AD8387 [ADI]
High Performance, 12-Bit, 12-Channel Decimating, LCD DecDriver; 高性能， 12位， 12通道抽选，液晶DecDriver
| 型号： | AD8387 |
| 厂家： | 
ADI |
| 描述： | High Performance, 12-Bit, 12-Channel Decimating, LCD DecDriver |
| 文件： | 总16页 (文件大小：398K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
High Performance, 12-Bit, 12-Channel
Decimating, LCD DecDriver®
AD8387
FUNCTIONAL BLOCK DIAGRAM
FEATURES
High accuracy, high-resolution voltage outputs
1 mV channel matching
12-bit input resolution
12
12
12
TWO-STAGE
LATCH
DAC
DAC
VID0
VID1
DBA(0:11)
DBB(0:11)
12
12
12
TWO-STAGE
LATCH
Laser-trimmed outputs
Fast settling, high voltage drive
35 ns settling time to 0.25% into 150 pF load
Slew rate 420 V/μs
Outputs to within 1.3 V of supply rails
High update rates
BIAS
BYP
TSW
THERMAL
SWITCH
12
12
12
TWO-STAGE
LATCH
DAC
DAC
VID10
VID11
G-MODE
SWITCH
GSW
DSW
Fast, 110 MHz clock
12
TWO-STAGE
LATCH
Programmable video reference (brightness) and
full-scale (contrast) output levels
Flexible logic
INV bit reverses polarity of video signal
R/L reverses loading order of data
ISW selects frame/row or column/dot inversion
DSW selects single or dual data bus mode
Output short-circuit protection
3.3 V logic, 11 V to 18 V analog supplies
Available in 80-lead, 12 mm × 12 mm, TQFP E-pad
CLK
XFR
R/L
SEQUENCE
CONTROL
SCALING
CONTROL
AD8387
INV ISW
VRH VRL
Figure 1.
APPLICATIONS
LCD microdisplay driver
GENERAL DESCRIPTION
5
4
3
2
1
0
The AD8387 DecDriver provides dual, fast latched, 12-bit
decimating input, which drives 12 high voltage outputs. Twelve-
bit input words are loaded into 12 separate high speed, bipolar
DACs sequentially. Flexible digital input format allows more
than one AD8387 to be used in parallel for higher resolution
displays. The output signal can be adjusted for dc reference,
signal inversion, and contrast for maximum flexibility.
NORMAL PROJECTOR OPERATING
TEMPERATURE RANGE
CODE 0
CODE 2048
The AD8387 is fabricated on ADI’s fast bipolar, 26 V XFCB
process, providing fast input logic, bipolar DACs with trimmed
accuracy and fast settling, high voltage, precision drive
amplifiers on the same chip.
CODE 4095
0
10
20
30
40
50
60
70
80
The AD8387 dissipates 1.34 W nominal static power. The
AD8387 is offered in an 80-lead TQFP E-pad package and
operates over the commercial temperature range of 0°C to
+85°C.
INTERNAL AMBIENT TEMPERATURE (°C)
Figure 2. Channel Matching vs. Temperature
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rights of third parties that may result from its use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks and registeredtrademarks arethe property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2005 Analog Devices, Inc. All rights reserved.
AD8387
TABLE OF CONTENTS
Features .............................................................................................. 1
Theory of Operation ...................................................................... 13
Transfer Function and Analog Output Voltage...................... 13
Accuracy ...................................................................................... 13
Applications..................................................................................... 14
Optimized Reliability with the Thermal Switch .................... 14
Initial Power-Up After Assembly or Repair............................ 14
Power-Up During Normal Operation..................................... 14
Power Supply Sequencing ......................................................... 14
Power-On Sequence................................................................... 14
Power-Off Sequence................................................................... 14
Grounded Output Mode During Power-Off .......................... 14
PCB Design for Optimized Thermal Performance ............... 14
Thermal Pad Design .................................................................. 15
Thermal via Structure Design .................................................. 15
AD8387 PCB Design Recommendations ............................... 15
Outline Dimensions....................................................................... 16
Ordering Guide .......................................................................... 16
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Absolute Maximum Ratings............................................................ 5
Exposed Paddle............................................................................. 5
Overload Protection..................................................................... 5
Maximum Power Dissipation ..................................................... 5
Operating Temperature Range ................................................... 5
ESD Caution.................................................................................. 5
Pin Configuration and Function Descriptions............................. 6
Typical Performance Characteristics ............................................. 8
Timing Diagrams.............................................................................. 9
Single Data Bus Configuration, DSW = LOW......................... 9
Dual Data Bus Configuration, DSW = HIGH........................ 10
Functional Description.................................................................. 12
Reference and Control Input Description............................... 12
REVISION HISTORY
10/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 16
AD8387
SPECIFICATIONS
TA = 25°C, AVCC = 15.5 V, DVCC = 3.3 V, VRH = 9.5 V, VRL = 7 V, TA MIN = 0°C, TA MAX = 75°C still air, unless otherwise noted.
