TPS62912 [TI]
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation;型号: | TPS62912 |
厂家: | TEXAS INSTRUMENTS |
描述: | TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation |
文件: | 总36页 (文件大小:3792K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
TPS62912,TPS62913
SLVSFP4 – AUGUST 2020
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with
Integrated Ferrite Bead Filter Compensation
1 Features
3 Description
•
Low output 1/f noise < 20 µVRMS (100 Hz to 100
kHz)
The TPS6291x devices are a family of high efficiency
low noise and low ripple synchronous buck
converters. The devices are ideal for noise sensitive
applications that would normally use an LDO for post
regulation such as high speed ADCs, Clock and Jitter
Cleaner, Serializer, De-serializer, and Radar
applications.
•
Low output voltage ripple < 10 µVRMS after ferrite
bead
High PSRR of > 80 dB (up to 100 kHz)
2.2-MHz or 1-MHz fixed frequency peak current
mode control
•
•
•
•
Synchronizable with external clock (optional)
Integrated loop compensation supports ferrite
bead for second stage L-C filter (optional)
Spread spectrum modulation (optional)
3.0-V to 17-V input voltage range
0.8-V to 5.5-V output voltage range
57-mΩ/20-mΩ RDSon
Output voltage accuracy of ±1%
Precise enable input allows
– User-defined undervoltage lockout
– Exact sequencing
The device operates at a fixed switching frequency of
2.2 MHz or 1 MHz, and can be synchronized to an
external clock.
•
•
•
•
•
•
To further reduce the output voltage ripple, the device
integrates loop compensation to operate with an
optional second-stage ferrite bead L-C filter. This
allows an output voltage ripple below 10 µVRMS
.
Low-frequency noise levels, similar to a low-noise
LDO, are achieved by filtering the internal voltage
reference with a capacitor connected to the NR/SS
pin.
•
•
•
•
•
•
Adjustable soft start
Power-good output
Output discharge (optional)
-40°C to 150°C junction temperature range
2.0-mm x 2.0-mm QFN with 0.5-mm pitch
Create a custom design using the TPS6291x with
the WEBENCH® Power Designer
The optional spread spectrum modulation scheme
spreads the DC/DC switching frequency over a wider
span, which lowers the mixing spurs.
Device Information
DEVICE
NAME
OUTPUT
CURRENT
PACKAGE (1)
BODY SIZE (NOM)
TPS62912 2 A
TPS62913 3 A
QFN (10)
2.0 mm x 2.0 mm
2 Applications
(1) For all available packages, see the orderable addendum at
the end of the data sheet.
•
•
•
•
Telecom infrastructure
Test and measurement
Aerospace and defense (radar/avionics)
Medical
Ferrite
Bead
2.2µH
Vin
12V
SW
VO
FB
Vo
3.3V/3A
VIN
EN/SYNC
S-CONF
2x10µF
3x22µF
15.4k
4.87k
2.2nF
2x22µF
PSNS
PGND
NR/SS
PG
470nF
Typical Application
Output Noise vs Frequency
An IMPORTANT NOTICE at the end of this data sheet addresses availability, warranty, changes, use in safety-critical applications,
intellectual property matters and other important disclaimers. ADVANCE INFORMATION for preproduction products; subject to change
without notice.
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
Table of Contents
1 Features............................................................................1
2 Applications.....................................................................1
3 Description.......................................................................1
4 Revision History.............................................................. 2
5 Pin Configuration and Functions...................................3
Pin Functions.................................................................... 3
6 Specifications.................................................................. 4
6.1 Absolute Maximum Ratings ....................................... 4
6.2 ESD Ratings .............................................................. 4
6.3 Recommended Operating Conditions ........................4
6.4 Thermal Information ...................................................5
6.5 Electrical Characteristics ............................................5
6.6 Typical Characteristics................................................7
7 Detailed Description......................................................15
7.1 Overview...................................................................15
7.2 Functional Block Diagram.........................................15
7.3 Feature Description...................................................16
7.4 Device Functional Modes..........................................18
8 Application and Implementation..................................20
8.1 Application Information............................................. 20
8.2 Typical Applications.................................................. 20
9 Power Supply Recommendations................................27
10 Layout...........................................................................27
10.1 Layout Guidelines................................................... 27
10.2 Layout Example...................................................... 28
11 Device and Documentation Support..........................29
11.1 Device Support........................................................29
11.2 Receiving Notification of Documentation Updates..29
11.3 Support Resources................................................. 29
11.4 Trademarks............................................................. 29
11.5 Electrostatic Discharge Caution..............................29
11.6 Glossary..................................................................29
12 Mechanical, Packaging, and Orderable
Information.................................................................... 30
4 Revision History
DATE
REVISION
NOTES
August 2020
*
Initial release
Copyright © 2020 Texas Instruments Incorporated
2
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
5 Pin Configuration and Functions
PGND
4
5
6
3
VO
2 SW
EN/SYNC
PG
VIN
1
10
9
7
8
Figure 5-1. 10-Pin QFN RPU Package (Top View)
Pin Functions
PIN
I/O
DESCRIPTION
NO.
NAME
Enable/Disable Pin including threshold-comparator. Connect to logic low to disable the device. Pull high to enable the device.
This pin has an internal pulldown resistor of typically 500 kΩ when the device is disabled. Apply a clock to this pin to
synchronize the device.
1
EN/SYNC
I
2
3
4
SW
I/O Switch pin of the power stage
VO
I
Output voltage sense pin. This pin needs to be connected directly after the first inductor.
Power ground connection
PGND
Open-drain power-good output. This pin is pulled to GND when Vout is below the power-good threshold. It requires a pullup
resistor to output a logic high. It can be left open or tied to GND if not used.
5
PG
O
6
7
VIN
I
I
Power supply input voltage pin
PSNS
NR/SS
FB
Power Sense Ground. Connect directly to the ground plane.
A capacitor connected to this pin sets the soft-start time and low frequency noise level of the device.
Feedback pin of the device
8
O
I
9
10
S-CONF
O
Smart Configuration Pin. This pin configures the operation modes of the device. See Table 7-1.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
3
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
6 Specifications
6.1 Absolute Maximum Ratings
over operating junction temperature range (unless otherwise noted)(1)
MIN
– 0.3
– 0.3
– 2.5
– 0.3
– 0.3
MAX
18
UNIT
V
VIN, EN/SYNC, PG, S-CONF
SW (DC)
VIN + 0.3
21
V
Voltage(2)
SW (AC, less than 10ns)(3)
VO, FB, NR/SS
PSNS
V
6
V
0.3
V
Sink Current
PG
10
mA
°C
°C
TJ
Junction temperature
Storage temperature
–40
–65
150
150
Tstg
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under
Recommended Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device
reliability.
(2) All voltage values are with respect to the network ground terminal
(3) While switching
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per ANSI/ESDA/JEDEC JS-001,
all pins(1)
±2000
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per JEDEC specification
JESD22-C101, all pins(2)
±500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating junction temperature range (unless otherwise noted)
MIN
3.0
0.8
5
NOM
MAX
17
UNIT
VIN
VOUT
CIN
L1
Input voltage
V
V
Output voltage
5.5
Effective input capacitance
Effective output inductance
Effective output capacitance
Effective filter inductance
Effective filter capacitance
10
2.2 / 4.7
47
µF
µH
µF
nH
µF
µF
A
-30%
40
0
20%
80
COUT
Lf
10
50
Cf
20
40
0
40
160
200
3
COUT + Cf Effective total output capacitance, including first and second L-C filter
IOUT
IOUT
Output current for TPS62913
Output current for TPS62912
Junction temperature
0
2
A
(1)
TJ
–40
150
°C
(1) Operating lifetime is reduced at junction temperatures above 125°C.
