LM34914 [TI]
具有智能电流限制的超小型 1.25A 降压开关稳压器;
| 型号： | LM34914 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | 具有智能电流限制的超小型 1.25A 降压开关稳压器 开关 稳压器 |
| 文件： | 总21页 (文件大小：1196K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
LM34914 Ultra Small 1.25A Step-Down Switching Regulator with Intelligent Current Limit
Check for Samples: LM34914
1
FEATURES
DESCRIPTION
The LM34914 Step-Down Switching Regulator
features all the functions needed to implement a low
cost, efficient, buck bias regulator capable of
supplying at least 1.25A to the load. To reduce
excessive switch current due to the possibility of a
saturating inductor the valley current limit threshold
changes with input and output voltages, and the on-
time is reduced when current limit is detected. This
buck regulator contains a 44V N-Channel Buck
Switch, and is available in the thermally enhanced 3
mm x 3 mm WSON-10 package. The feedback
regulation scheme requires no loop compensation,
results in fast load transient response, and simplifies
circuit implementation. The operating frequency
remains constant with line and load variations due to
the inverse relationship between the input voltage
and the on-time. The valley current limit results in a
smooth transition from constant voltage to constant
current mode when current limit is detected, reducing
the frequency and output voltage, without the use of
foldback. Additional features include: VCC under-
voltage lock-out, thermal shutdown, gate drive under-
voltage lock-out, and maximum duty cycle limit.
2
•
Input Voltage Range: 8V to 40V
•
•
Integrated N-Channel Buck Switch
Valley Current Limit Varies with VIN and VOUT
to Reduce Excessive Inductor Current
•
•
•
•
•
•
On-time is Reduced when in Current Limit
Integrated Start-Up Regulator
No Loop Compensation Required
Ultra-Fast Transient Response
Maximum Switching Frequency: 1.3 MHz
Operating Frequency Remains Nearly
Constant with Load Current and Input Voltage
Variations
•
•
•
•
Programmable Soft-Start
Precision Internal Reference
Adjustable Output Voltage
Thermal Shutdown
TYPICAL APPLICATIONS
•
•
•
High Efficiency Point-Of-Load (POL) Regulator
Non-Isolated Buck Regulator
Package
•
•
WSON-10 (3 mm x 3mm)
Exposed Thermal Pad For Improved Heat
Dissipation
Secondary High Voltage Post Regulator
Basic Step Down Regulator
8V - 40V
Input
V
CC
V
IN
C3
C1
LM34914
R
ON
BST
SW
L1
RON/SD
SS
C4
V
OUT
SHUT
DOWN
D1
R1
R2
R3
ISEN
FB
C5
C2
RTN
SGND
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
All trademarks are the property of their respective owners.
2
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2006–2013, Texas Instruments Incorporated
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
Connection Diagram
1
2
3
4
5
10
9
SW
V
IN
BST
V
CC
8
RON/SD
ISEN
SGND
RTN
7
SS
FB
6
10-Lead WSON
PIN DESCRIPTIONS
Pin Number
Name
Description
Application Information
Internally connected to the buck switch source. Connect to
the inductor, diode, and bootstrap capacitor.
1
SW
Switching Node
Connect a 0.022 µF capacitor from SW to this pin. The
capacitor is charged each off-time via an internal diode.
2
3
4
5
6
7
8
BST
ISEN
SGND
RTN
Boost pin for bootstrap capacitor
Current sense
The re-circulating current flows out of this pin to the free-
wheeling diode.
Re-circulating current flows into this pin to the current sense
resistor.
Sense Ground
Ground for all internal circuitry other than the current limit
detection.
Circuit Ground
Feedback input from the regulated
output
Internally connected to the regulation and over-voltage
comparators. The regulation level is 2.5V.
FB
An internal current source charges an external capacitor to
2.5V, providing the softstart function.
SS
Softstart
An external resistor from VIN to this pin sets the buck switch
on-time. Grounding this pin shuts down the regulator.
