TSOP58256SS1BS12Z [VISHAY]
Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B;
| 型号： | TSOP58256SS1BS12Z |
| 厂家： | 
VISHAY |
| 描述： | Photo IC, TRANSISTOR-STAGE OUTPUT PHOTO IC,LED-7B 输出元件 |
| 文件： | 总7页 (文件大小：133K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
New TSOP582.., TSOP584..
Vishay Semiconductors
IR Receiver Modules for Remote Control Systems
FEATURES
• Low supply current
• Photo detector and preamplifier in one package
• Internal filter for PCM frequency
• Improved shielding against EMI
• Supply voltage: 2.7 V to 5.5 V
• Improved immunity against ambient light
• Insensitive to supply voltage ripple and noise
19026
• Compliant to RoHS directive 2002/95/EC and in
accordance to WEEE 2002/96/EC
MECHANICAL DATA
Pinning:
DESCRIPTION
The TSOP582.., TSOP584.. series are miniaturized
receivers for infrared remote control systems. A PIN diode
and a preamplifier are assembled on a lead frame, the epoxy
package acts as an IR filter.
1 = OUT, 2 = GND, 3 = VS
The demodulated output signal can be directly decoded by a
microprocessor. The TSOP582.. is compatible with all
common IR remote control data formats. The TSOP584.. is
optimized to suppress almost all spurious pulses from
energy saving fluorescent lamps but will also suppress some
data signals.
This component has not been qualified according to
automotive specifications.
PARTS TABLE
CARRIER FREQUENCY
STANDARD APPLICATIONS (AGC2/AGC8)
VERY NOISY ENVIROMENTS (AGC4)
30 kHz
33 kHz
36 kHz
36.7 kHz
38 kHz
40 kHz
56 kHz
TSOP58230
TSOP58233
TSOP58236
TSOP58237
TSOP58238
TSOP58240
TSOP58256
TSOP58430
TSOP58433
TSOP58436
TSOP58437
TSOP58438
TSOP58440
TSOP58456
BLOCK DIAGRAM
APPLICATION CIRCUIT
17170_7
16833_5
R1
3
Transmitter
with
TSALxxxx
IR receiver
VS
+ VS
GND
VS
33 kΩ
C1
1
µC
OUT
OUT
Band
pass
Demo-
dulator
VO
Input
AGC
GND
2
The external components R and C are optional
1
1
PIN
Control circuit
GND
to improve the robustnes against electrical overstress
(typical values are R = 100 Ω, C = 0.1 µF).
1
1
The output voltage VO should not be pulled down to a level
below 1 V by the external circuit.
The capacitive load at the output should be less than 2 nF.
Document Number: 81221
Rev. 1.6, 06-Nov-09
www.vishay.com
1
New TSOP582.., TSOP584..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
ABSOLUTE MAXIMUM RATINGS (1)
PARAMETER
TEST CONDITION
SYMBOL
VALUE
UNIT
V
Supply voltage (pin 3)
Supply current (pin 3)
Output voltage (pin 1)
Voltage at output to supply
Output current (pin 1)
Junction temperature
Storage temperature range
Operating temperature range
Power consumption
VS
IS
- 0.3 to + 6.0
5
- 0.3 to 5.5
- 0.3 to (VS + 0.3)
5
mA
V
VO
VS - VO
IO
V
mA
°C
Tj
100
Tstg
Tamb
Ptot
Tsd
- 25 to + 85
- 25 to + 85
10
°C
°C
Tamb ≤ 85 °C
mW
°C
Soldering temperature
t ≤ 10 s, 1 mm from case
260
Note
(1)
Stresses beyond those listed under “Absolute Maximum Ratings” may cause permanent damage to the device. This is a stress rating only
and functional operation of the device at these or any other conditions beyond those indicated in the operational sections of this specification
is not implied. Exposure to absolute maximum rating conditions for extended periods may affect the device reliability.
ELECTRICAL AND OPTICAL CHARACTERISTICS (1)
PARAMETER
TEST CONDITION
SYMBOL
MIN.
TYP.
0.85
0.95
MAX.
UNIT
mA
mA
V
Ev = 0, VS = 5 V
ISD
0.65
1.05
Supply current (pin 3)
Supply voltage
Ev = 40 klx, sunlight
ISH
VS
2.7
5.5
Ev = 0, test signal see fig. 1,
IR diode TSAL6200,
IF = 400 mA
IOSL = 0.5 mA, Ee = 0.7 mW/m2,
test signal see fig. 1
Transmission distance
Output voltage low (pin 1)
Minimum irradiance
d
40
m
VOSL
100
mV
Pulse width tolerance:
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Ee min.