Copyright © 2020 Texas Instruments Incorporated
4
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
6.4 Thermal Information
TPS6291x
THERMAL METRIC(1)
RPU 10-pin QFN
UNIT
JEDEC 51-7 PCB
TPS6291xEVM-077
RθJA
RθJC(top)
RθJB
ΨJT
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
87.7
61.9
22.2
1.9
56.6
n/a (2)
n/a (2)
1.3
°C/W
°C/W
°C/W
°C/W
°C/W
Junction-to-top characterization parameter
Junction-to-board characterization parameter
ΨJB
22.2
22.7
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
(2) Not applicable to an EVM
6.5 Electrical Characteristics
Over recommended input voltage range, TJ = -40℃ to 150℃. Typical values are at Vin = 12V and TJ = 25℃
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
SUPPLY
EN/SYNC = High, no load, device
switching, fsw = 1 MHz
IQ
Quiescent current
5
mA
ISD
Shutdown current
EN/SYNC = GND, TJ = -40°C to 125°C
VIN rising, TJ = -40°C to 125°C
VIN rising
0.2
70
3.0
µA
V
VUVLO
VUVLO
VHYS
Under voltage lockout
2.85
2.92
Under voltage lockout
3.04
V
Under voltage lockout hysteresis
Thermal shutdown threshold
Thermal shutdown hysteresis
200
170
20
mV
°C
°C
TJ rising
TJ falling
TJSD
CONTROL and INTERFACE
High-level input-threshold voltage at EN/
SYNC
VH_EN
EN/SYNC rising
EN/SYNC falling
EN/SYNC = clock
EN/SYNC = clock
0.97
0.87
1.1
1.01
0.9
1.04
0.93
V
V
V
V
Low-level input-threshold voltage at EN/
SYNC
VL_EN
High-level input-threshold clock signal on
EN/SYNC
VH_SYNC
VL_SYNC
IEN,LKG
RPD
Low-level input-threshold clock signal on
EN/SYNC
0.4
EN/SYNC = GND or VIN, -40℃ ≤ TJ ≤
125℃
Input leakage current into EN/SYNC
Pull-down resistor on EN/SYNC
Enable delay time
1
500
1
100
nA
kΩ
ms
µA
%
EN/SYNC = Low
330
Time from EN/SYNC high to device starts
switching, RS-CONF = 80.6kΩ
tdelay
INR/SS
NR/SS source current
67.5
-4
75
82.5
+4
RS-CONF tolerance for all settings
according to S-CONF Table
RS-CONF S-CONF resistor step range accuracy
VPG
Power good threshold
VFB rising, referenced to VFB nominal
VFB falling, referenced to VFB nominal
ISINK = 1 mA
93
88
95
90
98
93
%
%
VPG
Power good threshold
VPG,OL
IPG,LKG
tPG
Low-level output voltage at PG pin
Input leakage current into PG pin
Power good deglitch time
0.4
500
V
VPG = 5 V, -40℃ ≤ TJ ≤ 125℃
VFB falling
1
8
nA
µs
OUTPUT
ton
Minimum on-time
VIN ≥ 5V, Iout = 1A
35
70
ns
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
5
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
6.5 Electrical Characteristics (continued)
Over recommended input voltage range, TJ = -40℃ to 150℃. Typical values are at Vin = 12V and TJ = 25℃
(unless otherwise noted)
PARAMETER
TEST CONDITIONS
VIN ≥ 5V, Iout = 1A
MIN
TYP
50
MAX
60
UNIT
ns
V
toff
Minimum off-time
VFB
Feedback regulation accuracy
Feedback regulation accuracy
Feedback regulation accuracy
Input leakage current into FB
Input leakage current into VO
-40℃ ≤ TJ ≤ 150℃
0.792
0.792
0.796
0.8
0.812
0.808
0.804
70
VFB
-40℃ ≤ TJ ≤ 125℃
0.8
V
VFB
TJ = 25℃
0.8
V
IFB,LKG
IVO,LKG
VFB = 0.8V, -40℃ ≤ TJ ≤ 125℃
VVO = 1.2V, -40℃ ≤ TJ ≤ 125℃
VIN = 12V, 1.2VOUT, CNR/SS = 470nF, fsw
0.01
0.01
nA
µA
30
=
PSRR
PSRR
VNRMS
VNRMS
VOPP
Power supply rejection ratio
Power supply rejection ratio
Output voltage RMS noise
Output voltage RMS noise
Output ripple voltage at fSW
Output ripple voltage at fSW
1MHz, CFF = open, L1 = 2.2µH, COUT
3x22µF, 100kHz ≤ f ≤ 3MHz
=
50
40
dB
VIN = 5V, 1.2VOUT, CNR/SS = 470nF, fsw
2.2MHz, CFF = open, L1 = 2.2µH, COUT
3x22µF, 100kHz ≤ f ≤ 3MHz
=
=
dB
VIN = 12V, BW = 100Hz to 100kHz, CNR/
SS = 470nF, fSW = 1MHz, VOUT = 1.2V,
CFF = open, L1 = 2.2µH, COUT = 3 x 22 µF
24.4
13.5
9
µVRMS
µVRMS
µVRMS
µVRMS
VIN = 5V, BW = 100Hz to 100kHz, CNR/
SS = 470nF, fSW = 2.2MHz, VOUT = 1.2V,
CFF = open, L1 = 2.2µH, COUT = 3 x 22µF
VIN = 12V, fSW = 1MHz, VOUT = 1.2V, L1 =
4.7µH, COUT = 3x22µF, Lf = 10nH, Cf =
2x22µF
VIN = 5V, fSW = 2.2MHz, VOUT = 1.2V, L1 =
2.2µH, COUT = 3x22µF, Lf = 10nH, Cf =
2x22uF
VOPP
< 2.2
EN/SYNC = GND, VOUT = 1.2V, VIN ≥ 5V.
See Typical Char for plot.
RDIS
RDIS
Output discharge resistance
Output discharge resistance
7
Ω
Ω
EN/SYNC = GND, VOUT = 5V, VIN ≥ 5V.
See Typical Char for plot.
