TUSB1002A [TI]
USB3.2 10Gbps 双通道线性转接驱动器;型号: | TUSB1002A |
厂家: | TEXAS INSTRUMENTS |
描述: | USB3.2 10Gbps 双通道线性转接驱动器 驱动 驱动器 |
文件: | 总36页 (文件大小:3060K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Support &
Community
Product
Folder
Order
Now
Tools &
Software
Technical
Documents
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
TUSB1002A USB3.2 10Gbps 双通道线性转接驱动器
1 特性
3 说明
1
•
支持 USB3.2 x1 SuperSpeed (5Gbps) 和
SuperSpeedPlus (10Gbps)
TUSB1002A 是业内首款双通道 USB 3.2 x1
SuperSpeedPlus (SSP) 转接驱动器和信号调节器。该
器件采用超低功耗架构,由 3.3V 电源供电,具有很低
的功耗。它支持 USB3.2 低功耗模式,可进一步降低
空闲状态下的功耗。
•
•
支持 PCI Express Gen3、SATA Express 和 SATA
Gen3。
超低功耗架构
–
–
–
活动:<300mW
TUSB1002A 实现了一款线性均衡器,最高可容许码间
串扰 (ISI) 引入 16dB 的损耗。当 USB 信号在印刷电
路板 (PCB) 或电缆上传输时,其完整性会在通道损耗
和码间串扰的影响下有所降低。线性均衡器可对通道损
失进行补偿,进而延长通道传输距离,从而使系统符合
USB 规范。凭借双通道和小型封装,TUSB1002A 可
在 USB3.2 路径中灵活放置。
断开/U2/U3:< 1.9mW
关断:< 700µW
•
•
•
•
•
•
可调节电压输出摆幅线性范围高达 1200 mVpp
无主机/设备端要求
16 种线性均衡设置,高达 16dB(10Gbps 时)
可调节直流均衡增益
支持热插拔
TUSB1002A 采用 24 引脚 4mm x 4mm VQFN 封装。
它还具有商业级 (TUSB1002A) 和工业级
(TUSB1002AI) 两个版本。
与 LVPE502A 和 LVPE512 USB 3.0 转接驱动器引
脚兼容
•
•
与 TUSB1002 转接驱动器引脚对引脚兼容
温度范围:0°C 至 70°C(商业级)和 –40°C 至
85°C(工业级)
器件信息(1)
器件编号
TUSB1002A
TUSB1002AI
封装
封装尺寸(标称值)
•
•
•
±5kV HBM ESD
由 3.3V 单电源供电。
采用 4mm x 4mm VQFN 封装
VQFN (24)
4.00mm x 4.00mm
(1) 如需了解所有可用封装,请参阅产品说明书末尾的可订购产品
附录。
2 应用
•
•
•
•
•
•
笔记本和台式机
电视
平板电脑
手机
有源电缆
扩展坞
空白
简化原理图
RXP1
+
RXN1
-
TXP1
TXN1
+
-
+
-
TUSB1002A
+
USB 3.1
Host
TXP2
TXN2
RXP2
RXN2
+
-
+
-
-
1
本文档旨在为方便起见,提供有关 TI 产品中文版本的信息,以确认产品的概要。 有关适用的官方英文版本的最新信息,请访问 www.ti.com,其内容始终优先。 TI 不保证翻译的准确
性和有效性。 在实际设计之前,请务必参考最新版本的英文版本。
English Data Sheet: SLLSF63
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
目录
7.5 U0 Mode.................................................................. 18
7.6 U1 Mode.................................................................. 18
7.7 U2/U3 Mode............................................................ 18
Application and Implementation ........................ 19
8.1 Application Information............................................ 19
8.2 Typical USB3.2 Application .................................... 19
1
2
3
4
5
6
特性.......................................................................... 1
应用.......................................................................... 1
说明.......................................................................... 1
修订历史记录 ........................................................... 2
Pin Configuration and Functions......................... 3
Specifications......................................................... 5
6.1 Absolute Maximum Ratings ...................................... 5
6.2 ESD Ratings.............................................................. 5
6.3 Recommended Operating Conditions....................... 5
6.4 Thermal Information.................................................. 5
6.5 Electrical Characteristics........................................... 6
6.6 Timing Requirements................................................ 9
6.7 Switching Characteristics.......................................... 9
6.8 Typical Characteristics............................................ 11
Detailed Description ............................................ 14
7.1 Overview ................................................................. 14
7.2 Functional Block Diagram ....................................... 14
7.3 Feature Description................................................. 15
7.4 Device Functional Modes........................................ 18
8
9
8.3 Typical SATA, PCIe and SATA Express
Application................................................................ 22
Power Supply Recommendations...................... 25
10 Layout................................................................... 25
10.1 Layout Guidelines ................................................. 25
10.2 Layout Example .................................................... 26
11 器件和文档支持 ..................................................... 27
11.1 接收文档更新通知 ................................................. 27
11.2 社区资源................................................................ 27
11.3 商标....................................................................... 27
11.4 静电放电警告......................................................... 27
11.5 术语表 ................................................................... 27
12 机械、封装和可订购信息....................................... 27
7
4 修订历史记录
Changes from Original (March 2018) to Revision A
Page
•
•
Changed text From: "Inclusion of these 330nF capacitors and 220k resistors is optional but highly recommended."
To: "Inclusion of the 330 nF capacitors and 220k resistors is optional." in the Detailed Design Procedure........................ 20
Added ordered list of implementation options for USB connector to TUSB1002A RX pins ................................................ 20
2
Copyright © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
5 Pin Configuration and Functions
RGE Package
24-Pin VQFN
Top View
VCC
CH1_EQ1
CH1_EQ2
CFG1
1
2
3
4
5
6
18
17
16
15
14
13
GND
CH2_EQ2
CH2_EQ1
CFG2
Thermal
Pad
EN
DCBOOST#
VCC
GND
Not to scale
Pin Functions
PIN
INTERNAL PULLUP
PULLDOWN
TYPE
DESCRIPTION
NAME
NO.
Differential input for SuperSpeed (SS) and SuperSpeedPlus (SSP) positive
signals for Channel 1
RX1P
9
90Ω Differential
Input
Differential input for SuperSpeed (SS) and SuperSpeedPlus (SSP) negative
signals for Channel 1
RX1N
RX2P
RX2N
TX1P
TX1N
TX2P
TX2N
8
Differential input for SuperSpeed (SS) and SuperSpeedPlus (SSP) positive
signals for Channel 2
19
20
22
23
12
11
90Ω Differential
Input
Differential input for SuperSpeed (SS) and SuperSpeedPlus (SSP) negative
signals for Channel 2.
Differential output for SuperSpeed (SS) and SuperSpeedPlus (SSP) positive
signals for Channel 1.
90Ω Differential
Output
Differential output for SuperSpeed (SS) and SuperSpeedPlus (SSP) negative
signals for Channel 1.
Differential output for SuperSpeed (SS) and SuperSpeedPlus (SSP) positive
signals for Channel 2.
90Ω Differential
Output
Differential output for SuperSpeed (SS) and SuperSpeedPlus (SSP) negative
signals for Channel 2.
CH1_EQ1. Configuration pin used to control Rx EQ level for RX1P/N. The state
of this pin is sampled after the rising edge of EN. Refer to 图 2 for details of
timing. This pin along with CH1_EQ2 allows for up to 16 equalization settings.
CH1_EQ1
CH1_EQ2
CH2_EQ1
CH2_EQ2
EN
2
3
I (4-level)
I (4-level)
I (4-level)
I (4-level)
I (2-level)
CH1_EQ2. Configuration pin used to control Rx EQ level for RX1P/N. The state
of this pin is sampled after the rising edge of EN. Refer to 图 2 for details of
timing. This pin along with CH1_EQ1 allows for up to 16 equalization settings.
PU (approx 45K)
PD (approx 95K)
CH2_EQ1. Configuration pin used to control Rx EQ level for RX2P/N. The state
of this pin is sampled after the rising edge of EN. Refer to 图 2 for details of
timing. This pin along with CH2_EQ2 allows for up to 16 equalization settings.
16
17
5
CH2_EQ2. Configuration pin used to control Rx EQ level for RX2P/N. The state
of this pin is sampled after the rising edge of EN. Refer to 图 2 for details of
timing. This pin along with CH2_EQ1 allows for up to 16 equalization settings.
EN. Places TUSB1002A into shutdown mode when asserted low. Normal
operation when pin is asserted high. When in shutdown, TUSB1002A’s receiver
terminations will be high impedance and tx/rx channels will be disabled.
PU (approx 400 K)
Copyright © 2018, Texas Instruments Incorporated
3
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Pin Functions (continued)
PIN
INTERNAL PULLUP
TYPE
DESCRIPTION
PULLDOWN
NAME
NO.
