UCC3960P [TI]
PRIMARY-SIDE STARTUP CONTROLLER;
| 型号： | UCC3960P |
| 厂家： | 
TEXAS INSTRUMENTS |
| 描述： | PRIMARY-SIDE STARTUP CONTROLLER 信息通信管理 开关 光电二极管 |
| 文件： | 总14页 (文件大小：218K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
U
C
T
C
U
2
P
9
6
0
,
U CC 39 60
C ON TR O LL ER
ą
P
R
I
M
A
R
Y
Ć
S
I
D
E
S
T
A
R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
D
Operates With Secondary-Side PWM
Control
typical operating circuit
X
V
IN
D
D
D
D
Receives Isolated PWM Command Through
a Pulse-Edge-Transformer
UCC3960
Initial Free-Running Soft-Start Up with
Duty-Cycle Clamping
2
1
FB
SS
VDD
REF
8
4
FEED
BACK
Up to 400-kHz Synchronizable Switching
Frequency
High-Current FET Drive (1.5-A Sink, 0.75-A
Source)
SOFT
START
UDG–99010
D
D
D
Overcurrent Protection
OUT
CS
7
5
6
Undervoltage Lockout with 2-V Hysteresis
Low-Current Startup
3
RT
FREQ
SET
GND
Figure 1
description
The UCC3960 primary-side startup controller is a unique solution that provides all the primary-side functions
required for a single-ended, isolated offline, switch-mode power converter that uses secondary-side PWM
control. It is usable with a wide range of secondary circuits and is especially well suitable for systems where
sophisticated handling of overload conditions is required.
Secondary-side control assumes that output voltage and current measurements are interfaced directly to an
output ground-referenced PWM stage that develops the power switch command for the supply. This digital
PWM command can then be transmitted to the primary-side power switch through a simple and low-cost
isolating pulse transformer. With secondary-side control, it is much easier to monitor and control the system load
with tightly coupled analog control loops. Load-oriented features such as output current sharing and
synchronous rectification are implemented more easily.
The UCC3960 provides all the circuitry required on the primary side of a secondary–side controlled power
supply. It features a free running 60-kHz to 360-kHz oscillator that is synchronizable to the secondary-side PWM
signal and also has the ability to accept start/stop PWM commands from the isolating pulse edge transformer.
The use of an extremely small and low-cost pulse transformer allows for higher converter bandwidth. This also
eliminates the loop-gain variations due to initial accuracy and aging of an opto-coupler feedback element or the
size penalty of a gate transformer. It also includes an undervoltage lockout circuit with 2-V hysteresis, a low
current startup with active low during UVLO, a soft-start capability, a 5-V reference and a high current power
output.
In a non-typical use, the UCC3960 can accommodate an analog feedback signal through an opto-isolator where
it can operate in voltage-mode control mode with primary-side peak current limiting.
The UCC3960 and the UCC2960 are available in the 8-pin SOIC (D) and PDIP (P) packages. A 14-pin package
version is available as UCC2961 and UCC3961 that includes additional protection features such as multimode
overcurrent protection, volt-second clamp, programmable overvoltage and undervoltage sense lines, and the
self-bias regulator.
Please be aware that an important notice concerning availability, standard warranty, and use in critical applications of
Texas Instruments semiconductor products and disclaimers thereto appears at the end of this data sheet.
Copyright 2000, Texas Instruments Incorporated
P
R
o
O
d
D
U
t
C
s
T
I
O
c
N
o
D
A
T
A
t
i
n
s
f
p
o
e
r
m
a
i
t
c
i
a
o
t
n
i
s
s
c
u
r
r
t
e
h
n
e
t
a
s
m
o
f
o
p
T
u
e
b
x
l
i
a
c
s
a
t
i
o
n
d ate.
Ins tr u men ts
P
r
u
c
n
f
o
r
m
o
c
i
f
i
o
n
p
e
r
t
e
r
s
f
s
t
a
n
d
a
r
d
w
a
r
r
a
n
t
y
.
P
r
o
d
u
c
t
i
o
n
p
r
o
c
e
s
s
i
n
g
d
o
e
s
n
o
t
n
e
c
e
s
s
a
r
i
l
y
i
n
c
l
u
d
e
t
e
s
t
i
n
g
o
f
a
l
l
p
a
r
a
m
e
t
e
r
s
.
