected
between VCC and HB charges the bootstrap capacitor when the HS is low. When the high-side MOSFET is
turned on, HB rises with HS to a peak voltage equal to VCC + VHS - VD where VD is the forward drop of the
external bootstrap diode. Both output drivers have adaptive dead-time control to avoid shoot through currents.
The adaptive dead-time control circuit monitors the state of each driver to ensure that one MOSFET is turned off
before the other is turned on. The HB and VCC capacitors should be placed close to the pins of the LM25115A
to minimize voltage transients due to parasitic inductances and the high peak output currents of the drivers. The
recommended range of the HB capacitor is 0.047µF to 0.22µF.
Both drivers are controlled by the PWM logic signal from the PWM latch. When the phase signal is low, the
outputs are held in the reset state with the low-side MOSFET on and the high-side MOSFET off. When the phase
signal switches to the high state, the PWM latch reset signal is de-asserted. The high-side MOSFET remains off
until the PWM latch is set by the PWM comparator (CRMIX > CV as shown in Figure 19). When the PWM latch
is set, the LO driver turns off the low-side MOSFET and the HO driver turns on the high-side MOSFET. The high-
side pulse is terminated when the phase signal falls and SYNC input comparator resets the PWM latch.
18
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
Thermal Protection
Internal thermal shutdown circuitry is provided to protect the integrated circuit in the event the maximum junction
temperature limit is exceeded. When activated, typically at 165 degrees Celsius, the controller is forced into a low
power standby state with the output drivers and the bias regulator disabled. The device will restart when the
junction temperature falls below the thermal shutdown hysteresis, which is typically 25 degrees. The thermal
protection feature is provided to prevent catastrophic failures from accidental device overheating.
Standalone DC/DC Synchronous Buck Mode
The LM25115A can be configured as a standalone DC/DC synchronous buck controller. In this mode the
LM25115A uses leading edge modulation in conjunction with valley current mode control to control the
synchronous buck power stage. The internal oscillator within the LM25115A sets the clock frequency for the high
and low-side drivers of the external synchronous buck power MOSFETs . The clock frequency in the
synchronous buck mode is programmed by the SYNC pin resistor and RAMP pin capacitor. Connecting a
resistor between a dc bias supply and the SYNC pin produces a current, ISYNC, which sets the charging current of
the RAMP pin capacitor. The RAMP capacitor is charged until its voltage reaches the peak ramp threshold of
2.25V. The RAMP capacitor is then discharged for 300ns before beginning a new PWM cycle. The 300ns reset
time of the RAMP pin sets the minimum off-time of the PWM controller in this mode. The internal clock frequency
in the synchronous buck mode is set by ISYNC, the ramp capacitor, the peak ramp threshold, and the 300ns
deadtime.
FCLK ≊ 1 / ((CRAMP x 2.25V) / (ISYNC x 3) + 300ns)
See the LM5115 dc evaluation board application note (AN-1367, literature number SNVA106) for more details on
the synchronous buck mode. Please note that LM25115A is similar to LM5115 except for the tracking feature.
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Links: LM25115A
LM25115A
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
www.ti.com
Application Circuit
(Inputs from LM5025 Forward Active Clamp Converter, 36V to 78V)
Figure 25. LM25115A Secondary Side Post Regulator
20
Submit Documentation Feedback
Copyright © 2007–2013, Texas Instruments Incorporated
Product Folder Links: LM25115A
LM25115A
www.ti.com
SNVS501B –FEBRUARY 2007–REVISED APRIL 2013
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 19
Copyright © 2007–2013, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Links: LM25115A
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
PACKAGING INFORMATION
Orderable Device
LM25115AMT/NOPB
LM25115AMTX/NOPB
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
TSSOP
TSSOP
PW
16
16
92
Green (RoHS
& no Sb/Br)
CU SN
CU SN
Level-1-260C-UNLIM
L25115
AMT
ACTIVE
PW
2500
Green (RoHS
& no Sb/Br)
Level-1-260C-UNLIM
-40 to 125
L25115
AMT
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM25115AMTX/NOPB
TSSOP
PW
16
2500
330.0
12.4
6.95
5.6
1.6
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Nov-2015
*All dimensions are nominal
Device
Package Type Package Drawing Pins
TSSOP PW 16
SPQ
Length (mm) Width (mm) Height (mm)
367.0 367.0 35.0
LM25115AMTX/NOPB
2500
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2015, Texas Instruments Incorporated
相关型号:
LM25115AMTX/NOPB
LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking
TI
LM25115A_15
LM25115A Secondary Side Post Regulator/DC-DC Converter with Power-Up/Power-Down Tracking
TI
LM25115MTX/NOPB
42V, Secondary Side Post Regulator/Synchronous Buck Controller 16-TSSOP -40 to 125
TI
©2020 ICPDF网 联系我们和版权申明