Table 1.
Parameter
VIDEO DC PERFORMANCE1
Conditions
Min
Typ
Max
Unit
TA MIN to TA MAX ,VFS = 5 V
VDE—Differential Error Voltage
VCME—Common-Mode Error Voltage
ΔVDE—VDE Channel Matching
ΔV—Channel Matching
@ DAC code 0
−5.5
−4.4
−3.6
−2.8
−2.1
−6.0
−0.8
−0.5
−0.3
−0.3
+0.2
+5.0
+3.6
+3.3
+2.8
+2.1
+6.0
mV
mV
mV
mV
mV
mV
@ DAC code 1024
@ DAC code 2048
@ DAC code 3072
@ DAC code 4095
DAC code range 0 to 4095
@ DAC code 0
−2.5
−2.5
−2.5
−2.5
−2.5
−3.5
−0.3
−0.3
−0.3
−0.3
−0.3
+2.5
+2.5
+2.5
+2.5
+2.5
+3.5
mV
mV
mV
mV
mV
mV
@ DAC code 1024
@ DAC code 2048
@ DAC code 3072
@ DAC code 4095
DAC code range 0 to 4095
@ DAC code 0
1.9
1.8
1.6
1.4
1.0
4.8
4.3
4.0
3.8
2.8
5.5
mV
mV
mV
mV
mV
mV
@ DAC code 1024
@ DAC code 2048
@ DAC code 3072
@ DAC code 4095
DAC code range 0 to 4095
@ DAC code 0
2.7
2.7
2.5
2.5
2.0
mV
mV
mV
mV
mV
mV
@ DAC code 1024
@ DAC code 2048
@ DAC code 3072
@ DAC code 4095
DAC code range 0 to 4095
7.5
DNL2
−1
−0.2
LSB
VIDEO OUTPUT DYNAMIC PERFORMANCE
Data Switching Settling Time to 0.25%
Data Switching Settling Time to 1%
Data Switching Slew Rate
CLK and Data Feedthrough3
All-Hostile Crosstalk4
TA MIN to TA MAX
VIDx = 5 V step, CL = 150 pF
35
22
420
15
50
28
ns
ns
V/μs
mV p-p
20% to 80%
Amplitude
Glitch Duration
DAC Transition Glitch Energy
69
50
0.4
mV p-p
ns
nV-s
DAC Code 2047 to 2048
VIDx = 10 V step, CL = 150 pF
20% to 80%
Invert Switching Settling Time to 0.25%
Invert Switching Settling Time to 1%
Invert Switching Slew Rate
70
34
700
25
150
40
ns
ns
V/μs
mV
Invert Switching Overshoot
Rev. 0 | Page 3 of 16
AD8387
Parameter
Conditions
Min
Typ
Max
Unit
VIDEO OUTPUT CHARACTERISTICS
Output Voltage Swing
AVCC − VOH, VOL − AGND
VIDx = 5 V step
0.9
0.06
15.7
1.3
0.150
V
V
Output Voltage—Grounded Mode
5
Data Switching Delay: t7
ns
ns
ns
ns
mA
Ω
5
Data Switching Delay Skew: Δt7
4
4
6
INV Switching Delay: t8
VIDx = 10 V step
16.2
6
INV Switching Delay Skew: Δt8
Output Current
Output Resistance
REFERENCE INPUTS
VRL Range
100
28
VRH ≥ VRL
VRH ≥ VRL
5.25
VRL
0
AVCC − 4
VRL + 2.75
2.75
V
V
V
kΩ
μA
μA
Bits
VRH Range
VRH to VRL Range1
VRH Input Resistance
VRL Input Current
VRH Input Current
RESOLUTION
To VRL
22
−44
111
Binary Coding
12
DIGITAL INPUT CHARACTERISTICS
TA MIN to TA MAX
CLK input duty cycle 40% to 60%
CLK Frequency
DSW = HIGH
DSW = LOW
110
85
MHz
MHz
ns
ns
ns
ns
ns
ns
ns
Data Setup Time: t1
XFR Setup Time: t3
Data Hold Time: t2
XFR Hold Time: t4
CLK High Time: t5
CLK Low Time: t6
CLK High Time: t7
CLK Low Time: t8
CIN
IIH
IIH TSW
IIH XFR
IIL
0
0
3.5
3.5
2.5
3.0
3.5
4.0
DSW = HIGH
DSW = HIGH
DSW = LOW
DSW = LOW
ns
3
pF
μA
μA
μA
μA
μA
μA
V
0.05
333
0.05
−0.6
−1.3
−1.2
IIL TSW
IIL XFR
VIH
2
VIL
0.8
V
VTH
1.65
V
POWER SUPPLIES
DVCC, Operating Range
DVCC, Quiescent Current
AVCC, Operating Range
AVCC, Quiescent Current
OPERATING TEMPERATURE
3
3.3
54
3.6
70
18
V
mA
V
11
75
100
mA
7
Ambient Temperature Range, TA
Ambient Temperature Range, TA
Still air, TSW = LOW
200 lfm airflow, TSW = LOW
0
0
75
85
°C
°C
7
1 VDE = differential error voltage, VCME = common-mode error voltage, ΔVDE = VDE matching between outputs, ΔV = maximum deviation between outputs, and full-scale output
voltage = VFS = 2 × (VRH − VRL). See the Accuracy section.
