RFLPF1005040A27B1U [WALSIN]

2.4 GHz ISM Band RF Application;
RFLPF1005040A27B1U
型号: RFLPF1005040A27B1U
厂家: Walsin Technology    Walsin Technology
描述:

2.4 GHz ISM Band RF Application

ISM频段
文件: 总7页 (文件大小:539K)
中文:  中文翻译
下载:  下载PDF数据表文档文件
Approval sheet  
MULTILAYER CERAMIC LOW PASS FILTER  
RFLPF Series 1005(0402)- RoHS Compliance  
Halogens Free Product  
2.4 GHz ISM Band RF Application  
P/N: RFLPF1005040A27B1U  
*Contents in this sheet are subject to change without prior notice.  
Page 1 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
FEATURES  
1.  
2.  
3.  
4.  
5.  
Miniature footprint: 1.0 X 0.5 X 0.4 mm3  
Low Profile Thickness  
High Rejection Rate  
High Attenuation on harmonic Suppressed  
LTCC process  
APPLICATIONS  
1.  
2.  
ISM band 2.4GHz working frequency  
Bluetooth, Wireless LAN 802.11b/g/n, HomeRF  
CONSTRUCTION  
P4  
PIN  
1
Connection  
Input port  
GND  
2
P3  
P1  
3
Output port  
GND  
4
P2  
DIMENSIONS  
Figure  
Symbol  
Dimension (mm)  
L
W
T
1.00 ± 0.10  
0.50 ± 0.10  
0.40 ± 0.10  
0.35 ± 0.10  
0.30 ± 0.10  
0.15 ± 0.10  
0.15 ± 0.10  
Bottom view  
Top view  
A
B
C
D
Side view  
Side view  
E
0.30 ± 0.10  
Page 2 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
ELECTRICAL CHARACTERISTICS  
RFLPF1005040A27B1U  
Frequency range  
Specification  
2400 ~ 2500 MHz  
0.75 dB max at +25°C  
Insertion Loss  
Attenuation  
0.90 dB max at -40°C ~ +85°C  
32 dB min. @ 4800~ 5000MHz  
35 dB min. @ 7200~ 7500MHz  
1.9 max.  
VSWR  
50 Ω  
Impedance  
Power Capacity  
2W max.  
Moisture sensitivity levels  
MSL is LEVEL 1 (Refer to : IPC/JEDEC J-STD-020)  
Operating & Storage Condition (Component)  
Operation Temperature Range: -40 ~ +85  
Storage Temperature Range: -40 ~ +85 ℃  
Storage Condition before Soldering (Included packaging material)  
Storage Temperature Range: +5 ~ +40 ℃  
Humidity: 30 to 70% relative humidity  
Typical Electrical Chart  
SOLDER LAND PATTERN  
Figure  
Unit : mm  
Line width to be designed to match 50 Ω characteristic impedance, depending on PCB material and thickness.  
Page 3 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
RELIABILITY TEST  
Test condition / Test method  
Test item  
Specification  
Solderability  
At least 95% of a surface of each terminal  
*Solder bath temperature235 5C  
JIS C 0050-4.6  
JESD22-B102D  
electrode must be covered by fresh solder.  
*Immersion time2 0.5 sec  
SolderSn3Ag0.5Cu for lead-free  
*Solder bath temperature260 5C  
*Leaching immersion time30 0.5 sec  
Solder : SN63A  
Leaching  
Loss of metallization on the edges of each  
electrode shall not exceed 25%.  
(Resistance to  
dissolution of  
metallization)  
IEC 60068-2-58  
Resistance to soldering  
heat  
*Preheating temperature120~150,  
1 minute.  
No mechanical damage.  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
JIS C 0050-5.4  
*Solder temperature2705C  
*Immersion time101 sec  
SolderSn3Ag0.5Cu for lead-free  
Loss of metallization on the edges of each  
electrode shall not exceed 25%.  
Measurement to be made after keeping at  
room temperature for 242 hrs  
Drop Test  
*Height75 cm  
No mechanical damage.  
JIS C 0044  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
*Test SurfaceRigid surface of concrete or  
Customer’s specification.  
steel.  
*Times6 surfaces for each units2 times  
for each side.  
Vibration  
*Frequency10Hz~55Hz~10Hz(1min)  
*Total amplitude1.5mm  
No mechanical damage.  
JIS C 0040  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
*Test times6hrs.(Two hrs each in three  
mutually perpendicular directions)  
Adhesive Strength  
of Termination  
*Pressurizing force  
No remarkable damage or removal of the  
termination.  
5N(0603)10N(>0603)  
JIS C 0051- 7.4.3  
*Test time10±1 sec  
Bending test  
The middle part of substrate shall be  
pressurized by means of the pressurizing rod  
at a rate of about 1 mm/s per second until the  
deflection becomes 1mm/s and then pressure  
shall be maintained for 51 sec.  
No mechanical damage.  
JIS C 0051- 7.4.1  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
Measurement to be made after keeping at  
room temperature for 242 hours  
Page 4 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
Temperature cycle  
JIS C 0025  
1. 303 minutes at -40C3C,  
2. 10~15 minutes at room temperature,  
3. 303 minutes at +85C3C,  
No mechanical damage.  
Electrical specification shall satisfy the  
