TPS54622 [TI]
4.5V to 17V Input, 6A Synchronous Step Down SWIFT? Converter With Hiccup; 4.5V至17V输入, 6A同步降压SWIFT ™转换器随着打嗝型号: | TPS54622 |
厂家: | TEXAS INSTRUMENTS |
描述: | 4.5V to 17V Input, 6A Synchronous Step Down SWIFT? Converter With Hiccup |
文件: | 总36页 (文件大小:1195K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
4.5V to 17V Input, 6A Synchronous Step Down SWIFT™ Converter With Hiccup
Check for Samples: TPS54622
1
FEATURES
and Overvoltage
•
•
•
Adjustable Input Undervoltage Lockout
•
•
•
•
•
•
•
•
Integrated 26mΩ / 19mΩ MOSFETs
Supported by SwitcherPro™ Software Tool
Split Power Rail: 1.6V to 17V on PVIN
200kHz to 1.6MHz Switching Frequency
Synchronizes to External Clock
For SWIFT™ Documentation and
SwitcherPro™, visit http://www.ti.com/swift
0.6V ±1% Voltage Reference Over Temperature
Low 2uA Shutdown Quiescent Current
Monotonic Start-Up into Pre-biased Outputs
APPLICATIONS
•
•
•
High Density Distributed Power Systems
High Performance Point of Load Regulation
–40°C to 150°C Operating Junction
Temperature Range
Broadband, Networking and Optical
Communications Infrastructure
•
•
Adjustable Slow Start/Power Sequencing
Power Good Output Monitor for Undervoltage
DESCRIPTION
The TPS54622 in thermally enhanced 3.5mm x 3.5mm QFN package is a full featured 17V, 6A synchronous step
down converter which is optimized for small designs through high efficiency and integrating the high-side and
low-side MOSFETs. Further space savings are achieved through current mode control, which reduces
component count, and by selecting a high switching frequency, reducing the inductor's footprint.
The output voltage startup ramp is controlled by the SS/TR pin which allows operation as either a stand alone
power supply or in tracking situations. Power sequencing is also possible by correctly configuring the enable and
the open drain power good pins.
Cycle by cycle current limiting on the high-side FET protects the device in overload situations and is enhanced
by a low-side sourcing current limit which prevents current runaway. There is also a low-side sinking current limit
which turns off the low-side MOSFET to prevent excessive reverse current. Hiccup protection will be triggered if
the overcurrent condition has persisted for longer than the preset time. Thermal hiccup protection disables the
device when the die temperature exceeds the thermal shutdown temperature and enables the part again after
the built-in thermal shutdown hiccup time.
WHITE SPACE
SIMPLIFIED SCHEMATIC
100
PVIN
VIN
VIN
95
90
Cboot
TPS54622
BOOT
Cin
85
80
75
70
65
60
55
50
VIN = 8 V
VIN = 12 V
VOUT
Lo
EN
PH
VIN = 17 V
Co
PWRGD
R1
VSENSE
SS/TR
R2
RT/CLK
COMP
GND
R3
C1
0
1
2
3
4
5
6
Exposed
Thermal
Pad
Css
Rrt C2
Output Current - A
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2011, Texas Instruments Incorporated
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
These devices have limited built-in ESD protection. The leads should be shorted together or the device placed in conductive foam
during storage or handling to prevent electrostatic damage to the MOS gates.
ORDERING INFORMATION(1)
TJ
PACKAGE
PART NUMBER
TPS54622RHLT
TPS54622RHLR
Small Reel(2)
Large Reel(2)
–40°C to 150°C
14 Pin QFN
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) See the application section of the datasheet for layout information.
ABSOLUTE MAXIMUM RATINGS(1)
over operating temperature range (unless otherwise noted)
VALUE
–0.3 to 20
–0.3 to 20
–0.3 to 6
–0.3 to 27
–0.3 to 3
–0.3 to 3
–0.3 to 6
–0.3 to 3
–0.3 to 6
0 to 7.5
UNIT
V
VIN
PVIN
V
EN
V
BOOT
V
Input Voltage
VSENSE
COMP
V
V
PWRGD
SS/TR
V
V
RT/CLK
BOOT-PH
PH
V
V
Output Voltage
–1 to 20
–3 to 20
–0.2 to 0.2
±100
V
PH 10ns Transient
V
Vdiff (GND to exposed thermal pad)
V
RT/CLK
PH
µA
A
Source Current
Current Limit
Current Limit
Current Limit
±200
PH
A
PVIN
A
Sink Current
COMP
PWRGD
µA
mA
kV
V
–0.1 to 5
2
Electrostatic Discharge (HBM) QSS 009-105 (JESD22-A114A)
Electrostatic Discharge (CDM) QSS 009-147 (JESD22-C101B.01)
Operating Junction Temperature
500
–40 to 150
–65 to 150
°C
°C
Storage Temperature
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
2
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
THERMAL INFORMATION
TPS54622
QFN
14 PINS
47.2
THERMAL METRIC(1)(2)
UNITS
θJA
Junction-to-ambient thermal resistance
θJA
Junction-to-ambient thermal resistance(3)
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
32
θJCtop
θJB
64.8
14.4
°C/W
ψJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
0.5
ψJB
14.7
θJCbot
3.2
(1) For more information about traditional and new thermal metrics, see the IC Package Thermal Metrics application report, SPRA953.
(2) Power rating at a specific ambient temperature TA should be determined with a junction temperature of 150°C. This is the point where
distortion starts to substantially increase. Thermal management of the PCB should strive to keep the junction temperature at or below
150°C for best performance and long-term reliability. See power dissipation estimate in application section of this data sheet for more
information.
(3) Test board conditions:
(a) 2.5 inches × 2.5 inches, 4 layers, thickness: 0.062 inch
(b) 2 oz. copper traces located on the top of the PCB
(c) 2 oz. copper ground planes on the 2 internal layers and bottom layer
(d) 4 0.010 inch thermal vias located under the device package
ELECTRICAL CHARACTERISTICS
TJ = –40°C to 150°C, VIN = 4.5V to 17V, PVIN = 1.6V to 17V (unless otherwise noted)
PARAMETER
SUPPLY VOLTAGE (VIN AND PVIN PINS)
PVIN operating input voltage
VIN operating input voltage
VIN internal UVLO threshold
VIN internal UVLO hysteresis
VIN shutdown supply Current
VIN operating – non switching supply current
ENABLE AND UVLO (EN PIN)
Enable threshold
TEST CONDITIONS
MIN
TYP
MAX
UNIT
1.6
4.5
17
17
V
V
VIN rising
4.0
150
2
4.5
V
mV
μA
μA
EN = 0 V
5
VSENSE = 810 mV
600
800
Rising
1.21
1.17
1.15
3.3
1.26
V
Enable threshold
Falling
1.10
Input current
EN = 1.1 V
EN = 1.3 V
μA
μA
Hysteresis current
VOLTAGE REFERENCE
Voltage reference
0 A ≤ IOUT ≤ 6 A
0.594
0.6
0.606
V
MOSFET
High-side switch resistance
High-side switch resistance(1)
Low-side Switch Resistance(1)
ERROR AMPLIFIER
BOOT-PH = 3 V
BOOT-PH = 6 V
VIN = 12 V
32
26
