TPS70748PWPRG4 [TI]
IC 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20, PLASTIC, HTSSOP-20, Power Management Circuit;
| 型号： | TPS70748PWPRG4 |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | IC 2-CHANNEL POWER SUPPLY SUPPORT CKT, PDSO20, PLASTIC, HTSSOP-20, Power Management Circuit 输入元件 光电二极管 |
| 文件： | 总40页 (文件大小：896K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Dual-Output, Low Dropout Voltage Regulators
with Power-Up Sequencing for Split-Voltage DSP Systems
1
FEATURES
DESCRIPTION
23
•
Dual Output Voltages for Split-Supply
TPS707xx family devices are designed to provide a
complete power management solution for the
TMS320™ DSP family, processor power, ASIC,
FPGA, and digital applications where dual output
voltage regulators are required. Easy programmability
of the sequencing function makes the TPS707xx
family ideal for any TMS320 DSP applications with
power sequencing requirements. Differentiated
features, such as accuracy, fast transient response,
SVS supervisory circuit, manual reset inputs, and an
enable function, provide a complete system solution.
Applications
•
•
Selectable Power-Up Sequencing for DSP
Applications (See Part Number TPS708xx for
Independent Enable Outputs)
Output Current Range of 250mA on Regulator
1 and 125mA on Regulator 2
•
•
Fast Transient Response
Voltage Options: 3.3V/2.5V, 3.3V/1.8V,
3.3V/1.5V, 3.3V/1.2V, and Dual Adjustable
Outputs
The TPS707xx family of voltage regulators offer very
low dropout voltage and dual outputs with power-up
sequence control, which is designed primarily for
DSP applications. These devices have extremely low
noise output performance without using any added
filter bypass capacitors and are designed to have a
fast transient response and be stable with 10µF low
ESR capacitors.
•
•
•
•
•
•
•
•
•
•
•
Open Drain Power-On Reset with 120ms Delay
Open Drain Power Good for Regulator 1
Ultralow 190µA (typ) Quiescent Current
1µA Input Current During Standby
Low Noise: 65µVRMS Without Bypass Capacitor
Quick Output Capacitor Discharge Feature
Two Manual Reset Inputs
These devices have fixed 3.3V/2.5V, 3.3V/1.8V,
3.3V/1.5V, 3.3V/1.2V, and adjustable/adjustable
voltage options. Regulator 1 can support up to
250mA, and regulator 2 can support up to 125mA.
Separate voltage inputs allow the designer to
configure the source power.
2% Accuracy Over Load and Temperature
Undervoltage Lockout (UVLO) Feature
20-Pin PowerPAD™ TSSOP Package
Thermal Shutdown Protection
PWP PACKAGE
(TOP VIEW)
NC
1
2
3
4
5
6
7
8
9
10
20
19
18
17
16
15
14
13
12
11
NC
V
V
IN1
OUT1
V
IN1
V
V
OUT1
MR1
MR2
EN
SEQ
GND
/FB1
/FB2
SENSE1
PG1
RESET
V
V
V
SENSE2
OUT2
V
IN2
V
IN2
OUT2
NC
1
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
2
3
PowerPAD, TMS320 are trademarks of Texas Instruments.
All other trademarks are the property of their respective owners.
PRODUCTION DATA information is current as of publication date.
Products conform to specifications per the terms of the Texas
Instruments standard warranty. Production processing does not
necessarily include testing of all parameters.
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TPS70751 PWP
DSP
I/O
3.3 V
V
OUT1
5 V
V
IN1
10 mF
0.1 mF
V
SENSE1
250 kW
PG1
PG1
MR2
MR2
>2 V
V
IN2
250 kW
<0.7 V
0.1 mF
RESET
RESET
MR1
MR1
EN
<0.7 V
>2 V
>2 V
EN
<0.7 V
V
SENSE2
SEQ
1.8 V
Core
V
OUT2
10 mF
Because the PMOS device behaves as a low-value resistor, the dropout voltage is very low (typically 83mV on
regulator 1) and is directly proportional to the output current. Additionally, because the PMOS pass element is a
voltage-driven device, the quiescent current is very low and independent of output loading (maximum of 230µA
over the full range of output current). This LDO family also features a sleep mode; applying a high signal to EN
(enable) shuts down both regulators, reducing the input current to 1µA at TJ = +25°C.
The device is enabled when the EN pin is connected to a low-level input voltage. The output voltages of the two
regulators are sensed at the VSENSE1 and VSENSE2 pins, respectively.
The input signal at the SEQ pin controls the power-up sequence of the two regulators. When the device is
enabled and the SEQ terminal is pulled high or left open, VOUT2 turns on first and VOUT1 remains off until VOUT2
reaches approximately 83% of its regulated output voltage. At that time VOUT1 is turned on. If VOUT2 is pulled
below 83% (for example, an overload condition), VOUT1 is turned off. Pulling the SEQ terminal low reverses the
power-up order and VOUT1 is turned on first. The SEQ pin is connected to an internal pull-up current source.
For each regulator, there is an internal discharge transistor to discharge the output capacitor when the regulator
is turned off (disabled).
The PG1 pin reports the voltage conditions at VOUT1, which can be used to implement an SVS for the circuitry
supplied by regulator 1.
The TPS707xx features a RESET (SVS, POR, or Power-On Reset). RESET output initiates a reset in DSP
systems and related digital applications in the event of an undervoltage condition. RESET indicates the status of
VOUT2 and both manual reset pins (MR1 and MR2). When VOUT2 reaches 95% of its regulated voltage and MR1
and MR2 are in the logic high state, RESET goes to a high impedance state after a 120ms delay. RESET goes
to the logic low state when the VOUT2 regulated output voltage is pulled below 95% (for example, an overload
condition) of its regulated voltage. To monitor VOUT1, the PG1 output pin can be connected to MR1 or MR2.
The device has an undervoltage lockout (UVLO) circuit that prevents the internal regulators from turning on until
VIN1 reaches 2.5V.
2
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
This integrated circuit can be damaged by ESD. Texas Instruments recommends that all integrated circuits be handled with
appropriate precautions. Failure to observe proper handling and installation procedures can cause damage.
ESD damage can range from subtle performance degradation to complete device failure. Precision integrated circuits may be more
susceptible to damage because very small parametric changes could cause the device not to meet its published specifications.
ORDERING INFORMATION(1)
VOLTAGE (V)(2)
PACKAGE-
LEAD
(DESIGNATOR)
SPECIFIED
TEMPERATURE
RANGE (TJ)
ORDERING
NUMBER
TRANSPORT
MEDIA, QUANTITY
PRODUCT
VOUT1
VOUT2
TPS70702PWP
TPS70702PWPR
TPS70745PWP
TPS70745PWPR
TPS70748PWP
TPS70748PWPR
TPS70751PWP
TPS70751PWPR
TPS70758PWP
TPS70758PWPR
Tube, 70
Tape and Reel, 2000
Tube, 70
TPS70702
Adjustable
Adjustable HTSSOP-24 (PWP)
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
-40°C to +125°C
TPS70745
TPS70748
TPS70751
TPS70758
3.3 V
3.3 V
3.3 V
3.3 V
1.2 V
1.5 V
1.8 V
2.5 V
HTSSOP-24 (PWP)
HTSSOP-24 (PWP)
HTSSOP-24 (PWP)
HTSSOP-24 (PWP)
Tape and Reel, 2000
Tube, 70
Tape and Reel, 2000
Tube, 70
Tape and Reel, 2000
Tube, 70
Tape and Reel, 2000
(1) For the most current package and ordering information see the Package Option Addendum located at the end of this document, or see
the TI web site at www.ti.com.