CFG1. This pin along with CFG2 will select VOD linearity range and DC gain
for both channels 1 and 2. The state of this pin is sampled after the rising edge
of EN. Refer to 图 2 for details of timing. Refer to 表 3 for VOD linearity range
and DC gain options.
PU (approx 45K)
PD (approx 95K)
CFG1
4
I (4-level)
CFG2. This pin along with CFG1 will set VOD linearity range and DC gain for
both channels 1 and 2. The state of this pin is sampled after the rising edge of
EN. Refer to 图 2 for details of timing. Refer to 表 3 for VOD linearity range and
DC gain options.
PU (approx 45K)
PD (approx 95K)
CFG2
15
I (4-level)
MODE. This pin is for selecting different modes of operation. The state of this
pin is sampled after the rising edge of EN. Refer to 图 2 for details of timing.
0 = Basic Redriver Mode.
R = PCIe / Test Mode. PCIe Mode and TI Internal use only
F = USB3.2 x1 Dual Channel Operation enabled (TUSB1002A normal mode).
1 = USB3.2 x1 Single-channel operation.
PU (approx 45 K)
PD (approx 95K)
MODE
7
I (4-level)
RSVD1. Under normal operation, this pin will be driven low by TUSB1002A.
Recommend leaving this pin unconnected on PCB.
RSVD1
24
O
DCBOOST#. This pin when asserted low will increase the DC Gain level
defined in表 3 by +1 dB unless already at +2dB. If DC Gain level defined in表 3
is already at +2 dB, then asserting this pin low will not change the DC Gain
level. This pin can be left unconnected if this function is not needed.
1 = DC Gain defined by 表 3.
DCBOOST#
14
I (2-level)
PU (approx 400 K)
0 = DC Gain defined by 表 3 is increased by +1 dB.
VCC
GND
1, 13
Power
GND
3.3 V (±10%) Supply.
Ground
6, 10, 18,
21
Thermal
pad
Thermal pad. Recommend connecting to a solid ground plane.
4
Copyright © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
6 Specifications
6.1 Absolute Maximum Ratings
over operating free-air temperature range (unless otherwise noted)(1)
MIN
MAX
UNIT
Supply Voltage
VCC
-0.3
4
V
Range
Differential voltage for RX1P/N and RX2P/N
Voltage Range
Voltage at RX pins
on I/O pins
-2.5
-0.5
-0.5
-65
2.5
4
V
V
Voltage on Control pins
4
V
Tstg
Storage temperature
150
°C
(1) Stresses beyond those listed under Absolute Maximum Rating may cause permanent damage to the device. These are stress ratings
only, which do not imply functional operation of the device at these or any other conditions beyond those indicated under Recommended
Operating Condition. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
6.2 ESD Ratings
VALUE
UNIT
Human body model (HBM), per
±5000
ANSI/ESDA/JEDEC JS-001, all pins(1)
V(ESD)
Electrostatic discharge
V
Charged device model (CDM), per JEDEC
specification JESD22-C101, all pins(2)
±1500
(1) JEDEC document JEP155 states that 500-V HBM allows safe manufacturing with a standard ESD control process.
(2) JEDEC document JEP157 states that 250-V CDM allows safe manufacturing with a standard ESD control process.
6.3 Recommended Operating Conditions
over operating free-air temperature range (unless otherwise noted)
MIN
NOM
MAX
3.6
UNIT
V
VCC
Supply voltage
3
3.3
VPSN
Supply noise on VCC pins
100
70
mV
°C
TUSB1002A Ambient temperature
TUSB1002AI Ambient temperature
TUSB1002A Junction temperature
TUSB1002AI Junction temperature
0
-40
0
TA
TJ
85
°C
105
105
°C
-40
°C
6.4 Thermal Information
TUSB1002A
THERMAL METRIC(1)
RGE (VQFN)
24 PINS
38.5
UNIT
RθJA
Junction-to-ambient thermal resistance
Junction-to-case (top) thermal resistance
Junction-to-board thermal resistance
°C/W
°C/W
°C/W
°C/W
°C/W
°C/W
RθJC(top)
RθJB
41.6
16.3
ΨJT
Junction-to-top characterization parameter
Junction-to-board characterization parameter
Junction-to-case (bottom) thermal resistance
1.0
ΨJB
16.4
RθJC(bot)
6.9
(1) For more information about traditional and new thermal metrics, see the Semiconductor and IC Package Thermal Metrics application
report.
版权 © 2018, Texas Instruments Incorporated
5
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
6.5 Electrical Characteristics
over operating free-air temperature and voltage range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
POWER
Power under USB3.1
operation in U0 operating at
SuperSpeedPlug datarate
with linear range set to
1200mV.
At 10 Gbps; VCC = 3.3 V; EN = 1; Pattern
= CP9; VOD = 1200mVpp
PU0_SSP_1200mV
330
mW
Power under USB3.1
operation in U0 operating at
SuperSpeedPlug datarate
with linear range set to
1000mV.
At 10 Gbps; VCC = 3.3 V; EN = 1; Pattern
= CP9; VOD = 1000mVpp
PU0_SSP_1000mV
310
295
mW
mW
Power under USB3.1
operation in U0 operating at
SuperSpeedPlug datarate
with linear range set to
900mV.
At 10 Gbps; VCC = 3.3 V; EN = 1; Pattern
= CP9; VOD = 900mVpp
PU0_SSP_900mV
Power in U1 with linear range In U1; VCC = 3.3 V; EN = 1; VOD
=
PU1
330
1.5
mW
mW
set to 1200mV.
1200mVpp
VCC = 3.3 V; EN = 1; Both channels in
U2/U3;
PU2U3
Power when in U2/U3 state.
Power when no USB device
PDISCONNECT_NONE detected on both TX1P/N and
TX2P/N.
VCC = 3.3 V; EN = 1; RX1 and RX2
termination disabled;
1.9
mW
Power when a single USB
device detected on either
TX1P/N or TX2P/N.
VCC = 3.3 V; EN = 1; Either RX1 or RX2
termination enabled but not both enabled;
PDISCONNECT_ONE
1.9
0.7
mW
mW
Shutdown power when EN =
0.
PSHUTDOWN
VCC = 3.3 V; EN = 0;
4-level Inputs (CFG[2:1], MODE, CH1_EQ[2:1], CH2_EQ[2:1])
Threshold "0" / "R"
VCC = 3.3 V
0.55
1.65
2.8
V
V
VTH
Threshold "R" / "F"
VCC = 3.3 V
Threshold "F" / "1"
VCC = 3.3 V
V
IIH
High-level input current
Low-level input current
Internal pullup resistance
Internal pulldown resistance
VCC = 3.6 V; VIN = 3.6 V
VCC = 3.6 V; VIN = 0 V
20
80
µA
µA
kΩ
kΩ
IIL
-160
-40
RPU
45
95
RPD
EN, DCBOOST#
VIH
VIL
IIH
High-level input voltage
Low-level input voltage
High-level input current
Low-level input current
VCC = 3.3 V
1.7
0
3.6
0.7
10
V
V
VCC = 3.3 V
VCC = 3.6 V; VIN = 3.6 V
VCC = 3.6 V; VIN = 0 V
-10
-15
µA
µA
IIL
15
Internal pullup resistance for
EN and DCBOOST#
RPU_EN
400
kΩ
USB3.1 Receiver Interface (RX1P/N and RX2P/N)
Rx Differential return loss at
RL_100 MHz
SDD11 100 MHz to 2.5 GHz at 90-ohms
SDD11 5 GHz at 90-ohms
-18
-14
dB
dB
100 MHz to 2.5 GHz
Rx Differential return loss at 5
RL_5 GHz
GHz
Rx Differential return loss from
5 to 10 GHz
RL_10 GHz
SDD11 5 GHz to 10 GHz at 90-ohms
-6
-12
-50
16
dB
dB
dB
dB
RL_CM
Rx common mode return loss SCC11 0.5 to 5 GHz at 90-ohms
Differential crosstalk between
TX and RX signal pairs
X-Talk
EACGAIN_5 GHz
Max AC Equalization Gain
50 mVpp CP10 at 5 GHz; VCC = 3.3V;
6
Copyright © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
Electrical Characteristics (continued)
over operating free-air temperature and voltage range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
200 mVpp VID at 100 MHz; 1200mV
Linear Range Setting;
EDC_GAIN0
EDC_GAIN1
EDC_GAIN2
EDC_GAIN-1
DC Gain at 0 dB setting
.7
dB
200 mVpp VID at 100 MHz; 1200mV
Linear Range Setting;
DC Gain at 1 dB setting
DC Gain at 2 dB setting
DC Gain at -1 dB setting
1.6
2.3
dB
dB
dB
200 mVpp VID at 100 MHz; 1000mV
Linear Range Setting;
200 mVpp VID at 100 MHz; 1200mV
Linear Range Setting;
-0.25
Input differential peak-peak
voltage swing range
VDIFF_IN
1200
0
mV
V
VRX-DC-CM
RRX-DC-CM
RRX-DC-DIFF
RX DC common mode voltage
RX DC common mode
impedance
Measured at connector; Present when
USB Device detected on TXP/N;
18
72
30
Ω
Measured at connector; Present when
USB Device detected on TXP/N;
RX DC differential impedance
120
Ω
1. Rx DC CM Impedance with Rx
DC Input CM Input Impedance terminations not powered. 2. Measured
V > 0 during RESET or power over the range 0 - 500 mV with respect to
ZRX-DC-DIFF
35
kΩ
mV
down.
