TLE2662IDW [TI]
DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER; 双微功耗JFET输入运算放大器,开关电容电压转换器型号: | TLE2662IDW |
厂家: | TEXAS INSTRUMENTS |
描述: | DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER |
文件: | 总40页 (文件大小:588K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
DW PACKAGE
(TOP VIEW)
Single-Supply Operation With Rail-to-Rail
Inputs
= 0.000 V While Sinking 25 mA
V
OL
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
CC+
2OUT
Wide V
Range . . . 3.5 V to 15 V
CC
SCOUT Supplies up to 100 mA for External
Loads
2IN–
2IN+
CAP–
GND
CAP+
FB/SD
V
CC–
Shutdown Mode
SCOUT
SCREF
OSC
External 2.5-V Voltage Reference Available
description
SCIN
TheTLE2662offerstheadvantagesofJFET-input
operational amplifiers and rail-to-rail common-
mode input voltage range with the convenience of single-supply operation. By combining a switched-capacitor
voltage converter with a dual operational amplifier in a single package, Texas Instruments now gives circuit
designers new options for conditioning low-level signals in single-supply systems.
The TLE2662 features two low power, high-output drive JFET-input operational amplifiers with a switched-
capacitor building block. Using two external capacitors, the switched-capacitor network can be configured as
a voltage inverter, generating a negative supply voltage capable of sourcing up to 100 mA. This supply functions
not only as the amplifier negative rail but is also available to drive external circuitry. In this configuration, the
amplifier common-mode input voltage range extends from the positive rail to below ground, providing true
rail-to-rail inputs from a single supply. Furthermore, the outputs can swing to and below ground while sinking
over 25 mA. This feature was previously unavailable in operational amplifier circuits. The TLE2662 operational
amplifier section has output stages that can drive 100-Ω loads to 2.5 V from a 5-V rail. With a 10-kΩ load, the
output swing extends to 3.5 V and can include the positive rail with a pullup resistor.
This operational amplifier offers the high slew rate, wide bandwidth, and high input impedance commonly
associated with JFET-input amplifiers, making the TLE2662 operational amplifier section suited for amplifying
fast signals without loading the signal source. When not sourcing or sinking current into a load, the amplifier
consumes only microamperes of supply current, thereby reducing the drain on and extending the life of the
power supply.
The TLE2662 features a shutdown pin (FB/SD), which can be used to disable the switched capacitor section.
When disabled, the voltage converter block draws less than 150 µA from the power supply. This feature,
combined with the operational amplifier’s low quiescent current, makes the TLE2662 a real power saver in the
standby mode.
The switched-capacitor building block also provides an on-board regulator; with the addition of an external
divider, awell-regulatedoutputvoltageiseasilyobtained. Additionalfilteringcanbeaddedtominimizeswitching
noise. The internal oscillator runs at a nominal frequency of 25 kHz. This can be synchronized to an external
clock signal or can be varied using an external capacitor. A 2.5-V reference is brought out to SCREF for use
with the on-board regulator or external circuitry.
TheTLE2662ischaracterizedforoperationovertheindustrialtemperaturerangeof –40°Cto85°C. Thisdevice
is available in a 16-pin wide-body surface-mount package.
AVAILABLE OPTION
PACKAGE
T
A
SMALL OUTLINE
(DW)
–40°C to 85°C
TLE2662IDW
The DW package is available taped and reeled. Add
the suffix R to the device type (i.e., TLE2662IDWR).
Copyright 1994, Texas Instruments Incorporated
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of Texas Instruments
standard warranty. Production processing does not necessarily include
testing of all parameters.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
functional block diagram
Amplifier Block
1
16
15
14
13
12
11
10
9
1OUT
V
CC+
2
_
+
1IN–
1IN+
2OUT
2IN–
_
+
3
4
5
6
7
8
V
CC–
2IN+
SCOUT
CAP–
GND
SCREF
OSC
Switched-
Capacitor
Block
CAP+
FB/SD
SCIN
ACTUAL DEVICE COMPONENT COUNT
AMPLIFIER
BLOCK
SWITCHED-
CAPACITOR BLOCK
Transistors
42
9
Transistors
Resistors
Diodes
71
44
2
Resistors
Diodes
3
Capacitors
2
Capacitors
5
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Supply voltage, SCIN (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V
Supply voltage, V
Supply voltage, V
(see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 16 V
(see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –16 V
CC+
CC–
Differential input voltage, V (see Note 3) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 32 V
ID
Input voltage, V (any input of amplifier) (see Note 2) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . V
I
CC±
FB/SD (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to SCIN
OSC (see Note 1) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to SCREF
Input current, I (each input of amplifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ±1 mA
I
Output current, I (each output of amplifier) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 80 mA
O
Total current into V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 80 mA
CC+
CC–
Total current out of V
Duration of short-circuit current at (or below) T = 25°C (see Note 4) . . . . . . . . . . . . . . . . . . . . . . . . . unlimited
Continuous total dissipation . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . See Dissipation Rating Table
A
Junction temperature (see Note 5) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 150°C
Operating free-air temperature range, T
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –40°C to 85°C
A
Storage temperature range . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65°C to 150°C
Lead temperature 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 260°C
†
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
NOTES: 1. Voltage values are with respect to the switched-capacitor block GND.
2. Voltage values, except differential voltages, are with respect to the midpoint between V
3. Differential voltages are at IN+ with respect to IN–.
and V
.
CC–
CC+
4. The output can be shorted to either supply. Temperature and/or supply voltages must be limited to ensure that the maximum
dissipation rating is not exceeded.
5. The devices are functional up to the absolute maximum junction temperature.
DISSIPATION RATING TABLE
T
≤ 25°C
DERATING FACTOR
T
= 70°C
T = 85°C
A
POWER RATING
A
A
PACKAGE
POWER RATING
ABOVE T = 25°C
POWER RATING
A
DW
1025 mW
8.2 mW/°C
656 mW
533 mW
recommended operating conditions
MIN
3.5
MAX
15
UNIT
Supply voltage, V
/SCIN
V
CC+
V
V
= ±5 V
–1.6
–11
–40
0
4
CC±
Common-mode input voltage, V
V
IC
Operating free-air temperature, T
= ±15 V
13
CC±
85
°C
A
Output current at SCOUT, I
100
mA
O
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
OPERATIONAL AMPLIFIER SECTION
electrical characteristics at specified free-air temperature, V
= ±5 V (unless otherwise noted)
CC±
†
‡
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
5
UNIT
25°C
Full range
Full range
25°C
1
V
IO
Input offset voltage
mV
6.3
α
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 6)
6
0.04
1
µV/°C
µV/mo
pA
VIO
V
IC
= 0,
R
= 50 Ω
S
25°C
I
I
Input offset current
Input bias current
IO
Full range
25°C
2
4
nA
3
pA
IB
Full range
nA
–1.6
to
–2
to
6
25°C
V
V
4
V
ICR
Common-mode input voltage range
–1.6
to
Full range
4
25°C
Full range
25°C
3.4
3
3.7
3.1
–3.9
–2.7
80
I
I
I
I
= 2 mA
= 20 mA
= 2 mA
= 20 mA
L
L
L
L
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
V
V
OM+
2.5
2
Full range
25°C
–3.4
–3
Full range
25°C
OM–
–2.5
–2
Full range
25°C
15
V
V
V
= ± 2.8 V,
R
R
R
= 10 kΩ
= 100 Ω
= 100 Ω
O
O
O
L
L
L
Full range
25°C
2
0.75
0.5
0.5
0.25
45
A
VD
Large-signal differential voltage amplification
= 0 to 2 V,
= 0 to –2 V,
V/mV
Full range
25°C
3
Full range
25°C
12
4
r
i
Input resistance
10
Ω
pF
Ω
C
Input capacitance
25°C
i
z
Open-loop output impedance
I
O
= 0
25°C
560
82
o
25°C
65
65
75
65
R
V
= 50 Ω,
S
CMRR Common-mode rejection ratio
dB
dB
µA
= V
min
Full range
25°C
IC
ICR
93
V
R
= ± 5 V to ±15 V,
= 50 Ω
CC±
S
k
Supply-voltage rejection ratio (∆V
/∆V
)
IO
SVR
CC±
Full range
25°C
560
620
640
I
Supply current
I = 0
L
CC
Full range
supply.
