TPS65231DCAR [TI]
POWER MANAGEMENT IC FOR DIGITAL SET TOP BOXES; 电源管理IC，用于数字机顶盒
| 型号： | TPS65231DCAR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | POWER MANAGEMENT IC FOR DIGITAL SET TOP BOXES |
| 文件： | 总26页 (文件大小：916K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
POWER MANAGEMENT IC FOR DIGITAL SET TOP BOXES
1
FEATURES
•
•
•
•
Supply Voltage Supervisor Circuit with Two
Monitor Inputs and Open Drain Output
Parallel I/O or I2C Control with User Selectable
Address
•
Wide Input Supply Voltage Range
(10.8 V - 22 V)
•
One Adjustable PWM Buck Controller
Advanced Fault Detection and Output Voltage
Adjustment Options in I2C Mode
–
–
–
–
–
10.8-V - 22-V Input Voltage Range
3.3-V - 6.1-V Output Voltage Range
500kHz switching frequency
Type III Compensation
Pull-Up Current Sources on Buck Enable Pins
for Accurate Start-Up Timing Control with
Preset Default
Programmable Current Limit
•
•
Over Current Protection on All Rails
•
Two Adjustable Step-Down Converter with
Integrated Switching FETs:
Thermal Shutdown to Protect Device During
Excessive Power Dissipation
–
–
–
–
–
–
4.75-V - 5.5-V Input
•
Thermally Enhanced Package for Efficient
Heat Management (48-pin HTSSOP)
0.9-V-3.3-V Output Voltage Range
3-A Output Current
APPLICATIONS
1-MHz Switching Frequency
Voltage Scaling Option
Type III Compensation
•
•
•
•
•
Digital Set Top Boxes
xDSL & Cable Modems
DVD Players
Home Gateway and Access Point Networks
Wireless Routers
•
Two 100-mΩ, 0.5-A (TPS65230) 1-A (TPS65231)
USB Switches with Over Current Protection
and Open-Drain Fault Pin
•
•
Early Supply Failure Flag (Open Drain Output)
is Set when Input Voltage Drops Below 9.3 V
Early Temperature Warning Flag (Open Drain
Output) is Set if Temperature Approaches
Shut-Down Threshold
DESCRIPTION/ORDERING INFORMATION
The TPS652x provides one PWM buck controller, two adjustable, synchronous buck regulators, two independent
USB power switches and a supply voltage supervisor (SVS) to provide main power functions for satellite set top
boxes, xDSL and cable modem applications operating off a single 12- to 22-V supply.
The SMPS have integrated switching FETs for optimized power efficiency and reduced external component
count. Each USB switch provides up to 0.5-A (TPS65230) or 1-A (TPS65231) of current as required by
downstream USB devices. All power blocks have thermal and over current/short circuit protection.
The SVS provides two inputs for monitoring positive supply rails. The active-low open-drain output remains low
for at least 180 ms after all supply rails rise above their rising edge threshold. Threshold value for VMON1 input
is set for monitoring a 3.3-V rail without the need for additional external components. Threshold for VMON2 input
is set to 0.8 V and requires resistor dividers on the input to monitor any positive voltage in the system. The
nBOR/nHOT open-drain output is pulled low if the input supply drops below 9.3 V or the chip temperature
approaches the thermal shutdown limit. This allows the system processor to save critical data and shut down
gracefully before the supply fails.
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of Texas
Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
PRODUCTION DATA information is current as of publication date.
Copyright © 2009, Texas Instruments Incorporated
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
The TPS65230 and TPS65231 can be controlled either through parallel I/Os or through I2C interface. When the
pull-up resistor on the USBFLAG2/nINT pin is connected to a 3.3-V or lower supply the I2C interface is disabled
and the device is controlled through parallel I/O pins only. With the pull-up resistor connected to 6 V the I2C
interface is enabled and the device is controlled by writing to the control registers. Any fault or abnormal
operating condition is flagged by the interrupt pin. The interrupt is cleared by reading the status register via the
I2C interface.
FUNCTIONAL BLOCK DIAGRAM
1 2V DC Sup ply
Op tion al
VINB and VINBQ pins must be t ied
t ogthe ron PC board
6V I2C MODE
3.3V UC MODE
1 2V
INT
HDRV
BST1
PH1
to uC or DSP
VNI
Vou t BUC K1
EN_BCK1
EN_BCK2
f ro m e na ble log ic
f ro m e na ble log ic
f ro m e na ble log ic
BUCK1
LDRV
EN_BCK3
FB1
CM P1
ENUSB1 /SCL
fro m uC o r DSP
fro m uC o r DSP
BST2
PH2a
PH2b
FB2
EENUSB2/SDA
I2C
REF
VNI B2
Vou t BUCK2
BUCK2
TRIM
TSD
OSC
CM P2
UVLO
V3p3
BST3
PH3a
PH3b
FB3
VNI B3
INTERNAL
VO LT AGE RAILS
VLSD
Vou t BUCK3
BUCK3
nRST
CM P3
VREF1
VREF2
t o u C or DSP
VM ON1
VM ON2
V3p3
RESET GENERATOR
Fr om 3. 3v s up py
USBF LG1/CTRL
USBO UT 1
To/f rom u C o r DSP
f ro m pos mo nit or Sup ply
USB1
I2C_ADD
To USB p ort
V3p3
USBF LG2/nINT
USBO UT 2
To/f rom u C o r DSP
USB2
To USB p ort
ORDERING INFORMATION(1)
TA
PACKAGE(2)
ORDERABLE PART NUMBER
TPS65230A2DCAR
TOP-SIDE MARKING
TPS65230
0°C to 85°C
48-pin (HTSSOP) - DCA
Reel of 2000
TPS65231A2DCAR
TPS65231
(1) For the most current package and ordering information, see the Package Option Addendum at the end of this document, or see the TI
web site at www.ti.com.
(2) Package drawings, thermal data, and symbolization are available at www.ti.com/packaging.
2
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
TERMINAL FUNCTIONS
NAME
NO.
1
I/O
DESCRIPTION
BG
I
I
I
I
I
I
I
Reference filter pin
VINBQ
V6V
2
Reference supply for BUCK2 and BUCK3
Filter pin for internal voltage regulator (6 V)
Input supply for BUCK1 and support circuitry
Feedback pin (BUCK2)
3
VIN
4
FB2
5
CMP2
6
Regulator compensation (BUCK2)
Enable pin for BUCK2, active high
Power ground BUCK2
EN_BCK2
PGND2
PH2
7
8, 9
10, 11
12, 13
14
O
I
Switching pin (BUCK2)
VINB2
Input supply for BUCK2 (must be tied to VINB3, VINBQ)
Bootstrap input (BUCK2)
BST2
DGND
15
Digital ground. All grounds should be joined together.
Low-side gate drive output (PWM controller)
High-side gate drive output (PWM controller)
Switching pin (BUCK1)
LDRV
16
O
O
O
I
HDRV
17
PH1
18
BST1
19
Bootstrap input (BUCK1)
EN_BCK1
CMP1
20
I
Enable pin for BUCK1, active high
Regulator compensation (PWM controller)
Feedback pin (PWM controller)
21
I
FB1
22
I
SS
23
I
External capacitor for soft start
TRIP
24
I
BUCK1 over current trip point set-up
Filter pin for internal voltage regulator (3.3 V)
Analog ground
V3P3
25
I
AGND
26
nRST
27
O
Reset output (open drain), active low
Enable pin for USB switch 1, active high / Clock input (I2C enabled).