1
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
I
C
M
2
A
9
R
6
0
Y
,
Ć
U C C 3 9 6 0
S
ą
P
R
S
I
D
E
T
A
R
TU
P
C
O
N
T
R
O
L
L
E
R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
AVAILABLE OPTIONS
D OR P PACKAGE
(TOP VIEW)
PACKAGED DEVICES
SOIC–8
SMALL OUTLINE
(D)
PDIP–8
PLASTIC DIP
(P)
SS
FB
VDD
OUT
GND
CS
1
2
3
4
8
7
6
5
TA
RT
–40_C to 85_C
0_C to 70_C
UCC2960D
UCC3960D
UCC2960P
UCC3960P
REF
†
The SOIC (D) packages are available taped and reeled. Add an R
suffix to the device type (e.g., UCC2960DR) to order quantities of
2500 devices per reel.
†‡
absolute maximum ratings over operating free-air temperature range (unless otherwise noted)
Input voltage, V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 25 V
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –1.5 A / 2 A
I(VDD)
Input current, I
Output current, I
I(VDD)
w
O
Reference current, I
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7.5 mA
REF
Output voltage: REF . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD+0.3 V
Input voltage: SS, RT, CS . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –0.3 V to VDD+0.3 V
FB . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –7.0 V to VDD+0.3 V
Operating junction temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –55_C to 150_C
J
Storage temperature range, T . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . –65_C to 150_C
stg
Lead temperature soldering 1,6 mm (1/16 inch) from case for 10 seconds . . . . . . . . . . . . . . . . . . . . . . . 300_C
†
‡
Stresses beyond those listed under “absolute maximum ratings” may cause permanent damage to the device. These are stress ratings only, and
functional operation of the device at these or any other conditions beyond those indicated under “recommended operating conditions” is not
implied. Exposure to absolute-maximum-rated conditions for extended periods may affect device reliability.
Unless otherwise indicated, voltages are reference to ground and currents are positive into and negative out of the specified terminals. Pulsed is
defined as a less than 10% duty cycle with a maximum duration of 500 µs.
w 4 nF load with 4-Ω series resistor.
2
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
T
C
U
2
P
9
6
0
,
U C C 3 9 6 0
C ON TR O LL ER
ą
PR
I
M
A
R
Y
Ć
S
I
D
E
S
T
AR
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
electrical characteristics V
= 12 V, RT = 53.3 kΩ, C
= 1 µF, C
= 0.1 mF, C
= 0.01 µF,
DD
VDD
REF
SS
R
= 4 Ω, C
= 1 nF and T = T (unless otherwise stated)
OUT
OUT
A
J
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Supply Section (VDD)
Clamp voltage
I
= 10mA
16
17.5
19
2.8
V
VDD
Operating current
No load,
C
= 0
1.8
2.3
mA
µA
OUT
Starting current
V
= 9V
100
150
200
DD
Undervoltage Lockout Section
Start threshold voltage
Hysteresis voltage
9.5
1.7
10
2
10.5
2.3
V
V
Voltage Reference Section (REF)
Reference voltage
4.75
8
5.0
3
5.25
5
V
Load regulation voltage
Line regulation voltage
Short-circuit current
Soft-Start Section (SS)
Discharge current
I
= 0 mA to –2.5 mA
= 10 V to 12 V
mV
mV
mA
REF
V
3
5
DD
10
16
SD = 4.5 V Pulsed
SD = 4.5 V Pulsed
3
–5
5
–7
1
7
–10
1.1
5.5
5
µA
µA
V
Charge current
Low–threshold voltage
Clamp threshold voltage
ON resistance
0.9
4.5
2.5
5
V
V
= 7.5 V
3.3
kΩ
DD
Current Sense Section (CS)
Pulse–by–pulse
Immediate
0.9
1.3
1
1.1
1.5
0.2
140
V
V
Threshold voltage
1.4
Input bias current
CS = 1.1 V pulsed
µA
ns
Ω
Delay time CS to OUT
ON resistance
60
100
800
600
1000
Oscillator Section
Frequency
135
150
0.02
0%
165
0.2
kHz
%/V
Frequency change with voltage
Minimum duty cycle
Maximum duty cycle
Output Section (OUT)
Low-level output voltage
High-level output voltage
Low-level output voltage during UVLO
Rise time
VDD = 10 V to 12 V
69%
72%
75%
I
I
I
= 100 mA (dc),
= –40 mA (dc) ,
= 20 mA (dc),
See Note 1
See Note 2
0.7
1.0
1.0
1.5
60
V
V
OUT
OUT
OUT
0.56
V
DD
= 7.5V
V
30
15
ns
ns
Fall time
30
NOTES: 1. OUT low, nominal of 0.7 V reflects the 3-Ω DMOS ON resistance plus 4-Ω R
.