19
60
40
30
mΩ
mΩ
mΩ
Error amplifier Transconductance (gm)
Error amplifier dc gain
–2 μA < ICOMP < 2 μA, V(COMP) = 1 V
1300
3100
μMhos
VSENSE = 0.8 V
1000
V/V
V(COMP) = 1 V, 100 mV input
overdrive
Error amplifier source/sink
±110
μA
Start switching threshold
COMP to Iswitch gm
CURRENT LIMIT
0.25
16
V
A/V
(1) Measured at pins
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
TJ = –40°C to 150°C, VIN = 4.5V to 17V, PVIN = 1.6V to 17V (unless otherwise noted)
PARAMETER
High-side switch current limit threshold
Low-side switch sourcing current limit
Low-side switch sinking current limit
Hiccup wait time
TEST CONDITIONS
MIN
8
TYP
11
MAX
14
UNIT
A
6.5
2
10
15
A
3
4
A
512
16384
Cycles
Cycles
Hiccup time before re-start
THERMAL SHUTDOWN
Thermal shutdown
160
175
10
°C
°C
Thermal shutdown hysteresis
Thermal shutdown hiccup time
16384
Cycles
TIMING RESISTOR AND EXTERNAL CLOCK (RT/CLK PIN)
Minimum switching frequency
Switching frequency
Rrt = 240 kΩ (1%)
160
400
200
480
1600
20
240
560
kHz
kHz
kHz
ns
Rrt = 100 kΩ (1%)
Rrt = 29 kΩ (1%)
Maximum switching frequency
Minimum pulse width
1440
1760
RT/CLK high threshold
RT/CLK low threshold
2
V
0.8
V
Measure at 500 kHz with RT resistor
in series
RT/CLK falling edge to PH rising edge delay
66
ns
Switching frequency range (RT mode set point
and PLL mode)
200
1600
145
kHz
PH (PH PIN)
Measured at 90% to 90% of VIN,
25°C, IPH = 2A
Minimum on time
94
0
ns
ns
Minimum off time
BOOT-PH ≥ 3 V
BOOT (BOOT PIN)
BOOT-PH UVLO
2.1
3
V
SLOW START AND TRACKING (SS/TR PIN)
SS charge current
2.3
20
μA
SS/TR to VSENSE matching
POWER GOOD (PWRGD PIN)
VSENSE threshold
V(SS/TR) = 0.4 V
60
mV
VSENSE falling (Fault)
92
94
% Vref
% Vref
% Vref
% Vref
nA
VSENSE rising (Good)
VSENSE rising (Fault)
VSENSE falling (Good)
Output high leakage
106
104
30
VSENSE = Vref, V(PWRGD) = 5.5 V
I(PWRGD) = 2 mA
100
0.3
1
Output low
V
Minimum VIN for valid output
Minimum SS/TR voltage for PWRGD
V(PWRGD) < 0.5V at 100 μA
0.6
V
1.4
V
4
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
DEVICE INFORMATION
PIN ASSIGNMENTS
RHL PACKAGE
(TOP VIEW)
RT/CLK
1
PWRGD
14
GND 2
GND 3
PVIN 4
PVIN 5
VIN 6
13 BOOT
12 PH
Exposed
Thermal Pad
(15)
11 PH
10 EN
9 SS/TR
8
7
VSENSE
COMP
PIN FUNCTIONS
PIN
DESCRIPTION
NAME
#
RT/CLK
1
Automatically selects between RT mode and CLK mode. An external timing resistor adjusts the switching
frequency of the device; In CLK mode, the device synchronizes to an external clock.
GND
2, 3
4, 5
6
Return for control circuitry and low-side power MOSFET.
Power input. Supplies the power switches of the power converter.
Supplies the control circuitry of the power converter.
Inverting input of the gm error amplifier.
PVIN
VIN
VSENSE
COMP
7
8
Error amplifier output, and input to the output switch current comparator. Connect frequency compensation to this
pin.
SS/TR
9
Slow-start and tracking. An external capacitor connected to this pin sets the internal voltage reference rise time.
The voltage on this pin overrides the internal reference. It can be used for tracking and sequencing.
EN
10
Enable pin. Float to enable. Adjust the input undervoltage lockout with two resistors.
PH
11, 12 The switch node.
BOOT
13
14
15
A bootstrap cap is required between BOOT and PH. The voltage on this cap carries the gate drive voltage for the
high-side MOSFET.
PWRGD
Power Good fault pin. Asserts low if output voltage is low due to thermal shutdown, dropout, over-voltage, EN
shutdown or during slow start.
Exposed
Thermal
PAD
Thermal pad of the package and signal ground and it must be soldered down for proper operation.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
FUNCTIONAL BLOCK DIAGRAM
VIN
PVIN PVIN
PWRGD
EN
Thermal
Hiccup
UVLO
Shutdown
Enable
Comparator
Ip
Ih
Shutdown
Shutdown
Logic
UV
OV
Logic
Hiccup
Shutdown
Enable
Threshold
Boot
Charge
Current
Sense
Minimum Clamp
Pulse Skip
ERROR
AMPLIFIER
VSENSE
SS/TR
BOOT
Boot
UVLO
HS MOSFET
Current
Comparator
Voltage
Reference
Power Stage
& Deadtime
Control
Logic
PH
PH
Slope
Compensation
VIN
Regulator
Hiccup
Shutdown
LS MOSFET
Current Limit
Oscillator
with PLL
Maximum
Clamp
Overload
Recovery
Current
Sense
GND
GND
COMP
RT/CLK
EXPOSED THERMAL PAD
6
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
TYPICAL CHARACTERISTICS
CHARACTERISTIC CURVES
HIGH-SIDE RDS(on) vs TEMPERATURE
LOW-SIDE RDS(on) vs TEMPERATURE
40
35
30
25
20
30
27
24
21
18
15
VIN = 12 V
VIN = 12 V
−50
−25
0
T
25
50
75
100
125
150
−50
−25
0
T
25
50
75
100
125
150
− Junction Temperature − °C
− Junction Temperature − °C
J
J
Figure 1.
Figure 2.
VOLTAGE REFERENCE vs TEMPERATURE
OSCILLATOR FREQUENCY vs TEMPERATURE
0.606
0.604
0.602
0.600
0.598
0.596
0.594
485
480
475
470
465
RT = 100 kΩ
−50
−25
0
T
25
50
75
100
125
150
−50
−25
0
T
25
50
75
100
125
150
− Junction Temperature − °C
− Junction Temperature − °C
J
J
Figure 3.
Figure 4.
SHUTDOWN QUIESCENT CURRENT vs
INPUT VOLTAGE
EN PIN HYSTERESIS CURRENT vs TEMPERATURE
Figure 5.
Figure 6.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
PIN PULL-UP CURRENT vs TEMPERATURE
PIN UVLO THRESHOLD vs TEMPERATURE
1.220
1.215
1.210
1.205
1.200
VIN = 12 V
−50
−25
0
T
25
50
75
100
125
150
°C
− Junction Temperature − °C
J
Figure 7.
Figure 8.
NON-SWITCHING OPERATING QUIESCENT CURRENT
(VIN) vs
INPUT VOLTAGE
SLOW START CHARGE CURRENT vs
TEMPERATURE
2.5
2.4
2.3
2.2
2.1
800
T
= −40°C
J
700
600
500
400
T
= −25°C
J
T
= 150°C
J
−50
−25
0
T
25
50
75
100
125
150
3
6
9
12
15
− Junction Temperature − °C
J
V − Input Voltage − V
I
Figure 9.
Figure 10.
(SS/TR - VSENSE) OFFSET vs TEMPERATURE
PWRGD THRESHOLD vs TEMPERATURE
0.040
0.030
0.020
0.010
120
110
Vin = 12 V
VSENSE Rising
VSENSE Falling
VSENSE Rising
100
90
VSENSE Falling
80
−50
−25
0
T
25
50
75
100
125
150
−50
−25
0
T
25
50
75
100
125
150
− Junction Temperature − °C
− Junction Temperature − °C
J
J
Figure 11.
Figure 12.
8
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
TYPICAL CHARACTERISTICS (continued)
HIGH-SIDE CURRENT LIMIT THRESHOLD vs
INPUT VOLTAGE
MINIMUM CONTROLLABLE ON TIME vs
TEMPERATURE
140
130
120
110
100
13
12
11
10
9
T
= −40°C
J
T
= 25°C
J
T
= 150°C
J
8
7
90
80
6
VIN = 12 V
125 150
5
−50
−25
0
T
25
50
75
100
1
5
9
13
17
− Junction Temperature − °C
V − Input Voltage − V
I
J
Figure 13.
Figure 14.
