TFS170G [VECTRON]

Filter specification; 过滤器规格
TFS170G
型号: TFS170G
厂家: Vectron International, Inc    Vectron International, Inc
描述:

Filter specification
过滤器规格

过滤器
文件: 总5页 (文件大小:163K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Filename: tfs 170g.doc  
Version 1.3  
22.11.2004  
VI TELEFILTER  
Filter specification  
TFS 170G  
1/5  
Measurement condition  
Ambient temperature:  
Input power level:  
Terminating impedance: *  
Input:  
23  
0
°C  
dBm  
86 || -36 pF  
98 || -28 pF  
Output:  
Characteristics  
Remark:  
The reference level for the relative attenuation a of the TFS 170G is the maximum attenuation in the pass band. The maximum attenuation in the pass  
rel  
band is defined as the insertion loss a . The nominal frequency fN is fixed at 170,6 MHz without any tolerance or limit. The values of relative attenuation  
e
a
are guaranteed for the whole operating temperature range. The frequency shift of the filter in the operating temperature range is included in the  
rel  
production tolerance scheme.  
D a t a  
typ. value  
tolerance / limit  
Insertion loss  
ae  
4,9 dB  
max.  
8,0 dB  
(Reference level)  
Nominal frequency  
f
-
170,6 MHz  
N
Passband  
Pass band ripple  
PB  
-
f
±
90  
1,0 dB  
kHz  
N
0,3 dB  
max.  
Centre frequency  
170,6 MHz  
-
Relative attenuation  
a
rel  
fN ± 90 kHz ... fN ± 200  
kHz  
-0,1 dB  
min.  
min.  
-1  
1
dB**  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
fN  
fN  
fN  
fN  
fN  
fN  
fN  
±
±
±
±
±
±
±
0,2 MHz ... fN ±  
0,4 MHz ... fN ±  
0,6 MHz ... fN ±  
0,8 MHz ... fN ±  
1,6 MHz ... fN ±  
0,4 MHz  
0,6 MHz  
0,8 MHz  
1,6 MHz  
2
23  
35  
45  
48  
55  
60  
65  
70  
70  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
dB  
min. 13  
min. 27  
min. 40  
min. 43  
min. 47  
min. 50  
min. 45  
min. 40  
min. 40  
3
MHz  
3
MHz ... fN ±  
5,8 MHz  
5,8 MHz ... fN ±  
35  
75  
75 MHz ... fN - 170  
fN + 75 MHz ...  
MHz  
MHz  
MHz  
GHz  
fN ± 35 MHz ... fN ±  
fN  
-
2
Group delay variation in PB  
VSWR in PB  
0,28 µs  
max.  
max.  
1
µs  
1,6 : 1  
2 : 1  
Temperature coefficient of frequency Tcf ****  
Frequency inversion temperature T0  
Operating temperature range  
-0,036 ppm/K2  
-
-
45  
-
°C  
- 10 °C .. +  
- 40 °C.. +  
85 °C  
125 °C  
Storage temperature range  
-
Input power level :  
-
max. 10,0 dBm  
*) The terminating impedances depend on parasitics and q-values of matching elements and the board used, and are to be understood as reference  
values only. Should there be additional questions do not hesitate to ask for an application note or contact our design team.  
**) reference is max. loss in PB  
***)f(Hz) = TC (ppm/K) x (T-T0)² x f (MHz)  
f
To  
Generated:  
Checked / approved:  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 170g.doc  
Version 1.3  
22.11.2004  
VI TELEFILTER  
Filter specification  
TFS 170G  
2/5  
Filter characteristic  
0
0
-1  
8.77  
8.02  
7.27  
6.52  
5.77  
5.02  
4.27  
3.52  
2.77  
2.02  
1.27  
-10  
-20  
-30  
-40  
-50  
-60  
-70  
-80  
-90  
-100  
-2  
-3  
-4  
-5  
-6  
-7  
-8  
-9  
-10  
160.6 162.6 164.6 166.6 168.6 170.6 172.6 174.6 176.6 178.6 180.6  
frequency in MHz  
170.35170.4 170.45170.5 170.55 170.6 170.65 170.7 170.75 170.8 170.85  
frequency in MHz  
Construction and pin connection  
(All dimensions in mm)  
10  
6
1
2
3
4
5
6
7
8
Input RF Return  
Ground  
Ground  
Ground  
Output  
Output RF Return  
Ground  
Ground  
TFS 170G  
S48  
1
5
+0,20  
-0,10  
19  
Date code  
9
Ground  
10  
Input  
1,02  
1
Date code: Year + week  
S
T
U
...  
2004  
2005  
2006  
1,91  
7,62  
50 Ohm Test circuit  
L2  
L1  
10  
1
5
6
SAW  
C2  
C1  
2, 3, 4, 7, 8, 9  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 170g.doc  
Version 1.3  
22.11.2004  
VI TELEFILTER  
Filter specification  
TFS 170G  
3/5  
Stability characteristics  
After the following tests the filter shall meet the whole specification:  
1. Shock:  
