UC5603DP [TI]
9-LINE SCSI ACTIVE TERMINATOR; 9线SCSI主动终结者型号: | UC5603DP |
厂家: | TEXAS INSTRUMENTS |
描述: | 9-LINE SCSI ACTIVE TERMINATOR |
文件: | 总11页 (文件大小:332K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
ꢀ ꢁꢂ ꢃꢄ ꢅ
ꢆ ꢇꢈ ꢉꢊꢋ ꢌꢁꢌ ꢉ ꢍꢁꢎ ꢉ ꢏꢋ ꢎ ꢋꢐ ꢑꢉ ꢊ ꢍꢎꢒ ꢐ
ꢓ
SLUS195B − MARCH 1997 − REVISED NOVEMBER 2003
D
D
D
D
D
D
Complies with SCSI, SCSI−2 and SPI−2
Standards
D
Logic Command Disconnects all
Termination Lines
6-pF Channel Capacitance during
Disconnect
D
D
D
D
Trimmed Termination Current to 3%
Trimmed Impedance to 3%
100-µA Supply Current in Disconnect Mode
Meets SCSI Hot Plugging
Negative Clamping on all Signal Lines
Current Limit and Thermal Shutdown
Protection
−400-mA Sourcing Current for Termination
+400-mA Sinking Current for Active
Negation Drivers
description
The UC5603 provides 9 lines of active termination for a SCSI (Small Computers Systems Interface) parallel bus.
The SCSI standard recommends active termination at both ends of the cable segment.
The UC5603 provides a disconnect feature which, when opened or driven high, will disconnect all terminating
resistors, and disables the regulator; greatly reducing standby power. The output channels remain high
impedance even without Termpwr applied. A low channel capacitance of 6 pF allows units at interim points of
the bus to have little to no effect on the signal integrity.
Functionally the UC5603 is similar to its predecessor, the UC5601 − 18 line Active Terminator. Several electrical
enhancements were incorporated in the UC5603, such as a sink/source regulator output stage to accommodate
all signal lines at 5 V, while the regulator remains at its nominal value, reduced channel capacitance to 6 pF
typical, and as with the UC5601, custom power packages are utilized to allow normal operation at full power
conditions (1.2 watts).