descriptions in electrical characteristics  
under the operational temperature range  
within -40 ~ 85°C.  
4. 10~15 minutes at room temperature,  
Total 100 continuous cycles  
Measurement to be made after keeping at  
room temperature for 242 hrs  
High temperature  
JIS C 0021  
*Temperature85C2C  
No mechanical damage.  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
*Test duration1000+24/-0 hours  
Measurement to be made after keeping at  
room temperature for 242 hrs  
Humidity  
*Humidity90% to 95% R.H.  
*Temperature402C  
*Time1000+24/-0 hrs.  
No mechanical damage.  
(steady conditions)  
JIS C 0022  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
Measurement to be made after keeping at  
room temperature for 242 hrs  
500hrs measuring the first data then  
1000hrs data  
Low temperature  
JIS C 0020  
*Temperature-40C2C  
No mechanical damage.  
Electrical specification shall satisfy the  
descriptions in electrical characteristics under  
the operational temperature range within -40  
~ 85°C.  
*Test duration1000+24/-0 hours  
Measurement to be made after keeping at  
room temperature for 242 hrs  
Page 5 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
SOLDERING CONDITION  
Typical examples of soldering processes that provide reliable joints without any damage are given in Fig 2,  
Fig 2. Infrared soldering profile  
ORDERING CODE  
RF  
Walsin  
LPF  
Product Code  
LPF :  
100504  
0
A
27B1U  
Specification  
Design code  
Dimension code  
Unit of  
dimension  
Application  
RF device  
Per 2 digits of Length,  
Width, Thickness :  
A : 2.4GHz ISM  
Band  
0 : 0.1 mm  
1 : 1.0 mm  
Low Pass Filter  
e.g. :  
100504 =  
Length 10,  
Width 05,  
Thickness 04  
Minimum Ordering Quantity: 4000 pcs per reel.  
PACKAGING  
Paper Tape specifications (unit :mm)  
Index  
Ao  
Bo  
T
W
D  
Dimension (mm)  
Index  
1.50 + 0.10  
0.67 0.10  
E
1.14 0.10  
F
0.42 0.10  
8.0 0.30  
P2  
Po  
P1  
Dimension (mm)  
1.75 0.10  
3.50 0.20  
4.00 0.10  
2.00 0.10  
2.00 0.10  
Page 6 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  
Approval sheet  
Reel dimensions  
B
A
C
Index  
A
B
C
Φ178.0  
Φ60.0  
Φ13.0  
Dimension (mm)  
Taping Quantity: 4000 pieces per 7” reel  
CAUTION OF HANDLING  
Limitation of Applications  
Please contact us before using our products for the applications listed below which require especially high reliability for  
the prevention of defects, which might directly cause damage to the third party’s life, body or property.  
(1) Aircraft equipment  
(2) Aerospace equipment  
(3) Undersea equipment  
(4) Medical equipment  
(5) Disaster prevention / crime prevention equipment  
(6) Traffic signal equipment  
(7) Transportation equipment (vehicles, trains, ships, etc.)  
(8) Applications of similar complexity and /or reliability requirements to the applications listed in the above.  
Storage condition  
(1) Products should be used in 6 months from the day of WALSIN outgoing inspection.  
(2) Storage environment condition.  
Products should be storage in the warehouse on the following conditions.  
Temperature  
Humidity  
: +5 to +40℃  
: 30 to 70% relative humidity  
Don’t keep products in corrosive gases such as sulfur. Chlorine gas or acid or it may cause oxidization of  
electrode, resulting in poor solderability.  
Products should be storage on the palette for the prevention of the influence from humidity, dust and son on.  
Products should be storage in the warehouse without heat shock, vibration, direct sunlight and so on.  
Products should be storage under the airtight packaged condition.  
Page 7 of 7  
ASC_RFLPF1005040A27B1U_V02  
May 2017  

相关型号:

RFLPF1005040A5T

2.4 GHz ISM Band Working Frequency
WALSIN

RFLPF1005041A1T

2.4 GHz ISM Band Working Frequency
WALSIN

RFLPF1005041A27B1U

2.4 GHz ISM Band RF Application
WALSIN

RFLPF1005041A5T

2.4 GHz ISM Band Working Frequency
WALSIN

RFLPF10050G9D0T

850/900 MHz GSM Band RF Application
WALSIN

RFLPF10050G9D2T

For GSM850/ 900 Band Application
WALSIN

RFLPF10050G9D3T

850/900 MHz GSM Band Working Frequency
WALSIN

RFLPF10050G9D48Q1C

850/900 MHz GSM Band Working Frequency
WALSIN

RFLPF10050G9D4T

850/900 MHz GSM Band Working Frequency
WALSIN

RFLPF10050G9D58Q1C

850/900 MHz GSM Band RF Application
WALSIN

RFLPF10050G9DM1T76

GSM & LTE Band RF Application
WALSIN

RFLPF10051G8D0T

1.8 GHz DCS/ PCS Band Working Frequency
WALSIN