(2) For fixed 1.20V operation, tie FB to OUT.
ABSOLUTE MAXIMUM RATINGS
Over operating free-air temperature range (unless otherwise noted)(1)
TPS707xx
–0.3 to +7
–0.3 to +7
5.5
UNIT
V
(2)
Input voltage range: VIN1, VIN2
Voltage range at EN
V
Output voltage range (VOUT1, VSENSE1
Output voltage range (VOUT2, VSENSE2
Maximum RESET, PG1 voltage
)
V
)
5.5
V
7
V
Maximum MR1, MR2, and SEQ voltage
Peak output current
VIN1
V
Internally limited
See Dissipation Ratings Table
–40 to +150
Continuous total power dissipation
Junction temperature range, TJ
Storage temperature range, Tstg
ESD rating, HBM
°C
°C
kV
–65 to +150
2
(1) Stresses beyond those listed under absolute maximum ratings may cause permanent damage to the device. These are stress ratings
only, and functional operation of the device at these or any other conditions beyond those indicated under recommended operating
conditions is not implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
(2) All voltages are tied to network ground.
DISSIPATION RATINGS
DERATING
PACKAGE
AIR FLOW (CFM)
T
A ≤ +25°C
FACTOR
TA = +70°C
1.687W
TA = +85°C
1.227W
0
3.067W
30.67mW/°C
41.15mW/°C
PWP(1)
250
4.115W
2.265W
1.646W
(1) This parameter is measured with the recommended copper heat sink pattern on a 4-layer PCB, 1 oz. copper on a 4-in by 4-in ground
layer. For more information, refer to TI technical brief SLMA002.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
3
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
RECOMMENDED OPERATING CONDITIONS
Over operating temperature range (unless otherwise noted).
MIN
2.7
0
MAX
6
UNIT
V
Input voltage, VI(1)(regulator 1 and 2)
Output current, IO (regulator 1)
250
125
5.5
mA
mA
V
Output current, IO (regulator 2)
0
Output voltage range (for adjustable option)
Operating junction temperature, TJ
1.22
–40
+125
°C
(1) To calculate the minimum input voltage for maximum output current, use the following equation: VI(min) = VO(max) + VDO(max load)
.
ELECTRICAL CHARACTERISTICS
Over recommended operating junction temperature range (TJ = –40°C to +125°C), VIN1 or VIN2 = VOUT(nom) + 1V, IO = 1mA,
EN = 0V, and CO = 33µF (unless otherwise noted).
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX UNIT
2.7V < VI < 6V,
TJ = +25°C
FB connected to VO
1.22
Reference
voltage
2.7V < VI < 6V,
2.7V < VI < 6V,
2.7V < VI < 6V,
2.7V < VI < 6V,
2.7V < VI < 6V,
2.8V < VI < 6V,
2.8V < VI < 6V,
3.5V < VI < 6V,
3.5V < VI < 6V,
4.3V < VI < 6V,
FB connected to VO
1.196
1.176
1.47
1.244
1.224
TJ = +25°C
1.2
1.5
1.2V Output
1.5V Output
1.8V Output
2.5V Output
3.3V Output
TJ = +25°C
TJ = +25°C
TJ = +25°C
TJ = +25°C
TJ = +25°C
Output
voltage
1.53
1.836
2.55
VO
V
(1),(2)
1.8
1.764
2.45
2.5
3.3
4.3V < VI < 6V,
(2)
3.234
3.366
230
Quiescent current (GND current) for
regulator 1 and regulator 2, EN = 0V(1)
190
µA
(2)
Output voltage line regulation (∆VO/VO) VO + 1V < VI ≤ 6V,
TJ = +25°C(1)
(1)
0.01%
(3)
for regulator 1 and regulator 2
VO + 1V < VI ≤ 6V
V
0.1%
(2)
Load regulation for VOUT 1 and VOUT2
TJ = +25°C
1
65
mV
Vn
Output noise Regulator 1
BW = 300Hz to 50kHz,
CO = 33µF, TJ = +25°C
µVRMS
voltage
Regulator 2
65
Regulator 1
1.6
1.9
1
Output current limit
VOUT = 0V
µA
°C
µA
Regulator 2
0.750
+150
Thermal shutdown junction temperature
EN = VI,
TJ = +25°C
TJ = +25°C
TJ = +25°C(1)
2
6
2
6
Regulator 1
EN = VI
II
Standby
(standby) current
EN = VI,
Regulator 2
µA
EN = VI
PSRR
Power-supply ripple
rejection
f = 1kHz, CO = 33µF,
dB
60
(1) Minimum input operating voltage is 2.7V or VO(typ) + 1V, whichever is greater. Maximum input voltage = 6V, minimum output
current = 1mA.
(2) IO = 1mA to 250mA for Regulator 1 and 1mA to 125mA for Regulator 2.
ǒ
Ǔ
VImax*2.7V
LineReg. (mV) + (%ńV) VO
1000
ǒV100 *ǒV )1VǓǓ
(3) If VO < 1.8V then VImax = 6V, VImin = 2.7V:
If VO > 2.5V then VImax = 6V, VImin = VO + 1V:
Imax
O
LineReg. (mV) + (%ńV) VO
1000
100
4
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
ELECTRICAL CHARACTERISTICS (continued)
Over recommended operating junction temperature range (TJ = –40°C to +125°C), VIN1 or VIN2 = VOUT(nom) + 1V, IO = 1mA,
EN = 0V, and CO = 33µF (unless otherwise noted).
PARAMETER
RESET Terminal
Minimum input voltage for valid RESET IRESET = 300µA,
TEST CONDITIONS
MIN
TYP
MAX UNIT
V(RESET) ≤ 0.8V
1.0
95%
0.5%
120
1.3
V
Trip threshold voltage
Hysteresis voltage
t(RESET)
VO decreasing
92%
80
98% VOUT
VOUT
Measured at VO
RESET pulse duration
Rising edge deglitch
VI = 3.5V,
160
ms
µs
V
tr(RESET)
30
Output low voltage
Leakage current
IO(RESET) = 1mA
0.15
0.4
1
V(RESET) = 6V
µA
PG1 Terminal
Minimum input voltage for valid PG1
Trip threshold voltage
Hysteresis voltage
tf(PG1)
I(PG1) = 300µA,
VO decreasing
Measured at VO
Falling edge deglitch
VI = 2.7V,
V
(PG1) ≤ 0.8V
1.0
95%
0.5%
30
1.3
V
92%
98% VOUT
VOUT
µs
Output low voltage
Leakage current
IO(PG1) = 1mA
0.15
0.4
1
V
V(PG1) = 6V
µA
EN Terminal
High level EN input voltage
Low level EN input voltage
Input current (EN)
SEQ Terminal
2
–1
2
V
V
0.7
1
µA
High level SEQ input voltage
Low level SEQ input voltage
Falling edge delay
SEQ pull-up current source
MR1 / MR2 Terminals
High level input voltage
Low level input voltage
Pull-up current source
VOUT2 Terminal
V
V
0.7
0.7
Measured at VO
140
6
µs
µA
2
V
V
6
µA
VOUT2 UV comparator: Positive-going
input threshold voltage of VOUT2 UV
comparator
80% VO 83% VO 86% VO
V
VOUT2 UV comparator: Falling edge
deglitch
VSENSE_2 decreasing below threshold
140
µs
Peak output current
2ms pulse width
VOUT2 = 1.5V
375
7.5
mA
mA
Discharge transistor current
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
5
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
ELECTRICAL CHARACTERISTICS (continued)
Over recommended operating junction temperature range (TJ = –40°C to +125°C), VIN1 or VIN2 = VOUT(nom) + 1V, IO = 1mA,
EN = 0V, and CO = 33µF (unless otherwise noted).
