AD9576_技术文档

Dual PLL,

Asynchronous Clock Generator

Data Sheet

AD9576

FEATURES

FUNCTIONAL BLOCK DIAGRAM

Single, low phase noise, fully integrated VCO/fractional-N

PLL core

2

SPI/I C

STATUS

MONITOR

AND PPRx

CONTROL

VCO range: 2375 MHz to 2725 MHz

OPTIONAL

REF2

Integrated loop filter (requires a single external capacitor)

2 differential, XTAL, or single-ended reference inputs

Reference monitoring capability

DIV

OUT10

GENERAL-

PURPOSE

PLL

OUT9

OUT8

Automatic redundant XTAL switchover

Minimal transient, smooth switching

Typical RMS jitter

OUT0

OUT1

OUT2

OUT3

DIV

OPTIONAL

REF0

<0.3 ps (12 kHz to 20 MHz), integer-N translations

<0.5 ps (12 kHz to 20 MHz), fractional-N translations

Input frequency

VCO

OUT4

OUT5

DIV

REF1

OUT6

OUT7

VCO

DIV

8 kHz, 1.544 MHz, 2.048 MHz, and 10 MHz to 325 MHz

Preset frequency translations via pin strapping (PPRx)

Using a 25 MHz input reference

AD9576

24.576 MHz, 25 MHz, 33.33 MHz, 50 MHz, 70.656 MHz,

100 MHz, 125 MHz, 148.5 MHz, 156.25 MHz,

161.1328 MHz, 312.5 MHz, 322.2656 MHz, 625 MHz,

or 644.5313 MHz

Figure 1.

GENERAL DESCRIPTION

The AD9576 provides a multiple output clock generator

function comprising two dedicated phase-locked loop (PLL)

cores with flexible frequency translation capability, optimized to

serve as a robust source of asynchronous clocks for an entire

system, providing extended operating life within frequency

tolerance through monitoring of and automatic switchover

between redundant crystal (XTAL) inputs with minimized

switching, induced transients. The fractional-N PLL design is

based on the Analog Devices, Inc., proven portfolio of high

performance, low jitter frequency synthesizers to maximize

network performance, whereas the integer-N PLL provides

general-purpose clocks for use as CPU and field-programmable

gate array (FPGA) reference clocks.

Using a 19.44 MHz input reference

50 MHz, 100 MHz, 125 MHz, 156.25 MHz, 161.1328 MHz,

or 644.5313 MHz

Using a 30.72 MHz input reference

25 MHz, 50 MHz, 100 MHz, 125 MHz, or 156.25 MHz

Single, general-purpose, fully integrated VCO/integer-N

PLL core

VCO range: 750 MHz to 825 MHz

Integrated loop filter

Independent, duplicate reference input or operation from

the fractional-N PLL active reference input

Input frequency: 25 MHz

Preset frequency translations via pin strapping (PPRx)

25 MHz, 33.33 MHz, 50 MHz, 66.67 MHz, 100 MHz,

133.33 MHz, 200 MHz, or 400 MHz

The AD9576 uses pin strapping to select among a multitude of

power-on ready configurations for its 11 output clocks, which

require only the connection of external pull-up or pull-down

resistors to the appropriate pin program reader pins (PPRx).

These pins provide control of the internal dividers for establishing

the desired frequency translations, clock output functionality,

and input reference functionality. These parameters can also be

manually configured through a serial port interface (SPI).

Up to 3 copies of reference clock output

11 pairs of configurable differential outputs

Output drive formats

3 outputs: HSTL, LVDS, HCSL, 1.8 V CMOS, 2.5 V/3.3 V CMOS

8 outputs: HSTL, LVDS, or 1.8 V CMOS

2.5 V or 3.3 V single-supply operation

The AD9576 is packaged in a 64-lead, 9 mm × 9 mm LFCSP,

requiring only a single 2.5 V or 3.3 V supply. The operating

temperature range is −40°C to +85°C.

APPLICATIONS

Ethernet line cards, switches, and routers

Baseband units

Each OUTx output is differential and contains two pins: OUTx

SATA and PCI express

OUTx

and

. For simplicity, the term OUTx refers to the

Low jitter, low phase noise clock generation

Asynchronous clock generation

functional output block containing these two pins.

Rev. A

Document Feedback

Information furnished by Analog Devices is believed to be accurate and reliable. However, no

responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other

rights of third parties that may result from its use. Specifications subject to change without notice. No

license is granted by implication or otherwise under any patent or patent rights of Analog Devices.

Trademarks and registered trademarks are the property of their respective owners.

One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.

Technical Support

www.analog.com

AD9576

Data Sheet

TABLE OF CONTENTS

Features .............................................................................................. 1

PLL0 Integer-N/Fractional-N PLL........................................... 29

PLL1 Integer-N PLL................................................................... 35

Output Distribution................................................................... 36

PPRx Pins .................................................................................... 38

Power-On Reset (POR) ............................................................. 41

Serial Control Port ......................................................................... 42

SPI/I²C Port Selection................................................................ 42

SPI Serial Port Operation.......................................................... 42

I²C Serial Port Operation .......................................................... 44

Control Register Map..................................................................... 48

Control Register Descriptions ...................................................... 51

Applications....................................................................................... 1

Functional Block Diagram .............................................................. 1

General Description......................................................................... 1

Revision History ............................................................................... 3

Specifications..................................................................................... 4

Conditions..................................................................................... 4

Supply Current Specifications..................................................... 4

Power Dissipation Specifications ............................................... 5

Reference Inputs ........................................................................... 6

Reference Switchover Output Disturbance Specifications...... 6

PLL0 Characteristics .................................................................... 7

PLL1 Characteristics .................................................................... 7

Clock Distribution Outputs Specifications............................... 7

Output Alignment and Startup Specifications ....................... 10

PLL0 Channels Absolute Clock Jitter Specifications ............. 11

Serial Port Configuration Registers (Register 0x000 to

Register 0x00F)........................................................................... 51

Status Indicator Registers (Register 0x020 to Register 0x021) .. 52

Chip Mode Register (Register 0x040) ..................................... 52

Reference Input Configuration Registers (Register 0x080 to

Register 0x081) ........................................................................... 53

PLL1 and Bypass Channel Absolute Clock Jitter

Reference Switchover Registers (Register 0x082 to

Specifications .............................................................................. 13

Register 0x083) ........................................................................... 54

OUT8 to OUT10 Channel Cycle to Cycle Clock Jitter

PLL0 Configuration Registers (Register 0x100 to

Specifications .............................................................................. 13

Register 0x111) ........................................................................... 55

RESET

Logic Input Pins Characteristics—REF_SEL,

, SPx,

PLL0 VCO Dividers Registers (Register 0x120 to

PPRx............................................................................................. 14

Register 0x122) ........................................................................... 57

Status Output Pins Characteristics—LD_0, LD_1, REF_SW,

REF_STATUS, REF_ACT ......................................................... 14

PLL0 Distribution Registers (Register 0x140 to

Register 0x14D).......................................................................... 58

Serial Control Port Specifications ............................................ 15

Absolute Maximum Ratings.......................................................... 17

Thermal Resistance .................................................................... 17

ESD Caution................................................................................ 17

Pin Configuration and Function Descriptions........................... 18

Typical Performance Characteristics ........................................... 22

Phase Noise and Voltage Waveforms....................................... 22

Reference Switching Frequency and Phase Disturbance ...... 24

Terminology .................................................................................... 25

Theory of Operation ...................................................................... 26

Overview...................................................................................... 26

Reference Inputs ......................................................................... 26

Reference Monitor...................................................................... 27

Reference Switching ................................................................... 28

PLL1 Configuration Registers (Register 0x200 to

Register 0x202) ........................................................................... 60

PLL1 Distribution Registers (Register 0x240 to

Register 0x246) ........................................................................... 60

Applications Information.............................................................. 63

Interfacing to CMOS Clock Outputs....................................... 63

Interfacing to LVDS and HSTL Clock Outputs ..................... 63

Interfacing to HCSL Clock Outputs ........................................ 63

Power Supply............................................................................... 64

Power and Grounding Considerations and Power Supply

Rejection...................................................................................... 64

Outline Dimensions....................................................................... 65

Ordering Guide .......................................................................... 65

Rev. A | Page 2 of 65

Data Sheet

AD9576

REVISION HISTORY

9/2018—Rev. 0 to Rev. A

Change to Table 47, Address 0x103, Bits[5:3], Reset Column.....55

Updated Outline Dimensions........................................................65

7/2016—Revision 0: Initial Version

Rev. A | Page 3 of 65

AD9576

Data Sheet

SPECIFICATIONS

Typical values are given for V_{DD_x}= 2.5 V, T_A= 25°C, unless otherwise noted. Minimum and maximum values are given over the full V_{DD_x}

and T_A(−40°C to +85°C) range.

VDD_x and V_{DD_x}refer to the following pins, and to the voltage on any of the following pins, respectively: VDD_REFMON, VDD_REF0,

VDD_REF1, VDD_IO, VDD_PLL0, VDD_VCO0, VDD_M0, VDD_M1, VDD_OUT67, VDD_OUT45, VDD_OUT23, VDD_OUT01,

VDD_OUT89, VDD_OUT10, VDD_VCO1, VDD_PLL1, and VDD_REF2.

Note that throughout this data sheet, multifunction pins, such as SCLK/SCL, are referred to either by the entire pin name or by a single

function of the pin, for example, SCLK, when only that function is relevant.

CONDITIONS

Table 1.

Parameter

Min Typ Max Unit Test Conditions/Comments

Applies to all VDD_x pins; 2.5 V and 3.3 V nominal supplies are supported on all

POWER SUPPLY

VOLTAGE

specifications, unless otherwise noted

(V_{DD_x}

)

2.38

2.97

2.63

3.63

V

2.5 V 5%

3.3 V 10%

SUPPLY CURRENT SPECIFICATIONS

Table 2.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

SUPPLIES OTHER THAN CLOCK

OUTPUT DRIVERS

All blocks running (excludes clock distribution section); REF0

(differential) and REF1 (differential) at 300 MHz; PLL0 locked at

2500 MHz with a 100 MHz phase frequency detector (PFD) rate;

Divider M0 set to 2 and Divider M1 disabled; REF2 (XTAL) at

25 MHz, configured as PLL1 input; PLL1 locked to 800 MHz with

input doubler enabled

VDD_REFMON and VDD_REFx

(Pin 4, Pin 9, Pin 10, and

Pin 64)

35.6

26.5

39.2

29.5

mA

Cumulative current draw from all listed supply pins

VDD_IO and VDD_PLL0 (Pin 16

and Pin 18)

Cumulative current draw from all listed supply pins

VDD_VCO0 (Pin 21)

VDD_Mx (Pin 23 and Pin 25)

VDD_VCO1 (Pin 60)

VDD_PLL1 (Pin 61)

33.8

81.0

19.2

20.4

36.9

88.7

21.8

23.7

mA

Cumulative current draw from all listed supply pins

SUPPLY CURRENT FOR EACH

CLOCK DISTRIBUTION SUPPLY

Output driver supplies power both the output driver and output

divider

High Speed Transceiver Logic

(HSTL)

VDD_OUT67 (Pin 29)

VDD_OUT45 (Pin 35)

VDD_OUT23 (Pin 41)

VDD_OUT01(Pin 46)

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

59.8

46.7

36.4

57.4

34.2

69.7

53.8

42.6

67.1

39.5

mA

Output at 1250 MHz

Output at 625 MHz

Output at 400 MHz

Low Voltage Differential

Signaling (LVDS)

VDD_OUT67 (Pin 29)

VDD_OUT45 (Pin 35)

VDD_OUT23 (Pin 41)

VDD_OUT01(Pin 46)

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

41.3

31.1

20.8

37.5

24.1

49.2

34.9

23.6

43.6

27.7

mA

Output at 1250 MHz

Output at 625 MHz

Output at 400 MHz

Rev. A | Page 4 of 65

Data Sheet

AD9576

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

1.8 V CMOS

All outputs at 100 MHz with a 10 pF load

VDD_OUT67 (Pin 29)

27.2

28.2

17.4

32.7

21.4

34.7

31.7

21.9

42.5

26.8

mA

VDD_OUT45 (Pin 35)

VDD_OUT23 (Pin 41)

VDD_OUT01(Pin 46)

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

2.5 V CMOS

V_{DD_x}set to 2.5 V, output at 100 MHz with a 10 pF load; not

available on OUT0 to OUT7

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

3.3 V CMOS

38.5

24.4

48.8

30.1

mA

V_{DD_x}set to 3.3 V, all outputs at 100 MHz with a 10 pF load; not

available on OUT0 to OUT7

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

48.5

29.1

60.4

36.2

mA

High Speed Current Sinking

Logic (HCSL)

All outputs at 400 MHz; not available on OUT0 to OUT7

VDD_OUT89 (Pin 52)

VDD_OUT10 (Pin 57)

30.7

20.8

41.4

26.6

mA

POWER DISSIPATION SPECIFICATIONS

Table 3.

Parameter

Min Typ

Max

Unit

Test Conditions/Comments

POWER DISSIPATION

All supplies set to 2.5 V nominal; specifications do not include power

dissipated by external terminations

Typical Configuration 1

Typical Configuration 2

680

1168

mW

Asynchronous operation; PPR0 = State 0, PPR1 = State 0, PPR2 = State 3,

PPR3 = State 3; REF 0 and REF1 = 25 MHz XTAL, doubler enabled; OUT10 =

25 MHz CMOS; OUT0 to OUT3 = 100 MHz LVDS; OUT4 to OUT5 = 312.5 MHz

LVDS, OUT6 to OUT7 = 156.25 MHz LVDS, OUT8 to OUT9 = 125 MHz LVDS

619

979

145

974

mW

Synchronous operation; REF0 (differential) at 100 MHz, REF1 disabled, and

REF2 (XTAL) at 25 MHz; PLL1 disabled and PLL0 locked at 2500 MHz using R

divider of 2 and PLL0 feedback divider (N0) set to 50; M0 and M1 set to

divide by 2; Output 0 set to 625 MHz HSTL; Output 1 to Output 3 disabled;

Output 4 to Output 7 set to 125 MHz LVDS; Output 8 to Output 9 set to

156.25 MHz LVDS

All Blocks Running

1520

179

All blocks running; REF0 (differential) and REF1 (differential) at 300 MHz;

PLL0 locked at 2500 MHz with a 100 MHz PFD rate; M0 set to 2 and enabled to

Q0, Q1, and Q2; OUT0 to OUT3 = 625 MHz LVDS; OUT4 to OUT 7 = 1250 MHz

LVDS; REF2 (XTAL) at 25 MHz, configured as PLL1 input; PLL1 locked to

800 MHz with input doubler enabled; Divider Q3 and Divider Q4 set to 2 and

OUT8 to OUT10 = 400 MHz, HCSL

Minimal Power

Configuration

PPR0 = State 0, PPR1 = State 0, PPR2 = State 0, PPR3 = State 0

INCREMENTAL POWER

DISSIPATION

Typical configuration; values show the change in power due to the indicated

operation

Input Reference On/Off

Single-Ended

Applies to one reference clock input at 25 MHz

2.5

10

mW

Differential

27.5

33.7

Output Driver On/Off

LVDS at 156.25 MHz

HSTL at 156.25 MHz

47.6

51.3

64.6

66.1

80.8

74.1

mW

1.8 V CMOS at

100 MHz

A single 1.8 V CMOS output with a 10 pF load

A single 2.5 V CMOS output with a 10 pF load

2.5 V CMOS at

100 MHz

88.4

102.5

mW

Rev. A | Page 5 of 65

AD9576

Data Sheet

REFERENCE INPUTS

Table 4.

