TPS563210A [TI]
采用 SOT-23 封装且具有高级 Eco-mode™、PG 和软启动功能的 17V 输入、3A 同步降压稳压器;型号: | TPS563210A |
厂家: | TEXAS INSTRUMENTS |
描述: | 采用 SOT-23 封装且具有高级 Eco-mode™、PG 和软启动功能的 17V 输入、3A 同步降压稳压器 软启动 稳压器 |
文件: | 总29页 (文件大小:1241K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
TPS56x210A 采用 8 引脚 SOT-23 封装的
4.5V 至 17V 输入、2A/3A 同步降压稳压器
1 特性
3 说明
1
•
TPS562210A:集成有
133mΩ 和 80mΩ 场效应晶体管 (FET) 的 2A 转换
器
TPS562210A 和 TPS563210A 是采用 8 引脚 SOT-23
封装的简单易用型 2A/3A 同步降压转换器。
两款器件均经过优化,最大限度地减少了运行所需的外
部组件并且可以实现低待机电流。
•
TPS563210A:集成有
68mΩ 和 39mΩ FET 的 3A 转换器
•
•
•
•
•
•
•
•
•
•
•
D-CAP2™针对快速瞬态响应的模式控制
高级 Eco-mode™脉冲跳跃
输入电压范围:4.5V 至 17V
输出电压范围:0.76V 至 7V
650kHz 开关频率
这些开关模式电源 (SMPS) 器件采用 D-CAP2™ 模式
控制,从而提供快速瞬态响应,并且在无需外部补偿组
件的情况下支持诸如高分子聚合物等低等效串联电阻
(ESR) 输出电容器以及超低 ESR 陶瓷电容器。
该器件可在高级 Eco-mode™ 下运行,从而能在轻载
运行期间保持高效率。TPS562210A 和 TPS563210A
采用 8 引脚 1.6mm × 2.9mm SOT (DDF) 封装,额定
环境温度范围为 –40°C 至 85°C。
低关断电流(低于 10µA)
1% 反馈电压精度 (25°C)
从预偏置输出电压中启动
逐周期过流限制
器件信息(1)
断续模式欠压保护
非锁存过压保护 (OVP),欠压闭锁 (UVLO) 和热关
断 (TSD) 保护
订货编号
TPS562210A
TPS563210A
封装
封装尺寸(标称值)
DDF(8)
1.60mm x 2.90mm
•
•
可调软启动
电源正常输出
(1) 要了解所有可用封装,请参见数据表末尾的可订购产品附录。
2 应用
•
•
•
•
数字电视电源
高清 蓝光 (Blu-ray) 碟片™播放器
网络家庭终端设备
数字机顶盒(STB)
空白
空白
简化电路原理图
效率
TPS562210A
TPS563210A
100
90
80
70
60
50
40
1
8
GND
VBST
2
7
6
5
VOUT
EN
VFB
SS
EN
SW
3
4
VIN
VIN
PG
VOUT
30
Vout = 5V
Copyright
©
2016, Texas Instruments Incorporated
20
Vout = 3.3V
10
Vout = 1.8V
0
0.001
0.01
0.1
1
10
Output Current (A)
C015
1
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. PRODUCTION DATA.
English Data Sheet: SLVSDP9
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
目录
7.4 Device Functional Modes........................................ 12
Application and Implementation ........................ 13
8.1 Application Information............................................ 13
8.2 Typical Application ................................................. 13
Power Supply Recommendations...................... 21
1
2
3
4
5
6
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 4
6.1 Absolute Maximum Ratings ...................................... 4
6.2 ESD Ratings ............................................................ 4
6.3 Recommended Operating Conditions....................... 4
6.4 Thermal Information.................................................. 4
6.5 Electrical Characteristics........................................... 5
6.6 Timing Requirements................................................ 5
6.7 Typical Characteristics.............................................. 6
Detailed Description ............................................ 10
7.1 Overview ................................................................. 10
7.2 Functional Block Diagram ...................................... 10
7.3 Feature Description................................................. 11
8
9
10 Layout................................................................... 22
10.1 Layout Guidelines ................................................. 22
10.2 Layout Example .................................................... 22
11 器件和文档支持 ..................................................... 23
11.1 器件支持 ............................................................... 23
11.2 相关链接................................................................ 23
11.3 接收文档更新通知 ................................................. 23
11.4 社区资源................................................................ 23
11.5 商标....................................................................... 23
11.6 静电放电警告......................................................... 23
11.7 Glossary................................................................ 23
12 机械、封装和可订购信息....................................... 23
7
4 修订历史记录
日期
修订版本
注释
2016 年 11 月
*
最初发布版本。
2
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
5 Pin Configuration and Functions
DDF Package
8 Pin
Top View
GND
SW
1
8
VBST
2
3
7
6
5
EN
VFB
SS
VIN
PG
4
Pin Functions
PIN
DESCRIPTION
NAME
NO.
Ground pin Source terminal of low-side power NFET as well as the ground terminal for controller circuit. Connect
sensitive VFB to this GND at a single point.
GND
1
SW
VIN
PG
2
3
4
5
6
7
8
Switch node connection between high-side NFET and low-side NFET.
Input voltage supply pin. The drain terminal of high-side power NFET.
Power good open drain output
SS
Soft-start control. An external capacitor should be connected to GND.