32
fSW
Switching frequency
2.2-MHz setting
2.2-MHz setting
1-MHz setting
1-MHz setting
1.98
1.9
2.2
2.2
1
2.42
2.42
1.18
1.2
MHz
MHz
MHz
MHz
%
fSYNC
fSW
fSYNC
DSYNC
Synchronization range
Switching frequency
0.9
Synchronization range
Synchronization duty cycle
0.86
45
1
55
Phase delay from EN/SYNC rising edge
to SW rising edge
tsync_delay Synchronization phase delay
90
3.5
ns
A
A
A
A
A
Peak switch current limit, see Current
ISWpeak
Limit
TPS62912
TPS62913
TPS62912
TPS62913
2.9
3.7
4.0
5.1
Peak switch current limit, see Current
ISWpeak
Limit
4.3
Valley switch current limit, see Current
ISWvalley
Limit
3.4
Valley switch current limit, see Current
ISWvalley
Limit
4.2
Negative valley current limit, see Current
Ineg_valley
Limit
-1.53
-0.96
High-side FET on-resistance
RDS(ON)
VIN ≥ 5V
VIN ≥ 5V
57
20
95
39
mΩ
mΩ
Low-side FET on-resistance
Copyright © 2020 Texas Instruments Incorporated
6
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
6.6 Typical Characteristics
VIN=12 V, VOUT=1.2 V, TA=25°C, BOM = Table 8-1, (unless otherwise noted)
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
First L-C Only
12 V to 1.2 V, 1A
2.2 μH, 1 MHz
First L-C Only
Figure 6-1. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-2. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
First and second L-C
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
First and second L-C
Figure 6-3. VOUT Ripple After the Second L-C Filter
Figure 6-4. VOUT Ripple FFT After the Second L-C
Filter
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
First L-C Only
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
First and second L-C
With Random Spread Spectrum Enabled
With Random Spread Spectrum Enabled
Figure 6-5. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-6. VOUT Ripple After the Second L-C Filter
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
7
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
12 V to 1.8 V, 1 A
2.2 μH, 1 MHz
First L-C Only
12 V to 1.8 V, 1A
2.2 μH, 1 MHz
First L-C Only
Figure 6-7. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-8. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
12 V to 1.8 V, 1 A
2.2 μH, 1 MHz
First and second L-C
12 V to 1.8 V, 1 A
2.2 μH, 1 MHz
First and second L-C
Figure 6-9. VOUT Ripple After the Second L-C Filter
Figure 6-10. VOUT Ripple FFT After the Second L-C
Filter
12 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
12 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
Figure 6-11. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-12. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
Copyright © 2020 Texas Instruments Incorporated
8
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
12 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
12 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
Figure 6-13. VOUT Ripple After the Second L-C
Filter
Figure 6-14. VOUT Ripple FFT After the Second L-C
Filter
5 V to 1.2 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
5 V to 1.2 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
Figure 6-15. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-16. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
5 V to 1.2 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
5 V to 1.2 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
Figure 6-17. VOUT Ripple after the Second L-C Filter
Figure 6-18. VOUT Ripple FFT After the Second L-C
Filter
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
9
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
5 V to 1.8 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
5 V to 1.8 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
Figure 6-19. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-20. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
5 V to 1.8 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
5 V to 1.8 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
Figure 6-21. VOUT Ripple After the Second L-C
Filter
Figure 6-22. VOUT Ripple FFT After the Second L-C
Filter
5 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
5 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz
First L-C Only
Figure 6-23. VOUT Ripple After the First L-C Filter
(VOUT-Mid)
Figure 6-24. VOUT Ripple FFT After the First L-C
Filter (VOUT-Mid)
Copyright © 2020 Texas Instruments Incorporated
10
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
5 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
5 V to 3.3 V, 1 A
2.2 μH, 2.2 MHz First and second L-C
Figure 6-25. VOUT Ripple After the Second L-C
Filter
Figure 6-26. VOUT Ripple FFT After the Second L-C
Filter
12 V to 1.2 V
2.2 μH, 1 MHz
First L-C Only
12 V to 1.2 V, 1 A
2.2 μH, 1 MHz
S-CONF = OFF,
Random
NR/SS = Open, 100 nF, 470 nF, 2.2 μF, BW = 100 Hz to 100
kHz
Figure 6-27. Spread Spectrum FFT
Figure 6-28. Output Noise Density vs Frequency
12 V to 1.8 V
2.2 μH, 1 MHz
First L-C Only
12 V to 1.2 V
2.2 μH, 1 MHz
First L-C Only
NR/SS = Open, 100 nF, 470 nF, 2.2 μF, BW = 100 Hz to 100
kHz
NR/SS = 470 nF, CFF = Open, 100 nF, 1 μF
Figure 6-29. Output Noise Density vs Frequency
Figure 6-30. Output Noise Density vs Frequency
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
11
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
12 V to 1.8 V
2.2 μH, 1 MHz
First L-C Only
12 V to 3.3 V
2.2 μH, 2.2 MHz
First L-C Only
NR/SS = 470 nF, CFF = Open, 100 nF, 1 μF
NR/SS = Open, 100 nF, 470 nF, 2.2 μF, BW = 100 Hz to 100
kHz
Figure 6-31. Output Noise Density vs Frequency
Figure 6-32. Output Noise Density vs Frequency
5 V to 1.2 V
2.2 μH, 2.2 MHz
First L-C Only
12 V to 3.3 V
2.2 μH, 2.2 MHz
First L-C Only
NR/SS = Open, 100 nF, 470 nF, 2.2 μF, BW = 100 Hz to 100
kHz
NR/SS = 470 nF, CFF = Open, 100 nF, 1 μF
Figure 6-33. Output Noise Density vs Frequency
Figure 6-34. Output Noise Density vs Frequency
5 V to 3.3 V
2.2 μH, 2.2 MHz
First L-C Only
12 V to 1.2 V
2.2 μH, 1 MHz
1 A, 2 A, 3 A
First L-C Only
NR/SS = Open, 100 nF, 470 nF, 2.2 μF, BW = 100 Hz to 100
kHz
Figure 6-36. PSRR vs Frequency
Figure 6-35. Output Noise Density vs Frequency
Copyright © 2020 Texas Instruments Incorporated
12
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
VIN = 5 V
VIN = 5 V
Figure 6-37. High-Side RDS(ON) vs Junction
Temperature
Figure 6-38. Low-Side RDS(ON) vs Junction
Temperature
1 MHz, 2 A
5 Vin to 0.8 Vout
1 MHz
Figure 6-39. FB Pin Voltage Error vs Input Voltage
Figure 6-40. Output Voltage Error vs Load
12 Vin to 0.8 Vout
1 MHz
12 Vin
1 MHz
Figure 6-41. Output Voltage Error vs Load
Figure 6-42. Oscillator Frequency vs Temperature
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
13
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
12 Vin
2.2 MHz
VIN: 3 V, 5 V, 12 V
Figure 6-43. Oscillator Frequency vs Temperature
Figure 6-44. Shutdown Current vs Temperature
VIN: 12 V
25°C
Figure 6-45. Output Discharge Resistance vs Output Voltage
Copyright © 2020 Texas Instruments Incorporated
14
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
7 Detailed Description
7.1 Overview
The TPS6291x low-noise, low-ripple synchronous buck converter is a fixed frequency current mode converter.
The converter has a filtered internal reference to achieve a low-noise output similar to low noise LDOs. The
converter achieves lower output voltage ripple by using a switching frequency of either 2.2 MHz or 1 MHz and a
larger inductance. The output voltage ripple can be further reduced by adding a small second stage L-C filter to
the output. This can be a ferrite bead or a small inductor, followed by an output capacitor. Internal compensation
maintains stability with an external filter inductor up to 50 nH. To avoid voltage drops across this second stage
filter, the device regulates the output voltage after the filter. The TPS6291x family supports an optional spread
spectrum modulation. When powering ADCs, for example, spread spectrum modulation reduces the mixing
spurs. Switching frequency, spread spectrum modulation, and output discharge are set using the S-CONF pin.
7.2 Functional Block Diagram
PG
VIN
High Side
Current Sense
+
VPG
VFB
t
Slope
Compensation
Undervoltage
lockout
+
EN/SYNC
G
t
1.0V
Thermal shutdown
Clock
Detector
MUX
MOSFET Driver
Anti Shoot Through
Converter Control Logic
EN/SYNC
SW
1MHz/2.2MHz
MODE
MODE
Spread Spectrum
Modulation
Low Side
Current Sense
PGND
VIN
Comparator
FB
2nd stage filter
compensation
t
GM
VO
Start-up readout
ADC
+
S-CONF
Register
Selection
VIN
MODE
S-CONF
GM Amplifier
INR/SS
Softstart
Rf
RDIS
VREF
0.8V
Output voltage
MODE
discharge
logic
PSNS
NR/SS
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
15
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
7.3 Feature Description
7.3.1 Smart Config (S-CONF)
This S-CONF pin configures the device based on the resistor value. This pin is read after EN/SYNC goes high.
The device configuration cannot be changed during operation. The S-CONF value is re-read if EN is pulled
below 200 mV or if VIN falls below UVLO. Table 7-1 shows the configuration options of switching frequency,
spread spectrum modulation, output discharge, and synchronization.