0.3
45
0.45
mW/m2
tpi - 5/fo < tpo < tpi + 6/fo,
test signal see fig. 1
Maximum irradiance
Directivity
Ee max.
30
W/m2
deg
Angle of half transmission distance
ϕ1/2
Note
(1)
Tamb = 25 °C, unless otherwise specified
TYPICAL CHARACTERISTICS
Tamb = 25 °C, unless otherwise specified
1
0.9
0.8
0.7
0.6
0.5
Optical Test Signal
(IR diode TSAL6200, I = 0.4 A, 30 pulses, f = f , t = 10 ms)
E
e
Output Pulse Width
Input Burst Length
F
0
t
tpi
*
T
* tpi
10/f0 is recommended for optimal function
Output Signal
0.4
0.3
0.2
16110
VO
1)
λ = 950 nm,
7/f0 < td < 15/f0
tpi - 5/f0 < tpo < tpi + 6/f0
VOH
2)
Optical Test Signal, Fig.1
VOL
0.1
1
10
Ee - Irradiance (mW/m²)
Fig. 2 - Pulse Length and Sensitivity in Dark Ambient
102
103
104
105
2)
1)
t
t
po
td
21391
Fig. 1 - Output Active Low
www.vishay.com
2
Document Number: 81221
Rev. 1.6, 06-Nov-09
New TSOP582.., TSOP584..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
5
4.5
4
Correlation with Ambient Light Sources:
10 W/m² = 1.4 kLx (Std. illum. A, T = 2855 K)
10 W/m² = 8.2 kLx (Daylight, T = 5900 K)
Optical Test Signal
Ee
3.5
3
t
600 µs
600 µs
2.5
2
t = 60 ms
Wavelength of Ambient
Illumination: λ = 950 nm
1.5
1
94 8134
Output Signal, (see fig. 4)
VO
VOH
VOL
0.5
0
0.01
0.1
1
10
100
t
ton
toff
21393
Ee - Ambient DC Irradiance (W/m²)
Fig. 3 - Output Function
Fig. 6 - Sensitivity in Bright Ambient
f = f0
1
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
Ton
0.9
0.8
0.7
0.6
0.5
0.4
0.3
0.2
0.1
0
f = 30 kHz
f = 20 kHz
Toff
λ = 950 nm,
Optical Test Signal, Fig. 3
f = 10 kHz
f = 100 Hz
100 1000
102
103
1
10
0.1
1
10
104
105
21392
21394
ΔVsRMS - AC Voltage on DC Supply Voltage (mV)
Ee - Irradiance (mW/m²)
Fig. 4 - Output Pulse Diagram
Fig. 7 - Sensitivity vs. Supply Voltage Disturbances
1.2
1.0
0.8
0.6
0.4
0.2
500
450
400
350
300
250
200
150
100
50
f = f0 5 ꢀ
Δ f(3 dB) = f0/10
0.0
0
0
500
1000 1500 2000 2500 3000
0.7
0.9
1.1
1.3
20747
f - EMI Frequency (MHz)
16925
f/f - Relative Frequency
0
Fig. 5 - Frequency Dependence of Responsivity
Fig. 8 - Sensitivity vs. Electric Field Disturbances
Document Number: 81221
Rev. 1.6, 06-Nov-09
www.vishay.com
3
New TSOP582.., TSOP584..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
0°
10°
20°
0.8
0.7
0.6
0.5
0.4
0.3
30°
40°
TSOP582..
1.0
0.9
0.8
50°
60°
0.2
TSOP584..
70°
0.7
0.1
80°
f = 38 kHz, Ee = 2 mW/m²
0
0
20
40
60
80
100
120
0.6
0.4
0.2
0
0.2
0.4
0.6
19258
21396
drel - Relative Transmission Distance
Burst Length (number of cycles/burst)
Fig. 9 - Max. Envelope Duty Cycle vs. Burst Length
Fig. 12 - Horizontal Directivity
0°
10°
20°
0.45
0.4
30°
40°
0.35
0.3
1.0
0.9
0.8
50°
60°
0.25
0.2
70°
0.7
80°
0.15
0.6
0.4
0.2
0
0.2
0.4
0.6
- 30
- 10
10
30
50
70
90
d
- Relative Transmission Distance
19259
rel
Tamb - Ambient Temperature (°C)
21397
Fig. 10 - Sensitivity vs. Ambient Temperature
Fig. 13 - Vertical Directivity
1.2
1.0
0.8
0.6
0.4
0.2
0
0.5
0.45
0.4
0.35
0.3
0.25
0.2
750
850
950
1050
1150
1.5
2
2.5
3
3.5
4
4.5
5
5.5
21398
VS - Supply Voltage (V)
94 8408
- Wavelength (nm)
Fig. 11 - Relative Spectral Sensitivity vs. Wavelength
Fig. 14 - Sensitivity vs. Supply Voltage
www.vishay.com
4
Document Number: 81221
Rev. 1.6, 06-Nov-09
New TSOP582.., TSOP584..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
SUITABLE DATA FORMAT
The TSOP582.., TSOP584.. series are designed to suppress
spurious output pulses due to noise or disturbance signals.