PARAMETER
VOUT1 Terminal
TEST CONDITIONS
MIN
TYP
MAX UNIT
VOUT1 UV comparator: Positive-going
input threshold voltage of VOUT1 UV
comparator
80% VO 83% VO 86% VO
V
VOUT1 UV comparator: Hysteresis
0.5% VO
140
mV
VOUT1 UV comparator: Falling edge
deglitch
VSENSE_1 decreasing below threshold
µs
Dropout voltage(4)
Dropout voltage(4)
Peak output current(4)
Discharge transistor current
VIN1 UVLO threshold
FB Terminal
IO = 250mA, TJ = +25°C
IO = 250mA,
VIN1 = 3.2V
VIN1 = 3.2V
83
140
750
7.5
mV
mV
mA
mA
V
2ms pulse width
VOUT1 = 1.5V
2.4
2.65
Input current: TPS70702
FB = 1.8V
1
µA
(4) Input voltage (VIN1 or VIN2) = VO(typ) – 100mV. For 1.5V, 1.8V and 2.5V regulators, the dropout voltage is limited by input voltage range.
The 3.3V regulator input is set to 3.2V to perform this test.
6
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
DEVICE INFORMATION
Fixed Voltage Version
V
V
(2 Pins)
V
(2 Pins)
IN1
OUT1
UVLO1
Comp
10 kW
Current
Sense
-
ENA_1
SENSE1
+
2.5 V
(see Note A)
-
+
ENA_1
Reference
V
ref
FB1
GND
Thermal
V
ref
Shutdown
PG1
-
FB1
0.95 x V
Rising Edge
Deglitch
+
ref
V
IN1
PG
Comp
MR2
Reset
Comp
RESET
-
FB2
0.95 x V
Falling Edge
Delay
Rising Edge
Deglitch
+
ref
VOUT2 UV Comp
V
IN1
-
FB2
Falling Edge
Deglitch
ENA_1
ENA_2
+
0.83 x V
ref
Power
Sequence
Logic
MR1
-
FB1
Falling Edge
Deglitch
V
ref
+
0.83 x V
ref
V
UV Comp
-
+
OUT1
ENA_2
EN
V
IN1
V
SENSE2
Current
Sense
ENA_2
(see Note A)
10 kW
SEQ
(see Note B)
V
(2 Pins)
OUT2
V
(2 Pins)
IN2
A. For most applications, VSENSE1 and VSENSE2 should be externally connected to VOUT as close as possible to the
device. For other implementations, refer to SENSE terminal connection discussion in the Application Information
section.
B. If the SEQ terminal is floating at the input, VOUT2 powers up first.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
7
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Adjustable Voltage Version
V
(2 Pins)
V
(2 Pins)
OUT1
IN1
UVLO
Comp
Current
Sense
-
FB1
ENA_1
+
2.5 V
(see Note A)
-
+
ENA_1
Reference
V
ref
GND
Thermal
V
ref
Shutdown
PG1
-
FB1
Rising Edge
Deglitch
+
0.95 x V
ref
V
IN1
PG
Comp
MR2
Reset
Comp
RESET
-
FB2
0.95 x V
Falling Edge
Delay
Rising Edge
Deglitch
+
ref
V
UV Comp
OUT2
V
IN1
-
FB2
Falling Edge
Deglitch
ENA_1
ENA_2
+
0.83 x V
ref
Power
Sequence
Logic
MR1
-
FB1
Falling Edge
Deglitch
V
ref
+
0.83 x V
ref
V
UV Comp
-
+
OUT1
ENA_2
EN
V
IN1
FB2
Current
Sense
ENA_2
(see Note A)
SEQ
(see Note B)
V
(2 Pins)
OUT2
V
(2 Pins)
IN2
A. For most applications, FB1 and FB2 should be externally connected to resistor dividers as close as possible to the
device. For other implementations, refer to FB terminals connection discussion in the Application Information
section.
B. If the SEQ terminal is floating at the input, VOUT2 powers up first
8
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
RESET Timing Diagram (with VIN1 Powered Up)
V
IN2
V
RES
V
RES
(see Note A)
t
V
OUT2
V
IT+
(see Note B)
V
IT+
(see Note B)
Threshold
Voltage
V
IT−
V
IT−
(see Note B)
(see Note B)
t
RESET
Output
120 ms
Delay
120 ms
Delay
Output
Undefined
Output
Undefined
t
NOTES: A.
B.
V
is the minimum input voltage for a valid RESET. The symbol V
is not currently listed within EIA or JEDEC standards
RES
RES
for semiconductor symbology.
−Trip voltage is typically 5% lower than the output voltage (95%V ) V to V is the hysteresis voltage.
V
IT
O
IT−
IT+
PG1 Timing Diagram
V
IN1
V
UVLO
V
UVLO
V
PG1
V
PG1
(see Note A)
t
V
OUT2
V
IT+
(see Note B)
V
IT+
(see Note B)
Threshold
Voltage
V
IT−
V
IT−
(see Note B)
(see Note B)
t
PG1
Output
Output
Undefined
Output
Undefined
t
NOTES: A.
B.
V
is the minimum input voltage for a valid PG1. The symbol V
is not currently listed within EIA or JEDEC
PG1
PG1
standards for semiconductor symbology.
V
IT
−Trip voltage is typically 5% lower than the output voltage (95%V ) V to V is the hysteresis voltage.
O IT− IT+
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
9
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Table 1. TERMINAL FUNCTIONS
TERMINAL
I/O
DESCRIPTION
NAME
EN
NO.
6
I
—
I
Active low enable
GND
MR1
MR2
NC
8
Ground
4
5
Manual reset input 1, active low, pulled up internally
Manual reset input 2, active low, pulled up internally
No connection
I
1, 11, 20
—
Open drain output, low when VOUT1 voltage is less than 95% of the nominal regulated
voltage
PG1
16
15
7
O
O
I
RESET
SEQ
Open drain output, SVS (power-on reset) signal, active low
Power-up sequence control: SEQ = High, VOUT2 powers up first;
SEQ = Low, VOUT1 powers up first, SEQ terminal pulled up internally.
VIN1
2, 3
9, 10
18, 19
12, 13
14
I
I
Input voltage of regulator 1
VIN2
Input voltage of regulator 2
VOUT1
O
O
I
Output voltage of regulator 1
VOUT2
Output voltage of regulator 2
VSENSE2/FB2
VSENSE1/FB1
Regulator 2 output voltage sense/regulator 2 feedback for adjustable
Regulator 1 output voltage sense/regulator 1 feedback for adjustable
17
I
Detailed Description
The TPS707xx low dropout regulator family provides dual regulated output voltages for DSP applications that
require high-performance power management solutions. These devices provide fast transient response and high
accuracy with small output capacitors, while drawing low quiescent current. Programmable sequencing provides
a power solution for DSPs without any external component requirements. This architecture reduces the
component cost and board space while increasing total system reliability. The TPS707xx family has an enable
feature that puts the device in sleep mode, reducing the input currents to less than 3µA. Other features are
integrated SVS (Power-On Reset, RESET) and Power Good (PG1) that monitor output voltages and provide
logic output to the system. These differentiated features provide a complete DSP power solution.