Table 7-1. S-CONF Device Configuration Modes
SWITCHING
FREQUENCY
OUTPUT
DISCHARGE
S-CONF
SPREAD SPECTRUM
SYNCHRONIZATION
VIN
2.2 MHz
1 MHz
OFF
OFF
OFF
OFF
No
GND
No
4.87 kΩ
7.5 kΩ
9.31 kΩ
14.3 kΩ
2.2 MHz
2.2 MHz
1 MHz
OFF
OFF
1.9 MHz to 2.42 MHz
Random
OFF
OFF
No
0.9 MHz to 1.2 MHz
No
OFF
1 MHz
Random
OFF
Discharge On
ON
18.2 kΩ
22.1 kΩ
27.4 kΩ
42.2 kΩ
52.3 kΩ
80.6 kΩ
2.2 MHz
1 MHz
OFF
OFF
No
ON
No
2.2 MHz
2.2 MHz
1 MHz
OFF
ON
1.9 MHz to 2.42 MHz
Random
OFF
ON
No
0.9 MHz to 1.2 MHz
No
ON
1 MHz
Random
ON
7.3.2 Device Enable (EN/SYNC)
The device is enabled by pulling the EN/SYNC pin high, and has an accurate rising threshold voltage of typically
1.01 V. Once the device is enabled, the operation mode is set by the configuration of the S-CONF pin. This
occurs during the device start-up delay time tdelay. Once tdelay expires, the internal soft-start circuitry ramps up
the output voltage over the soft-start time set by the CNR/SS capacitor. The start-up delay time tdelay varies
depending on the selected S-CONF value. It is shortest with smaller S-CONF resistors.
The EN/SYNC pin has an active pulldown resistor RPD. This prevents an uncontrolled start-up of the device, in
case the EN/SYNC pin cannot be driven to a low level. The pulldown resistor is disconnected after start-up. With
EN set to a low level, the device enters shutdown and the pulldown resistor is activated again.
7.3.3 Device Synchronization (EN/SYNC)
The EN/SYNC pin is also used for device synchronization. Once a clock signal is applied to this pin, the device is
enabled and reads the configuration of the S-CONF pin. The external clock frequency must be within the clock
synchronization frequency range set by the S-CONF pin. When the clock signal changes from a clock to a static
high, then the device switches from external clock to internal clock. To shutdown the device when using an
external clock, EN/SYNC must go low for at least 10 µs.
The clock signal can be a logic signal with a logic level as specified in the electrical table, and can be applied
directly to the EN/SYNC pin. External logic, such as an AND gate, can be used to combine separate enable and
clock inputs, as shown in Figure 7-1.
TPS6291x
EN
EN/SYNC
CLK
Figure 7-1. Synchronization with Separate Enable Signal (optional)
Copyright © 2020 Texas Instruments Incorporated
16
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
7.3.4 Spread Spectrum Modulation
Using the S-CONF pin enables or disables spread spectrum modulation. DC/DC converters generate an output
voltage ripple at the switching frequency. When powering ADCs or an analog front-end (AFE), the switching
frequency generates high frequency mixing spurs as well as a low frequency spur in the output frequency
spectrum. Using the optional second stage L-C filter reduces the ripple of the converter and spurs by up to 30
dB. Using a random spread spectrum modulation also reduces the spurs in the output spectrum as shown in
Figure 6-2.
Spread spectrum uses a random modulation to spread the switching frequency over a larger frequency range.
The randomized modulation generates several lower amplitude spurs at frequencies below 10 kHz, and avoids a
single low frequency tone generated by the modulation frequency. The frequency spread is 20% of the switching
frequency with a modulation frequency of 180 Hz. The frequency spreading is shown in Figure 7-2.
Vo /dB
fSpread
fModulation
f
fsw
Figure 7-2. Randomized Spread Spectrum Modulation
7.3.5 Output Discharge
Output discharge is enabled or disabled, depending on the S-CONF setting. With output discharge enabled, the
output voltage is pulled low by a discharge resistor RDIS of typically 7 Ω. The output discharge function is
enabled during thermal shutdown, UVLO, or when EN/SYNC is pulled low.
7.3.6 Undervoltage Lockout (UVLO)
To avoid mis-operation of the device at low input voltages, the device is enabled once the input voltage is above
the undervoltage lockout threshold. The device is disabled once the input voltage falls below the undervoltage
threshold.
7.3.7 Power-Good Output
The device has a power-good output. The PG pin goes high impedance once the FB pin voltage is above 95% of
the nominal voltage, and is driven low once the voltage falls below typically 90% of the nominal voltage. Table
7-2 shows the typical PG pin logic. The PG pin is an open-drain output and is specified to sink up to 10 mA. The
power-good output requires a pullup resistor connecting to any voltage rail less than 18 V. The PG signal can be
used for sequencing of multiple rails by connecting to the EN pin of other converters. If not used, the PG pin can
be left floating or connected to GND. PG has a deglitch time of typically 8 μs before going low.
Table 7-2. Power Good Pin Logic
PG LOGIC STATUS
DEVICE STATE
HIGH IMPEDANCE
LOW
VFB ≥ VPG
√
Enabled (EN/SYNC = High)
VFB < VPG after tPG
√
√
Shutdown (EN/SYNC = Low)
UVLO
0.7 V < VIN < VUVLO
TJ > TJSD
√
√
Thermal Shutdown
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
17
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
Table 7-2. Power Good Pin Logic (continued)
PG LOGIC STATUS
DEVICE STATE
HIGH IMPEDANCE
LOW
Power Supply Removal
VIN < 0.7 V
√
7.3.8 Noise Reduction and Soft-Start Capacitor (NR/SS)
A capacitor connected to this pin reduces the low frequency noise of the converter and sets the soft-start time.
The larger the capacitor, the lower the noise and the longer the start-up time of the converter. A 470-nF capacitor
is typically connected to this pin for a start-up time of 5 ms, although longer and shorter start-up times can be
used. During soft start with a light load, the device skips switching pulses as needed to not discharge the output
voltage. The device can start into a pre-biased output voltage.
The device achieves low noise by adding an R-C filter to the reference voltage, as shown in Section 7.2. During
start-up, the NR/SS capacitor is charged with a constant current of 75 µA (typ) to 0.8 V. Larger NR/SS capacitors
provide for lower low frequency noise, as shown in Figure 6-28. The maximum NR/SS cap is 3.3 µF for a start-
up time of 35 ms. The minimum start-up time is set internally to 0.7 ms, which occurs when there is a small
NR/SS capacitor or no NR/SS capacitor.
7.3.9 Current Limit and Short Circuit Protection
The device is protected against short circuits and overcurrent. The switch current limit prevents the device from
high inductor current and from drawing excessive current from the input voltage rail. Excessive current can occur
with a shorted/saturated inductor or a heavy load/shorted output circuit condition. If the inductor current reaches
the threshold ISWpeak, the high-side MOSFET is turned off and the low-side MOSFET is turned on to ramp down
the inductor current. The high-side MOSFET is turned on again only when the low-side current is below the low-
side sourcing current limit ISWvalley
.
Due to internal propagation delay, the actual current can exceed the static current limit, especially if the input
voltage is high and very small inductances are used. The dynamic current limit is calculated as follows:
V
L
≈
’
Ipeak(typ) = ISWpeak
+
ìtPD
∆
«
÷
◊
L
(1)
where
•
•
•
•
ISWpeak is the static current limit, specified in Section 6.5
L is the inductance
VL is the voltage across the inductor (VIN - VOUT)
tPD is the internal propagation delay, typically 50 ns
The low-side MOSFET also contains a negative current limit to prevent excessive current from flowing back
through the inductor to the input. If the low-side sinking current limit is exceeded, the low-side MOSFET is turned
off. In this scenario, both MOSFETs are off until the start of the next cycle.
7.3.10 Thermal Shutdown
The device goes into thermal shutdown once the junction temperature exceeds typically 170°C with a 20°C
hysteresis.