Parameter

Min

Typ Max

Unit

Test Conditions/Comments

DIFFERENTIAL INPUT MODE

Input Frequency

Input Sensitivity

Minimum Input Slew Rate

325

MHz

100

mV p-p

V/µs

Minimum limit imposed for jitter performance (when using

a sinusoidal source)

Minimum Pulse Width

1.38

0.83

ns

V

Applies to both low and high pulses

Common-Mode Internally Generated

Bias Voltage

1.24

Common-Mode Voltage Tolerance

1.675

V

The acceptable common-mode range for a 200 mV p-p,

dc-coupled input signal

Differential Input Capacitance

Differential Input Resistance

SINGLE-ENDED INPUT CMOS MODE

Input Frequency

2

pF

4.3

kΩ

200

MHz

ns

Minimum Pulse Width

Hysteresis

2

Applies to both low and high pulses

240

2

mV

nA

Input Leakage

Input Capacitance

Input Voltage

2

pF

High

1.93

V

Low

1.04

CRYSTAL RESONATOR MODE

Input Frequency

Fundamental mode quartz resonator

Reference of PLL0 or Buffered

Output

19.44

30.72 MHz

Reference of PLL1

25

3

MHz

Ω

REF2

Effective Series Resistance (ESR)

Input Capacitance

80

pF

REFERENCE SWITCHOVER OUTPUT DISTURBANCE SPECIFICATIONS

Table 5.

Parameter

Min Typ

Max

Unit

Test Conditions/Comments

INSTANTANEOUS FREQUENCY (dθ/dt)

DISTURBANCE DUE TO REFERENCE

SWITCHOVER

350

ppm

peak

Applies only to PLL0 outputs; 1 ppm frequency offset

between the REF0 and REF1 channels; 400 kHz loop

bandwidth; smooth switchover enabled

INSTANTANEOUS PHASE DISTURBANCE

DUE TO REFERENCE SWITCHOVER

220

ps

Applies only to the active reference of PLL0; smooth

switchover enabled

Rev. A | Page 6 of 65

Data Sheet

AD9576

PLL0 CHARACTERISTICS

Table 6.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

REFERENCE INPUT PATH

Input Frequency

Divider

325

145

MHz

Doubler

PHASE FREQUENCY DETECTOR (PFD)

Frequency Range

Integer Mode

290

170

MHz

ppm

Fractional Mode

9.4

Lock Detect Window

16

INPUT FREQUENCY OF FEEDBACK DIVIDERS

N0

2725

156

MHz

N0A

Q_ZD

1250

VOLTAGE CONTROLLED OSCILLATOR (VCO)

Frequency Range

2375

2725

1250

MHz

Gain

64

MHz/V

MHz

VCO DIVIDER (M0 AND M1) OUTPUT FREQUENCY

PLL1 CHARACTERISTICS

Table 7.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

REFERENCE INPUT PATH

Input Frequency

Divider

25

MHz

Doubler

PFD FREQUENCY

Frequency Range

Lock Detector Window

VCO

25

50

MHz

UI

2

Frequency Range

Gain

750

825

MHz

750

MHz/V

CLOCK DISTRIBUTION OUTPUTS SPECIFICATIONS

Rise and fall time measurement thresholds are 20% and 80% of the nominal low and high amplitude of the waveform.

Table 8.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

HSTL (OUT0 TO OUT7)

Output Frequency

OUT0 to OUT3

100 Ω termination (differential)

1000

1250

163

MHz

ps

OUT4 to OUT7

Output Rise Time, t_RL

Output Fall Time, t_FL

Duty Cycle

108

45

136

Measured differentially; output at 100 MHz

161

ps

55

%

Differential Output Voltage Swing

861

1080

940

1374

mV

Magnitude of voltage across pins; output

driver static

Common-Mode Output Voltage

840

1034

mV

Output driver static

Rev. A | Page 7 of 65

AD9576

Data Sheet

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

LVDS (OUT0 TO OUT7)

Output Frequency

OUT0 to OUT3

100 Ω termination (differential)

1000

1250

181

55

MHz

ps

OUT4 to OUT7

Output Rise Time, t_RL

Output Fall Time, t_FL

Duty Cycle

139

141

45

158

159

Measured differentially; output at 100 MHz

ps

%

Differential Output Voltage, V_OD

276

375

490

mV

Magnitude of voltage across pins; output

driver static

Delta V_OD

22

mV

V

Output Offset Voltage, V_OS

Delta V_OS

1.18

1.275

1.36

26

mV

mA

Short-Circuit Current (I_SA, I_SB)

25

Output shorted to GND; value represents the

magnitude of current draw

1.8 V CMOS (OUT0 TO OUT7)

Output Frequency

Output Rise Time, t_RC

Output Fall Time, t_FC

Duty Cycle

C_LOAD= 10 pF

200

1.54

1.49

55

MHz

ns

0.84

1.04

45

1.19

1.25

Output at 25 MHz

ns

%

Output Voltage

High (V_OH)

1.74

V

I_LOAD= −1 mA

Low (V_OL)

0.065

I_LOAD= 1 mA

HSTL (OUT8 TO OUT10)

Output Frequency

Output Rise Time, t_RL

Output Fall Time, t_FL

Duty Cycle

100 Ω termination (differential)

1000

170

55

MHz

ps

124

125

45

144

Measured differentially; output at 100 MHz

Assumes 50% reference input duty cycle

ps

%

Differential Output Voltage Swing

861

1080

940

1374

mV

Magnitude of voltage across pins; output

driver static

Common-Mode Output Voltage

LVDS (OUT8 TO OUT10)

Output Frequency

840

1034

mV

Output driver static

100 Ω termination (differential)

1000

112

113

55

MHz

ps

Output Rise Time, t_RL

65

85

86

Measured differentially; output at 100 MHz

Assumes 50% reference input duty cycle

Output Fall Time, t_FL

66

ps

Duty Cycle

45

%

Differential Output Voltage, V_OD

276

375

490

mV

Magnitude of voltage across pins; output

driver static

∆V_OD

22

mV

V

Output Offset Voltage, V_OS

∆V_OS

1.18

1.275

1.36

26

mV

mA

Short-Circuit Current (I_SA, I_SB)

25

Output shorted to GND; value represents the

magnitude of current draw

1.8 V CMOS (OUT8 TO OUT10)

Output Frequency

Output Rise Time, t_RC

Output Fall Time, t_FC

Duty Cycle

C_LOAD= 10 pF

200

1.41

1.24

55

MHz

ns

0.49

0.59

Output at 25 MHz

ns

Output at 25 MHz

45

%

Assumes 50% reference input duty cycle

Output Voltage

High (V_OH)

1.74

V

I_LOAD= −1 mA

I_LOAD= 1 mA

Low (V_OL)

0.065

Rev. A | Page 8 of 65

Data Sheet

AD9576

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

FULL SWING CMOS (OUT8 TO OUT10)

Output Frequency

Output Rise Time, t_RC

Output Fall Time, t_FC

Duty Cycle

C_LOAD= 10 pF

250

1.38

1.19

55

MHz

ns

0.50

0.57

Output at 25 MHz

ns

45

%

Assumes 50% reference input duty cycle

Output Voltage

High (V_OH)

V_{DD_x}− 0.33

V

I_LOAD= −10 mA

Low (V_OL)

0.25

I_LOAD= 10 mA

HCSL (OUT8 to OUT10)

Output Frequency

Output Rise Time, t_RL

Output Fall Time, t_FL

Duty Cycle

50 Ω from each output pin to GND

800

211

209

55

145

141

45

174

175

ps

%

Measured differentially; output at 100 MHz

Assumes 50% reference input duty cycle

Differential Output Voltage Swing

570

770

400

975

mV

Magnitude of voltage across pins; output

driver static

Common-Mode Output Voltage

295

500

mV

Output driver static

Timing Diagrams

SINGLE-ENDED

80%

CMOS

10pF LOAD

20%

t_RC

t_FC

Figure 2. CMOS Timing, Single-Ended, 10 pF Load

DIFFERENTIAL

80%

LVDS/HSTL/HCSL

20%

t_RL

t_FL

Figure 3. LVDS, HSTL, and HCSL Timing, Differential

Rev. A | Page 9 of 65

AD9576

Data Sheet

OUTPUT ALIGNMENT AND STARTUP SPECIFICATIONS

The indicated times assume the voltage applied to all power supply pins is within specification and stable.

Table 9.

Parameter

Min

Typ Max Unit Test Conditions/Comments

Timing delay between input clock edge on REF0 or REF1 to any

ZERO DELAY

corresponding OUTx clock edge; R divider and doubler are bypassed

OUT0 to OUT7

3.44 3.87 ns

3.82 4.28 ns

OUT8 to OUT9

OUTPUT TO OUTPUT SKEW

Deviation between rising edges of outputs of a similar logic type; frequency

source to distribution is the output of the M0 divider; all output drivers are

configured to the same logic type, unless otherwise noted; all output

frequencies are 25 MHz

Between Outputs that

Share a Single Qx Divider

LVDS

OUT1, OUT2, and

OUT3

−36

+29

ps

Relative to OUT0

OUT5

OUT7

OUT9

HSTL

−13

−19

−22

+30

+15

+20

ps

Relative to OUT4

Relative to OUT6

Relative to OUT8

OUT1, OUT2, and

OUT3

−33

+30

ps

Relative to OUT0

OUT5

−16

−23

+37

+19

+24

ps

Relative to OUT4

Relative to OUT6

Relative to OUT8

OUT7

OUT9

Between OUT0 to OUT9

LVDS

OUT4

−141

−105

229

−8

ps

Relative to OUT0

OUT6

+23

440

OUT8

HSTL

OUT4

−149

−116

271

−12

+17

487

ps

Relative to OUT0

OUT6

OUT8

PROPAGATION DELAY

3.88 4.47 ns

Rising edge on REF2 input to OUT8 to OUT10; 25 MHz reference input clock,

PLL1 bypassed, and Qx dividers set to 1

OUTPUT READY TIME

PLL0

25 MHz reference input clocks, input doublers disabled

Time interval from RESET pin = Logic 1 to LD_0 pin = Logic 1 (PLL0 lock

detection)

8

ms

µs

PLL1

455

Time interval from RESET pin = Logic 1 to LD_1 pin = Logic 1 (PLL1 lock

detection)

Rev. A | Page 10 of 65

Data Sheet

AD9576

PLL0 CHANNELS ABSOLUTE CLOCK JITTER SPECIFICATIONS

Reference input frequency source is a 25 MHz Taitien XTAL, and frequency multiplier (×2) at PLL input enabled, unless otherwise noted.

Table 10.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

HSTL INTEGRATED RMS JITTER

Jitter Integration Bandwidth = 10 kHz to 10 MHz

Integer-N Translations

100 MHz Output

0.233

0.218

0.221

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.291

0.307

0.292

0.313

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

Jitter Integration Bandwidth = 12 kHz to 20 MHz

Integer-N Translations

100 MHz Output

0.239

0.222

0.221

0.222

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.298

0.310

0.296

0.314

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

Jitter Integration Bandwidth = 50 kHz to 80 MHz

312.5 MHz Output

0.237

ps

Jitter Integration Bandwidth = 1.875 MHz to 20 MHz

Integer-N Translations

100 MHz Output

0.088

0.076

0.071

0.053

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.119

0.106

0.103

0.096

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

LVDS INTEGRATED RMS JITTER

Jitter Integration Bandwidth = 10 kHz to 10 MHz

Integer-N Translations

100 MHz Output

0.242

0.227

0.250

0.221

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.351

0.329

0.327

0.313

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

Rev. A | Page 11 of 65

AD9576

Data Sheet

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

Jitter Integration Bandwidth = 12 kHz to 20 MHz

Integer-N Translations

100 MHz Output

0.268

0.240

0.257

0.221

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.412

0.336

0.334

0.314

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

Jitter Integration Bandwidth = 50 kHz to 80 MHz

312.5 MHz Output

0.246

ps

Jitter Integration Bandwidth = 1.875 MHz to 20 MHz

Integer-N Translations

100 MHz Output

0.161

0.117

0.099

0.053

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Fractional-N Translations

70.656 MHz Output

0.298

0.130

0.129

0.095

ps

148.5 MHz Output

153.6 MHz Output

644.53125 MHz Output

HCSL INTEGRATED RMS JITTER

Jitter Integration Bandwidth = 10 kHz to 10 MHz

Integer-N Translations

100 MHz Output

OUT8 and OUT9 only

0.247

0.250

0.273

0.228

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Jitter Integration Bandwidth = 12 kHz to 20 MHz

100 MHz Output

0.263

0.265

0.298

0.229

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Jitter Integration Bandwidth = 50 kHz to 80 MHz

312.5 MHz Output

0.348

ps

Jitter Integration Bandwidth = 1.875 MHz to 20 MHz

100 MHz Output

0.145

0.144

0.176

0.063

ps

125 MHz Output

156.25 MHz Output

625 MHz Output

Rev. A | Page 12 of 65

Data Sheet

AD9576

PLL1 AND BYPASS CHANNEL ABSOLUTE CLOCK JITTER SPECIFICATIONS

Table 11.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

HSTL INTEGRATED RMS JITTER

25 MHz Output

0.125

1.605

1.641

ps

Source = 25 MHz Taitien XTAL; jitter integration bandwidth =

12 kHz to 5 MHz

100 MHz Output

400 MHz Output

Source = PLL1; Qx divider = 8; jitter integration bandwidth =

12 kHz to 20 MHz

Source = PLL1; Qx divider = 2; jitter integration bandwidth =

12 kHz to 20 MHz

HCSL INTEGRATED RMS JITTER

25 MHz Output

0.287

1.54

ps

Source = 25 MHz Taitien XTAL; jitter integration bandwidth =

12 kHz to 5 MHz

100 MHz Output

400 MHz Output

Source = PLL1; Qx divider = 8; jitter integration bandwidth =

12 kHz to 20 MHz

1.617

Source = PLL1; Qx divider = 2; jitter integration bandwidth =

12 kHz to 20 MHz

LVDS INTEGRATED RMS JITTER

25 MHz Output

0.535

1.535

1.605

ps

Source = 25 MHz Taitien XTAL; jitter integration bandwidth =

12 kHz to 5 MHz

100 MHz Output

400 MHz Output

Source = PLL1; Qx divider = 8; jitter integration bandwidth =

12 kHz to 20 MHz

Source = PLL1; Qx divider = 2; jitter integration bandwidth =

12 kHz to 20 MHz

2.5 V CMOS INTEGRATED RMS JITTER

25 MHz Output

0.17

ps

Source = 25 MHz Taitien XTAL; jitter integration bandwidth =

12 kHz to 5 MHz

100 MHz Output

400 MHz Output

1.669

1.586

Source = PLL1; Qx divider = 8; jitter integration bandwidth =

12 kHz to 20 MHz

Source = PLL1; Qx divider = 2; jitter integration bandwidth =

12 kHz to 20 MHz

OUT8 TO OUT10 CHANNEL CYCLE TO CYCLE CLOCK JITTER SPECIFICATIONS

Frequency multiplier (×2) at PLL input enabled. Cycle to cycle jitter magnitude varies with respect to the clock edge (rising or falling).