GND. 3. Only DC input CM Input
impedance V > 0 is specified.
Input differential peak-to-peak At 10 Gbps; No loss input channel and
signal detect assert level PRBS7 pattern.
VRX-SIGNAL-DET
85
60
Input differential peak-to-peak At 10 Gbps; No loss input channel and
VRX-IDLE-DET
VRX-LFPS-DET
VRX-CM-AC-P
mV
mV
mV
signal detect de-assert level
PRBS7 pattern.
LFPS detect threshold.
Below min is squelched
100
310
150
Peak RX AC common mode
voltage
Measured at package pin.
USB3.1 Transmitter Interface (TX1P/N and TX2P/N)
Tx Differential return loss at
RL_TX_100 MHz
100 MHz
SDD22 100 MHz - 2.5 GHz at 90-ohms
SDD22 5 GHz at 90-ohms
-20
-16
dB
dB
dB
Tx Differential return loss at 5
GHz
RL_TX_2.5 GHz
Tx Differential return loss from
RL_TX_10 GHz
5 to 10 GHz
SDD22 5 GHz to 10 GHz at 90-ohms
-8.5
RL_TX_CM
Tx common mode return loss SCC22 0.5 to 5 GHz at 90-ohms
-6.7
dB
VTX-DIFFPP-1200
Differential peak-to-peak TX
voltage swing linear dynamic
range at 100MHz
1200 mVpp setting; 100MHz; Measured
at -1dB compression point = 20
log(VOD/VOD_linear)
1000
mV
Differential peak-to-peak TX
voltage swing linear dynamic
range at 5GHz
1200 mVpp setting; 5GHz; Measured at
-1dB compression point = 20
log(VOD/VOD_linear)
1300
900
mV
mV
mV
mV
Differential peak-to-peak TX
voltage swing linear dynamic
range at 100MHz
1000 mVpp setting; 100MHz; Measured
at -1dB compression point = 20
log(VOD/VOD_linear)
VTX-DIFFPP-1000
Differential peak-to-peak TX
voltage swing linear dynamic
range at 5GHz
1000 mVpp setting; 5GHz; Measured at
-1dB compression point = 20
log(VOD/VOD_linear)
1150
800
Differential peak-to-peak TX
voltage swing linear dynamic
range at 100MHz
900 mVpp setting; 100MHz; Measured at
-1dB compression point = 20
log(VOD/VOD_linear)
VTX-DIFFPP-900
Differential peak-to-peak TX
voltage swing linear dynamic
range at 5GHz
900 mVpp setting; 5GHz; Measured at
-1dB compression point = 20
log(VOD/VOD_linear)
1000
mV
mV
Amount of voltage change
allowed during Rx Detection.
VTX-RCV-DETECT
Measured at package pins.
600
Copyright © 2018, Texas Instruments Incorporated
7
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Electrical Characteristics (continued)
over operating free-air temperature and voltage range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
-600
0
TYP
MAX
UNIT
mV
V
Max allowed instantaneous commode-
mode voltage at connector side of AC
coupling capacitor. This is an absolute
voltage spec referenced to the receive
side termination ground.
Transmitter idle common
mode voltage change U2/U3
state.
VTX-CM-IDLE-DELTA
600
2.05
116
VTX-DC-CM
TX DC common mode voltage 1200mVpp linear range setting;
1.85
Transmitter AC common
mode peak-peak voltage in
VTX-CM-AC-PP-ACTIVE U0. Maximum mismatch from setting matches input channel insertion
1200mVpp linear setting; CHx_EQ
mV
TXP+TXN for both time and
amplitude.
loss;
AC electrical idle differential
peak-to-peak output voltage
VTX-IDLE-DIFF-AC-PP
0
10
mV
mV
VTX-CM-DC-ACTIVE-
IDLE-DELTA
Absolute DC common mode
voltage between U1 and U0
200
TX DC common mode
impedance
RTX-DC-CM
RTX-DC-DIFF
ITX-SHORT
18
72
30
120
107
Ω
Ω
TX DC differential impedance
Transmitter short-circuit
current limit.
mA
External AC coupling
capacitor on differential pairs.
CAC-COUPLING
75
265
nF
8
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
6.6 Timing Requirements
over operating free-air temperature and voltage range (unless otherwise noted)
MIN
NOM
MAX
UNIT
µs
td_pg
Internal power good asserted high when VCC is at 2.5V
CFG(1) pins setup before internal Reset(2) high
CFG(1) pins hold after internal Reset(2) high
5
tCFG_SU
tCFG_HD
0
500
0.1
µs
µs
tVCC_RAMP VCC supply ramp requirement
50
ms
(1) Following pins comprise CFG pins: MODE, CFG[2:1], CH1_EQ[2:1], CH2_EQ[2:1]
(2) Internal reset is the logical AND of EN pin and internal power good.
6.7 Switching Characteristics
over operating free-air temperature and voltage range (unless otherwise noted)
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNIT
tIDLEEntry
Delay from U0 to electrical idle
VCC = 3.0 V; EN = 1;See 图 1
150
ps
U1 exit time. Break in electrical idle
to transmission of LFPS.
tIDLEEntry_U1
VCC = 3.0 V; EN = 1; See 图 1
150
ps
tIDLEEntry_U2 U2/U3 exit time; Break in electrical
VCC = 3.0 V; EN = 1; See 图 1
6
µs
ps
idle to transmission of LFPS
U3
tDIFF_DLY
Differential propagation delay
VCC = 3.0 V; EN = 1;
150
Time from assertion of EN to device
active and performing Rx.Detect on
both ports
tPWRUP_ACTI
VE
VCC = 3.0 V; EN = 1;
8
ms
ps
ps
UI
VCC = 3.3 V; EN = 1; 10 Gbps; 20% to
80% of differential output; 1200 mVpp
linear range setting; Fast Input rise/fall
time;
tTX_RISE_FAL
L
Transmitter rise/fall time
27
.6
VCC = 3.3 V; EN = 1; 10 Gbps; 20% to
80% of differential output; 1200 mVpp
linear range setting; 1000 mVpp VID
tRF_MISMATC
H
Transmitter rise/fall mismatch
VCC = 3.3 V; EN = 1; 10 Gbps; 1200
mVpp linear range setting; Input channel
loss of 12 dB; Output channel loss of 1.5
dB; Optimized EQ;
Transmitter residual deterministic
jitter
tTX_DJ
0.05
图 1. Idle Entry and Exit Latency
版权 © 2018, Texas Instruments Incorporated
9
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
图 2. Power-Up Diagram
10
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
6.8 Typical Characteristics
VCC = 3.3V , 25°C, 200 mVpp VID sine wave, ZO = 100 Ω, RGE package
20
15
10
5
20
15
10
5
EQ1_DC0_1200 mV
EQ3_DC0_1200 mV
EQ5_DC0_1200 mV
EQ7_DC0_1200 mV
EQ9_DC0_1200 mV
EQ11_DC0_1200 mV
EQ13_DC0_1200 mV
EQ15_DC0_1200 mV
EQ2_DC0_1200 mV
EQ4_DC0_1200 mV
EQ6_DC0_1200 mV
EQ8_DC0_1200 mV
EQ10_DC0_1200 mV
EQ12_DC0_1200 mV
EQ14_DC0_1200 mV
EQ16_DC0_1200 mV
0
0
-5
-5
0.01
0.1
1
10 20
0.01
0.1
1
10 20
Frequency (GHz)
Frequency (GHz)
D003
D004
图 3. 1200 mV DC0 Gain Odd EQ Settings Curves
图 4. 1200 mV DC0 Even EQ Settings Curves
7
5
20
15
10
5
EQ1_DC-1_1200 mV
EQ1_DC2_1200 mV
EQ1_DC0_1200 mV
EQ1_DC1_1200 mV
EQ1_DC0_1000 mV
EQ3_DC0_1000 mV
EQ5_DC0_1000 mV
EQ7_DC0_1000 mV
EQ9_DC0_1000 mV
EQ11_DC0_1000 mV
EQ13_DC0_1000 mV
EQ15_DC0_1000 mV