The TPS707xx, unlike many other LDOs, feature very low quiescent current that remains virtually constant even
with varying loads. Conventional LDO regulators use a pnp pass element, the base current of which is directly
proportional to the load current through the regulator (IB = IC/β). The TPS707xx uses a PMOS transistor to pass
current; because the gate of the PMOS is voltage=driven, operating current is low and stable over the full load
range.
Pin Functions
Enable
The EN terminal is an input that enables or shuts down the device. If EN is at a voltage high signal, the device is
in shutdown mode. When EN goes to voltage low, the device is enabled.
Sequence
The SEQ terminal is an input that programs which output voltage (VOUT1 or VOUT2) turns on first. When the device
is enabled and the SEQ terminal is pulled high or left open, VOUT2 turns on first and VOUT1 remains off until VOUT2
reaches approximately 83% of its regulated output voltage. At that time, VOUT1 is turned on. If VOUT2 is pulled
below 83% (for example, in an overload condition) VOUT1 is turned off. These terminals have a 6-µA pullup
current to VIN1
.
Pulling the SEQ terminal low reverses the power-up order and VOUT1 is turned on first. For detailed timing
diagrams, refer to Figure 36 through Figure 40.
10
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Power-Good
The PG1 is an open drain, active high output terminal that indicates the status of the VOUT1 regulator. When the
VOUT1 reaches 95% of its regulated voltage, PG1 goes to a high impedance state. It goes to a low impedance
state when it is pulled below 95% (for example, doing an overload condition) of its regulated voltage. The open
drain output of the PG1 terminal requires a pull-up resistor.
Manual Reset Pins (MR1 and MR2)
MR1 and MR2 are active low input terminals used to trigger a reset condition. When either MR1 or MR2 is pulled
to logic low, a POR (RESET) occurs. These terminals have a 6-µA pull-up current to VIN1
.
Sense (VSENSE1, VSENSE2
)
The sense terminals of fixed-output options must be connected to the regulator output, and the connection
should be as short as possible. Internally, sense connects to high-impedance, wide-bandwidth amplifiers through
a resistor-divider network and noise pickup feeds through to the regulator output. It is essential to route the
sense connection in such a way to minimize or avoid noise pickup. Adding RC networks between the VSENSE
terminals and VOUT terminals to filter noise is not recommended because these networks can cause the
regulators to oscillate.
FB1 and FB2
FB1 and FB2 are input terminals used for adjustable-output devices and must be connected to the external
feedback resistor divider. FB1 and FB2 connections should be as short as possible. It is essential to route them
in such a way as to minimize or avoid noise pickup. Adding RC networks between the FB terminals and VOUT
terminals to filter noise is not recommended because these networks can cause the regulators to oscillate.
RESET Indicator
The TPS707xx features a RESET (SVS, POR, or Power-On Reset). RESET can be used to drive power-on reset
circuitry or a low-battery indicator. RESET is an active low, open drain output that indicates the status of the
VOUT2 regulator and both manual reset pins (MR1 and MR2). When VOUT2 exceeds 95% of its regulated voltage,
and MR1 and MR2 are in the high impedance state, RESET goes to a high-impedance state after 120ms delay.
RESET goes to a low-impedance state when VOUT2 is pulled below 95% (for example, an overload condition) of
its regulated voltage. To monitor VOUT1, the PG1 output pin can be connected to MR1 or MR2. The open drain
output of the RESET terminal requires a pullup resistor. If RESET is not used, it can be left floating.
VIN1 and VIN2
VIN1 and VIN2 are input to the regulators. Internal bias voltages are powered by VIN1
.
VOUT1 and VOUT2
VOUT1 and VOUT2 are output terminals of the LDO.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
11
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TYPICAL CHARACTERISTICS
Table 2. Table of Graphs
FIGURE
vs Output current
vs Temperature
vs Junction temperature
vs Frequency
Figure 1 to Figure 3
Figure 4 to Figure 7
Figure 8
VO
Output voltage
Ground current
PSRR
ZO
Power-supply rejection ratio
Output spectral noise density
Output impedance
Figure 9 to Figure 12
Figure 13 to Figure 16
Figure 17 to Figure 20
Figure 21 and Figure 22
Figure 23 and Figure 24
Figure 25 and Figure 26
Figure 27 and Figure 28
Figure 29 and Figure 30
Figure 31 to Figure 34
Figure 35
vs Frequency
vs Frequency
vs Temperature
vs Input voltage
Dropout voltage
Load transient response
Line transient response
VO
Output voltage and enable voltage
Equivalent series resistance
vs Time (start-up)
vs Output current
Test circuit for typical regions of stability (equivalent series resistance) performance
TPS70751
OUTPUT VOLTAGE
vs
TPS70751
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
OUTPUT CURRENT
3.300
3.299
3.298
3.297
3.296
3.295
3.294
1.802
V
= 4.3 V
= 25°C
IN1
V
= 2.8V
IN2
= 25°C
T
A
T
A
1.801
1.800
VOUT1
VOUT2
1.799
1.798
1.797
1.796
1.795
3.293
3.292
0
0.1
0.2
0.3
0.4
0.5
0.6
0
0.05
0.1
0.15
0.2
0.25
0.3
I
O
− Output Current − A
I
O
− Output Current − A
Figure 1.
Figure 2.
12
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TPS70745
OUTPUT VOLTAGE
vs
TPS70751
OUTPUT VOLTAGE
vs
OUTPUT CURRENT
TEMPERATURE
1.201
1.200
3.286
3.284
3.282
V
I
= 4.3 V
= 1 mA
V
= 2.7 V
IN1
IN2
T = 25°C
O
A
VOUT1
VOUT2
3.280
3.278
3.276
3.274
3.272
1.199
1.198
1.197
1.196
3.270
3.268
1.195
0
0.05
0.1
0.15
0.2
0.25
0.3
−40 −25 −10
5
20 35 50 65 80 95 110 125
T − Temperature − °C
I
O
− Output Current − A
Figure 3.
Figure 4.
TPS70751
TPS70751
OUTPUT VOLTAGE
vs
OUTPUT VOLTAGE
vs
TEMPERATURE
TEMPERATURE
3.288
3.286
3.284
3.282
3.280
1.800
V
I
= 4.3 V
= 500 mA
V
I
= 2.8 V
= 1 mA
IN1
IN2
O
O
1.798
VOUT1
VOUT2
1.796
1.794
3.278
3.276
3.274
1.792
1.790
1.788
1.786
3.272
3.270
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
T − Temperature − °C
T − Temperature − °C
Figure 5.
Figure 6.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
13
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TPS70751
OUTPUT VOLTAGE
vs
GROUND CURRENT
vs
JUNCTION TEMPERATURE
TEMPERATURE
210
200
190
1.799
V
= 2.8 V
= 250 mA
IN2
Regulator 1 and Regulator 2
I
O
1.798
1.797
1.796
1.795
1.794
1.793
VOUT2
I
I
= 1 mA
= 1 mA
OUT1
OUT2
180
170
I
I
= 250 mA
= 500 mA
OUT1
OUT2
1.792
1.791
1.790
160
150
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
T − Temperature − °C
T − Junction Temperature − °C
J
Figure 7.
Figure 8.
