UTCRCT02 [UTC]
Encoder For Remote Controller With Five Functions CMOS IC; 编码器遥控器采用五功能的CMOS IC型号: | UTCRCT02 |
厂家: | Unisonic Technologies |
描述: | Encoder For Remote Controller With Five Functions CMOS IC |
文件: | 总11页 (文件大小:148K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
UTCRCT02
CMOS IC
Encoder For Remote Controller
With Five Functions
DESCRIPTION
The chip can be used with the decoder RCR02 to provide a
complete control functions to the remote-controlled toy. The
RCT02 has five input pins corresponding with the five
function buttons i.e, forward, backward, rightward, leftward
and turbo. The encoding circuit in the RCT02 sends digital
codes to the two output pins SO and SC. The digital codes
correspond to the definite function buttons or their
combinations. The SO and SC outputs are used in wireless
and infra-red applications respectively.
There is an internal oscillator in the RCT02. By adding an
external resistor conveniently, the oscillator will be
constructed. The oscillator frequency can be adjusted by the
external resistor. The relative error between the frequencies
of the two on chip oscillators in the RCT02 and RCR02 must
be less than ±25%.
SOP-14
DIP-14
The auto-power-off function is achieved by an internal
counter. When the RCT02 is powered on, the counter is reset
and begin to count. Any action of push down or release the
function button also reset the counter. The PC pin will keep
on a high level until the counter counts up to about 4 minutes.
The PC output is used to control on/off state of the external
power supply. Pressing OFF button can also shut down the
power supply. Press on any function button will wake up the
chip promptly.
FEATURES
*Five input pins used for five control buttons
*Operating power-supply voltage range: 2.5 to 5.0V
*Auto-power-off if no press on any button in 4 minutes or
continuously press on any button over 4 minues
*Manual-power-on/off with ON/OFF button
*One output pin used for external power control
*Press on any button as wake up
*On-chip oscillator with an external resistor
*Low operating current
*Few external components needed
1
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
Logic Block Diagram
OFF
OSCI
Timing
Generator
4 Minutes
Counter
Oscillator
PC
OSCO
RIGHTB
LEFTB
TURBOB
SO
SC
Input
Circuit
Encoding
Circuit
Output
Circuit
FORWARDB
BACKWARDB
Product Pin Configuration and Pin Description
LEFTB
OFF
RIGHTB
TESTB
1
2
3
14
13
12
OSCI
GND
BACKWARDB
OSCO
PC
4
5
6
11
10
9
FORWARDB
TURBOB
VDD
SO
SC
8
7
Pin No.
Pin Name
RIGHTB
TESTB
GND
Description
1
2
3
The rightward function will be selected, if this pin is connected to GND
This pin is used for testing mode
Negative power supply
4
5
BACKWARDB The backward function will be selected, if this pin is connected to GND
FORWARDB The forward function will be selected, if this pin is connected to GND
6
7
8
9
TURBOB
SC
SO
VDD
The turbo function will be selected, if this pin is connected to GND
Output pin of the encoding signal with carrier frequency
Output pin of the encoding signal without carrier frequency
Positive power supply
10
11
12
13
14
PC
Power control output pin
Oscillator output pin
Oscillator input pin
This pin is used to shut down the external power supply
The leftward function will be selected, if this pin is connected to GND
OSCO
OSCI
OFF
LEFTB
2
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
ABSOLUTE MAXIMUM RATINGS
PARAMETER
SYMBOL
VIN
VALUE
-0.5 ~ +5.5
-0.5 ~ +5.5
-0.5 ~ +5.5
20
500
-10 to +40
-25 to +85
UNIT
V
DC Input Voltage
Supply Voltage to Ground Potential(Inputs &VDD Only)
Supply Voltage to Ground Potential(Outputs &D/O Only)
DC Output Current
Power Dissipation
Ambient Temperature With Power Applied
Storage Temperature
V
V
mA
mW
°C
Io
PD
TA
TSTG
°C
DC ELECTRICAL CHARACTERISTICS (Over the operating rating, TA= -10°C~ +40°C,VDD=4.0V±10%)
PARAMETER
Operating Voltage
Supply Current
Standby Current
Input Current
Input Low Voltage
Output High Voltage
Output High Current
Output Low Voltage
Output Low Current
SYMBOL
TEST CONDITIONS
MIN
2.5
TYP
4.0
MAX UNITS
VDD
IDD
ISTB
IIN
5.0
300
10
60
0.5
V
µA
µA
µA
V
Output unloaded
OFF state
Pin 1,4,5,6,14
Guaranteed Logic Low Level
IOUT=1.0mA
VOUT=1.4V
IOUT=150µA
VOUT=0.5V
VIL
VOH
IOH
VOL
IOL
3.5
-4.0
V
mA
V
0.5
150
µA
AC ELECTRICAL CHARACTERISTICS (Over the operating rating, TA= -10°C to +40°C,VDD=4.0V±10%)
PARAMETER
SYMBOL
Fosc
TFUN
TEST CONDITIONS
TA=25°C,R=200KΩ
FOSC=102~ 154KHz
FOSC=102~ 154KHz
FOSC=102~ 154KHz
FOSC=102~ 154KHz
MIN
102
0.8
1.6
51
TYP
128
1
21
64
4
MAX UNITS
Oscillator Frequency (Note 1)
Cycle Time of Function Code
Cycle Time of Start Code
Carrier Frequency of SC Pin
Time of Auto-Power-Off (Note 2)
154
1.2
2.4
77
KHz
ms
ms
KHz
min.
