HSHM-H176DG4-8CP2-TG50 [3M]
TWO PART BOARD CONNECTOR;型号: | HSHM-H176DG4-8CP2-TG50 |
厂家: | 3M ELECTRONICS |
描述: | TWO PART BOARD CONNECTOR 连接器 |
文件: | 总4页 (文件大小:1073K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DG,176 Signal Contacts, 8 Rows, Straight
HSHM Series
•ꢀ Upꢀtoꢀ5ꢀGb/sꢀdataꢀrates
•ꢀ Lowꢀcrosstalkꢀatꢀhighꢀfrequencies
•ꢀ 50/100ꢀΩꢀ(single-endedꢀ/differential)ꢀimpedance
•ꢀ Modular/scalableꢀformatꢀIECꢀ61076-4-101
•ꢀ 101ꢀmatedꢀlinesꢀperꢀlinearꢀinch
•ꢀ Integratedꢀguideꢀpin
•ꢀ End-to-endꢀstackableꢀwithꢀ8ꢀrowꢀ3M™ꢀMetPak™ꢀCP2,ꢀ
HMꢀandꢀHSHMꢀheaders
•ꢀ MatesꢀwithꢀHSHMꢀDꢀsockets
•ꢀ SeeꢀtheꢀRegulatoryꢀInformationꢀAppendixꢀ(RIA)ꢀinꢀ
theꢀ“RoHSꢀcompliance”ꢀsectionꢀofꢀ
www.3mconnector.comꢀforꢀcomplianceꢀinformation
Date Modified: November 5, 2010
TS-2079-B
Sheet 1 of 3
Physical
Insulation:
Material: High Temperature Thermoplastic (LCP)
Flammability: UL 94V-0
Contact:
Material:
CopperAlloy
Plating: See Ordering Information
Performance
Mechanical:
Normal Force (Nominal): 0.57 N [58 g] Signal, 0.74 N [75 g] Shield
Engagement Force (Nominal): 0.32 N [33 g] Signal, 0.22 N [22 g] Shield
Separation Force (Nominal): 0.20 N [20 g] Signal, 0.20 N [20 g] Shield
Wipe (Nominal, Shortest Contact): 2.67 mm [0.105 in] Signal, 1.57 mm [0.062 in] Shield
Mate/Unmate Cycles: 250
Application: This module is not suitable for stand-alone use. (Refer to IEC-61076-4-101)
Electrical:
Data Rate: 5 Gb/s
Characteristic Impedance:
50 Ω Single-ended, 100 Ω Differential
Current Rating (Fully Loaded): 1A @ 70° C Signal
Insulation Resistance:
104 MΩ @ 100VDC
WithstandingVoltage: 750Vrms
Environmental
-55° C to 125° C
Temperature Rating:
ULꢀFileꢀNo.:ꢀE68080ꢀ
MetPakꢀisꢀaꢀtrademarkꢀofꢀ3MꢀCompany.
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DG,176 Signal Contacts, 8 Rows, Straight
HSHM Series
49.85
2.00
.079
1.963
2.00
.079
Pin positions
2.00
.079
2.00
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24 25
.079
ROW I
ROW H
ROW G
ROW F
ROW E
ROW D
ROW C
18.00
.709
ROW B
ROW A
ROW Z
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
Shield positions
21.40
.843
48.00
1.890
15.60
.614
denotes shield column (tail only) omitted for the
row differential pair part
Interstitial
ground
contacts
5.00
.197
1.50
.059
Signal
contacts
23.84
.938
HSHM-HXXXXX-8XPX-XXXXX
REV X XXYY
13.40
.528
DIM A
4.50
.177
DIM B
Coaxial, column differential and stripline configuration
shown with protective caps*
DIM C
DIM A = Pin mating length
DIM B = Shield tail length
DIM C = Pin tail length
HSHM-HXXXXX-8XPX-XXXXX
REV X
XXYY
mm
(Inch)
Tolerance Unless Noted
Row differential configuration
shown with protective caps*
0
0.0
0.3
0.00
0.13
mm
3
( ) Dimensions used for
Reference Only
* Caps to be removed after press-fit installation process
Ordering Information
(rows I and Z not loaded)
HSHM-H176DGX-8CPX- XXXXX
Plating μm [ μ” ]:
High Speed Option:
TG30 = 0.76 [30] Min.Au Contact Area
4 = Coaxial, column differential and
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
stripline (75 Ω) applications
Standard Option
5 = Row differential applications
TG30L = 0.76 [30] Min.Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Tail Length:
Typically higher make order quantities as compared to TG30.