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
CC–
‡
Full range is –40°C to 85°C.
NOTE 6: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, V
= ±5 V
CC±
†
‡
PARAMETER
TEST CONDITIONS
T
A
MIN
2.2
TYP
MAX
UNIT
25°C
Full range
25°C
3.4
SR
Slew rate at unity gain (see Figure 1)
R
= 10 kΩ,
C
= 100 pF
V/µs
L
L
1.7
f = 10 Hz,
f = 1 kHz,
R
R
= 20 Ω
= 20 Ω
59
43
1.1
1
100
60
S
S
V
n
Equivalent input noise voltage (see Figure 2)
nV/√Hz
25°C
V
Peak-to-peak equivalent input noise voltage
Equivalent input noise current
f = 0.1 Hz to 10 Hz
f = 1 kHz
25°C
µV
N(PP)
I
n
25°C
fA/√Hz
V
A
= 2 V,
f = 10 kHz,
O(PP)
= 2,
THD
Total harmonic distortion
25°C
0.025%
R
C
C
= 10 kΩ
= 100 pF
= 100 pF
VD
L
L
L
R
= 10 kΩ,
25°C
25°C
1.8
1.3
5
L
L
B
1
Unity-gain bandwidth (see Figure 3)
MHz
R
= 100 Ω,
To 0.1%
To 0.01%
25°C
t
s
Settling time
µs
25°C
10
B
Maximum output-swing bandwidth
Phase margin at unity gain (see Figure 3)
A
= 1,
R
C
C
= 10 kΩ
= 100 pF
= 100 pF
25°C
140
58°
75°
kHz
OM
VD
L
L
L
R
R
= 10 kΩ,
= 100 Ω,
25°C
L
L
φ
m
25°C
†
‡
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
Full range is –40°C to 85°C.
supply.
CC–
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
electrical characteristics at specified free-air temperature, V
= ±15 V (unless otherwise noted)
CC±
†
‡
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
4
UNIT
25°C
Full range
Full range
25°C
0.9
V
IO
Input offset voltage
mV
5.3
α
Temperature coefficient of input offset voltage
Input offset voltage long-term drift (see Note 6)
6
0.04
2
µV/°C
µV/mo
pA
VIO
V
IC
= 0,
R
= 50 Ω
S
25°C
I
I
Input offset current
Input bias current
IO
Full range
25°C
3
5
nA
4
pA
IB
Full range
nA
–11
to
13
–12
to
16
25°C
V
V
V
ICR
Common-mode input voltage range
–11
to
Full range
13
25°C
Full range
25°C
13.2
13
13.7
13.2
I
I
I
I
= 2 mA
= 20 mA
= 2 mA
= 20 mA
L
L
L
L
V
V
Maximum positive peak output voltage swing
Maximum negative peak output voltage swing
V
V
OM+
12.5
12
Full range
25°C
–13.2 –13.7
–13
Full range
25°C
OM–
–12.5
–12
30
–13
230
100
25
Full range
25°C
V
V
V
= ± 10 V,
R
R
R
= 10 kΩ
= 600 Ω
= 600 Ω
O
O
O
L
L
L
Full range
25°C
20
25
A
VD
Large-signal differential voltage amplification
= 0 to 8 V,
= 0 to –8 V,
V/mV
Full range
25°C
10
3
Full range
25°C
1
12
4
r
i
Input resistance
10
Ω
pF
Ω
C
Input capacitance
25°C
i
z
Open-loop output impedance
I
O
= 0
25°C
560
90
o
25°C
72
65
75
65
R
V
= 50 Ω,
S
CMRR Common-mode rejection ratio
dB
dB
µA
= V
min
Full range
25°C
IC
ICR
93
V
R
= ± 5 V to ±15 V,
= 50 Ω
CC±
S
k
Supply-voltage rejection ratio (∆V
/∆V
)
IO
SVR
CC±
Full range
25°C
625
690
720
I
Supply current
I = 0
L
CC
Full range
supply.
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
CC–
‡
Full range is –40°C to 85°C.
NOTE 6: Typical values are based on the input offset voltage shift observed through 168 hours of operating life test at T = 150°C extrapolated
A
to T = 25°C using the Arrhenius equation and assuming an activation energy of 0.96 eV.
A
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
operating characteristics at specified free-air temperature, V
= ±15 V
CC±
†
‡
PARAMETER
TEST CONDITIONS
T
A
MIN
2.6
TYP
MAX
UNIT
25°C
3.4
SR
Slew rate at unity gain (see Figure 1)
R
= 10 kΩ,
C
= 100 pF
V/µs
L
L
Full range
25°C
2.1
f = 10 Hz,
f = 1 kHz,
R
R
= 20 Ω
= 20 Ω
70
40
100
60
Equivalent input noise voltage
(see Figure 2)
S
S
V
n
nV/√Hz
25°C
Peak-to-peak equivalent input noise
voltage
V
f = 0.1 Hz to 10 Hz
f = 1 kHz
25°C
25°C
25°C
1.1
1.1
µV
N(PP)
I
n
Equivalent input noise current
Total harmonic distortion
fA/√Hz
V
A
= 2 V,
f = 10 kHz,
O(PP)
= 2,
THD
0.025%
R
C
C
= 10 kΩ
= 100 pF
= 100 pF
VD
L
L
L
R
= 10 kΩ,
25°C
25°C
25°C
25°C
25°C
25°C
25°C
2
1.5
5
L
L
B
1
Unity-gain bandwidth (see Figure 3)
MHz
R
= 600 Ω,
To 0.1%
To 0.01%
t
s
Settling time
µs
10
B
OM
Maximum output-swing bandwidth
Phase margin at unity gain (see Figure 3)
A
= 1,
R
C
C
= 10 kΩ
= 100 pF
= 100 pF
40
kHz
VD
L
L
L
R
R
= 10 kΩ,
= 600 Ω,
60°
70°
L
L
φ
m
†
‡
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
Full range is –40°C to 85°C.
supply.
CC–
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
SWITCHED-CAPACITOR SECTION
electrical characteristics over recommended supply voltage range and at specified free-air
temperature
†
‡
PARAMETER
TEST CONDITIONS
T
A
MIN
TYP
MAX
UNIT
SCIN = 7 V,
See Note 7
–5.2
–5
–4.7
Regulated output voltage,
SCOUT
R
R
R
= 500 Ω
25°C
V
L(SCOUT)
L(SCOUT)
L(SCOUT)
SCIN = 5 V,
See Note 8
–4.25
–4 –3.75
SCIN = 7 V to 12 V,
See Note 7
5
25
27
Input regulation
= 500 Ω
Full range
Full range
mV
SCIN = 5 V to 15 V,
See Note 8
SCIN = 7 V,
See Note 7
10
50
Output regulation
= 100 Ω to 500 Ω
mV
V
SCIN = 5 V,
See Note 8
100
I
I
= 10 mA
0.35
1.1
0.55
1.6
Voltage loss, SCIN – SCOUT
(see Note 9)
SCIN = 7 V,
CIN = COUT = 100-µF tantalum
O
Full range
Full range
= 100 mA
O
SCIN = 7 V,
See Note 10
∆I = 10 mA to 100 mA,
O
Output resistance
10
15
Ω
Oscillator frequency
Full range
25°C
15
2.35
2.25
2.35
2.25
25
35
2.65
2.75
2.65
2.75
kHz
2.5
SCIN = 7 V,
SCIN = 5 V,
I
I
= 60 µA
= 50 µA
V
ref
Full range
25°C
Reference voltage, V
ref
2.5
V
ref
Full range
25°C
Maximum switch current
Supply current, I
300
2.5
3
mA
mA
µA
SCIN = 3.5 V
SCIN = 15 V
SCIN = 5 V
3.5
4.5
I
O
= 0
Full range
Full range
S
Supply current in shutdown
V
= 0,
I
O
= 0,
100
150
(FB/SD)
†
‡
Data applies for the switched-capacitor block only. Amplifier block is not connected.
Full range is –40°C to 85°C.
NOTES: 7. All regulation specifications are for the switched-capacitor section connected as a positive to negative converter/regulator with
R1 = 20 kΩ, R2 = 102.5 kΩ, CIN = 10 µF (tantalum), COUT = 100 µF (tantalum) and C1 = 0.002 µF (see Figure 63).