Enable pin for USB switch 2, active high / Data input (I2C enabled)
USB2 fault flag / Interrupt pin
EN_USB1/SCL
EN_USB2/SDA
USBFLAG2/nINT
FB3
28
I
29
I
30
I/O
31
I
I
I
Feedback pin (BUCK3)
CMP3
32
Regulator compensation (BUCK3)
Enable pin for BUCK3, active high
Power ground BUCK3
EN_BCK3
PGND3
PH3
33
34, 35
36, 37
38, 39
40
O
I
Switching pin (BUCK3)
VINB3
Input supply for BUCK3 (must be tied to VINB2, VINBQ)
Bootstrap input (BUCK3)
BST3
I
USBOUT1
VINU
41
O
I
USB switch output (channel1)
42
Input supply for USB switches
USBOUT2
43
O
USB switch output (channel2)
USB1 fault flag, active low, open drain / Voltage control pin for BUCK2
(I2C enabled)
USBFLG1/VCTRL
44
I/O
nBOR/nHOT
VMON1
45
46
47
48
I/O
Brownout and hot warning, active low, open drain
Voltage monitor input (3.3 V rail)
I
I
I
VMON2
Voltage monitor input (positive reference)
If grounded, I2C address is 48h. Tied to V3P3 I2C address is 49.
I2C_ADD
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
3
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
DCA HTSSOP PACKAGE
(TOP VIEW)
BG
VINBQ
V6V
1
48
47
46
45
44
43
42
41
40
39
38
37
36
35
34
33
32
31
30
29
28
27
26
25
I2C_ADD
VMON2
2
3
VMON1
VIN
4
nBOR/nHOT
USBFLG1/VCTRL
USBOUT2
VINU
FB2
5
CMP2
EN_BCK2
PGND2
PGND2
PH2
6
7
8
USBOUT1
BST3
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
VINB3
PH2
VINB3
VINB2
VINB2
BST2
DGND
LDRV
HDRV
PH1
PH3
PH3
PGND3
PGND3
EN_BCK3
CMP3
FB3
BST1
EN_BCK1
CMP1
FB1
USBFLG2/nINT
EN_USB2/SDA
EN_USB1/SCL
nRST
SS
AGND
TRIP
V3P3
ABSOLUTE MAXIMUM RATINGS(1)(2)
over operating free-air temperature range (unless otherwise noted)
Input voltage range at VIN
–0.3 to 25
–0.3 to 7.0
–0.3 to 7.0
V
V
V
Input voltage range at VINB, VINBQ, VINU
Voltage range at INT
Voltage range at EN_BCK1, EN_BCK2, EN_BCK3, EN_USB1/SCL, EN_USB2/SDA,
nRST, USBFLG1/VCTRL2, USBFLG2/VCTRL3
–0.3 to 3.6
V
Voltage on HDRV, BST1
–0.3 to 31
–0.3 to 24
–0.3 to 3.6
–0.3 to 7.0
–0.3 to 15V
–0.3 to 3.6
3.8
V
V
V
V
V
V
A
Voltage on PH1
Voltage on FB1, CMP1, FB2, CMP2, FB3, CMP3
Voltage on PH2, PH3, LDRV
Voltage on BST2, BST3
Voltage on VMON1, VMON2, VMON3
Output Current BUCK2, BUCK3
Peak output current
Internally limited
2 k
Human body model (HBM)
ESD rating
V
Charged device model (CDM)
500
θJA
Thermal Resistance – Junction to ambient(3)
Continuous total power dissipation 55°C(3) no thermal warning
Operating virtual junction temperature range
Operating ambient temperature range
25
°C/W
W
2.6
TJ
0 to 150
0 to 85
°C
TA
°C
TSTG
Storage temperature range
–65 to 150
°C
(1) Stresses beyond those listed under "absolute maximum ratings" may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under "recommended operating
conditions" is not implied. Exposure to absolute–maximum–rated conditions for extended periods may affect device reliability.
(2) All voltage values are with respect to network ground terminal.
(3) Using JEDEC 51-5 (High K) board. This is based on standard 48DCA package, 4 layers, top/bottom layer: 2 oz Cu, inner layer: 1 oz Cu.
Board size: 114.3 x 76.2 mm (4.5 x 3 inches), board thickness: 1.6 mm (0.0629 inch).
4
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
RECOMMENDED OPERATING CONDITIONS
over operating free-air temperature range (unless otherwise noted)
MIN
10.8
4.75
4.75
NOM
MAX
22
UNIT
V
Input voltage range at VIN
Input voltage range at VINU
Input voltage range at VINB
12
5.5
6.1
V
Voltage range, EN_BCK1, EN_BCK2, EN_BCK3, EN_USB1/SCL, EN_USB2/SDA,
nRST, USBFLG1/VCTRL2, USBFLG2/VCTRL3 pins
3.3
V
Input voltage, nRST pin
3.3
6.6
3.3
50
V
V
Voltage range, INT pin (I2C disabled)
Voltage range, INT pin (I2C enabled)
Ambient operating temperature
5.4
V
TA
°C
ELECTRICAL CHARACTERISTICS
VIN = 12 V ±5%, VINB2, VINB3 = 5 V ±5%, VINU = 5 V ±5% TJ = 0°C to 150°C, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
10.8
9.3
TYP
MAX UNIT
INPUT VOLTAGE
VIN
Input supply voltage
12
22
V
V
VIN rising
10.8
VBOR
Brown Out Reset threshold
VIN falling
VIN rising
10.8
4.75
4.4
UVLO VIN
UVLO VINB
UVLO VINU
UVLO threshold – VIN (main supply)
V
V
V
VIN falling
VINB rising
VINB falling
VINU rising
VINU falling
4.7
UVLO threshold – VINB
(BUCK2/BUCK3 supply)
4.25
3.8
UVLO threshold – VINU (USB supply)
INPUT CURRENT
All regulators/USB switches
disabled
ICCQ
Input supply current
4
mA
LOGIC INPUT LEVEL (SCL, SDA, INT, VCTRL2, VCTRL3)
VIH
Input high level
1.2
4
V
V
V
VIL
Input low level
I2C disable voltage (INT)
0.4
VI2C_disable
BUCK ENABLE INPUTS (EN_BCK1,2,3)
VEN
VENHYS
IPULLUP
RD
Enable threshold
Enable voltage hysteresis
Pull-up current
1.2
100
6
V
mV
uA
kΩ
ms
tEN = 0.2 ms/nF
Power-up
Discharge resistor
1
tD
Discharge time
5
4.8
0.3
I2C ENABLE THRESHOLD (INT pin)
I2C enabled if pull-up resistor
is connected to a value
above threshold
VINTTH
I2C enable threshold
V
V
LOGIC OUTPUT LEVEL(SDA, INT, nRST, USBFLG1, USBFLG2 )
OL Output low level
PWM CONTROLLER (BUCK1)
IOUT = 3 mA through pull-up
0.4
6.1
VOUT
PG
Output voltage range(1)
3.3
V
Power good threshold
VOUT rising
95
%
(1) Output voltage range is limited by the minimum and maximum duty cycle. VOUT(min) ~ d(min) x VINPUT and VOUT(max) ~ d(max) x
VINPUT
.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
5
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VIN = 12 V ±5%, VINB2, VINB3 = 5 V ±5%, VINU = 5 V ±5% TJ = 0°C to 150°C, unless otherwise noted.