SERIES
2. OUT high (VDD – OUT) nominal of 0.56 V reflects the 10-W HVPMOS ON resistance plus 4-Ω R
SERIES
3
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
I
C
M
2
A
9
R
6
0
Y
,
Ć
U C C 3 9 6 0
S
ą
P
R
S
I
D
E
T
A
R
TU
P
C
O
N
T
R
O
L
L
E
R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
electrical characteristics V
= 12 V, RT = 53.3 kΩ, C
= 1 µF, C
= 0.1 mF, C = 0.01 µF,
SS
DD
VDD
REF
R
= 4 Ω, C
= 1 nF and T = T (unless otherwise stated)
OUT
OUT
A
J
PARAMETER
TEST CONDITIONS
MIN
TYP
MAX
UNITS
Feedback Section (FB)
Input bias current
FB = 4.5 V,
SS = 0 V
0.4
–7.6
100
120
µA
V
Negative compliance voltage
Delay time, FB–SS to OUT, rising edge
Delay time, FB–SS to OUT, falling edge
I
= –100 mA,
SS = 0 V
FB = SS
FB = SS
–6.8
–7.2
FB
FB–SS pulsed = 2 V,
FB–SS pulsed = 2 V,
40
50
70
85
ns
ns
Terminal Functions
TERMINAL
I/O
DESCRIPTION
NAME
NO.
CS
FB
5
2
I
I
Pulse-by-pulse and shutdown overcurrent sense input pin
Control input for the signal from a secondary–side PWM
controller
GND
OUT
RT
6
7
3
4
1
8
Ground for the IC.
O
I
Drive pin for the MOSFET power switch
Sets the free-running startup oscillator frequency.
Output reference
REF
SS
O
I
Primary-side soft-start function
Power input connection
VDD
detailed descriptions
current sense (CS)
This is the pulse-by-pulse and shutdown overcurrent sense input pin. This current-sense pin triggers a
pulse-by-pulse termination anytime a 1.0-V threshold is exceeded while a signal in excess of 1.375 V on this
pin initiates a complete shutdown. Since the CS pin can be noise sensitive, it is good practice to insert a small
low-pass RC filter between this pin and the current sensor.
feedback (FB)
This is the control input for the signal from a secondary-side PWM controller whose pulse-width command has
been differentiated by the feedback pulse edge transformer (PET) into positive start and negative stop pulses.
These signals are used to turn on and off the primary power switch and must have an amplitude of at least
V
± 2.0 V (4 V peak-to-peak) for at least 25 ns per pulse and no more than 200 ns per pulse. The maximum
SS
amplitude allowed on this pin is V ± 7.0 V.
SS
output drive (OUT)
This drive pin for the N–channel MOSFET power switch sinks (1.5 A) and sources (0.75 A) fast, high-current
gate drive pulses. During shutdown, this pin is self–biased to an active low state. A minimum of 4 W should
be added in series with the output to ensure that the on-chip driver safe operating area is not exceeded. (Data
from the IRF820/830/840 family of MOSFETs, commonly available in the TO–220 package, is used to derive
this value. The gate charge needed to provide full enhancement was used to establish an equivalent
capacitance of up to 4000 pF.)
4
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
T
C
U
2
P
9
6
0
,
U C C 3 9 6 0
C ON TR O LL ER
ą
PR
IM
A
R
Y
Ć
S
I
D
E
S
T
AR
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
detailed descriptions (continued)
ground (GND)
This pin is the reference point for grounding all analog functions and must be kept as clean as possible from
all switching noise. It should be closely bypassed to VDD.
timing resistor (RT)
A resistor from this pin to GND establishes a current,
2 V
RT
I
+
SET
(1)
which is mirrored internally for several functions. It establishes the free–running startup switching frequency with
an internal capacitor according to the relationship,
9
8.0 10
fs +
RT
(2)
The startup oscillator has a rise and fall time set to limit the duty-cycle of the power switch to a maximum of 72%,
a limit that is maintained even after the feedback signal takes command. The range of RT is 22.2 kΩ to 133 kΩ,
giving a free-run frequency range range of 60 kHz to 360 kHz, respectively. Variations in the free-running
oscillator frequency overtemperature are very small. The typical temperature coefficient is –40 Hz per degree
Celsius, measured at 150 kHz.