8. All regulation specifications are for the switched-capacitor section connected as a positive to negative converter/regulator with
R1 = 23.7 kΩ, R2 = 102.2 kΩ, CIN = 10 µF (tantalum), COUT = 100 µF (tantalum) and C1 = 0.002 µF (see Figure 63).
9. For voltage-loss tests, the switched-capacitor section is connected as a voltage inverter, with SCREF, OSC, and FB/SD
unconnected. The voltage losses may be higher in other configurations.
10. Outputresistance is defined as the slope of the curve (∆V vs ∆I )foroutputcurrentsof10mAto100mA. Thisrepresentsthelinear
O
O
portion of the curve. The incremental slope of the curve is higher at currents less than 10 mA due to the characteristics of the switch
transistors.
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
AMPLIFIER AND SWITCHED-CAPACITOR SECTIONS CONNECTED
electrical characteristics, V
= 5 V, T = 25°C (see Figure 4)
CC+
A
PARAMETER
TEST CONDITIONS
MIN
TYP
3.7
MAX
UNIT
R
R
R
R
R
R
= 10 kΩ
= 600 Ω
= 100 Ω
= 10 kΩ
= 600 Ω
= 100 Ω
L
L
L
L
L
L
Maximum positive peak output voltage swing, V
OM+
3.5
V
3.1
–3.7
–3.0
–2.2
0.46
0.50
0.9
Maximum negative peak output voltage swing, V
Voltage loss, SCIN – |SCOUT| (see Note 9)
V
V
OM–
R
R
R
= 10 kΩ
= 600 Ω
= 100 Ω
L
L
L
CIN = COUT = 100-µF tantalum,
= –100 mV,
V
ID
Both amplifiers
NOTES: 9. For voltage-loss tests, the switched-capacitor section is connected as a voltage inverter with SCREF, OSC, and FB/SD
unconnected. The voltage losses may be higher in other configurations.
supply current (no load), T = 25°C
A
PARAMETER
TEST CONDITIONS
MIN
TYP
3.4
MAX
UNIT
mA
Supply current
V
V
= 5 V,
= 5 V,
SCIN = 5 V,
SCIN = 5 V,
V
= 2.5 V,
= 0 V,
V
V
= 0
= 0
CC+
(FB/SD)
(FB/SD)
O
Supply current in shutdown
V
265
µA
CC+
O
PARAMETER MEASUREMENT INFORMATION
operational amplifier
2 kΩ
V
CC+
V
CC+
–
V
O
–
+
V
O
V
I
+
V
CC–
C
R
L
L
V
CC–
R = 20 Ω
S
(see Note A)
R
= 20 Ω
S
NOTE A: C includes fixture capacitance.
L
Figure 1. Slew-Rate Test Circuit
Figure 2. Noise-Voltage Test Circuit
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
PARAMETER MEASUREMENT INFORMATION
10 kΩ
V
CC+
100 Ω
V
I
–
+
V
O
V
CC–
C
R
L
L
(see Note A)
NOTE A: C includes fixture capacitance.
L
Figure 3. Unity-Gain Bandwidth and Phase-Margin Test Circuit
amplifier input bias offset current
At the picoampere bias-current level typical of the TLE2662, accurate measurement of the amplifier’s bias
current becomes difficult. Not only does this measurement require a picoammeter, but test socket leakages can
easily exceed the actual device bias currents. To accurately measure these small currents, Texas Instruments
uses a two-step process. The socket leakage is measured using picoammeters with bias voltages applied but
with no device in the socket. The device is then inserted into the socket and a second test that measures both
the socket leakage and the device input bias current is performed. The two measurements are then subtracted
algebraically to determine the bias current of the device.
R
L
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
+
CC
+
0.1 µF
2 µF
2OUT
2IN–
R
L
V
CC–
2IN+
TLE2662
SCOUT
SCREF
OSC
CAP–
GND
COUT
0.1 µF
+
CIN
1N4933
+
CAP+
FB/SD
SCIN
Figure 4. Test Circuit
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
TYPICAL CHARACTERISTICS
Table of Graphs
operational amplifier section
FIGURE
V
Input offset voltage
Distribution
5
6
6
7
IO
I
Input bias current
vs Free-air temperature
vs Free-air temperature
vs Free-air temperature
IB
IO
I
Input offset current
V
V
V
Common-mode input voltage
IC
vs Output current
vs Supply voltage
8, 9
10,11,12
Maximum peak output voltage
OM
Maximum peak-to-peak output voltage
Differential voltage amplification
vs Frequency
13, 14
O(PP)
vs Frequency
vs Free-air temperature
15
16
A
VD
OS
vs Time
vs Free-air temperature
17
18
I
Short-circuit output current
Output impedance
z
vs Frequency
vs Frequency
19
20
o
CMRR Common-mode rejection ratio
vs Supply voltage
vs Free-air temperature
21
22
I
Supply current
Pulse response
CC
Small signal
Large signal
23, 24
25, 26
Noise voltage (referenced to input)
Equivalent input noise voltage
Total harmonic distortion
0.1 to 10 Hz
vs Frequency
vs Frequency
27
28
V
n
THD
29, 30
vs Supply voltage
vs Free-air temperature
31
32
B
1
Unity-gain bandwidth
vs Supply voltage
vs Load capacitance
vs Free-air temperature
33
34
35
φ
m
Phase margin
Phase shift
vs Frequency
15
switched-capacitor section
Shutdown threshold voltage
vs Free-air temperature
vs Input voltage
36
37
38
39
40
I
f
Supply current
CC
Oscillator frequency
Supply current in shutdown
Average supply current
vs Free-air temperature
vs Input voltage
osc
vs Output current
vs Input capacitance
vs Oscillator frequency
41
42, 43
Output voltage loss
V
O
Regulated output voltage
Reference voltage change
Voltage loss
vs Free-air temperature
vs Free-air temperature
vs Output current
44
45
46
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
INPUT BIAS CURRENT
AND INPUT OFFSET CURRENT
vs
DISTRIBUTION OF
INPUT OFFSET VOLTAGE
FREE-AIR TEMPERATURE
15
5
10
V
V
= ±15 V
= 0
IC
1836 Amplifiers Tested From 1 Wafer Lot
CC±
V = ±15 V
CC±
= 25°C
T
A
4
3
2
10
10
10
10
I
IB
5
I
IO
1
0
10
0
10
– 4 – 3 – 2
– 1
0
1
2
3
4
25
45
65
85
V
IO
– Input Offset Voltage – mV
T
A
– Free-Air Temperature – °C
Figure 5
Figure 6
COMMON-MODE INPUT VOLTAGE
vs
MAXIMUM POSITIVE PEAK OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
OUTPUT CURRENT
20
V
V
+2
+1
CC+
T
A
= 25°C
18
16
14
CC+
V
IC+
V
CC±
= ±15 V
12
V
CC+
10
8
V
V
V
+4
+3
+2
CC–
6
4
2
0
CC–
CC–
V
IC–
V
CC±
= ±5 V
0
–10
– 20
I – Output Current – mA
O
– 30
– 40
– 50
– 60
– 75 – 50 – 25
0
25
50
75
100
T
A
– Free-Air Temperature – °C
Figure 7
Figure 8
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
12
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
MAXIMUM NEGATIVE PEAK OUTPUT VOLTAGE
MAXIMUM PEAK OUTPUT VOLTAGE