PARAMETER
Under voltage detect
Feedback voltage
TEST CONDITIONS
VOUT falling
MIN
TYP
75
MAX UNIT
UVD
VFB
%
–2%
0.804
2%
V
LDRV
HDRV
High and low side drive voltage
No load
6
V
R_ONLDRV
R_OFFLDRV
R_ONHDRV
R_OFFHDRV
d
Low side ON resistance
Low side OFF resistance
High side ON resistance
High side OFF resistance
Duty cycle(2)
8
1
Ω
Ω
Ω
Ω
%
20
1
20
80
AMOD
Modulator gain
12
fSW
Switching frequency
500
kHz
Current source for setting OCP trip
point
ITRIP
TA = 25°C
10
µA
TCTRIP
RTRIP
COUT
L
Temperature coefficient of ITRIP
Current-limit setting resistor
Output capacitance
3700
ppm/°C
kW
80
22(3)
250
3.3
47
µF
Nominal Inductance
Recommended
4.7
µH
BUCK2
VOUT
PG
Output voltage range(4)
Power good threshold
Under voltage detect
Feedback voltage
0.9
V
%
VOUT rising
VOUT falling
95
75
UVD
VFB
%
– 2%
0.804
2%
V
IOUT
η
Output current
3000
mA
%
Efficiency
IO = 2 A, VOUT = 3.3V
VIN12V = 12 V
95
32
36
5
Low-side MOSFET On resistance
High-side MOSFET On resistance
Switch current limit
RDS(ON)
ILIMIT
mΩ
A
Current limit accuracy
–30
30
1
%
Line regulation - DC
ΔVOUT/ΔVINB
VINB = 4.75 V - 6.1 V,
IOUT = 1 A
VLINEREG
VLOADREG
VOUTTOL
%
Load regulation - DC
ΔVOUT/ΔIOUT
IOUT = 10 – 90% IOUT,MAX
0.5
%/A
Feedback resistor tolerance
not included
DC set tolerance
–2
15
2
%
%
d
Duty cycle(5)
85
AMOD
fSW
Modulator gain
5
1
Switching frequency
Output capacitance
Capacitor ESR
MHz
µF
COUT
ESR
L
10(3)
47
50
mW
µH
Nominal inductance
2.2
BUCK3
VOUT
PG
Output voltage range(4)
Power good threshold
Under voltage detect
0.9
3.3
V
%
%
VOUT rising
VOUT falling
95
75
UVD
(2) Performance outside these limits is not guaranteed.
(3) Absolute value. User should make allowances for tolerance and variations due to component selection.
(4) Output voltage range is limited by the minimum and maximum duty cycle. VOUT(min) ~ d(min) x VINPUT and VOUT(max) ~ d(max) x
VINPUT
(5) Performance outside these limits is not guaranteed.
.
6
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
ELECTRICAL CHARACTERISTICS (continued)
VIN = 12 V ±5%, VINB2, VINB3 = 5 V ±5%, VINU = 5 V ±5% TJ = 0°C to 150°C, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
50
MAX UNIT
PG glitch rejection
µs
VFB
IOUT
η
Feedback voltage
–2%
0.804
2%
3
V
A
Output current
Efficiency
IO = 2 A, VOUT = 1.2 V
VIN12V = 12 V
86
32
36
5
%
Low-side MOSFET On resistance
High-side MOSFET On resistance
Switch current limit
Current limit accuracy
RDS(ON)
ILIMIT
mΩ
A
–30
30
1
%
Line regulation - DC
ΔVOUT/ΔVINB
VINB = 4.75 V - 6.1 V,
IOUT = 1000 mA
VLINEREG
VLOADREG
VOUTTOL
%
Load regulation - DC
ΔVOUT/ΔIOUT
IOUT = 10 – 90% IOUT,MAX
0.5
%/A
Feedback resistor tolerance
not included
DC Set Tolerance
–2
15
2
%
%
d
Duty cycle(5)
85
AMOD
fSW
COUT
ESR
L
Modulator gain
5
1
Switching frequency
Output capacitance
Capacitor ESR
MHz
µF
10
50
mW
µH
Nominal inductance
2.2
SOFT START (BUCK1, 2, and 3)
ISS
Soft start current source
2
0.8
3.3
2.5
500
µA
V
VSS, MAX
CSS
Soft start ramp voltage
Soft start capacitor
Deglitch time
Ramp end
tSS = 0.4 ms/nF
2
3
5
nF
ms
µS
SSDONE_BK
SSDONE_DCH
SS discharge time
SUPPLY VOLTAGE SUPERVISOR
Supply rising
Supply falling
Hysteresis
3.2
Threshold voltage
(VMON1)
VMON1
V
.05
850
750
20
Supply rising
Supply falling
Hysteresis
Threshold voltage
(VMON2)
VMON2
mV
tdeglitch
VOL
Deglitch time (both edges)
192
µs
V
Reset pin output-low voltage
Minimum reset period
Isink = 3.2 mA
0.4
tRP
180
100
ms
USB POWER SWITCHES
RDS(on) On resistance
mΩ
VINU = 5.5 V, CL = 120 mF,
VOUT 10% to 90%.
tr
Rise time output
1
ms
ton
toff
Turn-on time
CL = 100 µF, rL = 10 Ω
CL = 100 µF, rL = 10 Ω
TPS65230
3
10
1
ms
ms
Turn-off time
Over Current limit
Output shorted to ground
Over current deglitch
0.6
1.2
4
0.8
1.6
8
IOC
A
TPS65231
2
OC deglitch
15
ms
THERMAL SHUTDOWN
Thot
Thermal warning
120
°C
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
7
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
ELECTRICAL CHARACTERISTICS (continued)
VIN = 12 V ±5%, VINB2, VINB3 = 5 V ±5%, VINU = 5 V ±5% TJ = 0°C to 150°C, unless otherwise noted.
PARAMETER
TEST CONDITIONS
MIN
TYP
160
20
MAX UNIT
Ttrip
Thermal S/D trip point
Thermal S/D hysteresis
°C
°C
Thyst
SUPPLY VOLTAGE SUPERVISOR (SVS)
The supply voltage supervisor monitors two inputs, VMON1 and VMON2, and generates a reset pulse of at least
180-ms length when one or more supplies fall below their respective thresholds. All inputs are deglitched for very
short dips on the supplies. The reference values for VMON1 is specified for monitoring a 3.3-V rail without the
need of external components. The reference for VMON2 is set to monitor arbitrary supply voltages and require
resistor dividers at the inputs.
Please note that the reset signal generated by the SVS is for external use only and has no impact on the power
rails or USB switches of the TPS65230 and TPS65231.
Hysteresis
nRST
Time
min 180ms
Figure 1. Supply Voltage Supervisor Reset Generation
USB POWER SWITCHES
The TPS65230 and TPS65231 provide two power-distribution switches intended for applications where heavy
capacitive loads and short-circuits are likely to be encountered. Gate drive is provided by an internal regulator.
Each switch is controlled by a logic enable input or, when I2C interface is enabled, switches are controlled
through EN_USBx bits of the ENABLE register.
When the output load exceeds the current-limit threshold or a short is present, the device limits the output current
to a safe level by switching into a constant-current mode, pulling the USBFAULTx output low. When continuous
heavy overloads and short-circuits increase the power dissipation in the switch, causing the junction temperature
to rise, a thermal protection circuit shuts off the switches when a thermal warning condition occurs to prevent
damage. Recovery from a thermal warning is automatic once the device has cooled sufficiently. Internal circuitry
ensures that the switch remains off until valid input voltage is present.
8
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
POWER-UP SEQUENCING
ON/OFF control and power sequencing of the three buck regulators is controlled through EN_BCK1, EN_BCK2,
and EN_BCK3 enable pins. Each pin is internally connected to a 6-µA constant-current source and monitored by
a comparator with Schmitt trigger input with defined threshold. Connecting EN_BCKn pin to ground disables
BUCKn and connecting EN_BCKn to V3P3 will enable the respective buck without delay. If more than one buck
enable pin is connected to V3P3 the default startup sequence is BUCK1, BUCK2, BUCK3 and the minimum
startup delay between rails is the soft-start time (typical 1.5 ms) plus 1 ms.
To create a startup-sequence different from the default, capacitors are connected between the EN_BUCKn pins
and ground. At power-up the capacitors are first discharged and then charged to V3P3 level by internal current
sources (6 µA typical) creating a constant-slope voltage ramp. A regulator is enabled when its EN pin voltage
crosses the enable threshold (typical 1.2 V). A delay of 0.2 ms is generated for each 1-nF of capacitance
connected to the enable pin. If two enable pins are pulled high while the third regulator is starting up, the default
sequence will be applied to enable the remaining two regulators. To override default power-up sequence it is
recommended that delay times differ by more than the soft-start time (typical 1.3 ms) plus 1 ms.