3
1
-1
-3
-5
0
-5
0.01
0.1
1
10
0.01
0.1
1
10 20
Frequency (GHz)
Frequency (GHz)
D005
D006
图 5. 1200 mV DC Gain Adjustments Curves
图 6. 1000 mV DC0 Gain Odd EQ Settings Curves
20
15
10
5
7
5
EQ2_DC0_1000 mV
EQ4_DC0_1000 mV
EQ6_DC0_1000 mV
EQ8_DC0_1000 mV
EQ10_DC0_1000 mV
EQ12_DC0_1000 mV
EQ14_DC0_1000 mV
EQ16_DC0_1000 mV
EQ1_DC0_1000 mV
EQ1_DC1_1000 mV
EQ1_DC2_1000 mV
EQ1_DC-1_1000 mV
3
1
-1
-3
-5
0
-5
0.01
0.1
1
10 20
0.01
0.1
1
10
Frequency (GHz)
Frequency (GHz)
D007
D008
图 7. 1000 mV DC0 Gain Even EQ Settings Curves
图 8. 1000 mV DC Gain Adjustments Curves
版权 © 2018, Texas Instruments Incorporated
11
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
Typical Characteristics (接下页)
VCC = 3.3V , 25°C, 200 mVpp VID sine wave, ZO = 100 Ω, RGE package
20
15
10
5
20
15
10
5
EQ1_DC0_900 mV
EQ3_DC0_900 mV
EQ5_DC0_900 mV
EQ7_DC0_900 mV
EQ9_DC0_900 mV
EQ11_DC0_900 mV
EQ13_DC0_900 mV
EQ15_DC0_900 mV
EQ2_DC0_900 mV
EQ4_DC0_900 mV
EQ6_DC0_900 mV
EQ8_DC0_900 mV
EQ10_DC0_900 mV
EQ12_DC0_900 mV
EQ14_DC0_900 mV
EQ16_DC0_900 mV
0
0
-5
-5
0.01
0.1
1
10 20
0.01
0.1
1
10 20
Frequency (GHz)
Frequency (GHz)
D009
D010
图 9. 900 mV DC0 Gain Odd EQ Settings Curves
图 10. 900 mV DC0 Gain Even EQ Settings Curves
7
5
1
EQ1_DC0_900 mV
EQ1_DC1_900 mV
-1
-3
-5
-7
3
-9
-11
-13
-15
-17
-19
-21
-23
-25
1
-1
-3
-5
0.01
0.1
1
10
0.01
0.1
1
10
Frequency (GHz)
Frequency (GHz)
D011
D012
图 11. 900 mV DC Gain Adjustment Curves
图 12. SDD11 Return Loss
0
-5
1800
1600
1400
1200
1000
800
-10
-15
-20
-25
600
400
DC0_EQ1_900 mV
DC0_EQ1_1000 mV
DC0_EQ1_1200 mV
200
0
0.01
0.1
1
10 20
0
200
400
600
800
1000 1200 14001500
Frequency (GHz)
VID (mV)
D013
D014
图 13. SDD22 Return Loss
图 14. 5-GHz Sine Wave VID vs VOD Linearity Range Setting
12
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
Typical Characteristics (接下页)
VCC = 3.3V , 25°C, 200 mVpp VID sine wave, ZO = 100 Ω, RGE package
1400
1200
1000
800
600
400
200
0
DC0_EQ1_900mV
DC0_EQ1_1000mV
DC0_EQ1_1200mV
0
200 400 600 800 1000 1200 1400 1600 1800 2000
VID (V)
D015
图 15. 100-MHz Sine Wave VID vs VOD Linearity Range Setting
版权 © 2018, Texas Instruments Incorporated
13
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
7 Detailed Description
7.1 Overview
The TUSB1002A is the industry’s first, dual lane USB 3.2 x1 SuperSpeedPlus redriver. As signals traverse
through a channel (like FR4 trace) the amplitude of the signal is attenuated. The attenuation varies depending on
the frequency content of the signal. Depending the length of the channel this attenuation could be large enough
resulting in signal integrity issues at a USB 3.2 receiver. By placing a TUSB1002A between USB3.2 host and
device the attenuation effect of the channel can eliminated or minimized. The result is a USB3.2 compatible eye
at the devices receiver. With up to 16 receiver equalization settings, the TUSB1002A can support many different
channel loss combinations. The TUSB1002A offers low power consumption on a single 3.3 V supply with its ultra
low power architecture. It supports the USB3.2 low power modes which further reduces idle power consumption.
The TUSB1002A settings are configured through pins. In addition to equalization adjustment, the TUSB1002A
provides knobs for adjusting DC gain and voltage output linearity range.
7.2 Functional Block Diagram
GND
VIterm
ARXTERM_EN1
RX1P
RX1N
TX1P
TX1N
TX
RX
ATXEN1
AIDLE1
LFPS
ALFPS1
Rx
ARXDET1
Detect
ALOSZ1
LOS
GND
VIterm
ARXTERM_EN2
RX
TX2P
RX2P
RX2N
TX
TX2N
ATXEN2
AIDLE2
LFPS
ALFPS2
Rx
Detect
ARXDET2
ALOSZ2
LOS
CFG1
CH1_EQ1
CH1_EQ2
CFG2
CH2_EQ1
CH2_EQ2
MODE
Digital
FSM
DCBOOST#
RSVD1
EN
14
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
7.3 Feature Description
7.3.1 4-Level Control Inputs
The TUSB1002A has (MODE, CFG1, CFG2, CH1_EQ1, CH1_EQ2, CH2_EQ1, and CH2_EQ2) 4-level inputs
pins that are used to control the equalization gain and the output voltage swing dynamic range. These 4-level
inputs use a resistor divider to help set the 4 valid levels and provide a wider range of control settings. These
resistors together with the external resistor connection combine to achieve the desired voltage level.
表 1. 4-Level Control Pin Settings
LEVEL
SETTINGS
Option 1: Tie 1 kΩ 5% to GND.
Option 2: Tie directly to GND.
0
R
F
Tie 20 kΩ 5% to GND.
Float (leave pin open)
Option 1: Tie 1 kΩ 5% to VCC
.
1
Option 2: Tie directly to VCC
.
注
In order to conserve power, the TUSB1002A disables 4-level input’s internal pull-up/pull-
down resistors after the state of 4-level pins have been sampled on rising edge of EN. A
change of state for any four level input pin is not applied to TUSB1002A until after EN pin
transitions from low to high.
7.3.2 Linear Equalization
With a linear equalizer, the TUSB1002A can electrically shorten a particular channel allowing for longer run
lengths.
X in trace
USB
Type A
USB Host
Y in trace
X in trace
USB
Type A
TUSB1002A
USB Host
图 16. Linear Equalizer
With a TUSB1002A, a longer trace can be made to have similar insertion loss as a shorter trace. For example, a
long trace of X + Y inches can be made to have similar loss characteristics of a shorter trace of X inches.
The receiver equalization level for each channel is determined by the state of the CHx_EQ1 and CHx_EQ2 pins,
where x = 1 or 2.
版权 © 2018, Texas Instruments Incorporated
15
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
表 2. EQ Configuration Options for 1200mV Linearity 0 dB DC Gain Setting
EQ SETTING #
CHx_EQ2 PIN LEVEL
CHx_EQ1 PIN LEVEL
EQ GAIN at 2.5GHz / 5 GHz (dB)
1.0 / 3.6
1
2
0
0
0
R
F
1
2.1 / 5.5
3
0
3.0 / 6.8
4
0
4.0 / 8.1
5
R
R
R
R
F
F
F
F
1
0
4.6 / 9.0
6
R
F
1
5.5 / 10.0
7
6.2 / 10.8
8
6.9 / 11.6
9
0
7.3 / 11.9
10
11
12
13
14
15
16
R
F
1
7.9 / 12.6
8.4 / 13.1
9.0 / 13.7
0
9.4 / 14.1
1
R
F
1
9.9 / 14.6
1
10.3 / 14.9
10.7 / 15.3
1
7.3.3 Adjustable VOD Linear Range and DC Gain
The CFG1 and CFG2 pins can be used to adjust the TUSB1002A output voltage swing linear range and receiver
equalization DC gain. 表 3 details the available options.