voltage reference (REF)
This 5-V output is usable with external loads of up to 10 mA. The voltage is also the source for all internal analog
threshold settings and should be bypassed with a minimum of 0.1-µF capacitance to GND.
soft-start (SS)
The pin implements the primary-side soft-start function. This is the connection point for an external capacitor
that determines the rate of increase in commanded pulse width for the power switch at startup. It also serves
as the ac ground return for the feedback pulse transformer to provide a tracking bias for the FB input.
power (VDD)
The power input connection for all the control circuitry conducts all the gate charge current for the power FET.
It should be closely bypassed with at least 1.0-µF to GND. This pin is internally shunt regulated to clamp at
17.5 V to protect the internal components. So if a voltage source above this value is possible, external current
limiting must be provided.
5
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
I
C
M
2
A
9
R
6
0
Y
,
Ć
U C C 3 9 6 0
S
ą
P
R
S
I
D
E
T
A
R
T
U
P
CO
N
T
RO
L
LE
R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
UVLO
SOFT
START LATCH
S/D
10 V / 8 V
5.0V
8
4
VDD
1V
Q
Q
R
S
REF
GEN
VREF
OUT
CS
17 V
PWM
LATCH
STOP
PWM DRIVE
+
1 V
7
5
R
Q
FB
2
START
S
Q
5 V
+
SD
1.375 V
1 V
CURRENT
LIMIT
ISS
S/S
PWM
SS
RT
1
3
HI
LO
5 V
1.0 V
2 ISS
SYNC MAX D/C
OSCILL
RAMP
CLK
CT
GND
6
UDG–00159
Figure 1. UCC3960 Block Diagram
DETAILED DESCRIPTION
startup oscillator
The RT pin is connected to an internal 2.0 V nominal, unity-gain closed-loop amplifier that is referenced to a
voltage divider off the 5.0-V reference. When a 22.2-kΩ resistor is connected from the RT pin to GND an
approximate I
= 90 mA internal current is realized that charges the internal oscillator capacitor, approximately
RT
58 pF. I = 90 mA produces a maximum free running oscillator frequency of 360 kHz at a 70% duty cycle.
RT
When a 133.3-kΩ resistor is connected from the RT pin to GND an approximate I = 15 mA internal current
RT
is realized, which produces a minimum free running oscillator frequency of 60 kHz at approximately 72% duty
cycle. This maximum duty cycle is setup by on-chip MOSFET current mirrors that are not programmable.
Any frequency between these two limits (6:1 maximum to minimum frequency) is obtainable by linearly scaling
the RT resistance between the minimum 22.2-kΩ and maximum 133.3-kΩ values. The secondary-side PWM
frequency should be fixed at (1 / 0.9) or 1.11 times the user programmed primary-side free running oscillator
frequency for proper primary-side synchronization. Therefore, in all cases the recommended secondary-side
synchronization frequency shall be 1.11 times higher than the selected primary-side free running startup
frequency. Taking into consideration the two extreme limits for primary-side free running startup frequency, the
secondary-side operating frequency should be set between 400 kHz and 67 kHz.
6
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
T
C
U
2
P
9
6
0
,
U C C 3 9 6 0
C ON TR O LL ER
ą
PR
IM
A
R
Y
Ć
SI
DE
ST
AR
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
DETAILED DESCRIPTION
soft-start
The soft-start section contains all the circuitry required to produce a user programmable slowly increasing PWM
duty cycle, starting from 0% to a maximum of 72%. The soft-start cycle is triggered either by the initial
primary-side startup procedure or after any one of three user-programmable fault conditions and one fixed fault
condition. The PWM duty cycle increases according to the charge rate of an user-selectable external soft-start
capacitor, connected from the SS pin to GND. The SS capacitor is charged by a nominal 7-µA internal current
source.