Converter feedback input. Connect to output voltage with feedback resistor divider.
Enable input control. Active high and must be pulled up to enable the device.
Supply input for the high-side NFET gate drive circuit. Connect 0.1 µF capacitor between VBST and SW pins.
VFB
EN
VBST
Copyright © 2016, Texas Instruments Incorporated
3
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
6 Specifications
6.1 Absolute Maximum Ratings
TJ = -40°C to 150°C (unless otherwise noted)
(1)
MIN
–0.3
–0.3
–0.3
–0.3
–0.3
–0.3
–2
MAX
19
UNIT
V
VIN, EN
VBST
25
V
VBST (10 ns transient)
27.5
6.5
6.5
5.5
19
V
VBST (vs SW)
Input voltage range
V
VFB, PG
V
SS
SW
V
V
SW (10 ns transient)
Operating junction temperature, TJ
Storage temperature, Tstg
–3.5
–40
–55
21
V
150
150
°C
°C
(1) Stresses beyond those listed under Absolute Maximum Ratings may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Conditions. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
±2000
±500
UNIT
V
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001(1)
Charged device model (CDM), per JEDEC specification JESD22-C101(2)
V(ESD)
Electrostatic discharge
V
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
TJ = –40°C to 150°C (unless otherwise noted)
MIN
MAX
17
23
26
6
UNIT
V
VIN
Supply input voltage range
VBST
4.5
–0.1
–0.1
–0.1
–0.1
–0.1
–0.1
–1.8
–3.5
–40
V
VBST (10 ns transient)
V
VBST(vs SW)
V
EN
17
5.5
5
V
VI
Input voltage range
VFB, pg
V
SS
V
SW
17
20
85
V
SW (10 ns transient)
V
TA
Operating free-air temperature
°C
6.4 Thermal Information
TPS562210A
TPS563210A
DDF (8 PINS)
THERMAL METRIC(1)
UNIT
RθJA
RθJC(top)
RθJB
ψJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
106.1
49.1
10.9
8.6
87.0
41.6
14.6
4.7
°C/W
°C/W
°C/W
°C/W
°C/W
Junction-to-top characterization parameter
Junction-to-board characterization parameter
ψJB
10.8
14.6
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
4
Copyright © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
6.5 Electrical Characteristics
over operating free-air temperature range, VIN = 12 V (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY CURRENT
IVIN
Operating – non-switching supply current
Shutdown supply current
VIN current, TA = 25°C, EN = 5V, VFB = 0.8 V
VIN current, TA = 25°C, EN = 0 V
190
3.0
290
10
µA
µA
IVINSDN
LOGIC THRESHOLD
VENH
VENL
REN
EN high-level input voltage
EN
1.6
V
V
EN low-level input voltage
EN pin resistance to GND
EN
0.6
VEN = 12 V
225
450
900
kΩ
VFB VOLTAGE AND DISCHARGE RESISTANCE
TA = 25°C, VO = 1.05 V, IO = 10 mA, Eco-mode™
operation
VFB threshold voltage TPS562210A
772
765
mV
TA = 25°C, VO = 1.05 V
758
753
751
772
777
779
±0.1
VFBTH
VFB threshold voltage TPS562210A and
TPS563210A
TA = 0°C to 85°C, VO = 1.05 V(1)
TA = -40°C to 85°C, VO = 1.05 V(1)
VFB = 0.8 V, TA = 25°C
mV
µA
IVFB
VFB input current
0
MOSFET
TA = 25°C, VBST – SW = 5.5 V, TPS562210A
TA = 25°C, VBST – SW = 5.5 V, TPS563210A
TA = 25°C, TPS562210A
133
68
RDS(on)h
High side switch resistance
Low side switch resistance
mΩ
mΩ
80
RDS(on)l
CURRENT LIMIT
TA = 25°C, TPS563210A
39
DC current, VOUT = 1.05 V , L1 = 2.2 µH, TPS562210A
DC current, VOUT = 1.05 V , L1 = 1.5 µH, TPS563210A
2.5
3.5
3.2
4.2
4.3
5.3
IOCL
Current limit(1)
A
THERMAL SHUTDOWN
Shutdown temperature
Hysteresis
155
35
TSDN
Thermal shutdown threshold(1)
°C
SOFT START
ISS
SS charge current
VSS = 1.2 V
4.2
85%
0.5
6
7.8
µA
POWER GOOD
VFB rising (Good)
VFB falling (Fault)
PG = 0.5 V
90%
85%
1
95%
VTHPG
PG threshold
IPG
PG sink current
mA
OUTPUT UNDERVOLTAGE AND OVERVOLTAGE PROTECTION
125%x
Vfbth
VOVP
VUVP
Output OVP threshold
Output UVP threshold
OVP Detect
65%x
Vfbth
Hiccup detect
tHiccupOn
tHiccupOff
UVLO
Hiccup Power On Time
Hiccup Power Off Time
Relative to soft start time
Relative to soft start time
1
7
cycle
cycles
Wake up VIN voltage
Hysteresis VIN voltage
3.45
0.13
3.75
0.32
4.05
0.55
UVLO
UVLO threshold
V
(1) Not production tested.