7.4 Device Functional Modes
7.4.1 Fixed Frequency Pulse Width Modulation
To minimize output voltage ripple, the device operates in fixed frequency PWM operation down to no load. The
switching frequency of 1 MHz or 2.2 MHz is selected using the S-CONF pin.
Copyright © 2020 Texas Instruments Incorporated
18
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
7.4.2 Low Duty Cycle Operation
For high input voltages or low output voltages, the 70-nsec minimum on-time limits the maximum input to output
voltage difference and the switching frequency selected. When the minimum on-time is reached, the output
voltage rises above the regulation point. Refer to Table 8-2 for detailed design recommendations.
7.4.3 High Duty Cycle Operation (100% Duty Cycle)
The device offers a low input-to-output voltage differential by entering 100% duty cycle mode. In this mode, the
high-side MOSFET switch is constantly turned on. The minimum input voltage to maintain output voltage
regulation, depending on the load current and the output voltage level, is calculated as:
V
IN(min) =VOUT(min) + IOUT ì(RDS(ON) + R
L
)
(2)
where
•
•
•
•
VOUT(min) is the minimum output voltage the load can accept
IOUT is the output current
RDS(ON) is the RDS(ON) of the high-side MOSFET
RL is the DC resistance of the inductor used
To maintain fixed frequency switching, the device requires a minimum off-time of 50 ns (typ), 60 ns (max). If this
limit is reached during a switching pulse, the device skips switching pulses to maintain output voltage regulation.
If the input voltage decreases further, the device enters 100% mode.
7.4.4 Second Stage L-C Filter Compensation (Optional)
Most low-noise and low-ripple applications use a ferrite bead and bypass capacitor before the load. Using a
second L-C filter is especially useful for low-noise and low-ripple applications with constant load current such as
ADCs, DACs, and Jitter Cleaner. The second stage L-C filter is optional, and the device can be used without this
filter. Without the filter, the device has a low output voltage noise of typically 18.3 μVRMS shown in Figure 6-32
with an output voltage ripple of 280 μVRMS shown in Figure 6-12. The second stage L-C filter attenuates the
output voltage ripple by another approximately 30 dB shown in Figure 6-14. To improve load regulation, the
device can remote sense the output voltage after the second stage L-C filter and is internally compensated for
the additional double pole generated by the L-C filter.
To keep the second stage L-C filter as small as possible, the internal compensation is optimized for a 10-nH to
50-nH inductance. A small ferrite bead or even a PCB trace provides sufficient inductance for output voltage
ripple filtering. See Section 8.2.2.2.4 for details.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
19
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
8 Application and Implementation
Note
Information in the following applications sections is not part of the TI component specification, and TI
does not warrant its accuracy or completeness. TI’s customers are responsible for determining
suitability of components for their purposes. Customers should validate and test their design
implementation to confirm system functionality.
8.1 Application Information
The TPS6291x family of devices are optimized for low noise and low output voltage ripple.
8.2 Typical Applications
L1
2.2µH
Lf
10nH
TPS62913
Vin
12V
Vo
1.2V/3A
SW
VO
FB
VIN
COUT
3x22µF
EN/SYNC
S-CONF
CIN
2x10µF
C1
2.2nF
CFF
N/P
R1
2.49k
R4
52.3k
Cf
2x22µF
PSNS
PGND
NR/SS
PG
R2
4.87k
CNR/SS
470nF
Vo
R3
100k
Figure 8-1. Typical Schematic
Table 8-1 shows the list of components for the application curves in Section 8.2.2.3, unless otherwise noted.
Table 8-1. List of Components
REFERENCE
PART NUMBER
DESCRIPTION
MANUFACTURER
Texas Instruments
Coilcraft
Low Noise and Low Ripple buck
converter
TPS62913
TPS62913
L1
XGL4030-222MEC or XGL4030-472MEC
C2012X7S1E106K125AC
Inductor: 2.2 μH or 4.7 μH
Ceramic capacitors: 2x10µF ±10%
25-V Ceramic Capacitor X7S 0805
CIN
TDK
Ceramic capacitors: 3x22 µF, 10 V,
±20%, X7S, 0805
COUT
Lf
C2012X7S1A226M125AC
BLE18PS080SN1
TDK
MuRata
TDK
Ferrite Bead
Ceramic capacitor: 2x22 µF, 10 V,
±20%, X7S, 0805
Cf
C2012X7S1A226M125AC
GRM155R71H222KA01D
C1
Ceramic capacitor: 2200 pF, 50 V,
±10%, X7R, 0402
MuRata
CNR/SS, CFF
Ceramic capacitor
Resistor
Standard
Standard
R1, R2, R3, R4
8.2.1 Typical Design Recommendations
The external components have to fulfill the needs of the application, but also meet the stability criteria of the
control loop of the device. The device is optimized to work within a range of external components, and can be
optimized for efficiency, output ripple, component count, or lowest 1/f noise.
Typical applications that have input voltages of ≤ 6 V use a 2.2-µH inductor with a 2.2-MHz switching frequency.
Applications that have input voltages > 6 V can be optimized for efficiency using a 2.2-µH inductor with a 1-MHz
Copyright © 2020 Texas Instruments Incorporated
20
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
switching frequency. In this case, the output voltage ripple doubles compared to the use of a 4.7-µH inductor,
which is typically acceptable when powering high speed ADCs. Optimization for powering clock and PLL circuits
that need a 3.3-V output use a 2.2-µH inductor with 2.2-MHz switching frequency, minimizing output voltage
ripple and low frequency noise.
For the application cases that are not found in Table 8-2, there are two methods to design the TPS6291x circuit.
Section 8.2.2.1 uses Webench to design the circuit automatically or the calculations in Section 8.2.2.2 can be
used instead.
Table 8-2. Typical Single L-C Filter Design Recommendations
DESIGN GOAL
VIN
VOUT
FSW
INDUCTOR (2)
OUTPUT
CAPACITORS (3)
Typical
Typical
Typical
12 V (1)
12 V
≤ 2.0 V (1)
1 MHz
2.2 µH
4.7 µH
2.2 µH
3 x 22 µF, 10 V, 0805
3 x 22 µF, 10 V, 0805
2.0 V < VOUT ≤ 3.3 V 1 MHz
> 3.3 V 2.2 MHz
12 V
1 x 47 µF, 1210 and 2
x 22 µF, 10 V, 0805
Higher Efficiency
(with higher ripple and
noise)
12 V
2.0 V < VOUT ≤ 3.3 V 1 MHz
2.6 V ≤ VOUT ≤ 3.3 V 2.2 MHz
2.2 µH (4)
3 x 22 µF, 10 V, 0805
Low ripple/noise PLL 12 V
and Clock Supply
2.2 µH
3 x 22 µF, 10V, 0805
3 x 22 µF, 10 V, 0805
Typical
Typical
5 V
5 V
≤ 3.3 V
> 3.3V
2.2 MHz
2.2 MHz
2.2 µH
2.2 µH
1 x 47 µF, 1210 and 2
x 22 µF, 10 V, 0805
(1) The maximum input to output voltage difference is limited by the device maximum minimum on-time of 70ns. This is especially
important for input voltages above 12 V or output voltages below 1 V. See Section 8.2.2.2.1.
(2) For inductor part numbers, see Table 8-4.
(3) For output capacitor part numbers, see Table 8-5.
(4) The TPS62913 requires a 4.7-µH inductor when using the 1-MHz switching frequency to supply more than 2.5-A load current when the
output voltage is greater than 2.0 V.
The second stage L-C filter is optional, as the device can be used without this filter to achieve below 20-μVRMS
noise typically. A second stage filter is added to provide additional attenuation of the output ripple voltage. The
output voltage is sensed after the second L-C filter by connecting the FB resistors to the second stage L-C filter
capacitor. This provides remote sense, minimizing output voltage drop due to the ferrite bead. Refer to Table 8-3
for second stage L-C filter recommendations based on the output voltage.