functional block diagram
UDG-94049
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
ꢔ
ꢔ
ꢐ
ꢒ
ꢥ
ꢕ
ꢠ
ꢀ
ꢁ
ꢞ
ꢎ
ꢟ
ꢉ
ꢙ
ꢒ
ꢗ
ꢊ
ꢘ
ꢕ
ꢍ
ꢎ
ꢍ
ꢖ
ꢗ
ꢡ
ꢘ
ꢙ
ꢟ
ꢚ
ꢛ
ꢜ
ꢜ
ꢝ
ꢝ
ꢖ
ꢖ
ꢙ
ꢙ
ꢗ
ꢗ
ꢖ
ꢞ
ꢞ
ꢢ
ꢟ
ꢠ
ꢚ
ꢚ
ꢡ
ꢡ
ꢗ
ꢝ
ꢜ
ꢛ
ꢞ
ꢞ
ꢙ
ꢘ
ꢢ
ꢎꢡ
ꢠ
ꢣ
ꢞ
ꢤ
ꢖ
ꢟ
ꢜ
ꢞ
ꢝ
ꢖ
ꢝ
ꢙ
ꢚ
ꢗ
ꢠ
ꢥ
ꢜ
ꢗ
ꢝ
ꢝ
ꢡ
ꢞ
ꢦ
Copyright 2003, Texas Instruments Incorporated
ꢚ
ꢙ
ꢟ
ꢝ
ꢙ
ꢚ
ꢛ
ꢝ
ꢙ
ꢞ
ꢢ
ꢖ
ꢘ
ꢖ
ꢟ
ꢡ
ꢚ
ꢝ
ꢧ
ꢝ
ꢡ
ꢚ
ꢙ
ꢘ
ꢨ
ꢜ
ꢉ
ꢗ
ꢛ
ꢡ
ꢞ
ꢝ
ꢜ
ꢗ
ꢥ
ꢜ
ꢚ
ꢥ
ꢩ
ꢜ
ꢝ ꢡ ꢞ ꢝꢖ ꢗꢫ ꢙꢘ ꢜ ꢤꢤ ꢢꢜ ꢚ ꢜ ꢛ ꢡ ꢝ ꢡ ꢚ ꢞ ꢦ
ꢚ
ꢚ
ꢜ
ꢗ
ꢝ
ꢪ
ꢦ
ꢔ
ꢚ
ꢙ
ꢥ
ꢠ
ꢟ
ꢝ
ꢖ
ꢙ
ꢗ
ꢢ
ꢚ
ꢙ
ꢟ
ꢡ
ꢞ
ꢞ
ꢖ
ꢗ
ꢫ
ꢥ
ꢙ
ꢡ
ꢞ
ꢗ
ꢙ
ꢝ
ꢗ
ꢡ
ꢟ
ꢡ
ꢞ
ꢞ
ꢜ
ꢚ
ꢖ
ꢤ
ꢪ
ꢖ
ꢗ
ꢟ
ꢤ
ꢠ
ꢥ
ꢡ
1
www.ti.com
ꢀ ꢁꢂꢃ ꢄꢅ
ꢆꢇ ꢈ ꢉ ꢊꢋ ꢌꢁ ꢌꢉ ꢍ ꢁꢎ ꢉ ꢏꢋ ꢎꢋ ꢐ ꢑꢉ ꢊꢍꢎꢒ ꢐ
ꢓ
SLUS195B − MARCH 1997 − REVISED NOVEMBER 2003
description (continued)
Internal circuit trimming is utilized, first to trim the impedance to a 3% tolerance, and then most importantly, to
trim the output current to a 3% tolerance, as close to the max SCSI spec as possible, which maximizes noise
margin in fast SCSI operation.
Other features include negative clamping on all signal lines to protect external circuitry from latch-up, thermal
shutdown and current limit.
This device is offered in low thermal resistance versions of the industry standard 16 pin narrow body SOIC.
connection diagrams
DP PACKAGE
(TOP VIEW)
N PACKAGE
(TOP VIEW)
LINE6
LINE5
REG
LINE7
LINE8
1
2
3
4
5
6
7
8
16
15
14
13
12
11
10
9
LINE7
LINE8
LINE6
LINE5
REG
N/C
1
2
3
4
5
6
7
8
16
15
14
13
12
LINE9
LINE9
GND*
GND*
N/C
GND*
SGND*
DISCNCT
LINE1
SGND
DISCNCT
LINE1
N/C
TRMPWR
LINE4
LINE3
11 TRMPWR
10 LINE4
LINE2
LINE2
9
LINE3
* DP package pin 5 serves as signal ground; pins 4,
12, 13 serve as heatsink/ground.
ORDERING INFORMATION
Packaged Devices
T
= T
J
A
DIL -16(N)
UC5603N
SOIC-16 (DP){
0°C to 70°C
UCUC5603DP
†
DP (SOIC−16) packages are available taped and reeled. Add TR suffix to device type (e.g.
UC5603DPTR) to order quantities of 2000 devices per reel.