TPS70751
TPS70751
POWER-SUPPLY REJECTION RATIO
POWER-SUPPLY REJECTION RATIO
vs
vs
FREQUENCY
FREQUENCY
−10
10
I
C
= 10 mA
O
I
C
= 500 mA
O
0
= 22 µF
−20
−30
−40
O
= 22 µF
O
VOUT1
VOUT1
−10
−20
−30
−40
−50
−50
−60
−70
−60
−70
−80
−90
−80
−90
10
100
1 k
10 k
100 k
1 M
10
100
1 k
10 k
100 k
1 M
f − Frequency − Hz
f − Frequency − Hz
Figure 9.
Figure 10.
14
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TPS70751
TPS70751
POWER-SUPPLY REJECTION RATIO
POWER-SUPPLY REJECTION RATIO
vs
vs
FREQUENCY
FREQUENCY
−10
10
0
I
C
= 10 mA
I
O
= 250 mA
O
= 22 µF
C = 22 µF
O
VOUT2
−20
O
VOUT2
−30
−40
−10
−20
−50
−60
−70
−30
−40
−50
−80
−90
−60
−70
10
100
1 k
10 k
100 k
1 M
10
100
1 k
10 k
100 k
1 M
f − Frequency − Hz
f − Frequency − Hz
Figure 11.
Figure 12.
OUTPUT SPECTRAL NOISE DENSITY
OUTPUT SPECTRAL NOISE DENSITY
vs
vs
FREQUENCY
FREQUENCY
10
10
V
V
I
= 4.3 V
= 3.3 V
= 10 mA
V
V
I
= 4.3 V
= 3.3 V
= 500 mA
IN1
OUT1
IN1
OUT1
O
O
1
1
0.1
0.01
0.1
0.01
100
1 k
f − Frequency − Hz
Figure 13.
10 k
100 k
100
1 k
10 k
100 k
f − Frequency − Hz
Figure 14.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
15
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
OUTPUT SPECTRAL NOISE DENSITY
OUTPUT SPECTRAL NOISE DENSITY
vs
vs
FREQUENCY
FREQUENCY
10
10
V
V
I
= 2.8 V
= 1.8 V
= 10 mA
V
V
I
= 2.8 V
= 1.8 V
= 250 mA
IN2
OUT2
IN2
OUT2
O
O
1
1
0.1
0.1
0.01
0.01
100
1 k
10 k
100 k
100
1 k
10 k
100 k
f − Frequency − Hz
f − Frequency − Hz
Figure 15.
Figure 16.
OUTPUT IMPEDANCE
vs
OUTPUT IMPEDANCE
vs
FREQUENCY
FREQUENCY
100
100
C
I
= 33 mF
C
I
= 33 mF
O
O
= 500 mA
= 3.3 V
= 10 mA
= 3.3 V
O
O
V
T
V
T
O
O
= 25°C
= 25°C
A
A
10
10
1
1
0.1
0.1
0.01
0.01
10
100
1 k
10 k
100 k
1 M
10 M
10
100
1 k
10 k
100 k
1 M
10 M
f - Frequency - Hz
f - Frequency - Hz
Figure 17.
Figure 18.
16
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
OUTPUT IMPEDANCE
vs
OUTPUT IMPEDANCE
vs
FREQUENCY
FREQUENCY
100
100
C
O
= 33 mF
C = 33 mF
O
I
= 250 mA
= 1.8 V
I
= 10 mA
= 1.8 V
O
O
O
V
V
O
T
A
= 25°C
T
A
= 25°C
10
10
1
1
0.1
0.1
0.01
0.01
10
100
1 k
10 k
100 k
1 M
10 M
10
100
1 k
10 k
100 k
1 M
10 M
f - Frequency - Hz
f - Frequency - Hz
Figure 19.
Figure 20.
DROPOUT VOLTAGE
vs
DROPOUT VOLTAGE
vs
TEMPERATURE
TEMPERATURE
6
5
250
200
C
= 33 µF
C
= 33 µF
O
O
VIN1 = 3.2 V
VIN1 = 3.2 V
I
O
= 10 mA
I
O
= 500 mA
4
3
2
150
100
50
0
1
0
I
O
= 0 mA
−40 −25 −10
5
20 35 50 65 80 95 110 125
−40 −25 −10
5
20 35 50 65 80 95 110 125
T − Temperature − °C
T − Temperature − °C
Figure 21.
Figure 22.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
17
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TPS70702
DROPOUT VOLTAGE
vs
TPS70702
DROPOUT VOLTAGE
vs
INPUT VOLTAGE
INPUT VOLTAGE
300
250
500
400
I
= 500 mA
O
I
= 250 mA
O
VIN1
VIN2
T = 125°C
J
200
T = 125°C
J
300
200
T = 25°C
J
150
100
50
T = 25°C
J
T = −40°C
J
T = −40°C
J
100
0
0
2.5
3
3.5
4
4.5
5
5.5
2.5
3
3.5
4
4.5
5
5.5
V − Input Voltage − V
I
V − Input Voltage − V
I
Figure 23.
Figure 24.
LOAD TRANSIENT RESPONSE
LOAD TRANSIENT RESPONSE
C
T
= 33 µF
= 25°C
C
T
= 33 µF
= 25°C
o
o
500
A
A
V
OUT2
= 1.8 V
V
OUT1
= 3.3 V
250
0
250
0
20
0
20
0
−20
−20
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
t − Time − ms
t − Time − ms
Figure 25.
Figure 26.
18
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
LINE TRANSIENT RESPONSE
LINE TRANSIENT RESPONSE
3.8
2.8
5.3
4.3
50
0
10
0
I
O
= 250 mA
I
O
= 500 mA
C
V
= 33 µF
−50
C
= 33 µF
o
−10
o
V
OUT1
OUT2
0
20 40 60 80 100 120 140 160 180 200
0
20 40 60 80 100 120 140 160 180 200
t − Time − µs
t − Time − µs
Figure 27.
Figure 28.
OUTPUT VOLTAGE AND ENABLE VOLTAGE
OUTPUT VOLTAGE AND ENABLE VOLTAGE
vs
vs
TIME (START-UP)
TIME (START-UP)
V
= 1.8 V
V
= 3.3 V
O
O
3
2
2
1
C = 33 µF
C = 33 µF
o
o
I
O
= 250 mA
I
O
= 500 mA
V
OUT2
V
OUT1
SEQ = High
SEQ = Low
1
0
0
−1
5
5
0
0
−5
−5
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
0
0.2 0.4 0.6 0.8
1
1.2 1.4 1.6 1.8
2
t − Time (Start-Up) − ms
t − Time (Start-Up) − ms
Figure 29.
Figure 30.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
19
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
REGION OF INSTABILITY
REGION OF INSTABILITY
V
= 3.3 V
O
V
= 3.3 V
O
C
= 10 mF
O
C
= 6.8 mF
= 25°C
O
T
= 25°C
J
T
J
1
1
0.1
50 mW
250 mW
REGION OF INSTABILITY
REGION OF INSTABILITY
0.1
0.01
0
50
100
150
200
250
0
50
100
150
200
250
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 31.
Figure 32.
TYPICAL REGION OF STABILITY
TYPICAL REGION OF STABILITY
EQUIVALENT SERIES RESISTANCE(1)
vs
EQUIVALENT SERIES RESISTANCE(1)
vs
OUTPUT CURRENT
OUTPUT CURRENT
10
10
REGION OF INSTABILITY
REGION OF INSTABILITY
V
= 1.8 V
V
= 1.8 V
= 10 mF
O
O
C
= 6.8 mF
C
O
O
T
= 25°C
T
= 25°C
J
J
1
1
0.1
50 mW
250 mW
REGION OF INSTABILITY
REGION OF INSTABILITY
0.1
0.01
0
25
50
75
100
125
0
25
50
75
100
125
I
- Output Current - mA
I
- Output Current - mA
O
O
Figure 33.