Table 12 indicates jitter for the worst edge (rising or falling). The better edge typically offers a factor of 2 improvement over the tabulated jitter.

Table 12.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

LVDS CYCLE TO CYCLE JITTER

66.6 MHz Output

Peak-to-peak jitter, 10,000 cycles

43.9

30.3

ps

133.3 MHz Output

1.8 V CMOS CYCLE TO CYCLE JITTER

66.6 MHz Output

Peak-to-peak jitter, 10,000 cycles

35.3

27.4

ps

133.3 MHz Output

3.3 V CMOS CYCLE TO CYCLE JITTER

33.3 MHz Output

83

ps

66.6 MHz Output

44.9

65.4

133.3 MHz Output

Rev. A | Page 13 of 65

AD9576

Data Sheet

LOGIC INPUT PINS CHARACTERISTICS—REF_SEL, RESET, SPx, PPRx

Table 13.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

INPUT STATIC CHARACTERISTICS

REF_SEL Pin

Internal 30 kΩ pull-down resistor

Logic 1 Voltage (V_IH)

Logic 0 Voltage (V_IL)

Logic 1 Current (I_IH)

2.11

V

1.0

V

195

µA

V_IH= V_{DD_x}; value represents the magnitude

of current draw

Logic 0 Current (I_IL)

0.25

µA

V_IL= GND; value represents the magnitude

of current draw

RESET Pin

Internal 30 kΩ pull-up resistor

Logic 1 Voltage (V_IH)

Logic 0 Voltage (V_IL)

Logic 1 Current (I_IH)

1.9

V

0.9

V

0.04

µA

V_IH= V_{DD_x}; value represents the magnitude

of current draw

Logic 0 Current (I_IL)

260

µA

V_IL= GND; value represents the magnitude

of current draw

SPx Pins

Logic 1 Voltage (V_IH)

Logic 0 Voltage (V_IL)

Logic 1 Current (I_IH)

V_{DD_x}− 0.5

V

0.28

95

V

µA

V_IH= V_{DD_x}; value represents the magnitude

of current draw

Logic 0 Current (I_IL)

0.04

µA

V_IL= GND; value represents the magnitude

of current draw

RESET TIMING

Pule Width Low

1.25

ns

RESET Inactive to Start of

Register Programming

PPR0 TO PPR3 PINS EXTERNAL

TERMINATION

Maximum resistor tolerance = 10%

State 0

State 1

State 2

State 3

State 4

State 5

State 6

State 7

820

Ω

Pull-down to GND

Pull-up to V_{DD_x}

1800

3900

8200

820

1800

3900

8200

Pull-up to V_{DD_x}

STATUS OUTPUT PINS CHARACTERISTICS—LD_0, LD_1, REF_SW, REF_STATUS, REF_ACT

Table 14.

Parameter

Min

Typ

Max

Unit

Test Conditions/Comments

OUTPUT CHARACTERISTICS

Logic 1 Voltage

I_LOAD= 1 mA (source or sink)

V_{DD_x}− 0.1

V

Logic 0 Voltage

0.03

Rev. A | Page 14 of 65

Data Sheet

AD9576

SERIAL CONTROL PORT SPECIFICATIONS

Serial Port Interface (SPI) Mode

Table 15.

Parameter

CS (INPUT)

Input Voltage

Logic 1

Symbol

Min

Typ

Max

Unit

Test Conditions/Comments

Input pin

V_{DD_x}− 0.3

V

Logic 0

0.71

Input Current

Logic 1

−0.2

−0.3

2

nA

pF

Logic 0

Input Capacitance

SCLK (INPUT) IN SPI MODE

Input Voltage

Logic 1

V_{DD_x}− 0.3

V_{DD_x}− 0.1

V

Logic 0

0.71

Input Current

Logic 1

−0.7

−0.6

2

nA

pF

Logic 0

Input Capacitance

SDIO (INPUT)

Input Voltage

Logic 1

Pin is bidirectional

V

Logic 0

0.71

Input Current

Logic 1

0.7

−0.8

2

nA

pF

Logic 0

Input Capacitance

SDIO (OUTPUT)

Output Voltage

Logic 1

Pin is bidirectional

V

Logic 0

0.05

50

TIMING

Clock Rate (SCLK, 1/t_SCLK

Pulse Width High

)

MHz

ns

t_HIGH

t_LOW

t_DS

4

Pulse Width Low

2.2

2.5

2.7

ns

SDIO to SCLK Setup

SCLK to SDIO Hold

ns

t_DH

t_DV

t_S

ns

SCLK to Valid SDIO and SDO

CS to SCLK Setup

6.44

ns

0

ns

CS to SCLK Hold

t_C

0

ns

CS Minimum Pulse Width High

t_PWH

2.7

ns

Rev. A | Page 15 of 65

AD9576

Data Sheet

I²C Mode

Table 16.

Parameter

Symbol Min

0.7 × V_{DD_x}

Typ Max

Unit

Test Conditions/Comments

SDA, SCL VOLTAGE

Input Logic 1

Input Logic 0

Input Current

When inputting data

V

0.3 × V_{DD_x}

V

−10

+10

µA

Input voltage between 0.1 × V_{DD_x}and

0.9 × V_{DD_x}

Hysteresis of Schmitt Trigger Inputs

SDA

0.015 × V_{DD_x}

V

When outputting data

Output Logic 0 Voltage at 3 mA Sink

Current

0.2

V

1

Output Fall Time from VIH_MINto VIL_MAX

TIMING

20 + 0.1 C_B

250

ns

Bus capacitance from 10 pF to 400 pF

All I²C timing values are referred to VIH_MIN

(0.3 × V_DD) and VIL_MAXlevels (0.7 × V_DD)

Clock Rate (SCL, f_I2C)

400

kHz

µs

Bus Free Time Between a Stop and

Start Condition

t_BUF

1.3

0.6

Setup Time for a Repeated Start

Condition

t_{SU; STA}

µs

Hold Time (Repeated) Start Condition t_{HD; STA}

After this period, the first clock pulse is

generated

Setup Time for a Stop Condition

Low Period of the SCL Clock

High Period of the SCL Clock

SCL, SDA Rise Time

t_{SU; STO}

t_LOW

t_HIGH

t_R

0.6

1.3

0.6

µs

ns

pF

1

20 + 0.1 C_B

300

1

SCL, SDA Fall Time

t_F

20 + 0.1 C_B

Data Setup Time

t_{SU; DAT}

100

0

Data Hold Time

t_{HD; DAT}

1

Capacitive Load for Each Bus Line

C_B

400

¹C_Bis the capacitance of one bus line in picofarads (pF).

Rev. A | Page 16 of 65

Data Sheet

AD9576

ABSOLUTE MAXIMUM RATINGS

Table 17.

THERMAL RESISTANCE

Thermal performance is directly linked to printed circuit board

(PCB) design and operating environment. Careful attention to

PCB thermal design is required.

Parameter

Rating

V_{DD_x}to GND

Junction Temperature¹

−0.3 V to +3.6 V

150°C

Storage Temperature Range

−65°C to +150°C

Table 18. Thermal Resistance

¹See Table 18 for θ_JA.

Package Type

θ_JA

Unit

Stresses at or above those listed under Absolute Maximum

Ratings may cause permanent damage to the product. This is a

stress rating only; functional operation of the product at these

or any other conditions above those indicated in the operational

section of this specification is not implied. Operation beyond

the maximum operating conditions for extended periods may

affect product reliability.

CP-64-17¹

22.7

°C/W

¹Thermal impedance is based on a 4-layer board in still air in accordance with

a JEDEC JESD51-7 plus JEDEC JESD51-5 2S2P test board and in accordance with

JEDEC JESD51-2 (still air).

ESD CAUTION

Rev. A | Page 17 of 65

AD9576

Data Sheet

PIN CONFIGURATION AND FUNCTION DESCRIPTIONS

48 OUT0

REF2

1

2

3

4

5

6

7

8

9

47 OUT0

46 VDD_OUT01

45 OUT1

44 OUT1

43 OUT2

42 OUT2

41 VDD_OUT23

40 OUT3

REF_SEL

VDD_REFMON

REF_ACT

REF_SW

REF0

AD9576

REF0

VDD_REF0

TOP VIEW

(Not to Scale)

39 OUT3

38 GND

VDD_REF1 10

REF1 11

REF1 12

37 OUT4

CS 13

36 OUT4

SCLK/SCL 14

SDIO/SDA 15

VDD_IO 16

35 VDD_OUT45

34 OUT5

33 OUT5

NOTES

1. THE EXPOSED PAD IS A GROUND CONNECTION ON THE CHIP THAT

MUST BE SOLDERED TO THE ANALOG GROUND OF THE PCB TO

ENSURE PROPER FUNCTIONALITY, HEAT DISSIPATION, NOISE,

AND MECHANICAL STRENGTH BENEFITS.

Figure 4. Pin Configuration

Table 19. Pin Function Descriptions

Input/

Pin No.

Mnemonic

Output Pin Type

Description

1

REF2

Input

Configurable

clock input

Complimentary Reference Clock Input 2. This pin is the complimentary

signal to the input on Pin 2 (REF2). When REF2 is configured as 2.5 V/3.3 V,

dc-coupled, single-ended LVCMOS, leave this pin floating. When REF2 is

configured as 1.8 V, ac-coupled, single-ended LVCMOS, this pin must be ac

grounded via a 100 nF capacitor.

2

3

REF2

Input

Configurable

clock input

Reference Clock Input 2. This clock can serve as the stable clock input to the

reference monitor, as well as an input to PLL1. Its format can be configured

as 2.5 V/3.3 V, dc-coupled, single-ended LVCMOS, or 1.8 V, ac-coupled, single-

ended LVCMOS, differential input (with a complimentary signal on REF2,

Pin 1, or as an XTAL input. The receiver format is power-on configurable via

PPR0 (Pin 24) and is independently configurable via the serial port.

REF_SEL

Input

2.5 V/3.3 V CMOS

control

Reference Clock Select. This pin selects the output clock of the reference

selection mux, which can be either Reference Clock Input 0 or Reference Clock

Input 1 (Logic 0 or Logic 1, respectively). For this pin to function, automatic

reference switching and soft REF_SEL must be disabled (Register 0x082,

Bits[2:1] = 00). This pin has an internal 30 kΩ pull-down resistor.

4

5

VDD_REFMON

REF_ACT

Power

2.5 V or 3.3 V Power Supply.

Output 2.5 V/3.3 V CMOS

Currently Selected, Active Reference Indicator. This status signal represents

the output of the reference selector mux. Logic 0 means that REF0 is the

currently selected reference, Logic 1 means that REF1 is the currently

selected reference. This pin is on the VDD_REFMON power domain.

6

REF_SW

Output 2.5 V/3.3 V CMOS

Reference Switchover Status Indicator. Logic 0 = normal operation, Logic 1

means reference switch in progress. This pin is on the VDD_REFMON power

domain.

Rev. A | Page 18 of 65

Data Sheet

AD9576

Input/

Pin No.

Mnemonic

Output Pin Type

Description

7

REF0

Input

Configurable

clock input

Reference Clock Input 0. This clock is an input to the reference selection

mux. The clock format can be configured as 2.5 V/3.3 V, dc-coupled, single-

ended LVCMOS, or 1.8 V, ac-coupled, single-ended LVCMOS, differential

input (with a complimentary signal on REF0, Pin 8), or as an XTAL input. The

receiver format is power-on configurable via PPR0 (Pin 24) and is independently

configurable via the serial port.

8

REF0

Input

Configurable

clock input

Complimentary Reference Clock Input 0. Complimentary signal to the input

on Pin 7 (REF0). When REF0 is configured as 2.5 V/3.3 V, dc-coupled, single-

ended LVCMOS, leave this pin floating. When REF0 is configured as 1.8 V,

ac-coupled, single-ended LVCMOS, this pin must be ac grounded via a

100 nF capacitor.

9

VDD_REF0

VDD_REF1

REF1

Input

Power

2.5 V or 3.3 V Power Supply. Configure this supply to set the full swing

CMOS logic high level of Reference Input 0, REF0.

10

11

2.5 V or 3.3 V Power Supply. Configure this supply to set the full swing

CMOS logic high level of Reference Input 1, REF1.

Configurable

clock input

Complimentary Reference Clock Input 1. Complimentary signal to the input

on Pin 12 (REF1). When REF1 is configured as 2.5 V/3.3 V, dc-coupled, single-

ended LVCMOS, leave this pin floating. When REF1 is configured as 1.8 V,

ac-coupled, single-ended LVCMOS, this pin must be ac grounded via a

100 nF capacitor.

12

REF1

Input

Configurable

clock output

Reference Clock Input 1. This clock is an input to the reference selection

mux. The clock format can be configured as 2.5 V/3.3 V, dc-coupled, single-

ended LVCMOS, or 1.8 V, ac-coupled, single-ended LVCMOS, differential

input (with a complimentary signal on REF1, Pin 11), or as an XTAL input.

The receiver format is power-on configurable via PPR0 (Pin 24) and is

independently configurable via the serial port.

13

14

CS

Input

2.5 V/3.3 V CMOS

Chip Select for SPI Serial Communication (Active Low Input). When

programming the device in SPI mode, this pin must be held low, as shown

in Figure 32. The logic high level of this pin is determined by VDD_IO.