For best performance, the TUSB1002A should be operated within its defined VOD linearity range. The gain of
the incoming VID should be kept to less than or equal to the TUSB1002A VOD linear range setting. The can be
determined by 公式 1:
VID at 5 GHz = VOD x (10 -(Gv/20)
)
where
•
Gv = TUSB1002A Gain and VOD = TUSB1002A VOD linearity setting.
(1)
For example, for a VOD linearity range setting of 1200 mV, the maximum incoming VID signal at 5 GHz with a
CHx_EQ[1:0] setting of 2 (5.5 dB) is 1200 x (10 -(5.5/20)) = 637 mVpp. The TUSB1002A can be operated outside
its VOD linear range but jitter will be higher.
表 3. VOD Linear Range and DC Gain
CH1 VOD LINEAR
RANGE (mVpp)
CH2 VOD LINEAR
RANGE (mVpp)
SETTING #
CFG1 PIN LEVEL
CFG2 PIN LEVEL
CH1 DC GAIN (dB) CH2 DC GAIN (dB)
1
2
0
0
0
R
F
1
+1
0
0
+1
0
900
900
900
900
3
0
0
900
900
4
0
+1
0
+1
0
900
900
5
R
R
R
R
F
F
F
F
1
0
1000
1000
1000
1000
1200
1200
1200
1200
1200
1200
1200
1200
1000
1000
1000
1000
1200
1200
1200
1200
1200
1200
1200
1200
6
R
F
1
+1
0
0
7
-1
+2
-1
+2
0
8
+2
-1
+2
0
9
0
10
11
12
13
14
15
16
R
F
1
+1
+2
0
+1
0
0
1
R
F
1
+2
+1
0
1
0
1
+1
16
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
7.3.4 USB3.2 Dual Channel Operation (MODE = “F”)
TheTUSB1002A in dual-channel operation waits for far-end terminations on both channels 1 and 2 before
transitioning to fully active state (U0 mode). This mode of operation, defined as MODE pin = ‘F’, is the most
common configuration for USB3.2 Source (DFP) and Sink (UFP) applications.
In a USB3.2 x2 application, two TUSB1002A redrivers are used: One on the config lane and the other on the
non-config lane. The TUSB1002A on the non-config lane must be placed in basic redriver mode (MODE pin =
"0"). The TUSB1002A on the config lane should be placed in USB3.2 dual channel operation (MODE pin = "F").
The expectation is the USB power delivery (PD) controller will hold both TUSB1002A in shutdown mode until a
connection can be established. Upon establishing a connection, the USB PD controller will place each
TUSB1002A into the appropriate mode.
7.3.5 USB3.2 Single Channel Operation (MODE = “1”)
In some applications, like Type-C USB3.2 active cables, only one of the two channels may be active. For this
application, setting MODE pin = ‘1’, enables single-channel operation. In this mode of operation, the TUSB1002A
attempts far-end termination on both channels 1 and 2. The channel which has a far-end termination detected is
enabled while the remaining channel is disabled. If far-end termination is detected on both channels, then
TUSB1002A behaves in dual channel operation (both channels enabled).
7.3.6 PCIe/SATA/SATA Express Redriver Operation (MODE = “R”; CFG1 = "0"; CFG2 = "0" )
The TUSB1002A can be used as a PCI Express (PCIe) Gen3, SATA Gen3, or SATA Express redriver. When
TUSB1002A's MODE pin = “R”, CFG1 pin = "0", and CFG2 pin = "0", the TUSB1002A enables both channels
(upstream and downstream) receiver and transmitter paths upon detecting far-end termination on both TX1 and
TX2. Both upstream and downstream paths remain enabled until EN pin is de-asserted low. All USB3.2 power
management functionality is disabled in this mode. In this mode, the TUSB1002A is transparent to PCIe link
power management (L0s, L1) and SATA interface power states. Once far-end termination is detected on both
TX1 and TX2, the TUSB1002A power is at P(U0_SSP_1200mV) regardless of the PCIe or SATA power state. To save
power during system S3/S4/S5 states it is suggested to de-assert the EN pin to conserve power.
注
In this mode the linearity range will be fixed at 1200mVpp and DC gain to 0dB.
7.3.7 Basic Redriver Operation (MODE = “0”)
The TUSB1002A can be used as a basic redriver for non-USB3.2 x1 applications. When the TUSB1002A MODE
pin = “0”, the TUSB1002A enables both channels receiver and transmitter paths. The channel receiver and
transmitter termination are both enabled. All USB3.2 power management functionality is disabled.
版权 © 2018, Texas Instruments Incorporated
17
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
7.4 Device Functional Modes
7.4.1 Shutdown Mode
The Shutdown mode is entered when EN pin is low and VCC is active and stable. This mode is the lowest power
state of the TUSB1002A. While in this mode, the TUSB1002A receiver terminations is disabled.
7.4.2 Disconnect Mode
Next to Shutdown Mode, the Disconnect mode is the lowest power state of the TUSB1002A. The TUSB1002A
enters this mode when exiting Shutdown mode. In this state, the TUSB1002A periodically checks for far-end
receiver termination on both SSTX1 and SSTX2. Upon detection of the far-end receiver’s termination on both
ports, the TUSB1002A transitions to a fully active mode called U0 mode.
7.5 U0 Mode
The U0 mode is the highest power state of the TUSB1002A. Anytime high-speed traffic (SuperSpeed or
SuperSpeedPlus) is being received, the TUSB1002A remains in this mode. The TUSB1002A only exits this
mode if electrical idle is detected on both SSRX1 and SSRX2. While in this mode, the TUSB1002A hs speed
receivers and transmitters are powered and active.
7.6 U1 Mode
The U1 mode is the intermediate mode between U0 mode and U2/U3 mode. In U1 mode, the TUSB1002A
receiver termination remains enabled and the TXP/N DC common mode is maintained.
7.7 U2/U3 Mode
Next to the disconnect mode, the U2/U3 mode is next lowest power state. While in this mode, the TUSB1002A
periodically performs far-end receiver detection. Anytime the far-end receiver termination is not detected on
either CH1 or CH2, the TUSB1002A leaves the U2/U3 mode and transition to the Disconnect mode. It also
monitors the SSRX1 and SSRX2 for a valid LFPS. Upon detection of a valid LFPS, the TUSB1002A immediately
transitions to the U0 mode.
18
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
8 Application and Implementation
注
Information in the following applications sections is not part of the TI component
specification, and TI does not warrant its accuracy or completeness. TI’s customers are
responsible for determining suitability of components for their purposes. Customers should
validate and test their design implementation to confirm system functionality.
8.1 Application Information
The TUSB1002A is a linear redriver designed specifically to compensation for ISI jitter caused by attenuation
through a passive medium like traces and cables. Because the TUSB1002A has two independent channels, it
can be optimized to correct ISI in both the upstream and downstream direction through 16 different equalization
choices. Placing the TUSB1002A between a USB3.2 Host/device controller and a USB3.2 receptacle can correct
signal integrity issues resulting in a more robust system.
8.2 Typical USB3.2 Application
Downstream
B
A
C
D
FR4 Trace
of Length Y
FR4 Trace
of Length X
C
C
C
C
RXP1
TXP1
TXN1
+
-
+
-
+
RXN1
-
TUSB1002A
+
USB 3.1
Host
C
C
C
C
TXP2
TXN2
RXP2
RXN2
+
-
+
-
-
Upstream
图 17. TUSB1002A in USB3.2 x1 Host Application
8.2.1 Design Requirements
For this design example, use the parameters shown in 表 4.
表 4. Design Parameters
PARAMETER
VALUE
VCC supply (3 V to 3.6 V)
3.3 V
Mode of Operation (Dual or Half Channel)
TX1, TX2, RX1 A/C coupling Capacitor (75 nF to 265 nF)
Optional RX2 A/C coupling Capacitor (297 nF to 363 nF)
MODE = F (Floating) for USB3.2 Dual Channel
100 nF
330 nF ±10%
Optional RX2 pull-down resistors on USB receptacle side of AC
capacitor (200K to 242K ohms)
220 kΩ
A to B FR4 Length (inches)
A to B FR4 Trace Width (mils)
C to D FR4 length (inches)
8
4
2
C to D FR4 Trace Width (mils)
DC Gain (-2, -1, 0, +1, +2)
4
0 dB (CFG[2:1] pins floating)
1200 mV (CFG[2:1] pins floating)
Linear Range (900 mV, 1000 mV, or 1200 mV)
版权 © 2018, Texas Instruments Incorporated
19
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
8.2.2 Detailed Design Procedure
The TUSB1002A differential receivers and transmitters have internal BIAS and termination. For this reason, the
TUSB1002A must be connected to the USB3.2 host and receptacle through external A/C coupling capacitors. In
this example, as depicted in 表 4, 100 nF capacitors are placed on TX2P and TX2N, RX1P and RX1N, and TX1P
and TX1N. 330 nF A/C coupling capacitors along with 220 kΩ resistors are placed on the RX2P and RX2N.