MINIMUM CONTROLLABLE DUTY RATIO vs
JUNCTION TEMPERATURE
BOOT-PH UVLO THRESHOLD vs TEMPERATURE
7.0
6.0
5.0
4.0
RT = 100 kΩ
VIN = 12 V
°C
Figure 15.
Figure 16.
OVERVIEW
The device is a 17-V, 6-A, synchronous step-down (buck) converter with two integrated n-channel MOSFETs. To
improve performance during line and load transients the device implements a constant frequency, peak current
mode control which also simplifies external frequency compensation. The wide switching frequency of 200 kHz to
1600 kHz allows for efficiency and size optimization when selecting the output filter components. The switching
frequency is adjusted using a resistor to ground on the RT/CLK pin. The device also has an internal phase lock
loop (PLL) controlled by the RT/CLK pin that can be used to synchronize the switching cycle to the falling edge
of an external system clock.
The device has been designed for safe monotonic startup into pre-biased loads. The default start up is when VIN
is typically 4.0V. The EN pin has an internal pull-up current source that can be used to adjust the input voltage
under voltage lockout (UVLO) with two external resistors. In addition, the EN pin can be floating for the device to
operate with the internal pull-up current. The total operating current for the device is approximately 600μA when
not switching and under no load. When the device is disabled, the supply current is typically less than 2μA.
The integrated MOSFETs allow for high efficiency power supply designs with continuous output currents up to 6
amperes. The MOSFETs have been sized to optimize efficiency for lower duty cycle applications.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
TYPICAL CHARACTERISTICS (continued)
The device reduces the external component count by integrating the boot recharge circuit. The bias voltage for
the integrated high-side MOSFET is supplied by a capacitor between the BOOT and PH pins. The boot capacitor
voltage is monitored by a BOOT to PH UVLO (BOOT-PH UVLO) circuit allowing PH pin to be pulled low to
recharge the boot capacitor. The device can operate at 100% duty cycle as long as the boot capacitor voltage is
higher than the preset BOOT-PH UVLO threshold which is typically 2.1V. The output voltage can be stepped
down to as low as the 0.6V voltage reference (Vref).
The device has a power good comparator (PWRGD) with hysteresis which monitors the output voltage through
the VSENSE pin. The PWRGD pin is an open drain MOSFET which is pulled low when the VSENSE pin voltage
is less than 92% or greater than 106% of the reference voltage Vref and asserts high when the VSENSE pin
voltage is 94% to 104% of the Vref.
The SS/TR (slow start/tracking) pin is used to minimize inrush currents or provide power supply sequencing
during power up. A small value capacitor or resistor divider should be coupled to the pin for slow start or critical
power supply sequencing requirements.
The device is protected from output overvoltage, overload and thermal fault conditions. The device minimizes
excessive output overvoltage transients by taking advantage of the overvoltage circuit power good comparator.
When the overvoltage comparator is activated, the high-side MOSFET is turned off and prevented from turning
on until the VSENSE pin voltage is lower than 104% of the Vref. The device implements both high-side MOSFET
overload protection and bidirectional low-side MOSFET overload protections which help control the inductor
current and avoid current runaway. The device also shuts down if the junction temperature is higher than thermal
shutdown trip point. The device is restarted under control of the slow start circuit automatically after the built-in
thermal shutdown hiccup time.
DETAILED DESCRIPTION
Fixed Frequency PWM Control
The device uses a adjustable fixed frequency, peak current mode control. The output voltage is compared
through external resistors on the VSENSE pin to an internal voltage reference by an error amplifier which drives
the COMP pin. An internal oscillator initiates the turn on of the high-side power switch. The error amplifier output
is converted into a current reference which compares to the high-side power switch current. When the power
switch current reaches current reference generated by the COMP voltage level the high-side power switch is
turned off and the low-side power switch is turned on.
Continuous Current Mode Operation (CCM)
As a synchronous buck converter, the device normally works in CCM (Continuous Conduction Mode) under all
load conditions.
VIN and Power VIN Pins (VIN and PVIN)
The device allows for a variety of applications by using the VIN and PVIN pins together or separately. The VIN
pin voltage supplies the internal control circuits of the device. The PVIN pin voltage provides the input voltage to
the power converter system.
If tied together, the input voltage for VIN and PVIN can range from 4.5V to 17V. If using the VIN separately from
PVIN, the VIN pin must be between 4.5V and 17V, and the PVIN pin can range from as low as 1.6V to 17V. A
voltage divider connected to the EN pin can adjust the either input voltage UVLO appropriately. Adjusting the
input voltage UVLO on the PVIN pin helps to provide consistent power up behavior.
Voltage Reference
The voltage reference system produces a precise ±1% voltage reference over temperature by scaling the output
of a temperature stable bandgap circuit.
10
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
Adjusting the Output Voltage
The output voltage is set with a resistor divider from the output (VOUT) to the VSENSE pin. It is recommended to
use 1% tolerance or better divider resistors. Referring to the application schematic of Figure 29, start with a 10
kΩ for R6 and use Equation 1 to calculate R5. To improve efficiency at light loads consider using larger value
resistors. If the values are too high the regulator is more susceptible to noise and voltage errors from the
VSENSE input current are noticeable.
Vo - Vref
R5 =
R6
Vref
(1)
Where Vref = 0.6V
The minimum output voltage and maximum output voltage can be limited by the minimum on time of the
high-side MOSFET and bootstrap voltage (BOOT-PH voltage) respectively. More discussions are located in
Minimum Output Voltage and Bootstrap Voltage (BOOT) and Low Dropout Operation.
Safe Start-up into Pre-Biased Outputs
The device has been designed to prevent the low-side MOSFET from discharging a pre-biased output. During
monotonic pre-biased startup, the low-side MOSFET is not allowed to sink current until the SS/TR pin voltage is
higher than 1.4V.
Error Amplifier
The device uses a transconductance error amplifier. The error amplifier compares the VSENSE pin voltage to the
lower of the SS/TR pin voltage or the internal 0.6V voltage reference. The transconductance of the error amplifier
is 1300 μA/V during normal operation. The frequency compensation network is connected between the COMP
pin and ground.
Slope Compensation
The device adds a compensating ramp to the switch current signal. This slope compensation prevents
sub-harmonic oscillations. The available peak inductor current remains constant over the full duty cycle range.
Enable and Adjusting Under-Voltage Lockout
The EN pin provides electrical on/off control of the device. Once the EN pin voltage exceeds the threshold
voltage, the device starts operation. If the EN pin voltage is pulled below the threshold voltage, the regulator
stops switching and enters low Iq state.
The EN pin has an internal pull-up current source, allowing the user to float the EN pin for enabling the device. If
an application requires controlling the EN pin, use open drain or open collector output logic to interface with the
pin.
The device implements internal UVLO circuitry on the VIN pin. The device is disabled when the VIN pin voltage
falls below the internal VIN UVLO threshold. The internal VIN UVLO threshold has a hysteresis of 150mV.
If an application requires either a higher UVLO threshold on the VIN pin or a secondary UVLO on the PVIN, in
split rail applications, then the EN pin can be configured as shown in Figure 17, Figure 18 and Figure 19. When
using the external UVLO function it is recommended to set the hysteresis to be greater than 500mV.
The EN pin has a small pull-up current Ip which sets the default state of the pin to enable when no external
components are connected. The pull-up current is also used to control the voltage hysteresis for the UVLO
function since it increases by Ih once the EN pin crosses the enable threshold. The UVLO thresholds can be
calculated using Equation 2 and Equation 3.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
TPS54622
VIN
EN
ip
i
h
R 1
R 2
Figure 17. Adjustable VIN Under Voltage Lock Out
TPS54622
PVIN
ip
i
h
R 1
R 2
EN
Figure 18. Adjustable PVIN Under Voltage Lock Out, VIN ≥ 4.5V
TPS54622
VIN
ip
i
h
R 1
R 2
EN
Figure 19. Adjustable VIN and PVIN Under Voltage Lock Out
æ
ç
è
ö
÷
ø
VENFALLING
VSTART
- VSTOP
VENRISING
R1 =
æ
ç
è
ö
÷
ø
VENFALLING
Ip 1-
+I
h
VENRISING
R1´ VENFALLING
VSTOP - VENFALLING + R1(Ip + Ih )
(2)
(3)
R2 =
Where Ih = 3.4 μA, Ip = 1.15 μA, VENRISING = 1.21 V, VENFALLING = 1.17 V
Adjustable Switching Frequency and Synchronization (RT/CLK)
The RT/CLK pin can be used to set the switching frequency of the device in two modes.