vs
vs
OUTPUT CURRENT
SUPPLY VOLTAGE
20
15
– 20
– 18
– 16
– 14
R
= 10 kΩ
= 25°C
L
T
A
= 25°C
T
A
10
V
OM+
5
V
CC±
= ±15 V
– 12
– 10
0
– 8
– 5
– 10
– 6
– 4
– 2
0
V
OM–
V
= ±5 V
– 15
– 20
CC±
0
5
10
15
20
25
30
35
40
0
2
4
6
8
10
12
14
16
I
O
– Output Current – mA
|V | – Supply Voltage – V
CC±
Figure 9
Figure 10
MAXIMUM PEAK OUTPUT VOLTAGE
MAXIMUM PEAK OUTPUT VOLTAGE
vs
vs
SUPPLY VOLTAGE
SUPPLY VOLTAGE
20
15
6
4
R
= 100 Ω
= 25°C
R
T
= 600 Ω
L
L
T
A
= 25°C
A
V
OM+
10
V
OM+
2
5
0
0
– 5
– 10
– 2
– 4
– 6
V
OM–
V
OM–
– 15
– 20
0
2
4
6
8
10
12
14
16
0
2
4
6
8
|V | – Supply Voltage – V
CC±
|V | – Supply Voltage – V
CC±
Figure 11
Figure 12
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
13
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
MAXIMUM PEAK-TO-PEAK OUTPUT VOLTAGE
vs
vs
FREQUENCY
FREQUENCY
30
25
10
8
V
R
= ±5 V
CC±
= 10 kΩ
V
R
= ±15 V
CC±
= 10 kΩ
L
L
T
A
= 25°C
T
A
= 25°C
20
15
10
6
4
2
5
0
0
10 k
100 k
1 M
10 M
10 k
100 k
1 M
10 M
f – Frequency – Hz
f – Frequency – Hz
Figure 13
Figure 14
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION and PHASE SHIFT
vs
FREQUENCY
120
60°
Phase Shift
100
80
80°
100°
120°
A
VD
60
40
140°
20
0
160°
180°
200°
V
= ±15 V
CC±
R
= 10 kΩ
L
L
C
= 100 pF
T
A
= 25°C
– 20
0.1
1
10
100 1 k 10 k 100 k 1 M 10 M
f – Frequency – Hz
Figure 15
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
14
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
LARGE-SIGNAL DIFFERENTIAL VOLTAGE
AMPLIFICATION
vs
FREE-AIR TEMPERATURE
400
350
300
R
= 10 kΩ
L
250
V
CC±
= ±15 V
200
150
V
CC±
= ±5 V
100
50
0
– 75 – 50 – 25
0
25
50
75
100
T
A
– Free-Air Temperature – °C
Figure 16
SHORT-CIRCUIT OUTPUT CURRENT
SHORT-CIRCUIT OUTPUT CURRENT
vs
vs
TIME
FREE-AIR TEMPERATURE
80
60
40
20
80
60
40
20
V
V
= ±15 V
CC±
V
ID
= –100 mV
= 0
O
V
ID
= –100 mV
V
T
= ±15 V
CC±
= 25°C
A
V
O
= 0
0
0
– 20
– 20
V
ID
= 100 mV
– 40
– 60
– 80
– 40
– 60
– 80
V
= 100 mV
50
ID
0
10
20
30
40
60
– 75 – 50 – 25
0
25
50
75
100
t – Time – s
T
A
– Free-Air Temperature – °C
Figure 17
Figure 18
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
15
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
COMMON-MODE REJECTION RATIO
OUTPUT IMPEDANCE
vs
vs
FREQUENCY
FREQUENCY
35
30
25
20
100
80
V
= ±15 V
T
A
= 25°C
CC±
= 25°C
T
A
V
CC±
= ±5 V
A
= 10
VD
60
15
10
40
A
VD
= 100
A
VD
= 1
20
0
5
0
100
1 k
10 k
100 k
1 M
10 M
10 M
10
100
1 k
10 k
100 k
1 M
f – Frequency – Hz
f – Frequency – Hz
Figure 19
Figure 20
SUPPLY CURRENT
vs
SUPPLY CURRENT
vs
SUPPLY VOLTAGE
FREE-AIR TEMPERATURE
700
675
650
625
600
575
550
700
675
650
625
600
575
550
V
= 0
O
No Load
V
= 0
O
No Load
T
A
= 85°C
V
CC±
= ±15 V
T
= 25°C
A
V
CC±
= ±5 V
T
A
= –55°C
525
500
525
500
0
2
4
6
8
10
12
14
16
– 75 – 50 – 25
0
25
50
75
100
|V | – Supply Voltage – V
CC±
T
A
– Free-Air Temperature – °C
Figure 21
Figure 22
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
16
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
VOLTAGE-FOLLOWER SMALL-SIGNAL
PULSE RESPONSE
100
50
100
50
0
0
V
R
C
= ±5 V
= 10 kΩ
= 100 pF
= 25°C
CC±
L
L
V
R
C
= ±15 V
= 10 kΩ
= 100 pF
= 25°C
CC±
L
L
– 50
– 50
T
A
T
A
See Figure 1
See Figure 1
– 100
– 100
0
1
2
3
0
1
2
3
t – Time – µs
t – Time – µs
Figure 23
Figure 24
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
VOLTAGE-FOLLOWER LARGE-SIGNAL
PULSE RESPONSE
4
3
2
1
0
15
V
= ±5 V
V
R
= ±15 V
= 10 kΩ
= 100 pF
= 25°C
CC±
L
L
CC ±
L
L
R
C
T
= 10 kΩ
= 100 pF
= 25°C
C
T
10
5
A
A
See Figure 1
See Figure 1
0
– 5
– 10
– 15
– 1
– 2
0
5
10
15
0
10
20
30
40
t – Time – µs
t – Time – µs
Figure 25
Figure 26
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
17
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
NOISE VOLTAGE
(REFERRED TO INPUT)
0.1 TO 10 Hz
EQUIVALENT INPUT NOISE VOLTAGE
vs
FREQUENCY
1
100
80
V
T
= ±15 V
CC±
= 25°C
V
R
= ±5 V
DD±
= 20Ω
A
S
T
= 25°C
A
See Figure 2
0.5
60
0
– 0.5
– 1
40
20
0
0
1
2
3
4
5
6
7
8
9
10
1
10
100
1 k
10 k
t – Time – s
f – Frequency – Hz
Figure 27
Figure 28
TOTAL HARMONIC DISTORTION
TOTAL HARMONIC DISTORTION
vs
vs
FREQUENCY
FREQUENCY
0.6
0.5
0.4
0.3
0.2
0.1
0.3
A
= 10
VD
A
= 2
VD
V
=2V
O(PP)
V
=2V
O(PP)
0.25
0.2
T
A
= 25°C
T
A
= 25°C
0.15
0.1
V
CC±
= ±5 V
V
CC±
= ±5 V
Source Signal
0.5
0
Source Signal
100
0
10
100
1 k
10 k
100 k
10
1 k
10 k
100 k
f – Frequency – Hz
f – Frequency – Hz
Figure 29
Figure 30
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
18
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
UNITY-GAIN BANDWIDTH
vs
UNITY-GAIN BANDWIDTH
vs
FREE-AIR TEMPERATURE
SUPPLY VOLTAGE
2.5
2.5
R
C
T
= 10 kΩ
= 100 pF
= 25°C
L
L
A
V
CC±
= ±15 V
See Figure 3
2
2
V
CC±
= ±5 V
1.5
1.5
R
C
= 10 kΩ
= 100 pF
L
L
See Figure 3
1
– 75 – 50 – 25
1
0
25
50
75
100
0
2
4
6
8
10
12
14
16
T
A
– Free-Air Temperature – °C
|V | – Supply Voltage – V
CC±
Figure 31
Figure 32
PHASE MARGIN
vs
PHASE MARGIN
vs
SUPPLY VOLTAGE
LOAD CAPACITANCE
60°
50°
62°
61°
V
R
= ±15 V
CC±
= 10 kΩ
R
C
= 10 kΩ
= 100 pF
= 25°C
L
L
L
T
= 25°C
A
T
A
See Figure 3
See Figure 3
60°
59°
58°
57°
40°
30°
20°
10°
56°
55°
0°
0
200
400
600
800
1000
0
2
4
6
8
10
12
14
16
C
– Load Capacitance – pF
|V | – Supply Voltage – V
CC±
L
Figure 33
Figure 34
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
19
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
OPERATIONAL AMPLIFIER SECTION
PHASE MARGIN
vs
FREE-AIR TEMPERATURE
66°
64°
62°
R
C
= 10 kΩ
= 100 pF
L
L
See Figure 3
V
CC±
= ±15 V
60°
58°
56°
V
CC±
= ±5 V
54°
– 75
0
25
50
75
100
–50 –25
T
A
– Free-Air Temperature – °C
Figure 35
SHUTDOWN THRESHOLD VOLTAGE
SUPPLY CURRENT
vs
INPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
0.6
0.5
0.4
0.3
0.2
0.1
0
5
I
O
= 0
4
3
2
V
(FB/SD)
1
0
– 50
– 25
0
25
50
75
100
0
5
10
15
T
– Free-Air Temperature – °C
A
V – Input Voltage – V
I
Figure 36
Figure 37
†
Data applies for the amplifier block only; the switched-capacitor block is not supplying V
supply.