1 = 4.4 mm pin and 3.5 mm shield
2 = 2 mm pin and 2 mm shield
TG50 =1.27 [50] Min.Au Contact Area, Lubricated
2.54 [100] Min. SnPb Terminal Area (RIA C2 & E2 apply)
1.27 [50] Min. Ni All over
Non-Standard Option (Available with longer lead times and
higher make order quantities, MOQ)
Standard Configuration
DIM A = 5.3 mm for rows A through H
For non--standard configurations contact sales representative
TS-2079-B
Sheet 2 of 3
3M is a trademark of 3M Company.
For technical, sales or ordering information call
800-225-5373
3
Electronic Solutions Division
Interconnect Solutions
http://www.3Mconnector.com
3M™ MetPak™ HSHM Press-Fit Header
2 mm Type DG,176 Signal Contacts, 8 Rows, Straight
HSHM Series
2.00
1.00
1.00
2.00
25
24
23
22
21
25
24
23
22
21
20
19
18
17
16
15
14
13
12
11
10
9
20
+0.05
Ø
2.00
0
19
18
17
16
15
14
13
12
11
10
9
0.10 A
B
Ø
4.00
4.00
Ø
DIM. D
8
8
M
A B
Ø
0.10
48.00
7
7
Plated thru holes
See hole plating table
6
6
5
5
4
4
3
3
2
2
1
1
A
H
G F
E D C B A
H
G F
E D C B A
6.00
B
Recommended PCB hole mounting pattern for row
differential applications
Recommended PCB hole mounting pattern for coaxial,
column differential and stripline applications
(Same geometry as left view without the ground vias)
Hole Plating Table mm
Finished Hole Dia. “D”
Cu.Thickness
0.025 - 0.045 [.0010 - .0018]
SnPb Thickness
Drilled Hole Dia.
0.457 - 0.559 [.0180 - .0220]
0.008 -0.018 [.0003 - .0007]
0.584 - 0.625 [.0230 - .0246]
TS-2079-B
Sheet 3 of 3
3M is a trademark of 3M Company.
3
For technical, sales or ordering information call
Electronic Solutions Division
Interconnect Solutions
800-225-5373
http://www.3Mconnector.com
Important Notice
All statements, technical information, and recommendations related to 3M’s products are based on information believed to be reliable, but the accuracy or completeness
is not guaranteed. Before using this product, you must evaluate it and determine if it is suitable for your intended application. You assume all risks and liability associated
with such use. Any statements related to the product which are not contained in 3M’s current publications, or any contrary statements contained on your purchase order
shall have no force or effect unless expressly agreed upon, in writing, by an authorized officer of 3M.
Warranty; Limited Remedy; Limited Liability.
This product will be free from defects in material and manufacture for a period of one (1) year from the time of purchase. 3M MAKES NO OTHER WARRANTIES
INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. If this product is defective within the
warranty period stated above, your exclusive remedy shall be, at 3M’s option, to replace or repair the 3M product or refund the purchase price of the 3M product. Except
where prohibited by law, 3M will not be liable for any indirect, special, incidental or consequential loss or damage arising from this 3M product, regardless of
the legal theory asserted.
3M Electronics Solutions Division
6801 River Place Blvd.
Austin, TX 78726-9000
U.S.A.
1-800-225-5373
www.3Mconnector.com
Please recycle. Printed in USA.
© 3M 2010. All rights reserved.
RIA-2217B-E
3M is a trademark of 3M Company.
相关型号:
©2020 ICPDF网 联系我们和版权申明