12
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
In RT mode, a resistor (RT resistor) is connected between the RT/CLK pin and GND. The switching frequency of
the device is adjustable from 200 kHz to 1600 kHz by placing a maximum of 240 kΩ and minimum of 29 kΩ
respectively. In CLK mode, an external clock is connected directly to the RT/CLK pin. The device is synchronized
to the external clock frequency with PLL.
The CLK mode overrides the RT mode. The device is able to detect the proper mode automatically and switch
from the RT mode to CLK mode.
Adjustable Switching Frequency (RT Mode)
To determine the RT resistance for a given switching frequency, use Equation 4 or the curve in Figure 20. To
reduce the solution size one would set the switching frequency as high as possible, but tradeoffs of the supply
efficiency and minimum controllable on time should be considered.
-0.997
Rrt(kW) = 48000 ×Fsw kHz
(
- 2
)
(4)
250
200
150
100
50
0
200
400
600
800
1000
1200
1400
1600
Fsw − Oscillator Frequency − kHz
Figure 20. RT Set Resistor vs Switching Frequency
Synchronization (CLK mode)
An internal Phase Locked Loop (PLL) has been implemented to allow synchronization between 200kHz and
1600kHz, and to easily switch from RT mode to CLK mode.
To implement the synchronization feature, connect a square wave clock signal to the RT/CLK pin with a duty
cycle between 20% to 80%. The clock signal amplitude must transition lower than 0.8V and higher than 2.0V.
The start of the switching cycle is synchronized to the falling edge of RT/CLK pin.
In applications where both RT mode and CLK mode are needed, the device can be configured as shown in
Figure 21. Before the external clock is present, the device works in RT mode and the switching frequency is set
by RT resistor. When the external clock is present, the CLK mode overrides the RT mode. The first time the
SYNC pin is pulled above the RT/CLK high threshold (2.0V), the device switches from the RT mode to the CLK
mode and the RT/CLK pin becomes high impedance as the PLL starts to lock onto the frequency of the external
clock. It is not recommended to switch from the CLK mode back to the RT mode because the internal switching
frequency drops to 100kHz first before returning to the switching frequency set by RT resistor.
RT/CLK
mode select
TPS54622
RT/CLK
Rrt
Figure 21. Works with Both RT mode and CLK mode
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
Slow Start (SS/TR)
The device uses the lower voltage of the internal voltage reference or the SS/TR pin voltage as the reference
voltage and regulates the output accordingly. A capacitor on the SS/TR pin to ground implements a slow start
time. The device has an internal pull-up current source of 2.3μA that charges the external slow start capacitor.
The calculations for the slow start time (Tss, 10% to 90%) and slow start capacitor (Css) are shown in
Equation 5. The voltage reference (Vref) is 0.8 V and the slow start charge current (Iss) is 2.3μA.
Css(nF) ´ Vref(V)
Tss(ms) =
Iss(mA)
(5)
When the input UVLO is triggered, the EN pin is pulled below 1.21V, or a thermal shutdown event occurs the
device stops switching and enters low current operation. At the subsequent power up, when the shutdown
condition is removed, the device does not start switching until it has discharged its SS/TR pin to ground ensuring
proper soft start behavior.
Power Good (PWRGD)
The PWRGD pin is an open drain output. Once the VSENSE pin is between 94% and 104% of the internal
voltage reference the PWRGD pin pull-down is de-asserted and the pin floats. It is recommended to use a
pull-up resistor between the values of 10kΩ and 100kΩ to a voltage source that is 5.5V or less. The PWRGD is
in a defined state once the VIN input voltage is greater than 1V but with reduced current sinking capability. The
PWRGD achieves full current sinking capability once the VIN input voltage is above 4.5V.
The PWRGD pin is pulled low when VSENSE is lower than 92% or greater than 106% of the nominal internal
reference voltage. Also, the PWRGD is pulled low, if the input UVLO or thermal shutdown are asserted, the EN
pin is pulled low or the SS/TR pin is below 1.4V.
Bootstrap Voltage (BOOT) and Low Dropout Operation
The device has an integrated boot regulator, and requires a small ceramic capacitor between the BOOT and PH
pins to provide the gate drive voltage for the high-side MOSFET. The boot capacitor is charged when the BOOT
pin voltage is less than VIN and BOOT-PH voltage is below regulation. The value of this ceramic capacitor
should be 0.1μF. A ceramic capacitor with an X7R or X5R grade dielectric with a voltage rating of 10V or higher
is recommended because of the stable characteristics over temperature and voltage.
To improve drop out, the device is designed to operate at 100% duty cycle as long as the BOOT to PH pin
voltage is greater than the BOOT-PH UVLO threshold which is typically 2.1V. When the voltage between BOOT
and PH drops below the BOOT-PH UVLO threshold the high-side MOSFET is turned off and the low-side
MOSFET is turned on allowing the boot capacitor to be recharged. In applications with split input voltage rails
100% duty cycle operation can be achieved as long as (VIN – PVIN) > 4V.
Sequencing (SS/TR)
Many of the common power supply sequencing methods can be implemented using the SS/TR, EN and PWRGD
pins.
The sequential method is illustrated in Figure 22 using two TPS54622 devices. The power good of the first
device is coupled to the EN pin of the second device which enables the second power supply once the primary
supply reaches regulation.
TPS54622
TPS54622
PWRGD
EN
EN
SS/TR
SS/TR
PWRGD
Figure 22. Sequential Start Up Sequence
14
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
Figure 23 shows the method implementing ratio-metric sequencing by connecting the SS/TR pins of two devices
together. The regulator outputs ramp up and reach regulation at the same time. When calculating the slow start
time the pull-up current source must be doubled in Equation 5.
TPS54622
EN
SS/TR
PWRGD
TPS54622
EN
SS/TR
PWRGD
Figure 23. Ratiometric Start Up Sequence
Ratio-metric and simultaneous power supply sequencing can be implemented by connecting the resistor network
of R1 and R2 shown in Figure 24 to the output of the power supply that needs to be tracked or another voltage
reference source. Using Equation 6 and Equation 7, the tracking resistors can be calculated to initiate the Vout2
slightly before, after or at the same time as Vout1. Equation 8 is the voltage difference between Vout1 and
Vout2.
To design a ratio-metric start up in which the Vout2 voltage is slightly greater than the Vout1 voltage when Vout2
reaches regulation, use a negative number in Equation 6 and Equation 7 for deltaV. Equation 8 results in a
positive number for applications where the Vout2 is slightly lower than Vout1 when Vout2 regulation is
achieved. .
The deltaV variable is zero volt for simultaneous sequencing. To minimize the effect of the inherent SS/TR to
VSENSE offset (Vssoffset, 29mV) in the slow start circuit and the offset created by the pull-up current source
(Iss, 2.3μA) and tracking resistors, the Vssoffset and Iss are included as variables in the equations.
To ensure proper operation of the device, the calculated R1 value from Equation 6 must be greater than the
value calculated in Equation 9.