2
www.ti.com
ꢀ ꢁꢂ ꢃꢄ ꢅ
ꢆ ꢇꢈ ꢉꢊꢋ ꢌꢁ ꢌꢉ ꢍꢁꢎ ꢉ ꢏꢋ ꢎ ꢋꢐꢑ ꢉ ꢊꢍꢎꢒ ꢐ
ꢓ
SLUS195B − MARCH 1997 − REVISED NOVEMBER 2003
†}
absolute maximum ratings over operating free-air temperature (unless otherwise noted)
Termpwr voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 V
Signal line voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0V to 7 V
Regulator output current . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0.5 A
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −65°C to 150°C
Operating temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . −55°C to 150°C
Lead temperature (soldering, 10 sec.) . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 300°C
†
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Unless otherwise specified all voltages are with respect to Ground. Currents are positive into, negative out of the specified terminal. Consult
Packaging Section of Unitrode Integrated Circuits databook for thermal limitations and considerations of packages.
recommended operating conditions
Termpwr voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3.8 V to 5.25 V
Signal line voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to 5 V
Disconnect input voltage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 0 V to Termpwr
electrical characteristics, these specifications apply for T = 0°C to 70°C. TRMPWR = 4.75 V
A
DISCNCT = 0 V, T = T , (unless otherwise stated)
A
J
supply current section
PARAMETER
TEST CONDITIONS
All termination lines = Open
MIN
TYP
12
MAX
18
UNITS
mA
Termpwr supply current
Power down mode
All termination lines = 0.5 V
DISCNCT = Open
200
100
220
150
mA
µA
output section (terminator lines)
PARAMETER
TEST CONDITIONS
= −5 mA to −15 mA
MIN
107
2.7
TYP
110
2.9
MAX
UNITS
Ω
Terminator impedance
Output high voltage
∆I
113
LINE
V
V
V
= 4 V,
See Note 1
V
TRMPWR
T = 25°C
−21.1 −21.9 −22.4
−20.5 −21.9 −22.4
−20.3 −21.9 −22.4
−19.8 −21.9 −22.4
−22.0 −24.0 −25.4
mA
mA
mA
mA
mA
V
J
Max output current
= 0.5 V
LINE
0°C < T < 70°C
J
T = 25°C
J
= 0.5 V,
TRMPWR = 4 V,
LINE
See Note 1
0°C < T < 70°C
Max output current
Output clamp level
J
V
= 0.2 V,
LINE
= −30 mA
TRMPWR = 4.0 V to 5.25 V
0°C < T < 70°C
J
I
−0.2 −0.05
10
0.1
400
100
LINE
V
V
= 0 to 4 V
= 5.25 V
nA
LINE
TRMPWR = 0 V to 5.25,
VREG = 0 V
µA
LINE
Output leakage
DISCNCT = 4 V
TRMPWR = 0 V to 5.25 V,
REG = Open
10
6
400
8
nA
pF
V
LINE
= 0 V to 5.25 V
Output capacitance
DISCNCT = Open
See Note 2
DP Package
NOTES: 1. Measuring each termination line while other 8 are low (0.5 V).
2. Ensured by design. Not production tested.
3
www.ti.com
ꢀ ꢁꢂꢃ ꢄꢅ
ꢆꢇ ꢈ ꢉ ꢊꢋ ꢌꢁ ꢌꢉ ꢍ ꢁꢎ ꢉ ꢏꢋ ꢎꢋ ꢐ ꢑꢉ ꢊꢍꢎꢒ ꢐ
ꢓ
SLUS195B − MARCH 1997 − REVISED NOVEMBER 2003
regulator section
PARAMETER
TEST CONDITIONS
MIN
2.8
2.8
TYP
2.9
MAX
UNITS
Regulator output voltage
3
V
V
Regulator output voltage
Line regulation
All termination lines = 5 V
TRMPWR = 4 V to 6 V
= 100 mA to −100 mA