Should the CS pin rise in voltage above 1.375 V, a soft-start cycle is triggered. The soft-start cycle disables the
output driver OUT and holds it in the low state until the capacitor connected from the SS pin to GND is discharged
below 1.0 V by an internal 5-µA current sink. After this discharge period, the PMW output OUT is enabled and
the duty cycle is allowed to slowly increase as before.
synchronization
The SS pin and the FB pin accepts the secondary-side of a small signal synchronization transformer. A series
blocking capacitor inserted in the primary-side of the synchronization transformer is intended to differentiate the
square-wave gate drive output of the secondary-side PWM controller while preventing the transformer from
saturation. The soft-start capacitor also provides an ac GND at the SS pin or the synchronization transformer
secondary. The small signal synchronization transformer provides galvanic isolation between primary and
secondary side and must have adequate voltage breakdown rating between the primary and secondary
windings.
Two comparators, with an approximate 1.0-V offset each, are connected to the FB pin to provide plus and minus
differential voltage comparison with a 2.0-V deadband between the FB and SS pins. The 2.0-V deadband
prevents inductive backswing of the small-signal transformer from giving false secondary-side pulse-edge
detection.
Enough energy must be coupled into the comparator differential inputs to ensure reliable comparator switching.
This requires sufficient voltage overdrive above the 1.0-V comparator threshold and a specified transformer
circuit time constant to provide a minimum synchronization pulse width.
On receiving the first recognizable negative going voltage pulse (turnoff command) generated from the falling
edge of the differentiated square-wave gate drive signal on the secondary-side, the PWM latch is reset and a
synchronization latch is set. After this event, all primary-side PMW driver output is slaved to the secondary-side
driver output in both frequency and duty cycle. The triggering of a soft-start cycle by a fault condition resets the
synchronization latch to again allow the internal startup oscillator to control the PWM latch.
PWM
The PWM section consists of a reset dominant SR latch with necessary logical gating on the set input to allow
control from the free running startup oscillator until feedback from the secondary-side PWM gate drive output
is detected. After the occurrence of detectable feedback from the secondary-side gate driver, the control of the
primary-side PWM latch is handed off to the secondary-side PWM controller. A nine-input OR gate on the PWM
latch reset dominant input allows the numerous fault conditions to reset the PWM latch and control from either
the startup oscillator or feedback from the secondary-side PWM output driver.
7
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
I
C
M
2
A
9
R
6
0
Y
,
Ć
U C C 3 9 6 0
S
ą
P
R
S
I
D
E
T
A
R
TU
P
CO NT RO L LE R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
DETAILED DESCRIPTION
UVLO and REF
The under voltage lockout (UVLO) circuit enables normal operation after VDD exceeds the 10.0-V turnon
threshold and permits operation until VDD falls below the 8-V turnoff threshold. While activated, the UVLO circuit
holds the PWM gate driver output (OUT) and the internal-reference buffer amplifier output REF low. To insure
proper soft-start, internal N-channel MOSFET switches discharge external capacitor connected to the SS pin
during undervoltage conditions.
The 5-V internal reference is connected to the REF pin and must be bypassed using a good quality,
high-frequency capacitor. This 5-V reference is not available externally while the chip is disabled by the under
voltage lockout circuit.
current sense
The current sense (CS) circuit monitors the voltage across a ground referenced current sense resistor,
connected between the source of the external power MOSFET and GND. The signal amplitude at the CS pin
is compared to two thresholds, (1.0 V and 1.375 V respectively), by two independent voltage comparators.
A voltage level greater than 1.0 V, but less than 1.375 V, sets the reset dominant shutdown latch and resets the
PWM latch. The SD latch is reset when the startup oscillator arrives at its 4.0-V threshold.
During the OFF period of the PWM latch, any capacitance connected to the CS pin is discharged to GND
potential by an internal 800-Ω device.
VDD clamp
To insure that the absolute maximum voltage ratings of internal devices are not violated, an internal shunt
voltage regulator is provided to clamp the VDD pin at a nominal 17.5-V maximum voltage. Similarly to other
shunt or Zener-like voltage regulator circuits, the current through the internal VDD clamp must be limited below
the maximum current level indicated in the datasheet. In addition to limiting the current through the clamp circuit,
the maximum power dissipation capability of the particular package used in the application has to be
considered.
