UC3710DWTR [TI]
BUF OR INV BASED MOSFET DRIVER, PDSO16;
| 型号： | UC3710DWTR |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | BUF OR INV BASED MOSFET DRIVER, PDSO16 驱动 光电二极管 接口集成电路 驱动器 |
| 文件： | 总7页 (文件大小：94K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
UC1710
UC2710
UC3710
High Current FET Driver
FEATURES
DESCRIPTION
• Totem Pole Output with 6A
Source/Sink Drive
The UC1710 family of FET drivers is made with a high-speed Schottky pro-
cess to interface between low-level control functions and very high-power
switching devices-particularly power MOSFET’s. These devices accept
low-current digital inputs to activate a high-current, totem pole output which
can source or sink a minimum of 6A.
• 3ns Delay
• 20ns Rise and Fall Time into 2.2nF
• 8ns Rise and Fall Time into 30nF
• 4.7V to 18V Operation
Supply voltages for both V and V can independently range from 4.7V to
IN
C
18V. These devices also feature under-voltage lockout with hysteresis.
The UC1710 is packaged in an 8-pin hermetically sealed dual in-line pack-
age for –55°C to +125°C operation. The UC2710 and UC3710 are speci-
fied for a temperature range of –40°C to +85°C and 0°C to +70°C
respectively and are available in either an 8-pin plastic dual in-line or a
5-pin, TO-220 package. Surface mount devices are also available.
• Inverting and Non-Inverting Outputs
• Under-Voltage Lockout with
Hysteresis
• Thermal Shutdown Protection
• MINIDIP and Power Packages
ORDERING INFORMATION
TEMPERATURE
RANGE
PACKAGE
TRUTH TABLE
UC1710J
UC2710DW
UC2710J
UC2710N
UC2710T
UC3710DW
UC3710N
UC3710T
–55°C to +125°C
–40°C to +85°C
8 pin CDIP
INV
H
N.I.
H
Out
L
16 pin SOIC-wide
8 pin CDIP
OUT= INV and N.I.
OUT= INV or N.I.
8 pin PDIP
L
H
H
5 pin TO220
16 pin SOIC-wide
8 pin PDIP
H
L
L
0°C to +70°C
L
L
L
5 pin TO220
BLOCK DIAGRAM
INTERNALLY CONNECTED IN T PACKAGE
OUTPUT BIAS
5
VIN
4
VC
LOGIC BIAS
3
2
Out
N.I. IN
8
TSD
Pwr Gnd
INV IN
1
7
UVLO
Logic Gnd
INTERNALLY CONNECTED IN T PACKAGE
UDG-99079
05/99
UC1710
UC2710
UC3710
ABSOLUTE MAXIMUM RATINGS
N-Package
J-Package
T-Package
Supply Voltage, Vin . . . . . . . . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Collector Supply Voltage, VC . . . . . . . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V . . . . . . . . . . . . . . 20V
Operating Voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V . . . . . . . . . . . . . . 18V
Output Current (Source or Sink)
±
Steady-State. . . . . . . . . . . . . . . . . . . . . . . . . . . . . ± 500mA. . . . . . . . . . . . 500mA . . . . . . . . . . . . . ± 1A
Digital Inputs . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3V-VIN . . . . . . . . –0.3V – VIN . . . . . . . . –0.3V – VIN
Power Dissipation at Ta=25°C . . . . . . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 1W. . . . . . . . . . . . . . . 3W
Power Dissipation at T (Case) = 25°C. . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . . 2W. . . . . . . . . . . . . . 25W
Operating Junction Temperature. . . . . . . –55°C to +150°C . . . . –55°C to +150°C . . . . –55°C to +150°C
Storage Temperature . . . . . . . . . . . . . . . –65°C to +150°C . . . . –65°C to +150°C . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 seconds) . . . . . . . 300°C . . . . . . . . . . . . 300°C . . . . . . . . . . . . 300°C
Note 1: All currents are positive into, negative out of the specified terminal.
Note 2: Consult Unitrode Integrated Circuits databook for information regarding thermal specifications
and limitations of packages.
CONNECTION DIAGRAMS
DIL-8 MINIDIP (Top View)
J or N Package
SOIC-16 (Top View)
DW Package
5-Pin TO-220 (Top View)
T Package
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
VIN Supply Current
TEST CONDITIONS
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V, Output High
VIN =18V, VC =18V, Output Low
VIN =18V, VC =18V,Output High
VIN High to Low
MIN
TYP
26
MAX UNITS
35
30
5.0
8
mA
mA
mA
mA
V
21
VC Supply Current
UVLO Threshold
1.5
5.0
4.1
4.4
3.8
4.1
4.4
4.8
VIN Low to High
V
2
UC1710
UC2710
UC3710
ELECTRICAL CHARACTERISTICS: Unless otherwise stated, these specifications apply for VIN = VC = 15V, No load,
TA = TJ.