Inclusion of the 330 nF capacitors and 220k resistors is optional. The ordered list below details the three
implementation options for the RX2p/n path.
Three implementation options for USB connector to TUSB1002A's RX pins:
1. DC couple TUSB1002A's RX pins to USB connector. No 330 nF capacitors and no 220 kΩ pull-down
resistors.
2. 330 nF capacitors with 220 kΩ resistors as depicted in 图 18. The purpose of 220 kΩ resistors is to
discharge the capacitor within 250ms after a USB device is removed from the USB connector.
3. The stub from the 220 kΩ resistor pad may create impedance discontinuities causing negative impact to
performance. Assuming leakage current from external components is enough to discharge capacitor, 330 nF
capacitor without the 220 kΩ resistor is a valid option.
CH2_EQ2
CH2_EQ1
USB_VBUS
CFG2
J1
Optional
VCC_3P3V
1
VBUS
2
DM
HOST_DM
HOST_DP
3
U1
DP
GND
4
5
C12
C13
TX2P
RX2P
C1
C2
19
20
21
12
11
SSRXN
HOST_RXP
HOST_RXN
330nF
330nF
100nF
100nF
CONNECT TO
USB3.1 HOST
RX2N
GND
6
7
8
9
TX2N
GND
SSRXP
GND
10
9
C3
C5
C4
C6
TUSB1002A
24-PIN RGE
HOST_TXP
HOST_TXN
SSTXN
SSTXP
22
23
TX1P
TX1N
RX1P
RX1N
100nF
100nF
100nF
100nF
8
10
11
SHIELD0
SHIELD1
24
25
MODE
7
RSVD1
GND
R16
220k
R15
220k
VCC_3P3V
VCC_3P3V
1
2
3
4
5
6
USB3_TYPEA_CONNECTER
R2
DNI
C7
100nF
VCC_3P3V
C8
0.001uF
R1
1M
Optional
C10
C11
C9
10uF
100nF
100nF
CFG1
CH1_EQ2
CH1_EQ1
Copyright © 2018, Texas Instruments Incorporated
图 18. Host Implementation Schematic
The USB3.2 Dual channel operation is used in this example. Mode pin should be left floating (unconnected)
when using this mode.
The TUSB1002A compensates for channel loss in both the upstream (D to C) and downstream direction (A to B).
This is done by configuring the CH1_EQ[2:1] and CH2_EQ[2:1] pins to the equalization setting that matches as
close possible to the channel insertion loss. In this particular example, CH1_EQ[2:1] is for path A to B which is
the channel between USB3.2 host and the TUSB1002A, and CH2_EQ[2:1] is for path C to D which is the
channel between TUSB1002A and the USB3.2 receptacle.
The TUSB1002A supports 5 levels of DC gain that are selected by the CFG[2:1] pins. Typically, the DC gain
should be set to 0 dB but may need to be adjusted to correct any one of the following conditions:
1. Input VID too high resulting in VOD being greater than USB 3.2 defined swing. For this case, a negative DC
gain should be used.
2. Input VID too low resulting in VOD being less than USB 3.2 defined swing. For this case, a positive DC gain
should be used.
3. Low frequency discontinuities in the channel resulting in DC component of the signal clipping the vertical eye
mask. For this case, a positive DC gain should be used.
20
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
It is assumed in this example the incoming VID is at the nominal defined USB3.2 range and the channel is linear
across frequency. The CFG1 and CFG2 pins can both be left floating if these assumptions are true.
In this particular example, the channel A-B has a trace length of 8 inches with a 4 mil trace width. This particular
channel has about 0.83 dB per inch of insertion loss at 5 GHz. This equates to approximately 6.7 dB of loss for
the entire 8 inches of trace. An additional 1.5 dB of loss is added due to package of the USB3.2 Host,
TUSB1002A, and the A/C coupling capacitor. This brings the entire channel loss at 5 GHz to 6.7 dB + 1.5 dB =
8.2 dB. A typical USB 3.1 host/device will have around 3 dB of transmitter de-emphasis. Transmitter de-
emphasis pre-compensates for the loss of the output channel. With 3 dB of de-emphasis, the total equalization
required by the TUSB1002A is in the 5.2 dB (8.2 dB - 3 dB) range. The channel A-B for this example is
connected to TUSB1002A's RX1P/N input and therefore CH1_EQ[2:1] pins are used for adjusting TUSB1002A
RX1P/N equalization settings. The CH1_EQ[2:1] pins should be set such that TUSB1002A equalization is
between 5dB and 8dB.
The channel C-D has a trace length of 2 inches with a 4mil trace width. Assuming 0.83 dB per inch of insertion
loss, the 2 inch trace will equate to about 1.66 dB of loss at 5 GHz. An additional 2dB of loss needs to be added
due to package, A/C coupling capacitor, and the USB 3.1 receptacle. The total loss is around 3.66 dB. Because
channel C-D includes a USB 3.1 receptacle, the actual total loss could be much greater than 3.66dB due to the
fact that devices plugged into the receptacle will also have loss. The device plugged into receptacle will have
either a short or long channel. USB3.2 standard defines total loss limit of 23dB that is distributed as 8.5 dB for
Host, 8.5dB for device, and 6.0dB for cable. With variable channel of devices plugged into the USB3.2
receptacle, configuring TUSB1002A's RX2P/N equalization settings is not as straight forward as Channel A-B.
Engineer can not set TUSB1002A CH2_EQ[2:1] pins to the largest equalization setting to accommodate the
largest allowed USB3.2 device/cable loss of 14.5 dB. Doing so will result in TUSB1002A operating outside its
linear range when a device with short channel is plugged into the receptacle. For this reason, it is recommended
to configure TUSB1002A CH2_EQ[2:1] pins to equalize a shorter device channel. This will result in requiring
USB3.2 host to compensate for remaining channel loss for the worse case USB3.2 channel of 14.5 dB. The
definition of a short device channel is not specified in USB 3.2 specification. Therefore, an engineer must make
their own loss estimate of what constitutes a short device channel. For particular example, we will assume the
short channel is around 2 to 3 dB. The device's channel loss will need to be added to estimated Channel C-D
loss minus the typical 3db of de-emphasis. This means CH2_EQ[2:1] pins should be configured to handle a loss
of 3 to 5 db.
8.2.3 Application Curves
Freq = 5 GHz
dB(SDD21) = –6.666
图 19. Insertion Loss for 8inch 4 mil FR4 Trace
版权 © 2018, Texas Instruments Incorporated
21
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
8.3 Typical SATA, PCIe and SATA Express Application
Downstream
A
B
C
D
FR4 trace
FR4 trace
of length X
of length Y
RXP2
TXP2
+
-
+
-
+
-
+
-
TXN2
RXN2
SATA/PCIe/
SATA Express
Host
SATA/PCIe/
SATA Express
Device
TUSB1002A
RXP1
RXN1
TXP1
TXN1
+
-
+
-
+
-
+
-
Upstream
图 20. SATA/PCIe/SATA Express Typical Application
8.3.1 Design Requirements
表 5. Design Parameters
PARAMETER
VALUE
3.3 V
Yes
VCC supply (3 V to 3.6 V)
PCIe Support Required (Yes/No)
SATA Express Support Required (Yes/No)
Yes
Yes, then ferrite beads (FB1 and FB2) and 49.9-ohm required.
No, then ferrite bead (FB1 and FB2) and 49.9-ohm not required.
SATA Support Required (Yes/No)
TX1, TX2, RX2 A/C coupling Capacitor (176 nF to 265 nF)
RX1 A/C coupling Capacitor (297 nF to 363 nF)
A to B FR4 Length (inches)
220 nF ±10%
Optional. But if implemented suggest 330 nF ±10%
8
4
2
4
A to B FR4 Trace Width (mils)
C to D FR4 length (inches)
C to D FR4 Trace Width (mils)
Not configurable when MODE = "R", CFG1 = "0", and CFG2 = "0".
Will always default to 0 dB
DC Gain (-2, -1, 0, +1, +2)
Not configurable when MODE = "R", CFG1 = "0", and CFG2 = "0".
Will always default to 1200mV
Linear Range (900 mV, 1000 mV, or 1200 mV)
8.3.2 Detailed Design Procedure
The MODE pin = "R", CFG1 = "0", and CFG2 = "0" will place the TUSB1002A into PCIe mode. In this mode, the
TUSB1002A will have its DC gain fixed at 0dB and its linearity range fixed at 1200mV. The TUSB1002A will
perform far-end receiver termination detection and enable both upstream and downstream paths when far-end
termination is detected on both TX1 and TX2.