Figure 34.
(1) Equivalent series resistance (ESR) refers to the total series resistance, including the ESR of the capacitor, any
series resistance added externally, and PWB trace resistance to CO.
20
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
To Load
IN
V
I
OUT
+
R
C
O
R
L
EN
GND
ESR
Figure 35. Test Circuit for Typical Regions of Stability
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
21
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
APPLICATION INFORMATION
TPS707xxPWP
Sequencing Timing Diagrams
(Fixed Output Option)
V
This section provides a number of timing diagrams
showing how this device functions in different
configurations.
OUT1
V
I
V
V
IN1
OUT1
0.1 mF
10 mF
V
SENSE1
Application condition: VIN1 and VIN2 are tied to the
same fixed input voltage greater than the VUVLO; SEQ
is tied to logic low; PG1 is tied to MR2; MR1 is left
unconnected and is therefore at logic high.
250 kW
PG1
MR2
MR2
V
IN2
EN is initially high; therefore, both regulators are off
and PG1 and RESET are at logic low. With SEQ at
logic low, when EN is taken to logic low, VOUT1 turns
on. VOUT2 turns on after VOUT1 reaches 83% of its
regulated output voltage. When VOUT1 reaches 95%
of its regulated output voltage, PG1 (tied to MR2)
goes to logic high. When both VOUT1 and VOUT2 reach
95% of their respective regulated output voltages and
both MR1 and MR2 (tied to PG1) are at logic high,
RESET is pulled to logic high after a 120ms delay.
When EN is returned to logic high, both devices
power down and both PG1 (tied to MR2) and RESET
return to logic low.
0.1 mF
RESET
MR1
RESET
MR1
EN
EN
>2 V
<0.7 V
V
SENSE2
SEQ
V
OUT2
V
OUT2
10 mF
EN
SEQ
V
OUT2
95%
83%
95%
83%
V
OUT1
PG1
MR1
MR2
(MR2 tied to PG1)
RESET
t1
(see Note A)
NOTE A: t1 − Time at which both V
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
and V
OUT1
Figure 36. Timing when SEQ = Low
22
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Application condition: VIN1 and VIN2 are tied to the
same fixed input voltage greater than the VUVLO; SEQ
is tied to logic high; PG1 is tied to MR2; MR1 is left
unconnected and is therefore at logic high.
TPS707xxPWP
(Fixed Output Option)
V
I
V
OUT1
V
OUT1
V
IN1
EN is initially high; therefore, both regulators are off
and PG1 and RESET are at logic low. With SEQ at
logic high, when EN is taken to logic low, VOUT2 turns
on. VOUT1 turns on after VOUT2 reaches 83% of its
regulated output voltage. When VOUT1 reaches 95%
of its regulated output voltage, PG1 (tied to MR2)
goes to logic high. When both VOUT1 and VOUT2 reach
95% of their respective regulated output voltages and
both MR1 and MR2 (tied to PG1) are at logic high,
RESET is pulled to logic high after a 120ms delay.
When EN is returned to logic high, both devices turn
off and both PG1 (tied to MR2) and RESET return to
logic low.
0.1 mF
10 mF
V
SENSE1
250 kW
PG1
MR2
MR2
V
IN2
0.1 mF
RESET
MR1
RESET
MR1
EN
EN
>2 V
V
SENSE2
<0.7 V
SEQ
V
OUT2
V
OUT2
10 mF
EN
SEQ
V
V
OUT2
95%
83%
95%
83%
OUT1
PG1
MR1
MR2
(MR2 tied to PG1)
RESET
t1
(see Note A)
NOTE A: t1 − Time at which both V and V
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
OUT1
Figure 37. Timing when SEQ = High
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
23
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Application condition: VIN1 and VIN2 are tied to the
same fixed input voltage greater than the VUVLO; SEQ
is tied to logic high; PG1 is tied to MR2; MR1 is
initially at logic high but is eventually toggled.
TPS707xxPWP
(Fixed Output Option)
V
I
V
OUT1
V
OUT1
V
IN1
EN is initially high; therefore, both regulators are off
and PG1 and RESET are at logic low. With SEQ at
logic high, when EN is taken low, VOUT2 turns on.
VOUT1 turns on after VOUT2 reaches 83% of its
regulated output voltage. When VOUT1 reaches 95%
of its regulated output voltage, PG1 (tied to MR2)
goes to logic high. When both VOUT1 and VOUT2 reach
95% of their respective regulated output voltages and
both MR1 and MR2 (tied to PG1) are at logic high,
RESET is pulled to logic high after a 120ms delay.
When MR1 is taken low, RESET returns to logic low
but the outputs remain in regulation. When MR1 is
returned to logic high, since both VOUT1 and VOUT2
remain above 95% of their respective regulated
output voltages and MR2 (tied to PG1) remains at
logic high, RESET is pulled to logic high after a
120ms delay.
0.1 mF
10 mF
V
SENSE1
250 kW
PG1
MR2
MR2
V
IN2
0.1 mF
RESET
RESET
MR1
MR1
2 V
EN
EN
>2 V
0.7 V
V
<0.7 V
SENSE2
SEQ
V
OUT2
V
OUT2
10 mF
EN
SEQ
V
V
95%
83%
OUT2
95%
OUT1
83%
PG1
MR1
MR2
(MR2 tied to PG1)
RESET
t1
(see Note A)
NOTE A: t1 − Time at which both V and V
120ms
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
OUT1
Figure 38. Timing when MR1 is Toggled
24
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Application condition: VIN1 and VIN2 are tied to the
same fixed input voltage greater than the VUVLO; SEQ
is tied to logic high; PG1 is tied to MR2; MR1 is left
unconnected and is therefore at logic high.
TPS707xxPWP
(Fixed Output Option)
V
I
V
OUT1
V
OUT1
V
IN1
EN is initially high; therefore, both regulators are off
and PG1 and RESET are at logic low. With SEQ at
logic high, when EN is taken low, VOUT2 turns on.
VOUT1 turns on after VOUT2 reaches 83% of its
regulated output voltage. When VOUT1 reaches 95%
of its regulated output voltage, PG1 (tied to MR2)
goes to logic high. When both VOUT1 and VOUT2 reach
95% of their respective regulated output voltages and
both MR1 and MR2 (tied to PG1) are at logic high,
RESET is pulled to logic high after a 120ms delay.
When a fault on VOUT1 causes it to fall below 95% of
its regulated output voltage, PG1 (tied to MR2) goes
to logic low, causing RESET to return to logic low.
VOUT2 remains on because SEQ is high.
0.1 mF
10 mF
V
SENSE1
250 kW
PG1
MR2
MR2
V
IN2
0.1 mF
RESET
MR1
RESET
MR1
EN
EN
>2 V
V
SENSE2
<0.7 V
SEQ
V
OUT2
V
OUT2
10 mF
EN
SEQUENCE
V
OUT2
95%
83%
95%
83%
V
OUT1
PG1
V
OUT1
faults out
MR1
MR2
(MR2 tied to PG1)
RESET
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
t1
(see Note A)
NOTE A: t1 − Time at which both V
and V
OUT1
Figure 39. Timing when VOUT1 Faults Out
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
25
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Application condition: VIN1 and VIN2 are tied to the
same fixed input voltage greater than the VUVLO; SEQ
is tied to logic high; PG1 is tied to MR2; MR1 is left
unconnected and is therefore at logic high.