CC–
20
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
SWITCHED-CAPACITOR SECTION
SUPPLY CURRENT IN SHUTDOWN
OSCILLATOR FREQUENCY
vs
vs
INPUT VOLTAGE
FREE-AIR TEMPERATURE
120
100
80
60
40
20
0
35
33
31
29
27
25
V
= 0
(FB/SD)
V
= 15 V
CC
V
= 3.5 V
CC
23
21
19
17
15
0
25
50
75
100
– 75 – 50 – 25
0
5
10
15
V – Input Voltage – V
I
T
A
– Free-Air Temperature – °C
Figure 38
Figure 39
OUTPUT VOLTAGE LOSS
vs
INPUT CAPACITANCE
AVERAGE SUPPLY CURRENT
vs
OUTPUT CURRENT
1.4
1.2
1
140
120
100
T
A
= 25°C
I
O
= 100 mA
0.8
0.6
80
60
I
I
= 50 mA
= 10 mA
O
O
0.4
40
Inverter Configuration
COUT = 100-µF Tantalum
0.2
0
20
0
f
= 25 kHz
osc
0
10 20 30 40 50 60 70 80 90 100
0
20
40
60
80
100
C – Input Capacitance – µF
i
I
O
– Output Current – mA
Figure 40
Figure 41
†
Data applies for the switched-capacitor block only. Amplifier block is not connected.
21
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
SWITCHED-CAPACITOR SECTION
OUTPUT VOLTAGE LOSS
vs
OUTPUT VOLTAGE LOSS
vs
OSCILLATOR FREQUENCY
OSCILLATOR FREQUENCY
2.5
2.25
2
2.5
2.25
2
Inverter Configuration
CIN = 100-µF Tantalum
COUT= 100-µF Tantalum
Inverter Configuration
CIN = 10-µF Tantalum
COUT = 100-µF Tantalum
1.75
1.5
1.25
1
1.75
1.5
1.25
1
I
= 100 mA
O
I
= 100 mA
O
I
= 50 mA
O
I
= 50 mA
= 10 mA
O
O
0.75
0.5
0.75
0.5
I
= 10 mA
O
0.25
0
0.25
0
I
1
10
100
1
10
100
f
– Oscillator Frequency – kHz
f
– Oscillator Frequency – kHz
osc
osc
Figure 42
Figure 43
REFERENCE VOLTAGE CHANGE
vs
REGULATED OUTPUT VOLTAGE
vs
FREE-AIR TEMPERATURE
FREE-AIR TEMPERATURE
100
80
– 4.7
– 4.8
SCREF = 2.5 V
= 25°C
T
A
60
40
– 4.9
– 5
20
0
– 5.1
–11.6
– 20
– 40
– 60
–11.8
–12
–12.2
– 80
–12.4
–12.6
– 100
– 50
– 25
0
25
50
75
100
0
25
50
75
100
–50
–25
T
– Free-Air Temperature – °C
T
A
– Free-Air Temperature – °C
A
Figure 44
Figure 45
†
Data applies for the switched-capacitor block only. Amplifier block is not connected.
22
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
†
TYPICAL CHARACTERISTICS
SWITCHED-CAPACITOR SECTION
VOLTAGE LOSS
vs
OUTPUT CURRENT
2
3.5 V ≤ V
CIN = COUT = 100 µF
≤ 15 V
CC
1.8
1.6
1.4
1.2
1
T
A
= 85°C
0.8
0.6
0.4
T
A
= 25°C
0.2
0
0
10 20 30 40 50 60 70
Output Current – mA
80 90 100
Figure 46
†
Data applies for the switched-capacitor block only. Amplifier block is not connected.
23
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
amplifier section
input characteristics
The TLE2662 is specified with a minimum and a maximum input voltage that if exceeded at either input, could
cause the device to malfunction.
Because of the extremely high input impedance and resulting low bias-current requirements, the TLE2662
operational amplifier section is well suited for low-level signal processing; however, leakage currents on printed-
circuit boards and sockets can easily exceed bias-current requirements and cause degradation in system
performance. It is a good practice to include guard rings around inputs (see Figure 47). These guards should
be driven from a low-impedance source at the same voltage level as the common-mode input.
The inputs of any unused amplifiers should be tied to ground to avoid possible oscillation.
V
I
+
–
+
–
V
I
+
–
V
O
V
O
V
O
V
I
Figure 47. Use of Guard Rings
switched-capacitor section
V
CC
SCREF
2.5 V
REF
R
R
Drive
CAP +
+
†
–
CIN
FB/SD
OSC
Q
Q
OSC
CAP –
Drive
Drive
GND
†
COUT
SCOUT
Drive
†
External capacitors
Figure 48. Functional Block Diagram for Switched-Capacitor Block Only
24
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
switched-capacitor section (continued)
The TLE2662, with its high-output-drive amplifiers and switched-capacitor voltage converter, readily lends itself
to applications like headphone drivers where large signal swing into heavy loads is paramount. Another
application is analog-to-digital interfacing when only a single rail is available to the system, but maximization
of the ADC dynamic range is key. See Figure 48 for the functional block diagram of the switched-capacitor block.
typical application
In its most basic configuration, the TLE2662 switched-capacitor section is used as a voltage inverter to provide
the negative rail for the amplifiers in a single-supply system. As shown in Figure 49, the positive 5-V supply is
connected to both V
and SCIN. V
is connected to the output of the charge pump, SCOUT. Only three
CC+
CC–
external components (excluding the resistors used with the amplifiers) are necessary: the storage capacitors,
CIN and COUT, and a fast-recovery Schottky diode to clamp SCOUT during start up. The diode is necessary
because the amplifiers present a load referenced to the positive rail and tends to pull SCOUT above ground,
which can cause the device to fail to start up (see pin functions section in APPLICATION INFORMATION). As
shown in Figure 50, one amplifier is shown driving a resistive load; the other is interfacing to an analog-to-digital
converter (ADC).
R
L
5 V
To ADC
R
F
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
CC+
R
R
F
Signal
From
F
2OUT
2IN–
Preamplifier
R
IN
Signal
From
Transducer
V
CC–
2IN+
Filter
SCOUT
SCREF
OSC
CAP–
GND
CIN
1N4933
+
COUT
CAP+
FB/SD
+
SCIN
Shutdown
Figure 49. Switched-Capacitor Block Supplying Negative Rail for Amplifiers
25
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
typical application (continued)
5 V
R
R
F
F
R
R
I
I
Signal
From
Preamplifier
Signal
From
Transducer
To ADC
Amplifier 2
–
+
–
+
Amplifier 1
R
L
SCIN
SCOUT
Voltage
Converter
FB/SD SCREF
Shutdown
Figure 50. Equivalent Schematic: Amplifier 1 Driving Resistive Load,
Amplifier 2 Interfacing to an ADC
Though simple, this configuration has the inherent disadvantage of having ripple and switching-noise
components on SCOUT. These are coupled into the amplifier’s signal path, effectively introducing distortion into
the output waveform. The effect is most pronounced when the outputs are driven low, loading the negative rail
generatedbythechargepump. AfirstapproachtominimizingtheseeffectsistoincreasethesizeofCOUTusing
a low-ESR type capacitor (refer to the switched-capacitor selection section under capacitor selection and output
ripple). Figures 51 and 52 compare the ripple and noise present at the amplifier output with COUT = 10 µF and
COUT = 100 µF, respectively, with the outputs driven low into a 600-Ω load.
26
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
typical application (continued)
RIPPLE AND SWITCHING NOISE ON
RIPPLE AND SWITCHING NOISE ON
AMPLIFIER OUTPUT
AMPLIFIER OUTPUT
vs
TIME
vs
TIME
V
V
V
+20
+15
+10
+5
V
OL
V
OL
V
OL
V
OL
+80
+60
+40
+20
OL
OL
OL
V
R
= 5 V
= 600 Ω
V
R
= 5 V
= 600 Ω
CC+
L
CC+
L
CIN = 100 µF
COUT = 100 µF
CIN = 100 µF
COUT = 10 µF
V
ID
= –100 mV
V
ID
= –100 mV
V
OL
V
OL
V
OL
V
–5
V
V
–20
OL
OL
V
–10
–15
–20
–40
OL
OL
OL
OL
V
V
V
V
–60
–80
OL
OL
0
10 20 30 40 50 60 70 80 90 100
0
10 20 30 40 50 60 70 80 90 100
t – Time – µs
t – Time – µs
Figure 51
Figure 52
Additional filtering can be added between SCOUT and V
to further reduce ripple and noise. For example,
CC–
adding the simple low-pass LC filter shown in Figure 53, implemented using a 50-µH inductor and 220-µF
capacitor (available in surface mount), results in the reduced levels of ripple and switching noise at the
amplifier’s outputs (see Figures 54 and 55). Larger values of L or C can be used for even better attenuation.