Vout2 + DV
Vssoffset
R1 =
´
Vref
Iss
(6)
Vref ´ R1
Vout2 + DV - Vref
R2 =
(7)
(8)
(9)
DV = Vout1 - Vout2
R1> 2800´ Vout1-180´DV
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
TPS54622
EN
VOUT1
SS/TR
PWRGD
TPS54622
VOUT2
EN
R1
R2
SS/TR
PWRGD
R3
R4
Figure 24. Ratiometric and Simultaneous Startup Sequence
Output Overvoltage Protection (OVP)
The device incorporates an output overvoltage protection (OVP) circuit to minimize output voltage overshoot. For
example, when the power supply output is overloaded the error amplifier compares the actual output voltage to
the internal reference voltage. If the VSENSE pin voltage is lower than the internal reference voltage for a
considerable time, the output of the error amplifier demands maximum output current. Once the condition is
removed, the regulator output rises and the error amplifier output transitions to the steady state voltage. In some
applications with small output capacitance, the power supply output voltage can respond faster than the error
amplifier. This leads to the possibility of an output overshoot. The OVP feature minimizes the overshoot by
comparing the VSENSE pin voltage to the OVP threshold. If the VSENSE pin voltage is greater than the OVP
threshold the high-side MOSFET is turned off preventing current from flowing to the output and minimizing output
overshoot. When the VSENSE voltage drops lower than the OVP threshold, the high-side MOSFET is allowed to
turn on at the next clock cycle.
Overcurrent Protection
The device is protected from overcurrent conditions by cycle-by-cycle current limiting on both the high-side
MOSFET and the low-side MOSFET.
High-side MOSFET overcurrent protection
The device implements current mode control which uses the COMP pin voltage to control the turn off of the
high-side MOSFET and the turn on of the low-side MOSFET on a cycle by cycle basis. Each cycle the switch
current and the current reference generated by the COMP pin voltage are compared, when the peak switch
current intersects the current reference the high-side switch is turned off.
Low-side MOSFET overcurrent protection
While the low-side MOSFET is turned on its conduction current is monitored by the internal circuitry. During
normal operation the low-side MOSFET sources current to the load. At the end of every clock cycle, the low-side
MOSFET sourcing current is compared to the internally set low-side sourcing current limit. If the low-side
sourcing current is exceeded the high-side MOSFET is not turned on and the low-side MOSFET stays on for the
next cycle. The high-side MOSFET is turned on again when the low-side current is below the low-side sourcing
current limit at the start of a cycle.
The low-side MOSFET may also sink current from the load. If the low-side sinking current limit is exceeded the
low-side MOSFET is turned off immediately for the rest of that clock cycle. In this scenario both MOSFETs are
off until the start of the next cycle.
16
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
Furthermore, if an output overload condition (as measured by the COMP pin voltage) has lasted for more than
the hiccup wait time which is programmed for 512 switching cycles, the device will shut down itself and restart
after the hiccup time of 16384 cycles. The hiccup mode helps to reduce the device power dissipation under
severe overcurrent conditions.
Thermal Shutdown
The internal thermal shutdown circuitry forces the device to stop switching if the junction temperature exceeds
175°C typically. Once the junction temperature drops below 165°C typically, the internal thermal hiccup timer will
start to count. The device reinitiates the power up sequence after the built-in thermal shutdown hiccup time
(16384 cycles) is over.
Small Signal Model for Loop Response
Figure 25 shows an equivalent model for the device control loop which can be modeled in a circuit simulation
program to check frequency response and transient responses. The error amplifier is a transconductance
amplifier with a gm of 1300μA/V. The error amplifier can be modeled using an ideal voltage controlled current
source. The resistor Roea (2.38 MΩ) and capacitor Coea (20.7 pF) model the open loop gain and frequency
response of the error amplifier. The 1-mV ac voltage source between the nodes a and b effectively breaks the
control loop for the frequency response measurements. Plotting a/c and c/b show the small signal responses of
the power stage and frequency compensation respectively. Plotting a/b shows the small signal response of the
overall loop. The dynamic loop response can be checked by replacing the RL with a current source with the
appropriate load step amplitude and step rate in a time domain analysis.
PH
VOUT
Power Stage
16 A/V
a
b
RESR
R1
RL
COMP
c
C
O
VSENSE
R2
0.6V
Coea
Roea
R3
C1
gm
1300 mA/V
C2
Figure 25. Small Signal Model for Loop Response
Simple Small Signal Model for Peak Current Mode Control
Figure 26 is a simple small signal model that can be used to understand how to design the frequency
compensation. The device power stage can be approximated to a voltage controlled current source (duty cycle
modulator) supplying current to the output capacitor and load resistor. The control to output transfer function is
shown in Equation 10 and consists of a dc gain, one dominant pole and one ESR zero. The quotient of the
change in switch current and the change in COMP pin voltage (node c in Figure 25) is the power stage
transconductance (gmps) which is 16 A/V for the device. The DC gain of the power stage is the product of gmps
and the load resistance ®L) as shown in Equation 11 with resistive loads. As the load current increases, the DC
gain decreases. This variation with load may seem problematic at first glance, but fortunately the dominant pole
moves with load current (see Equation 12). The combined effect is highlighted by the dashed line in Figure 27.
As the load current decreases, the gain increases and the pole frequency lowers, keeping the 0-dB crossover
frequency the same for the varying load conditions which makes it easier to design the frequency compensation.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
VOUT
VC
RESR
RL
gm
ps
CO
Figure 26. Simplified Small Signal Model for Peak Current Mode Control
VOUT
Adc
VC
RESR
fp
RL
gm
ps
CO
fz
Figure 27. Simplified Frequency Response for Peak Current Mode Control
æ
ç
è
s
ö
÷
ø
1+
2p ´ ¦z
VOUT
VC
= Adc ´
æ
ö
÷
ø
s
1+
ç
è
2p ´ ¦p
(10)
(11)
Adc = gmps ´ RL
1
¦p =
C
´ R ´ 2p
O
L
(12)
(13)
1
¦z =
C
´ R
´ 2p
ESR
O
Where
gmea is the GM amplifier gain ( 1300μA/V)
gmps is the power stage gain (16A/V).
RL is the load resistance
CO is the output capacitance.
RESR is the equivalent series resistance of the output capacitor.
Small Signal Model for Frequency Compensation
The device uses a transconductance amplifier for the error amplifier and readily supports two of the commonly
used Type II compensation circuits and a Type III frequency compensation circuit, as shown in Figure 28. In
Type 2A, one additional high frequency pole, C6, is added to attenuate high frequency noise. In Type III, one
additional capacitor, C11, is added to provide a phase boost at the crossover frequency. See Designing Type III
Compensation for Current Mode Step-Down Converters (SLVA352) for a complete explanation of Type III
compensation.
18
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
The design guidelines below are provided for advanced users who prefer to compensate using the general
method. The below equations only apply to designs whose ESR zero is above the bandwidth of the control loop.
This is usually true with ceramic output capacitors. See the Application Information section for a step-by-step
design procedure using higher ESR output capacitors with lower ESR zero frequencies.
VOUT
C11
R8
VSENSE
Type 2A
Type 2B
COMP
Coea
Type 3
Vref
R4
C4
gm
C6
R4
C4
ea
Roea
R9
Figure 28. Types of Frequency Compensation
The general design guidelines for device loop compensation are as follows:
1. Determine the crossover frequency, fc. A good starting point is 1/10th of the switching frequency, fsw.
2. R4 can be determined by:
2p ´ ¦c ´ VOUT ´ Co
R4 =
gmea ´ Vref ´ gmps
(14)
Where:
gmea is the GM amplifier gain (1300μA/V)
gmps is the power stage gain (16A/V)
Vref is the reference voltage (0.6V)
æ
ç
è
ö
÷
ø
1
¦p =
CO ´ RL ´ 2p
3. Place a compensation zero at the dominant pole:
C4 can be determined by:
RL ´ Co
C4 =
R4
(15)
4. C6 is optional. It can be used to cancel the zero from the ESR (Equivalent Series Resistance) of the output
capacitor Co.
RESR ´ Co
C6 =
R4
(16)
5. Type III compensation can be implemented with the addition of one capacitor, C11. This allows for slightly
higher loop bandwidths and higher phase margins. If used, C11 is calculated from Equation 17.
1
C11=
2×p ×R8×fc
(
)
(17)
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
APPLICATION INFORMATION
Design Guide – Step-By-Step Design Procedure
This example details the design of a high frequency switching regulator design using ceramic output capacitors.
A few parameters must be known in order to start the design process. These parameters are typically determined
at the system level. For this example, we start with the following known parameters:
Table 1.