In I2C mode regulators can also be enabled by setting their respective EN bits in the ENABLE register. The same
startup-time limitations and arbitration rules apply in I2C mode as described above.
V3p3
V3p3
Delay time = 0.2ms/nF
(1)
(2)
6uA
1.2V
EN_BCKx
Enable
Threshold
BUCK ENABLE
Time
BUCK A
Enable
BUCK C
Enable
BUCK B
Enable
(1) Connect EN_BCKx pin to V3P3 to follow the default power-up sequence or
(2) Connect a capacitor from EN_BCKx to GND to generate a custom power-up sequence.
Figure 2. Customizing the Power-Up Sequence
OVER CURRENT PROTECTION
Over current protection (OCP) for BUCK1 is achieved by comparing the drain-to-source voltage of the low-side
MOSFET to a set-point voltage, which is defined by both the internal current source, ITRIP, and the external
resistor connected between the TRIP pin and ground. Over current threshold is calculated as Equation 1.
RTRIP · ITRIP
10 · RDS(ON)
ILIM
=
(1)
ITRIP has a typical value of 10 µA at 25°C and a temperature coefficient of 3700 ppm/°C to compensate the
temperature dependency of the MOS RDS(ON). The TPS65230 and TPS65231 support cycle-by-cycle over current
limiting control which means that the controller compares the drain-to-source voltage of the low-side FET to the
set-point voltage once per switching cycle and blanks out the next switching cycle if an over-current condition is
detected. If in the following cycle over current condition is detected again, the controller blanks out 2, then 4, 8,
and up to 16 cycles before turning on the high-side driver again. In an over current condition the current to the
load exceeds the current to the output capacitor thus the output voltage will drop, and eventually cross the under
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
9
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
voltage protection threshold and shut down the BUCK controller. Buck 2 and 3 show a similar mode of operation.
All converters operate in hiccup mode: Once an over-current is sensed, the controller shuts off the converter for
a given time and then tries to start again. If the overload has been removed, the converter will ramp up and
operate normally. If this is not the case the converter will see another over-current event and shuts-down again
repeating the cycle (hiccup) until the failure is cleared.
SOFT START
Soft start (SS) for all three BUCKs is controlled by a single capacitor connected to the SS pin and an internal
current source. When one of the BUCKs is enabled, the SS capacitor is pre-charged to the output voltage
divided by the feed-back ratio before the internal SS current source starts charging the external capacitor. The
output voltage of the BUCK ramps up as the SS pin voltage increased from its pre-charged value to 0.8 V. The
soft start time is calculated from the SS supply current (ISS) and the capacitor value and has a typical value of
0.4 ms/nF or 1.3 ms for a 3.3-nF capacitor connected to the SS pin. Before the next rail is enabled, the SS cap is
discharged and the SS cycle starts over again.
BROWNOUT MONITOR (BOR)
The TPS65230 and TPS65231 monitor the input supply and issues a warning if the input voltage drops below the
BOR threshold of 9.3 V. The nBOR/nHOT pin is pulled low to alarm the host processor of the brown-out
condition. nBOR is released after the supply voltage has risen above 10.8 V. nBOR/nHOT pin is also pulled low
when the chip temperature rises above the HOT threshold and is released when the chip has cooled off. The
purpose of the nBOR/nHOT function is to give the host processor time to finish operations and store data before
the system shuts down. Both events, BOR and HOT, are individually flagged in the STATUS1 register. Note that
unlike the INT output pin, reading the STATUSx registers has no effect on the state of the nBOR/nHOT pin in I2C
mode. nBOR/nHOT depends only of the input voltage and temperature condition.
10
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
VIN (12 V)
10.8V
9.3V
4.8V
nBOR/nHOT
Under Voltage Lock Out(UVLO)
disables all output rails and USB
UVLO (internal signal )
Time
Available time for controlled
shutdown of System
160C
Thermal Shutdown (TSD)
130C
Thermal warning (HOT)
NOTE: All rails are shutdown
when temperature exceeds TSD
Temperature
threshold. System recovers
automatcally when IC has cooled
down to TSD- TSD
.
HYSTERESIS
nBOR/nHOT
Available time for controlled
shutdown of System
Figure 3. Brownout Monitoring
UNDER VOLTAGE LOCKOUT (UVLO)
TPS65230 and TPS65231 monitors VIN, VINB, and VINU pin voltages and will disable one or more power paths
depending on the current use condition:
•
•
•
•
If VIN drops below 9.3 V, both USB power paths are disabled and the nBOR/nHOT output pin is pulled low.
If VIN drops below 4.7 V, BUCK1, 2, and 3 are disabled.
If VINB drops below 4.25 V and either BUCK2 or BUCK3 are enabled, all three output rails are disabled.
If VINU drops below 3.9V and either USB1 or USB2 are enabled, both USB switches are disabled.
UVLO state is not latched and the system recovers as soon as the input voltage rises above its respective
threshold. All three BUCK_ENx pins are discharged and remain discharged during UVLO to ensure proper power
sequencing when the system recovers.
In I2C mode the EN_BUCKx and EN_USBx bits of the ENABLE register are reset in an UVLO event and interrupt
is issued. To re-enable the output supplies, the respective EN_BUCKx bits have to be set through the I2C
interface or the BUCK_ENx pins have to be pulled high. To re-enable the USB power switches in I2C mode, the
EN_USBx bits of the ENABLE register have to be set through the I2C interface.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
11
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
THERMAL SHUTDOWN (TSD)
TPS65230x monitors junction temperature and will disable all power paths (BUCK1-3, USB1 and 2) if junction
temperature rises above the specified trip point. nBOR/nHOT pin will be pulled low if the temperature approaches
the TSD trip point within 40°C. In I2C mode the device will also issue an interrupt and set the HOT bit in
STATUS1 register. The system recovers as soon as the temperature falls below the falling-edge trip
temperature. All three BUCK_ENx pins are discharged and remain discharged during TSD to ensure proper
power sequencing when the system recovers.
In I2C mode the EN_BUCKx and EN_USBx bits of the ENABLE register are reset in a TSD event and interrupt is
issued. To re-enable the output supplies the respective EN_BUCKx bits have to be set through the I2C interface
or the BUCK_ENx pins have to be pulled high. To re-enable the USB power switches in I2C mode, the EN_USBx
bits of the ENABLE register have to be set through the I2C interface.
LOOP COMPENSATION
All three BUCKs are voltage mode converters designed to be stable with ceramic capacitors. Refer to
Component Selection Procedure section for calculating feedback components.
3.3-V REGULATOR
The TPS6532x has a built-in 3.3-V regulator for powering internal circuitry. The 3.3-V rail can also be used for
enabling the BUCK regulators and/or the USB switches, but is not intended for supplying any other external
circuitry. For light loading of this rail during stand-by operation consult TI FAE.
6-V REGULATOR
The TPS6532x has a built-in 6-V regulator for powering internal circuitry. The 6-V rail can also be used for
enabling I2C functionality by connecting the pull-up resistor on the USBFLG2/nINT pin to V6V but is not intended
for supplying any other external circuitry. For light loading of this rail during stand-by operation consult TI FAE.
USER SELECTABLE SERIAL INTERFACE
TPS65230 and TPS65231 feature an I2C slave interface which can be enabled or disabled by the user and offers
advanced control and diagnostic features. I2C control is enabled when the pull-up resistor on the USBFLG2/nINT
pin is connected to a supply voltage > 4.5 V and is disabled otherwise. When disabled, BUCK1, 2, 3, and USB1,
2 are controlled through their respective enable pins. When the I2C interface is enabled, USB1 and USB2 are
controlled through the serial interface and BUCK1, 2, and 3 are controlled either through the serial interface or
their respective enable pins. In addition, the USBFLG1/VCTRL pin is reconfigured when I2C is enabled to offer
output voltage control for BUCK2 and BUCK3.