TPS707xxPWP
(Fixed Output Option)
V
I
V
OUT1
V
OUT1
V
IN1
EN is initially high; therefore, both regulators are off
and PG1 and RESET are at logic low. With SEQ at
logic high, when EN is taken low, VOUT2 turns on.
VOUT1 turns on after VOUT2 reaches 83% of its
regulated output voltage. When VOUT1 reaches 95%
of its regulated output voltage, PG1 (tied to MR2)
goes to logic high. When both VOUT1 and VOUT2 reach
95% of their respective regulated output voltages and
both MR1 and MR2 (tied to PG1) are at logic high,
RESET is pulled to logic high after a 120ms delay.
When a fault on VOUT2 causes it to fall below 95% of
its regulated output voltage, RESET returns to logic
low and VOUT1 begins to power down because SEQ is
high. When VOUT1 falls below 95% of its regulated
output voltage, PG1 (tied to MR2) returns to logic low.
0.1 mF
10 mF
V
SENSE1
PG1
MR2
MR2
V
IN2
0.1 mF
RESET
RESET
MR1
MR1
EN
EN
>2 V
V
SENSE2
<0.7 V
SEQ
V
OUT2
V
OUT2
10 mF
ENABLE
SEQUENCE
V
OUT2
95%
83%
V
OUT2
faults out
95%
83%
V
OUT1
PG1
MR1
MR2
(MR2 tied to PG1)
RESET
t1
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
(see Note A)
NOTE A: t1 − Time at which both V
and V
OUT1
Figure 40. Timing when VOUT2 Faults Out
26
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Split Voltage DSP Application
Figure 41 shows a typical application where the TPS70751 is powering up a DSP. In this application, by
grounding the SEQ pin, VOUT1 (I/O) is powered up first, and then VOUT2 (core).
TPS70751 PWP
DSP
I/O
3.3 V
V
OUT1
5 V
V
IN1
10 mF
0.1 mF
250 kW
V
SENSE1
5 V
PG1
PG1
MR2
MR2
>2 V
V
IN2
250 kW
<0.7 V
0.1 mF
RESET
RESET
MR1
MR1
EN
<0.7 V
>2 V
>2 V
EN
<0.7 V
V
SENSE2
SEQ
1.8 V
Core
V
OUT2
10 mF
EN
SEQ
V
OUT2
95%
83%
(Core)
V
OUT1
(I/O)
95%
83%
PG1
RESET
t1
(see Note A)
NOTE A: t1 − Time at which both V and V
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
OUT1
Figure 41. Application Timing Diagram (SEQ = Low)
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
27
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Figure 42 shows a typical application where the TPS70751 is powering up a DSP. In this application, by pulling
up the SEQ pin, VOUT2 (core) is powered up first, and then VOUT1 (I/O).
TPS70751 PWP
DSP
I/O
5 V
3.3 V
V
OUT1
V
IN1
10 mF
0.1 mF
250 kW
V
SENSE1
5 V
PG1
PG1
MR2
MR2
MR1
V
IN2
250 kW
0.1 mF
RESET
RESET
MR1
EN
>2 V
EN
<0.7 V
V
SENSE2
SEQ
1.8 V
V
OUT2
Core
10 mF
EN
SEQ
V
OUT2
95%
83%
(Core)
95%
83%
V
OUT1
(I/O)
PG1
RESET
t1
120ms
are greater than the PG1 thresholds and MR1 is logic high.
OUT2
(see Note A)
NOTE A: t1 − Time at which both V
and V
OUT1
Figure 42. Application Timing Diagram (SEQ = High)
28
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Input Capacitor
For a typical application, an input bypass capacitor (0.1µF to 1µF) is recommended. This capacitor filters any
high-frequency noise generated in the line. For fast transient conditions where droop at the input of the LDO may
occur because of high inrush current, it is recommended to place a larger capacitor at the input as well. The size
of this capacitor depends on the output current and response time of the main power supply, as well as the
distance to the VI pins of the LDO.
Output Capacitor
As with most LDO regulators, the TPS707xx requires an output capacitor connected between OUT and GND to
stabilize the internal control loop. The minimum recommended capacitance value is 10µF and the ESR
(equivalent series resistance) must be between 50mΩ and 2.5Ω. Capacitor values 10µF or larger are acceptable,
provided the ESR is less than 2.5Ω. Solid tantalum electrolytic, aluminum electrolytic, and multilayer ceramic
capacitors are all suitable, provided they meet the requirements described above. Larger capacitors provide a
wider range of stability and better load transient response. Table 3 provides a partial listing of surface-mount
capacitors suitable for use with the TPS707xx for fast transient response application.
This information, along with the ESR graphs, is included to assist in selection of suitable capacitance for the user
application. When necessary to achieve low height requirements along with high output current and/or high load
capacitance, several higher ESR capacitors can be used in parallel to meet the guidelines above.
Table 3. Partial Listing of TPS707xx-Compatible Surface-Mount Capacitors
VALUE
22F
MANUFACTURER
Kemet
MAXIMUM ESR
345mΩ
MFR PART NO.
7495C226K0010AS
10TPA33M
33F
Sanyo
100mΩ
47F
Sanyo
100mΩ
6TPA47M
68F
Sanyo
45mΩ
10TPC68M
ESR and Transient Response
LDOs typically require an external output capacitor for stability. In fast transient response applications, capacitors
are used to support the load current while the LDO amplifier is responding. In most applications, one capacitor is
used to support both functions.
Besides its capacitance, every capacitor also contains parasitic impedances. These parasitic impedances are
resistive as well as inductive. The resistive impedance is called equivalent series resistance (ESR), and the
inductive impedance is called equivalent series inductance (ESL). The equivalent schematic diagram of any
capacitor can therefore be drawn as shown in Figure 43.
RESR
LESL
C
Figure 43. ESR and ESL
In most cases one can neglect the effect of inductive impedance ESL. Therefore, the following application
focuses mainly on the parasitic resistance ESR.
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
29
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
Figure 44 shows the output capacitor and its parasitic resistances in a typical LDO output stage.
Iout
LDO
+
RESR
VESR
−
Vin
Vout
RLOAD
Cout
Figure 44. LDO Output Stage with Parasitic Resistances ESR
In steady state (dc state condition), the load current is supplied by the LDO (solid arrow) and the voltage across
the capacitor is the same as the output voltage (V(CO) = VOUT). This condition means no current is flowing into the
CO branch. If IOUT suddenly increases (a transient condition), the following results occur:
•
The LDO is not able to supply the sudden current need because of its response time (t1 in Figure 45).
Therefore, capacitor CO provides the current for the new load condition (dashed arrow). CO now acts like a
battery with an internal resistance, ESR. Depending on the current demand at the output, a voltage drop
occurs at RESR. This voltage is shown as VESR in Figure 40.
•
When CO is conducting current to the load, initial voltage at the load will be VO = V(CO) – VESR. As a result of
the discharge of CO, the output voltage VO drops continuously until the response time t1 of the LDO is
reached and the LDO resumes supplying the load. From this point, the output voltage starts rising again until
it reaches the regulated voltage. This period is shown as t2 in Figure 45.
30
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
I
O
V
O
1
2
ESR 1
ESR 2
3
ESR 3
t
1
t
2
Figure 45. Correlation of Different ESRs and Their Influence on the Regulation of VO at a Load Step from
Low-to-High Output Current
Figure 45 also shows the impact of different ESRs on the output voltage. The left brackets show different levels
of ESRs where number 1 displays the lowest and number 3 displays the highest ESR.