6.6 Timing Requirements
MIN
TYP
MAX
UNIT
ON-TIME TIMER CONTROL
tON
On time
VIN = 12 V, VO = 1.05 V
TA = 25°C, VFB = 0.5 V
150
260
ns
ns
tOFF(MIN)
Minimum off time
310
Copyright © 2016, Texas Instruments Incorporated
5
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
6.7 Typical Characteristics
6.7.1 TPS562210A Characteristics
VIN = 12 V (unless otherwise noted)
300
250
200
150
100
50
6
5
4
3
2
1
0
0
0
50
100
150
0
50
100
150
œ50
œ50
Junction Temperature (°C)
Junction Temperature (°C)
C011
C012
图 1. Supply Current vs Junction Temperature
图 2. VIN Shutdown Current vs Junction Temperature
0.780
0.775
0.770
0.765
0.760
0.755
0.750
60
50
40
30
20
10
0
-10
0
50
100
150
0
3
6
9
12
15
18
œ50
Junction Temperature (°C)
EN Input Voltage (V)
C013
C014
图 3. VFB Voltage vs Junction Temperature
图 4. EN Current vs EN Voltage
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
Vout = 5V
Vout = 3.3V
Vout = 1.8V
Vout = 3.3V
Vout = 1.8V
0.001
0.01
0.1
1
10
0.001
0.01
0.1
1
10
Output Current(A)
Output Current (A)
C016
C015
VI = 5 V
图 6. Efficiency vs Output Current
图 5. Efficiency vs Output Current
6
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
TPS562210A Characteristics (接下页)
800
800
700
600
500
400
300
200
100
0
Vo = 0.76V
Vo = 1.05V
Vo = 6.5V
Vo = 0.75V
750
Vo = 1.05V
700
Vo = 6.5V
650
600
550
500
450
400
4
6
8
10
12
14
16
18
0.01
0.1
Output Current (A)
1
10
Input Voltage (V)
C017
C018
图 7. Switching Frequency vs Input Voltage
图 8. Switching Frequency vs Output Current
版权 © 2016, Texas Instruments Incorporated
7
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
6.7.2 TPS563210A Characteristics
VIN = 12V (unless otherwise noted)
300
250
200
150
100
50
6
5
4
3
2
1
0
0
0
50
100
150
0
50
100
150
œ50
œ50
Junction Temperature (°C)
Junction Temperature (°C)
C019
C020
图 9. Supply Current vs Junction Temperature
图 10. VIN Shutdown Current vs Junction Temperature
0.780
0.775
0.770
0.765
0.760
0.755
0.750
60
50
40
30
20
10
0
œ10
0
50
100
150
0
3
6
9
12
15
18
œ50
Junction Temperature (°C)
EN Input Voltage (V)
C021
C022
图 11. VFB Voltage vs Junction Temperature
图 12. EN Current vs EN Voltage
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
Vout = 5V
Vout = 3.3V
Vout = 1.8V
Vout = 3.3V
Vout = 1.8V
0.001
0.01
0.1
1
10
0.001
0.01
0.1
1
10
Output Current (A)
Output Current (A)
C023
C024
VI = 5 V
图 13. Efficiency vs Output Current
图 14. Efficiency vs Output Current
8
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
TPS563210A Characteristics (接下页)
800
800
700
600
500
400
300
200
100
0
Vo = 0.76V
Vo = 0.76V
Vo = 1.05V
Vo = 6.5V
750
Vo = 1.05V
700
Vo = 6.5V
650
600
550
500
450
400
4
6
8
10
12
14
16
18
0.01
0.1
Output Current (A)
1
10
Input Voltage (V)
C025
C026
图 15. Switching Frequency vs Input Voltage
图 16. Switching Frequency vs Output Current
版权 © 2016, Texas Instruments Incorporated
9
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
7 Detailed Description
7.1 Overview
The TPS562210A and TPS563210A are 2-A, 3-A synchronous step-down converters. The proprietary D-CAP2™
mode control supports low ESR output capacitors such as specialty polymer capacitors and multi-layer ceramic
capacitors without complex external compensation circuits. The fast transient response of D-CAP2™ mode
control can reduce the output capacitance required to meet a specific level of performance.
7.2 Functional Block Diagram
EN
7
3
VIN
VUVP
+
Hiccup
VREG5
Control Logic
UVP
Regulator
UVLO
+
OVP
VOVP
VFB
SS
6
5
8
2
VBST
SW
PWM
Voltage
Ref
+
Reference
+
HS
SS
Soft Start
Ton
One-Shot
XCON
VREG 5
LS
TSD
OCL
threshold
PG
4
OCL
+
1
GND
+
+
VTHPG
ZC
Copyright © 2016, Texas Instruments Incorporated
10
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
7.3 Feature Description
7.3.1 The Adaptive On-Time Control and PWM Operation
The main control loop of the TPS562210A and TPS563210A are adaptive on-time pulse width modulation (PWM)
controller that supports a proprietary D-CAP2™ mode control. The D-CAP2™ mode control combines adaptive
on-time control with an internal compensation circuit for pseudo-fixed frequency and low external component
count configuration with both low ESR and ceramic output capacitors. It is stable even with virtually no ripple at
the output.
At the beginning of each cycle, the high-side MOSFET is turned on. This MOSFET is turned off after internal one
shot timer expires. This one shot duration is set proportional to the converter input voltage, VIN, and inversely
proportional to the output voltage, VO, to maintain a pseudo-fixed frequency over the input voltage range, hence
it is called adaptive on-time control. The one-shot timer is reset and the high-side MOSFET is turned on again
when the feedback voltage falls below the reference voltage. An internal ramp is added to reference voltage to
simulate output ripple, eliminating the need for ESR induced output ripple from D-CAP2™ mode control.