OUT driver
An internal output driver (OUT) is provided to drive the gate of an external N–channel power MOSFET. The
output driver consists of a nominal 4.0-Ω ON-resistance P-channel MOSFET for turnon, and a nominal 2.0-Ω
ON-resistance D–channel MOSFET used during the turn–off of the external MOSFET transistor. An external
series gate resistance is specified to maintain an acceptable SOA (Safe Operating Area) for the DMOS device
of the internal output driver. As discussed in the UVLO section before, the under voltage lockout (UVLO) circuit
holds the PWM gate driver output low while UVLO conditions exists.
8
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
T
C
U
2
P
9
6
0
,
U C C 3 9 6 0
C ON TR O LL ER
ą
PR
IM
A
R
Y
Ć
SI
DE
ST
AR
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
APPLICATION INFORMATION
The evaluation circuit of the UCC3960 as the primary-side startup circuit and UC38C45 as the secondary-side
controller is shown in Figure 2.
UP4–101
MUR610
OUT
V
IN
470 F
F
470
10
MUR110
4.7 k
IRF530
12 V
UCC38C45
VREF COMP 1
0.1 F 36 k
36 k
1 k
8
7
6
5
VDD
OUT
GND
FB
CS
RT
2
3
4
0.5
10k
4.7 F
6.8 k
1000 pF
1000 pF
0.1 F
12 V
UCC3960
2.7 nF
8
7
VDD
OUT
SS
FB
1
2
200
L = 5.4 H
M
1 F
RT 80 k
6
5
GND ISET
CS REF
3
4
1 F
300
100 pF
0.1 F
UDG–99099
Figure 2. Evaluation Circuit UCC3960
9
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
I
C
M
2
A
9
R
6
0
Y
,
Ć
U C C 3 9 6 0
S
ą
P
R
S
I
D
E
T
A
R
TU
P
CO NT RO L LE R
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
APPLICATION INFORMATION
pulse-edge transmission circuit
The UCC3960 uses a pulse-edge-transmission (PET) circuit to transmit isolated gate-pulse information from
the secondary-side controller. It is important for the PET circuitry to have proper frequency response and
adequately high damping (low Q-factor) in order to precent excessive overshoot. The circuit is shown in
Figure 3.
25 ns < T < 200 ns
C1
R1
VFB
FB
UCC3960
SS
1
4
+
–
V2P
0
R2
VSS+1.0
VSS
VSS–1.0
t
SECONDARY
GATE PULSE
C
SS
L
M
25 ns < T < 200 ns
UDG–99097
Figure 3. Pulse Edge Transmission (PET) Circuit
The pulse width measured at the FB pin must be less than 25 ns when measured at 1 V above the soft-start
voltage and 200 ns when measured at 1 V below the soft-start voltage. The feedback (FB) voltage must not be
overdriven by more than 5 V above or 5 V below the soft-start voltage. In order to prevent false triggering, the
feedback voltage must not ring below the soft-start voltage by more than ±0.9 V. This can be met if the PET
circuit has a resonant frequency of 880 kHz and a Q of 0.25. The following values meet those specifications
for a 12-V segondary gate pulse signal, over the full range of UCC3960 operating frequencies.
T1
R1
C1
R2
1:1 turns ratio, LM = 5.4-µH, Ferronics 11–622J, N1 = N2 = 4 turns
300 Ω
2700 pF
200 Ω
Pulse-edge-transmission (PET) circuits in standard surface-mount packages are available from Pulse
Engineering (Part #PA0128, Part #PA0115) and from Cooper Electronic Technologies (Coiltronix),
(Part #CTX01–15157).
10
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
U
C
T
C
U
2
P
9
6
0
,
U C C 3 9 6 0
C ON TR O LL ER
ą
PR
IM
A
R
Y
Ć
S
I
D
E
ST
AR
SLUS430A – APRIL 1999 – REVISED DECEMBER 2000
PARAMETER MEASUREMENT INFORMATION
OPERATING WAVEFORMS
DURING OVERLOAD
NORMAL OPERATING WAVEFORMS
Figure 4
Figure 5
OPERATING WAVEFORMS
DURING NO LOAD
Figure 6
ADDITIONAL REFERENCES
1. Dennis, Mark and Michael Madigan, 50-W Forward Converter with Synchronous Rectification and
Secondary-Side Control, SEM–1300, Topic 4, Texas Instruments Literature Number SLUP002.