2 Guaranteed monotonic by characterization to four sigma limits.
3 Measured on two outputs differentially as CLK and DBx(0:11) are driven and XFR is held LOW.
4 Measured on two outputs differentially as the others are transitioning by 5 V. Measured for both states of INV.
5 Measured from 50% of rising CLK edge to 50% of output change. Measurement is made for both states of INV.
6 Measured from 50% of INV transition to 50% of output change.
7 Operation at elevated ambient temperature requires a thermally optimized PCB and additional thermal management, such as airflow across the surface of the AD8387.
Rev. 0 | Page 4 of 16
AD8387
ABSOLUTE MAXIMUM RATINGS
Table 2.
Parameter
When TSW is HIGH, the output current limiter, as well as the
thermal switch, is enabled. The thermal switch debiases the
output amplifier when the junction temperature reaches the
internally set trip point. In the event of an extended short-
circuit between a video output and a power supply rail, the
output amplifier current continues to switch between 0 and
100 mA typical with a period determined by the thermal time
constant and the hysteresis of the thermal trip point. The
thermal switch, when enabled, provides long-term protection
from accidental shorts during the assembly process by limiting
the average junction temperature to a safe level.
Rating
Supply Voltages
AVCCx − AGNDx
DVCC − DGND
Input Voltages
Maximum Digital Input Voltage
Minimum Digital Input Voltage
Maximum Analog Input Voltage
Minimum Analog Input Voltage
Internal Power Dissipation1
TQFP E-Pad @ TA = 25°C
Operating Temperature Range
Storage Temperature Range
Lead Temperature Range (Soldering 10 sec)
18 V
4.5 V
DVCC + 0.5 V
DGND − 0.5 V
AVCC + 0.5 V
AGND − 0.5 V
4.38 W
MAXIMUM POWER DISSIPATION
0°C to 85°C
−65°C to +125°C
300°C
The maximum power that the AD8387 can safely dissipate is
limited by its junction temperature. The maximum safe junction
temperature for plastic encapsulated devices, as determined by the
glass transition temperature of the plastic, is approximately 150°C.
Exceeding this limit temporarily can cause a shift in the parametric
performance due to a change in the stresses exerted on the die by
the package. Exceeding a junction temperature of 150°C for an
extended period can result in device failure.
1 80-lead TQFP E-Pad:
θJA = 28.5°C/W (still air) [JEDEC Standard, 4-layer PCB in still air]
θJC = 12.2°C/W
θ
JB = 14.6°C/W
ΨJB = 12.0°C/W
ΨJT = 0.3°C/W.
Stresses above those listed under the Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only; functional operation of the device at these or
any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to the
absolute maximum ratings for extended periods may reduce
device reliability.
OPERATING TEMPERATURE RANGE
To ensure operation within the specified operating temperature
range, it is necessary to limit the maximum power dissipation as
follows.
3.0
EXPOSED PADDLE
500LFM
200LFM
2.5
To ensure optimized thermal performance, the exposed paddle
must be thermally connected to an external plane, such as
AVCC or GND, as described in the Applications section.
STILL AIR
2.0
OVERLOAD PROTECTION
The AD8387 overload protection circuit consists of an output
current limiter and a thermal switch.
1.5
QUIESCENT
When TSW is LOW, the thermal switch is disabled and the
output current limiter is enabled. The maximum current at any
one output is internally limited to 100 mA average. In the event
of a momentary short-circuit between a video output and a
power supply rail (VCC or AGND), the output current limit is
sufficiently low to provide temporary protection.
THERMAL
SWITCH
1.0
50
75
ENABLED
55
80
60
85
65
90
70
95
75
80
85
90
95
100
DISABLED
100 105 110 115 120 125
AMBIENT TEMPERATURE (°C)
Figure 3. Maximum Power Dissipation vs. Temperature,
AD8387 on a 4-Layer JEDEC PCB with Thermally Optimized Landing
Pattern as Described in the Applications Section
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance
degradation or loss of functionality.