L
H
SCOUT
V
CC
COUT
0.1 µF
C
F
+
1
f =
r
2 π LC
Filter
Figure 53. LC Filter Used to Reduce Ripple and Switching Noise, f = 1/2π√LC, A = –40 dB Per Decade
r
27
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
typical application (continued)
RIPPLE AND SWITCHING NOISE ON
RIPPLE AND SWITCHING NOISE ON
AMPLIFIER OUTPUT
AMPLIFIER OUTPUT
vs
vs
TIME
TIME
V
V
V
V
+8
+6
+4
+2
V
V
V
V
+8
+6
+4
+2
OL
OL
OL
OL
OL
OL
V
R
= 5 V
= 600 Ω
CC+
L
V
R
= 5 V
= 600 Ω
CC+
L
CIN = 100 µF
COUT = 100 µF
CIN = 100 µF
COUT = 10 µF
OL
V
OL
V
OL
–2
OL
–2
V
V
V
V
OL
OL
–4
OL
–4
OL
Filter:
Filter:
L
C
= 50 µH
= 220 µF
L
C
= 50 µH
= 220 µF
F
F
F
F
V
–6
V
–6
OL
OL
OL
OL
See Figure 53
See Figure 53
V
–8
V
–8
0
10 20 30 40 50 60 70 80 90 100
0
10 20 30 40 50 60 70 80 90 100
t – Time – µs
t – Time – µs
Figure 54
Figure 55
28
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
precision measurement techniques
In systems where the amplifier outputs are being sampled by an analog-to-digital converter (ADC), the
switched-capacitornetwork can be temporarily disabled by applying a voltage of less then 0.45 V to FB/SD. This
is easily accomplished using any open-collector gate (shown by dashed lines in Figure 49). When disabled, the
internal switches are set to dump any remaining charge onto COUT. The voltage at SCOUT decays to zero at
a rate dependent on both the size of COUT and loading. During this time, the amplifier’s outputs are free of any
switching-inducedripple and noise. Figure 56 shows the relationship of the output voltage decay time to the size
of the output storage capacitor when one channel of the amplifier is driving a 100-Ω load to ground. SCOUT
rises again when the external gate is turned off (see Figure 57).
OFF-STATE VOLTAGE DECAY AT OUTPUT
TURN-ON VOLTAGE RISE AT OUTPUT
vs
vs
TIME
TIME
6
4
6
4
V
V
= 5 V
= SCOUT
V
= 5 V
CC+
CC+
CC–
V
CC–
= SCOUT
CIN = 100 µF
CIN = 100 µF
R
V
= 100 Ω
R
V
= 100 Ω
L
L
= –100 mV
= –100 mV
ID
ID
2
2
COUT = 22 µF
COUT = 100 µF
0
0
COUT = 100 µF
COUT = 220 µF
– 2
– 4
– 6
– 2
– 4
– 6
COUT = 220 µF
COUT = 22 µF
30 40
0
10
20
30
40
50
60
70
80
0
10
20
50
60
70
80
t – Time – ms
t – Time – ms
Figure 56
Figure 57
The amplifier’s negative input common-mode voltage limit (V
) is specified as an offset from the negative
ICR–
rail. Care should be taken to ensure that the input signal does not violate this limit as SCOUT decays. The
negative output voltage swing is similarly affected by the gradual loss of the negative rail.
This application takes advantage of the otherwise unused SCREF output of the switched-capacitor block to bias
one amplifier to 2.5 V. This is especially useful when the amplifier is followed by an ADC, keeping the signal
centered in the middle of the converter dynamic range. Other biasing methods may be necessary in precision
systems.
In Figure 58, SCREF, R1, and R2 are used to generate a feedback voltage to the TLE2662 error amplifier. This
voltage, fed into FB/SD, is used to regulate the voltage at SCOUT. When used this way, there is higher voltage
loss (SCIN – |SCOUT|) associated with the regulation. For example, the inverter generates an unregulated
voltage of approximately –4.5 V from a positive 5-V source; it can achieve a regulated output voltage of only
about–3.5V.Thoughthisreducestheamplifierinputandoutputdynamicrange,bothV
to below ground.
andV stillextend
ICR–
OL
29
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
precision measurement techniques (continued)
R
L
5 V
To ADC
R
F
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
CC+
R
R
F
I
2OUT
2IN–
R
I
COUT
+
V
CC–
2IN+
+
C1
R2
R1
SCOUT
SCREF
OSC
CAP–
GND
CIN
+
1N4933
CAP+
FB/SD
SCIN
Restart
R3
R4
Shutdown
| SCOUT |
SCREF
R2
R1
1
40 mV
2
Where: SCREF = 2.5 V Nominal
Figure 58. Voltage Inverter With Regulated Output
The reference voltage, though being used as part of the regulation circuitry, is still available for other uses if total
current drawn from it is limited to under 60 µA. The shutdown feature also remains available, though a restart
pulse may be necessary to start the switched-capacitor if the voltage on COUT is not fully discharged. This
restart pulse is isolated from the feedback loop using a blocking diode in the regulation section.
The circuit designer should be aware that the TLE2662 amplifier and switched-capacitor sections are tested
and specified separately. Performance may differ from that shown in the typical characteristics section when
used together. This is evident, for example, in the dependence of V
and V
on V
. The impact of
ICR–
OL
CC–
supplying the amplifier negative rail using the switched-capacitor block in each design should be considered
and carefully evaluated.
The more esoteric features of the switched-capacitor building block, including external synchronization of the
internal oscillator and power dissipation considerations, are covered in detail in the following section.
30
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
switched-capacitor function
A review of a basic switched-capacitor building block is helpful in understanding the operation of the TLE2662.
When the switch shown in Figure 59 is in the left position, capacitor C1 charges to the voltage at V1. The total
charge on C1 is q1 = C1V1. When the switch is moved to the right, C1 is discharged to the voltage at V2. After
this discharge time, the charge on C1 is q2 = C1V2. The charge has been transferred from the source V1 to
the output V2. The amount of charge transferred is as shown in equation 1.
∆q = q1 – q2 = C1(V1 – V2)
If the switch is cycled f times per second, the charge transfer per unit time (i.e., current) is shown in equation 2.
I = f x ∆q = f x C1(V1 – V2)
(2)
(1)
To obtain an equivalent resistance for a switched-capacitor network, this equation can be rewritten in terms of
voltage and impedance equivalence as shown in equation 3.
V1
(1 fC1)
V2
V1
R
V2
I
(3)
EQUIV
V1
V2
f
R
L
C1
C2
Figure 59. Switched-Capacitor Block
,isdefinedasR =1÷fC1.Theequivalentcircuitfortheswitched-capacitornetwork
Anewvariable,R
EQUIV
EQUIV
is as shown in Figure 60. The TLE2662 has the same switching action as the basic switched-capacitor voltage
converter. Even though this simplification does not include finite switch-on resistance and output-voltage ripple,
it provides an insight into how the device operates.
These simplified circuits explain voltage loss as a function of oscillator frequency (see Figure 43). As oscillator
frequency is decreased, the output impedance is eventually dominated by the 1/fC1 term and voltage losses
rise.
Voltage losses also rise as oscillator frequency increases. This is caused by internal switching losses that occur
due to some finite charge being lost on each switching cycle. This charge loss per-unit-cycle, when multiplied
by the switching frequency, becomes a current loss. At high frequency, this loss becomes significant and voltage
losses again rise. The oscillator of the TLE2662 switched-capacitor section is designed to run in the frequency
band where voltage losses are at a minimum.