Parameter
Output Voltage
Value
3.3 V
Output Current
6 A
Transient Response 1A load step
Input Voltage
ΔVout = 5 %
12 V nominal, 8 V to 17 V
33 mV p-p
6.528 V
Output Voltage Ripple
Start Input Voltage (Rising Vin)
Stop Input Voltage (Falling Vin)
Switching Frequency
6.190 V
480 kHz
Typical Application Schematic
The application schematic of Figure 29 was developed to meet the requirements above. This circuit is available
as the TPS54622EVM-012 evaluation module. The design procedure is given in this section. For more
information about Type II and Type III frequency compensation circuits, see Designing Type III Compensation for
Current Mode Step-Down Converters (SLVA352) and Design Calculator (SLVC219).
U1
R3
TPS54622RHL
100k
C3
0.1uF
1
2
3
4
5
6
7
14
13
12
11
10
9
L1
RT/CLK
GND
PWRGD
BOOT
PH
3.3uH
VOUT = 3.3 V, 6 A
VOUT
VIN = 8 - 17 V
GND
VIN
PVIN
PVIN
VIN
PH
R5
C7
C8
EN
10.0k
100uF
Optional
EN
C1
10uF
V_SNS
SS/TR
COMP
V_SNS
8
V_SNS
R1
R6
35.7k
R4
2.21k
C2
3.74k
EN
15
C5
47pF
C6
4.7uF
0.022uf
R2
C4
8.06k
0.01uf
Figure 29. Typical Application Circuit
Operating Frequency
The first step is to decide on a switching frequency for the regulator. There is a trade off between higher and
lower switching frequencies. Higher switching frequencies may produce smaller a solution size using lower
valued inductors and smaller output capacitors compared to a power supply that switches at a lower frequency.
However, the higher switching frequency causes extra switching losses, which hurt the converter’s efficiency and
thermal performance. In this design, a moderate switching frequency of 480 kHz is selected to achieve both a
small solution size and a high efficiency operation.
20
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
Output Inductor Selection
To calculate the value of the output inductor, use Equation 18. KIND is a coefficient that represents the amount
of inductor ripple current relative to the maximum output current. The inductor ripple current is filtered by the
output capacitor. Therefore, choosing high inductor ripple currents impact the selection of the output capacitor
since the output capacitor must have a ripple current rating equal to or greater than the inductor ripple current. In
general, the inductor ripple value is at the discretion of the designer; however, KIND is normally from 0.1 to 0.3
for the majority of applications.
Vinmax - Vout
Vout
L1 =
×
Io ×Kind
Vinmax × f sw
(18)
For this design example, use KIND = 0.3 and the inductor value is calculated to be 3.08 µH. For this design, a
nearest standard value was chosen: 3.3 µH. For the output filter inductor, it is important that the RMS current
and saturation current ratings not be exceeded. The RMS and peak inductor current can be found from
Equation 20 and Equation 21.
Vinmax - Vout
Vout
Iripple =
×
L1
Vinmax × f sw
(19)
2
æ
ö
V × Vinmax - Vo
(
o
)
1
ILrms = Io2 +
ILpeak = Iout +
×
ç
÷
ç
÷
12
Vinmax×L1× f sw
è
ø
(20)
(21)
Iripple
2
For this design, the RMS inductor current is 6.02 A and the peak inductor current is 6.84 A. The chosen inductor
is a Coilcraft MSS1048 series 3.3 µH. It has a saturation current rating of 7.38 A and a RMS current rating of
7.22 A.
The current flowing through the inductor is the inductor ripple current plus the output current. During power up,
faults or transient load conditions, the inductor current can increase above the calculated peak inductor current
level calculated above. In transient conditions, the inductor current can increase up to the switch current limit of
the device. For this reason, the most conservative approach is to specify an inductor with a saturation current
rating equal to or greater than the switch current limit rather than the peak inductor current.
Output Capacitor Selection
There are three primary considerations for selecting the value of the output capacitor. The output capacitor
determines the modulator pole, the output voltage ripple, and how the regulator responds to a large change in
load current. The output capacitance needs to be selected based on the more stringent of these three criteria
The desired response to a large change in the load current is the first criteria. The output capacitor needs to
supply the load with current when the regulator can not. This situation would occur if there are desired hold-up
times for the regulator where the output capacitor must hold the output voltage above a certain level for a
specified amount of time after the input power is removed. The regulator is also temporarily not able to supply
sufficient output current if there is a large, fast increase in the current needs of the load such as a transition from
no load to full load. The regulator usually needs two or more clock cycles for the control loop to see the change
in load current and output voltage and adjust the duty cycle to react to the change. The output capacitor must be
sized to supply the extra current to the load until the control loop responds to the load change. The output
capacitance must be large enough to supply the difference in current for 2 clock cycles while only allowing a
tolerable amount of droop in the output voltage. Equation 22 shows the minimum output capacitance necessary
to accomplish this.
2×DIout
Co >
f sw ×DVout
(22)
Where ΔIout is the change in output current, Fsw is the regulators switching frequency and ΔVout is the
allowable change in the output voltage. For this example, the transient load response is specified as a 5%
change in Vout for a load step of 1A. For this example, ΔIout = 3.0 A and ΔVout = 0.05 x 3.3 = 0.165 V. Using
these numbers gives a minimum capacitance of 75.8 μF. This value does not take the ESR of the output
capacitor into account in the output voltage change. For ceramic capacitors, the ESR is usually small enough to
ignore in this calculation.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
Equation 23 calculates the minimum output capacitance needed to meet the output voltage ripple specification.
Where fsw is the switching frequency, Vripple is the maximum allowable output voltage ripple, and Iripple is the
inductor ripple current. In this case, the maximum output voltage ripple is 33mV. Under this requirement,
Equation 23 yields 13.2µF.
1
1
Co >
×
Voripple
Iripple
8× f sw
(23)
Equation 24 calculates the maximum ESR an output capacitor can have to meet the output voltage ripple
specification. Equation 24 indicates the ESR should be less than 19.7 mΩ. In this case, the ceramic caps’ ESR is
much smaller than 19.7 mΩ.
Voripple
Resr <
Iripple
(24)
Additional capacitance de-ratings for aging, temperature and DC bias should be factored in which increases this
minimum value. For this example, a 100 μF 6.3V X5R ceramic capacitor with 3 mΩ of ESR is be used.
Capacitors generally have limits to the amount of ripple current they can handle without failing or producing
excess heat. An output capacitor that can support the inductor ripple current must be specified. Some capacitor
data sheets specify the RMS (Root Mean Square) value of the maximum ripple current. Equation 25 can be used
to calculate the RMS ripple current the output capacitor needs to support. For this application, Equation 25 yields
485mA.
Vout × Vinmax - Vout
(
)
Icorms =
12 ×Vinmax×L1× f sw
(25)
Input Capacitor Selection
The TPS54622 requires a high quality ceramic, type X5R or X7R, input decoupling capacitor of at least 4.7 µF of
effective capacitance on the PVIN input voltage pins and 4.7 µF on the Vin input voltage pin. In some
applications additional bulk capacitance may also be required for the PVIN input. The effective capacitance
includes any DC bias effects. The voltage rating of the input capacitor must be greater than the maximum input
voltage. The capacitor must also have a ripple current rating greater than the maximum input current ripple of the
TPS54622. The input ripple current can be calculated using Equation 26.
Vinmin - Vout
(
)
Vout
Icirms = Iout ×
×
Vinmin
Vinmin
(26)
The value of a ceramic capacitor varies significantly over temperature and the amount of DC bias applied to the
capacitor. The capacitance variations due to temperature can be minimized by selecting a dielectric material that
is stable over temperature. X5R and X7R ceramic dielectrics are usually selected for power regulator capacitors
because they have a high capacitance to volume ratio and are fairly stable over temperature. The output
capacitor must also be selected with the DC bias taken into account. The capacitance value of a capacitor
decreases as the DC bias across a capacitor increases. For this example design, a ceramic capacitor with at
least a 25 V voltage rating is required to support the maximum input voltage. For this example, one 10 μF and
one 4.7 µF 25 V capacitors in parallel have been selected as the VIN and PVIN inputs are tied together so the
TPS54622 may operate from a single supply. The input capacitance value determines the input ripple voltage of
the regulator. The input voltage ripple can be calculated using Equation 27. Using the design example values,
Ioutmax = 6 A, Cin = 14.7 μF, Fsw=480 kHz, yields an input voltage ripple of 213 mV and a RMS input ripple
current of 2.95 A.