11
POST OFFICE BOX 655303 • DALLAS, TEXAS 75265
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
PACKAGING INFORMATION
Orderable Device
UCC2960D
Status Package Type Package Pins Package
Eco Plan
Lead/Ball Finish
MSL Peak Temp
Op Temp (°C)
-40 to 85
-40 to 85
0 to 70
Device Marking
Samples
Drawing
Qty
(1)
(2)
(6)
(3)
(4/5)
ACTIVE
SOIC
SOIC
SOIC
SOIC
PDIP
D
8
8
8
8
8
75
Green (RoHS
& no Sb/Br)
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
CU NIPDAU
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
Level-2-260C-1 YEAR
N / A for Pkg Type
UCC2960
UCC2960DG4
UCC3960D
ACTIVE
ACTIVE
ACTIVE
ACTIVE
D
D
D
P
75
75
75
50
Green (RoHS
& no Sb/Br)
UCC2960
UCC3960
UCC3960
UCC3960P
Green (RoHS
& no Sb/Br)
UCC3960DG4
UCC3960P
Green (RoHS
& no Sb/Br)
0 to 70
Green (RoHS
& no Sb/Br)
0 to 70
(1) The marketing status values are defined as follows:
ACTIVE: Product device recommended for new designs.
LIFEBUY: TI has announced that the device will be discontinued, and a lifetime-buy period is in effect.
NRND: Not recommended for new designs. Device is in production to support existing customers, but TI does not recommend using this part in a new design.
PREVIEW: Device has been announced but is not in production. Samples may or may not be available.
OBSOLETE: TI has discontinued the production of the device.
(2) Eco Plan - The planned eco-friendly classification: Pb-Free (RoHS), Pb-Free (RoHS Exempt), or Green (RoHS & no Sb/Br) - please check http://www.ti.com/productcontent for the latest availability
information and additional product content details.
TBD: The Pb-Free/Green conversion plan has not been defined.
Pb-Free (RoHS): TI's terms "Lead-Free" or "Pb-Free" mean semiconductor products that are compatible with the current RoHS requirements for all 6 substances, including the requirement that
lead not exceed 0.1% by weight in homogeneous materials. Where designed to be soldered at high temperatures, TI Pb-Free products are suitable for use in specified lead-free processes.
Pb-Free (RoHS Exempt): This component has a RoHS exemption for either 1) lead-based flip-chip solder bumps used between the die and package, or 2) lead-based die adhesive used between
the die and leadframe. The component is otherwise considered Pb-Free (RoHS compatible) as defined above.
Green (RoHS & no Sb/Br): TI defines "Green" to mean Pb-Free (RoHS compatible), and free of Bromine (Br) and Antimony (Sb) based flame retardants (Br or Sb do not exceed 0.1% by weight
in homogeneous material)
(3) MSL, Peak Temp. - The Moisture Sensitivity Level rating according to the JEDEC industry standard classifications, and peak solder temperature.
(4) There may be additional marking, which relates to the logo, the lot trace code information, or the environmental category on the device.
(5) Multiple Device Markings will be inside parentheses. Only one Device Marking contained in parentheses and separated by a "~" will appear on a device. If a line is indented then it is a continuation
of the previous line and the two combined represent the entire Device Marking for that device.
Addendum-Page 1
PACKAGE OPTION ADDENDUM
www.ti.com
10-Jun-2014
(6) Lead/Ball Finish - Orderable Devices may have multiple material finish options. Finish options are separated by a vertical ruled line. Lead/Ball Finish values may wrap to two lines if the finish
value exceeds the maximum column width.
Important Information and Disclaimer:The information provided on this page represents TI's knowledge and belief as of the date that it is provided. TI bases its knowledge and belief on information
provided by third parties, and makes no representation or warranty as to the accuracy of such information. Efforts are underway to better integrate information from third parties. TI has taken and
continues to take reasonable steps to provide representative and accurate information but may not have conducted destructive testing or chemical analysis on incoming materials and chemicals.
TI and TI suppliers consider certain information to be proprietary, and thus CAS numbers and other limited information may not be available for release.
In no event shall TI's liability arising out of such information exceed the total purchase price of the TI part(s) at issue in this document sold by TI to Customer on an annual basis.
Addendum-Page 2
IMPORTANT NOTICE
Texas Instruments Incorporated and its subsidiaries (TI) reserve the right to make corrections, enhancements, improvements and other
changes to its semiconductor products and services per JESD46, latest issue, and to discontinue any product or service per JESD48, latest
issue. Buyers should obtain the latest relevant information before placing orders and should verify that such information is current and
complete. All semiconductor products (also referred to herein as “components”) are sold subject to TI’s terms and conditions of sale
supplied at the time of order acknowledgment.