2.9
10
3
20
50
1
mV
mV
V
Load regulation
I
20
REG
All termination lines = 0.5 V
Drop out voltage
0.7
Short circuit current
Sinking current capability
Thermal shutdown
V
V
= 0 V
−200 −400 −600
mA
mA
°C
°C
REG
= 3.5 V
200
400
170
10
600
REG
Thermal shutdown hysteresis
disconnect section
PARAMETER
Disconnect threshold
Threshold hysteresis
Input current
TEST CONDITIONS
MIN
1.3
TYP
1.5
160
10
MAX
1.7
UNITS
V
100
250
15
mV
DISCNCT = 0 V
mA
APPLICATION INFORMATION
UDG-94050
Figure 1. Typical Wide SCSI Bus Configurations Utilizing 1 UC5601 and 1 UC5603 Device
4
www.ti.com
ꢀ ꢁꢂ ꢃꢄ ꢅ
ꢆ ꢇꢈ ꢉꢊꢋ ꢌꢁ ꢌꢉ ꢍꢁꢎ ꢉ ꢏꢋ ꢎ ꢋꢐꢑ ꢉ ꢊꢍꢎꢒ ꢐ
ꢓ
SLUS195B − MARCH 1997 − REVISED NOVEMBER 2003
APPLICATION INFORMATION
UDG-94051
Figure 2. Typical Wide SCSI Bus Configurations Utilizing 3 UC5603 Devices
5
www.ti.com
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
PACKAGING INFORMATION
Orderable Device
UC5603DP
Status Package Type Package Pins Package
Eco Plan Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(3)
(4/5)
LIFEBUY
SOIC
SOIC
D
16
16
40
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
UC5603DP
UC5603DPG4
LIFEBUY
D
40
Green (RoHS
& no Sb/Br)
Level-2-260C-1 YEAR
0 to 70
UC5603DP
UC5603DPR
UC5603DPRTR
UC5603DPTR
UC5603DPTRG4
UC5603J
NRND
NRND
SOIC
SOIC
SOIC
SOIC
CDIP
PLCC
D
D
16
16
16
16
16
28
TBD
TBD
TBD
TBD
TBD
TBD
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
Call TI
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
0 to 70
OBSOLETE
OBSOLETE
OBSOLETE
NRND
D
UC5603DP
UC5603QP
D
J
UC5603QPTR
FN
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. -- The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
7-Oct-2013
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
MECHANICAL DATA
MPLC004A – OCTOBER 1994
FN (S-PQCC-J**)
PLASTIC J-LEADED CHIP CARRIER
20 PIN SHOWN
Seating Plane
0.004 (0,10)
0.180 (4,57) MAX
0.120 (3,05)
D
0.090 (2,29)
D1
0.020 (0,51) MIN
3
1
19
0.032 (0,81)
0.026 (0,66)
4
18
D2/E2
D2/E2
E
E1
8
14
0.021 (0,53)
0.013 (0,33)
0.050 (1,27)
9
13
0.007 (0,18)
M
0.008 (0,20) NOM
D/E
D1/E1
D2/E2
NO. OF
PINS
**
MIN
0.385 (9,78)
MAX
MIN
MAX
MIN
MAX
0.395 (10,03)
0.350 (8,89)
0.356 (9,04)
0.141 (3,58)
0.191 (4,85)
0.291 (7,39)
0.341 (8,66)
0.169 (4,29)
0.219 (5,56)
0.319 (8,10)
0.369 (9,37)
20
28
44
52
68
84
0.485 (12,32) 0.495 (12,57) 0.450 (11,43) 0.456 (11,58)
0.685 (17,40) 0.695 (17,65) 0.650 (16,51) 0.656 (16,66)
0.785 (19,94) 0.795 (20,19) 0.750 (19,05) 0.756 (19,20)
0.985 (25,02) 0.995 (25,27) 0.950 (24,13) 0.958 (24,33) 0.441 (11,20) 0.469 (11,91)
1.185 (30,10) 1.195 (30,35) 1.150 (29,21) 1.158 (29,41) 0.541 (13,74) 0.569 (14,45)
4040005/B 03/95
NOTES: A. All linear dimensions are in inches (millimeters).
B. This drawing is subject to change without notice.
C. Falls within JEDEC MS-018
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2013, Texas Instruments Incorporated
相关型号:
©2020 ICPDF网 联系我们和版权申明