R
EQUIV
V1
V2
C2
R
L
1
R
=
EQUIV
fC1
Figure 60. Switched-Capacitor Equivalent Circuit
31
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
pin functions (see functional block diagram – converter)
Supply voltage (SCIN) alternately charges CIN to the input voltage when CIN is switched in parallel with the
input supply, and then transfers charge to COUT when CIN is switched in parallel with COUT. Switching
occurs at the oscillator frequency. During the time that CIN is charging, the peak supply current is
approximately 2.2 times the output current. During the time that CIN is delivering a charge to COUT, the
supply current drops to approximately 0.2 times the output current. An input supply bypass capacitor supplies
part of the peak input current drawn by the TLE2662 switched-capacitor section and averages out the current
drawn from the supply. A minimum input supply bypass capacitor of 2 µF, preferably tantalum or some other
low-ESR type, is recommended. A larger capacitor is desirable in some cases. An example is when the actual
input supply is connected to the TLE2662 through long leads or when the pulse currents drawn by the
TLE2662 might affect other circuits through supply coupling.
In addition to being the output pin, SCOUT is tied to the substrate of the device. Special care must be taken in
TLE2662 circuits to avoid making SCOUT positive with respect to any of the other pins. For circuits with the
output load connected from V
external Schottky diode must be added (see Figure 61). This diode prevents SCOUT from being pulled above
to SCOUT or from some external positive supply voltage to SCOUT, an
CC+
the GND during start up. A fast-recovery diode such as IN4933 with low forward voltage (V ≈ 0.2 V) can be
f
used.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
+
CC
2OUT
2IN–
V
CC–
2IN+
SCOUT
SCREF
OSC
CAP–
GND
SCOUT
COUT
IN4933
CIN
+
+
CAP+
FB/SD
SCIN
Load
V
CC+
or External Supply Voltage
Figure 61. Circuit With Load Connected From V
to SCOUT
CC
The voltage reference (SCREF) output provides a 2.5-V reference point for use in TLE2662-based regulator
circuits. The temperature coefficient (TC) of the reference voltage has been adjusted so that the TC of the
regulated output voltage is near zero. As seen in the typical performance curves, this requires the reference
output to have a positive TC. This nonzero drift is necessary to offset a drift term inherent in the internal
reference divider and comparator network tied to the feedback pin. The overall result of these drift terms is a
regulated output that has a slight positive TC at output voltages below 5 V and a slight negative TC at output
voltages above 5 V. For regulator-feedback networks, reference output current should be limited to
approximately 60 µA. SCREF draws approximately 100 µA when shorted to ground and does not affect the
internal reference/regulator. This pin can also be used as a pullup for TLE2662 circuits that require
synchronization.
32
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
pin functions (continued)
CAP+ is the positive side of input capacitor (CIN) and is alternately driven between V
and ground. When
CC
driven to V , CAP+ sources current from V . When driven to ground, CAP+ sinks current to ground. CAP–
CC
CC
is the negative side of the input capacitor and is driven alternately between ground and SCOUT. When driven
to ground, CAP– sinks current to ground. When driven to SCOUT, CAP– sources current from COUT. In all
cases, current flow in the switches is unidirectional as should be expected when using bipolar switches.
OSC can be used to raise or lower the oscillator frequency or to synchronize the device to an external clock.
Internally, OSC is connected to the oscillator timing capacitor (C ≈ 150 pF), which is alternately charged and
t
discharged by current sources of ±7 µA, so that the duty cycle is approximately 50%. The TLE2662
switched-capacitor section oscillator is designed to run in the frequency band where switching losses are
minimized. However, the frequency can be raised, lowered, or synchronized to an external system clock if
necessary.
The frequency can be increased by adding an external capacitor (C2 in Figure 62) in the range of 5 pF–20 pF
from CAP+ to OSC. This capacitor couples a charge into C at the switch transitions. This shortens the charge
t
and discharge time and raises the oscillator frequency. Synchronization can be accomplished by adding an
external pullup resistor from OSC to SCREF. A 20-kΩ pullup resistor is recommended. An open-collector gate
or an npn transistor can then be used to drive OSC at the external clock frequency as shown in Figure 62. The
frequency can be lowered by adding an external capacitor (C in Figure 62) from OSC to ground. This increases
1
the charge and discharge times, which lowers the oscillator frequency.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
+
CC
2OUT
2IN–
V
CC–
2IN+
COUT
C1
SCOUT
SCREF
OSC
CAP–
GND
+
CIN
+
CAP+
FB/SD
SCIN
SCIN
C2
Figure 62. External Clock System
The feedback/shutdown (FB/SD) pin has two functions. Pulling FB/SD below the shutdown threshold (≈ 0.45 V)
puts the device into shutdown. In shutdown, the reference/regulator is turned off and switching stops. The
switches are set such that both CIN and COUT are discharged through the output load. Quiescent current in
shutdown drops to approximately 100 µA . Any open-collector gate can be used to put the TLE2662 into
shutdown. For normal (unregulated) operation, the device restarts when the external gate is shut off. In
TLE2662 circuits that use the regulation feature, the external resistor divider can provide enough pulldown to
keep the device in shutdown until the output capacitor (COUT) has fully discharged. For most applications
33
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
where the TLE2662 is run intermittently, this does not present a problem because the discharge time of the
output capacitor is short compared to the off time of the device. In applications where the device has to start-up
before the output capacitor (COUT) has fully discharged, a restart pulse must be applied to FB/SD of the
TLE2662.
Using the circuit shown in Figure 63, the restart signal can be either a pulse (t > 100 µs) or a logic high. Diode
p
coupling the restart signal into FB/SD allows the output voltage to rise and regulate without overshoot. The
resistor divider R3/R4 shown in Figure 63 should be chosen to provide a signal level at FB/SD of 0.7 V–1.1 V.
FB/SD is also the inverting input of the TLE2662 switched-capacitor section error amplifier, and as such can
be used to obtain a regulated output voltage.
COUT
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
+
100 µF Tantalum
CC
+
2OUT
2IN–
C1
+
SCOUT
R2
V
CC–
2IN+
SCOUT
SCREF
OSC
CAP–
GND
CIN
R1
10 µF
+
Tantalum
CAP+
FB/SD
SCIN
SCIN
R3
R4
+
2.2 µF
| SCOUT |
R2
R1
1
SCREF
2
40 mV
Shutdown
Restart
Where: SCREF = 2.5 V Nominal
Figure 63. Basic Regulation Configuration
regulation
TheerroramplifieroftheTLE2662switched-capacitorsectiondrivesthenpnswitchtocontrolthevoltageacross
the input capacitor (CIN), which determines the output voltage. When the reference and error amplifier of the
TLE2662 is used, an external resistive divider is all that is needed to set the regulated output voltage. Figure 63
shows the basic regulator configuration and the formula for calculating the appropriate resistor values. R1
should be 20 kΩ or greater because the reference current is limited to ±100 µA. R2 should be in the range of
100 kΩ to 300 kΩ. Frequency compensation is accomplished by adjusting the ratio of CIN to COUT. For best
results, this ratio should be approximately 1 to 10. Capacitor C1, required for good load regulation, should be
0.002 µF for all output voltages.
34
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
regulation (continued)
The functional block diagram shows that the maximum regulated output voltage is limited by the supply voltage.
For the basic configuration, SCOUT referenced to GND of the TLE2662 must be less than the total of the
supply voltage minus the voltage loss due to the switches. The voltage loss versus output current due to the
switches can be found in the typical performance curves.
capacitor selection
While the exact values of CIN and COUT are noncritical, good-quality low-ESR capacitors such as solid
tantalum are necessary to minimize voltage losses at high currents. For CIN, the effect of the equivalent series
resistance (ESR) of the capacitor is multiplied by four, since switch currents are approximately two times higher
than output current. Losses occur on both the charge and discharge cycle, which means that a capacitor with
1 Ω of ESR for CIN has the same effect as increasing the output impedance of the switched-capacitor section
by4Ω. Thisrepresentsasignificantincreaseinthevoltagelosses. COUTisalternatelychargedanddischarged
at a current approximately equal to the output current. The ESR of the capacitor causes a step function to occur
in the output ripple at the switch transitions. This step function degrades the output regulation for changes in
output load current and should be avoided. A technique used is to parallel a smaller tantalum capacitor with a
large aluminum electrolytic capacitor to gain both low ESR and reasonable cost.
output ripple
The peak-to-peak output ripple is determined by the output capacitor and the output current values.