TSTA
FCSC
TOFF*
3.2
4.8
Note 1: The relative error between the frequencies of the two on-chip oscillators in the RCT02 and RCR02 must be
less than±25%.
Note 2: When adjust the external oscillator resistor, the auto-power-off time will vary relevantly.
3
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
CODE FORMAT (W1 is used for function codes, W2 for start codes)
W1
W1:1KHz 50% Duty Cycle Typical
W2
W2: 500Hz 75% Duty Cycle Typical
WORD FORMAT
Start Code: 4W2
Function Code: n' W1
1 Word
ENCODING TIMING
W2 W2 W2 W2 (n)’ W1 W2 W2 W2 W2 (n)’ W1 W2 W2 W2 W2 (n)’ W1 W2 W2 W2 W2 (n)’W1- - - - - - - -
Press any buttons
1
2
3
14 15
Encoding output
1st word 2nd word
Function Codes
last word
End Codes
4
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
Number of Function Codes (n) W1
Function Buttons
(End Code)
4
10
16
22
28
34
40
46
52
58
64
Forward
Forward & Turbo
Turbo
(Turbo/Forward) & Left
(Turbo/Forward) & Right
Backward
Backward & Right
Backward & Left
Left
Right
PC Output Timing
VDD
OFF
PC
VDD
OFF
PC
4 Minutes
4 Minutes
Note: There is no press on any function button.
VDD
Press Function
buttons
PC
4 Minutes
4 Minutes
4 Minutes
5
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
BLOCK DIAGRAM OF APPLICATION CIRCUIT (1)
5~12V
1
14
13
LEFTB
OFF
RIGHTB
TESTB
2
POW ER
OFF
3
4
12
OSCI
GND
BACK
FOR
11
10
OSCO
PC
5
6
9
8
VDD
SO
TURBOB
SC
7
+
RCT02
RF
TRANSMITTER
Note: 1.The power supply for above circuit should be 5.0V to 12V.
2.This circuit is for wireless application.
6
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
BLOCK DIAGRAM OF APPLICATION CIRCUIT (2)
2.5~5.0V
1
2
14
13
LEFTB
OFF
RIGHTB
TESTB
POW ER
OFF
3
4
12
11
OSCI
GND
BACK
FOR
OSCO
PC
5
6
10
9
8
VDD
SO
TURBOB
SC
7
﹢
RCT02
RF
TRANSMITTER
Note: 1.The power supply for above circuit should be 2.5V to 5.0V.
2. This circuit is for wireless application.
7
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
BLOCK DIAGRAM OF APPLICATION CIRCUIT (3)
5~12V
RCT02
1
14
RIGHTB
LEFTB
2
3
13
POW ER
OFF
TESTB
OFF
12
GND
OSCI
11
10
4
5
BACK
FOR
OSCO
PC
6
7
9
8
TURBOB
SC
VDD
SO
+
+
INFRA-RED
DIODES
Note: 1.The power supply for above circuit should be 5.0V to 12V.
2.This circuit is for infra-red application.
8
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
BLOCK DIAGRAM OF APPLICATION CIRCUIT (4)
2.5~5.0V
1
14
13
LEFTB
OFF
RIGHTB
TESTB
2
POW ER
OFF
3
12
11
OSCI
GND
BACK
FOR
4
5
OSCO
PC
10
6
7
9
8
VDD
SO
TURBOB
SC
+
RCT02
+
INFRA - RED
DIODES
Note: 1.The power supply for above circuit should be 2.5V to 5.0V.
2.This circuit is for infra-red application.
9
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
TYPICAL APPLICATION FOR TRANSIMIT CIRCUIT WITH 9V BATTERY
R11
10M
V7
4148
C12 C11
0.01u 4.7u
R9
330
V5
8550
POW ER
OFF
R7200K
V4
4.7V
R12
10M
R8
3.9K
B1
9V
V6
9013
S6
S5
R2
4.7K
R10
1K
V3
LED
R4
6.8K
A1
L2
2.2u
ANTENNA
C8
0.02u
C4
150
L4
L3
6.8u
RCT02
L1
2.2u
R3
220K
V1
9014
C2
150
C1
100
CR1
27.145
C3
47
C9
68
R5
3.3K
C7
68
R1
100
C6
0.2 u
V2
9014
R6
100
S1
S2 S3
S4
10
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
UTCRCT02
CMOS IC
TYPICAL APPLICATION FOR TRANSIMIT CIRCUIT WITH 9V BATTERY
UTC assumes no responsibility for equipment failures that result from using products at values that
exceed, even momentarily, rated values (such as maximum ratings, operating condition ranges, or
other parameters) listed in products specifications of any and all UTC products described or contained
herein. UTC products are not designed for use in life support appliances, devices or systems where
malfunction of these products can be reasonably expected to result in personal injury. Reproduction in
whole or in part is prohibited without the prior written consent of the copyright owner. The information
presented in this document does not form part of any quotation or contract, is believed to be accurate
and reliable and may be changed without notice.
11
UTC UNISONIC TECHNOLOGIES CO., LTD.
QW-R502-002,C
相关型号:
©2020 ICPDF网 联系我们和版权申明