PARAMETERS
TEST CONDITIONS
MIN
TYP
MAX UNITS
UVLO Threshold Hysteresis
Digital Input Low Level
Digital Input High Level
Digital Input Current
0.1
0.3
0.5
0.8
V
V
2.0
V
Digital Input = 0.0V
–70
–4.0
1.35
3.2
µA
V
Output High Sat., VC – VO
IO= –100mA
IO= –6A
2.2
4.5
0.6
4.5
V
Output Low Sat., VO
IO= 100mA
IO= 6A
0.25
3.4
V
V
Thermal Shutdown
165
°C
From Inv., Input to Output (Note 3, 4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
70
70
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
CL = 2.2nF
CL = 30nF
CL = 0
70
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
40
CL = 2.2nF
CL = 30nF
CL = 0
40
150
70
CL = 2.2nF
CL = 30nF
CL = 0
70
80
40
CL = 2.2nF
CL = 30nF
40
150
From N.I. Input to Output (Note 3,4):
Rise Time Delay
CL = 0
35
35
35
20
25
85
35
35
35
15
20
85
30
70
70
70
40
40
150
70
70
80
40
50
150
40
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
mA
CL = 2.2nF
CL = 30nF
CL = 0
10% to 90% Rise
Fall Time Delay
90% to 10% Fall
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
CL = 0
CL = 2.2nF
CL = 30nF
TA = 25°C (Note 5) CL = 0
Total Supply Current at 200kHz Input
Switching Frequency
Note: 3. Delay measured from 50% input change to 10% output change.
Note: 4. Those parameters with CL = 30nF are not tested in production.
Note: 5. Inv. Input pulsed at 50% duty cycle with N.I. Input = 3V. or N.I. Input pulsed at 50% duty cycle with Inv. Input = 0V.
UNITRODE CORPORATION
7 CONTINENTAL BLVD. • MERRIMACK, NH 03054
TEL. (603) 424-2410 FAX (603) 424-3460
3
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
PACKAGING INFORMATION
Orderable Device
5962-0152001QPA
5962-0152001VPA
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-55 to 125
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
ACTIVE
CDIP
CDIP
JG
8
8
1
TBD
A42
A42
N / A for Pkg Type
0152001QPA
UC1710
ACTIVE
JG
1
TBD
N / A for Pkg Type
-55 to 125
0152001VPA
UC1710
5962-0152001VXA
UC1710J
ACTIVE
ACTIVE
ACTIVE
CDIP
CDIP
CDIP
JG
JG
JG
8
8
8
1
1
1
TBD
TBD
TBD
A42
A42
A42
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-55 to 125
-55 to 125
-55 to 125
0152001VXA
UC1710J
UC1710J883B
0152001QPA
UC1710
UC1710L883B
UC1710SP
UC2710N
OBSOLETE
OBSOLETE
ACTIVE
TO/SOT
CDIP
L
J
20
16
8
TBD
TBD
Call TI
Call TI
Call TI
Call TI
-55 to 125
-55 to 125
-40 to 85
PDIP
P
50
50
50
50
40
40
50
50
50
50
Green (RoHS
& no Sb/Br)
CU NIPDAU
N / A for Pkg Type
UC2710N
UC2710N
UC2710T
UC2710T
UC3710DW
UC3710DW
UC3710N
UC3710N
UC3710T
UC3710T
UC2710NG4
UC2710T
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
ACTIVE
PDIP
TO-220
TO-220
SOIC
P
KC
KC
DW
DW
P
8
5
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU SN
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
N / A for Pkg Type
-40 to 85
-40 to 85
-40 to 85
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
Green (RoHS
& no Sb/Br)
UC2710TG3
UC3710DW
UC3710DWG4
UC3710N
5
Green (RoHS
& no Sb/Br)
CU SN
16
16
8
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU SN
SOIC
Green (RoHS
& no Sb/Br)
PDIP
Green (RoHS
& no Sb/Br)
UC3710NG4
UC3710T
PDIP
P
8
Green (RoHS
& no Sb/Br)
TO-220
TO-220
KC
KC
5
Green (RoHS
& no Sb/Br)
UC3710TG3
5
Green (RoHS
& no Sb/Br)
CU SN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
OTHER QUALIFIED VERSIONS OF UC1710, UC1710-SP, UC3710 :
Catalog: UC3710, UC1710
•
Military: UC1710
•
Space: UC1710-SP
•
NOTE: Qualified Version Definitions:
Addendum-Page 2
PACKAGE OPTION ADDENDUM
www.ti.com
25-Sep-2013
Catalog - TI's standard catalog product
•
•
•
Military - QML certified for Military and Defense Applications
Space - Radiation tolerant, ceramic packaging and qualified for use in Space-based application
Addendum-Page 3
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明