The AC coupling capacitor range defined for a SATA device is a lot smaller than the AC-coupling capacitor range
defined for SATA Express and PCI Express (PCIe) as indicated by 图 21. The AC-coupling capacitor range
defined for SATA Express and PCI Express is within the same range as the AC-coupling capacitor range defined
by USB 3.1. The TUSB1002A will be able to detect PCIe and SATA Express device's receiver termination. But
the SATA 12nF (max) AC-coupling capacitor prevents TUSB1002A from detecting the SATA device receiver
termination. To correct this problem, a ferrite bead along with 49.9 ohm resistor must be placed between CTX2
and miniCard/mSATA socket. These components can be isolated from the high-speed channel when PCIe or
SATA Express is active by using an NFET as shown in 图 22. The NFET should be enabled whenever a SATA
22
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
device is present. The ferrite bead chosen must present at least 600 ohms impedance at 100MHz so as to not
impact high-speed signalling. It is recommended to use Murata BLM03AG601SN1 or BLM03HD601SN1D or a
ferrite bead with similar characteristics from a different vendor. For applications which only require support for
PCIe and SATA Express and do not need to support SATA, the ferrite beads and 49.9 ohm resistors are not
needed.
12nF (max)
176nF t 265nF
+
-
+
-
+
-
SATA
Express
Device
SATA
Device
PCIe
Device
+
-
+
-
+
-
75nF t 265nF
图 21. AC-Coupling capacitor Implementation for SATA, SATA Express, and PCIe Devices
The TUSB1002A power is at P(U0_SSP_1200mV) when both its upstream and downstream paths are enabled. In
order to save system power in system S3/S4/S5 states, it is suggested to control the TUSB1002A EN pin.
Anytime the system enters a low power state (S3, S4, or S5), it is suggested to de-assert the EN pin. While EN
pin is de-asserted, the TUSB1002A will consume P(SHUTDOWN). Assertion of this pin is necessary anytime the
system exits a lower power state.
The TUSB1002A compensates for channel loss in both the upstream (C to D) and downstream direction (A to B).
This is done by configuring the CH1_EQ[2:1] and CH2_EQ[2:1] pins to the equalization setting that matches as
close possible to the channel insertion loss. In this particular example, CH2_EQ[2:1] is for path A to B which is
the channel between PCIe/SATA/SATA Express host and the TUSB1002A, and CH1_EQ[2:1] is for path C to D
which is the channel between TUSB1002A and the miniCard/mSATA socket.
In this particular example, the channel A-B has a trace length of 8 inches with a 4 mil trace width. This particular
channel has about 0.83 dB per inch of insertion loss at 5 GHz. This equates to approximately 6.7 dB of loss for
the entire 8 inches of trace as depicted in 图 19. An additional 1.5 dB of loss is added due to package of the
PCIe/SATA/SATA Express Host, TUSB1002A, and the A/C coupling capacitor. This brings the entire channel
loss at 5 GHz to 6.7 dB + 1.5 dB = 8.2 dB. The channel A-B for this example is connected to TUSB1002A
RX2P/N input and therefore CH2_EQ[2:1] pins are used for adjusting TUSB1002A RX2P/N equalization settings.
The CH2_EQ[2:1] pins should be set such that TUSB1002A equalization is between 5dB and 8dB. A value closer
to 5 dB maybe best if Host has transmitter de-emphasis.
A similar method should be used for the upstream path (C to D). In this particular example, C to D has a trace
length of 2 inches with a 4-mil trace width. This equates to approximately 1.5 dB at 5 GHz. The SATA/SATA
Express/PCIe device will have its own channel loss. This loss can be added to the C to D channel loss. For this
example, we will assume a value of 5dB is acceptable to compensate for C to D channel loss as well as loss
associated with the SATA/SATA Express/PCIe device. The CH1_EQ[2:1] pins should be set such that
TUSB1002A equalization is 5dB.
版权 © 2018, Texas Instruments Incorporated
23
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
VCC (3.3V)
VCC (3.3V)
REQ2A
100nF
10 µF
100nF
REQ2B
VCC (3.3V)
REQ2C
SATA_EN
REQ2D
10YQ
49.9Q
49.9Q
FB2
FB1
CRX2
CTX2
TX2P
TX2N
GND
RX1P
RX1N
MODE
RX2P
RX2N
GND
TX1P
TX1N
RSVD1
+
-
SATA/PCIe/
SATA Express
TUSB1002A
Host
+
-
CRX1
CTX1
20YQ
VCC (3.3V)
0-Q
GPIO (S3/S3/S5 indicator)
REQ1A
REQ1B
VCC (3.3V)
REQ1C
REQ1D
图 22. Example SATA/PCIe/SATA Express Schematic
24
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
8.3.3 Application Curves
图 23. PCIe Gen1 TX Eye Diagram
图 24. PCIe Gen 3 TX Eye Diagram
9 Power Supply Recommendations
The TUSB1002A has two VCC supply pins. It is recommended to place a 100 nF de-coupling capacitor near each
of the VCC pins. It is also recommended to have at least one bulk capacitor of at least 10 µF on the VCC plane
near the TUSB1002A.
10 Layout
10.1 Layout Guidelines
•
•
•
RXP/N and TXP/N pairs should be routed with controlled 90-Ω differential impedance (±15%).
Keep away from other high speed signals.
In USB3 applications maintaining polarity thru the TUSB1002A is not necessary. Therefore it is recommended
to connect polarity in such a way that produces the best routing.
•
•
•
•
•
Intra-pair routing should be kept to within 2 mils.
Intra-pair length matching should be near the location of mismatch.
Inter-pair length matching is not necessary.
Each pair should be separated at least by 3 times the signal trace width.
The use of bends in differential traces should be kept to a minimum. When bends are used, the number of left
and right bends should be as equal as possible and the angle of the bend should be ≥ 135 degrees. This
minimizes any length mismatch causes by the bends; ad therefore, minimize the impact bends have on EMI.
•
•
•
•
•
Route all differential pairs on the same of layer.
The number of VIAS should be kept to a minimum. It is recommended to keep the VIAS count to 2 or less.
Keep traces on layers adjacent to ground plane.
Do NOT route differential pairs over any plane split.
When using thru-hole USB connectors, it is recommend to route differential pairs on bottom layer in order to
minimize the stub created by the thru-hole connector.
•
Adding Test points causes impedance discontinuity; and therefore, negatively impact signal performance. If
test points are used, they should be placed in series and symmetrically. They must not be placed in a manner
that causes a stub on the differential pair.
版权 © 2018, Texas Instruments Incorporated
25
TUSB1002A
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
www.ti.com.cn
10.2 Layout Example
Example 4 layer PCB Stackup
Top Layer 1 (Signal)
Inner Layer 2 (GND)
Inner Layer 3 (VCC)
Bottom Layer 4 (Signal)
Place near TUSB1002A
Via to layer 2 (GND)
Via to layer 3 (VCC)
Place near TUSB1002A
or USB 3.1 receptacle
18
13
19
12
24
7
Place near TUSB1002A
or USB 3.1 receptacle
1
6
Place near TUSB1002A.
图 25. Example Layout
26
版权 © 2018, Texas Instruments Incorporated
TUSB1002A
www.ti.com.cn
ZHCSHW9A –MARCH 2018–REVISED NOVEMBER 2018
11 器件和文档支持
11.1 接收文档更新通知
要接收文档更新通知,请导航至 TI.com.cn 上的器件产品文件夹。单击右上角的通知我 进行注册,即可每周接收产
品信息更改摘要。有关更改的详细信息,请查看任何已修订文档中包含的修订历史记录。
11.2 社区资源
下列链接提供到 TI 社区资源的连接。链接的内容由各个分销商“按照原样”提供。这些内容并不构成 TI 技术规范,
并且不一定反映 TI 的观点;请参阅 TI 的 《使用条款》。
TI E2E™ 在线社区 TI 的工程师对工程师 (E2E) 社区。此社区的创建目的在于促进工程师之间的协作。在
e2e.ti.com 中,您可以咨询问题、分享知识、拓展思路并与同行工程师一道帮助解决问题。
设计支持
TI 参考设计支持 可帮助您快速查找有帮助的 E2E 论坛、设计支持工具以及技术支持的联系信息。
11.3 商标
E2E is a trademark of Texas Instruments.
All other trademarks are the property of their respective owners.