Serial Control Port Clock Signal for SPI Mode (SCLK) or I²C Mode (SCL). This

pin is the data clock for serial programming. The logic high level of this pin

is determined by the VDD_IO pin.

SCLK/SCL

15

16

SDIO/SDA

VDD_IO

Input/

output

2.5 V/3.3 V CMOS

Power

Serial Control Port Bidirectional Serial Data In/Data Out for SPI Mode (SDIO)

or I²C Mode (SDA). The logic high level of this pin is determined by V_{DD_IO}

.

Input

2.5 V or 3.3 V Power Supply. Configure this pin to set the logic high level of

the serial port interface.

17

LD_0

Output 2.5 V/3.3 V CMOS

PLL0 Lock Detector Status. Logic 0 means unlocked; Logic 1 means locked.

2.5 V or 3.3 V Power Supply.

18

VDD_PLL0

LF

Input

Power

Analog

Power

Control

19

Loop Filter. Connect a 4.7 nF capacitor from this pin to LDO_BYP (Pin 20).

LDO Bypass. Connect a 470 nF capacitor from this pin to ground.

2.5 V or 3.3 V Power Supply.

20

LDO_BYP

VDD_VCO0

SP1, SP0

21

22, 49

Input/

Serial Port Configuration Pins. These pins are latched at power-up and upon

release from reset to configure the serial port as well as to determine

whether a PPR load is to occur. See Table 35 for a complete decode of

configurations. These pins use three-state logic: high, low, and floating.

output

23

24

VDD_M0

PPR0

Input

Power

2.5 V or 3.3 V Power Supply.

Control

Pin Program Reader 0. Connect a resistor to this pin to configure the

reference clock input formats and the PLL1 input source.

25

26

VDD_M1

PPR1

Input

Power

2.5 V or 3.3 V Power Supply.

Control

Pin Program Reader 1. Connect a resistor to this pin to configure the OUT10

frequency, input source, and logic format.

27

28

OUT7

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 7. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 7. This pin is the complimentary signal to the

output on Pin 27 (OUT7).

29

30

VDD_OUT67

OUT6

Input

Power

2.5 V or 3.3 V Power Supply.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 6. This pin is the complimentary signal to the

output on Pin 31 (OUT6).

Rev. A | Page 19 of 65

AD9576

Data Sheet

Input/

Pin No.

Mnemonic

Output Pin Type

Description

31

OUT6

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 6. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

32, 56

33

PPR2, PPR3

OUT5

Input

Control

Pin Program Reader 2 and Pin Program Reader 3. Connect a resistor to

these pins to configure the REF0/REF1 input frequency and OUT0 to OUT9.

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 5. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

34

OUT5

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 5. This pin is the complimentary signal to the

output on Pin 33 (OUT5).

35

36

VDD_OUT45

OUT4

Input

Power

2.5 V or 3.3 V Power Supply.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 4. This pin is the complimentary signal to the

output on Pin 37 (OUT4).

37

OUT4

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 4. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

38

39

GND

Input

Ground

Power Supply Common Ground.

OUT3

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 3. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

40

OUT3

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 3. This pin is the complimentary signal to the

output on Pin 39 (OUT3).

41

42

VDD_OUT23

OUT2

Input

Power

2.5 V or 3.3 V Power Supply.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 2. This pin is the complimentary signal to the

output on Pin 43 (OUT2).

43

44

45

OUT2

OUT1

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 2. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 1. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 1. This pin is the complimentary signal to the

output on Pin 44 (OUT1).

46

47

VDD_OUT01

OUT0

Input

Power

2.5 V or 3.3 V Power Supply.

Output HSTL, LVDS, 1.8 V

CMOS

Complimentary Clock Output 0. This pin is the complimentary signal to the

output on Pin 48 (OUT0).

48

50

OUT0

OUT8

Output HSTL, LVDS, 1.8 V

CMOS

Clock Output 0. The power-on format is determined via PPR2 (Pin 32) and

PPR3 (Pin 56). This pin is independently configurable via the serial port.

Output 2.5 V/3.3 V CMOS,

Clock Output 8. When configured as 2.5 V/3.3 V CMOS, the logic high level

1.8 V CMOS, HSTL, is determined by VDD_OUT89. The power-on format is determined via

LVDS, HCSL

PPR2 (Pin 32) and PPR3 (Pin 56). This pin is independently configurable via

the serial port.

51

OUT8

Output 2.5 V/3.3 V CMOS,

Complimentary Clock Output 8. This pin is the complimentary signal to the

1.8 V CMOS, HSTL, output on Pin 50 (OUT8).

LVDS, HCSL

52

53

VDD_OUT89

OUT9

Input

Power

2.5 V or 3.3 V Power Supply. Configure this supply to set the full swing

CMOS logic high level of Output 8 and Output 9.

Output 2.5 V/3.3 V CMOS,

Complimentary Clock Output 9. This pin is the complimentary signal to the

1.8 V CMOS, HSTL, output on Pin 54 (OUT9).

LVDS, HCSL

54

55

OUT9

Output 2.5 V/3.3 V CMOS,

Clock Output 9. When configured as 2.5 V/3.3 V CMOS, the logic high level

1.8 V CMOS, HSTL, is determined by VDD_OUT89. The power-on format is determined via

LVDS, HCSL

PPR2 (Pin 32) and PPR3 (Pin 56). This pin is independently configurable via

the serial port.

REF_STATUS

Output 2.5 V/3.3 V CMOS

Reference Status Indicator. When the reference monitor is enabled, this pin

indicates if the output of the reference selection mux is determined to be

within the configured tolerance setting. Logic 0 means the reference is within

tolerance; Logic 1 means the reference is outside of tolerance. When the

reference monitor is disabled, this pin indicates the loss of reference (LOR)

status for the requested reference.

57

VDD_OUT10

Input

Power

2.5 V or 3.3 V Power Supply. Configure this supply to set the full swing

CMOS logic high level of Output 10. This pin also serves as the PPRx power

supply.

Rev. A | Page 20 of 65

Data Sheet

AD9576

Input/

Pin No.

Mnemonic

Output Pin Type

Description

58

OUT10

Output

2.5 V/3.3 V CMOS,

1.8 V CMOS, HSTL,

LVDS, HCSL

Clock Output 10. When configured as 2.5 V/3.3 V CMOS, the logic high level is

determined by VDD_OUT10. The power-on format is determined via PPR1

(Pin 26). This pin is independently configurable via the serial port.

59

OUT10

Output 2.5 V/3.3 V CMOS,

Complimentary Clock Output 10. This pin is the complimentary signal to

1.8 V CMOS, HSTL, the output on Pin 58 (OUT10).

LVDS, HCSL

60

61

62

63

VDD_VCO1

VDD_PLL1

LD_1

Input

Power

2.5 V or 3.3 V Power Supply.

Power

2.5 V or 3.3 V Power Supply.

Output 2.5 V/3.3 V CMOS

PLL1 Lock Detector Status. Logic 0 means unlocked; Logic 1 means locked.

RESET

Input

Control

Reset. Logic 0 initializes the device to its default state (see the PPRx Pins

section for details). This pin has an internal 30 kΩ pull-up resistor.

64

VDD_REF2

EPAD

Power

2.5 V or 3.3 V Power Supply. Configure this supply to set the full swing

CMOS logic high level of Reference Input 2, REF2.

Ground

Exposed Pad. The exposed pad is a ground connection on the chip that

must be soldered to the analog ground of the PCB to ensure proper

functionality, heat dissipation, noise, and mechanical strength benefits.

Rev. A | Page 21 of 65

AD9576

Data Sheet

TYPICAL PERFORMANCE CHARACTERISTICS

PHASE NOISE AND VOLTAGE WAVEFORMS

V_{DD_x}= nominal, T_A= 25°C. The only enabled output channels are those indicated in the figure captions. The phase noise plots (see Figure 5 to

Figure 9) show the Taitien XO A0145-L-006-3 (noted as XO in the figures) phase noise normalized to the output frequency. The voltage

waveform plots (see Figure 10 to Figure 16) embody ac coupling to the measurement instrument.

AD9576

XO

AD9576

XO

100

1k

10k

100k

1M

10M

100M

100

1k

10k

100k

1M

10M

FREQUENCY OFFSET (Hz)

Figure 5. Phase Noise (OUT0)—f_OUT0= 644.53125 MHz (HSTL), Fractional

Figure 8. Phase Noise (OUT2)—f_OUT2= 156.25 MHz (HSTL)

AD9576

XO

AD9576

XO

100

1k

10k

100k

1M

10M

100

1k

10k

100k

1M

10M

FREQUENCY OFFSET (Hz)

Figure 6. Phase Noise (OUT3)—f_OUT3= 100 MHz (HSTL), f_OUT4= 125 MHz (HSTL)

Figure 9. Phase Noise (OUT3)—f_OUT3= 125 MHz (HSTL), f_OUT4= 100 MHz (HSTL)

156.25MHz

312.5MHz

AD9576

XO

100

1k

10k

100k

1M

10M

0

5

10

15

20

25

FREQUENCY OFFSET (Hz)

TIME (ns)

Figure 7. Phase Noise (OUT4)—f_OUT4= 312.5 MHz (LVDS)

Figure 10. OUT0 Output Waveform, HSTL (156.25 MHz, 312.5 MHz)

Rev. A | Page 22 of 65

Data Sheet

AD9576

100MHz

400MHz

0

5

10

15

20

25

0

5

10

15

20

25

30

35

40

TIME (ns)

Figure 11. OUT8 Output Waveform, HCSL (100 MHz, 400 MHz)

Figure 14. OUT0 Output Waveform, LVDS ( 312.5 MHz)

0

10

20

30

40

50

60

0

20

40

60

80

100

120

140

160

TIME (ns)

Figure 12. OUT8 Output Waveform, 1.8 V CMOS (66.67 MHz), 10 pF Load

Figure 15. OUT8 Output Waveform, 3.3 V CMOS (25 MHz), 10 pF Load

0

5

10

15

20

25

30

0

5

10

15

20

25

30

TIME (ns)

Figure 13. OUT8 Output Waveform, LVDS (133.3 MHz)

Figure 16. OUT8 Output Waveform, 3.3 V CMOS (133.3 MHz), 10 pF Load

Rev. A | Page 23 of 65

AD9576

Data Sheet

REFERENCE SWITCHING FREQUENCY AND PHASE DISTURBANCE

V_{DD_x}= nominal, T_A= 25°C. The only enabled output channels are those indicated in the figure captions. The reference switchover phase

disturbance plots, Figure 17, Figure 18, and Figure 19, each show a collection of output phase variations due to approximately 250 reference

switching events between two references with a frequency offset of approximately 2 ppm. Each reference switch event (initiated by

toggling the REF_SEL pin) occurs at a random phase offset between the two references. The plots demonstrate the tightly controlled

phase disturbance at the output as a result of the reference switching logic seeking the optimal moment to switch references.

0

1

2

3

4

5

6

0

1

2

3

4

5

6

TIME (μs)

Figure 19. Reference Smooth Switchover Phase Disturbance for OUT8 at

25 MHz (PPR0 = 3, PPR1 = 0, PPR2 = 0, PPR3 = 3)

Figure 17. Reference Smooth Switchover Frequency Disturbance for OUT0 at

156.25 MHz (PPR0 = 3, PPR1 = 0, PPR2 = 0, PPR3 = 3)

9.0

6.5

4.0

1.5

–1.0

–3.5

–6.0

0

1

2

3

4

5

6

TIME (μs)

Figure 18. Reference Smooth Switchover Phase Disturbance for OUT0 at

156.25 MHz (PPR0 = 3, PPR1 = 0, PPR2 = 0, PPR3 = 3)

Rev. A | Page 24 of 65

Data Sheet

AD9576

TERMINOLOGY

Phase Jitter

Time Jitter

An ideal sine wave has a continuous and even progression of

phase with time from 0° to 360° for each cycle. Actual signals,

however, display a certain amount of variation from ideal phase

progression over time. This phenomenon is called phase jitter.

Although many causes can contribute to phase jitter, one major

cause is random noise, which is character-ized statistically as

Gaussian (normal) in distribution.

Phase noise is a frequency domain phenomenon. In the time

domain, the same effect is exhibited as time jitter. When observing

a sine wave, the time of successive zero crossings is seen to vary.

In a square wave, the time jitter is seen as a displacement of the

edges from their ideal (regular) times of occurrence. In both

cases, the variations in timing from the ideal are the time jitter.

Because these variations are random in nature, the time jitter is

specified in units of seconds root mean square (rms) or 1 Σ of the

Gaussian distribution.

This phase jitter leads to the energy of the sine wave spreading

out in the frequency domain, producing a continuous power

spectrum. This power spectrum is usually reported as a series of

values whose units are dBc/Hz at a given offset in frequency from

the sine wave (carrier). The value is a ratio (expressed in dB) of

the power contained within a 1 Hz bandwidth with respect to

the power at the carrier frequency. For each measurement, the

offset from the carrier frequency is also given.

Additive Phase Noise

Additive phase noise is the amount of phase noise that is

attributable to the device or subsystem being measured. The

phase noise of any external oscillators or clock sources is sub-

tracted, which makes it possible to predict the degree to which

the device impacts the total system phase noise when used in

conjunction with the various oscillators and clock sources, each

of which contributes its own phase noise to the total. In many

cases, the phase noise of one element dominates the system

phase noise.

Phase Noise

When the total power contained within some interval of offset

frequencies (for example, 12 kHz to 20 MHz) is integrated, it is

called the integrated phase noise over that frequency offset interval,

and it can be readily related to the time jitter due to the phase

noise within that offset frequency interval.

Additive Time Jitter

Additive time jitter is the amount of time jitter that is attributable

to the device or subsystem being measured. The time jitter of

any external oscillators or clock sources is subtracted, which

makes it possible to predict the degree to which the device

impacts the total system time jitter when used in conjunction

with the various oscillators and clock sources, each of which

contributes its own time jitter to the total. In many cases, the

time jitter of the external oscillators and clock sources dominates

the system time jitter.

Phase noise has a detrimental effect on error rate performance

by increasing eye closure at the transmitter output and reducing

the jitter tolerance/sensitivity of the receiver.