I2C operation offers brownout and thermal shutdown warning, thermal shut down flag, power-good and
under-voltage indicator for BUCK1-3 and USB fault indicator for both USB switches. Whenever a fault is
detected, the associated status bit in the STATUS1 and 2 registers are set and the INT pin is pulled low.
Reading of the STATUS1 and 2 registers resets the flag bits and INT pin is released after all flags have been
reset. Note that in I2C mode the nINT pin is active high with voltage swing of > 3.3 V. To invert the signal and
shift the voltage level down to an I/O compatible level, connect the circuit shown in Figure 5 to the USBFL2/nINT
pin.
INT Dependent Device Pin Configuration
PIN NO.
30
DEVICE PIN
USBFLG2/nINT
EN_USB1/SCL
EN_USB2/SDA
USBFLG1/VCTRL
USBFLG2/INT CONNECTED TO V6V(1)
USBFLG2/INT CONNECTED TO 3.3V(1)
nINT
SCL (Clock)
Error flag for USB switch 2
28
Enable pin for USB switch 1
Enable pin for USB switch 2
Error flag for USB switch 1
29
SDA (Data)
44
Voltage control input for BUCK2 and 3
(1) Via pull-up resistor
12
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
I2C operation also offers output voltage adjustment options for BUCK2 and BUCK3. This is feature is useful to
reduce power dissipation in the system by lowering the supply voltages when the system is in idle state. Output
voltage can be scaled down by 5, 10 and 15% depending on the VBCKn[1:0] bit settings in the VADJUST
register. Settings are activated when the USBFLG1/VCTRL pin is pulled high and are deactivated when the pin is
pulled low. This allows for fast output voltage transition without involvement of the I2C interface. Alternatively the
settings can be activated by setting the the VCTRLx bits of the ENABLE register.
VBCK3[1:0]
00 – 0%
01 – 5%
VBUCK3
VBUCK2
VBUCK1
10 – 10%
11 – 15%
VBCK2[1:0]
00 – 0%
01 – 5%
10 – 10%
11 – 15%
VCTRL pin
or VCTRL bit
Time
Figure 4. BUCK2 and BUCK3 Output Voltages
V6V
3.3V
4.7K
10K
To uC
2222A
USBFLG2/nINT
47.5K
Figure 5. Circuit for Level-Shifting and Inverting nINT Signal
I2C BUS OPERATION
The TPS65230 hosts a slave I2C interface that supports data rates up to 400 kbit/s and auto-increment
addressing and is compliant to I2C standard 3.0.
Slave Address + R/nW
Sub Address
Data
Start
G3
G2
G1 G0
A2
A1
A0 R/nW ACK S7
S6
S5
S4
S3
S2
S1
S0
ACK D7
D6
D5
D4
D3
D2
D1
D0
ACK Stop
Figure 6. Subaddress in I2C Transmission
Start — Start condition
G(3:0) — Group ID: 1001
A(2:0) — Device address: 000
R/nW — Read/not write select bit
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
13
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
ACK — Acknowledge
S(7:0) — Subaddress: defined per register map
D(7:0) — Data: data to be loaded into the device
Stop — Stop condition
The I2C Bus is a communications link between a controller and a series of slave terminals. The link is established
using a two-wired bus consisting of a serial clock signal (SCL) and a serial data signal (SDA). The serial clock is
sourced from the controller in all cases where the serial data line is bi-directional for data communication
between the controller and the slave terminals. Each device has an open drain output to transmit data on the
serial data line. An external pull-up resistor must be placed on the serial data line to pull the drain output high
during data transmission.
Data transmission is initiated with a start bit from the controller as shown in Figure 7. The start condition is
recognized when the SDA line transitions from high to low during the high portion of the SCL signal. Upon
reception of a start bit, the device will receive serial data on the SDA input and check for valid address and
control information. If the appropriate group and address bits are set for the device, then the device will issue an
acknowledge pulse and prepare the receive subaddress data. Subaddress data is decoded and responded to as
per the Register Map section of this document. Data transmission is completed by either the reception of a stop
condition or the reception of the data word sent to the device. A stop condition is recognized as a low to high
transition of the SDA input during the high portion of the SCL signal. All other transitions of the SDA line must
occur during the low portion of the SCL signal. An acknowledge is issued after the reception of valid address,
sub-address and data words. The I2C interface will auto-sequence through register addresses, so that multiple
data words can be sent for a given I2C transmission. Reference Figure 7.
. . .
SDA
. . .
SCL
1
2
3
4
5
6
7
8
9
START CONDITION
ACKNOWLEDGE
STOP CONDITION
Figure 7. I2C Start / Stop / Acknowledge Protocol
t H
(S
T A)
t LO W
t r(
t F
S C L
t H
(S TA
)
t H
tH
t S(
t S
t S
(S TO )
(D
A
T
)
I
G H
D
AT
)
(S TA
)
S D A
t (B
U
F)
P
S
S
P
Figure 8. I2C Data Transmission Timing
14
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
DATA TRANSMISSION TIMING
VBUS = 3.6 V ±5%, TA = 25 °C, CL = 100 pF (unless otherwise noted)
PARAMETER
TEST CONDITIONS
SCL = 100 kHz
MIN
MAX UNIT
100
kHz
400
f(SCL)
t(BUF)
t(SP)
Serial clock frequency
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
SCL = 100 kHz
SCL = 400 kHz
4.7
1.3
Bus free time between stop and start condition
Tolerable spike width on bus
SCL low time
µs
50
ns
4.7
1.3
4
tLOW
µs
µs
ns
µs
µs
tHIGH
SCL high time
0.6
250
100
4.7
0.6
4
tS(DAT)
tS(STA)
tS(STO)
tH(DAT)
tH(STA)
tr(SCL)
tf(SCL)
tr(SDA)
tf(SDA)
SDA → SCL setup time
Start condition setup time
Stop condition setup time
SDA → SCL hold time
Start condition hold time
Rise time of SCL signal
Fall time of SCL signal
Rise time of SDA signal
Fall time of SDA signal
0.6
3.45
µs
0.9
4
µs
0.6
1000
ns
300
300
ns
300
1000
ns
300
300
ns
300
THERMAL MANAGEMENT AND SAFE OPERATING AREA
Total power dissipation inside TPS6523x is limited not to exceed the maximum allowable junction temperature of
150°C. The maximum allowable power dissipation is a function of the thermal resistance of the package (θJA)
and ambient temperature. θJA itself is highly dependent on board layout. The maximum allowable power inside
the IC for operation at maximum ambient temperature without exceeding the temperature warning flag using the
JEDEC High-K board is calculated as Equation 3.
DT = qJA · P
(2)
TMAX - Tambient
120°C - 55°C
25°C/W
PMAX
=
» 2.6 W
=
qJA
(3)
For different PCB layout arrangements the thermal resistance (θJA) will change as the following table shows.
BOARD TYPE
STACK-UP
θJA
1.5-oz Cu, 60% Cu coverage top layer, 80% Cu coverage bottom
layer, no airflow
8" x 10" FR4 PCB, four layers
29
0.5-oz 30%Cu coverage inner layers
1-oz Cu, 20% Cu coverage top layer, 90% Cu coverage bottom
layer, no airflow
8” x 10” FR4 PCB, two layers
44
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
15
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
A minimum of two layers of 1-oz Cu with 20% Cu coverage on the top and 90% coverage on the bottom and the
use of thermal vias to connect the thermal pad to the bottom layer is recommended. Note that the maximum
allowable power inside the device will depend on the board layout. For recommendations on board layout for
thermal management using TPS6523x consult your TI field application engineer.