Rev. 0 | Page 5 of 16
AD8387
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
80 79 78 77 76 75 74 73 72 71 70 69 68 67 66 65 64 63 62 61
1
60
59
58
57
56
55
54
53
52
51
50
49
48
47
46
45
44
43
42
41
DBA5
DBA6
DBA7
DBA8
DBA9
DBA10
DBA11
XFR
VID1
PIN 1
2
AGND1, 2
VID2
3
4
AVCC2, 3
VID3
5
6
AGND3, 4
VID4
7
AD8387
8
AVCC4, 5
VID5
TOP VIEW
(Not to Scale)
9
DVCC1
DGND1
CLK
10
11
12
13
14
15
16
17
18
19
20
AGND5, 6
VID6
DSW
AVCC6, 7
VID7
R/L
DBB11
DBB10
DBB9
DBB8
DBB7
DBB6
DBB5
AGND7, 8
VID8
AVCC8, 9
VID9
AGND9, 10
VID10
AVCC10, 11
21 22 23 24 25 26 27 28 29 30 31 32 33 34 35 36 37 38 39 40
NC = NO CONNECT
Figure 4. 80-Lead TQFP E-Pad Pin Configuration
Rev. 0 | Page 6 of 16
AD8387
Table 3. 80-Lead TQFP E-Pad Pin Configurations
Pin No.
Mnemonic
Function
Description
1 to 7,
DBA(0:11)
Data Input
12-Bit Data Input for Even Channels. VID(0, 2, 4, 6, 8, 10), MSB = DBA11.
76 to 80;
14 to 25
8
DBB(0:11)
XFR
Data Input
12-Bit Data Input for Odd Channels. VID(1, 3, 5, 7, 9, 11), MSB = DBB11.
Transfer/Start Sequence
Simultaneously initiates a new data loading sequence and transfers data
loaded previously, to the outputs.
9, 26, 75
10, 27, 74
DVCCx
DGNDx
CLK
DSW
R/L
ISW
INV
GSW
TSW
AGNDx
Digital Power Supplies
Digital Ground
Clock
Data Mode Switch
Right/Left Select
Invert Mode Switch
Invert
Output Mode Switch
Thermal Switch
Analog Ground
Digital Power Supplies.
These pins are normally connected to the digital ground plane.
Clock Input.
Selects Single Buss or Dual Buss Operating Modes.
Selects Left Direction or Right Direction Operating Mode.
Enables and Disables Column Inversion.
Changes the Polarity of the Analog Output Signals.
Enables and Disables Grounded Mode.
Enables and Disables Long-Term Output Protection.
Analog Supply Returns.
11
12
13
28
29
30
31
32, 33, 39, 43,
47, 51, 55, 59,
63, 69, 70
34, 35, 41,
45, 49, 53,
57, 61, 67, 68
36
AVCCx
BYP
Analog Power Supplies
Bypass
Analog Power Supplies.
A 0.1 μF capacitor connected between BYP and AGND ensures optimum
settling time.
37
TSTA
Test Pin
Connect This Pin to AGND.
38, 71 to 73
NC
NC
No Connect. No internal connection.
40, 42, 44, 46,
48, 50, 52, 54,
56, 58, 60, 62
VID0 to VID11
Analog Outputs
These pins are connected directly to the analog inputs of the LCD panel.
64
VRL
Video Center Reference
Full-Scale Reference
This Voltage Sets the Video Center Voltage. The video outputs are above
this reference while INV = HIGH and below this reference while INV = LOW.
Twice the voltage applied between VRH and VRL sets the full-scale
video output voltage.