Rev. A | Page 25 of 65

AD9576

Data Sheet

THEORY OF OPERATION

1.8V CMOS

2.5V/3.3V CMOS

HCSL

AD9576

10

÷Q4

÷Q3

LVDS

HSTL

1.8V CMOS

2.5V/3.3V CMOS

HCSL

LVDS

HSTL

9

8

÷N1

×2

CHARGE

PUMP

VCO1

LPF

REF2

÷R1

0

PLL1

INTEGER-N

1

2

3

1.8V CMOS

LVDS

HSTL

REF_STATUS

÷Q0

REF0/REF1

MONITOR

PLL0

FRACTIONAL-N

÷Q

ZD

÷N0A

REF_SEL

REF_ACT

REF_SW

REF0/REF1

SWITCHOVER

÷N0

4

5

÷M0

1.8V CMOS

LVDS

÷Q0

÷Q1

REF0

REF1

HSTL

×2

CHARGE

PUMP

VCO0

LPF

÷M1

÷R0

6

7

1.8V CMOS

LVDS

HSTL

CONTROL

INTERFACE

PPRx LOGIC

2

(I C/SPI)

Figure 20. Detailed Functional Block Diagram

The AD9576 provides up to 11 output channel clocks (OUT0 to

OUT10). OUT0 to OUT7 are driven by PLL0 exclusively and

are comprised of three subgroups of outputs (OUT0 to OUT3,

OUT4 and OUT5, and OUT6 and OUT7). Each output within a

subgroup is individually configurable, but generates the same

output frequency. These outputs support LVDS, HSTL, or 1.8 V

LVCMOS output formats.

OVERVIEW

Figure 20 shows a block diagram of the AD9576. The AD9576

is a 2.5 V or 3.3 V single-supply, pin programmable, power-on

ready, dual-channel clock that is fully configurable via a serial

port interface (SPI). The two parallel channels consist of a high

performance, fractional-N PLL (PLL0) and a general-purpose,

integer-N PLL (PLL1).

OUT8 and OUT9 have three potential sources: the output of the

PLL1 reference selection mux directly, the output of PLL0, or

the output of PLL1. These outputs are individually configurable,

but must share the same source and, therefore, the same output

frequency. OUT10 is driven by either the output of the PLL1

reference selection mux directly or the output of PLL1. These

three outputs support LVDS, HSTL, HCSL, 1.8 V CMOS, and

2.5 V/3.3 V CMOS (the swing is determined by the supply

level) output formats.

There are a total of three reference inputs (REF0 to REF2) on

the AD9576. Each input receiver provides differential or single-

ended input configurations. REF0 and REF1 drive the reference

switchover multiplexer (mux). The output of this reference switch-

over mux drives the input of PLL0 and an input to the PLL1

reference selection mux. REF2 drives the alternate input of the

PLL1 reference selection mux and serves as monitor clock to

the on-board reference monitor, which monitors the reference

switchover mux output clock frequency. REF2 supports frequencies

of 8 kHz, 10 MHz, 19.44 MHz, 25 MHz, and 38.88 MHz, while

REF0 and REF1 support 8 kHz, 1.544 MHz, 2.048 MHz, and

10 MHz to 325 MHz. However, the PLL1 phase and PFD input

rate is limited to 25 MHz or 50 MHz, so only a subset of allowable

reference input frequencies are valid for use as an input to PLL1.

REFERENCE INPUTS

The AD9576 features a flexible PLL reference input circuit

that provides three operating modes: single-ended input, fully

differential input, or external crystal input. The operating

mode of the REF0, REF1, and REF2 input receivers are

selected and controlled by the scanned state of the PPR0 pin

or by Register 0x080 and Register 0x081 (see Table 45).

Register 0x080 and Register 0x081 allow fully independent

control of the operating mode selection for each reference input.

Rev. A | Page 26 of 65

Data Sheet

AD9576

In single-ended CMOS buffer mode, a 2.5 V or 3.3 V clock

source is connected directly to the positive reference input pin

(for example, REF0). Note that, in single-ended mode, it is best

to connect a 0.1 µF capacitor from the negative input pin (for

bits (Register 0x021, Bits[5:4]) and the REF_STATUS pin. To

enable the reference monitor, the user must set the enable reference

monitor bit (Register 0x083, Bit 7) to Logic 1. Note that the

frequency accuracy of the inactive reference channel is not

monitored.

REF0

example,

) to GND. The CMOS swing of the reference

input is dependent on V_{DD_x}of said reference input supply and

does not exceed V_{DD_x}. The single-ended CMOS receivers are

powered down when their individual power-down bits are set in

Register 0x080 and Register 0x081, or when operating in

differential or external crystal input mode.

Table 20. Reference Monitor Error Window

Frequency Error

Threshold (ppm)

Register 0x083, Bits[1:0] Value

10

00

01

10

11

25

In differential mode, a differential clock driver is connected to

50

REF0

the two reference input pins (for example, REF0 and

).

100

Note that, in differential operating mode, the reference input

pins are internally self biased to allow ac coupling. That is, a

0.1 µF capacitor is connected in series from each output of the

external differential clock driver to the corresponding reference

input pin. This mode also supports a single-ended, 1.8 V CMOS

clock source by connecting the source to the positive reference

input pins (for example, REF0) with the negative reference

Reference monitoring is only supported for two input frequencies,

19.44 MHz and 25 MHz. The user must specify which frequency is

to be monitored by configuring the monitored frequency bit

(Register 0x083, Bit 5). A Logic 0 value indicates that the PLL0

input frequency is 25 MHz, whereas a Logic 1 indicates a frequency

of 19.44 MHz. The reference monitor frequency reference, REF2,

can be one of five frequencies selectable via two bit fields, as

shown in Table 21.

REF0

input pin (for example,

) connected to GND via a 0.1 µF

capacitor. The differential input receivers are powered down

when their individual power-down bits are set in Register 0x080

and Register 0x081, or when operating in single-ended CMOS

or external crystal input mode.

Table 21. REF2 Monitor Frequency Decode

Register 0x083, Register 0x083,

REF2 Input Frequency

8 kHz

Bit 4 Value

Bits[3:2] Value

1

0

Not applicable

External crystal mode is comparable to differential mode,

except a fundamental mode AT cut crystal is connected across

10 MHz

00

01

10

11

19.44 MHz

25 MHz

REF0

the two reference input pins (REF0 and

, for example) and

is powered by an internal maintaining amplifier. The external

crystal receivers are powered down via the individual power down

bits in Register 0x080 and Register 0x081, or when operating in

single-ended or differential input mode. The REF0 and REF1

external crystal receivers are also powered down if they are not

the currently active/requested reference clock for PLL0.

38.88 MHz

After comparing the calculated input frequency ppm error to

the user specified threshold window, the resulting frequency

accuracy is reported on the reference status bits (Register 0x021.

Bits[5:4]) and on the REF_STATUS pin. The values of the reference

status bits and the respective significance are listed in Table 22.

The status indicated on the REF_STATUS pin is the logical OR

of the reference status bits.

The reference input format bits, REF0 format (Register 0x080,

Bits[1:0]), REF1 format (Register 0x080, Bits[5:4]), and REF2

format (Register 0x081, Bits[1:0]) must be set correctly for the

applied input. These bits are set to 00 for 2.5 V and 3.3 V CMOS

inputs, 01 for differential inputs and 1.8 V CMOS inputs, and

10 for XTAL inputs. Setting the reference input format bits

incorrectly for the applied input may cause undesired results. The

input frequency range for the reference inputs is specified in

Table 4.

Table 22. Reference Frequency Monitor Status Decode

Frequency Status

Register 0x021, Bits[5:4] Value

Valid

00

01

10

11

Slow

Fast

Indeterminate Fault

REFERENCE MONITOR

The REF_STATUS pin similarly reports whether the frequency

of the active input is within the user specified threshold window. A

Logic 0 on this pin indicates the selected input reference frequency

is within the tolerance threshold specified by the user, whereas a

Logic 1 indicates the selected input reference frequency is outside

the tolerance threshold specified by the user. Note that the

REF_STATUS pin only specifies whether the selected input

reference frequency is within the user specified tolerance threshold.

If more detailed information regarding the manifestation of the

error is required, refer to the reference status bits.

The AD9576 reference monitor function provides the user a

means to validate the frequency accuracy of the PLL0 active

reference (REF0 or REF1) in real time. When enabled, the

reference monitor uses REF2 as the frequency reference to

continuously test the frequency accuracy of the active reference.

The measured frequency error of the PLL0 active input reference is

compared to a user programmable frequency error threshold.

The result is reported as being either within or outside the user

specified threshold (see Table 20) on both the reference status

Rev. A | Page 27 of 65

AD9576

Data Sheet

In addition to the frequency monitoring function, the reference

monitor also checks for the presence of a clock signal at the REF0,

REF1, and REF2 inputs. The absence of a clock signal results in

an internal LOR indication for that particular clock input. A

Logic 1 LOR status indicates that the reference is not present,or

that the frequency is below approximately 1 MHz. A Logic 0 status

indicates that reference input is detected and the frequency is

greater than 1 MHz. When REF2 is configured as an 8 kHz

reference to be used with the reference monitor, the REF2 LOR

circuitry uses the PLL0 active reference to qualify the presence

and accuracy of the REF2 input clock. Table 23 defines the

REF2 LOR conditions for all valid operating modes.

clock is designated by the state of REF_SEL when the enable

XTAL redundancy switchover bit is set to Logic 1.

In manual reference switchover mode, the user manually

changes the input reference by toggling the state of either the

soft reference select bit (Register 0x082, Bit 0) or the REF_SEL pin

(Pin 3). The control method of manual reference switchover is

determined by the state of the enable soft reference select bit

(Register 0x082, Bit 1), as shown in Table 24.

Table 24. PLL0 Active Reference Selection Source Decode

PLL0 Active Reference Selection

Source

Register 0x082, Bit 1

Value

REF_SEL (Pin 3)

0

1

Table 23. REF2 LOR Status Decode

Register 0x082, Bit 0

REF2 Input

Frequency

REF0/REF1

Frequency

Reg. 0x021, REF2 LOR

Bit 2 Value

Condition

>6.1 kHz

< 6.1 kHz

>4.7 kHz

<4.7 kHz

>1 MHz

When the REF_SEL pin controls manual reference switchover, a

logic signal is supplied to the pin to specify the desired input

reference. A Logic 0 on the REF_SEL pin informs the internal

reference switching logic to make REF0 the active reference

input, whereas a Logic 1 makes REF1 the active reference.

When the soft reference select bit controls manual reference

switchover, setting this bit to a Logic 0 selects REF0 as the active

reference input, whereas setting this bit to a Logic 1 selects REF1

as the active input reference. Note that, with manual switching

enabled, the frequency monitoring function of the reference

monitor (see the Reference Monitor section) may still be used,

but it does not trigger a reference switchover for PLL0.

8 kHz

25 MHz

0

1

0

1

0

1

19.44 MHz

10 MHz, 19.44 MHz,

25 MHz, or 38.88 MHz

Not

applicable

<1 MHz

A LOR condition for a given reference is reported on its respective

status bit in Register 0x021 (see Table 43). Furthermore, when

reference frequency monitoring is disabled, the REF_STATUS pin

logic state indicates the LOR status for the PLL0 requested

reference input.

Both manual and XTAL redundancy reference switchover

modes provide the option of using the smooth switchover

function. The smooth switchover function is enabled by setting

the disable smooth switchover bit (Register 0x082, Bit 3) to

Logic 0. The smooth switchover function waits for a minimal

phase offset to occur between the REF0 and REF1 reference

inputs, prior to physically switching to the newly requested

reference. This functionality ensures a minimal frequency and

phase disturbance on the output clocks associated with the PLL

due to a reference switchover event. Correct operation of the

smooth switchover function requires the input references be

asynchronous and that a LOR fault condition does not occur on

either reference input while the switch is being made. When the

smooth switchover function is disabled (Register 0x082, Bit 3 = 1),

the switch to the new active reference is instantaneous and the

frequency disturbance on the output clocks during reference

switchover may increase.

REFERENCE SWITCHING

The AD9576 provides both manual switchover as well as a

single-shot, automatic XTAL redundancy switchover capability.

The reference switchover mode is specified through the enable

XTAL redundancy switchover bit (Register 0x082, Bit 2). By

default, this bit is Logic 0 and manual reference switching is

enabled. Setting this bit to a Logic 1 enables automatic XTAL

redundancy switchover.

Automatic XTAL redundancy switchover mode can only be

used when the following three conditions are met:

•

REF0/REF1 are external crystal inputs (Register 0x080,

Bits[5:4] and Register 0x080, Bits[1:0] are both set to 10).

The reference monitoring function is enabled

(Register 0x083, Bit 7 is set to 1).

The REF_SEL pin is held at a static logic state.

The reference switching logic provides information about

which reference channel is the currently active reference, via the

REF_ACT pin (Pin 5) and the active reference bit (Register 0x021,

Bit 3). The REF_ACT pin and the active reference bit are both

Logic 0 when REF0 is the active reference, and are both Logic 1

when REF1 is the active reference. Additionally, the reference

switching logic indicates when the device is in the process of

performing a smooth reference switchover via the REF_SW pin

(Pin 6). The REF_SW pin assumes a Logic 1 state when REF_SEL

changes states and returns to a Logic 0 state when the device

The XTAL redundancy switchover is a single use operation per

device reset, switching from the initial input reference (for example,

REF0) to the alternate input reference (for example, REF1). When

the reference monitor determines the selected input frequency

accuracy is outside of the specified error window, the alternate

input is automatically selected as the new active reference input.

Upon completion of the automatic XTAL redundancy switchover,

the newly selected alternate reference (for example, REF1)

continues to be the input reference source for PLL0, regardless

of the accuracy of the frequency. The initial input reference

Rev. A | Page 28 of 65

Data Sheet

AD9576

completes the reference switchover process. In manual smooth

reference switchover mode, confirm that the device has completed

the requested switch to the desired reference (REF_SW pin =

Logic 0) before initiating a subsequent change of reference request.

Changing the state of the REF_SEL pin or the soft reference

select bit before the internal state machine completes the previous

smooth reference switching process does not result in a

subsequent reference switch.

PLL0 Reference Frequency Scaling

The frequency of the active input reference (REF0 or REF1) is

scalable via the PLL0 doubler enable bit (Register 0x101, Bit 3)

and the R0 divider ratio bits (Register 0x105, Bits[5:0]). This

allows the user to scale the input reference frequency to satisfy

the input range of the PFD. When the PLL0 doubler enable bit

is set to Logic 1, the input frequency to the PFD of PLL0, f_PFD0, is

twice the active reference input frequency. When the PLL0

doubler enable bit is set to Logic 0, f_PFD0is a function of the active

reference frequency scaled by the R0 divider ratio bits.

Because the smooth reference switchover function waits for a

minimal phase offset between references prior to making a

switch, if either of the reference inputs are removed completely

and a switchover request is initiated, the internal smooth

switching state machine stalls and the device is unable to switch

references, thereby retaining the currently active reference. If

the current active reference fails, the device loses lock, thereby

necessitating a device reset. If the requested reference fails, the

device retains the currently active reference, but switches to the

requested reference if it becomes available. Note that, as long as

a reference remains absent, the state machine remains stalled.

Only a device reset makes the state machine disregard the initial

request to switch references.

f_REF

f_PFD0

=

R0

where:

f_REFis the frequency of the active reference, REF0 or REF1.