Data and disturbance signals can be distinguished by the
devices according to carrier frequency, burst length and
envelope duty cycle. The data signal should be close to the
band-pass center frequency (e.g. 38 kHz) and fulfill the
conditions in the table below.
When a data signal is applied to the TSOP582.., TSOP584..
in the presence of a disturbance signal, the sensitivity of the
receiver is reduced to insure that no spurious pulses are
present at the output. Some examples of disturbance signals
which are suppressed are:
IR Signal from Fluorescent
Lamp with Low Modulation
5
0
10
15
20
16920
Time (ms)
• DC light (e.g. from tungsten bulb or sunlight)
• Continuous signals at any frequency
Fig. 15 - IR Signal from Fluorescent Lamp
with Low Modulation
• Strongly or weakly modulated noise from fluorescent
lamps with electronic ballasts (see figure 15 or figure 16)
IR Signal from Fluorescent
Lamp with High Modulation
0
5
10
15
20
16921
Time (ms)
Fig. 16 - IR Signal from Fluorescent Lamp
with High Modulation
TSOP582..
TSOP584..
Minimum burst length
10 cycles/burst
10 cycles/burst
After each burst of length
a minimum gap time is required of
10 to 70 cycles
≥ 12 cycles
10 to 35 cycles
≥ 12 cycles
For bursts greater than
a minimum gap time in the data stream is needed of
70 cycles
> 4 x burst length
35 cycles
> 10 x burst length
Maximum number of continuous short bursts/second
Recommended for NEC code
800
yes
yes
yes
yes
yes
yes
1300
yes
yes
no
Recommended for RC5/RC6 code
Recommended for Sony code
Recommended for Thomson 56 kHz code
Recommended for Mitsubishi code (38 kHz, preburst 8 ms, 16 bit)
Recommended for Sharp code
yes
yes
yes
Most common disturbance
signals are suppressed
Even extreme disturbance
signals are suppressed
Suppression of interference from fluorescent lamps
Note
For data formats with short bursts please see the datasheet of TSOP581.., TSOP583.. .
Document Number: 81221
Rev. 1.6, 06-Nov-09
www.vishay.com
5
New TSOP582.., TSOP584..
IR Receiver Modules for Remote
Vishay Semiconductors
Control Systems
PACKAGE DIMENSIONS in millimeters
5
4.8
(4)
2.8
R 2
(1.54)
0.85 max.
OUT
GND
VCC
0.5 max.
2.54 nom.
0.7 max.
0.2
1.2
2.54 nom.
Marking area
technical drawings
according to DIN
specifications
Not indicated tolerances 0.2
Drawing-No.: 6.550-5263.01-4
Issue: 11; 17.12.08
19009
R2
www.vishay.com
6
Document Number: 81221
Rev. 1.6, 06-Nov-09
Legal Disclaimer Notice
Vishay
Disclaimer
All product specifications and data are subject to change without notice.
Vishay Intertechnology, Inc., its affiliates, agents, and employees, and all persons acting on its or their behalf
(collectively, “Vishay”), disclaim any and all liability for any errors, inaccuracies or incompleteness contained herein
or in any other disclosure relating to any product.
Vishay disclaims any and all liability arising out of the use or application of any product described herein or of any
information provided herein to the maximum extent permitted by law. The product specifications do not expand or
otherwise modify Vishay’s terms and conditions of purchase, including but not limited to the warranty expressed
therein, which apply to these products.
No license, express or implied, by estoppel or otherwise, to any intellectual property rights is granted by this
document or by any conduct of Vishay.
The products shown herein are not designed for use in medical, life-saving, or life-sustaining applications unless
otherwise expressly indicated. Customers using or selling Vishay products not expressly indicated for use in such
applications do so entirely at their own risk and agree to fully indemnify Vishay for any damages arising or resulting
from such use or sale. Please contact authorized Vishay personnel to obtain written terms and conditions regarding
products designed for such applications.
Product names and markings noted herein may be trademarks of their respective owners.
Document Number: 91000
Revision: 18-Jul-08
www.vishay.com
1
相关型号：
©2020 ICPDF网 联系我们和版权申明