From above, the following conclusions can be drawn:
•
•
The higher the ESR, the larger the droop at the beginning of load transient.
The smaller the output capacitor, the faster the discharge time and the greater the voltage droop during the
LDO response period.
Conclusion
To minimize the transient output droop, capacitors must have a low ESR and be large enough to support the
minimum output voltage requirement.
Programming the TPS70702 Adjustable LDO Converter
The output voltage of the TPS70702 adjustable regulators are programmed using external resistor dividers as
shown in Figure 46.
Resistors R1 and R2 should be chosen for approximately 50µA divider current. Lower value resistors can be
used, but offer no inherent advantage and waste more power. Higher values should be avoided as leakage
currents at the sense terminal increase the output voltage error. The recommended design procedure is to
choose R2 = 30.1kΩ to set the divider current at approximately 50µA, and then calculate R1 using Equation 1:
VO
Vref
R1 + ǒ Ǔ
*1 R2
(1)
where:
•
VREF = 1.224V typ (the internal reference voltage)
Copyright © 2000–2007, Texas Instruments Incorporated
Submit Documentation Feedback
31
TPS70745, TPS70748
TPS70751, TPS70758
TPS70702
www.ti.com
SLVS291D–MAY 2000–REVISED DECEMBER 2007
OUTPUT VOLTAGE
PROGRAMMING GUIDE
TPS70702
OUTPUT
V
I
R1
174
R2
169
UNIT
IN
VOLTAGE
0.1 mF
2.5 V
3.3 V
3.6 V
kW
kW
kW
>2.7 V
287
324
169
169
EN
OUT
V
O
<0.5V
+
R1
FB
GND
R2
Figure 46. TPS70702 Adjustable LDO Regulator Programming
Regulator Protection
Both TPS707xx PMOS-pass transistors have built-in back diodes that conduct reverse currents when the input
voltage drops below the output voltage (for example, during power-down). Current is conducted from the output
to the input and is not internally limited. When extended reverse voltage is anticipated, external limiting may be
appropriate.
The TPS707xx also features internal current limiting and thermal protection. During normal operation, the
TPS707xx regulator 1 limits output current to approximately 1.6A (typ) and regulator 2 limits output current to
approximately 750mA (typ). When current limiting engages, the output voltage scales back linearly until the
overcurrent condition ends. While current limiting is designed to prevent gross device failure, care should be
taken not to exceed the power dissipation ratings of the package. If the temperature of the device exceeds
+150°C (typ), thermal-protection circuitry shuts it down. Once the device has cooled below +130°C (typ),
regulator operation resumes.
Power Dissipation and Junction Temperature
Specified regulator operation is assured to a junction temperature of +125°C; the maximum junction temperature
should be restricted to +125°C under normal operating conditions. This restriction limits the power dissipation the
regulator can handle in any given application. To ensure the junction temperature is within acceptable limits,
calculate the maximum allowable dissipation, PD(max), and the actual dissipation, PD, which must be less than or
equal to PD(max)
.
The maximum-power-dissipation limit is determined using Equation 2:
TJ max *TA
PD(max)
+
RqJA
(2)
where:
•
•
TJmax is the maximum allowable junction temperature
RθJA is the thermal resistance junction-to-ambient for the package; that is, 32.6°C/W for the 20-terminal PWP
with no airflow
•
TA is the ambient temperature
The regulator dissipation is calculated using Equation 3:
ǒ
Ǔ
PD + VI*VO IO
(3)
Power dissipation resulting from quiescent current is negligible. Excessive power dissipation triggers the thermal
protection circuit.
32
Submit Documentation Feedback
Copyright © 2000–2007, Texas Instruments Incorporated
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2009
PACKAGING INFORMATION
Orderable Device
TPS70702PWP
Status (1)
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
Package Package
Pins Package Eco Plan (2) Lead/Ball Finish MSL Peak Temp (3)
Qty
Type
Drawing
HTSSOP
PWP
20
20
20
20
20
20
20
20
20
20
20
20
20
20
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPS70702PWPG4
TPS70702PWPR
TPS70702PWPRG4
TPS70745PWP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
HTSSOP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
PWP
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPS70745PWPG4
TPS70748PWP
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPS70748PWPG4
TPS70751PWP
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPS70751PWPG4
TPS70751PWPR
TPS70751PWPRG4
TPS70758PWP
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
2000 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
TPS70758PWPG4
70 Green (RoHS & CU NIPDAU Level-2-260C-1 YEAR
no Sb/Br)
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in
a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2)
Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check
http://www.ti.com/productcontent for the latest availability information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements
for all 6 substances, including the requirement that lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered
at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and
package, or 2) lead-based die adhesive used between the die and leadframe. The component is otherwise considered Pb-Free (RoHS
compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame
retardants (Br or Sb do not exceed 0.1% by weight in homogeneous material)
(3)
MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder
temperature.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
27-Aug-2009
provided. TI bases its knowledge and belief on information provided by third parties, and makes no representation or warranty as to the
accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and continues to take
reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on
incoming materials and chemicals. TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited
information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI
to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF TPS70751 :
Enhanced Product: TPS70751-EP
•
NOTE: Qualified Version Definitions:
Enhanced Product - Supports Defense, Aerospace and Medical Applications
•
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TPS70702PWPR
TPS70751PWPR
HTSSOP PWP
HTSSOP PWP
20
20
2000
2000
330.0
330.0
16.4
16.4
6.95
6.95
7.1
7.1
1.6
1.6
8.0
8.0
16.0
16.0
Q1
Q1
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
14-Jul-2012
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TPS70702PWPR
TPS70751PWPR
HTSSOP
HTSSOP
PWP
PWP
20
20
2000
2000
367.0
367.0
367.0
367.0
38.0
38.0
Pack Materials-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46C and to discontinue any product or service per JESD48B. Buyers should
obtain the latest relevant information before placing orders and should verify that such information is current and complete. All
semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale supplied at the time
of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components which meet ISO/TS16949 requirements, mainly for automotive use. Components which
have not been so designated are neither designed nor intended for automotive use; and TI will not be responsible for any failure of such
components to meet such requirements.
Products
Audio
Applications
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
www.ti.com/security
Medical
Logic
Security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense www.ti.com/space-avionics-defense
microcontroller.ti.com
www.ti-rfid.com
Video and Imaging
www.ti.com/video
OMAP Mobile Processors www.ti.com/omap
Wireless Connectivity www.ti.com/wirelessconnectivity
TI E2E Community
e2e.ti.com
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2012, Texas Instruments Incorporated
相关型号：
TPS70751
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TI
TPS70751-EP
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATOR WITH POWER-UP SEQUENCING FOR SPLIT-VOLTAGE DSP SYSTEMS
TI
TPS70751MPWPREP
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATOR WITH POWER-UP SEQUENCING FOR SPLIT-VOLTAGE DSP SYSTEMS
TI
TPS70751PWP
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TI
TPS70751PWPG4
Dual-Output, Low Dropout Voltage Regulators with Power-Up Sequencing for Split-Voltage DSP Systems 20-HTSSOP -40 to 125
TI
TPS70751PWPR
250-mA, dual-channel low-dropout voltage regulator with power good & enable 20-HTSSOP -40 to 125
TI
TPS70758
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TI
TPS70758PWP
DUAL-OUTPUT LOW-DROPOUT VOLTAGE REGULATORS WITH POWER UP SEQUENCING FOR SPLIT VOLTAGE DSP SYSTEMS
TI
©2020 ICPDF网 联系我们和版权申明