RON/SD
On-time control and shutdown
Nominally regulated at 7.0V. Connect a 0.1 µF capacitor from
this pin to RTN. An external voltage (8V to 14V) can be
applied to this pin to reduce internal dissipation. An internal
diode connects VCC to VIN.
9
VCC
Output from the startup regulator
10
VIN
EP
Input supply voltage
Exposed Pad
Operating input range is 8.0V to 40V.
Exposed metal pad on the underside of the device. It is
recommended to connect this pad to the PC board ground
plane to aid in heat dissipation.
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
2
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
Absolute Maximum Ratings(1)(2)
VIN to RTN
44V
BST to RTN
52V
SW to RTN (Steady State)
BST to VCC
-1.5V
44V
VIN to SW
44V
BST to SW
14V
VCC to RTN
14V
SGND to RTN
-0.3V to +0.3V
See text
-0.3V to 4V
-0.3 to 7V
2kV
Current out of ISEN
SS to RTN
All Other Inputs to RTN
ESD Rating(3)
Human Body Model
Storage Temperature Range
JunctionTemperature
-65°C to +150°C
150°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see Electrical Characteristics.
(2) If Military/Aerospace specified devices are required, please contact the Texas Instruments Sales Office/Distributors for availability and
specifications.
(3) The human body model is a 100pF capacitor discharged through a 1.5kΩ resistor into each pin.
Operating Ratings(1)
VIN Voltage
8.0V to 40V
Junction Temperature
−40°C to + 125°C
(1) Absolute Maximum Ratings are limits beyond which damage to the device may occur. Operating Ratings are conditions under which
operation of the device is intended to be functional. For specifications and test conditions, see Electrical Characteristics.
Electrical Characteristics
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C
to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the
following conditions apply: VIN = 12V, RON = 200kΩ(1)(2)
.
Symbol
Parameter
Conditions
Min
6.6
Typ
Max
7.4
Units
Start-Up Regulator, VCC
VCCReg
VCC regulated output
Vin > 9V
7.0
1.3
V
V
ICC = 0 mA,
VCC = UVLOVCC + 250 mV
VIN-VCC dropout voltage
VCC output impedance
(0 mA ≤ ICC ≤ 5 mA)
VIN = 8V
VIN = 40V
VCC = 0V
155
0.16
11
Ω
VCC current limit(3)
mA
V
UVLOVCC
VCC under-voltage lockout
threshold
VCC increasing
5.7
UVLOVCC hysteresis
UVLOVCC filter delay
IIN operating current
IIN shutdown current
VCC decreasing
150
3
mV
µs
100 mV overdrive
Non-switching, FB = 3V
RON/SD = 0V
0.57
80
0.85
160
mA
µA
(1) For detailed information on soldering plastic WSON packages, visit www.ti.com/packaging.
(2) Typical specifications represent the most likely parametric norm at 25°C operation.
(3) VCC provides self bias for the internal gate drive and control circuits. Device thermal limitations limit external loading
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
Electrical Characteristics (continued)
Limits in standard type are for TJ = 25°C only; limits in boldface type apply over the junction temperature (TJ) range of -40°C
to +125°C. Minimum and Maximum limits are specified through test, design, or statistical correlation. Typical values represent
the most likely parametric norm at TJ = 25°C, and are provided for reference purposes only. Unless otherwise stated the
following conditions apply: VIN = 12V, RON = 200kΩ(1)(2)
.
Symbol
Parameter
Conditions
Min
Typ
Max
Units
Switch Characteristics
Rds(on)
UVLOGD
Buck Switch Rds(on)
Gate Drive UVLO
UVLOGD hysteresis
ITEST = 200 mA
0.33
4.2
0.7
5.5
Ω
V
VBST - VSW Increasing
3.0
470
mV
Softstart Pin
VSS
ISS
Pull-up voltage
2.5
V
Internal current source
12.5
µA
Current Limit
ILIM
VIN = 8V, VFB = 2.4V
VIN = 30V, VFB = 2.4V
VIN = 30V, VFB = 1.0V
1.0
0.9
1.2
1.1
1.4
1.3
Threshold
A
0.85
1.05
150
1.25
Response time
ns
On Timer
tON - 1
On-time (normal operation)
On-time (normal operation)
On-time (current limit)
VIN = 10V, RON = 200 kΩ
VIN = 40V, RON = 200 kΩ
VIN = 10V, RON = 200 kΩ
2.1
0.4
2.8
655
1.13
0.8
3.4
1.2
µs
ns
µs
V
tON - 2
tON - 3
Shutdown threshold at RON/SD Voltage at RON/SD rising
Shutdown Threshold hysteresis Voltage at RON/SD falling
32
mV
Off Timer
tOFF
Minimum Off-time
265
ns
Regulation and Over-Voltage Comparators (FB Pin)
VREF
FB regulation threshold
FB over-voltage threshold
FB bias current
SS pin = steady state
2.445
2.50
2.9
15
2.550
V
V
nA
Thermal Shutdown
TSD
Thermal shutdown temperature Junction temperature rising
Thermal shutdown hysteresis
175
20
°C
°C
Thermal Resistance
θJA
Junction to Ambient
30
8
°C/W
°C/W
0 LFPM Air Flow(4)
Junction to Case(4)
θJC
(4) Value shown assumes a 4-layer PC board and 4 vias to conduct heat from beneath the package.
4
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
Typical Performance Characteristics
Unless otherwise specified the following conditions apply: TJ = 25°C
Typical Efficiency Performance
VCC vs VIN
100
95
7.5
7.0
6.5
6.0
5.5
5.0
Vin = 8V
12V
24V
40V
90
85
80
75
70
V
= 5V
OUT
F
S
= 275 kHz
0
200
400
600
800
1000
6.5
7.0
7.5
8.0
(V)
8.5
9.0
LOAD CURRENT (mA)
V
IN
Figure 1.
VCC vs ICC
V
Figure 2.
ON-Time vs VIN and RON
8
7
6
5
4
3
2
1
0
10
400k
200k
600k
10V
IN í
V
= 9V
IN
3.0
1.0
V
= 8V
IN
100k
0.3
0.1
V
Externally Loaded
CC
R
= 45k
ON
F
= 200 kHZ
S
0
10
20
(V)
30
40
0
2
4
8
10
12
6
V
I
(mA)
IN
CC
Figure 3.
Figure 4.
Valley Current Limit Threshold
vs. FB and VIN
Voltage at the RON/SD Pin
= 45k
3.0
2.0
1.3
1.2
1.1
1.0
0.9
R
ON
V
= 8V
IN
100k
500k
15V
24V
34V
1.0
0
40V
0
10
20
(V)
30
40
0
0.5
1.0
1.5
(V)
2.0
2.5
V
IN
V
FB
Figure 5.
Figure 6.
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
5
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
Typical Performance Characteristics (continued)
Unless otherwise specified the following conditions apply: TJ = 25°C
Input Shutdown and Operating Current Into VIN
800
600
400
200
0
Operating Current
Shutdown Current
0
10
20
(V)
30
40
V
IN
Figure 7.
6
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
Typical Application Circuit and Block Diagram
7V START-UP
REGULATOR
LM34914
Input
VIN
VCC
8V - 40V
C5
C1
V
CC
THERMAL
SHUTDOWN
C3
UVLO
ON TIMER
GND
0.8V
MINIMUM
OFF TIMER
R
ON
R
ON
START
D Ton FINISH
RON/SD
FINISH
START
BST
SD
Gate Drive
UVLO
V
IN
2.5V
C4
12.5 mA
LOGIC
SS
FB
LEVEL
SHIFT
L1
Driver
C6
SW
V
OUT
REGULATION
COMPARATOR
D1
R1
R2
R3
C2
OVER-VOLTAGE
COMPARATOR
CURRENT LIMIT
COMPARATOR
2.9V
+
RTN
ISEN
-
R
SENSE
V
CL
Threshold
Adjust
-
+
IN
41 mW
FB
SGND
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
V
IN
7.0V
UVLO
V
CC
SW Pin
Inductor
Current
2.5V
SS Pin
V
OUT
t1
t2
Figure 8. Startup Sequence
Functional Description
The LM34914 Step Down Switching Regulator features all the functions needed to implement a low cost, efficient
buck bias power converter capable of supplying at least 1.25A to the load. This high voltage regulator contains
an N-Channel buck switch, is easy to implement, and is available in the thermally enhanced 3mm x 3mm WSON-
10 package. The regulator’s operation is based on a constant on-time control scheme where the on-time is
determined by VIN. This feature results in the operating frequency remaining relatively constant with load and
input voltage variations. The feedback control scheme requires no loop compensation resulting in very fast load
transient response. The valley current limit scheme protects against excessively high currents if the output is
short circuited when VIN is high. To aid in controlling excessive switch current due to a possible saturating
inductor the valley current limit threshold changes with input and output voltages, and the on-time is reduced by
approximately 50% when current limit is detected.The LM34914 can be applied in numerous applications to
efficiently regulate down higher voltages. Additional features include: Thermal shutdown, VCC under-voltage lock-
out, gate drive under-voltage lock-out, and maximum duty cycle limit.
Control Circuit Overview
The LM34914 buck DC-DC regulator employs a control scheme based on a comparator and a one-shot on-timer,
with the output voltage feedback (FB) compared to an internal reference (2.5V). If the FB voltage is below the
reference the buck switch is switched on for a time period determined by the input voltage and a programming
resistor (RON). Following the on-time the switch remains off until the FB voltage falls below the reference, but not
less than the minimum off-time forced by the LM34914. The buck switch is then turned on for another on-time
period.
8
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
When in regulation, the LM34914 operates in continuous conduction mode at heavy load currents and
discontinuous conduction mode at light load currents. In continuous conduction mode the inductor’s current is
always greater than zero, and the operating frequency remains relatively constant with load and line variations.
The minimum load current for continuous conduction mode is one-half the inductor’s ripple current amplitude.
The approximate operating frequency is calculated as follows:
VOUT x (VIN œ 1.5)
1.15 x 10-10 x (RON + 1.4k) x VIN
FS =
(1)
The buck switch duty cycle is equal to:
VOUT
VIN
tON
DC =
= tON x FS =
tON + tOFF
(2)
In discontinuous conduction mode, where the inductor’s current reaches zero during the off-time forcing a longer-
than-normal off-time, the operating frequency is lower than in continuous conduction mode, and varies with load
current. Conversion efficiency is maintained at light loads since the switching losses decrease with the reduction
in load and frequency. The approximate discontinuous operating frequency can be calculated as follows:
VOUT2 x L1 x 1.5 x 1020
FS =
2
RL x RON
(3)
where RL = the load resistance, and L1 is the circuit’s inductor.
The output voltage is set by the two feedback resistors (R1, R2 in the Block Diagram). The regulated output
voltage is calculated as follows:
VOUT = 2.5 x (R1 + R2) / R2
(4)
Output voltage regulation is based on supplying ripple voltage to the feedback input (FB pin), normally obtained
from the output voltage ripple through the feedback resistors. The LM34914 requires a minimum of 25 mVp-p of
ripple voltage at the FB pin, requiring the ripple voltage at VOUT be higher by the gain factor of the feedback
resistor ratio. The output ripple voltage is created by the inductor’s ripple current passing through R3 which is in
series with the output capacitor. For applications where reduced ripple is required at VOUT, see Applications
Information.
If the voltage at FB rises above 2.9V, due to a transient at VOUT or excessive inductor current which creates
higher than normal ripple at VOUT, the internal over-voltage comparator immediately shuts off the internal buck
switch. The next on-time starts when the voltage FB falls below 2.5V and the inductor current falls below the
current limit threshold.
ON-Time Timer
The on-time for the LM34914 is determined by the RON resistor and the input voltage (VIN), calculated from:
1.15 x 10-10 x (RON + 1.4k)
+ 50 ns
tON
=
(VIN - 1.5)
(5)
The inverse relationship with VIN results in a nearly constant frequency as VIN is varied. To set a specific
continuous conduction mode switching frequency (FS), the RON resistor is determined from the following:
VOUT x (VIN - 1.5)
FS x 1.15 x 10-10 x VIN
- 1.4k
RON
=
(6)
Equation 1, Equation 5, and Equation 6 are valid only during normal operation - i.e., the circuit is not in current
limit. When the LM34914 operates in current limit, the on-time is reduced by approximately 50%. This feature
reduces the peak inductor current which may be excessively high if the load current and the input voltage are
simultaneously high. This feature operates on a cycle-by-cycle basis until the load current is reduced and the
output voltage resumes its normal regulated value.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
Shutdown
The LM34914 can be remotely shut down by taking the RON/SD pin below 0.8V. See Figure 9. In this mode the
SS pin is internally grounded, the on-timer is disabled, and bias currents are reduced. Releasing the RON/SD pin
allows the circuit to resume operation. The voltage at the RON/SD pin is normally between 1.5V and 3.0V,
depending on VIN and the RON resistor.
V
IN
Input
Voltage
LM34914
R
ON
RON/SD
STOP
RUN
Figure 9. Shutdown Implementation
Current Limit
Current limit detection occurs during the off-time by monitoring the recirculating current flowing out of the ISEN
pin. Referring to the Typical Application Circuit and Block Diagram, during the off-time the inductor current flows
through the load, into SGND, through the internal sense resistor, out of ISEN and through D1 to the inductor. If
that current exceeds the current limit threshold the current limit comparator output delays the start of the next on-
time period. The next on-time starts when the current out of ISEN is below the threshold and the voltage at FB
falls below 2.5V. The operating frequency is typically lower due to longer-than-normal off-times.
The valley current limit threshold is a function of the input voltage (VIN) and the output voltage sensed at FB, as
shown in the graph “Valley Current Limit Threshold vs. VFB and VIN”. This feature reduces the inductor current’s
peak value at high line and load. To further reduce the inductor’s peak current, the next cycle’s on-time is
reduced by approximately 50% if the voltage at FB is below its threshold when the inductor current reduces to
the current limit threshold (VOUT is low due to current limiting).
Figure 10 illustrates the inductor current waveform during normal operation and in current limit. During the first
“Normal Operation” the load current is IOUT1, the average of the ripple waveform. As the load resistance is
reduced, the inductor current increases until it exceeds the current limit threshold. During the “Current Limited”
portion of Figure 10, the current limit threshold lowers since the high load current causes VOUT (and the voltage
at FB) to reduce. The on-time is reduced by approximately 50%, resulting in lower ripple amplitude for the
inductor’s current. During this time the LM34914 is in a constant current mode, with an average load current
equal to the current limit threshold + ΔI/2 (IOUT2). Normal operation resumes when the load current is reduced to
IOUT3, allowing VOUT, the current limit threshold, and the on-time to return to their normal values. Note that in the
second period of “Normal Operation”, even though the inductor’s peak current exceeds the current limit threshold
during part of each cycle, the circuit is not in current limit since the current falls below the threshold before the
feedback voltage reduces to its threshold.
The peak current allowed through the buck switch, and the ISEN pin, is 2A, and the maximum allowed average
current is 1.5A.
10
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
I
OUT2
Current Limit
Threshold
I
OUT3
DI
T
ON
2
I
OUT1
T
ON
2.5V
Normal
Operation
Current
Limited
Normal
Operation
Load
Current
Increases
Load Current
Decreases
Figure 10. Inductor Current - Normal and Current Limit Operation
N - Channel Buck Switch and Driver
The LM34914 integrates an N-Channel buck switch and associated floating high voltage gate driver. The gate
driver circuit works in conjunction with an external bootstrap capacitor and an internal high voltage diode. A 0.022
µF capacitor (C4) connected between BST and SW provides the voltage to the driver during the on-time. During
each off-time, the SW pin is at approximately -1V, and C4 is recharged for the next on-time from VCC through the
internal diode. The minimum off-time ensures a minimum time each cycle to recharge the bootstrap capacitor.
Softstart
The softstart feature allows the converter to gradually reach a steady state operating point, thereby reducing
start-up stresses and current surges. Upon turn-on, after VCC reaches the under-voltage threshold, an internal
12.5 µA current source charges up the external capacitor at the SS pin to 2.5V (t2 in Figure 8). The ramping
voltage at SS (and the non-inverting input of the regulation comparator) ramps up the output voltage in a
controlled manner.
An internal switch grounds the SS pin if VCC is below the under-voltage lockout threshold, or if the RON/SD pin is
grounded.
Thermal Shutdown
The LM34914 should be operated so the junction temperature does not exceed 125°C. If the junction
temperature increases above that, an internal Thermal Shutdown circuit activates (typically) at 175°C, taking the
controller to a low power reset state by disabling the buck switch and the on-timer. This feature helps prevent
catastrophic failures from accidental device overheating. When the junction temperature reduces below 155°C
(typical hysteresis = 20°C), normal operation resumes.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
APPLICATIONS INFORMATION
EXTERNAL COMPONENTS
The following guidelines can be used to select the external components (see the Block Diagram). First determine
the following operating parameters:
- Output voltage (VOUT
)
- Minimum and maximum input voltage (VIN(min) and VIN(max)
)
- Minimum and maximum load current (IOUT(min) and IOUT(max)
)
- Switching Frequency (FS)
R1 and R2: These resistors set the output voltage. The ratio of these resistors is calculated from:
R1/R2 = (VOUT/2.5V) - 1
(7)
R1 and R2 should be chosen from standard value resistors in the range of 1.0 kΩ - 10 kΩ which satisfy the
above ratio.
RON: The resistor sets the on-time, and consequently, the switching frequency. Its value can be determined using
Equation 6 based on the frequency, or Equation 5 if a specific on-time is required. The minimum allowed value
for RON is calculated from:
100 ns x (VIN(MAX) œ 1.5V)
- 1.4 kW
RON
í
1.15 x 10-10
(8)
L1: The main parameter affected by the inductor is the output current ripple amplitude (IOR). The minimum load
current is used to determine the maximum allowable ripple. In order to maintain continuous conduction mode the
valley should not reach 0 mA. This is not a requirement of the LM34914, but serves as a guideline for selecting
L1. For this case, the maximum ripple current is:
IOR(MAX) = 2 x IOUT(min)
(9)
If the minimum load current is zero, use 20% of IOUT(max) for IOUT(min) in Equation 9. The ripple calculated in
Equation 6 is then used in the following equation:
VOUT x (VIN (max) - VOUT
)
L1 =
IOR (max) x FS x VIN (max)
(10)
where Fs is the switching frequency. This provides a minimum value for L1. The next larger standard value
should be used, and L1 should be rated for the peak current level, equal to IOUT(max) + IOR(max)/2.
C2 and R3: Since the LM34914 requires a minimum of 25 mVp-p of ripple at the FB pin for proper operation, the
required ripple at VOUT is increased by R1 and R2. This necessary ripple is created by the inductor ripple current
flowing through R3, and to a lesser extent by C2 and its ESR. The minimum inductor ripple current is calculated
using Equation 10, rearranged to solve for IOR at minimum VIN.
VOUT x (VIN (min) - VOUT
)
IOR (min)
=
L1 x FS x VIN (min)
(11)
The minimum value for R3 is then equal to:
25 mV x (R1 + R2)
R3(min)
=
R2 x IOR (min)
(12)
Typically R3 is less than 5Ω. C2 should generally be no smaller than 3.3 µF, although that is dependent on the
frequency and the desired output characteristics. C2 should be a low ESR good quality ceramic capacitor.
Experimentation is usually necessary to determine the minimum value for C2, as the nature of the load may
require a larger value. A load which creates significant transients requires a larger value for C2 than a non-
varying load.
12
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
D1: A Schottky diode is recommended. Ultra-fast recovery diodes are not recommended as the high speed
transitions at the SW pin may inadvertently affect the IC’s operation through external or internal EMI. The diode
should be rated for the maximum input voltage (VIN(max)), the maximum load current (IOUT(max)), and the peak
current which occurs when the current limit and maximum ripple current are reached simultaneously. The diode’s
average power dissipation is calculated from:
PD1 = VF x IOUT x (1-D)
(13)
where VF is the diode's forward voltage drop, and D is the duty cycle.
C1 and C5: C1’s purpose is to supply most of the switch current during the on-time, and limit the voltage ripple
at VIN, on the assumption that the voltage source feeding VIN has an output impedance greater than zero. If the
source’s dynamic impedance is high (effectively a current source), it supplies the average input current, but not
the ripple current.
At maximum load current, when the buck switch turns on, the current into VIN suddenly increases to the lower
peak of the inductor’s ripple current, ramps up to the upper peak, then drop to zero at turn-off. The average
current during the on-time is the load current. For a worst case calculation, C1 must supply this average load
current during the maximum on-time. C1 is calculated from:
IOUT (max) x tON
C1 =
DV
(14)
where tON is the maximum on-time, and ΔV is the allowable ripple voltage at VIN. C5’s purpose is to help avoid
transients and ringing due to long lead inductance leading to the VIN pin. A low ESR, 0.1 µF ceramic chip
capacitor is recommended, and must be located close to the VIN and RTN pins.
C3: The capacitor at the VCC output provides not only noise filtering and stability, but also prevents false
triggering of the VCC UVLO at the buck switch on/off transitions. C3 should be no smaller than 0.1 µF, and should
be a good quality, low ESR, ceramic capacitor. C3’s value, and the VCC current limit, determine a portion of the
turn-on-time (t1 in Figure 8).
C4: The recommended value for C4 is 0.022 µF. A high quality ceramic capacitor with low ESR is recommended
as C4 supplies a surge current to charge the buck switch gate at turn-on. A low ESR also helps ensure a
complete recharge during each off-time.
C6: The capacitor at the SS pin determines the softstart time, i.e. the time for the output voltage, to reach its final
value (t2 in Figure 8). The capacitor value is determined from the following:
t2 x 12.5 mA
C6 =
2.5V
(15)
PC BOARD LAYOUT
The LM34914 regulation, over-voltage, and current limit comparators are very fast, and respond to short duration
noise pulses. Layout considerations are therefore critical for optimum performance. The layout must be as neat
and compact as possible, and all of the components must be as close as possible to their associated pins. The
current loop formed by D1, L1, C2 and the SGND and ISEN pins should be as small as possible. The ground
connection from SGND and RTN to C1 should be as short and direct as possible.
If it is expected that the internal dissipation of the LM34914 will produce excessive junction temperatures during
normal operation, good use of the PC board’s ground plane can help to dissipate heat. The exposed pad on the
bottom of the IC package can be soldered to a ground plane, and that plane should extend out from beneath the
IC, and be connected to ground plane on the board’s other side with several vias, to help dissipate the heat. The
exposed pad is internally connected to the IC substrate. Additionally the use of wide PC board traces, where
possible, can help conduct heat away from the IC. Judicious positioning of the PC board within the end product,
along with the use of any available air flow (forced or natural convection) can help reduce the junction
temperatures.
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
LOW OUTPUT RIPPLE CONFIGURATIONS
For applications where low output ripple is required, the following options can be used to reduce or nearly
eliminate the ripple.
a) Reduced ripple configuration: In Figure 11, Cff is added across R1 to AC-couple the ripple at VOUT directly
to the FB pin. This allows the ripple at VOUT to be reduced to a minimum of 25 mVp-p by reducing R3, since the
ripple at VOUT is not attenuated by the feedback resistors. The minimum value for Cff is determined from:
tON (max)
Cff =
(R1//R2)
(16)
where tON(max) is the maximum on-time, which occurs at VIN(min). The next larger standard value capacitor should
be used for Cff. R1 and R2 should each be towards the upper end of the 1kΩ to 10kΩ range.
L1
SW
V
OUT
Cff
LM34914
R1
R3
FB
R2
C2
Figure 11. Reduced Ripple Configuration
b) Minimum ripple configuration: If the application requires a lower value of ripple (<10 mVp-p), the circuit of
Figure 12 can be used. R3 is removed, and the resulting output ripple voltage is determined by the inductor’s
ripple current and C2’s characteristics. RA and CA are chosen to generate a sawtooth waveform at their junction,
and that voltage is AC-coupled to the FB pin via CB. To determine the values for RA, CA and CB, use the
following procedure:
Calculate VA = VOUT - (VSW x (1 - (VOUT/VIN(min))))
(17)
where VSW is the absolute value of the voltage at the SW pin during the off-time (typically 1V). VA is the DC
voltage at the RA/CA junction, and is used in the next equation.
Calculate RA x CA = (VIN(min) - VA) x tON/ΔV
(18)
where tON is the maximum on-time (at minimum input voltage), and ΔV is the desired ripple amplitude at the
RA/CA junction (typically 40-50 mV). RA and CA are then chosen from standard value components to satisfy the
above product. Typically CA is 1000 pF to 5000 pF, and RA is 100kΩ to 300 kΩ. CB is then chosen large
compared to CA, typically 0.1 µF. R1 and R2 should each be towards the upper end of the 1kΩ to 10kΩ range.
L1
SW
V
OUT
CA
C2
LM34914
RA
CB
R1
R2
FB
Figure 12. Minimum Output Ripple Using Ripple Injection
14
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
LM34914
www.ti.com
SNVS453B –MAY 2006–REVISED MARCH 2013
c) Alternate minimum ripple configuration: The circuit in Figure 13 is the same as that in the Block Diagram,
except the output voltage is taken from the junction of R3 and C2. The ripple at VOUT is determined by the
inductor’s ripple current and C2’s characteristics. However, R3 slightly degrades the load regulation. This circuit
may be suitable if the load current is fairly constant.
L1
SW
LM34914
R1
R2
R3
FB
V
OUT
C2
Figure 13. Alternate Minimum Output Ripple
Copyright © 2006–2013, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Links: LM34914
LM34914
SNVS453B –MAY 2006–REVISED MARCH 2013
www.ti.com
REVISION HISTORY
Changes from Revision A (March 2013) to Revision B
Page
•
Changed layout of National Data Sheet to TI format .......................................................................................................... 15
16
Submit Documentation Feedback
Copyright © 2006–2013, Texas Instruments Incorporated
Product Folder Links: LM34914
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
LM34914SD/NOPB
ACTIVE
WSON
DSC
10
1000 RoHS & Green
SN
Level-1-260C-UNLIM
-40 to 125
34914
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Oct-2021
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
LM34914SD/NOPB
WSON
DSC
10
1000
178.0
12.4
3.3
3.3
1.0
8.0
12.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
21-Oct-2021
*All dimensions are nominal
Device
Package Type Package Drawing Pins
WSON DSC 10
SPQ
Length (mm) Width (mm) Height (mm)
208.0 191.0 35.0
LM34914SD/NOPB
1000
Pack Materials-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATA SHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, regulatory or other requirements.
These resources are subject to change without notice. TI grants you permission to use these resources only for development of an
application that uses the TI products described in the resource. Other reproduction and display of these resources is prohibited. No license
is granted to any other TI intellectual property right or to any third party intellectual property right. TI disclaims responsibility for, and you
will fully indemnify TI and its representatives against, any claims, damages, costs, losses, and liabilities arising out of your use of these
resources.
TI’s products are provided subject to TI’s Terms of Sale or other applicable terms available either on ti.com or provided in conjunction with
such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable warranties or warranty disclaimers for
TI products.
TI objects to and rejects any additional or different terms you may have proposed. IMPORTANT NOTICE
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2023, Texas Instruments Incorporated
相关型号：
LM34917A
Ultra Small 33V, 1.25A Constant On-Time Buck Switching Regulator with Intelligent Current Limit
NSC
LM34917ATL
Ultra Small 33V, 1.25A Constant On-Time Buck Switching Regulator with Intelligent Current Limit
NSC
LM34917ATLX
Ultra Small 33V, 1.25A Constant On-Time Buck Switching Regulator with Intelligent Current Limit
NSC
©2020 ICPDF网 联系我们和版权申明