11.4 静电放电警告
ESD 可能会损坏该集成电路。德州仪器 (TI) 建议通过适当的预防措施处理所有集成电路。如果不遵守正确的处理措施和安装程序 , 可
能会损坏集成电路。
ESD 的损坏小至导致微小的性能降级 , 大至整个器件故障。 精密的集成电路可能更容易受到损坏 , 这是因为非常细微的参数更改都可
能会导致器件与其发布的规格不相符。
11.5 术语表
SLYZ022 — TI 术语表。
这份术语表列出并解释术语、缩写和定义。
12 机械、封装和可订购信息
以下页面包含机械、封装和可订购信息。这些信息是指定器件的最新可用数据。数据如有变更,恕不另行通知,且
不会对此文档进行修订。如需获取此产品说明书的浏览器版本,请查阅左侧的导航栏。
版权 © 2018, Texas Instruments Incorporated
27
PACKAGE OPTION ADDENDUM
www.ti.com
28-Sep-2021
PACKAGING INFORMATION
Orderable Device
Status Package Type Package Pins Package
Eco Plan
Lead finish/
Ball material
MSL Peak Temp
Op Temp (°C)
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
(6)
TUSB1002AIRGER
TUSB1002AIRGET
TUSB1002ARGER
TUSB1002ARGET
ACTIVE
VQFN
VQFN
VQFN
VQFN
RGE
24
24
24
24
3000 RoHS & Green
250 RoHS & Green
3000 RoHS & Green
250 RoHS & Green
NIPDAU
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
Level-1-260C-UNLIM
-40 to 85
-40 to 85
0 to 70
TUSB
1002A
ACTIVE
ACTIVE
ACTIVE
RGE
NIPDAU
NIPDAU
NIPDAU
TUSB
1002A
RGE
TUSB
1002A
RGE
0 to 70
TUSB
1002A
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) RoHS: TI defines "RoHS" to mean semiconductor products that are compliant with the current EU RoHS requirements for all 10 RoHS substances, including the requirement that RoHS substance
do not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, "RoHS" products are suitable for use in specified lead-free processes. TI may
reference these types of products as "Pb-Free".
RoHS Exempt: TI defines "RoHS Exempt" to mean products that contain lead but are compliant with EU RoHS pursuant to a specific EU RoHS exemption.
Green: TI defines "Green" to mean the content of Chlorine (Cl) and Bromine (Br) based flame retardants meet JS709B low halogen requirements of <=1000ppm threshold. Antimony trioxide based
flame retardants must also meet the <=1000ppm threshold requirement.
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
(6)
Lead finish/Ball material - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead finish/Ball material values may wrap to two
lines if the finish value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
28-Sep-2021
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Nov-2018
TAPE AND REEL INFORMATION
*All dimensions are nominal
Device
Package Package Pins
Type Drawing
SPQ
Reel
Reel
A0
B0
K0
P1
W
Pin1
Diameter Width (mm) (mm) (mm) (mm) (mm) Quadrant
(mm) W1 (mm)
TUSB1002AIRGER
TUSB1002AIRGET
TUSB1002ARGER
TUSB1002ARGET
VQFN
VQFN
VQFN
VQFN
RGE
RGE
RGE
RGE
24
24
24
24
3000
250
330.0
180.0
330.0
180.0
12.4
12.4
12.4
12.4
4.25
4.25
4.25
4.25
4.25
4.25
4.25
4.25
1.15
1.15
1.15
1.15
8.0
8.0
8.0
8.0
12.0
12.0
12.0
12.0
Q2
Q2
Q2
Q2
3000
250
Pack Materials-Page 1
PACKAGE MATERIALS INFORMATION
www.ti.com
2-Nov-2018
*All dimensions are nominal
Device
Package Type Package Drawing Pins
SPQ
Length (mm) Width (mm) Height (mm)
TUSB1002AIRGER
TUSB1002AIRGET
TUSB1002ARGER
TUSB1002ARGET
VQFN
VQFN
VQFN
VQFN
RGE
RGE
RGE
RGE
24
24
24
24
3000
250
367.0
210.0
367.0
210.0
367.0
185.0
367.0
185.0
35.0
35.0
35.0
35.0
3000
250
Pack Materials-Page 2
GENERIC PACKAGE VIEW
RGE 24
VQFN - 1 mm max height
PLASTIC QUAD FLATPACK - NO LEAD
Images above are just a representation of the package family, actual package may vary.
Refer to the product data sheet for package details.
4204104/H
PACKAGE OUTLINE
VQFN - 1 mm max height
RGE0024H
PLASTIC QUAD FLATPACK- NO LEAD
A
4.1
3.9
B
4.1
3.9
PIN 1 INDEX AREA
1 MAX
C
SEATING PLANE
0.08 C
0.05
0.00
ꢀꢀꢀꢀꢁꢂꢃꢄꢂꢅ
(0.2) TYP
2X 2.5
12
7
20X 0.5
6
13
25
2X
SYMM
2.5
1
18
0.30
PIN 1 ID
(OPTIONAL)
24X
0.18
24
19
0.1
0.05
C A B
C
SYMM
0.48
0.28
24X
4219016 / A 08/2017
NOTES:
1. All linear dimensions are in millimeters. Any dimensions in parenthesis are for reference only. Dimensioning and tolerancing
per ASME Y14.5M.
2. This drawing is subject to change without notice.
3. The package thermal pad must be soldered to the printed circuit board for thermal and mechanical performance.
www.ti.com
EXAMPLE BOARD LAYOUT
VQFN - 1 mm max height
RGE0024H
PLASTIC QUAD FLATPACK- NO LEAD
(3.825)
2.7)
(
24
19
24X (0.58)
24X (0.24)
1
18
20X (0.5)
25
SYMM
(3.825)
2X
(1.1)
ꢆꢄꢂꢁꢇꢀ9,$
TYP
6
13
(R0.05)
7
12
2X(1.1)
SYMM
LAND PATTERN EXAMPLE
SCALE: 20X
0.07 MIN
ALL AROUND
0.07 MAX
ALL AROUND
METAL
SOLDER MASK
OPENING
SOLDER MASK
OPENING
METAL UNDER
SOLDER MASK
NON SOLDER MASK
DEFINED
SOLDER MASK
DEFINED
(PREFERRED)
SOLDER MASK DETAILS
4219016 / A 08/2017
NOTES: (continued)
4. This package is designed to be soldered to a thermal pad on the board. For more information, see Texas Instruments
literature number SLUA271 (www.ti.com/lit/slua271).
5. Solder mask tolerances between and around signal pads can vary based on board fabrication site.
www.ti.com
EXAMPLE STENCIL DESIGN
VQFN - 1 mm max height
RGE0024H
PLASTIC QUAD FLATPACK- NO LEAD
(3.825)
4X ( 1.188)
24
19
24X (0.58)
24X (0.24)
1
18
20X (0.5)
SYMM
(3.825)
(0.694)
TYP
6
13
25
(R0.05) TYP
METAL
TYP
7
12
(0.694)
TYP
SYMM
SOLDER PASTE EXAMPLE
BASED ON 0.125 mm THICK STENCIL
EXPOSED PAD
78% PRINTED COVERAGE BY AREA
SCALE: 20X
4219016 / A 08/2017
NOTES: (continued)
6. Laser cutting apertures with trapezoidal walls and rounded corners may offer better paste release. IPC-7525 may have alternate
design recommendations..
www.ti.com
重要声明和免责声明
TI 提供技术和可靠性数据(包括数据表)、设计资源(包括参考设计)、应用或其他设计建议、网络工具、安全信息和其他资源,不保证没
有瑕疵且不做出任何明示或暗示的担保,包括但不限于对适销性、某特定用途方面的适用性或不侵犯任何第三方知识产权的暗示担保。
这些资源可供使用 TI 产品进行设计的熟练开发人员使用。您将自行承担以下全部责任:(1) 针对您的应用选择合适的 TI 产品,(2) 设计、验
证并测试您的应用,(3) 确保您的应用满足相应标准以及任何其他安全、安保或其他要求。这些资源如有变更,恕不另行通知。TI 授权您仅可
将这些资源用于研发本资源所述的 TI 产品的应用。严禁对这些资源进行其他复制或展示。您无权使用任何其他 TI 知识产权或任何第三方知
识产权。您应全额赔偿因在这些资源的使用中对 TI 及其代表造成的任何索赔、损害、成本、损失和债务,TI 对此概不负责。
TI 提供的产品受 TI 的销售条款 (https:www.ti.com.cn/zh-cn/legal/termsofsale.html) 或 ti.com.cn 上其他适用条款/TI 产品随附的其他适用条款
的约束。TI 提供这些资源并不会扩展或以其他方式更改 TI 针对 TI 产品发布的适用的担保或担保免责声明。IMPORTANT NOTICE
邮寄地址:上海市浦东新区世纪大道 1568 号中建大厦 32 楼,邮政编码:200122
Copyright © 2021 德州仪器半导体技术(上海)有限公司
相关型号:
©2020 ICPDF网 联系我们和版权申明