7.3.2 Soft Start and Pre-Biased Soft Start
The TPS562210A and TPS563210A have adjustable soft-start. When the EN pin becomes high, the SS charge
current (ISS) begins charging the capacitor which is connected from the SS pin to GND (CSS). Smooth control of
the output voltage is maintained during start up. The equation for the soft start time, Tss is shown in 公式 1.
Css´ VFBTH ´ 0.86
Tss(ms) =
Iss
(1)
where VFBTH is 0.765 V and Iss is 6 µA.
If the output capacitor is pre-biased at startup, the devices initiate switching and start ramping up only after the
internal reference voltage becomes greater than the feedback voltage VFB. This scheme ensures that the
converters ramp up smoothly into regulation point.
7.3.3 Power Good
The power good output, PG is an open drain output. The power good function becomes active after 1.7 times
soft-start time. When the output voltage becomes within –10% of the target value, internal comparators detect
power good state and the power good signal becomes high. If the feedback voltage goes under 15% of the target
value, the power good signal becomes low.
7.3.4 Current Protection
The output over-current limit (OCL) is implemented using a cycle-by-cycle valley detect control circuit. The switch
current is monitored during the OFF state by measuring the low-side FET drain to source voltage. This voltage is
proportional to the switch current. To improve accuracy, the voltage sensing is temperature compensated.
During the on time of the high-side FET switch, the switch current increases at a linear rate determined by VIN,
VOUT, the on-time and the output inductor value. During the on time of the low-side FET switch, this current
decreases linearly. The average value of the switch current is the load current IOUT. If the monitored current is
above the OCL level, the converter maintains low-side FET on and delays the creation of a new set pulse, even
the voltage feedback loop requires one, until the current level becomes OCL level or lower. In subsequent
switching cycles, the on-time is set to a fixed value and the current is monitored in the same manner. If the over
current condition exists consecutive switching cycles, the internal OCL threshold is set to a lower level, reducing
the available output current. When a switching cycle occurs where the switch current is not above the lower OCL
threshold, the counter is reset and the OCL threshold is returned to the higher value.
There are some important considerations for this type of over-current protection. The load current is higher than
the over-current threshold by one half of the peak-to-peak inductor ripple current. Also, when the current is being
limited, the output voltage tends to fall as the demanded load current may be higher than the current available
from the converter. This may cause the output voltage to fall. When the VFB voltage falls below the UVP
threshold voltage, the UVP comparator detects it. And then, the device will shut down after the UVP delay time
(typically 14 µs) and re-start after the hiccup time.
When the over current condition is removed, the output voltage returns to the regulated value.
版权 © 2016, Texas Instruments Incorporated
11
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
Feature Description (接下页)
7.3.5 Over Voltage Protection
TPS562210A and TPS563210A detect over voltage condition by monitoring the feedback voltage (VFB). When
the feedback voltage becomes higher than 125% of the target voltage, the OVP comparator output goes high
and the high-side MOSFET is turns off. This function is non-latch operation.
7.3.6 UVLO Protection
Under voltage lock out protection (UVLO) monitors the internal regulator voltage. When the voltage is lower than
UVLO threshold voltage, the device is shut off. This protection is non-latching.
7.3.7 Thermal Shutdown
The device monitors the temperature of itself. If the temperature exceeds the threshold value (typically 155°C),
the device is shut off. This is a non-latch protection.
7.4 Device Functional Modes
7.4.1 Advanced Eco-Mode™ Control
The TPS562210A and TPS563210A are designed with Advanced Eco-mode™ to maintain high light load
efficiency. As the output current decreases from heavy load condition, the inductor current is also reduced and
eventually comes to point that its rippled valley touches zero level, which is the boundary between continuous
conduction and discontinuous conduction modes. The rectifying MOSFET is turned off when the zero inductor
current is detected. As the load current further decreases the converter runs into discontinuous conduction mode.
The on-time is kept almost the same as it was in the continuous conduction mode so that it takes longer time to
discharge the output capacitor with smaller load current to the level of the reference voltage. This makes the
switching frequency lower, proportional to the load current, and keeps the light load efficiency high. The transition
point to the light load operation IOUT(LL) current can be calculated in 公式 2.
V
IN - VOUT ´ V
)
(
1
OUT
IOUT(LL)
=
´
2´L ´ fSW
V
IN
(2)
12
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
8 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TPS562210A and TPS563210A are typically used as step down converters, which convert a voltage from
4.5 V to 17 V to a lower voltage. Webench software is available to aid in the design and analysis of circuits.
8.2 Typical Application
8.2.1 Typical Application, TPS562210A
4.5-V to 17-V Input, 1.05-V Output Converter.
U1
TPS562210A
L1 2.2uH
VIN = 4.5 - 17 V
C5
VOUT = 1.05 V, 2 A
3
7
8
VIN
VIN
EN
VBST
VOUT
0.1µF
R4
100k
R3 10.0k
C1
0.1µF
C2
10µF
C3
10µF
C6
22µF
C7
22µF
C8
22µF
2
4
6
1
EN
SW
PG
R1
3.74k
PG
5
SS
VFB
GND
C4
8200pF
R2
10.0k
图 17. TPS562210A 1.05V/2A Reference Design
8.2.1.1 Design Requirements
For this design example, use the parameters shown in 表 1.