Ioutmax ×0.25
DVin =
Cin× f sw
(27)
Slow Start Capacitor Selection
The slow start capacitor determines the minimum amount of time it takes for the output voltage to reach its
nominal programmed value during power up. This is useful if a load requires a controlled voltage slew rate. This
is also used if the output capacitance is very large and would require large amounts of current to quickly charge
the capacitor to the output voltage level. The large currents necessary to charge the capacitor may make the
TPS54622 reach the current limit or excessive current draw from the input power supply may cause the input
22
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
voltage rail to sag. Limiting the output voltage slew rate solves both of these problems. The soft start capacitor
value can be calculated using Equation 28. For the example circuit, the soft start time is not too critical since the
output capacitor value is 100 μF which does not require much current to charge to 3.3 V. The example circuit has
the soft start time set to an arbitrary value of 6 ms which requires a 22 nF capacitor. In TPS54622, Iss is 2.3 uA
and Vref is 0.6V.
Tss(ms)×Iss(mA)
C6(nF) =
Vref(V)
(28)
Bootstrap Capacitor Selection
A 0.1 µF ceramic capacitor must be connected between the BOOT to PH pin for proper operation. It is
recommended to use a ceramic capacitor with X5R or better grade dielectric. The capacitor should have 10V or
higher voltage rating.
Under Voltage Lockout Set Point
The Under Voltage Lock Out (UVLO) can be adjusted using the external voltage divider network of R3 and R4.
R3 is connected between VIN and the EN pin of the TPS54622 and R4 is connected between EN and GND .
The UVLO has two thresholds, one for power up when the input voltage is rising and one for power down or
brown outs when the input voltage is falling. For the example design, the supply should turn on and start
switching once the input voltage increases above 6.528V (UVLO start or enable). After the regulator starts
switching, it should continue to do so until the input voltage falls below 6.190 V (UVLO stop or disable).
Equation 2 and Equation 3 can be used to calculate the values for the upper and lower resistor values. For the
stop voltages specified the nearest standard resistor value for R3 is 35.7 kΩ and for R4 is 8.06 kΩ.
Output Voltage Feedback Resistor Selection
The resistor divider network R5 and R6 is used to set the output voltage. For the example design, 10 kΩ was
selected for R5. Using Equation 29, R6 is calculated as 2.22 kΩ. The nearest standard 1% resistor is 2.21 kΩ.
R5×Vref
R6 =
Vo - Vref
(29)
Minimum Output Voltage
Due to the internal design of the TPS54622, there is a minimum output voltage limit for any given input voltage.
The output voltage can never be lower than the internal voltage reference of 0.8 V. Above 0.8 V, the output
voltage may be limited by the minimum controllable on time. The minimum output voltage in this case is given by
Equation 30
Voutmin = Ontimemin×Fsmax Vinmax +Ioutmin RDS2min -RDS1min -Ioutmin RL +RDS2min
( ) (
)
)
(
Where:
Voutmin = minimum achievable output voltage
Ontimemin = minimum controllable on-time (135 nsec maximum)
Fsmax = maximum switching frequency including tolerance
Vinmax = maximum input voltage
Ioutmin = minimum load current
RDS1min = minimum high side MOSFET on resistance (36-32 mΩ typical)
RDS2min = minimum low side MOSFET on resistance (19 mΩ typical)
RL = series resistance of output inductor
(30)
Compensation Component Selection
There are several industry techniques used to compensate DC/DC regulators. The method presented here is
easy to calculate and yields high phase margins. For most conditions, the regulator has a phase margin between
60 and 90 degrees. The method presented here ignores the effects of the slope compensation that is internal to
the TPS54622. Since the slope compensation is ignored, the actual cross over frequency is usually lower than
the cross over frequency used in the calculations. Use SwitcherPro software for a more accurate design.
First, the modulator pole, fpmod, and the esr zero, fzmod must be calculated using Equation 31 and Equation 32.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
23
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
For Cout, use a derated value of 75 µF. use Equation 33 and Equation 34 to estimate a starting point for the
closed loop crossover frequency fco. Then the required compensation components may be derived. For this
design example, fpmod is 3.86 kHz and fzmod is 707.4 kHz. Equation 33 is the geometric mean of the modulator
pole and the esr zero and Equation 34 is the geometric mean of the modulator pole and one half the switching
frequency. Use a frequency near the lower of these two values as the intended crossover frequency fco. In this
case Equation 33 yields 52.2 kHz and Equation 34 yields 30.4 kHz. The lower value is 30.4 kHz. A slightly higher
frequency of 30 kHz is chosen as the intended crossover frequency.
Iout
f pmod =
2×p ×Vout ×Cout
1
(31)
f zmod =
2 ×p ×RESR ×Cout
(32)
(33)
f co = f pmod× f zmod
f sw
f co = f pmod×
2
(34)
Now the compensation components can be calculated. First calculate the value for R2 which sets the gain of the
compensated network at the crossover frequency. Use Equation 35 to determine the value of R2.
2p × f c × Vout×Cout
R4 =
gmea ×Vref ×gmps
(35)
Next calculate the value of C3. Together with R2, C3 places a compensation zero at the modulator pole
frequency. Equation 36 to determine the value of C3.
Vout ×Cout
C4 =
Iout ×R4
(36)
Using Equation 35 and Equation 36 the standard values for R4 and C4 are 3.74 kΩ and 0.01 µF.
An additional high frequency pole can be used if necessary by adding a capacitor in parallel with the series
combination of R4 and C4. The pole frequency can be placed at the ESR zero frequency of the output cpacitor
as given by Equation 13. Use Equation 37 to calculate the required capacitor value for C5.
RESR×Cout
C5 =
R4
(37)
Application Curves
LOAD TRANSIENT
STARTUP with VIN
VOUT = 100 mV / div (dc coupled, -3.13 V offset)
VIN = 5 V / div
IOUT = 2 A / div
VOUT = 1 V / div
Load step = 1.5 A to 4.5 A Slew rate = 100 mA / µsec
Time = 2 msec / div
Time = 200 µsec / div
Figure 30.
Figure 31.
24
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
STARTUP with EN
STARTUP with PRE-BIAS
VIN = 5 V / div
VIN = 10 V / div
VOUT = 2 V / div
EN = 2 V / div
VOUT = 2 V / div
PH = 10 V / div
Time = 2 msec / div
Time = 2 msec / div
Figure 32.
Figure 33.
OUTPUT VOLTAGE RIPPLE with FULL LOAD
INPUT VOLTAGE RIPPLE with FULL LOAD
VOUT = 20 mV / div (ac coupled)
VIN = 500 mV / div
PH = 5 V / div
PH = 5 V / div
Time = 1 µsec / div
Time = 1 µsec / div
Figure 34.
Figure 35.
CLOSED LOOP RESPONSE
LINE REGULATION
60
180
150
0.4
50
40
Phase
0.3
0.2
0.1
0
120
30
90
60
30
0
IOUT = 3 A
20
10
0
Gain
-10
-20
-30
-40
-50
-60
-30
-0.1
-0.2
-0.3
-0.4
-60
-90
-120
-150
-180
100
1000
10000
100000
1000000
Frequency - Hz
8
9
10
11
12
13
14
15
16
17
Input Voltage - V
Figure 36.
Figure 37.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
25
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
LOAD REGULATION
TRACKING PERFORMANCE
0.4
0.3
0.2
0.1
0
10
1
10
Vout
1
VIN = 12 V
0.1
0.1
0.01
Ideal Vsense
Vsense
0.01
-0.1
-0.2
-0.3
-0.4
0.001
0.0001
0.00001
0.001
0.0001
0.00001
0
1
2
3
4
5
6
0.001
0.01
0.1
1
10
Output Current - A
Track In Voltage - V
Figure 38.