R0 is the value of the R0 divider ratio bits.

When the PLL0 doubler enable bit is set to Logic 1, the

frequency appearing at the input to the PFD of PLL0, f_PFD0, is

the active reference frequency multiplied by a factor of two.

f_PFD0= f_REF× 2

where f_REFis the frequency of the active reference, REF0 or REF1.

PLL0 INTEGER-N/FRACTIONAL-N PLL

Note that, when the ×2 frequency multiplier is in use, the active

reference signal must have a duty cycle close to 50%. Otherwise,

spurious artifacts (harmonics) may propagate through the

signal path and appear at the output of PLL0.

PLL0 is a fractional-N PLL capable of operating in integer

mode. It consists of seven functional elements: a reference

frequency prescalar, a PFD, a charge pump, a loop filter, a VCO,

feedback dividers, and an optional, third-order, Σ-Δ modulator

(SDM) that allows fractional divide ratios. PLL0 provides two

independent reference clock input signals. The device supports

differential, single-ended, and XTAL operation for both reference

clocks. PLL0 provides 10 outputs, segregated into four groups.

Each group has a dedicated channel divider allowing the device

to produce four different output frequencies simultaneously.

Note that PLL0 is capable of several different loop configurations,

with each described in the following sections. Figure 21 shows

the functional block diagram of PLL0.

PLL0 Loop Configurations

PLL0 is capable of three different loop configurations. Loop 0 is the

fractional translation path, Loop 1 accommodates low frequency

reference inputs, and Loop 2 is a zero delay feedback path. The

PLL0 loop configuration is selected by programming the PLL0

loop mode bits (Register 0x101, Bits[2:1]) as shown in Table 25.

Table 25. PLL0 Loop Configuration Decode

Register 0x101,

Bits[2:1] Value

PLL0 Loop Configuration

Loop 0: Fractional-N/Integer-N

Loop 1: Low PFD Frequency

Loop 2: Zero Delay

00

01

10

11

PLL0

FRAC-N/

INT-N

÷Q

ZD

÷N0A

Reserved

÷N0

÷M0

÷M1

ACTIVE

REF

CHARGE

PUMP

×2

VCO0

÷R0

Figure 21. PLL0 Functional Block Diagram

Rev. A | Page 29 of 65

AD9576

Data Sheet

The resulting values to be used as the operating N0 fraction and

N0 modulus values are as follows:

Loop Configuration 0—Fractional-N/Integer-N

LDO_BYP

LF

N0 fraction = scalar × 73 = 69,042 × 73 = 5,040,066

N0 modulus = scalar × 243 = 69,042 × 243 = 16,777,206

The overall frequency translation equation for Loop 0 is

REF0

REF1

REF.

INPUT

OUT0

OUT9

1.8V

CP

LOOP

÷M0,

M1

VCO

FILTER

REF_SEL

÷N0













N0 fraction

N0 modulus

N0 

SDM

AD9576: PLL0

f

^REF

=

R0

f_OUT

where:

Figure 22. PLL0 Loop Configuration 0

M_ZQ_Y

The Loop 0 configuration is the only configuration that supports a

fractional-N translation in addition to integer-N translations.

This configuration uses a single feedback divider, N0, with an

integrated Σ-Δ modulator.

f_OUTis the frequency at the output driver, OUTx (OUT0 through

OUT9).

f_REFis the frequency of the active reference (REF0 or REF1).

M_Zis the VCO divider (M0 or M1) that is the input source of Q_Y.

Q_Yis the channel divider (Q0, Q1, Q2, or Q3) associated with

OUTx.

The VCO0 frequency is a function of the PFD input frequency

(see the PLL0 Reference Frequency Scaling section) and the

values programmed into the registers associated with N0, N0

fraction, and N0 modulus.

R0 is the divider value used to scale the input reference

frequency and is an element of the following set: {½, 1, 2 … 63}.

Note the value of ½ is the result of selecting the ×2 reference

multiplier (see the PLL0 Reference Frequency Scaling section).









N0 fraction

N0 modulus



f_VCO0 f_PFD0 N0 





where:

N0 is an element of the set: {N_MIN, N_MIN+ 1, …N_MAX} where

N_MIN, N_MAXare 12 and 255, respectively, for integer-N operation

and N_MIN, N_MAXare 15 and 252, respectively, for fractional-N

operation.

f_VCO0is the frequency of the VCO.

f_PFD0is the frequency at the input to the PFD.

N0 is an element of the following set: {N_MIN, N_MIN+ 1, …, 255},

where N_MIN= 12 for integer-N operation and N_MIN= 15 for

fractional-N operation.

N0 fraction is an element of the set: {0, 1, …, 16,777,214}.

N0 modulus is an element of the set: {1, 2, …, 16,777,215} with

the constraint N0 fraction < N0 modulus.

N0 fraction is an element of the following set: {0, 1, …,

16,777,214}.

M_Zis the divide value of the VCO divider and is an element of

the set: {2, 3, …, 11}.

N0 modulus is an element of the following set, but with the

constraint of N0 fraction < N0 modulus: {1, 2, …, 16,777,215}.

Q_Yis the divide value of the channel divider and is an element

of the set: {1, 2, …, 64}.

Programming the N0 SDM power-down bit (Register 0x101, Bit 0)

to Logic 1 disables the SDM, making N0 fraction functionally

equivalent to a value of 0, and PLL0 can only be configured as

an integer-N PLL. This is also the case if N0 fraction is program-

med to 0; however, the SDM circuitry is not placed into a low

power state. Integer-N operation yields the best performance in

terms of phase noise, spurs, and jitter.

Loop Configuration 1—Low PFD Frequency

LDO_BYP

LF

REF0

REF1

REF.

INPUT

OUT0

OUT9

1.8V

CP

LOOP

÷M0,

M1

VCO

FILTER

REF_SEL

÷N0A

÷N0

To obtain the best performance in fractional-N operation,

configure the N0 modulus value to the largest possible value as

allowed by the fractional translation being synthesized. For

example, if a 19.44 MHz input is being translated to a 625 MHz

output, the required VCO operating frequency is 2500 MHz.

Using the input doubler, this requires an N divider value of 64 +

73/243. To make the modulus as large as possible, both the

modulus and fraction values must be multiplied by the same

scaling value. The scaling value is calculated as follows:

AD9576: PLL0

Figure 23. PLL0 Loop Configuration 1

The Loop 1 configuration is an integer-N configuration that

uses a cascade of two feedback dividers, N0 and N0A, to operate at

much lower PFD frequencies. In this configuration, the charge

pump current is internally set to a value of 1024 μA, an internal

switch shorts R_ZEROin the integrated loop filter and automatically

sets the integrated pole capacitor (CPOLE2) to 100 pF. This

particular internal loop filter configuration provides the flexibility

to set the response zero and the first pole frequency of the loop

filter (via an external R-C network) to accommodate a low PFD

rate. Note that Loop 1 configures PLL0 as an integer-N PLL

only. Therefore, to ensure proper device operation, the N0 SDM













2

²⁴1

modulus

16,777,215

243













Scalar = floor

= floor

= 69,042

Rev. A | Page 30 of 65

Data Sheet

AD9576

power-down bit must be set to Logic 1, or the N0 fraction value

must be set to 0.

Loop Configuration 2—Zero Delay

LDO_BYP

LF

The VCO0 frequency is a function of the PFD input frequency

(see the PLL0 Reference Frequency Scaling section) and the values

programmed into the registers associated with N0 and N0A.

REF0

REF1

REF.

INPUT

OUT0

OUT9

1.8V

CP

LOOP

FILTER

VCO ÷M0

REF_SEL

f_VCO0= f_PFD0× N0 × N0A

÷Q

ZD

The divider value of N0 is set by programming the N0 divider

integer value bits to a value between 12 and 255. N0A is a 12-bit

divider that is set by programming the N0A Divider Ratio[11:0]

bits (Register 0x10E, Bits[7:0] and Register 0x10F, Bits[3:0]) as

shown in Table 26.

AD9576: PLL0

Figure 24. PLL0 Loop Configuration 2

In the Loop 2 configuration, the total feedback division ratio is

a cascade of the VCO divider, M0, and the channel divider, Q_ZD

The channel divider, Q_ZD, operates identically to any other

channel divider configured with M0 as an input clock source;

however, the output of the divider is not routed to an output

driver, but rather to the PLL0 PFD feedback clock input. This

feedback scheme, along with Q_ZDbeing synchronized with the

other channel dividers (see the Synchronization section) allows

the loop to establish a minimal delay between the rising edges

.

Table 26. N0A Divider Ratio Decode

N0A Divider Ratio[11:0] Value

Divider Operation

Invalid setting

0 to 3

4 to 4095

Divide by this value

The overall frequency translation equation for Loop 1 is as follows:

(

N0  N0A

)

f_REF

R0

of the reference input and the output clocks. See the PLL0 VCO

Calibration section for information concerning the impact of

the Q_ZDsynchronization on the VCO0 calibration procedure.

f_OUT

=



M_ZQ_Y

where:

The VCO0 frequency is a function of the PFD input frequency

(see the PLL0 Reference Frequency Scaling section) and the values

f_OUTis the frequency at the output driver, OUTx (OUT0 through

OUT9).

programmed into the registers associated with M0 and Q_ZD

.

f_REFis the frequency of the active reference (REF0 or REF1).

M_Zis the VCO divider (M0 or M1) that is the input source of Q_Y.

Q_Yis the channel divider (Q0, Q1, Q2, or Q3) associated with

OUTx.

f_VCO0= f_PFD0× (M0 × Q_ZD)

M0 is described in detail in the PLL0 VCO Dividers (M0 and

M1) section and Q_ZDis described in detail in the Channel

Dividers section.

R0 is the divider value used to scale the input reference

frequency and is an element of the following set: {½, 1, 2 … 63}.

Note that the value of ½ is the result of selecting the ×2 reference

multiplier (see the PLL0 Reference Frequency Scaling section).

The overall frequency translation equation for Loop 2 is as follows:

M0 Q_ZD

M_ZQ_Y

f_REF

R0

f_OUT

=



N0 is an element of the following set: {12, 13 … 255}.

N0A is an element of the following set: {4, 5 … 4095}.

where:

f_OUTis the frequency at the input to the channel dividers, OUTx

(OUT0 through OUT9).

M_Zis the divide value of the VCO divider and is an element of

the following set: {2, 3 … 11}.

f_REFis the frequency of the active reference (REF0 or REF1).

Q_ZDis the zero delay feedback divider.

Q_Yis the divide value of the channel divider and is an element

of the following set: {1, 2 … 64}.

M_Zis the VCO divider (M0 or M1) that is the input source of Q_Y.

Q_Yis the channel divider (Q0, Q1, Q2, or Q3) associated with

OUTx.

R0 is the divider value used to scale the input reference

frequency and is an element of the following set: {½, 1, 2, …,

63}. Note that the value of ½ is the result of selecting the ×2

reference multiplier (see the PLL0 Reference Frequency Scaling

section).

M0 and M_Zare divide values of the VCO dividers and are

elements of the following set: {2, 3, …, 11}.

Q_ZDand Q_Yare divide values of the channel divider and are

elements of the following set: {1, 2, …, 64}.

Rev. A | Page 31 of 65

AD9576

Data Sheet

For deterministic phase alignment through a reference

switchover event, configure the output frequency of Q_ZD(and,

therefore, the PLL0 PFD frequency) such that it is equal to the

greatest common denominator (GCD) of all channel divider

output frequencies on the PLL0 synchronization domain and the

reference input.

However, the maximum value for N0 is 255. Therefore, to

calibrate the VCO, use Loop Mode 1, which requires N0 = 50

and N0A = 8. See the PLL0 VCO Calibration section for

detailed information about calibrating in Loop Mode 2 when

M0 × Q_ZD> 255.

Note that using smooth switchover minimizes the phase offset

between reference inputs for a reference switchover event.

Therefore, the use of smooth switching allows deterministic

phase alignment to be maintained through a switchover event

without the need for the reference input divider.

In the following example,

•

f

_IN= 25 MHz

_{OUT0_TO_OUT3}= 125 MHz

_{OUT4_TO_OUT5}= 312.5 MHz

PLL0 Phase Frequency Detector (PFD) and Charge Pump

_{OUT6_TO_OUT7}= 625 MHz

The PFD determines the phase difference between the edges of

the reference divider output and the feedback divider output.

The maximum operating frequency of the PFD depends on the

operating mode of the PLL (see Table 6).

_{OUT8_TO_OUT10}= 25 MHz from the PLL0 active reference input.

_PFD0= GCD (25, 125, 312.5, 625) = 12.5 MHz

_VCO0= 625 MHz × 4 = 2500 MHz

Therefore, R0 = 2 and M0 × Q_ZD= 2500/12.5 = 200. This

requires the following conditions:

The circuit provides two pulse-width modulated output signals:

up and down. These up/down pulses drive the charge pump

circuit. The instantaneous phase error determines the amount

of charge delivered from the charge pump to the loop filter. The

closed-loop of the PLL typically drives the frequency and phase

difference between the two PFD input signals toward zero.

•

M0 ≥ 4 = ceil(200/64)

M0 = 4

Q

_ZD= 50

Q0 = 5

Q1 = 2

The 1.8 V charge pump current is user-programmable in

increments of 4 µA up to 1.02 mA via the PLL0 charge pump

current bits (Register 0x102, Bits[7:0]). The charge pump

current is determined by multiplying the bit field value of the

PLL0 charge pump current bits by 4 µA. For example, the

default setting of 0x8D produces a charge pump current of

141 × 4 µA = 564 µA.

Q1 source = M0

Q2 = 1

Q2 source = M0

N0 = 200

In the following example,

•

f

_IN= 25 MHz

PLL0 Loop Filter

_{OUT0_TO_OUT3}= 156.25 MHz

The loop filter affects the dynamic characteristics of a PLL (for

example, lock time and stability). The AD9576 provides both

internal and external partially integrated loop filter capabilities

for VCO0. The loop filter used is specified by the PLL0 loop

filter bypass bit (Register 0x104, Bit 0). Setting this bit to Logic 0

uses the internal loop filter, whereas Logic 1 uses an external

loop filter for VCO0. For both the external and internal loop

filter, the value of CPOLE2 is fixed internally to 16 pF.