65, 66
VRH
Rev. 0 | Page 7 of 16
AD8387
TYPICAL PERFORMANCE CHARACTERISTICS
5.0
4.5
4.0
3.5
3.0
5.0
4.5
4.0
3.5
3.0
2.5
2.0
1.5
1.0
0.5
0
CODE 0
2.5
ΔVP
2.0
CODE 2048
1.5
ΔVDE
1.0
CODE 4095
0.5
ΔVN
0
0
512
1024
1536
2048
2560
3072
3584
4096
0
10
20
30
40
50
60
70
80
INPUT CODE
AMBIENT TEMPERATURE (°C)
Figure 5. Channel Matching vs. Code @ TA = 25°C
Figure 8. Channel Matching vs. TA @ Codes 0, 2048, 4095
3.5
5
4
2.5
1.5
3
2
1
0.5
0
–0.5
–1.5
–2.5
–3.5
–1
–2
–3
–4
–5
0
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
4096
INPUT CODE
INPUT CODE
Figure 9. VCME vs. Code
Figure 6. VDE vs. Code
1.0
0.8
1.0
0.8
0.6
0.6
0.4
0.4
0.2
0.2
0
0
–0.2
–0.4
–0.6
–0.8
–1.0
–0.2
–0.4
–0.6
–0.8
–1.0
0
512
1024
1536
2048
2560
3072
3584
4096
0
512
1024
1536
2048
2560
3072
3584
4096
INPUT CODE
INPUT CODE
Figure 10. DNL vs. Code @ TA = 25°C, INV = L
Figure 7. DNL vs. Code @ TA = 25°C, INV = H
Rev. 0 | Page 8 of 16
AD8387
TIMING DIAGRAMS
SINGLE DATA BUS CONFIGURATION, DSW = LOW
12-CHANNEL
LCD
DBA(0:11)
DBB(0:11)
CLK
12
D(0:11)
VID0
VID1
VID2
VID3
VID4
VID5
VID6
VID7
VID8
VID9
VID10
VID11
CHANNEL 0
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL 5
CHANNEL 6
CHANNEL 7
CHANNEL 8
CHANNEL 9
CHANNEL 10
CHANNEL 11
PIXEL
CLK
÷2
CLK
XFR
R/L
AD8387
XFR
R/L
INV
INV
IMAGE
DSW
ISW
PROCESSOR
REFERENCES
VRH
VRL
VRH
VRL
Figure 11. AD8387 in Single Data Bus System
LEFT
RIGHT
PIXEL CLK
PIXEL CLK
D(0:11)
–3
–
2
–
1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
D(0:11)
–3
–
2
–
1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15 16 17 18 19 20 21 22 23 24
CLK
XFR
CLK
XFR
R/L
R/L
VID0
VID1
VID2
VID3
VID4
VID5
–12
–11
–10
–9
0
1
2
3
4
5
12
13
14
15
16
17
VID0
VID1
VID2
VID3
VID4
VID5
–1
–2
–3
–4
–5
–6
11
10
9
23
22
21
20
19
18
8
–8
7
–7
6
VID6
VID7
–6
–5
–4
–3
–2
–1
6
18
19
20
21
22
23
VID6
VID7
–7
–8
–9
5
4
3
2
1
0
17
16
15
14
13
12
7
VID8
8
VID8
VID9
9
VID9
–10
–11
–12
VID10
VID11
10
11
VID10
VID11
Figure 12. AD8387 in Single Data Bus Configuration Scanning Left-to-Right and Right-to-Left
Rev. 0 | Page 9 of 16
AD8387
DUAL DATA BUS CONFIGURATION, DSW = HIGH
12
12-CHANNEL
LCD
DA(0:11)
DBA(0:11)
DBB(0:11)
CLK
12
VID0
VID1
VID2
VID3
VID4
VID5
VID6
VID7
VID8
VID9
VID10
VID11
CHANNEL 0
CHANNEL 1
CHANNEL 2
CHANNEL 3
CHANNEL 4
CHANNEL 5
CHANNEL 6
CHANNEL 7
CHANNEL 8
CHANNEL 9
CHANNEL 10
CHANNEL 11
DB(0:11)
PIXEL
CLK
÷2
CLK
AD8387
XFR
R/L
INV
XFR
R/L
INV
DVCC
IMAGE
PROCESSOR
DSW
ISW
REFERENCES
VRH
VRL
VRH
VRL
Figure 13. AD8387 in Dual Data Bus System
LEFT
RIGHT
PIXEL CLK
PIXEL CLK
DBA(0:11)
DBB(0:11)
DBA(0:11)
DBB(0:11)
–2
–1
0
1
2
3
4
5
6
7
8
9
10 12 14 16 18 20 22 24
11 13 15 17 19 21 23 25
–1
–2
1
0
3
5
4
7
6
9
8
11 13 15 17 19 21 23 25
10 12 14 16 18 20 22 24
2
CLK
XFR
CLK
XFR
R/L
R/L
VID0
VID1
VID2
VID3
VID4
VID5
–12
0
1
2
3
4
5
12
VID0
VID1
VID2
VID3
VID4
VID5
–1
–2
–3
–4
–5
–6
11
10
9
23
–11
–10
–9
13
14
15
16
17
22
21
20
19
18
8
–8
7
–7
6
VID6
VID7
–6
–5
–4
–3
–2
–1
6
18
19
20
21
22
23
VID6
VID7
–7
–8
–9
5
4
3
2
1
0
17
16
15
14
13
12
7
VID8
8
VID8
VID9
9
VID9
–10
–11
–12
VID10
VID11
10
11
VID10
VID11
Figure 14. AD8387 in Dual Data Bus Configuration Scanning Left-to-Right and Right-to-Left
Rev. 0 | Page 10 of 16
AD8387
t6
CLK
V
V
TH
TH
t5
t1
t2
t2
t1
DB(0:11)
V
XFR
TH
t3
t4
Figure 15. Input Timing (DSW = LOW)
CLK
–2 –1
0
1
2
3
4
5
6
7
8
9
10 11 12 13 14 15
DB(0:11)
XFR
INV
VRL + VFS
50%
VID(0:11)
VRL
VRL
t7
t8
t7
VRL–VFS
PIXELS
–12, –11, –10, –9, –8, –7, –6, –5, –4, –3, –2, –1
PIXELS
0, 1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11
Figure 16. Output Timing (DSW = LOW)
Table 4.