Table 8-3. Second Stage L-C (Ferrite Bead) Filter Design Recommendations
VOUT (V)
≤ 3.3 V
FERRITE BEAD IMPEDANCE (AT 100 MHZ) (2)
OUTPUT CAPACITORS (1)
2 x 22 µF, 10 V, 0805
3 x 22 µF, 10 V, 0805
8 to 20 Ω
8 to 20 Ω
> 3.3 V
(1) For output capacitor part numbers, see Table 8-5.
(2) For second stage L-C filter part numbers, see Table 8-6.
8.2.2 Detailed Design Procedure
If the specific design is not found in Table 8-2, WEBENCH is recommended to generate the design. Alternatively,
the manual design procedure in External Component Selection can be followed.
8.2.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the TPS6291x device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost.
3. Open the advanced tab to optimize for output voltage ripple.
4. Once in a TPS6291x design, you can enable the second stage L-C filter and change other settings from the
drop-down on the left.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
21
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
•
•
•
Run electrical simulations to see important waveforms and circuit performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
8.2.2.2 External Component Selection
8.2.2.2.1 Switching Frequency Selection
The switching frequency can be chosen to optimize efficiency (1 MHz) or ripple/noise (2.2 MHz). Using the 2.2-
MHz setting increases the gain of the feedback loop and can result in lower output noise. However, additional
considerations for minimum on-time and duty cycle must also be considered. First, calculate the duty cycle using
Equation 3. Higher efficiency results in a shorter on-time, so a conservative approach is to use a higher
efficiency than expected in the application.
V
OUT
D =
VIN
ì
h
(3)
where:
η = estimated efficiency (use the value from the efficiency curves or 0.9 as an conservative assumption)
•
Then, calculate the on-time with both 1 MHz and 2.2 MHz using Equation 4. The on-time must always remain
above the minimum on-time of 70 nsec. Use the maximum input voltage and maximum efficiency to determine
the minimum duty cycle, Dmin. Use the maximum switching frequency for fSW
.
D
min
=
SW _ max
tON _ min
f
(4)
then
•
•
•
If tON_min min < 70 ns with 2.2 MHz, use 1 MHz.
If tON_min min < 70 ns with 1 MHz, reduce the maximum input voltage.
If tON_min min ≥ 70 ns for both cases, use 1 MHz for highest efficiency, or 2.2 MHz for lowest noise and ripple.
8.2.2.2.2 Inductor Selection for the First L-C Filter
The inductor selection is dependent on the selected switching frequency and the duty cycle. When using the 2.2-
MHz frequency, only use a 2.2-µH inductor. When using the 1-MHz frequency, calculate the maximum duty cycle
using the minimum input voltage. If Dmax is above 45%, only use a 4.7-µH inductor. If Dmax is below 45% and the
output voltage is 2 V or less, use only a 2.2-µH inductor. If Dmax is below 45% and the output voltage is above 2
V, use a 4.7-µH inductor to achieve the full output current or a 2.2-µH inductor for higher efficiency with a
reduced maximum output current.
The inductor also has to be rated for the appropriate saturation current. Equation 5 and Equation 6 calculate the
maximum inductor current under static load conditions. The formula takes the converter efficiency into account.
The calculation must be done for the maximum input voltage where the peak switch current is highest.
V
≈
V
OUT
’
OUT ì 1-
∆
÷
◊
h
VIN
ìh
«
DI =
L
fSW ìL
(5)
Copyright © 2020 Texas Instruments Incorporated
22
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
DI
2
L
IPEAK = IOUT +
(6)
where:
•
•
•
ƒSW is the switching frequency (typically 1 MHz or 2.2 MHz)
L = inductance
η = estimated efficiency (use the value from the efficiency curves or 0.9 as an conservative assumption)
Note
The calculation must be done for the maximum input voltage of the application.
Calculating the maximum inductor current using the actual operating conditions gives the minimum saturation
current. A margin of 20% is recommended to be added to cover for load transients during operation.
See Table 8-4 for typical inductors.
Table 8-4. Inductor Selection
INDUCTOR VALUE
2.2 µH
MANUFACTURER
Coilcraft
PART NUMBER
XGL4020-222
XGL4030-222
74438356022
74438357022
SIZE (L X W X H IN mm) ISAT/DCR (30% DROP)
4 x 4 x 2.1
6.2 A / 19.5 mΩ
7 A / 13.5 mΩ
5.2 A / 35 mΩ
7 A / 26 mΩ
2.2 µH
Coilcraft
4 x 4 x 3.1
2.2 µH
Wurth Elektronik
Wurth Elektronik
MuRata
4.1 x 4.1 x 2.1
4.1 x 4.1 x 3.1
2.2 µH
2.2 µH
DFE322520FD-2R2M=P2 3.2 x 2.5 x 2
5 A / 46 mΩ
4.7 µH
Coilcraft
XGL4020-472
XGL4030-472
4 x 4 x 2.1
4 x 4 x 3.1
4.1 A / 43.0 mΩ
4.4 A / 28.5 mΩ
3.4 A / 98 mΩ
4.7 µH
Coilcraft
4.7 µH for TPS62912 only MuRata
DFE322520FD-4R7M=P2 3.2 x 2.5 x 2
8.2.2.2.3 Output Capacitor Selection
The effective output capacitance can range from 40 μF (minimum) up to 200 μF (maximum) for a single L-C
system design. When using a second L-C filter, the first L-C filter must have output capacitance between 40 μF
and 80 μF, the second stage L-C filter (if used) must have at least 20 μF of capacitance, and the total
capacitance for both L-C filters must be less than 200 μF. Load transient testing and measuring the bode plot are
good ways to verify stability.
Ceramic capacitors (X5R or X7R) are recommended. Ceramic capacitors have a DC-Bias effect, which has a
strong influence on the final effective capacitance. Choose the right capacitor carefully in combination with
considering its package size and voltage rating. The ESR and ESL of the output capacitor are also important
considerations in selecting the output capacitors for low noise applications. Smaller package sizes typically have
lower ESL and ESR. 0805 or smaller packages are recommended, as long as they provide the required
capacitance and voltage rating for stable operation. Table 8-5 lists recommended output capacitors.
Table 8-5. Recommended Output Capacitors
CAPACITOR TYPE
Bulk Capacitor
CAPACITOR VALUE MANUFACTURER
VOLTAGE (V)
PACKAGE
0805
22 μF, X7S
47 μF, X7R
TDK C2012X7S1A226M125AC
Murata GRM32ER71A476ME15L
10
10
Bulk Capacitor
1210
8.2.2.2.4 Ferrite Bead Selection for Second L-C Filter
Using a ferrite bead for the second stage L-C filter minimizes the external component count because most of the
noise sensitive circuits use a RF bead for high frequency attenuation as a default component at their inputs.
It is important to select a ferrite bead with sufficiently high inductance at full load, and with low DC resistance
(below 10 mΩ) to keep the converter efficiency as high as possible. The ferrite bead inductance decreases with
increased load current. Therefore, the ferrite bead should have a current rating much higher than the desired
load current.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
23
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
The recommendation is to choose a ferrite bead with an impedance of 8 Ω to 20 Ω at 100 MHz. Refer to Table
8-6 for possible ferrite beads.