Figure 39.
MAXIMUM AMBIENT TEMPERATURE
MAXIMUM AMBIENT TEMPERATURE
vs
vs
LOAD CURRENT
IC POWER DISSIPATION
150
150
Tjmax = 150 °C,
no air flow
125
100
125
100
75
75
50
25
V
V
= 12 V,
IN
= 3.3 V,
50
25
OUT
Fsw = 480 kHz,
room temp, no air flow
0
0.5
1
1.5
2
2.5
3
- IC Power Dissipation - W
3.5
4
0
1
2
3
4
Load Current - A
5
6
P
D
Figure 40.
Figure 41.
JUNCTION TEMPERATURE
vs
EFFICIENCY
vs
IC POWER DISSIPATION
LOAD CURRENT
100
95
90
85
80
75
70
65
60
55
150
125
100
T
= room temperature,
A
no air flow
VIN = 8 V
VIN = 12 V
VIN = 17 V
75
50
25
50
0
1
2
3
4
5
6
0
0.5
1
1.5
2
2.5
3
Pic - IC Power Dissipation - W
3.5
4
Output Current - A
Figure 42.
Figure 43.
26
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
EFFICIENCY
vs
OUTPUT CURRENT
TPS54622 Hiccup Mode Current Limit
100
90
80
70
60
50
40
30
20
10
0
VIN = 12 V
VIN = 17 V
VIN = 8 V
VOUT = 2 V / div
PH = 10 V / div
Inductor Current = 5 A / div
Time = 20 msec / div
10.0
0.01
0.1
1.0
Output Current - A
Figure 44.
Figure 45.
Fast Transient Considerations
In applications where fast transient responses are very important, Type III frequency compensation can be used
instead of the traditional Type II frequency compensation.
For more information about Type II and Type III frequency compensation circuits, see Designing Type III
Compensation for Current Mode Step-Down Converters (SLVA352) and Design Calculator (SLVC219).
PCB Layout Guidelines
Layout is a critical portion of good power supply design. See Figure 46 for a PCB layout example. The top layer
contains the main power traces for VIN, VOUT, and VPHASE. Also on the top layer are connections for the
remaining pins of the TPS54622 and a large top side area filled with ground. The top layer ground area should
be connected to the internal ground layer(s) using vias at the input bypass capacitor, the output filter capacitor
and directly under the TPS54622 device to provide a thermal path from the exposed thermal pad land to ground.
The GND pin should be tied directly to the power pad under the IC and the power pad. For operation at full rated
load, the top side ground area together with the internal ground plane, must provide adequate heat dissipating
area. There are several signals paths that conduct fast changing currents or voltages that can interact with stray
inductance or parasitic capacitance to generate noise or degrade the power supplies performance. To help
eliminate these problems, the PVIN pin should be bypassed to ground with a low ESR ceramic bypass capacitor
with X5R or X7R dielectric. Care should be taken to minimize the loop area formed by the bypass capacitor
connections, the PVIN pins, and the ground connections. The VIN pin must also be bypassed to ground using a
low ESR ceramic capacitor with X5R or X7R dielectric. Make sure to connect this capacitor to the quite analog
ground trace rather than the power ground trace of the PVIn bypass capacitor. Since the PH connection is the
switching node, the output inductor should be located close to the PH pins, and the area of the PCB conductor
minimized to prevent excessive capacitive coupling. The output filter capacitor ground should use the same
power ground trace as the PVIN input bypass capacitor. Try to minimize this conductor length while maintaining
adequate width. The small signal components should be grounded to the analog ground path as shown. The
RT/CLK pin is sensitive to noise so the RT resistor should be located as close as possible to the IC and routed
with minimal lengths of trace. The additional external components can be placed approximately as shown. It may
be possible to obtain acceptable performance with alternate PCB layouts, however this layout has been shown to
produce good results and is meant as a guideline.
Land pattern and stencil information is provided in the data sheet addendum. The dimension and outline
information is for the standard RHL (S-PVQFN-N14) package. There may be slight differences between the
provided data and actual lead frame used on the TPS54622RHL package.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
27
Product Folder Link(s) :TPS54622
TPS54622
SLVSA70 –MARCH 2011
www.ti.com
TOPSIDE
GROUND
AREA
FREQUENCY SET RESISTOR
OUTPUT
FILTER
CAPACITOR
PVIN
INPUT
BYPASS
CAPACITOR
RT/CLK
PWRGD
BOOT
CAPACITOR
GND
GND
PVIN
PVIN
VIN
BOOT
PH
OUTPUT
INDUCTOR
EXPOSED THERMAL
PAD AREA
PH
VOUT
PH
EN
SS/TR
COMP
VSENSE
PVIN
VIN
SLOW START
CAPACITOR
UVLO SET
RESISTORS
VIN
INPUT
BYPASS
CAPACITOR
COMPENSATION
NETWORK
FEEDBACK
RESISTORS
ANALOG GROUND TRACE
0.010 in. Diameter
Thermal VIA to Ground Plane
VIA to Ground Plane
Etch Under Component
Figure 46. PCB Layout
28
Submit Documentation Feedback
Copyright © 2011, Texas Instruments Incorporated
Product Folder Link(s) :TPS54622
TPS54622
www.ti.com
SLVSA70 –MARCH 2011
Figure 47. Ultra-Small PCB Layout Using TPS54622 (PMP4854-2)
Estimated Circuit Area
The estimated printed circuit board area for the components used in the design of Figure 29 is 0.58 in2
(374mm2). This area does not include test points or connectors.
Copyright © 2011, Texas Instruments Incorporated
Submit Documentation Feedback
29
Product Folder Link(s) :TPS54622
PACKAGE OPTION ADDENDUM
www.ti.com
4-Apr-2011
PACKAGING INFORMATION
Status (1)
Eco Plan (2)
MSL Peak Temp (3)
Samples
Orderable Device
Package Type Package
Drawing
Pins
Package Qty
Lead/
Ball Finish
(Requires Login)
TPS54622RHLR
TPS54622RHLT
ACTIVE
ACTIVE
QFN
QFN
RHL
RHL
14
14
3000
250
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
Green (RoHS
& no Sb/Br)
CU NIPDAU Level-2-260C-1 YEAR
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Apr-2011
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS54622RHLR
TPS54622RHLT
QFN
QFN
RHL
RHL
14
14
3000
250
330.0
180.0
12.4
12.4
3.85
3.85
3.85
3.85
1.35
1.35
8.0
8.0
12.0
12.0
Q2
Q2
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
6-Apr-2011
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS54622RHLR
TPS54622RHLT
QFN
QFN
RHL
RHL
14
14
3000
250
346.0
190.5
346.0
212.7
29.0
31.8
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
Medical
Security
Logic
Space, Avionics and Defense www.ti.com/space-avionics-defense
Power Mgmt
power.ti.com
Transportation and
Automotive
www.ti.com/automotive
Microcontrollers
RFID
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
Wireless
www.ti.com/video
www.ti.com/wireless-apps
RF/IF and ZigBee® Solutions www.ti.com/lprf
TI E2E Community Home Page
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2011, Texas Instruments Incorporated
相关型号:
TPS54622_17
4.5-V to 17-V Input, 6-A Synchronous Step-Down SWIFT Converter With Hiccup Protection
TI
TPS54623
4.5V to 17V Input, 6A Synchronous Step Down SWIFT⢠Converter With Light Load Efficiency and Hiccup Over Current Protection
TI
TPS54623RHLR
4.5V to 17V Input, 6A Synchronous Step Down SWIFT⢠Converter With Light Load Efficiency and Hiccup Over Current Protection
TI
TPS54623RHLT
4.5V to 17V Input, 6A Synchronous Step Down SWIFT⢠Converter With Light Load Efficiency and Hiccup Over Current Protection
TI
©2020 ICPDF网 联系我们和版权申明