In the example shown above the maximum allowable power dissipation for the IC has been calculated. This
figure includes all heat sources inside the device including the power dissipated in BUCK1, BUCK2, BUCK3,
USB switches, and all supporting circuitry. Power dissipated in BUCK1, USB switches (500 mA full load) , and all
supporting circuitry is approximately 0.4 W and almost independent of the application. Power dissipated in
BUCK2 and BUCK3 depends on the output voltage, output current, and efficiency of the switching converters.
The following examples of safe operating area assume 90% efficiency for BUCK2 and BUCK3, 3.3-V output from
BUCK3 and 1.2-V, 1.8-V, and 2.5-V output from BUCK2, respectively.
3.5
3.5
3.5
3
3
3
2.5
2.5
2.5
2
2
2
1.5
1.5
1.5
Safe Operating Area
Safe Operating Area
Safe Operating Area
1
1
1
0.5
0.5
0.5
0
0
0
0
0.5
1
1.5
2
2.5
3
3.5
0
0.5
1
1.5
2
2.5
3
3.5
0
0.5
1
1.5
2
2.5
3
3.5
Current from BUCK2 [A] @ 1.2V or less
Current from BUCK2 [A] @ 1.8V
Current from BUCK2 [A] @ 2.5V
For any voltage / current comination inside the shaded area, the dissipated power inside the chip is below the allowable
maximum. The examples assume Tambient < 60°C, h = 90% and qJA < 44°C/W.
Figure 9. Examples of Thermal Safe Operating Area for V(BUCK3) = 3.3 V and V(BUCK1) = 1.2 V, 1.8 V
and 2.5 V, Respectively
COMPONENT SELECTION PROCEDURE
The following example illustrates the design procedure for selecting external components for the three buck
converters. The example focuses on BUCK1 but the procedure can be directly applied to BUCK2 and 3 as well.
The design goal parameters are given in the table below. A list of symbol definitions is found at the end of this
section. For this example the schematic in Figure 10 will be used.
16
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
Figure 10. Sample Schematic for TPS6523x Showing Components Relevant to BUCK1
PARAMETER
TEST CONDITIONS
MIN
10.8
TYP
MAX
13.2
UNIT
V
VIN
Input supply voltage
Input voltage ripple
Output Voltage
Line regulation
12
VIN RIPPLE
VOUT
IOUT, BUCK1 = 6 A
60
mV
V
4.75
5
25
25
5.25
VIN = 10.8 V to 13.2 V
IOUT, BUCK1 = 0 A to 6 A
IOUT, BUCK1 = 6 A
mV
mV
mV
mV
A
Load regulation
Output ripple
VOUT RIPPLE
VTRANS
IOUT
50
6
Transient deviation
Output current
IOUT, BUCK1 = 2 A to 6 A
VIN = 10.8 V to 13.2 V
125
500
0
fSW
Switching frequency
kHz
INDUCTOR SELECTION
For BUCK1 the recommended inductor value is 4.7 µH and for BUCK2 and 3 it is 2.2 µH. These values will
provide a good balance between ripple current, efficiency, loop bandwidth and inductor cost. The inductor is
typically sized for < 30% peak-to-peak ripple current (IRIPPLE). Given this target ripple current, the required
inductor size is calculated by Equation 4.
VIN(MAX) - VOUT
0.3 · IOUT
VOUT
VIN(MAX)
1
¾
·
fSW
·
L =
(4)
Solving Equation 4 with VIN(MAX) = 13.2 V, an inductor value of 3.5 µH is obtained. A standard value of 4.7 µH is
selected, resulting in 1.25-A peak-to-peak ripple. The RMS current through the inductor is approximated by
Equation 5.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
17
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
2
2
2
(IOUT) +
2
1
12
1
12
IL(RMS)
=
¾
+
¾
(IL(avg)
(IRIPPLE
)
(IRIPPLE
)
) =
Ö
Ö
(5)
Using Equation 5, the maximum RMS current in the inductor is about 6.01 A.
OUTPUT CAPACITOR SELECTION
The selection of the output capacitor is typically driven by the output load transient response requirement. The
output capacitance (base) proposed is 2 x 22 µF (or 4 X 10 µF or 1 x 47 µF) ceramic, providing a good balance
between ripple, cost and performance. Extra caps added should be electrolyte or far from base cap to have
considerable amount of ESR and not to affect compensation.
Equation 6 and Equation 7 estimate the output capacitance required for a given output voltage transient
deviation.
2
ITRAN(MAX) · L
when VIN(MIN) < 2 · VOUT
COUT(MIN)
=
(VIN(MIN) - VOUT) · VTRAN
(6)
(7)
2
ITRAN(MAX) · L
when VIN(MIN) > 2 · VOUT
COUT(MIN)
=
VOUT · VTRAN
For this example, Equation 7 is used in calculating the minimum output capacitance.
Based on a 4-A load transient with a maximum 125-mV deviation (2.5% of set voltage), a minimum of 120-µF
output capacitance is required. We choose two 22-µF ceramic capacitors and two electrolytic 47 µF in parallel for
a total capacitance of 138 µF.
The output ripple is divided into two components. The first is the ripple generated by the inductor ripple current
flowing through the output capacitor’s capacitance, and the second is the voltage generated by the ripple current
flowing in the output capacitor’s ESR. The maximum allowable ESR is then determined by the maximum ripple
voltage and is approximated by Equation 8.
IRIPPLE
VRIPPLE(total)
-
(
)
VRIPPLE(total) - VRIPPLE(cap)
COUT · fSW
ESRMAX
=
=
IRIPPLE
IRIPPLE
(8)
Based only on the 138-µF of capacitance, 1.25-A ripple current, 500-kHz switching frequency and a design goal
of 50-mV ripple voltage (1% of set voltage), we calculate a capacitive ripple component of 18 mV and a
maximum ESR of 25 mΩ. The X5R ceramic capacitors selected provide significantly less than 25-mΩ of ESR.
PEAK CURRENT RATING OF THE INDUCTOR
With output capacitance known, it is now possible to calculate the charging current during start-up and determine
the minimum saturation current rating of the inductor. The start-up charging current is approximated by
Equation 9.
VOUT · COUT
ICHARGE
=
TSS
(9)
Using the TPS65230 and TPS65231’s recommended 1.3-ms soft-start time, COUT = 188 µF and VOUT = 5 V,
ICHARGE is found to be 720 mA. The peak current rating of the inductor is now found by Equation 10.
1
¾
IL(PEAK) = IOUT(MAX)
+
IRIPPLE + ICHARGE
2
(10)
For this example an inductor with a peak current rating of 7.3 A is required. Note however that the inductor will
need to withstand the current limit figure without a major reduction of its rated inductance.
INPUT CAPACITOR SELECTION
The input voltage ripple is divided between capacitance and ESR. For this design, VRIPPLE(cap) = 60 mV (0.5% of
supply) and VRIPPLE(ESR) = 30 mV (0.25% of supply). The minimum capacitance and maximum ESR are
estimated by Equation 11 and Equation 12.
18
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
ILOAD · VOUT
CIN(MIN)
=
VRIPPLE(cap) · VIN · fSW
(11)
(12)
VRIPPLE(ESR)
ESRMAX
=
1
¾
2
ILOAD
+
IRIPPLE
For this design, CIN > 8 µF and ESR < 4 mΩ. The RMS current in the output capacitors is estimated by
Equation 13.
2
2
1
12
VOUT · IOUT
VIN
· VOUT
)
VIN
IRMS(CIN) = IIN(RMS) - IIN(avg)
=
¾
((IOUT) + (IRIPPLE
)
¾
-
Ö
(13)
With VIN = VIN(MAX), the input capacitors must support a ripple current of 1.4-A RMS. It is important to check the
DC bias voltage de-rating curves to ensure the capacitors provide sufficient capacitance at the working voltage.