TI warrants performance of its components to the specifications applicable at the time of sale, in accordance with the warranty in TI’s terms
and conditions of sale of semiconductor products. Testing and other quality control techniques are used to the extent TI deems necessary
to support this warranty. Except where mandated by applicable law, testing of all parameters of each component is not necessarily
performed.
TI assumes no liability for applications assistance or the design of Buyers’ products. Buyers are responsible for their products and
applications using TI components. To minimize the risks associated with Buyers’ products and applications, Buyers should provide
adequate design and operating safeguards.
TI does not warrant or represent that any license, either express or implied, is granted under any patent right, copyright, mask work right, or
other intellectual property right relating to any combination, machine, or process in which TI components or services are used. Information
published by TI regarding third-party products or services does not constitute a license to use such products or services or a warranty or
endorsement thereof. Use of such information may require a license from a third party under the patents or other intellectual property of the
third party, or a license from TI under the patents or other intellectual property of TI.
Reproduction of significant portions of TI information in TI data books or data sheets is permissible only if reproduction is without alteration
and is accompanied by all associated warranties, conditions, limitations, and notices. TI is not responsible or liable for such altered
documentation. Information of third parties may be subject to additional restrictions.
Resale of TI components or services with statements different from or beyond the parameters stated by TI for that component or service
voids all express and any implied warranties for the associated TI component or service and is an unfair and deceptive business practice.
TI is not responsible or liable for any such statements.
Buyer acknowledges and agrees that it is solely responsible for compliance with all legal, regulatory and safety-related requirements
concerning its products, and any use of TI components in its applications, notwithstanding any applications-related information or support
that may be provided by TI. Buyer represents and agrees that it has all the necessary expertise to create and implement safeguards which
anticipate dangerous consequences of failures, monitor failures and their consequences, lessen the likelihood of failures that might cause
harm and take appropriate remedial actions. Buyer will fully indemnify TI and its representatives against any damages arising out of the use
of any TI components in safety-critical applications.
In some cases, TI components may be promoted specifically to facilitate safety-related applications. With such components, TI’s goal is to
help enable customers to design and create their own end-product solutions that meet applicable functional safety standards and
requirements. Nonetheless, such components are subject to these terms.
No TI components are authorized for use in FDA Class III (or similar life-critical medical equipment) unless authorized officers of the parties
have executed a special agreement specifically governing such use.
Only those TI components which TI has specifically designated as military grade or “enhanced plastic” are designed and intended for use in
military/aerospace applications or environments. Buyer acknowledges and agrees that any military or aerospace use of TI components
which have not been so designated is solely at the Buyer's risk, and that Buyer is solely responsible for compliance with all legal and
regulatory requirements in connection with such use.
TI has specifically designated certain components as meeting ISO/TS16949 requirements, mainly for automotive use. In any case of use of
non-designated products, TI will not be responsible for any failure to meet ISO/TS16949.
Products
Applications
Audio
www.ti.com/audio
amplifier.ti.com
dataconverter.ti.com
www.dlp.com
Automotive and Transportation www.ti.com/automotive
Communications and Telecom www.ti.com/communications
Amplifiers
Data Converters
DLP® Products
DSP
Computers and Peripherals
Consumer Electronics
Energy and Lighting
Industrial
www.ti.com/computers
www.ti.com/consumer-apps
www.ti.com/energy
dsp.ti.com
Clocks and Timers
Interface
www.ti.com/clocks
interface.ti.com
logic.ti.com
www.ti.com/industrial
www.ti.com/medical
Medical
Logic
Security
www.ti.com/security
Power Mgmt
Microcontrollers
RFID
power.ti.com
Space, Avionics and Defense
Video and Imaging
www.ti.com/space-avionics-defense
www.ti.com/video
microcontroller.ti.com
www.ti-rfid.com
www.ti.com/omap
OMAP Applications Processors
Wireless Connectivity
TI E2E Community
e2e.ti.com
www.ti.com/wirelessconnectivity
Mailing Address: Texas Instruments, Post Office Box 655303, Dallas, Texas 75265
Copyright © 2014, Texas Instruments Incorporated
相关型号：
©2020 ICPDF网 联系我们和版权申明