Parameter
Conditions
Min
0
0
3.5
3.5
2.5
3.0
3.5
4.0
Typ
Max
Unit
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
ns
Data Setup Time: t1
XFR Setup Time: t3
Data Hold Time: t2
XFR Hold Time: t4
CLK High Time: t5
CLK Low Time: t6
CLK High Time: t7
CLK Low Time: t8
DSW = HIGH
DSW = HIGH
DSW = LOW
DSW = LOW
Data Switching Delay: t7
Data Switching Delay Skew: Δt7
Invert Switching Delay: t8
15.7
16.2
VIDx = 5 V step
4
4
Invert Switching Delay Skew: Δt8
Rev. 0 | Page 11 of 16
AD8387
FUNCTIONAL DESCRIPTION
Right/Left Control—Input Data Loading
The AD8387 is a system building block designed to directly
drive the columns of LCD microdisplays of the type popularized
for use in projection systems. It has 12 channels of precision,
12-bit DACs loaded from a dual, high speed, 12-bit wide input.
Precision current feedback amplifiers, providing well damped
pulse response and fast voltage settling into large capacitive
loads, buffer the 12 outputs. Laser trimming at the wafer level
ensures low absolute output errors and tight channel-to-channel
matching. Tight part-to-part matching in high resolution
systems is guaranteed by the use of external voltage references.
To facilitate image mirroring, the direction of the loading
sequence is set by the R/L control. A new loading sequence
begins at Channel 0 and proceeds to Channel 11 when the R/L
control is held LOW. It begins at Channel 11 and proceeds to
Channel 0 when the R/L control is held HIGH.
TSW Control—Thermal Switch Control
When this input is HIGH, the thermal switch is enabled. When
LOW or left unconnected, the thermal switch is disabled.
REFERENCE AND CONTROL INPUT DESCRIPTION
Data Transfer/Start Sequence Control—Input Data
Loading, Data Transfer
An internal, 10 kΩ pull-down resistor disables the thermal
switch when this pin is left unconnected.
GSW Control—Output Mode Switch
A valid XFR is initiated when it is held HIGH during a rising
CLK edge.
When this input is HIGH, the video outputs operate normally.
When LOW or left open, the video outputs are forced to
AGND. This function operates when AVCC power is off but
requires DVCC power to be on.
Data is transferred to the outputs and a new loading sequence is
initiated on the next rising CLK edge, immediately following a
valid XFR.
INV Control and ISW Control—Analog Output Inversion
During a loading sequence, 12-bit words are loaded sequentially
into 12 internal channels.
When ISW = LOW, the analog outputs’ transfer function is
below VRL, while INV is held LOW, and is above VRL, while
INV is held HIGH.
When the AD8387 is configured for single data bus (DSW =
LOW), data is loaded on both the rising and falling edges of
CLK. When configured for dual data bus (DSW = HIGH),
data is loaded on the rising edges of CLK only.
With ISW = HIGH, the analog outputs’ transfer function is
above VRL for VID(0, 2, 4, 6, 8, 10) and is below VRL for
VID(1, 3, 5, 7, 9, 11), while INV is held HIGH. Conversely, the
analog outputs’ transfer function is below VRL for VID(0, 2, 4,
6, 8, 10) and is above VRL for VID(1, 3, 5, 7, 9, 11), while INV is
held LOW.
DSW Control—Data Mode Switch
When this input is HIGH, the AD8387 is in dual data bus
mode. Data is loaded from both DBA(0:11) and DBB(0:11)
on the rising CLK edge simultaneously. R/L does not change
the active CLK edge in dual data bus mode. When LOW, the
AD8387 is in single data bus mode. Data is loaded on the rising
CLK edge from DBA(0:11) and on the falling CLK edge from
DBB(0:11) when R/L is LOW. With R/L HIGH, data is loaded
on the falling CLK edge from DBA(0:11) and on the rising CLK
edge from DBB(0:11).
VRH, VRL Inputs—Full-Scale Video Reference Inputs
Two times the difference between VRH and VRL (analog input
voltages) sets the full-scale output voltage.