Table 8-6. Recommended Ferrite Beads
PART NUMBER
MANUFACTURER
SIZE
IMPEDANCE AT INDUCTANCE AT
DC RESISTANCE CURRENT
RATING
100 MHZ
100 MHz
(CALCULATED)
BLE18PS080SN1
74279221100
7427922808
MuRata
0603
1206
0603
8.5 Ω
10 Ω
8 Ω
13.5 nH
15.9 nH
12.7 nH
4 mΩ
3 mΩ
5 mΩ
5 A
Wurth Elektronik
Wurth Electronik
10.5 A
9.5 A
The internal compensation has been designed to be stable with up to 50 nH of inductance in the second stage
filter. To achieve low ripple, the second L-C filter requires only 5-nH to 10-nH inductance. The inductance can be
estimated from the ferrite bead impedance specification at 100 MHz, with the assumption that the inductance is
similar at the selected converter switching frequency of 1 MHz or 2.2 MHz, and can be verified through tools
available on some manufacturer websites. The inductance of a ferrite bead is calculated using Equation 7:
Z
L =
2ìp ì f
(7)
where
•
•
Z is the impedance of the ferrite bead in ohms at the specified frequency (usually 100 MHz)
f is the specified frequency (usually 100 MHz)
8.2.2.2.5 Input Capacitor Selection
For the best output and input voltage filtering, X5R or X7R ceramic capacitors are recommended. The input bulk
capacitor minimizes input voltage ripple, suppresses input voltage spikes, and provides a stable system rail for
the device. A 10-μF or larger input capacitor is recommended. Having two in parallel further improves the input
voltage ripple filtering, minimizing noise coupling into adjacent circuits. The voltage rating of the cap must also
be taken into consideration, and must provide the required 5-μF minimum effective capacitance after DC bias
derating.
In addition to the bulk input cap, a smaller cap must be placed directly from the VIN pin to the PGND pin to
minimize input loop parasitic inductance, thereby minimizing the high frequency noise of the device. The input
cap placement affects the output noise, so care needs to be taken in placing both the bulk cap and bypass caps
as shown in Section 10.2. Table 8-7 lists recommended input capacitors.
Table 8-7. Recommended Input Capacitors
INPUT CAP TYPE
CAPACITOR VALUE
MANUFACTURER
VOLTAGE RATING (V)
PACKAGE SIZE
Bulk Cap
10 μF, X7S
TDK
25
0805
C2012X7S1E106K125AC
Bypass Cap
2.2 nF, X7R
Murata
25
0402
GRM155R71E222KA01D
8.2.2.2.6 Setting the Output Voltage
Choose resistors R1 and R2 to set the output voltage within a range of 0.8 V to 5.5 V, according to Equation 8.
To keep the feedback network robust from noise, and to reduce the self-generated noise of resistors, set R2
equal to or lower than 5 kΩ. Lower values of FB resistors achieve better noise immunity, and lower light load
efficiency, as explained in the Design Considerations for a Resistive Feedback Divider in a DC/DC Converter
Technical Brief.
æ
ç
è
ö
VOUT
VFB
V
OUT
æ
ö
R1 = R2 ´
-1 = R2 ´
- 1
÷
÷
ç
0.8V
è
ø
ø
(8)
Copyright © 2020 Texas Instruments Incorporated
24
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
A feedforward capacitor (CFF) is not required for proper operation, but can further improve output noise.
However, care must be taken in choosing the CFF, since the power good (PG) function may not be valid with a
large CFF during start-up, and can cause spurious triggering of the PG pin during a large load transient. The
noise performance with various CFF is shown in Figure 6-29. Refer to the Pros and Cons Using a Feedforward
Capacitor with a Low Dropout Regulator Application Report for a discussion of the pros and cons of using a
feedforward capacitor.
8.2.2.2.7 NR/SS Capacitor Selection
As described in Section 7.3.8, the NR/SS cap affects both the total noise and the soft-start time. The
recommended value for a 5-ms soft-start time and good noise performance is 470 nF. The maximum NR/SS cap
is 3.3 μF for a start-up time of 35 ms. Values greater than 1 μF have minimal improvement in noise performance.
Use Equation 9 and Equation 10 to calculate the soft-start time based on desired soft-start time or the chosen
capacitor value.
C
NRSS *0.8
≈
’
tSS(s) =
∆
«
÷
◊
INRSS
(9)
I
NRSS ìtSS
(
)
CNRSS(F) =
0.8
(10)
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
25
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
8.2.2.3 Application Curves
VIN=12 V, VOUT=1.2 V, TA=25°C, BOM = Table 8-1, (unless otherwise noted)
0.8 Vout
2.2 μH, 1 MHz
1st L-C Only
1.2 Vout
2.2 μH, 1 MHz
1st L-C Only
Figure 8-2. Efficiency vs Load Current
Figure 8-3. Efficiency vs Load Current
1.8 Vout
2.2 μH, 1 MHz
1st L-C Only
3.3 Vout
4.7 μH, 1 MHz
1st L-C Only
Figure 8-4. Efficiency vs Load Current
Figure 8-5. Efficiency vs Load Current
3.3 Vout
2.2 μH, 2.2 MHz
1st L-C Only
5.4 Vout
2.2 μH, 2.2 MHz
1st L-C Only
Figure 8-6. Efficiency vs Load Current
Figure 8-7. Efficiency vs Load Current
Copyright © 2020 Texas Instruments Incorporated
26
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
5 V to 1.2 V
2.2 μH, 2.2 MHz
1st L-C Only
5 V to 1.8 V
2.2 μH, 2.2 MHz
1st L-C Only
Figure 8-8. Efficiency vs Load Current
Figure 8-9. Efficiency vs Load Current
12 V to 1.2 V
2.2 μH, 1 MHz
1st L-C Only
Figure 8-10. Output Voltage vs Load Current
9 Power Supply Recommendations
The power supply to the TPS6291x needs to have a current rating according to the supply voltage, output
voltage, and output current of the TPS6291x.
10 Layout
10.1 Layout Guidelines
A proper layout is critical for the operation of any switched mode power supply, especially at high switching
frequencies. Therefore, the PCB layout of the TPS6291x demands careful attention to ensure best performance.
A poor layout can lead to issues like bad line and load regulation, instability, increased EMI radiation, and noise
sensitivity. Refer to the Five Steps to a Great PCB Layout for a Step-Down Converter Technical Brief for a
detailed discussion of general best practices. Specific recommendations for the device are listed below.
•
The input capacitor or capacitors should be placed as close as possible to the VIN and PGND pins of the
device. This is the most critical component placement. Route the input capacitors directly to the VIN and
PGND pins avoiding vias.
•
•
Place the inductor close to the SW pin. Minimize the copper area at the switch node.
Place the output capacitor ground close to the PGND pin and route it directly avoiding vias. Minimize the
length of the connection from the inductor to the output capacitor.
•
Connect the VO pin directly to the first output capacitor, COUT
.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
27
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
•
Sensitive traces, such as the connections to the NR/SS, VO, and FB pins need to be connected with short
traces and be routed away from any noise source, such as the SW pin.
•
•
Connect the PSNS pin directly to the system GND plane with a via.
Place the second L-C filter, Lf and Cf, near the load to reduce any radiated coupling around the second L-C
filter
•
•
Place the FB resistors, R1 and R2, close to the FB pin and route the VOUT connection from R1 to the load as
a remote sense trace. If a second L-C filter is used, this connection should be made after Lf.
The recommended layout is implemented on the EVM and shown in its User's Guide, TPS6291xEVM-077
User's Guide, as well as in Figure 10-2.