表 1. Design Parameters
PARAMETER
Input voltage range
VALUES
4.5 V to 17 V
1.05 V
Output voltage
Output current
2 A
Output voltage ripple
20 mVp-p
8.2.1.2 Detailed Design Procedure
8.2.1.2.1 Output Voltage Resistors Selection
The output voltage is set with a resistor divider from the output node to the VFB pin. It is recommended to use
1% tolerance or better divider resistors. Start by using 公式 3 to calculate VOUT
.
To improve efficiency at light loads consider using larger value resistors, too high of resistance are more
susceptible to noise and voltage errors from the VFB input current are more noticeable.
R1
æ
ö
VOUT = 0.765´ 1+
ç
÷
R2
è
ø
(3)
8.2.1.2.2 Output Filter Selection
The LC filter used as the output filter has double pole at:
1
F =
P
2p LOUT ´ COUT
(4)
13
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
At low frequencies, the overall loop gain is set by the output set-point resistor divider network and the internal
gain of the device. The low frequency phase is 180 degrees. At the output filter pole frequency, the gain rolls off
at a –40 dB per decade rate and the phase drops rapidly. D-CAP2™ introduces a high frequency zero that
reduces the gain roll off to –20 dB per decade and increases the phase to 90 degrees one decade above the
zero frequency. The inductor and capacitor for the output filter must be selected so that the double pole of 公式 4
is located below the high frequency zero but close enough that the phase boost provided be the high frequency
zero provides adequate phase margin for a stable circuit. To meet this requirement use the values recommended
in 表 2.
表 2. TPS562210A Recommended Component Values
L1 (µH)
Output Voltage (V)
R2 (kΩ)
R3 (kΩ)
C6 + C7 + C8 (µF)
MIN
1.5
1.5
1.5
1.5
1.5
2.2
2.2
3.3
3.3
TYP
2.2
2.2
2.2
2.2
2.2
3.3
3.3
4.7
4.7
MAX
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
1
1.05
1.2
1.5
1.8
2.5
3.3
5
3.09
3.74
5.76
9.53
13.7
22.6
33.2
54.9
75
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
6.5
The inductor peak-to-peak ripple current, peak current and RMS current are calculated using 公式 5, 公式 6 and
公式 7. The inductor saturation current rating must be greater than the calculated peak current and the RMS or
heating current rating must be greater than the calculated RMS current.
Use 650 kHz for fSW. Make sure the chosen inductor is rated for the peak current of 公式 6 and the RMS current
of 公式 7.
V
- VOUT
VOUT
´
IN(MAX)
IlP-P
=
V
LO ´ ƒSW
IN(MAX)
(5)
(6)
IlP-P
IlPEAK = IO +
2
1
2
2
ILO(RMS)
=
IO
+
IlP-P
12
(7)
For this design example, the calculated peak current is 2.34 A and the calculated RMS current is 2.01 A. The
inductor used is a TDK CLF7045T-2R2N with a peak current rating of 5.5 A and an RMS current rating of 4.3 A.
The capacitor value and ESR determines the amount of output voltage ripple. The TPS562210A and
TPS563210A are intended for use with ceramic or other low ESR capacitors. Recommended values range from
20µF to 68µF. Use 公式 8 to determine the required RMS current rating for the output capacitor.
VOUT ´ VIN - VOUT
(
12 ´ V ´LO ´ ƒSW
)
ICO(RMS)
=
IN
(8)
For this design, two TDK C3216X5R0J226M 22 µF output capacitors are used. The typical ESR is 2 mΩ each.
The calculated RMS current is 0.286A and each output capacitor is rated for 4A.
8.2.1.2.3 Input Capacitor Selection
The TPS562210A and TPS563210A require an input decoupling capacitor and a bulk capacitor is needed
depending on the application. A ceramic capacitor over 10 µF is recommended for the decoupling capacitor. An
additional 0.1 µF capacitor (C3) from pin 3 to ground is optional to provide additional high frequency filtering. The
capacitor voltage rating needs to be greater than the maximum input voltage.
14
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
8.2.1.2.4 Bootstrap capacitor Selection
A 0.1µF ceramic capacitor must be connected between the VBST to SW pin for proper operation. It is
recommended to use a ceramic capacitor.
8.2.1.3 Application Curves
The following application curves were generated using the application circuit of 图 17.