_{OUT4_TO_OUT5}= 125 MHz

_{OUT6_TO_OUT7}= 625 MHz

_{OUT8_TO_OUT10}= 25 MHz from the PLL0 active reference input

_PFD0= GCD (25, 125, 156.25, 625) = 6.25 MHz

_VCO0= 625 MHz × 4 = 2500 MHz

Therefore, R0 = 4 and M0 × Q_ZD= 2500/6.25 = 400. This

requires M0 ≥ 7 = ceil(400/64). M1 must be used to generate all

the required frequencies in this configuration, resulting in the

following settings:

Operating VCO0 with the internal loop filter requires a

single 4.7 nF external capacitor connected between the LF and

LDO_BYP pins. The other loop filter components are internal

and can be programmed through the PLL0 loop filter bits

(Register 0x103, Bits[7:0]). Note PLL0 uses a static charge

pump current; therefore, the nominal bandwidth of 400 kHz

varies slightly as the feedback divide ratio deviates from a value

of 50.

•

M0 = 8

_ZD= 50

Q

Q0 = 2

M1 = 4

Q1 = 5

Q1 source = M1

Q2 = 1

When VCO0 uses the external loop filter, the value of

RPOLE2 is internal and set by the PLL0 loop filter RPOLE2 bits

Q2 source = M1

N0 = 400

(Register 0x103, Bits[7:6]). The remaining components, R_ZERO

_ZERO, and CPOLE1 are external to the AD9576 and are configured

by the user.

,

C

Rev. A | Page 32 of 65

Data Sheet

AD9576

The dual VCO dividers provide flexibility for the output

frequencies. VCO Divider M0 drives the Q0, Q1, Q2, Q3, and

_ZDchannel output drivers, whereas VCO Divider M1 only

AD9576

INTERNAL

LF

19

660Ω

Q

15kΩ

drives the Q1 and Q2 channel dividers.

3.9nF

16pF

120nF

The VCO dividers, M0 and M1, have a synchronous reset function

that must be exercised after power-up or a change in divide

value to guarantee proper operation. Under normal operation,

there is no need for the user to reset the M0 or M1 dividers

manually because they are automatically reset by the VCO0

calibration process. However, when the user wants to change

the M0 or M1 divider value after the VCO0 calibration, the user

must either reissue a VCO0 calibration (see the PLL0 VCO

Calibration section) or manually reset the VCO dividers by

executing the following sequence:

LDO_BYP

20

Figure 25. 8 kHz PFD PLL0 External Loop Filter

When using an 8 kHz PFD rate, an external loop filter must be

used. Figure 25 shows the recommended external loop filter design

for an 8 kHz PFD rate. With a VCO0 frequency of 2500 MHz

and a charge pump current of 888 μA (Register 0x102, Bits[7:0] =

0xDE), the loop filter has a bandwidth of 520 Hz with 70° of

phase margin.

1. Force a reset on the M0 VCO divider. Set Register 0x120,

PLL0 Internal VCO

Bit 0 = 1.

PLL0 incorporates a low phase noise LC tank VCO0. This VCO

has 256 frequency bands spanning from 2.375 GHz to 2.75 GHz.

A VCO calibration is required to select the appropriate operating

frequency band for the programmed divider configuration (see

the PLL0 VCO Calibration section).

2. Force a reset on the M1 VCO divider. Set Register 0x120,

Bit 4 = 1.

3. Issue an input/output (I/O) update. Write Register 0x00F =

0x01.

4. Clear the M0 VCO divider reset state. Set Register 0x120,

Bit 0 = 0.

VCO0 has an integrated low dropout (LDO) linear voltage

regulator that isolates VCO0 from possible external supply

voltage variations. The regulated LDO voltage appears at the

LDO_BYP pin. To ensure stability, connect a 0.47 μF chip

monolithic ceramic capacitor between this pin and ground.

5. Clear the M1 VCO divider reset state. Set Register 0x120,

Bit 4 = 0.

6. Issue an I/O update. Write Register 0x00F = 0x01.

Note that, if only a single VCO divider value is changed, only

that divider must be reset. However, resetting both dividers

simultaneously ensures synchronization between the respective

downstream dividers.

Note that using the LDO_BYP pin to power an external circuit

may degrade VCO0 performance.

PLL0 VCO Dividers (M0 and M1)

The internal VCO of PLL0 operates in the 2.5 GHz range, which is

too high to clock the output channel dividers directly. The AD9576

has two independent VCO dividers, M0 and M1, used to scale

down the internal VCO frequency to an acceptable range for

the output channel dividers. Both the M0 and M1 dividers are

programmable over the range of 2 to 11 using the M0 divide

ratio and M1 divider ratio bits, Register 0x121, Bits[3:0] and

Register 0x121, Bits[7:4], respectively. The values of these bits

and their corresponding functions are shown in Table 27.

PLL0 VCO Calibration

The AD9576 on-chip VCO0 must be calibrated to ensure

proper operation over process and temperature. Calibration

centers the VCO0 control voltage at the VCO0 frequency

established after PLL0 locks, allowing VCO0 a sufficient

operating range to maintain lock over extremes of temperature

and voltage.

The VCO calibration routine works by comparing the VCO

feedback clock to the reference input clock. This requires that a

valid reference input clock is present at the time of calibration.

Therefore, the LOR status indicator of the PLL0 active reference

input is used to gate the VCO calibration operation so that it

waits for the presence of a reference input clock. Note that, in

Loop Mode 1, the REF0/REF1 frequency may be lower than the

detection threshold of the LOR status indicator, causing the

LOR status to remain Logic 1 even with a fully valid reference.

In this case, the VCO calibration cannot be gated by the PLL0

active reference input LOR status. Therefore, the LOR gating of

the calibration is removed when operating in Loop Mode 1 with

a total feedback divide value equal to or greater than a value of

divide by 512. When these conditions are met, the calibration

still waits for the presence of a reference input clock, but no

assessment of the frequency accuracy of the signal is made prior

to the execution of the calibration.

Table 27. VCO Divider Ratio Decode

M0 or M1 Divider Ratio Bit Field Value

Divider Operation

Power down

0 to 1

2 to 11

12 to 15

Divide by this value

Power down

Rev. A | Page 33 of 65

AD9576

Data Sheet

When a PPR load is executed on power-up, an automatic

calibration sequence is issued following the completion of the

load. Otherwise, a manual VCO0 calibration must be initiated

via the PLL0 calibration bit (Register 0x100, Bit 3). Setting the

PLL0 calibration bit to Logic 1 initiates a calibration of VCO0.

The PLL0 calibration bit is not a self clearing bit. Therefore,

the bit must be reset to Logic 0 before a subsequent manual

calibration can be initiated. The PLL0 calibration in progress

bit (Register 0x020, Bit 2) indicates when a VCO0 calibration is

occurring. A Logic 1 reported on the PLL0 calibration in progress

bit indicates a VCO0 calibration is active, whereas a Logic 0

indicates normal PLL0 operation.

Loop Mode 2 Calibration Considerations

When using the PLL0 Loop 2 feedback configuration, the

VCO0 calibration requires special treatment because the M0

and Q_ZDdividers stop during VCO0 calibration (a result of the

automatic synchronization function imposed during calibration),

which prevents the calibration circuitry from receiving the

required feedback clock edges. Therefore, the calibration

controller detects that Loop 2 is in effect and automatically

switches to the Loop 0 configuration to perform the VCO0

calibration sequence. Upon completion of the calibration

sequence, the calibration controller automatically restores the

Loop 2 configuration. Because the calibration controller uses

the Loop 0 configuration, the N0 divider is necessarily in the

feedback path during the calibration sequence. Therefore, the

user must program the value of the N0 divider before initiating

a calibration sequence in the Loop 2 configuration, where

After a successful calibration, the VCO operates in a condition

with optimal margin to maintain lock in operation across the

entire specified temperature range, which includes margin for a

deviation in the reference input clock carrier up to 200 ppm.

However, if the active reference clock frequency exceeds this

limit, or if the user alters the nominal VCO operating frequency

by reconfiguring the reference scaling section or feedback divider,

the ability for the PLL to maintain lock over temperature may be

compromised. If this occurs, an additional VCO calibration is

necessary. To accomplish this, write the following register

sequence:

N0 = M0 × Q_ZD

That is, N0 must match the product of the M0 divider and the

Q

_ZDchannel divider. The N0 divider is programmed via the N0

divider integer value bits (Register 0x107, Bits[7:0]).

If M0 × Q_ZD> 255, the N0 feedback divider alone is not large

enough to be used during calibration. To properly calibrate

VCO0, manually force the AD9576 to operate in Loop 1 during

calibration and, following the completion of the calibration,

manually force the AD9576 back to Loop 2. Perform these

actions using the following sequence:

1. Clear the VCO0 calibration bit. Write Register 0x100,

Bit 3 = 0.

2. Issue an I/O update. Write Register 0x00F = 0x01.

3. Initiate a manual VCO0 calibration. Write Register 0x100,

Bit 3 = 1.

5. Clear the VCO0 calibration bit. Write Register 0x100,

Bit 3 = 0.

4. Issue an I/O update. Write Register 0x00F = 0x01.

6. Set Loop Mode 1. Write Register 0x101, Bits[2:1] = 1.

7. Issue an I/O update. Write Register 0x00F = 0x01.

8. Initiate a manual VCO0 calibration. Write Register 0x100,

Bit 3 = 1.

Note that, during the first VCO0 calibration sequence after a

PLL0 reset or chip level reset, the calibration controller holds

the distribution section in sync mode (the channel dividers are

held in reset and the output drivers are static) until the calibration

terminates. Therefore, no output signals appear until the VCO0

calibration sequence terminates, as indicated by a Logic 1 to

Logic 0 transition of the PLL0 calibration in progress bit

(Register 0x020, Bit 2).

9. Issue an I/O update. Write Register 0x00F = 0x01.

10. Wait for the calibration to complete, the poll until

Register 0x020, Bit 2 = 0.

11. Set Loop Mode 2. Write Register 0x101, Bits[2:1] = 2.

12. Issue an I/O update. Write Register 0x00F = 0x01.

The VCO0 calibration process requires approximately 98,500

cycles of the PFD to complete. Therefore, the calibration time

(t_{VCO_CAL}) depends on the input frequency to the PFD (f_PFD) as

follows:

Note that, in this case, the calibration feedback path consists of

the cascade of the N0 and N0A dividers. Therefore, the user

must program the N0 and N0A dividers such that

N0 × N0A = M0 × Q_ZD

9.8510⁴

t_{VCO_CAL}

=

f_PFD

Rev. A | Page 34 of 65

Data Sheet

AD9576

PLL0 Lock Detect

Note that, when the ×2 frequency multiplier is in use, the active

reference signal must have a duty cycle close to 50%. Otherwise,

spurious artifacts (harmonics) may propagate through the signal

path and appear at the output of PLL1.

The PLL0 lock detector is a frequency detector that evaluates

the frequency difference between the feedback and reference

inputs to the PFD. A lock condition is indicated when the

average difference between the feedback and reference inputs is

less than a magnitude of 16 ppm. The PLL0 lock detect process

requires approximately 65,500 cycles of the PFD to complete.

Therefore, the lock detect time (t_LDET) depends on the input

frequency to the PFD (f_PFD) as follows:

PLL1 Loop Configuration

The VCO₁frequency is a function of the PFD1 input frequency

and the values programmed into the registers associated with

the N₁feedback divider.

f_VCO1= f_PFD1× N₁

6.510⁴

The divider value of N₁is set by programming the N1 divider

ratio bits (Register 0x201, Bits[7:0]) to a value between 4 and 255.

t_LDET

=

f_PFD

PLL1 INTEGER-N PLL

The overall frequency translation is as follows:

PLL1 is a fully integrated integer-N PLL consisting of six

functional elements: a reference frequency prescalar, a PFD, a

charge pump, an internal loop filter, a VCO, and a feedback divider.

PLL1 allows two independent reference clock input signals. PLL1

provides up to three outputs segregated into two groups. Each

group has a dedicated channel divider allowing the device to

produce two different output frequencies simultaneously. Figure 26

shows the functional block diagram of PLL1.

f_REF

N₁



R1 Qx

f_OUT

=

where:

f_OUTis the frequency at the output driver, OUTx (OUT8, OUT9,

or OUT10).

f_REFis the frequency of the active reference (REF0, REF1, or REF2).

Qx is the channel divider (Q3 or Q4) associated with OUTx.

R1 is the divider value used to scale the input reference frequency

and is an element of the following set: {½, 1, 1.5, 2, 3, 4, 6, 8}.

Note the value of ½ is the result of selecting the ×2 reference

multiplier (see the PLL1 Reference Frequency Scaling section).

PLL1

INTEGER-N

÷N1

REF2

×2

CHARGE

PUMP

VCO1

N₁is an element of the following set: {4, 5, …, 255}.

PLL0 ACTIVE

REFERENCE

LPF

÷R1

Qx is the divide value of the channel divider and is an element

of the following set: {1, 2, …, 64}.

Figure 26. PLL1 Block Diagram

PLL1 PFD, Charge Pump, and Loop Filter

PLL1 Reference Frequency Scaling

The PFD determines the phase difference between the edges of

the reference divider output and the feedback divider output.

The circuit provides two pulse-width modulated output signals:

up and down. These up/down pulses drive the charge pump

circuit. The instantaneous phase error determines the amount

of charge delivered from the charge pump to the loop filter. The

closed-loop of the PLL typically drives the frequency and phase

difference between the two PFD input signals towards zero.

The frequency of the active input reference (REF0, REF1, or

REF2) is scalable via the PLL1 doubler enable bit (Register 0x202,

Bit 0) and the R1 divider ratio bits (Register 0x202, Bits[3:1]). This

scaling allows the user to scale the input reference frequency to

satisfy the input range of the PFD. When the PLL1 doubler

enable bit is set to Logic 0, the frequency appearing at the input

to the PFD, f_PFD1, is a function of the active reference frequency

scaled by the reference input divider.

The loop filter affects the dynamic characteristics of a PLL (for

example, lock time and stability). PLL1 has a fully integrated

internal loop filter that establishes the loop dynamics for a PFD

frequency between 10 MHz and 50 MHz. The charge pump

current and loop filter components are automatically adjusted

based on the programmed N1 feedback divide value to

maintain a nearly constant loop bandwidth over a range of

feedback dividers values. Table 28 shows the PLL1 closed-loop

bandwidth as a function of the N1 divide value.

f_REF

f_PFD1

where:

=

R1

f_REFis the frequency of the active reference (REF0, REF1, or

REF2).

R1 is the value of the R1 reference input divider value.

When the PLL1 doubler enable bit is set to Logic 1, the frequency

appearing at the input to the PFD, f_PFD1, is the active reference

frequency multiplied by a factor of 2.

Table 28. PLL1 Closed-Loop Bandwidth

N1 Divide Value

4 to 23

Nominal Closed Loop Bandwidth (MHz)

f_PFD1= f_REF× 2

3.5

1.75

1

where f_REFis the frequency of the active reference (REF0, REF1,

24 to 47

or REF2).