VFS = 2 × (VRH − VRL)
Rev. 0 | Page 12 of 16
AD8387
THEORY OF OPERATION
TRANSFER FUNCTION AND ANALOG OUTPUT
VOLTAGE
ACCURACY
To best correlate transfer function errors to image artifacts, the
overall accuracy of the DecDriver is defined by three
parameters, VDE , VCME, and ΔVDE.
The DecDriver has two regions of operation where the video
output voltages are either above or below the reference voltage
VRL. The transfer function defines the video output voltage as
the function of the digital input code as:
VDE, the differential error voltage, measures the difference
between the rms value of a channel and the ideal rms value of
that channel. The defining expression is
VOUTN(n) = VIDx(n) = VRL + VFS × (1 − n/4095),
for INV = HIGH
⎡
⎤
VOUTN(n) − VOUTP(n)
n
⎞
4095 ⎠
⎣
⎦
⎛
⎝
VOUTP(n) = VIDx(n) = VRL − VFS × (1 − n/4095),
for INV = LOW
VDE(n) =
− 1 −
×VFS
⎟
⎜
2
VCME, the common-mode error voltage, measures ½ the dc
bias of a channel. The defining expression is
where n is the input code.
VFS = 2 × (VRH − VRL)
VOUTN(n) + VOUTP(n)
⎡
⎤
1
2
VCME(n) =
− VRL
A number of internal limits define the usable range of the video
output voltages, VIDx, as shown in Figure 17.
⎢
⎣
⎥
⎦
2
ΔVDE measures the maximum VDE mismatch between
channels. The defining equation is
VIDx – VOLTS
AVCC
≥1.3V
(VRL + VFS)
ΔVDE = max{VDE(n)(0 − 11)} − min{VDE(n)(0 − 11)
}
VOUTN
VOUTP
0 ≤ VFS ≤ 5.25V
ΔV measures the maximum mismatch between channels. The
defining expression is
11V ≤ AVCC
≤ 18V
VRL
ΔV(n) = max{ΔVN(n), ΔVP(n)}
0 ≤ VFS
5.25V ≤ VRL
≤ (AVCC – 4)
where:
≤ 5.25V
(VRL – VFS)
AGND
ΔVN(n) = max{VOUTN(n)(0 − 11)} − min{VOUTN(n)(0 − 11)
}
≥1.3V
0
INPUT CODE
VIDx vs. INPUT CODE
4095
ΔVP(n) = max{VOUTP(n)(0 − 11)} − min{VOUTP(n)(0 − 11)
}
INTERNAL LIMITS AND
USABLE VOLTAGE RANGES
Figure 17. AD8387 Transfer Function and Usable Voltage Ranges
Rev. 0 | Page 13 of 16
AD8387
APPLICATIONS
OPTIMIZED RELIABILITY WITH THE THERMAL
SWITCH
POWER-OFF SEQUENCE
1. Turn off input signals
While internal current limiters provide short-term protection
against temporary shorts at the outputs, the thermal switch
provides protection against persistent shorts lasting for several
seconds. To optimize reliability with the use of the thermal
switch, the following sequence of operations is recommended.
2. Turn off VRL
3. Turn off VRH
4. Turn off AVCC
5. Turn off DVCC
GROUNDED OUTPUT MODE DURING POWER-OFF
INITIAL POWER-UP AFTER ASSEMBLY OR REPAIR
Certain applications require that video outputs be held near
AGND during power-down. The following power-off sequence
ensures that the outputs are near ground during power-off and
that the Absolute Maximum Ratings are not violated.
Grounded output mode is disabled, and thermal switch is
enabled. Ensure that the GSW pin is HIGH and that the
TSW pin is HIGH upon initial power-up and that they remain
unchanged throughout this procedure.
1. Enable grounded output mode: GSW = LOW
2. Turn off input signals
3. Turn off VRL
The initial power-up sequence follows:
1. Execute the initial power-up.
2. Identify any shorts at outputs. Power down, repair shorts,
and repeat the initial power-up sequence until proper system
functionality is verified.
4. Turn off VRH
5. Turn off AVCC
3. Disable the thermal switch.
6. Turn off DVCC
POWER-UP DURING NORMAL OPERATION
PCB DESIGN FOR OPTIMIZED THERMAL
PERFORMANCE
Grounded output mode is disabled, and thermal switch is
disabled.
Although the maximum safe operating junction temperature is
higher, the AD8387 is 100% tested at a junction temperature of
125°C. Consequently, the maximum guaranteed operating
junction temperature is 125°C. To limit the maximum junction
temperature at or below the guaranteed maximum, the package
in conjunction with the PCB must effectively conduct heat away
from the junction.
If TSW = LOW and GSW = HIGH, all outputs go into normal
operating mode with the thermal switch disabled.