500g, 18 ms, half sine wave, 3 shocks each plane;  
DIN IEC 68 T2 - 27  
2. Vibration:  
10 Hz to 500 Hz, 0,35 mm or 5g respectively, 1 octave per min, 10 cycles per plan, 3 plans;  
DIN IEC 68 T2 - 6  
3. Damp heat:  
(cycle)  
25 °C to 55°C / 95% r.H. / 10 cycles  
DIN IEC 68 - 2 – 30 Db  
4. Resistance to  
solder heat (reflow):  
max. 2 times reflow process;  
for temperature conditions refer to the attached "Air reflow temperature conditions" on page 4;  
Packing  
Tape & Reel:  
IEC 286 – 3, with exeption of value for N and minimum bending radius;  
tape type II, embossed carrier tape with top cover tape on the upper side;  
max. pieces of filters peer reel:  
reel of empty components at start:  
reel of empty components at start including leader:  
trailer:  
2000  
min. 300 mm  
min. 500 mm  
min. 300 mm  
Pull Off Direction  
P1  
P2  
Tape (all dimensions in mm)  
t
Do  
Po  
Ao  
Date Code  
W
: 32,00 ± 0,3  
Po  
Do  
E
:
:
:
4,00 ± 0,1  
1,50 +0,1/-0  
1,75 ± 0,1  
F
: 14,20 ± 0,1  
2,00 ± 0,1  
: 12,00 ± 0,1  
P2  
P1  
D1(min)  
Ao  
Bo  
So  
Ct  
:
Ko  
:
:
2,00  
7,10 ± 0,1  
: 19,60 ± 0,1  
: 28,40 ± 0,1  
: 25,5 ± 0,1  
PIN Marker  
Type  
D1  
W
2
Reel (all dimensions in mm)  
A
:330  
W1  
: 32,4 +2/-0  
W2(max) : 38,4  
N(min)  
C
:100  
: 13,0 +0,5/-0,2  
C
A
N
W
1
The minimum bending radius is 45 mm.  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 170g.doc  
Version 1.3  
22.11.2004  
VI TELEFILTER  
Filter specification  
TFS 170G  
4/5  
Air reflow temperature conditions  
Conditions  
Exposure  
Average ramp-up rate (30°C to 217°C)  
> 100°C  
less than 3°C/second  
between 300 and 600 seconds  
> 150°C  
> 217°C  
Peak temperature  
between 240 and 500 seconds  
between 30 and 150 seconds  
max. 260°C  
Time within 5°C of actual peak temperature  
Cool-down rate (Peak to 50°C)  
Time from 30°C to Peak temperature  
between 10 and 30 seconds  
less than 6°C/second  
no greater than 300 seconds  
Chip-mount air reflow profile  
Temperature / °C  
max. 260°C  
217°C  
Time / s  
max. 300 s  
10 ... 30 s  
30 ... 150 s  
History  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  
Filename: tfs 170g.doc  
Version 1.3  
22.11.2004  
VI TELEFILTER  
Filter specification  
TFS 170G  
5/5  
Version  
Reason of Changes  
Name  
Date  
1.0  
1.1  
- identical with specification from hudson  
- customer specification (requierment)  
Max. input power instead of  
Sabah  
Sabah  
08.10.1999  
28.03.2000  
10 dBm  
is 20 dBm  
VSWR : instead of 1.7 is 2.0:1  
Rejection (± 200 KHz): instead of 0.50 dB is 0 dB  
Impedance Value: Input corrected from 20 Ω⎟⎟ -10.9 pF to 86 ⎟⎟ -36 pF  
Outpu: corrected from 20 Ω⎟⎟ -5.5pF to 98 ⎟⎟ -28 pF  
Sabah  
30.03.2000  
1.2  
1.3  
- No necessity for IP3 –measurement  
- The sprocket holes: instead of the right side of the tape is on the left  
side of the tape (according to customer requirement, e mail from: 7. Juli.00)  
- Input power changed from 20 dBm to 10 dBm  
Sabah  
Pfeiffer  
12.07.2000  
22.11.2004  
- typical values, filter characteristic added  
- air reflow temperature conditions modified  
Tele Filter GmbH  
Potsdamer Straße 18  
D 14 513 TELTOW / Germany  
Tel: (+49) 3328 4784-0 / Fax: (+49) 3328 4784-30  
E-Mail: tft@telefilter.com  
VI TELEFILTER reserves the right to make changes to the product(s) and/or information contained herein without notice. No liability is  
assumed as a result of their use or application. No rights under any patent accompany the sale of any such product(s) or information.  

相关型号:

TFS170K

Filter Specification
VECTRON

TFS170L

Filter Specificationl
VECTRON

TFS170N

Filter specification
VECTRON

TFS170N_06

Filter specification
VECTRON

TFS171

Specification
VECTRON

TFS171A

Filter Specification
VECTRON

TFS172A

Filter specification
VECTRON

TFS172B

Filter specification
VECTRON

TFS173A

Filter Specification
VECTRON

TFS174

Filter Specification
VECTRON

TFS1747

VI TELEFILTER
VECTRON

TFS1747_07

VI TELEFILTER
VECTRON