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN = 5V
VIN = 12V
VIN = 5V
VIN = 12V
0
0
4
0.5
1
1.5
2
0.001
0.01 0.02 0.05 0.1 0.2
Output Current (A)
0.5
1
2 3 45
Output Current (A)
D006
D007
图 18. TPS562210A Efficiency
图 19. TPS562210A Light Load Efficiency
1
0.8
0.6
0.4
0.2
0
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-0.2
-0.4
-0.6
-0.8
-1
0.5
1
1.5
2
0
0.5
1
1.5
2
Output Current (A)
Output Current (A)
D008
D009
图 20. TPS562210A Load Regulation, VI = 5 V
图 21. TPS562210A Load Regulation, VI = 12 V
0.5
0.4
0.3
0.2
0.1
0
IO = 2 A
VI = 50 mV / div (ac coupled)
SW = 5 V / div
-0.1
-0.2
-0.3
-0.4
-0.5
6
8
10
12
14
16
18
Time = 1 µsec / div
图 23. TPS562210A Input Voltage Ripple
Input Voltage (V)
D010
图 22. TPS562210A Line Regulation
版权 © 2016, Texas Instruments Incorporated
15
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
IO = 200 mA
IO = 0 A
VO = 20 mV / div (ac coupled)
VO = 20 mV / div (ac coupled)
SW = 5 V / div
SW = 5 V / div
Time = 1 µsec / div
Time = 5 msec / div
图 24. TPS562210A Output Voltage Ripple
图 25. TPS562210A Output Voltage Ripple
IO = 2 A
VO = 20 mV / div (ac coupled)
VO = 50 mV / div (ac coupled)
IO = 500 mA / div
SW = 5 V / div
Load step = 0.5 A - 1.5 A
Slew rate = 500 mA / µsec
Time = 200 µsec / div
Time = 1 µsec / div
图 27. TPS562210A Transient Response
图 26. TPS562210A Output Voltage Ripple
VI = 10V/ div
SS = 5V/ div
EN = 10V/ div
SS = 5V/ div
VO = 500mV/ div
PG = 1V/ div
VO = 500mV/ div
PG = 1V/ div
Time = 1 msec / div
Time = 1 msec / div
图 28. TPS562210A Start Up Relative To VI
图 29. TPS562210A Start Up Relative To En
16
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
VI = 10V/ div
EN = 10V/ div
SS = 5V/ div
SS = 5V/ div
VO = 500mV/ div
VO = 500mV/ div
PG = 1V/ div
PG = 1V/ div
Time = 5 msec / div
图 30. TPS562210A Shut Down Relative To VI
Time = 5 msec / div
图 31. TPS562210A Shut Down Relative To EN
版权 © 2016, Texas Instruments Incorporated
17
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
8.2.2 Typical Application, TPS563210A
4.5-V To 17-V Input, 1.05-V Output Converter.
U1
TPS563210A
L1 1.5uH
VIN = 4.5 - 17 V
C5
VOUT = 1.05 V, 3 A
3
7
8
VIN
VIN
EN
VBST
VOUT
0.1µF
R4
100k
R3 10.0k
C1
0.1µF
C2
10µF
C3
10µF
C6
22µF
C7
22µF
C8
22µF
2
4
6
1
EN
SW
PG
R1
3.74k
PG
5
SS
VFB
GND
C4
8200pF
R2
10.0k
图 32. TPS563210A 1.05 V / 3A Reference Design
8.2.2.1 Design Requirements
For this design example, use the parameters shown in 表 3.
表 3. Design Parameters
PARAMETER
Input voltage range
Output voltage
VALUE
4.5 V to 17 V
1.05 V
Output current
3 A
Output voltage ripple
20 mVpp
8.2.2.2 Detailed Design Procedures
The detailed design procedure for TPS563210A is the same as for TPS562210A except for inductor selection.
8.2.2.2.1 Output Filter Selection
表 4. TPS563210A Recommended Component Values
L1 (µH)
Output Voltage (V)
R2 (kΩ)
R3 (kΩ)
C6 + C7 + C8 (µF)
MIN
1.0
1.0
1.0
1.0
1.5
1.5
1.5
2.2
2.2
TYP
1.5
1.5
1.5
1.5
2.2
2.2
2.2
3.3
3.3
MAX
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
4.7
1
1.05
1.2
1.5
1.8
2.5
3.3
5
3.09
3.74
5.76
9.53
13.7
22.6
33.2
54.9
75
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
10.0
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
20 - 68
6.5
The inductor peak-to-peak ripple current, peak current and RMS current are calculated using 公式 9, 公式 10 and
公式 11. The inductor saturation current rating must be greater than the calculated peak current and the RMS or
heating current rating must be greater than the calculated RMS current. Use 650 kHz for ƒSW
.
Use 650 kHz for ƒSW. Make sure the chosen inductor is rated for the peak current of 公式 10 and the RMS
current of 公式 11.
V
- VOUT
VOUT
´
IN(MAX)
IlP-P
=
V
LO ´ ƒSW
IN(MAX)
(9)
18
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
IlP-P
IlPEAK = IO +
2
(10)
(11)
1
2
2
ILO(RMS)
=
IO
+
IlP-P
12
For this design example, the calculated peak current is 3.505 A and the calculated RMS current is 3.014 A. The
inductor used is a TDK CLF7045T-1R5N with a peak current rating of 7.3-A and an RMS current rating of 4.9-A.
The capacitor value and ESR determines the amount of output voltage ripple. The TPS563209 is intended for
use with ceramic or other low ESR capacitors. Recommended values range from 20 μF to 68 μF. Use 公式 7 to
determine the required RMS current rating for the output capacitor. For this design three TDK C3216X5R0J226M
22 μF output capacitors are used. The typical ESR is 2 mΩ each. The calculated RMS current is 0.292A and
each output capacitor is rated for 4 A.
8.2.2.3 Application Curves
The following application curves were generated using the application circuit of 图 32.
100
90
80
70
60
50
40
30
20
10
0
100
90
80
70
60
50
40
30
20
10
0
VIN = 5V
VIN = 12V
VIN = 5V
VIN = 12V
0
0.5
1
1.5
2
2.5
3
0.001
0.01 0.02 0.05 0.1 0.2
Output Current (A)
0.5
1
2 3 45
Output Current (A)
D001
D002
图 33. TPS563210A Efficiency
图 34. TPS563210A Light Load Efficiency
1
0.8
0.6
0.4
0.2
0
1
0.8
0.6
0.4
0.2
0
-0.2
-0.4
-0.6
-0.8
-1
-0.2
-0.4
-0.6
-0.8
-1
0
0.5
1
1.5
2
2.5
3
0
0.5
1
1.5
2
2.5
3
Output Current (A)
Output Current (A)
D003
D004
图 35. TPS563210A Load Regulation, VI = 5 V
图 36. TPS563210A Load Regulation, VI = 12 V
版权 © 2016, Texas Instruments Incorporated
19
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
0.5
0.4
0.3
0.2
0.1
0
IO = 3 A
VI = 50 mV / div (ac coupled)
SW = 5 V / div
-0.1
-0.2
-0.3
-0.4
-0.5
4
6
8
10
12
14
16
18
Time = 1 µsec / div
Input Voltage (V)
D005
图 38. TPS563210A Input Voltage Ripple
图 37. TPS563210A Line Regulation
IO = 0 A
IO = 300 mA
VO = 20 mV / div (ac coupled)
VO = 20 mV / div (ac coupled)
SW = 5 V / div
SW = 5 V / div
Time = 1 µsec / div
Time = 5 msec / div
图 39. TPS563210A Output Voltage Ripple
图 40. TPS563210A Output Voltage Ripple
IO = 3 A
VO = 20 mV / div (ac coupled)
VO = 50 mV / div (ac coupled)
SW = 5 V / div
IO = 1 A / div
Load step = 0.75 A - 2.25 A
Slew rate = 500 mA / µsec
Time = 200 µsec / div
Time = 1 µsec / div
图 42. TPS563210A Transient Response
图 41. TPS563210A Output Voltage Ripple
20
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
VI = 10V/ div
EN = 10V/ div
SS = 5V/ div
SS = 5V/ div
VO = 500mV/ div
PG = 1V/ div
VO = 500mV/ div
PG = 1V/ div
Time = 1 msec / div
图 43. TPS563210A Start Up Relative To VI
Time = 1 msec / div
图 44. TPS563210A Start Up Relative To EN
EN = 10V/ div
VI = 10V/ div
SS = 5V/ div
SS = 5V/ div
VO = 500mV/ div
VO = 500mV/ div
PG = 1V/ div
PG = 1V/ div
Time = 5 msec / div
图 46. TPS563210A Shut Down Relative To EN
Time = 5 msec / div
图 45. TPS563210A Shut Down Relative To VI
9 Power Supply Recommendations
The TPS562210A and TPS563210A are designed to operate from input supply voltage in the range of 4.5 V to
17 V. Buck converters require the input voltage to be higher than the output voltage for proper operation. The
maximum recommended operating duty cycle is 65%. Using that criteria, the minimum recommended input
voltage is VO / 0.65.
版权 © 2016, Texas Instruments Incorporated
21
TPS562210A, TPS563210A
ZHCSFR5 –NOVEMBER 2016
www.ti.com.cn
10 Layout
10.1 Layout Guidelines
1. VIN and GND traces should be as wide as possible to reduce trace impedance. The wide areas are also of
advantage from the view point of heat dissipation.
2. The input capacitor and output capacitor should be placed as close to the device as possible to minimize
trace impedance.
3. Provide sufficient vias for the input capacitor and output capacitor.
4. Keep the SW trace as physically short and wide as practical to minimize radiated emissions.
5. Do not allow switching current to flow under the device.
6. A separate VOUT path should be connected to the upper feedback resistor.
7. Make a Kelvin connection to the GND pin for the feedback path.
8. Voltage feedback loop should be placed away from the high-voltage switching trace, and preferably has
ground shield.
9. The trace of the VFB node should be as small as possible to avoid noise coupling.
10. The GND trace between the output capacitor and the GND pin should be as wide as possible to minimize its
trace impedance.
10.2 Layout Example
GND
VOUT
Additional
Vias to the
GND plane
OUTPUT
CAPACITOR
Vias to the
internal SW
node copper
BOOST
CAPACITOR
OUTPUT
INDUCTOR
FEEDBACK
RESISTORS
GND
SW
VIN
SS
VBST
EN
TO ENABLE
CONTROL
TPS56x10A
VFB
PG
VIN
Vias to the
internal SW
node copper
HIGH FREQUENCY
INPUT BYPASS
CAPACITOR
POWER GOOD
SW node copper
pour area on internal
or bottom layer
INPUT BYPASS
CAPACITOR
PG PULL UP
RESISTOR
SLOW START
CAPACITOR
VIA TO INTERNAL
GROUND PLANE
TO PG PULL
UP VOLTAGE
22
版权 © 2016, Texas Instruments Incorporated
TPS562210A, TPS563210A
www.ti.com.cn
ZHCSFR5 –NOVEMBER 2016
11 器件和文档支持
11.1 器件支持
11.2 相关链接
下面的表格列出了快速访问链接。范围包括技术文档、支持和社区资源、工具和软件,以及样片或购买的快速访
问。
表 5. 相关链接
器件
产品文件夹
请单击此处
请单击此处
样片与购买
请单击此处
请单击此处
技术文档
请单击此处
请单击此处
工具与软件
请单击此处
请单击此处
支持与社区
请单击此处
请单击此处
TPS562210A
TPS563210A
11.3 接收文档更新通知
如需接收文档更新通知,请访问 www.ti.com.cn 网站上的器件产品文件夹。点击右上角的提醒我 (Alert me) 注册
后,即可每周定期收到已更改的产品信息。有关更改的详细信息,请查阅已修订文档中包含的修订历史记录。
11.4 社区资源
The following links connect to TI community resources. Linked contents are provided "AS IS" by the respective
contributors. They do not constitute TI specifications and do not necessarily reflect TI's views; see TI's Terms of
Use.