Typically a 10-µF capacitor per converter is used. These capacitors should be placed as close as possible to the
VINB2 and VINB3 pins (BUCK2 and BUCK3) and to the external MOSFET arrangement for BUCK1.
BOOTSTRAP CAPACITOR
To ensure proper charging of the high-side MOSFET gate, limit the ripple voltage on the bootstrap capacitor to
< 5% of the minimum gate drive voltage.
20 · QGS, HSD
VIN(MIN)
CBOOST
=
(14)
Based on the FDS6982 MOSFET with a maximum total gate charge of 26 nC, calculate a minimum of 80-nF of
capacitance. A standard value of 220 nF is selected for BUCK1 and 100 nF for BUCK2.
SHORT CIRCUIT PROTECTION (BUCK1 ONLY)
The TPS65230 and TPS65231 uses the forward drop across the low-side MOSFET during the OFF time to
measure the inductor current. The voltage drop across the low-side MOSFET is given by Equation 15.
VDS = IL(PEAK) · RDSON, LSD
(15)
When VIN = 10.8 V to 13.2 V, IPEAK = 7.4A for full load (6 A). Using the FDS6982 MOSFET with a RDSON,MAX at TJ
= 25°C of 20 mΩ we calculate the peak voltage drop to be 148 mV. Adding a 50% margin to include inductor
variations and overload margin, the drop voltage for tip is set at 210 mV. Solving Equation 1 for RTRIP and using
ITRIP = 10 µA:
RTRIP = RDS(ON) · ILIM · 106
(16)
We calculate a trip resistor value of 210 kΩ. Place a 1-nF capacitor parallel to R9. Please note that typical FET
RDS(ON) is specified at 10 mΩ. Since we used RDSON,MAX, for setting the current limit, the actual current flowing
through the inductor with a nominal FET can be higher than the peak current of 7.4 A before the current limit
kicks in. Make sure that the chosen inductor has the correct peak current capabilities.
SHORT CIRCUIT PROTECTION (BUCK2 AND 3 ONLY)
Current limits for BUCK2 and 3 are internally set to 5 A.
FEEDBACK LOOP DESIGN
For the TPS6523x, the switching frequency and nominal output filter combination have been chosen to be
0.5 MHz 4.7 µH/~40 µF for BUCK1 and 1 MHz 2.2 µH/~40 µF for BUCK2 and 3 respectively. These values were
seen as a good compromise between efficiency and small solution size. The bandwidth has been chosen to be
around 1/8th - 1/11th of the switching frequency to maximize transient response whilst retaining low noise
sensitivity. As indicated before it is required that the output capacitor is ceramic and further that the very low ESR
causes it’s associated zero to be at or above the bandwidth of the converter.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
19
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
The control loop for the TPS6523x has an internal mid- to high-frequency zero-pole pair to compensate the
resonant pole caused by the output L-C filter. The maximum phase boost occurs at the geometric mean of the
pole zero arrangement and therefore aimed to be equal to the desired bandwidth. The pole limits the gain at high
frequencies to reduce noise sensitivity and it is about 5 times higher than the zero located at ~45 kHz.
The COMP pin of the buck converters is the output of an integrator Used to get high DC accuracy. The integrator
also takes care of any offsets in the zero-pole pair amplifier and the summing comparator inside the device. Also
a feed-forward loop is added to the attenuator circuit.
Vout
R2
FB
Comp
Cz
Rc
Cc
R1
Croll
Figure 11. External Compensation Circuit
The procedure to set the integrator values is very simple (see Figure 11):
1. Set the feed-forward circuit making R2 = 20 kΩ, CZ= 1 nF.
2. Calculate R1 as per output voltage requirement. Select R25 between 10 kΩ and 100 kΩ. For this design
select 22.1 kΩ, 0.1% resistor for the upper side of all dividers. Next, R29 Is selected to produce the desired
output voltage when VFB = 0.8 V using Equation 17.
VFB · R25
R29 =
VOUT - VFB
(17)
VFB = 0.8 V and R25 = 22.1 kΩ for VOUT = 5.0 V, R25 = 4.209 kΩ. The closest value 4.22 kΩ.
3. Set the integrator values, RC = 20 kΩ, CC = 1 nF.
4. Make Croll = 100 pf to roll-off gain at high frequencies.
5. If VIN is ~20 - 24 V use 200 pF for Croll on DCDC1.
Other Components
A 1-µF ceramic capacitor should be connected as close as possible to the following pins:
•
•
•
•
BG (pin 1): Bandgap reference
VIN (pin 4): Bypass capacitor (higher values are acceptable)
V6V (pin 3): Internal 6 V supply
V3P3 (pin 25): Internal 3.3 V supply
20
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
www.ti.com .................................................................................................................................... SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009
Register Address Map
REGISTER
ADDRESS (HEX)
NAME
DEFUALT VALUE
0000 0000
DESCRIPTION
Enable control register
0
1
2
3
00
01
02
03
ENABLE
VADJUST
STATUS1
STATUS2
0000 0000
Voltage adjustment register
Status bit register
0000 0000
0000 0000
Status bit register
ENABLE Register (ENABLE), Address - 0X00H
DATA BIT
FIELD NAME
READ/WRITE
D7
Not used
R/W
D6
Not used
R/W
D5
VCTRL
R/W
D4
EN_BCK1
R/W
D3
EN_BCK2
R/W
D2
D1
EN_USB1
R/W
D0
EN_USB2
R/W
EN_BCK3
R/W
RESET
VALUE
0
0
0
0
0
0
0
0
FIELD NAME(1)
BIT DEFINITION
Voltage control bit for BUCK2 and BUCK3
0 – Nominal output voltage
VCTRL
1 – Enable voltage adjustment level set by VADJUST register
Enable BUCK1
0 – Disabled
1 - Enabled
EN_BCK1
EN_BCK2
EN_BCK3
EN-USB1
EN_USB2
Enable BUCK2
0 – Disabled
1 - Enabled
Enable BUCK3
0 – Disabled
1 - Enabled
Enable USB1
0 – Disabled (OFF)
1 - Enabled
Enable USB2
0 – Disabled (OFF)
1 – Enabled
(1) Enable bits EN_BCK1, EN_BCK2, and EN_BCK3 are ORed with EN_BCK1, EN_BCK2, and EN_BCK3 enable pins, respectively. To
disable a block, EN bit and EN pin must be low.
VADJUST Register (VADJUST), Address - 0X01H
DATA BIT
FIELD NAME
READ/WRITE
D7
Not used
R/W
D6
Not used
R/W
D5
Not used
R/W
D4
Not used
R/W
D3
D2
D1
D0
VBCK2[1:0]
VBCK3[1:0]
R/W
0
R/W
0
R/W
R/W
0
RESET
VALUE
0
0
0
0
0
FIELD NAME(1)
BIT DEFINITION
BUCK2 voltage adjustment
00 - Nominal
VBCK2[1:0]
VBCK3[1:0]
01 - 5% Decrease
10 - 10% Decrease
11 - 15% Decrease
BUCK3 voltage adjustment
00 - Nominal
01 - 5% Decrease
10 - 10% Decrease
11 - 15% Decrease
(1) Voltage adjustment settings for BUCK2 and BUCK3 are effective only when VCTRL pin is pulled high or VCTRL bit of ENABLE register
is set to ‘1’.
Copyright © 2009, Texas Instruments Incorporated
Submit Documentation Feedback
21
Product Folder Link(s): TPS65230 TPS65231
TPS65230, TPS65231
SLVSA10A–SEPTEMBER 2009–REVISED SEPTEMBER 2009.................................................................................................................................... www.ti.com
STATUS Register (STATUS1), Address - 0X02H
DATA BIT
FIELD NAME
READ/WRITE
D7
BOR
R
D6
TSD
R
D5
HOT
R
D4
UVLO
R
D3
UVLOB
R
D2
UVLOU
R
D1
USBFLG1
R
D0
USBFLG2
R
RESET
VALUE
0
0
0
0
0
0
0
0
FIELD NAME
BIT DEFINITION(1)
BOR
TSD
Brownout. This bit is set whenever the input voltage drops below 9.3 V.