POWER SUPPLY SEQUENCING
As indicated under the Absolute Maximum Ratings, the voltage
at any input pin cannot exceed its supply voltage by more than
0.5 V. Power-on and power-off sequencing can be required to
comply with the absolute maximum ratings.
The AD8387 package is designed to provide enhanced thermal
characteristics through the exposed die paddle on the bottom
surface of the package. To take full advantage of this feature, the
exposed paddle must be in direct thermal contact with the PCB,
which then serves as a heat sink.
Failure to comply with the Absolute Maximum Ratings can
result in functional failure or damage to the internal ESD
diodes. Damaged ESD diodes can cause temporary parametric
failures, which can result in image artifacts. Damaged ESD
diodes cannot provide full ESD protection, reducing reliability.
A thermally effective PCB must incorporate two thermal
pads and a thermal via structure. The thermal pad on the top
surface of the PCB provides a solderable contact surface on the
top surface of the PCB. The thermal pad on the bottom PCB
layer provides a surface in direct contact with the ambient. The
thermal via structure provides a thermal path to the inner and
bottom layers of the PCB to remove heat.
POWER-ON SEQUENCE
1. Turn on AVCC
2. Turn on VRH
3. Turn on VRL
4. Turn on DVCC
5. Disable thermal switch: TSW = LOW
6. Turn on input signals
Rev. 0 | Page 14 of 16
AD8387
THERMAL PAD DESIGN
To minimize thermal performance degradation of production
PCBs, the contact area between the thermal pad and the PCB
should be maximized. Therefore, the size of the thermal pad
on the top PCB layer should match the exposed paddle. The
second thermal pad of the same size should be placed on the
bottom side of the PCB. At least one thermal pad should be in
direct thermal contact with an external plane, such as AVCC
or GND.
16mm
6.5mm
THERMAL VIA STRUCTURE DESIGN
Effective heat transfer from the top to the inner and bottom
layers of the PCB requires thermal vias incorporated into the
thermal pad design. Thermal performance increases
logarithmically with the number of vias.
Figure 18. Land Pattern—Top Layer
Near optimum thermal performance of production PCBs is
attained only when tightly spaced thermal vias are placed on
the full extent of the thermal pad.
6.5mm
Thermal Pad and Thermal via Connections
The thermal pad on the solder side is connected to a plane. The
use of thermal spokes is not recommended when connecting
the thermal pads or via structure to the plane.
Solder Masking
Figure 19. Land Pattern—Bottom Layer
Solder masking of the via holes on the top layer of the PCB
plugs the via holes, inhibiting solder flow into the holes. To
minimize the formation of solder voids due to solder flowing
into the via holes (solder wicking), via diameter should be made
small, and an optional solder mask can be used. To optimize the
thermal pad coverage when using the solder mask, its diameter
should be no more than 0.1 mm larger than the via hole
diameter.
Pads are set by customer’s PCB design rules.
Thermal via Holes—Circular mask, centered on the via holes.
Diameter of the mask should be 0.1 mm larger than the via hole
diameter.
Figure 20. Solder Mask—Top Layer
Solder Mask—Bottom Layer
This is set by customer’s PCB design rules.
AD8387 PCB DESIGN RECOMMENDATIONS
Table 5. Land Pattern Dimensions
Pad Size
Pad Pitch
Thermal Pad Size
Thermal Via Structure
0.25 mm − 0.35 mm holes
0.5 mm − 1.0 mm grid
0.6 mm × 0.25 mm
0.5 mm
6 mm × 6 mm
Rev. 0 | Page 15 of 16
AD8387
OUTLINE DIMENSIONS
14.20
14.00 SQ
13.80
12.20
1.20
MAX
12.00 SQ
11.80
0.75
0.60
0.45
61
80
80
61
1
60
1
60
PIN 1
EXPOSED
PAD
6.00
BSC SQ
TOP VIEW
(PINS DOWN)
BOTTOM VIEW
(PINS UP)
0° MIN
1.05
1.00
0.95
0.20
0.09
7°
20
41
41
20
40
40
21
21
3.5°
0°
VIEW A
0.15
0.05
0.50 BSC
LEAD PITCH
0.27
0.22
0.17
SEATING
PLANE
0.08 MAX
COPLANARITY
VIEW A
ROTATED 90° CCW
COMPLIANT TO JEDEC STANDARDS MS-026-ADD-HD
Figure 21. 80-Lead Thin Quad Flat Package, Exposed Pad [TQFP_EP]
(SV-80-1)
Dimensions shown in millimeters
ORDERING GUIDE
Model
AD8387JSVZ1
Temperature Range
0°C to 85°C
Package Description
80-Lead TQFP
Package Option
SV-80-1
AD8387-EB
Evaluation Board
1 Z = Pb-free part.
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05653-0-10/05(0)
Rev. 0 | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明