48 to 255

Rev. A | Page 35 of 65

AD9576

Data Sheet

PLL1 Internal VCO

of the input clock period. For Output Group 0, if the M0 output

clock is 625 MHz, the LSB of this bit field corresponds to 800 ps

of phase delay and an initial phase offset value of 23 delays the

first edge of the Q0 divider output by 18.4 ns relative to an

initial phase offset value of 0. To guarantee the initial phase

offset of the Qx channel divider, a synchronization command

must be executed on Qx after the corresponding Qx initial

phase bit field is programmed by the user. Refer to the

Synchronization section for additional information regarding

this process.

The PLL1 internal VCO has a frequency range of 750 MHz to

825 MHz and a nominal gain of 750 MHz/V, allowing the PLL to

support 3.125% clock margining for an 800 MHz VCO

frequency and a 25 MHz PFD frequency by updating the

feedback divider on-the-fly.

PLL1 Lock Detect

The PLL1 lock detect is a phase detector that evaluates the

phase difference between the feedback and reference inputs to

PFD1. The lock detector operates at the PFD rate, which is

Each channel divider can be independently powered down

using the respective power-down bits. These bits are the Q0 PD

(Register 0x140, Bit 6), Q1 PD (Register 0x146, Bit 6), Q2 PD

(Register 0x14A, Bit 6), Q3 PD (Register 0x240, Bit 6), and Q4

PD (Register 0x244, Bit 6) bits in the serial register. When the

channel divider power-down bit is set to Logic 1, the respective

channel divider powers down, whereas Logic 0 powers up the

channel divider for normal operation.

f_VCO1

f_PFD1

=

N₁

A lock condition is indicated when the phase error between the

feedback and reference inputs to PFD1 is less than 3.25 ns.

Typically, a lock condition for PLL1 is declared 420 µs after the

RESET

release of

, assuming a valid input clock is available.

OUTPUT DISTRIBUTION

Input Sources

The output distribution is segmented into five groups of outputs

(Output Group 0, Output Group 1, Output Group 2, Output

Group 3, and Output Group 4) with each group having several

output drivers that share a channel divider. The output groups,

corresponding channel dividers, output drivers, and input clock

source(s) are shown in Table 29.

The Q0 and Q_ZDchannel dividers are driven solely by the M0

VCO divider output clock. The Q1 and Q2 channel dividers can

be driven by the output clock from either VCO divider, M0 or

M1. The user must select which VCO divider is driving the Q1

and Q2 channel dividers using the Qx source bits (Register 0x147,

Bit 6 for the Q1 source and Register 0x14B, Bit 6 for the Q2 source).

Programming either Qx source bit to Logic 0 selects the M0 output

clock as the input clock for the channel divider, whereas Logic 1

selects the M1 output clock as the channel divider input clock.

Table 29. Distribution Output Groups

Output

Group

Channel

Divider

Output

Driver(s)

Frequency

Source(s)

0

Q0

OUT0, OUT1,

OUT2, OUT3

PLL0 (M0)

The Q3 channel divider can be driven by the output clock from

the M0 VCO divider or the output of PLL1, f_VCO1. The user must

select which input is driving the Q3 channel divider using the

Q3 source bit (Register 0x241, Bit 6). Programming this bit to

Logic 0 selects the PLL1 output as the Q3 input, whereas a

Logic 1 selects the M0 output as the Q3 input.

1

2

3

Q1

Q2

Q3

OUT4, OUT5

OUT6, OUT7

OUT8, OUT9

PLL0 (M0 and M1)

PLL0 (M0), PLL1

output, PLL1

reference

The Q4 channel divider is driven solely by the output of PLL1, f_VCO1

.

4

Q4

OUT10

PLL1 output, PLL1

reference

Synchronization

Channel Dividers

Each channel divider has a sync input that allows the divider to

be placed into a known phase, determined by its initial phase bit

field. When the sync input is Logic 1, the divider is held in reset,

which establishes the initial phase of the divider. When the sync

input is logic low, the divider is in normal operation. Coordinating

the Logic 1 to Logic 0 transition of the sync input of multiple

channel dividers to occur simultaneously results in a deterministic

initial phase alignment between the outputs of said dividers.

Provided the set of synchronized dividers share a common input

clock, the initial phase alignment is repeated at a rate equal to

the GCD between all channel divider outputs.

There are a total of six, 6-bit integer channel dividers: Q0, Q1,

Q2, Q3, Q4, and Q_ZD. The divider ratio is programmable using

the Qx divider ratio bits, Register 0x140, Bits[5:0], Register 0x146,

Bits[5:0], Register 0x14A, Bits[5:0], Register 0x240, Bits[5:0],

Register 0x244, Bits[5:0], and Register 0x110, Bits[5:0] for Q0,

Q1, Q2, Q3, Q4, and Q_ZD, respectively. Each channel divider can

operate in divide ratios of 1 to 64. The default divide ratio for

each channel divider is divide by 4, with the exception of Q_ZD

which has a default value of 1.

,

The initial phase offset for each channel divider is programmable

through the Qx initial phase bit fields: Register 0x141, Bits[5:0],

Register 0x147, Bits[5:0], Register 0x14B, Bits[5:0], Register 0x241,

Bits[5:0], Register 0x245, Bits[5:0], and Register 0x110, Bits[5:0]

for Q0, Q1, Q2, Q3, Q4, and Q_ZD, respectively. The bit fields

each have a programming range of 0 to 63 in units of half cycles

Rev. A | Page 36 of 65

Data Sheet

AD9576

As an example, assume the Q0 output is 50 MHz and the Q1

output is 100 MHz. The outputs have a GCD equal to 50 MHz;

therefore, the initial phase relationship between the Q0 and Q1

channel divider outputs repeats every 20 ns (for example, at a

50 MHz rate).

To manually synchronize a sync domain, the user must

program the associated manual sync bit to a Logic 1 followed by

a Logic 0. The following example shows the required sequence

for the PLL0 synchronization domain:

13. Set the PLL0 sync bit. Write Register 0x100, Bit 2 = 1.

14. Issue an I/O update. Write Register 0x00F = 0x01.

15. Clear the PLL0 sync bit. Write Register 0x100, Bit 2 = 0.

16. Issue an I/O update. Write Register 0x00F = 0x01.

Consider another example: assume that the Q0 output is 50 MHz,

the Q1 output is 100 MHz, and the Q2 output is 125 MHz. The

outputs have a GCD equal to 25 MHz; therefore, the initial

phase relationship between the Q0, Q1, and Q2 channel divider

outputs repeats every 40 ns (for example, at a 25 MHz rate).

Note that the M0 and M1 sync domains (and therefore the PLL0

sync domain) have mask sync bits (see the Register 0x122

description in Table 48). Setting a channel divider mask sync bit

for a particular sync domain precludes said sync domain from

affecting the operation of that channel divider. For example, if

the Q1, Q2, and Q3 source bits are all programmed to Logic 0,

Four synchronization domains exist to facilitate the synch-

ronization of multiple channel dividers. A single synchronization

domain is a grouping of channel dividers in which the sync

inputs of each channel divider are tied to a common control bit.

The channel dividers are grouped based on their selected input

source, and the four domains are as follows:

the M0 sync domain includes the Q0, Q1, Q2, and Q

_ZDchannel

dividers, the M1 sync domain does not include channel dividers,

and the PLL1 sync domain includes the Q3 and Q4 channel

dividers. Programming the M0 mask sync Q2 (Register 0x122,

Bit 2) to Logic 1 results in the Q2 channel divider being unaffected

by a M0 or PLL0 sync command. Programming the M1 mask

sync Q2 (Register 0x122, Bit 6) to Logic 1 has no functional

impact because Q2 is not a part of the M1 sync domain in this

configuration.

•

M0 sync domain. This domain includes all channel dividers

that are configured to use the M0 VCO divider as the input

clock source.

•

M1 sync domain. This domain includes all channel dividers

that are configured to use the M1 VCO divider as the input

clock source.

•

PLL0 sync domain. This domain includes consists of the

aggregate of the M0 and M1 sync domains.

PLL1 sync domain. This domain includes includes all

channel dividers that are configured to use the PLL1

output as the input clock source

Output Driver Sources

The output drivers in Output Group 0, Output Group 1, and

Output Group 2 (see Table 29) are driven by the outputs of their

respective channel divider. For example, OUT4 and OUT5 in

Output Group 1 are driven by the output of the Q1 channel

divider.

Each sync domain has an associated manual sync bit—

Register 0x120, Bit 2, Register 0x120, Bit 6, Register 0x100,

Bit 2, and Register 0x200, Bit 2 for the M0, M1, PLL0, and PLL1

sync domains, respectively. Each manual sync bit allows user

control of the divider sync inputs, but there are also automatically

generated signals that are logically OR’ed with the manual sync

bits of the individual sync domains. The actions that generate

these automatically generated sync signals are described as

follows, for the sync domains they affect:

Output Group 3 or Output Group 4 can be driven by the output

of their respective channel divider or by the PLL1 active input

reference. The user must select which source is driving the outputs

in Output Group 3 and Output Group 4. For Output Group 3,

this is accomplished by programming the OUT89 source bit

(Register 0x241, Bit 7). Programming this bit to Logic 0 selects

the Q3 output as the input for the OUT8/OUT9 output drivers,

whereas a Logic 1 selects the PLL1 active input reference as the

input to the output drivers. Note that, if the PLL1 active input

reference is selected as the source to an output group and the

PLL1 active input reference is configured for a XTAL, the PLL1

active input reference loss of reference signal gates the output

drivers of the output group.

•

M0 sync domain. Deassertion of the M0 reset bit

(Register 0x120, Bit 0) and deassertion of the M0 power-down

bit (Register 0x120, Bit 1).

M1 sync domain. Deassertion of the M1 reset bit

(Register 0x120, Bit 4) and deassertion of the M1 power-

down bit (Register 0x120, Bit 5).

The input clock source for OUT10 is selected via the OUT10

source bit (Register 0x245, Bit 6). Programming this bit to

Logic 0 selects the output of the Q4 divider as the clock source

for OUT10, whereas a Logic 1 selects the PLL1 active input

reference as the OUT10 clock source.

PLL0 sync domain. Completion of the first VCO0 calibration

routine issued after the deassertion of any chip level reset

or deassertion of the PLL0 reset bit (Register 0x100, Bit 0).

Note that this automatic sync affects both the M0 and M1

sync domains.

•

PLL1 sync domain. Deassertion of the PLL1 reset bit

(Register 0x200, Bit 0).

Note that, if none of the 3-channel output drivers, OUT8,

OUT9, or OUT10, use the PLL1 output as their input, then the

PLL1 power-down signal is automatically asserted, and PLL1 is

powered down.

Rev. A | Page 37 of 65

AD9576

Data Sheet

When OUT8, OUT9, or OUT10 is operating in the CMOS

Output Power-Down

output format, the user must also select the polarity of the

output driver via the OUTx CMOS polarity bits (Register 0x242,

Bits[3:2], Register 0x243, Bits[3:2], and Register 0x246, Bits[3:2]).

For example, the polarity of OUT8 is controlled via the OUT8

CMOS polarity bits (Register 0x242, Bits[3:2]). Table 51

contains a detailed description of the OUTx CMOS polarity bit

fields for OUT8, OUT9, and OUT10.

The eight output drivers, OUT0 through OUT7, have independent

power-down control via the corresponding OUTx PD bits in the

serial register. For example, the OUT0 output driver is powered

down via the OUT0 PD bit (Register 0x142, Bit 2). When the

corresponding OUTx PD bit is set to Logic 1, OUTx is powered

down; otherwise, it is powered on and functionally operational.

The three output drivers, OUT8, OUT9, and OUT10 have

independent power-down control via the corresponding OUTx

enable bits. For example, the OUT8 output driver is powered

down via the OUT8 enable bit (Register 0x242, Bit 0). When the

corresponding driver enable bit is set to Logic 0, the OUTx

output driver is powered down. Likewise, OUTx is powered up

when the corresponding OUTx PD bit is set to Logic 1.

Additionally, when the output format for OUT8, OUT9, or

OUT10 is configured for either LVDS or full swing CMOS, the

driver strength of the output is determined by the OUTx drive

strength bits (Register 0x242, Bit 1, Register 0x243, Bit 1, and

Register 0x246, Bit 1 for OUT8, OUT9, and OUT10, respectively).

When operating in the LVDS output format (OUTx driver

format bit = 010), programming this bit to Logic 0 results in an

output drive strength of 3.5 mA, whereas a Logic 1 produces a

drive strength of 4.5 mA.

Output Driver Format

The OUT0 through OUT7 output channels support HSTL,

LVDS, and 1.8 V CMOS outputs. The user has independent

control of the operating mode of each of the eight output

channels via the OUTx driver format bits in the serial register

(for example, Register 0x142, Bits[1:0] for OUT0). Table 49

contains a detailed description of the OUTx driver format bit

fields for OUT0 through OUT7. The differential resistive load

termination is removed for 1.8 V CMOS outputs. When an

OUT0 through OUT7 driver is configured as 1.8 V CMOS, the

positive and negative pins are in a complimentary phase

relationship (for example, 180° offset).

When operating in the full swing CMOS output format,

programming this bit to Logic 0 results in nominal output drive

strength, whereas a Logic 1 results in low output drive strength

that can be used to minimize coupling effects. The drive strength

bit only applies to the full swing CMOS format. The 1.8 V swing

CMOS output drivers only operate in a low drive strength mode.

PPRx PINS

The AD9576 makes use of four PPRx pins to configure the

device. Internal circuitry scans the PPRx pins for the presence

of resistor terminations and configures the device accordingly.

A PPRx pin scan occurs automatically as part of the power-on

reset sequence (see the Power-On Reset (POR) section) or

Use HSTL format and ac couple the output signal for an

LVPECL-compatible output.

The OUT8, OUT9, and OUT10 output channels also support

HSTL, LVDS, and 1.8 V CMOS outputs as well as HCSL and

full swing CMOS outputs. The user has independent control of the

operating mode of OUT8, OUT9, and OUT10 through the OUTx

driver format bits (Register 0x242, Bits[6:4], Register 0x243,

Bits[6:4], and Register 0x246, Bits[6:4]). Table 51 contains a

detailed description of the OUTx driver format bit fields for

OUT8, OUT9, and OUT10.

RESET

following the assertion of the

pin.

Each PPRx pin controls a specific function or functional block

within the device (see Table 30). The power-on configuration of

a functional block depends on the scanned state of the corre-

sponding PPRx pin. The scan of a PPRx pin identifies one of

eight possible states based on an external pull-up or pull-down

resistor (maximum 10% tolerance) per Table 31.

When OUT8, OUT9, or OUT10 are operating in the CMOS

output format, the user must select the output swing level via

the OUTx CMOS enable full swing bits (Register 0x242, Bit 7,

Register 0x243, