THS770006_10 [TI]
Broadband, Fully-Differential, 14-/16-Bit ADC DRIVER AMPLIFIER; 宽带全差动, 14位/ 16位ADC驱动器放大器型号: | THS770006_10 |
厂家: | TEXAS INSTRUMENTS |
描述: | Broadband, Fully-Differential, 14-/16-Bit ADC DRIVER AMPLIFIER |
文件: | 总36页 (文件大小:1005K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
THS770006
www.ti.com
SBOS520 –JULY 2010
Broadband, Fully-Differential, 14-/16-Bit
ADC DRIVER AMPLIFIER
Check for Samples: THS770006
1
FEATURES
DESCRIPTION
23
•
2.4GHz Bandwidth
The THS770006 is a fixed-gain of +6dB, wideband,
fully-differential amplifier designed and optimized
specifically for driving 16-bit analog-to-digital
converters (ADCs) at input frequencies up to
130MHz, and 14-bit ADCs at input frequencies up to
200MHz. This device provides high bandwidth,
high-voltage output with low distortion and low noise,
critical in high-speed data acquisition systems that
require very high dynamic range, such as wireless
base stations and test and measurement
applications. This device also makes an excellent
differential amplifier for general-purpose, high-speed
differential signal chain and short line driver
applications.
•
3100V/µs Slew Rate, VOUT =2V step
Fixed Voltage Gain: +6dB
•
•
IMD3: –107dBc, VOUT = 2VPP, RL = 400Ω,
f = 100MHz
•
•
OIP3: 48dBm, f = 100MHz
Noise Figure: 11dB, f = 100MHz
APPLICATIONS
•
•
14/16-bit ADC Driver
ADC Driver for Wireless Base Station Signal
Chains: GSM, WCDMA, MC-GSM
•
ADC Driver for High Dynamic Range Test and
Measurement Equipment
The THS7700 operates on a nominal +5V single
supply, offers very fast, 7.5ns maximum recovery
time from overdrive conditions, and has
power-down mode for power saving. The THS770006
is offered in a Pb-free (RoHS compliant) and green,
a
THS770006 Driving ADS5493
100W
QFN-24
thermally-enhanced
package.
It
is
characterized for operation over the industrial
temperature range of –40°C to +85°C.
RO
50W
AIN+
VIN-
VIN+
30MHz
Bandpass
Filter
VOCM
ADS5493
AIN-
RO
50W
RELATED DEVICES
100W
VOCM
DEVICE
DESCRIPTION
THS770006
Wideband, low-noise, low-distortion,
fully-differential amplifier
THS4509
Wideband, low-noise, low-distortion,
fully-differential, digitally-programmable
gain amplifier
FFT Plot with Two-Tone Input at 96MHz and
PGA870
100MHz (see Application Information section).
10
0
ADS5481 to
ADS5485
16-bit, 80MSPS to 200MSPS ADCs
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
130
140
ADS5493
ADS6145
ADS6149
16-bit, 130MSPS ADC
14-bit, 125MSPS ADC
14-bit, 250MSPS ADC
0
5
10 15 20 25 30 35 40 45 50 55
Frequency (MHz)
61
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PowerPAD is a trademark of Texas Instruments.
2
3
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2010, Texas Instruments Incorporated
THS770006
SBOS520 –JULY 2010
www.ti.com
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
PACKAGE/ORDERING INFORMATION(1)
SPECIFIED
TEMPERATURE
RANGE
PACKAGE
TYPE
PACKAGE
DESIGNATOR
PACKAGE
MARKING
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
THS770006IGRE THS770006IRGET
Tape and reel, 250
THS770006
VQFN-24
RGE
–40°C to +85°C
THS770006IGRE THS770006IRGER Tape and reel, 3000
(1) For the most current package and ordering information see the Package Option Addendum at the end of this document, or visit the
device product folder on www.ti.com.
DEVICE MARKING INFORMATION
= Pin 1 designator
THS7700
THS770006IRGE = device name
06IRGE
TI = TI LETTERS
YM = YEAR MONTH DATE CODE
TI YMS
S = ASSEMBLY SITE CODE
LLLL = ASSY LOT CODE
LLLL
ABSOLUTE MAXIMUM RATINGS(1)
Over operating free-air temperature range, unless otherwise noted.
THS770006
UNIT
V
Power supply (VS+ to GND)
5.5
Ground to VS+
Ground to VS+
10
Input voltage range
V
Differential input voltage, VID
V
Continuous input current, II
mA
mA
°C
°C
°C
V
Continuous output current, IO
100
Storage temperature range, Tstg
Maximum junction temperature, TJ
Maximum junction temperature, continuous operation, long term reliability
Human body model (HBM)
–40°C to +125°C
+150
+125
2500
ESD ratings
Charged device model (CDM)
Machine model (MM)
1000
V
100
V
(1) Stresses above these ratings may cause permanent damage. Exposure to absolute maximum conditions for extended periods may
degrade device reliability. These are stress ratings only, and functional operation of the device at these or any other conditions beyond
those specified is not implied.
2
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
THERMAL INFORMATION
THS770006
RGE
24 PINS
44.1
THERMAL METRIC(1)
UNITS
qJA
Junction-to-ambient thermal resistance
qJC(top)
qJB
Junction-to-case(top) thermal resistance
Junction-to-board thermal resistance
35
19
°C/W
yJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case(bottom) thermal resistance
0.5
yJB
18.8
qJC(bottom)
8.9
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
ELECTRICAL CHARACTERISTICS
Test conditions are at TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input
and output, and input and output referenced to midsupply, unless otherwise noted. Measured using evaluation module as
discussed in Test Circuits section.
TEST
PARAMETER
AC PERFORMANCE
Small-signal bandwidth
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LEVEL(1)
VOUT = 200mVPP
VOUT = 2VPP
2.4
675
485
360
325
GHz
MHz
MHz
MHz
MHz
V/µs
V/µs
ns
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
C
Large-signal bandwidth
Bandwidth for 0.1dB flatness
Slew rate
VOUT = 3VPP
VOUT = 2VPP
VOUT = 3VPP
VOUT = 2V step
VOUT = 4V step
VOUT = 2V step
VOUT = 2V step
VOUT = 2V step
3100
3200
0.6
Rise time
Fall time
0.6
ns
Settling time to 0.1%
Input return loss, s11
Output return loss, s22
Reverse isolation, s12
2.2
ns
See s-Parameters section, f < 200MHz
See s-Parameters section, f < 200MHz
See s-Parameters section, f < 200MHz
f = 10MHz
–20
–20
–70
–87
–81
–78
–74
–103
–91
–86
–77
–80
–79
–77
–76
–107
–107
–97
–82
19.6
8.7
dB
dB
dB
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBc
dBm
dBm
f = 50MHz
Second-order harmonic
distortion
f = 100MHz
f = 200MHz
f = 10MHz
f = 50MHz
Third-order harmonic distortion
f = 100MHz
f = 200MHz
f = 50MHz, 10MHz spacing
f = 100MHz, 10MHz spacing
f = 150MHz, 10MHz spacing
f = 200MHz, 10MHz spacing
f = 50MHz, 10MHz spacing
f = 100MHz, 10MHz spacing
f = 150MHz, 10MHz spacing
f = 200MHz, 10MHz spacing
Second-order intermodulation
distortion
Third-order intermodulation
distortion
RL = 20Ω
f = 100MHz
1dB compression point
RL = 400Ω
(1) Test levels: (A) 100% tested at +25°C. Over-temperature limits by characterization and simulation. (B) Limits set by characterization and
simulation. (C) Typical value only for information.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
Test conditions are at TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input
and output, and input and output referenced to midsupply, unless otherwise noted. Measured using evaluation module as
discussed in Test Circuits section.
TEST
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LEVEL(1)
Output third-order intercept
point
At device outputs, RL = 400Ω, f = 100MHz
48
dBm
C
Input-referred voltage noise
Ouput-referred voltage noise
f > 100kHz
f > 100kHz
f = 50 MHz
100Ω differential
f = 100 MHz
source
f = 200 MHz
Overdrive = ±0.5V
f = 200MHz
1.7
3.4
10.5
11
nV/√Hz
nV/√Hz
dB
C
C
C
C
C
B
C
C
Noise figure
dB
13
dB
Overdrive recovery
Output balance error
Output impedance
DC PERFORMANCE
5
7.5
ns
-60
4.4
dB
f = 100MHz
Ω
TA = +25°C, RL = 400Ω
TA = +25°C, RL = 100Ω
TA = –40°C to +85°C, RL = 400Ω
TA = –40°C to +85°C, RL = 100Ω
TA = +25°C
5.75
6
6.25
5.9
dB
dB
dB
dB
mV
mV
dB
dB
A
B
B
B
A
B
A
B
5.5
5.7
5.7
Gain
6.3
5.45
–10
–12.5
36
5.95
10
±1
60
Output offset
TA = –40°C to +85°C
TA = +25°C
12.5
Common-mode rejection ratio
TA = –40°C to +85°C
35
INPUT
Differential input resistance
Input common-mode range
OUTPUT
85
100
115
Ω
A
A
Inputs shorted together, VOCM = 2.5V
2.25
2.75
V
TA = +25°C
3.64
3.59
3.7
1.3
V
V
A
B
A
B
A
B
A
B
B
B
B
B
Each output with
200Ω to midsupply
Most positive output voltage
Least positive output voltage
Most positive output voltage
Least positive output voltage
Differential output voltage
TA = –40°C to +85°C
TA = +25°C
1.4
V
Each output with
200Ω to midsupply
TA = –40°C to +85°C
1.45
V
TA = +25°C
3.59
3.54
3.6
V
Each output with
50Ω to midsupply
TA = –40°C to +85°C
V
TA = +25°C
1.3
1.5
V
Each output with
50Ω to midsupply
TA = –40°C to +85°C
1.55
V
TA = +25°C, RL = 400Ω
4.4
4.2
4.85
VPP
VPP
mA
mA
TA = –40°C to +85°C, RL = 400Ω
TA = +25°C, RL = 10Ω
80
80
Differential output current drive
TA = –40°C to +85°C, RL =10Ω
OUTPUT COMMON-MODE VOLTAGE CONTROL
VOCM small-signal bandwidth
VOCM slew rate
VOUT_CM = 200mVPP
VOUT_CM = 500mVPP
Supplied by external source(2)
VOCM = 2.5V
525
180
2.5
1
MHz
V/µs
V
C
C
C
A
VOCM voltage range
VOCM gain
2.25
0.98
2.75
1.02
V/V
Output common-mode offset
from VOCM input
VOCM = 2.5V
–30
12
30
mV
µA
A
A
VOCM input bias current
2.25V ≤ VOCM ≤ 2.75V
–400
±30
400
(2) Limits set by best harmonic distortion with VOUT = 3VPP. VOCM voltage range can be extended if lower output swing is used or distortion
degradation is allowed, and increased bias current into pin is acceptable. For more information, see Figure 12 and Figure 30.
4
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
ELECTRICAL CHARACTERISTICS (continued)
Test conditions are at TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input
and output, and input and output referenced to midsupply, unless otherwise noted. Measured using evaluation module as
discussed in Test Circuits section.
TEST
PARAMETER
POWER SUPPLY
TEST CONDITIONS
MIN
TYP
MAX
UNIT
LEVEL(1)
Specified operating voltage
4.75
5
5.25
V
C
A
B
A
B
TA = +25°C
85
80
60
59
100
115
125
mA
mA
dB
dB
Quiescent current
TA = –40°C to +85°C
TA = +25°C, VCC ±0.25V
TA = –40°C to +85°C, VCC ±0.5V
90
Power-supply rejection ratio
POWER-DOWN
Enable voltage threshold
Disable voltage threshold
Power-down quiescent current
Input bias current
Device powers on below 0.5V
0.5
V
V
A
A
A
A
C
C
Device powers down above 2.0V
2
0.8
80
3
mA
µA
µs
µs
100
Turn-on time delay
Time to VOUT = 90% of final value
Time to VOUT = 10% of original value
10
Turn-off time delay
0.15
THERMAL CHARACTERISTICS
Specified operating range
–40
+85
°C
C
C
C
(3)
Thermal resistance, qJC
Junction to case (bottom)
Junction to ambient
8.9
°C/W
°C/W
(3)
Thermal resistance, qJA
44.1
(3) Tested using JEDEC High-K test PCB. Thermal management of the final printed circuit board (PCB) should keep the junction
temperature below +125°C for long term reliability.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
PIN CONFIGURATION
RGE PACKAGE
VQFN-24
(TOP VIEW)
1
2
3
4
5
6
18 NC
17
NC
PD
100W
Unused
50W
16
15
VOUT+
VOUT-
VIN-
VIN+
VOCM
NC
VOCM
50W
100W
14 Unused
13
NC
PIN DESCRIPTIONS
PIN
NO.
NAME
DESCRIPTION
1
NC
PD
No internal connection
2
Power down. High = low power (sleep) mode. Low = active.
Inverting input pin
3
VIN–
VIN+
4
5
Noninverting input pin
VOCM Output common-mode voltage control input pin
NC No internal connection
GND Ground. Must be connected to thermal pad.
NC No internal connection
6, 7
8, 9, 10, 11
12, 13
14
Unused Bonded to die, but not used. Tie to GND.
VOUT– Inverting output pin
15
16
VOUT+ Noninverting output pin
17
Unused Bonded to die, but not used. Tie to GND.
18, 19
NC
VS+
NC
No internal connection
20, 21, 22,
23
Power supply pins, +5V nominal
No internal connection
24
Thermal pad
Thermal pad on bottom of device is used for heat dissipation and must be tied to GND
6
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
TYPICAL CHARACTERISTICS
TABLE OF GRAPHS
TITLE
FIGURE
Figure 1
Frequency Response Magnitude (with Transformers)
Frequency Response Magnitude (no Transformers)
Frequency Response Phase (no Transformers)
Small- and Large-Signal Pulse Response
Slew Rate vs Output Voltage Step
Figure 2
Figure 3
Figure 4
Figure 5
Overdrive Recovery
Figure 6
Single-Ended Input Harmonic Distortion vs Frequency
Harmonic Distortion vs Frequency, VOUT = 1VPP, 2VPP, 3VPP
Harmonic Distortion vs Frequency, VOUT = 0.9VPP
Harmonic Distortion vs VOUT
Figure 7
Figure 8
Figure 9
Figure 10
Figure 11
Figure 12
Figure 13
Figure 14
Figure 15
Figure 16
Figure 17
Figure 18
Figure 19
Figure 20
Figure 21
Figure 22
Figure 23
Figure 24
Figure 25
Figure 26
Figure 27
Figure 28
Figure 29
Figure 30
Figure 31
Harmonic Distortion vs RL
Harmonic Distortion vs VOCM
Intermodulation Distortion vs Frequency, VOUT = 2VPP, 3VPP Envelope
Intermodulation Distortion vs Frequency, VOUT = 0.9VPP Envelope
Output Intercept Point vs Frequency
Maximum Differential Output Voltage Swing Peak-to-Peak vs Differential Load Resistance
Maximum/Minimum Single-Ended Output Voltage vs Differential Load Resistance
Differential Output Impedance vs Frequency
s-Parameters (Magnitude)
Frequency Response vs Capacitive Load
Recommended RO vs Capacitive Load
Common-Mode Rejection Ratio vs Frequency
Power-Supply Rejection Ratio vs Frequency
VOCM Pulse Response
Turn-On Time
Turn-Off Time
Input and Output Voltage Noise vs Frequency
Output Balance Error vs Frequency
VOCM Small-Signal Frequency Response
VOCM Input Bias Current vs VOCM Input Voltage
Noise Figure vs Frequency
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
FREQUENCY RESPONSE MAGNITUDE
(WITH TRANSFORMERS)
FREQUENCY RESPONSE MAGNITUDE
(NO TRANSFORMERS)
12
9
9
6
VOUT = 200mVPP
Measured on EVM using transformers.
See Frequency Response: 200mVPP, 2VPP, 3VPP section.
6
3
3
0
0
-3
-6
-9
-12
VOUT = 2VPP
-3
-6
-9
Measured on EVM;
no transformers.
VO = 200mVPP
VO = 2VPP
VOUT = 3VPP
See Frequency Response:
200mVPP, 2VPP, 3VPP section.
VO = 3VPP
100k
1M
10M
100M
1G
10G
10M
100M
Frequency (Hz)
1G
10G
Frequency (Hz)
Figure 1.
Figure 2.
FREQUENCY RESPONSE PHASE
(NO TRANSFORMERS)
SMALL- AND LARGE-SIGNAL PULSE RESPONSE
45
3
2
0
-45
VOUT = 200mVPP
1
0
-90
-1
-2
-3
VOUT = 2VPP
Measured on EVM;
no transformers.
See Frequency Response:
-135
-180
VOUT = 3VPP
0.5V Step Input
2.5V Step Input
200mVPP, 2VPP, 3VPP section.
100k 1M 10M
100M
1G
10G
0
20
40
60
80
100
120
Frequency (Hz)
TIme (ns)
Figure 3.
Figure 4.
SLEW RATE
vs OUTPUT VOLTAGE STEP
OVERDRIVE RECOVERY
2.0
1.5
4
4000
3000
2000
1000
VIN
Differential VOUT
3
1.0
2
0.5
1
0
0
-0.5
-1.0
-1.5
-2.0
-1
-2
-3
-4
0
20
40
Time (ns)
60
80
100
0
1
2
3
4
5
VOUT (VPP
)
Figure 5.
Figure 6.
8
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
SINGLE-ENDED INPUT
HARMONIC DISTORTION vs FREQUENCY
HARMONIC DISTORTION vs FREQUENCY
VOUT = 1VPP, 2VPP, 3VPP
-60
-65
-60
-65
HD2, VOUT = 3VPP
RL = 400W
HD2, VOUT = 3VPP
HD2, VOUT = 2VPP
HD2, VOUT = 1VPP
RL = 400W
HD2, VOUT = 2VPP
HD2, VOUT = 1VPP
-70
-70
-75
-75
-80
-80
-85
-85
-90
-90
-95
-95
HD3, VOUT = 3VPP
HD3, VOUT = 3VPP
HD3, VOUT = 2VPP
HD3, VOUT = 1VPP
-100
-105
-110
-115
-100
-105
-110
-115
HD3, VOUT = 2VPP
HD3, VOUT = 1VPP
10M
100M
1G
1G
1k
10M
100M
1G
Frequency (Hz)
Frequency (Hz)
Figure 7.
Figure 8.
HARMONIC DISTORTION vs FREQUENCY
VOUT = 0.9VPP
HARMONIC DISTORTION
vs VOUT
-30
-40
-65
-70
-75
-80
-85
-90
-95
-100
RL = 400W
f = 100MHz
RL = 400W
VOUT = 0.9VPP
-50
HD2
-60
-70
HD3
HD2
-80
-90
HD3
-100
-110
100M
0
1
2
3
4
5
Frequency (Hz)
VOUT Differential (V)
Figure 9.
Figure 10.
HARMONIC DISTORTION
vs RL
HARMONIC DISTORTION
vs VOCM
-65
-70
-75
-80
-85
-90
-20
-30
f = 100MHz
VOUT = 3VPP
f = 100MHz
RL = 400W
-40
HD2, VOUT = 3VPP
HD3, VOUT = 3VPP
-50
-60
HD2
HD3
-70
-80
-90
HD3, VOUT = 2VPP
HD2, VOUT = 2VPP
-100
-110
0
200
400
600
800
2
2.25
2.5
2.75
3
RL (W)
VOCM (V)
Figure 11.
Figure 12.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
INTERMODULATION DISTORTION
INTERMODULATION DISTORTION
vs FREQUENCY, VOUT = 2VPP, 3VPP ENVELOPE
vs FREQUENCY, VOUT = 0.9VPP ENVELOPE
-65
-70
-30
-40
RL = 400W
IMD2, VOUT = 3VPP Envelope
IMD2, VOUT = 2VPP Envelope
RL = 400W
VOUT = 0.9VPP Envelope
-75
-50
-80
-60
IMD2
-85
-70
-90
-80
-95
IMD3
-90
-100
-105
-110
IMD3, VOUT = 3VPP Envelope
IMD3, VOUT = 2VPP Envelope
-100
-110
50M
75M
100M
125M
150M
175M
200M
100M
1G
Frequency (Hz)
Frequency (Hz)
Figure 13.
Figure 14.
OUTPUT INTERCEPT POINT
vs FREQUENCY
MAXIMUM DIFFERENTIAL OUTPUT VOLTAGE SWING
PEAK-TO-PEAK vs DIFFERENTIAL LOAD RESISTANCE
90
80
70
60
50
40
30
20
10
0
5.5
OIP2
5.0
Maximum
4.5
Differential
4.0
3.5
3.0
2.5
2.0
1.5
1.0
VOUT_PP
OIP3
RL = 400W
VOUT = 3VPP Envelope
50M
100M
150M
200M
10
100
1k
Frequency (Hz)
Load Resistance (W)
Figure 15.
Figure 16.
MAXIMUM/MINIMUM SINGLE-ENDED OUTPUT VOLTAGE
vs DIFFERENTIAL LOAD RESISTANCE
DIFFERENTIAL OUTPUT IMPEDANCE
vs FREQUENCY
4.0
1k
100
10
3.5
Maximum Single-Ended VOUT
3.0
2.5
2.0
Minimum Single-Ended VOUT
1.5
1.0
1
10
100
1k
1M
10M
100M
1G
10G
Load Resistance (W)
Frequency (Hz)
Figure 17.
Figure 18.
10
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
s-PARAMETERS
(MAGNITUDE)
FREQUENCY RESPONSE
vs CAPACITIVE LOAD
20
0
9
6
s22
-20
-40
-60
-80
-100
3
s11
s12
0
CL = 10pF, RO = 35W
CL = 24pF, RO = 18.7W
CL = 44pF, RO = 13W
CL = 94pF, RO = 8.2W
CL = 660pF, RO = 0.7W
-3
-6
1M
10M
100M
1G
10G
10M
100M
1G
10G
Frequency (Hz)
Frequency (Hz)
Figure 19.
Figure 20.
RECOMMENDED RO
vs CAPACITIVE LOAD
COMMON-MODE REJECTION RATIO
vs FREQUENCY
100
90
80
70
60
50
40
30
20
10
0
1k
100
10
1
1M
10M
100M
1G
1
10
100
1k
Frequency (Hz)
Capacitive Load (pF)
Figure 21.
Figure 22.
POWER-SUPPLY REJECTION RATIO
vs FREQUENCY
VOCM PULSE RESPONSE
100
90
80
70
60
50
40
30
20
10
0
3.0
2.9
2.8
2.7
2.6
2.5
2.4
2.3
2.2
2.1
2.0
10k
100k
1M
10M
100M
1G
0
50
100
150
200
250
300
350
400
Frequency (Hz)
Time (ns)
Figure 23.
Figure 24.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
TURN-ON TIME
TURN-OFF TIME
4
3
4
3
Power-Down
VOUT
2
2
1
1
0
0
VOUT
Power-Down
-1
-1
0
4
8
12
16
20
24 28
32 36
40
0
2
4
6
8
10
12 14
16 18
20
Time (ms)
Time (ms)
Figure 25.
Figure 26.
INPUT AND OUTPUT VOLTAGE NOISE
vs FREQUENCY
OUTPUT BALANCE ERROR
vs FREQUENCY
10
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
Output Noise
Input Noise
1
10k
100k
1M
10M
100M
1M
10M
100M
1G
10G
Frequency (Hz)
Frequency (Hz)
Figure 27.
Figure 28.
VOCM INPUT BIAS CURRENT
vs VOCM INPUT VOLTAGE
VOCM SMALL-SIGNAL FREQUENCY RESPONSE
3
0
200
VO = 200mVPP
150
100
50
-3
-6
0
-9
-50
-100
-150
-200
-12
-15
-18
1M
10M
100M
1G
2.1
2.3
2.5
2.7
2.9
Frequency (Hz)
VOCM Input Voltage (V)
Figure 29.
Figure 30.
12
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
TYPICAL CHARACTERISTICS (continued)
At TA = +25°C, VS+ = +5V, VOCM = +2.5V, VOUT = 2VPP, RL = 400Ω differential, G = +6dB, differential input and output, and
input and output pins referenced to midsupply, unless otherwise noted. Measured using EVM as discussed in Test Circuits
section.
NOISE FIGURE
vs FREQUENCY
20
100W Differential Source
18
16
14
12
10
8
6
4
2
0
10M
100M
200M
Frequency (Hz)
Figure 31.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TEST CIRCUITS
OVERVIEW
The standard THS770006 evaluation module (EVM) is used for testing the typical performance shown in the
Typical Characteristics, with changes as noted below. The EVM schematic is shown in Figure 32. The signal
generators and analyzers used for most tests have single-ended 50Ω input and output impedance. The
THS770006 EVM is configured to convert to and from a differential 50Ω impedance by using RF transformers or
baluns (CX2156NL from Pulse, supplied as a standard configuration of the EVM). For line input termination, two
49.9Ω resistors (R5 and R6) are placed to ground on the input transformer output pins (terminals 1 and 3). In
combination with the 100Ω input impedance of the device, the total impedance seen by the line is 50Ω.
A resistor network is used on the amplifier output to present various loads (RL) and maintain line output
termination to 50Ω. Depending on the test conditions, component values are changed as shown in Table 1, or as
otherwise noted. As a result of the voltage divider on the output formed by the load component values, the
amplifier output is attenuated. The Loss column in Table 1 shows the attenuation expected from the resistor
divider. The output transformer causes slightly more loss, so these numbers are approximate.
Table 1. Load Component Values(1)
LOAD RL
100Ω
R15 AND R17
25Ω
R16
LOSS
6dB
Open
69.8Ω
57.6Ω
52.3Ω
200Ω
86.6Ω
16.8dB
25.5dB
31.8dB
400Ω
187Ω
1kΩ
487Ω
(1) The total load includes 50Ω termination by the test equipment. Components are chosen to achieve load and 50Ω line termination
through a 1:1 transformer.
14
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Figure 32. THS770006IRGE EVM Schematic
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TEST DESCRIPTIONS
The following sections describe how the tests were performed, as well as the EVM circuit modifications that were
made (if any). Modifications made for test purposes include changing capacitors to resistors, resistors to
capacitors, the shorting/opening of components, etc., as noted. Unless otherwise noted, C1, C2, C9, and C13
are all changed to 0.1µF.
Frequency Response: 200mVPP, 2VPP, 3Vpp
This test is run with and without transformers in the signal path.
For tests with transformers, the standard EVM is used and only the gain magnitude is shown. A network analyzer
is connected to the input and output of the EVM with 50Ω coaxial cables and set to measure the forward transfer
function (s21). The input signal frequency is swept with the signal level set for the desired output amplitude. The
use of transformers gives better magnitude response that correlates best with detailed design simulation in terms
of peaking in the response due to better control of parasitic capacitance at the device output pins, but also
results in excess phase shift. So only magnitude is plotted.
For tests without transformers, the standard EVM is used, with the gain magnitude and phase shown. A network
analyzer is connected to the input of the EVM with 50Ω coaxial cable, the output is terminated with a 50Ω load,
and a high impedance differential probe is used for the measurement. The analyzer is set to measure the
forward transfer function (s21). The analyzer with a probe input is calibrated at the input pins of the device and
signal is measured at the output pin, thus effectively removing the transformers from the transfer function. The
input signal frequency is swept with signal level set for desired output amplitude. Not using transformers gives
better phase response that correlates best with detailed design simulations, but as a result of extra parasitic
capacitance at the device output pins gives significantly more peaking in the magnitude response. The –3dB
points of the magnitude response measured without transformers correlates better with measured slew rate, so
both magnitude and phase are plotted.
s-Parameters: s11, s22, and s12
The standard EVM is used with both R15 and R17 = 24.9Ω, and R16 = open, to test the input return loss, output
return loss, and reverse isolation. A network analyzer is connected to the input and output of the EVM with 50Ω
coaxial cables and set to measure the appropriate transfer function: s11, s22, or s12. Note the transformers are
included in the signal chain in order to retrieve proper measurements with single-ended test equipment. The
impact is minimal from 10MHz to 200MHz, but further analysis is required to fully de-embed the respective
effects.
Frequency Response with Capacitive Load
The standard EVM is used with R15 and R17 = RO, R16 = CLOAD, C9 and C13 = 953Ω, R21 = open, T2
removed, and jumpers placed across terminals 3 to 4 and 1 to 6. A network analyzer is connected to the input
and output of the EVM with 50Ω coaxial cables and set to measure the forward transfer function (s21). Different
values of load capacitance are placed on the output (at R16) and the output resistor values (R15 and R17)
changed until an optimally flat frequency response is achieved with maximum bandwidth.
Distortion
The standard EVM is used for measurement of single-tone harmonic distortion and two-tone intermodulation
distortion. For differential distortion measurements, the standard EVM is used with no modification. For
single-ended input distortion measurements, the standard EVM is used with with T1 removed and jumpers
placed across terminals 3 to 4 and 1 to 6, and R5 and R6 = 100Ω. A signal generator is connected to the J1
input of the EVM with 50Ω coaxial cables, with filters inserted inline to reduce distortion from the generator. The
J3 output of the EVM is connected with 50Ω coaxial cables to a spectrum analyzer to measure the
fundamental(s) and distortion products.
Noise Figure
The standard EVM is used with T1 changed to a 1:2 impedance ratio transformer (Mini-Circuits ADT2), R15 and
R17 = 24.9Ω, and R5, R6, and R16 = open. A noise figure analyzer is connected to the input and output of the
EVM with 50Ω coaxial cables. The noise figure analyzer provides a 50Ω (noise) source so that the data are
adjusted to refer to a 100Ω source.
16
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Transient Response, Slew Rate, Overdrive Recovery
The standard EVM is used with T1 and T2 removed and jumpers placed across terminals 3 to 4 and 1 to 6; R15,
R17, and R25 = 49.9Ω; C1, C2, C9, and C13 = 0Ω; and R5, R6, R16, and R21 = open. A differential waveform
generator is connected to the input of the EVM with 50Ω coaxial cables at J1 and J2. The differential output at J3
and J4 is connected with 50Ω coaxial cables to an oscilloscope to measure the outputs. Waveform math in the
oscilloscope is used to combine the differential output of the device.
Power-Down
The standard EVM is used with T1 and T2 removed, jumpers placed across terminals 3 to 4 and 1 to 6, R15 and
R17 = 49.9Ω, C9 and C13 = 0Ω, and R5, R6, R16, and R21 = open. A waveform generator is connected to the
power-down input of the EVM with a 50Ω coaxial cable at J8. The differential output at J3 and J4 is connected
with 50Ω coaxial cables to an oscilloscope to measure the outputs. J1 is left disconnected so that the output is
driven to the VOCM voltage when the device is active, and discharged through the resistive load on the output
when disabled. Both outputs are the same and only one is shown.
Differential Z-out
The standard EVM is used with R15 and R17 = 24.9Ω, and R16 = open. A network analyzer is connected to the
output of the EVM at J3 with 50Ω coaxial cable, both inputs are terminated with a 50Ω load, and a
high-impedance differential probe is used for the measurement. The analyzer is set to measure the forward
transfer function (s21). The analyzer with probe input is calibrated across the open resistor pads of R16 and the
signal is measured at the output pins of the device. The output impedance is calculated using the known resistor
values and the attenuation caused by R15 and R17.
Output Balance Error
The standard EVM is used with R15 and R17 = 100Ω, and R16 = 0Ω. A network analyzer is connected to the
input of the EVM with 50Ω coaxial cable, the output is left open, and a high-impedance differential probe is used
for the measurement. The analyzer is set to measure the forward transfer function (s21). The analyzer with probe
input is calibrated at the input pins of the device and the signal is measured from the shorted pads of R16 to
ground.
Common-Mode Rejection
The standard EVM is used with T1 removed and jumpers place across terminals 3 to 4, 1 to 6, and 1 to 3. A
network analyzer is connected to the input and output of the EVM with 50Ω coaxial cable and set to measure the
forward transfer function (s21).
VOCM Frequency Response
The standard EVM is used with T2 removed and jumpers across terminals 3 to 4 and 1 to 6; R10, R15, and
R17 = 49.9Ω; C3 and C4 = 0Ω; and R9, R16, and R21 = open. A network analyzer is connected to the VOCM
input of the EVM at J7 and output of the EVM with 50Ω coaxial cable, and set to measure the forward transfer
function (s21). The input signal frequency is swept with the signal level set for 200mV. Each output at J3 and J4
is measured as single-ended, and because both are the same, only one output is shown.
VOCM Slew Rate and Pulse Response
The standard EVM is used with T2 removed and jumpers across terminals 3 to 4 and 1 to 6; R10, R15, and
R17 = 49.9Ω; C9 and C13 = 0Ω; and C3, C4, R9, R16, and R21 = open. A waveform generator is connected to
the VOCM input of the EVM at J7 with 50Ω coaxial cable. The differential output at J3 and J4 is connected with
50Ω coaxial cable to an oscilloscope to measure the outputs. J1 is left disconnected so that the output is driven
to the VOCM voltage. Both outputs are the same, so only one is shown.
Input/Output Voltage Noise, Settling Time, and Power-Supply Rejection
These parameters are taken from simulation.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
THEORY OF OPERATION
GENERAL DESCRIPTION
The THS770006 is a fixed-gain of +6dB, wideband, fully-differential amplifier designed and optimized specifically
for driving 14-bit and 16-bit ADCs at input frequencies up to 200MHz. This device provides high bandwidth, low
distortion, and low noise, which are critical parameters in high-speed data acquisition systems that require very
high dynamic range, such as wireless base stations and test and measurement applications. It also makes an
excellent differential amplifier for general-purpose, high-speed differential signal chain and short line-driver
applications. The device has an operating power-supply range of 4.75V to 5.5V. The THS770006 has proprietary
circuitry to provide very fast recovery from overdrive conditions and has a power-down mode for power saving.
The THS770006 is offered in a Pb-free (RoHS compliant) and green, QFN-24 thermally-enhanced package. It is
characterized for operation over the industrial temperature range of –40°C to +85°C.
The amplifier uses two negative-feedback loops. One is for the primary differential amplifier and the other
controls the common-mode operation.
Primary Differential Amplifier
The primary amplifier of the THS770006 is a fully-differential op amp with on-chip gain setting resistors (RF =
100Ω and RG = 50Ω) that fix the differential gain at 2V/V, or 6dB, by use of negative feedback.
VOCM Control Loop
The output common-mode voltage is controlled through a second negative-feedback loop. The output
common-mode voltage is internally sensed and compared to the VOCM pin. The loop then works to drive the
difference, or error voltage, to zero in order to maintain the output common-mode voltage = VOCM (within the loop
gain and bandwidth of the loop). For more details on fully-differential amplifier theory and use, see application
report SLOA054, Fully-Differential Amplifiers, available for download from www.ti.com.
OPERATION
Differential to Differential
The THS770006 is a fixed gain of 6dB, fully-differential amplifier that can be used to amplify differential input
signals to differential output signals. A basic block diagram of the circuit is shown in Figure 33. The differential
input to differential output configuration gives the best performance; the signal source and load should be
balanced.
100W
Differential
Input
Differential
Output
50W
VIN-
VIN+
VOUT+
VOUT-
50W
100W
THS770006
Figure 33. Differential Input to Differential Output Amplifier
18
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Single-Ended to Differential
The THS770006 can be used to amplify and convert single-ended input signals to differential output signals. A
basic block diagram of the circuit is shown in Figure 34. The gain from the single-ended input to the differential
output is 6dB. In order to maintain proper balance in the amplifier and avoid offsets at the output, the alternate
input must be biased and the impedance matched to the signal input. For example, if a 50Ω source biased to
2.5V provides the input, the alternate input should be tied to 2.5V through 50Ω. If a 50Ω source is ac-coupled to
the input, the alternate input should be ac-coupled to ground through 50Ω. Note that the ac coupling should
provide a similar frequency response to balance the gain over frequency.
VREF
100W
Differential
Output
Bias and
Impedance
Match
50W
VOUT+
VOUT-
Single-Ended
Input
50W
100W
THS770006
Figure 34. Single-Ended Input to Differential Output Amplifier
Setting the Output Common-Mode Voltage
The VOCM input controls the output common-mode voltage. VOCM has no internal biasing network and must be
driven by an external source or resistor divider network to the positive power supply. In ac-coupled applications,
the VOCM input impedance and bias current are not critical, but in dc-coupled applications where more accuracy
is desired, the input bias current of the pin should be considered. For best harmonic distortion with VOUT = 3VPP
,
the VOCM input should be maintained within the operating range of 2.25V to 2.75V. The VOCM input voltage can
be operated outside this range if lower output swing is used or distortion degradation is allowed, and increased
bias current into the pin is acceptable. For more information, see Figure 12 and Figure 30. It is recommended to
use a 0.1µF decoupling capacitor from the VOCM pin to ground to prevent noise and other spurious signals from
coupling into the common-mode loop of the amplifier.
Input Common-Mode Voltage Range
The THS770006 is designed primarily for ac-coupled operation. With input dc blocking, the input common-mode
voltage of the device is driven to the same voltage as VOCM by the outputs. Therefore, as long as the VOCM input
is maintained within the operating range of 2.25V to 2.75V, the input common-mode of the main amplifier is also
maintained within its linear operating range of 2.25V to 2.75V. If the device is used with dc coupled input, the
driving source needs to bias the input to its linear operating range of 2.25V to 2.75V for proper operation.
Operation with Split Supply ±2.5V
The THS770006 can be operated using a split ±2.5V supply. In this case, VS+ is connected to +2.5V, and GND
(and any other pin noted to be connected to GND) is connected to -2.5V. As with any device, the THS770006 is
impervious to what the user decides to name the levels in the system. In essence, it is simply a level shift of the
power pins by –2.5V. If everything else is level-shifted by the same amount, the device sees no difference. With
a ±2.5V power supply, the VOCM range is 0V ±0.25V; therefore, power-down levels are –2.5V = on and +2.5V =
off, and input and output voltage ranges are symmetrical about 0V. This design has certain advantages in
systems where signals are referenced to ground, and as noted in the following section, for driving ADCs with low
input common-mode voltage requirements in dc-coupled applications.
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
Driving Capcitive Loads
The THS770006 is tested as described previously, with the data shown in the typical graphs. As a result of the
fixed gain architecture of the device, the only practical means to avoid stability problems such as
overshoot/ringing, gain peaking, and oscillation when driving capacitive loads is to place small resistors in series
with the outputs (RO) to isolate the phase shift caused by the capacitive load from the feedback loop of the
amplifier. The Typical Characteristics graphs show recommended values for an optimally flat frequency response
with maximum bandwidth. Smaller values of RO can be used if more peaking is allowed, and larger values can
be used to - reduce the bandwidth.
Driving ADCs
The THS770006 is designed and optimized for the highest performance to drive differential input ADCs.
Figure 35 shows a generic block diagram of the THS770006 driving an ADC. The primary interface circuit
between the amplifier and the ADC is usually a filter of some type for antialias purposes, and provides a means
to bias the signal to the input common-mode voltage required by the ADC. Filters range from single-order real
RC poles to higher-order LC filters, depending on the requirements of the application. Output resistors (RO) are
shown on the amplifier outputs to isolate the amplifier from any capacitive loading presented by the filter.
100W
RO
50W
VOUT+
AIN+
VIN-
VIN+
Filter
and
Bias
VOCM
ADC
CM
AIN-
VOUT-
RO
50W
100W
VOCM
THS770006
Figure 35. Generic ADC Driver Block Diagram
The key points to consider for implementation are described in the following three subsections.
SNR Considerations
The signal-to-noise ratio (SNR) of the amplifier + filter + ADC adds in RMS fashion. Noise from the amplifier is
bandwidth-limited by the filter. Depending on the amplitude of the signal and the bandwidth of the filter, the SNR
of the amplifier + filter can be calculated. To get the combined SNR, this value is then squared, added to the
square of the ADC SNR, and the square-root is taken. If the SNR of the amplifier + filter equals the SNR of the
ADC, the combined SNR is 3dB higher and for minimal inpact on the ADC's SNR the SNR of the amplifier + filter
should be 10dB or more lower. The combined SNR calculated in this manner is usually accurate to within ±1dB
of actual implementation.
SFDR Considerations
Theoretically, the spurious-free dynamic range (SFDR) of the amplifier + filter + ADC adds linearly on a
spur-by-spur basis. The amplifier output spurs are linearly related solely to the input signal and the SFDR is
usually set by second-order or third-order harmonic distortion for single-tone inputs, and by second-order or
third-order intermodulation distortion for two-tone inputs. Harmonic and second-order intermodulation distortion
can be filtered to some degree by the antialias filter, but not third-order intermodulation distortion. Generally, the
ADC also has the same distortion products, but as a result of the sampling nature and potential for clock
feedthrough, there may be spurs not linearly related solely to the input signal. When the spurs from the amplifier
+ filter are known, each can be directly added to the same spur from the ADC. This is a worst-case analysis
based on the assumption the spurs sources are in phase. If the spur of the amplifier + filter equals the spur of the
ADC, the combined spur is 6dB higher. The combined spur calculated in this manner is usually accurate to within
±6dB of actual implementation, but higher variations have been observed especially in second-order
performance as a result of phase shift in the filter.
20
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Common-mode phase shift introduced by the filter nullifies the basic assumption that the spur sources are in
phase. This phase shift can lead to better performance than predicted as the spurs become phase shifted, and
there is the potential for cancellation as the phase shift reaches 180°.
Differential phase shift in the filter as a result of mismatched components caused by nominal tolerance can
severely degrade the second-order distortion of the ADC. Single-order RC filters cause very little differential
phase shift with nominal tolerances of 5% or less, but higher-order LC filters are very sensitive to component
mismatch. For instance, a third-order Butterworth bandpass filter with 100MHz center frequency and 20MHz
bandwidth shows up to 20° differential phase imbalance in a Spice Monte Carlo analysis with 2% component
tolerances. Therefore, while a prototype may work, production variance is unacceptable. A transformer or balun
is recommended at the ADC input in these applications to restore the phase balance in the input signal to the
ADC.
ADC Input Common-Mode Voltage Considerations
The input common-mode voltage range of the ADC must be observed for proper operation. In an ac-coupled
application between the amplifier and the ADC, the input common-mode voltage bias of the ADC is
accomplished in different ways depending on the ADC. Some use internal bias networks and others use external
components, such as resistors, from each input to the CM output of the ADC. When ac coupling, the output
common-mode voltage of the amplifier is a don’t care for the ADC, and VOCM should be set for optimum
performance of the amplifier.
DC-coupled applications vary in complexity and requirements, depending on the ADC. Devices such as the
ADS5424 require a nominal 2.4V input common-mode, while others such as the ADS5485 require a nominal
3.1V input common-mode, and still others like the ADS6149 require 1.5V and the ADS4149 require 0.95V. Given
the THS770006 output common-mode range, ADCs with input common-mode closer to 2.5V are easier to
dc-couple to, and require little or no level shifting. For applications that require a different common-mode voltage
between the amplifier and the ADC, a resistor network can be used, as shown in Figure 36. With ADCs that have
internal resistors (RINT) that bias the ADC input to VCM, the bias resistors do not affect the desired value of RP,
but do cause more attenuation of the differential input signal. Knowing the differential input resistance is required
and sometimes, that is all that is provided.
VREF
RP
RO
RINT
VAMP+
VADC+
ADC
VCM
Amp
VAMP-
VADC-
RO
RINT
RP
VREF
Figure 36. Resistor Network to DC Level Shift Common-Mode Voltage
For common-mode analysis, assume that VAMP± = VOCM and VADC± = VADC (the specification for the ADC input
common-mode voltage). VREF is chosen to be a voltage within the system (such as the ADC or amplifier analog
supply) or ground, depending on whether the voltage must be pulled up or down, and RO is chosen to be a
reasonable value, such as 49.9Ω. With these known values, RP can be found by using Equation 1:
1
1
V
AMP - VADC
V
CM - VADC
=
+
V
ADC - VREF
RO
RINT
RP
(1)
The insertion of this resistor network also attenuates the amplifier output signal. The gain (or loss) can be
calculated by Equation 2:
RP || RINT
GAIN =
RO + (RP || RINT
)
(2)
21
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
Using the gain and knowing the full-scale input of the ADC, VADC FS, the required amplitude to drive the ADC with
the network can be calculated using Equation 3:
VAMP PP = VADC FS ´ GAIN
(3)
Using the ADC examples given previously, Table 2 shows sample calculations of the value of RP and VAMP FS for
full-scale drive, and then for –1dB (often times, the ADC drive is backed off from full-scale in applications, so
lower amplitudes may be acceptable). All voltages are in volts, resistors in Ω (the nearest standard value should
be used), and gain as noted. Table 2 does not include the ADS5424 because no level shift is required with this
device.
Table 2. Example RP for Various ADCs
VAMP PP
VOCM
VADC
VREF
GAIN
(V/V)
GAIN
(dB)
VADC FS
VAMP PP
–1dBFS
(VPP
ADC
(VDC
)
(VDC
)
(VDC
)
RINT (Ω)
1k
RO (Ω)
50
RP (Ω)
158.3
142.3
75.0
(VPP
)
FS (VPP
)
)
ADS5485
ADS5493
ADS6149
ADS4149
ADS4149
2.5
3.1
5
0.73
0.71
0.60
0.38
0.62
–2.71
–2.93
–4.44
–8.40
–4.15
2
4.10
3.65
3.12
2.97
4.69
2.88
2.5
3.15
1.5
5
1k
50
2.5
2
3.50
2.5
0
NA
50
3.33
2.5
0(1)
0.95
0.95
0
NA
50
30.6
2
5.26
2.5
NA
50
81.6
2
3.23
(1) THS770006 with ±2.5V supply.
The calculated values for the ADS5485 give the lowest attenuation, and because of the high VFS, it requires
3.65VPP from the amplifier to drive to –1dBFS. Performance of the THS770006 is still very good up to 130MHz at
this level, but the designer may want to further back off from full-scale for best performance and consider trading
reduced SNR performance for better SFDR performance.
The calculated values for the ADS5493 have lower attenuation as a result of reduced VFS, and requires 3.12VPP
from the amplifier to drive to –1dBFS. Performance of the THS770006 is excellent at this level up to 130MHz.
The values calculated for the ADS6149 show reasonable design targets and should work with good performance.
Note the ADS6149 does not have buffered inputs, and the inputs have equivalent resistive impedance that varies
with sampling frequency. In order to account for the increased loss, half of this resistance should be used for the
value of RINT in Equation 2.
The values calculated for the low input common-mode of the ADS4149 result in large attenuation of the amplifier
signal leading to 5.26VPP being required for full-scale ADC drive. This amplitude is greater than the maximum
capability of the device. With a single +5V supply, the THS770006 is not suitable to drive this ADC in dc-coupled
applications unless the ADC input is backed off towards –6dBFS. Another option is to operate the THS770006
with a split ±2.5V supply, and is shown in the last row of Table 2. For this situation, if the +2.5V is used as the
pull-up voltage, only 2.88VPP is required for the –1dBFS input to the ADS4149. See the Operation with Split
Supply ±2.5V section for more detail. Note that the ADS4149 does not have buffered inputs and the inputs have
equivalent resistive impedance that varies with sampling frequency. In order to account for the increased loss,
half of this resistance should be used for the value of RINT in Equation 2.
As with any design, testing is recommended to validate whether it meets the specific design goals.
22
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
APPLICATION INFORMATION
THS770006 DRIVING ADS5493
To illustrate the performance of the THS770006 as an ADC driver, the device is tested with the ADS5493. The
ADS5493 is a 16-bit, 130MSPS ADC with LVDS-compatible digital outputs on four data pairs. The device has an
analog input buffer to isolate the internal switching of the sampling stage from the inputs. Designed for high
SFDR, the ADC has low-noise performance and outstanding spurious-free dynamic range over a large
input-frequency range. Key information points to consider when interfacing to an amplifier are:
•
•
•
•
•
•
•
•
•
Input buffer with constant load vs frequency
3.15V analog input common mode
Full-scale differential input programmable from 1.5VPP to 2.5VPP
2kΩ differential input impedance with internal common-mode bias
4.6pF to 5.6pF for each analog input to ground (depending on PCB layout)
SNR = 75.2dBFS (typ) at fIN = 100MHz
SFDR = 100dBc (typ) at fIN = 100MHz
HD2 = 100dBc (typ) at fIN = 100MHz
HD3 = 100dBc (typ) at fIN = 100MHz
The ADS5493 EVM is designed for flexible options to ease design work. Used in conjunction with the
TSW1200EVM High Speed ADC LVDS Evaluation System, it reduces evaluation times to help the designer get
from prototype to production more quickly.
The ADS5493 EVM provides an input transformer for converting single-ended test signals to differential. The
differential outputs are configurable to drive the ADC directly through passive components or to insert the
THS770006 along with options for antialias filtering in the signal path to drive the ADC. The schematic of the
antialias filter components is shown in Figure 37. Note: the circuit shown is from an early prototype of the
ADS5493 EVM available at the time this data sheet was written and is provided as a reference only. The final
released board may have changes.
THS7700
Output
ADS5493
Input
Figure 37. ADS5493 EVM Antialias Filter Components
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
TESTING THE ADS5493 WITH AN AC-COUPLED BANDPASS FILTER
For testing purposes, a 30MHz, third-order Butterworth bandpass filter with center frequency at 100MHz is
designed and built on the EVM. The design target for the source impedance is 40Ω differential, and for load
impedance is 400Ω differential. Therefore, approximately 1dB insertion loss is expected in the pass-band,
requiring the amplifier output amplitude to be 2.5VPP to drive the ADC to –1dBFS.
The output noise voltage specification for the THS770006 is 3.4 nV/√Hz. With 2.5VPP amplifier output voltage
swing and 30MHz bandwidth, the expected SNR from the amplifier + antialias filter is 93.5dB. When added in
combination with the ADS5493, the expected total SNR is 75.1dBFS for the typical case.
Figure 38 shows the resulting FFT plot when driving the ADC to –1dBFS with a single-tone 100MHz sine wave,
and sampling at 125MSPS. Test results show 98dBc SFDR from the second-order harmonic and 75.6 dBFS
SNR; analysis of the plot is shown in Table 3 versus typical ADC specifications. The test results from circuit
board to circuit board shows over 10dB of variation in the second order harmonic and a balun is inserted
between the filter and ADC inputs to get repeatable performance. With balun, the minimum expected results
should be better than 90dBc SFDR and 75dBFS SNR.
Figure 38 shows the same circuit with a two-tone input at 96MHz and 100MHz. The near-in 3rd order
intermodulation terms are about -100dBc.
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
0
5
10 15 20 25 30 35 40 45 50 55
Frequency (MHz)
62.5
Figure 38. FFT Plot of THS770006 + 30MHz BPF + ADS5493 with Single-Tone at 100MHz
Table 3. Analysis of FFT for THS770006 + BPF + ADS5493 at 100MHz vs Typical ADC Specifications
CONFIGURATION
THS770006 + BPF + ADS5493
ADS5493 Only (typ)
ADC INPUT
–1dBFS
SNR
HD2
HD3
75.6dBFS
75.2dBFS
–98dBc
–100dBc
–107dBc
–100dBc
–1dBFS
10
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
130
140
0
5
10 15 20 25 30 35 40 45 50 55
Frequency (MHz)
61
Figure 39. FFT Plot of THS770006 + 30MHz BPF + ADS5493 with Two-Tone Input at 96MHz and 100MHz
24
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
TESTING THE ADS5493 WITH AN AC-COUPLED LOW-PASS FILTER
For testing the ADS5493, a 150MHz, first-order, low-pass filter is built on the EVM with the following component
changes: R10, R16, L3, and L24 = 100Ω, and C148 = 1.2pF. AC-coupling is done by inserting a 1µF capacitor
for C133 and C136. This design gives approximately 1.6dB insertion loss at low frequency, requiring the amplifier
signal be 2.7VPP in order to drive the ADC to -1dBFS.
With 2.7VPP amplifier output voltage swing and 180MHz (–3dB) bandwidth, the expected SNR from the amplifier
+ antialias filter is 84.4dB. When added in combination with the ADS5493, the total expected SNR is 74.7dBFS
for the typical case. Note the frequency response is approximately -1dB at 100MHz, which requires even higher
amplitude for the following test.
Figure 40 shows the resulting FFT plot when driving the ADC to –1dBFS with a 100MHz sine wave, and
sampling at 125MSPS. Test results showed 91dBc SFDR from second- and third-order harmonic and 73.1dBFS
SNR; analysis of the plot is shown in Table 4 versus typical ADC specifications. As a result of harmonic
attenuation and phase shift between the amplifier and ADC, harmonic performance is better than predicted from
the worst-case scenario described previously. Typical expected results should be approximately 90dBc SFDR
and 73dBFS SNR.
0
-10
-20
-30
-40
-50
-60
-70
-80
-90
-100
-110
-120
-130
0
5
10 15 20 25 30 35 40 45 50 55
Frequency (MHz)
62.5
Figure 40. FFT Plot of THS770006 + 180MHz LPF + ADS5493 with Single-Tone at 100MHz
Table 4. Analysis of FFT for THS770006 + 180MHz LPF + ADS5493 at 100MHz vs Typical ADC
Specifications
CONFIGURATION
THS770006 + BPF + ADS5493
ADS5493 Only (typ)
ADC INPUT
–1dBFS
SNR
HD2
HD3
73.1dBFS
75.2dBFS
–91dBc
–100dBc
–91dBc
–100dBc
–1dBFS
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
EVM AND LAYOUT RECOMMENDATIONS
Figure 32 is the THS770006RGE EVM schematic, and Figure 41 through Figure 44 show the layout details of the
EVM PCB. Table 5 is the bill of materials for the EVM as supplied from TI. It is recommended to follow the layout
of the external components as close as possible to the amplifier, ground plane construction, and power routing.
General layout guidelines are:
1. Place a 2.2µF to 10µF capacitor on each supply pin within 2 inches from the device. It can be shared among
other op amps.
2. Place a 0.01µF to 0.1µF capacitor on each supply pin to ground as close as possible to the device.
Placement within 1mm of the device supply pins ensures best performance.
3. Keep input and output traces as short as possible to minimize parasitic capacitance and inductance. Doing
so reduces unwanted characteristics such as reduced bandwidth and peaking in the frequency response,
overshoot, and ringing in the pulse response, and results in a more stable design.
4. To reduce parasitic capacitance, ground plane and power-supply planes should be removed from device
input pins and output pins.
5. The VOCM pin must be biased to a voltage between 2.25V to 2.75V for proper operation. Place a 0.1µF to
0.22µF capacitor to ground as close as possible to the device to prevent noise coupling into the
common-mode.
6. For best performance, drive circuits and loads should be balanced and biased to keep the input and output
common-mode voltage between 2.25V to 2.75V. AC-coupling is a simple way to achieve this performance.
7. The THS770006 is provided in a thermally enhanced PowerPAD™ package. The package is constructed
using a downset leadframe on which the die is mounted. This arrangement results in low thermal resistance
to the thermal pad on the underside of the package. Excellent thermal performance can be achieved by
following the guidelines in TI application reports SLMA002, PowerPAD™ Thermally-Enhanced Package and
SLMA004, PowerPAD™ Made Easy. For proper operation, the thermal pad on the bottom of the device must
be tied to the same voltage potential as the GND pin on the device.