Peak-to-peak output ripple is approximated as shown in equation 4:
I
O
(4)
V
2 fC
O
where:
∆V = peak-to-peak ripple
= oscillator frequency
f
OSC
For output capacitors with significant ESR, a second term must be added to account for the voltage step at the
switch transitions. This step is approximately equal to equation 5:
2I
ESR of C
(5)
O
O
power dissipation (switched-capacitor section only)
The power dissipation of any TLE2662 circuit must be limited so that the junction temperature of the device does
not exceed the maximum junction temperature ratings. The total power dissipation is calculated from two
components, thepowerlossduetovoltagedropsintheswitches, andthepowerlossduetodrivecurrentlosses.
The total power dissipated by the TLE2662 is calculated as shown in equation 6:
(6)
P
(V
–
V
) I
(V ) (I ) (0.2)
CC
CC
O
O
O
where both V
and SCOUT refer to GND. The power dissipation is equivalent to that of a linear regulator. Due
CC
to limitations of the DW package, steps must be taken to dissipate power externally for large input or output
differentials. This is accomplished by placing a resistor in series with CIN as shown in Figure 64. A portion of
the input voltage is dropped across this resistor without affecting the output regulation. Since switch current is
approximately 2.2 times the output current and the resistor causes a voltage drop when CIN is both charging
and discharging, the resistor chosen is as shown in equation 7.
35
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
power dissipation (continued)
R
V
(4.4 I )
X
O
(7)
X
where:
V
V
– (TLE2662 voltage loss) (1.3)
V
X
CC
O
and I
= maximum required output current. The factor of 1.3 allows some operating margin for the TLE2662.
OUT
When using a 12-V to –5-V converter at 100-mA output current, calculate the power dissipation without an
external resistor as shown in equation 8.
|
|
P
P
(12 V
5 V ) (100 mA)
(12 V) (100 mA) (0.2)
(8)
700 mW
240 mW
940 mW
1
2
3
4
5
6
7
8
16
1OUT
1IN–
1IN+
V
+
CC
COUT
+
15
14
13
12
11
10
9
2OUT
2IN–
C1
+
SCOUT
R2
V
CC–
2IN+
SCOUT
SCREF
OSC
CAP–
GND
R1
CIN
+
CAP+
FB/SD
Rx
SCIN
+
SCIN
Figure 64. Power-Dissipation-Limiting Resistor in Series With CIN
At θ of 130°C/W for a commercial plastic device, a junction temperature rise of 122°C is seen. The device
JA
exceeds the maximum junction temperature at an ambient temperature of 25°C. To calculate the power
dissipation with an external-resistor (R ), determine how much voltage can be dropped across R . The
X
X
maximum voltage loss of the TLE2662 in the standard regulator configuration at 100 mA output current is 1.6 V
(see equation 9).
V
12 V
(1.6 V) (1.3)
–5 V
4.9 V
(9)
X
and
R
4.9 V (4.4) (100 mA)
11
X
36
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
power dissipation (continued)
The resistor reduces the power dissipated by the TLE2662 by (4.9 V) (100 mA) = 490 mW. The total power
dissipated by the TLE2662 is equal to (940 mW – 490 mW) = 450 mW. The junction temperature rise is 58°C.
Although commercial devices are functional up to a junction temperature of 125°C, the specifications are tested
to a junction temperature of 100°C. In this example, this means limiting the ambient temperature to 42°C. To
allow higher ambient temperatures, the thermal resistance numbers for the TLE2662 packages represent
worst-case numbers with no heat sinking and still air. Small clip-on heat sinks can be used to lower the thermal
resistance of the TLE2662 package. Airflow in some systems helps to lower the thermal resistance. Wide PC
board traces from the TLE2662 leads helps to remove heat from the device. This is especially true for plastic
packages.
basic voltage inverter
The switched-capacitor block is connected as a basic voltage inverter with regulation as shown in Figure 65.
The magnitude of SCIN must exceed that of the desired SCOUT to accommodate voltage losses due to
switching and regulation. Losses of 1 V to 2 V are typical.
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
100 µF
1OUT
1IN–
1IN+
V
+
CC
+
2OUT
2IN–
0.002 µF
+
SCOUT
R2
V
CC–
2IN+
SCOUT
SCREF
OSC
CAP–
GND
R1
10 µF
+
CAP+
FB/SD
SCIN
SCIN
+
2 µF
| SCOUT |
| SCOUT |
1.121 V
R2
R1
1
R1
1
SCREF
2
40 mV
Figure 65. Basic Voltage Inverter/Regulator
37
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
TLE2662
DUAL µPOWER JFET-INPUT OPERATIONAL AMPLIFIER
WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
SLOS118B – DECEMBER 1992 – REVISED AUGUST 1994
APPLICATION INFORMATION
positive voltage doubler
In this configuration (see Figure 66), the voltage converter is configured as a positive voltage doubler providing a
higher positive rail, approximately 9 V for the amplifiers or other external circuitry. Filtering (not shown) of the output
of the doubler may be necessary.
Output
Signal
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
1OUT
1IN–
1IN+
V
+
CC
R
F
R
R
2OUT
2IN–
R
IN
Input
Signal
V
CC–
2IN+
SCOUT
SCREF
OSC
CAP–
GND
CAP+
FB/SD
10 µF
5 V
SCIN
+
V
O
+
1N4001
1N4001
+
2 µF
100 µF
Figure 66. Voltage Converter Configured as Positive Doubler
38
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
30-Mar-2005
PACKAGING INFORMATION
Orderable Device
Status (1)
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
SOIC
SOIC
Drawing
TLE2662IDW
OBSOLETE
OBSOLETE
DW
16
16
TBD
TBD
Call TI
Call TI
Call TI
Call TI
TLE2662IDWR
DW
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan
-
The planned eco-friendly classification: Pb-Free (RoHS) or Green (RoHS
&
no Sb/Br)
-
please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications,
enhancements, improvements, and other changes to its products and services at any time and to discontinue
any product or service without notice. Customers should obtain the latest relevant information before placing
orders and should verify that such information is current and complete. All products are sold subject to TI’s terms
and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in
accordance with TI’s standard warranty. Testing and other quality control techniques are used to the extent TI
deems necessary to support this warranty. Except where mandated by government requirements, testing of all
parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for
their products and applications using TI components. To minimize the risks associated with customer products
and applications, customers should provide adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right,
copyright, mask work right, or other TI intellectual property right relating to any combination, machine, or process
in which TI products or services are used. Information published by TI regarding third-party products or services
does not constitute a license from TI to use such products or services or a warranty or endorsement thereof.
Use of such information may require a license from a third party under the patents or other intellectual property
of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of information in TI data books or data sheets is permissible only if reproduction is without
alteration and is accompanied by all associated warranties, conditions, limitations, and notices. Reproduction
of this information with alteration is an unfair and deceptive business practice. TI is not responsible or liable for
such altered documentation.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that
product or service voids all express and any implied warranties for the associated TI product or service and
is an unfair and deceptive business practice. TI is not responsible or liable for any such statements.
Following are URLs where you can obtain information on other Texas Instruments products and application
solutions:
Products
Applications
Audio
Amplifiers
amplifier.ti.com
www.ti.com/audio
Data Converters
dataconverter.ti.com
Automotive
www.ti.com/automotive
DSP
dsp.ti.com
Broadband
Digital Control
Military
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/military
Interface
Logic
interface.ti.com
logic.ti.com
Power Mgmt
Microcontrollers
power.ti.com
Optical Networking
Security
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
microcontroller.ti.com
Telephony
Video & Imaging
Wireless
www.ti.com/wireless
Mailing Address:
Texas Instruments
Post Office Box 655303 Dallas, Texas 75265
Copyright 2005, Texas Instruments Incorporated
相关型号:
TLE2662IDWR
DUAL uPOWER JFET-INPUT OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TI
TLE2682
HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TI
TLE2682IDW
High-Speed JFET-Input Dual Operational Amplifier w/Switched-Capacitor Voltage Converter 16-SOIC
TI
TLE2682IDWR
HIGH-SPEED JFET-INPUT DUAL OPERATIONAL AMPLIFIER WITH SWITCHED-CAPACITOR VOLTAGE CONVERTER
TI
©2020 ICPDF网 联系我们和版权申明