TI E2E™ Online Community TI's Engineer-to-Engineer (E2E) Community. Created to foster collaboration
among engineers. At e2e.ti.com, you can ask questions, share knowledge, explore ideas and help
solve problems with fellow engineers.
Design Support TI's Design Support Quickly find helpful E2E forums along with design support tools and
contact information for technical support.
11.5 商标
D-CAP2, Eco-mode, E2E are trademarks of Texas Instruments.
蓝光 (Blu-ray) 碟片 is a trademark of Blu-ray Disc Association.
11.6 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
11.7 Glossary
SLYZ022 — TI Glossary.
This glossary lists and explains terms, acronyms, and definitions.
12 机械、封装和可订购信息
以下页中包括机械、封装和可订购信息。这些信息是针对指定器件可提供的最新数据。这些数据会在无通知且不对
本文档进行修订的情况下发生改变。欲获得该数据表的浏览器版本,请查阅左侧的导航栏。
版权 © 2016, Texas Instruments Incorporated
23
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS562210ADDFR
TPS562210ADDFT
TPS563210ADDFR
TPS563210ADDFT
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
ACTIVE SOT-23-THIN
DDF
DDF
DDF
DDF
8
8
8
8
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
SN
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
-40 to 85
-40 to 85
2210A
SN
SN
SN
2210A
3210A
3210A
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Dec-2020
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE OUTLINE
DDF0008A
SOT-23 - 1.1 mm max height
S
C
A
L
E
4
.
0
0
0
PLASTIC SMALL OUTLINE
C
2.95
2.65
SEATING PLANE
TYP
PIN 1 ID
AREA
0.1 C
A
6X 0.65
8
1
2.95
2.85
NOTE 3
2X
1.95
4
5
0.38
0.22
8X
0.1
C A B
1.65
1.55
B
1.1 MAX
0.20
0.08
TYP
SEE DETAIL A
0.25
GAGE PLANE
0.1
0.0
0 - 8
0.6
0.3
DETAIL A
TYPICAL
4222047/C 10/2022
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. This dimension does not include mold flash, protrusions, or gate burrs. Mold flash, protrusions, or gate burrs shall not
exceed 0.15 mm per side.
www.ti.com
EXAMPLE BOARD LAYOUT
DDF0008A
SOT-23 - 1.1 mm max height
PLASTIC SMALL OUTLINE
8X (1.05)
SYMM
1
8
8X (0.45)
SYMM
6X (0.65)
5
4
(R0.05)
TYP
(2.6)
LAND PATTERN EXAMPLE
SCALE:15X
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
METAL
SOLDER MASK
DEFINED
NON SOLDER MASK
DEFINED
SOLDER MASK DETAILS
4222047/C 10/2022
NOTES: (continued)
4. Publication IPC-7351 may have alternate designs.
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
DDF0008A
SOT-23 - 1.1 mm max height
PLASTIC SMALL OUTLINE
8X (1.05)
SYMM
(R0.05) TYP
8
1
8X (0.45)
SYMM
6X (0.65)
5
4
(2.6)
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
SCALE:15X
4222047/C 10/2022
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
7. Board assembly site may have different recommendations for stencil design.
www.ti.com
重要声明和免责声明
TI“按原样”提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,
不保证没有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担
保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他功能安全、信息安全、监管或其他要求。
这些资源如有变更,恕不另行通知。TI 授权您仅可将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。
您无权使用任何其他 TI 知识产权或任何第三方知识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成
本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款或 ti.com 上其他适用条款/TI 产品随附的其他适用条款的约束。TI 提供这些资源并不会扩展或以其他方式更改
TI 针对 TI 产品发布的适用的担保或担保免责声明。
TI 反对并拒绝您可能提出的任何其他或不同的条款。IMPORTANT NOTICE
邮寄地址:Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2022,德州仪器 (TI) 公司
相关型号:
TPS563210DDFR
17 V Input, 3A Synchronous Step-Down Regulator in SOT-23 with Advanced Eco-mode™, PG & SS 8-SOT-23-THIN -40 to 125
TI
TPS563210_15
TPS56x210, 4.5-V to 17-V Input, 2-A, 3-A Synchronous Step-Down Voltage Regulator In 8-Pin SOT-23
TI
TPS563211DRLR
采用 SOT583 封装且具有 1% 精度、PG/SS 和 PFM/强制 PWM 的 4.2V 至 17V、3A 同步降压转换器 | DRL | 8 | -40 to 125
TI
TPS563219DDFT
17 V Input, 3A Synchronous Step-Down Regulator in SOT-23 with Power-good and Soft-start 8-SOT-23-THIN -40 to 125
TI
©2020 ICPDF网 联系我们和版权申明