Figure 41. EVM Layout: Top Layer
Figure 42. EVM Layout: Bottom Layer
26
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Figure 43. EVM Layout: Layer 2
Figure 44. EVM Layout: Layer 3
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s): THS770006
THS770006
SBOS520 –JULY 2010
www.ti.com
Table 5. THS770006RGE EVM Bill of Materials
SMD
SIZE
REFERENCE
DESIGNATOR
MANUFACTURER
PART NUMBER
DISTRIBUTOR
PART NUMBER
ITEM
DESCRIPTION
QTY
1
2
3
4
CAP, 10.0uF, CERAMIC, X7R, 10V
CAP, 0.1uF, CERAMIC, X7R, 16V
CAP, 0.01uF, CERAMIC, X7R, 16V
CAP, 100pF, CERAMIC, NPO, 50V
1206
0603
0402
0402
C4, C5, C6
C7, C8
3
2
2
1
(TDK) C3216X7R1A106K
(AVX) 0603YC104KAT2A
(AVX) 0402YC103KAT2A
(AVX) 04025A101KAT2A
(DIGI-KEY) 445-4043-1-ND
(DIGI-KEY) 478-1239-1-ND
(DIGI-KEY) 478-1114-1-ND
(DIGI-KEY) 478-4979-1-ND
C10, C11
C12
C1, C2, C3, C9,
C13
5
6
CAP, 1000pF, CERAMIC, X7R, 50V
OPEN
0402
0402
5
4
(AVX) 04025C102KAT2A
(DIGI-KEY) 478-1101-1-ND
R11, R12, R13,
R14
7
RESISTOR, 0 OHM
0402
0402
0402
0402
0402
0603
R4, R21
R5, R6
R16
2
2
1
2
2
2
2
(PANASONIC) ERJ-2GE0R00X
(PANASONIC) ERJ-2RKF49R9X
(PANASONIC) ERJ-2RKF57R6X
(PANASONIC) ERJ-2RKF1870X
(DIGI-KEY) P0.0JCT-ND
(DIGI-KEY) P49.9LCT-ND
(DIGI-KEY) P57.6LCT-ND
(DIGI-KEY) P187LCT-ND
8
RESISTOR, 49.9 OHM, 1/10W, 1%
RESISTOR, 57.6 OHM, 1/10W, 1%
RESISTOR, 187 OHM, 1/10W, 1%
RESISTOR, 1K OHM, 1/10W, 1%
RESISTOR, 10K OHM, 1/10W, 1%
TRANSFORMER, BALUN
9
10
11
12
13
R15, R17
R9, R10
R25, R26
T1, T2
(PANASONIC) ERJ-2RKF1001X (DIGI-KEY) P1.00KLCT-ND
(PANASONIC) ERJ-3EKF1002V (DIGI-KEY) P10.0KHCT-ND
(PULSE) CX2156NL
(SPC) 15459
(DIGI-KEY) 553-1499-ND
(NEWARK) 79K5034
JACK, BANANA RECEPTANCE, 0.25"
DIA. HOLE
14
J5, J6
3
15
16
17
18
19
20
21
22
23
24
CONNECTOR, SMA PCB JACK
CONNECTOR, EDGE, SMA PCB JACK
HEADER, 0.1" CTRS, 0.025" SQ. PINS
SHUNTS
J7, J8
J1, J2, J3, J4
JP1, JP2
JP1, JP2
TP3
2
4
2
2
1
2
1
4
4
(AMPHENOL) 901-144-8RFX
(JOHNSON) 142-0701-801
(SULLINS) PBC36SAAN
(SULLINS) SSC02SYAN
(KEYSTONE) 5000
(NEWARK) 34C8151
(NEWARK) 90F2624
3 POS.
(DIGI-KEY) S1011E-36-ND
(DIGI-KEY) S9002-ND
(DIGI-KEY) 5000K-ND
(DIGI-KEY) 5001K-ND
TEST POINT, RED
TEST POINT, BLACK
TP1, TP2
U1
(KEYSTONE) 5001
IC, THS770006
(TI) THS770006RGE
STANDOFF, 4-40 HEX, 0.625" LENGTH
SCREW, PHILLIPS, 4-40, .250"
BOARD, PRINTED CIRCUIT
(KEYSTONE) 1808
(DIGI-KEY) 1808K-ND
(DIGI-KEY) H703-ND
PMSSS 440 0025 PH
(TI) EDGE# 6515711 REV.A
28
Submit Documentation Feedback
Copyright © 2010, Texas Instruments Incorporated
Product Folder Link(s): THS770006
THS770006
www.ti.com
SBOS520 –JULY 2010
Evaluation Board/Kit Important Notice
Texas Instruments (TI) provides the enclosed product(s) under the following conditions:
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. Persons handling the product(s) must have
electronics training and observe good engineering practice standards. As such, the goods being provided are not intended to be complete
in terms of required design-, marketing-, and/or manufacturing-related protective considerations, including product safety and environmental
measures typically found in end products that incorporate such semiconductor components or circuit boards. This evaluation board/kit does
not fall within the scope of the European Union directives regarding electromagnetic compatibility, restricted substances (RoHS), recycling
(WEEE), FCC, CE or UL, and therefore may not meet the technical requirements of these directives or other related directives.
Should this evaluation board/kit not meet the specifications indicated in the User’s Guide, the board/kit may be returned within 30 days from
the date of delivery for a full refund. THE FOREGOING WARRANTY IS THE EXCLUSIVE WARRANTY MADE BY SELLER TO BUYER
AND IS IN LIEU OF ALL OTHER WARRANTIES, EXPRESSED, IMPLIED, OR STATUTORY, INCLUDING ANY WARRANTY OF
MERCHANTABILITY OR FITNESS FOR ANY PARTICULAR PURPOSE.
The user assumes all responsibility and liability for proper and safe handling of the goods. Further, the user indemnifies TI from all claims
arising from the handling or use of the goods. Due to the open construction of the product, it is the user’s responsibility to take any and all
appropriate precautions with regard to electrostatic discharge.
EXCEPT TO THE EXTENT OF THE INDEMNITY SET FORTH ABOVE, NEITHER PARTY SHALL BE LIABLE TO THE OTHER FOR ANY
INDIRECT, SPECIAL, INCIDENTAL, OR CONSEQUENTIAL DAMAGES.
TI currently deals with a variety of customers for products, and therefore our arrangement with the user is not exclusive.
TI assumes no liability for applications assistance, customer product design, software performance, or infringement of patents or
services described herein.
Please read the User’s Guide and, specifically, the Warnings and Restrictions notice in the User’s Guide prior to handling the product. This
notice contains important safety information about temperatures and voltages. For additional information on TI’s environmental and/or
safety programs, please contact the TI application engineer or visit www.ti.com/esh.
No license is granted under any patent right or other intellectual property right of TI covering or relating to any machine, process, or
combination in which such TI products or services might be or are used.
FCC Warning
This evaluation board/kit is intended for use for ENGINEERING DEVELOPMENT, DEMONSTRATION, OR EVALUATION PURPOSES
ONLY and is not considered by TI to be a finished end-product fit for general consumer use. It generates, uses, and can radiate radio
frequency energy and has not been tested for compliance with the limits of computing devices pursuant to part 15 of FCC rules, which are
designed to provide reasonable protection against radio frequency interference. Operation of this equipment in other environments may
cause interference with radio communications, in which case the user at his own expense will be required to take whatever measures may
be required to correct this interference.
EVM Warnings and Restrictions
It is important to operate this EVM within the input voltage range of 0V to +5.5V and the output voltage range of 0V to +5.5V.
Exceeding the specified input range may cause unexpected operation and/or irreversible damage to the EVM. If there are questions
concerning the input range, please contact a TI field representative prior to connecting the input power.
Applying loads outside of the specified output range may result in unintended operation and/or possible permanent damage to the EVM.
Please consult the EVM User's Guide prior to connecting any load to the EVM output. If there is uncertainty as to the load specification,
please contact a TI field representative.
During normal operation, some circuit components may have case temperatures greater than +85°C. The EVM is designed to operate
properly with certain components above +85°C as long as the input and output ranges are maintained. These components include but are
not limited to linear regulators, switching transistors, pass transistors, and current sense resistors. These types of devices can be identified
using the EVM schematic located in the EVM User's Guide. When placing measurement probes near these devices during operation,
please be aware that these devices may be very warm to the touch.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
Copyright © 2010, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Link(s): THS770006
PACKAGE OPTION ADDENDUM
www.ti.com
19-Aug-2010
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
THS770006IRGER
THS770006IRGET
ACTIVE
ACTIVE
VQFN
VQFN
RGE
RGE
24
24
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Request Free Samples
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Purchase Samples
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Aug-2010
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
THS770006IRGER
THS770006IRGET
VQFN
VQFN
RGE
RGE
24
24
3000
250
330.0
180.0
12.4
12.4
4.25
4.25
4.25
4.25
1.15
1.15
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
27-Aug-2010
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
THS770006IRGER
THS770006IRGET
VQFN
VQFN
RGE
RGE
24
24
3000
250
346.0
190.5
346.0
212.7
29.0
31.8
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
Automotive
www.ti.com/automotive
www.ti.com/communications
Communications and
Telecom
DSP
dsp.ti.com
Computers and
Peripherals
www.ti.com/computers
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Consumer Electronics
Energy
www.ti.com/consumer-apps
www.ti.com/energy
Logic
Industrial
www.ti.com/industrial
Power Mgmt
Microcontrollers
RFID
power.ti.com
Medical
www.ti.com/medical
microcontroller.ti.com
www.ti-rfid.com
Security
www.ti.com/security
Space, Avionics &
Defense
www.ti.com/space-avionics-defense
RF/IF and ZigBee® Solutions www.ti.com/lprf
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2010, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明