10.2 Layout Example
CNR/SS
R2
R1
R4
CIN
VIN
GND
COUT
C1
PSNS
NR/SS
FB
S-CONF
L1
GND
VOUT
Figure 10-1. Recommended Layout for Single L-C Filter
CNR/SS
R2
CIN
R1
VIN
GND
R4
COUT
Cf
C1
PSNS
NR/SS
Lf
FB
S-CONF
L1
GND
VOUT
VOUT_FILT
Figure 10-2. Recommended Layout for Design with Second L-C Filter
Copyright © 2020 Texas Instruments Incorporated
28
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
11 Device and Documentation Support
11.1 Device Support
11.1.1 Third-Party Products Disclaimer
TI'S PUBLICATION OF INFORMATION REGARDING THIRD-PARTY PRODUCTS OR SERVICES DOES NOT
CONSTITUTE AN ENDORSEMENT REGARDING THE SUITABILITY OF SUCH PRODUCTS OR SERVICES
OR A WARRANTY, REPRESENTATION OR ENDORSEMENT OF SUCH PRODUCTS OR SERVICES, EITHER
ALONE OR IN COMBINATION WITH ANY TI PRODUCT OR SERVICE.
11.1.2 Development Support
11.1.2.1 Custom Design With WEBENCH® Tools
Click here to create a custom design using the TPS6291x device with the WEBENCH® Power Designer.
1. Start by entering the input voltage (VIN), output voltage (VOUT), and output current (IOUT) requirements.
2. Optimize the design for key parameters such as efficiency, footprint, and cost.
3. Open the advanced tab to optimize for output voltage ripple.
4. Once in a TPS6291x design, you can enable the second stage L-C filter and change other settings from the
drop-down on the left.
The WEBENCH Power Designer provides a customized schematic along with a list of materials with real-time
pricing and component availability.
In most cases, these actions are available:
•
•
•
Run electrical simulations to see important waveforms and circuit performance
Export customized schematic and layout into popular CAD formats
Print PDF reports for the design, and share the design with colleagues
Get more information about WEBENCH tools at www.ti.com/WEBENCH.
11.2 Receiving Notification of Documentation Updates
To receive notification of documentation updates, navigate to the device product folder on ti.com. Click on
Subscribe to updates to register and receive a weekly digest of any product information that has changed. For
change details, review the revision history included in any revised document.
11.3 Support Resources
TI E2E™ support forums are an engineer's go-to source for fast, verified answers and design help — straight
from the experts. Search existing answers or ask your own question to get the quick design help you need.
Linked content is provided "AS IS" by the respective contributors. They do not constitute TI specifications and do
not necessarily reflect TI's views; see TI's Terms of Use.
11.4 Trademarks
TI E2E™ is a trademark of Texas Instruments.
WEBENCH® is a registered trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.5 Electrostatic Discharge Caution
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled
with appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may
be more susceptible to damage because very small parametric changes could cause the device not to meet its published
specifications.
11.6 Glossary
TI Glossary
This glossary lists and explains terms, acronyms, and definitions.
Copyright © 2020 Texas Instruments Incorporated
Submit Document Feedback
29
Product Folder Links: TPS62912 TPS62913
TPS62912, TPS62913
SLVSFP4 – AUGUST 2020
www.ti.com
12 Mechanical, Packaging, and Orderable Information
The following pages include mechanical, packaging, and orderable information. This information is the most
current data available for the designated devices. This data is subject to change without notice and revision of
this document. For browser-based versions of this data sheet, refer to the left-hand navigation.
Copyright © 2020 Texas Instruments Incorporated
30
Submit Document Feedback
Product Folder Links: TPS62912 TPS62913
PACKAGE OUTLINE
VQFN-HR - 1 mm max height
PLASTIC QUAD FLAT PACK-NO LEAD
RPU0010A
2.1
1.9
A
B
2.1
1.9
PIN 1 INDEX AREA
1.0
0.8
C
SEATING PLANE
0.08 C
0.05
0.00
PKG
0.55
0.35
0.9
0.7
3X
3X
(0.2) TYP
7X 0.5
3
1
4
1
PKG
0.25
6
0.25
0.15
6X
0.1
C A B
C
0.05
10
7
0.4
0.3
PIN 1 ID
4X
0.3
0.2
(45o X 0.1)
4X
0.1
C A B
C
1.5
0.05
4224937 /A 04/2019
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
www.ti.com
EXAMPLE BOARD LAYOUT
VQFN-HR - 1 mm max height
PLASTIC QUAD FLAT PACK-NO LEAD
RPU0010A
(1.5)
PKG
4X (0.25)
7
7X (0.5)
10
4X (0.55)
(R0.05)
(0.25)
6
1
3
PKG
(1.675)
(1)
4
6X (0.2)
3X
(0.7)
3X (0.65)
3X (1)
3X
(0.875)
LAND PATTERN EXAMPLE
EXPOSED METAL SHOWN
SCALE: 25X
0.05 MIN
ALL AROUND
0.05 MAX
ALL AROUND
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
EXPOSED
METAL
EXPOSED
METAL UNDER
SOLDER MASK
METAL
NON- SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
NOT TO SCALE
4224937 /A 04/2019
NOTES: (continued)
3. For more information, see Texas Instruments literature number SLUA271 (www.ti.com/lit/slua271).
4. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
VQFN-HR - 1 mm max height
PLASTIC QUAD FLAT PACK-NO LEAD
RPU0010A
(1.5)
PKG
4X (0.25)
7
7X (0.5)
10
4X (0.55)
(R0.05)
(0.25)
6
1
3
PKG
(1.675)
(1)
4
6X (0.2)
3X (0.65)
3X
(0.7)
3X (1)
3X
(0.875)
SOLDER PASTE EXAMPLE
BASED ON 0.100 mm THICK STENCIL
SCALE: 25X
4224937 /A 04/2019
NOTES: (continued)
5.
Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations.
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TPS62912RPUR
TPS62913RPUR
XPS62912RPUR
PREVIEW VQFN-HR
PREVIEW VQFN-HR
RPU
RPU
RPU
10
10
10
3000
3000
3000
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
-40 to 150
-40 to 150
-40 to 150
ACTIVE
VQFN-HR
XPS62913RPUR
ACTIVE
VQFN-HR
RPU
10
3000
TBD
Call TI
Call TI
-40 to 150
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2020
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE AND DISCLAIMER
TI PROVIDES TECHNICAL AND RELIABILITY DATA (INCLUDING DATASHEETS), DESIGN RESOURCES (INCLUDING REFERENCE
DESIGNS), APPLICATION OR OTHER DESIGN ADVICE, WEB TOOLS, SAFETY INFORMATION, AND OTHER RESOURCES “AS IS”
AND WITH ALL FAULTS, AND DISCLAIMS ALL WARRANTIES, EXPRESS AND IMPLIED, INCLUDING WITHOUT LIMITATION ANY
IMPLIED WARRANTIES OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE OR NON-INFRINGEMENT OF THIRD
PARTY INTELLECTUAL PROPERTY RIGHTS.
These resources are intended for skilled developers designing with TI products. You are solely responsible for (1) selecting the appropriate
TI products for your application, (2) designing, validating and testing your application, and (3) ensuring your application meets applicable
standards, and any other safety, security, or other requirements. These resources are subject to change without notice. TI grants you
permission to use these resources only for development of an application that uses the TI products described in the resource. Other
reproduction and display of these resources is prohibited. No license is granted to any other TI intellectual property right or to any third
party intellectual property right. TI disclaims responsibility for, and you will fully indemnify TI and its representatives against, any claims,
damages, costs, losses, and liabilities arising out of your use of these resources.
TI’s products are provided subject to TI’s Terms of Sale (www.ti.com/legal/termsofsale.html) or other applicable terms available either on
ti.com or provided in conjunction with such TI products. TI’s provision of these resources does not expand or otherwise alter TI’s applicable
warranties or warranty disclaimers for TI products.
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2020, Texas Instruments Incorporated
相关型号:
TPS62912RPUR
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation
TI
TPS62913
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation
TI
TPS62913RPUR
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation
TI
TPS6291X
TPS6291x 3-V to 17-V, 2-A/3-A Low Noise and Low Ripple Buck Converter with Integrated Ferrite Bead Filter Compensation
TI
©2020 ICPDF网 联系我们和版权申明