Thermal shutdown
HOT
Thermal shutdown early warning
VIN under-voltage lockout
UVLO
UVLOB
UVLOU
USBFLG1
USBFLG2
VINB under-voltage lockout
VINU under-voltage lockout
USB fault flag (channel1)
USB fault flag (channel2)
(1) All status bits are cleared after register read access. INT output pin will go high-impedance (open drain output) after STATUS1 and
STATUS2 register have been read and / or all flags have been reset.
STATUS Register (STATUS2), Address - 0X03H
DATA BIT
FIELD NAME
READ/WRITE
D7
Not used
R
D6
Not used
R
D5
BCK1_UVD
R
D4
BCK2_UVD
R
D3
BCK3_UVD
R
D2
BCK1_PG
R
D1
BCK2_PG
R
D0
BCK3_PG
R
RESET
VALUE
0
0
0
0
0
0
0
0
FIELD NAME
BIT DEFINITION(1)
BCK1_UVD
BCK2_UVD
BCK3_UVD
BCK1_PG
BCK2_PG
BCK3_PG
Under voltage detect, BUCK1
Under voltage detect, BUCK2
Under voltage detect, BUCK3
Power Good, BUCK1
Power Good, BUCK2
Power Good, BUCK3
(1) Bits [5:3] are cleared after register read access. INT output pin will go high-impedance (open drain output) after STATUS1 and
STATUS2 register have been read and / or all flags have been reset.
22
Submit Documentation Feedback
Copyright © 2009, Texas Instruments Incorporated
Product Folder Link(s): TPS65230 TPS65231
PACKAGE OPTION ADDENDUM
www.ti.com
30-Oct-2009
PACKAGING INFORMATION
Orderable Device
TPS65230A2DCA
TPS65230A2DCAR
Status (1)
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
HTSSOP
DCA
48
40 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
HTSSOP
DCA
48
2000 Green (RoHS & CU NIPDAU Level-3-260C-168 HR
no Sb/Br)
TPS65231DCAR
TPS65231DCAT
PREVIEW HTSSOP
PREVIEW HTSSOP
DCA
DCA
48
48
TBD
TBD
Call TI
Call TI
Call TI
Call TI
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
Addendum-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Sep-2009
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS65230A2DCAR
HTSSOP DCA
48
2000
330.0
24.4
8.6
15.8
1.8
12.0
24.0
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
11-Sep-2009
*All dimensions are nominal
Device
Package Type Package Drawing Pins
HTSSOP DCA 48
SPQ
Length (mm) Width (mm) Height (mm)
346.0 346.0 41.0
TPS65230A2DCAR
2000
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, modifications, enhancements, improvements,
and other changes to its products and services at any time and to discontinue any product or service without notice. Customers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All products are
sold subject to TI’s terms and conditions of sale supplied at the time of order acknowledgment.
TI warrants performance of its hardware products to the specifications applicable at the time of sale in accordance with TI’s standard
warranty. Testing and other quality control techniques are used to the extent TI deems necessary to support this warranty. Except where
mandated by government requirements, testing of all parameters of each product is not necessarily performed.
TI assumes no liability for applications assistance or customer product design. Customers are responsible for their products and
applications using TI components. To minimize the risks associated with customer products and applications, customers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any TI patent right, copyright, mask work right,
or other TI intellectual property right relating to any combination, machine, or process in which TI products or services are used. Information
published by TI regarding third-party products or services does not constitute a license from TI to use such products or services or a
warranty or endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual
property of the third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of TI information in TI data books or data sheets is permissible only if reproduction is without alteration and is accompanied
by all associated warranties, conditions, limitations, and notices. Reproduction of this information with alteration is an unfair and deceptive
business practice. TI is not responsible or liable for such altered documentation. Information of third parties may be subject to additional
restrictions.
Resale of TI products or services with statements different from or beyond the parameters stated by TI for that product or service voids all
express and any implied warranties for the associated TI product or service and is an unfair and deceptive business practice. TI is not
responsible or liable for any such statements.
TI products are not authorized for use in safety-critical applications (such as life support) where a failure of the TI product would reasonably
be expected to cause severe personal injury or death, unless officers of the parties have executed an agreement specifically governing
such use. Buyers represent that they have all necessary expertise in the safety and regulatory ramifications of their applications, and
acknowledge and agree that they are solely responsible for all legal, regulatory and safety-related requirements concerning their products
and any use of TI products in such safety-critical applications, notwithstanding any applications-related information or support that may be
provided by TI. Further, Buyers must fully indemnify TI and its representatives against any damages arising out of the use of TI products in
such safety-critical applications.
TI products are neither designed nor intended for use in military/aerospace applications or environments unless the TI products are
specifically designated by TI as military-grade or "enhanced plastic." Only products designated by TI as military-grade meet military
specifications. Buyers acknowledge and agree that any such use of TI products which TI has not designated as military-grade is solely at
the Buyer's risk, and that they are solely responsible for compliance with all legal and regulatory requirements in connection with such use.
TI products are neither designed nor intended for use in automotive applications or environments unless the specific TI products are
designated by TI as compliant with ISO/TS 16949 requirements. Buyers acknowledge and agree that, if they use any non-designated
products in automotive applications, TI will not be responsible for any failure to meet such requirements.
Following are URLs where you can obtain information on other Texas Instruments products and application solutions:
Products
Amplifiers
Applications
Audio
Automotive
Broadband
Digital Control
Medical
Military
Optical Networking
Security
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
www.ti.com/audio
Data Converters
DLP® Products
DSP
Clocks and Timers
Interface
www.ti.com/automotive
www.ti.com/broadband
www.ti.com/digitalcontrol
www.ti.com/medical
www.ti.com/military
www.ti.com/opticalnetwork
www.ti.com/security
www.ti.com/telephony
www.ti.com/video
dsp.ti.com
www.ti.com/clocks
interface.ti.com
logic.ti.com
power.ti.com
microcontroller.ti.com
www.ti-rfid.com
Logic
Power Mgmt
Microcontrollers
RFID
Telephony
Video & Imaging
Wireless
RF/IF and ZigBee® Solutions www.ti.com/lprf
www.ti.com/wireless
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2009, Texas Instruments Incorporated
相关型号：
TPS65231DCAT
POWER MANAGEMENT IC FOR DIGITAL SET TOP BOXESWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232
TRIPLE BUCK POWER MANAGEMENT ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A0
采用 6mm x 6mm QFN 封装的宽输入电压电源管理 IC (PMIC)Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A0RHA
TRIPLE BUCK POWER MANAGEMENT ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A0RHAR
TRIPLE BUCK POWER MANAGEMENT ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A2
采用 HTSSOP 封装的宽输入电压电源管理 IC (PMIC)Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A2DCA
TRIPLE BUCK POWER MANAGEMENT ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65232A2DCAR
TRIPLE BUCK POWER MANAGEMENT ICWarning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65233
具有 I2C 接口电源管理 IC (PMIC) 的 LNB 稳压器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65233-1
具有 1MHz、I2C 接口电源管理 IC (PMIC) 的 LNB 稳压器Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65233-1RTER
具有 1MHz、I2C 接口电源管理 IC (PMIC) 的 LNB 稳压器 | RTE | 16 | -40 to 85Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
TPS65233-1RTET
具有 1MHz、I2C 接口电源管理 IC (PMIC) 的 LNB 稳压器 | RTE | 16 | -40 to 85Warning: Undefined variable $rtag in /www/wwwroot/website_ic37/www.icpdf.com/pdf/pdf/index.php on line 217
-
TI
©2020 ICPDF网 联系我们和版权申明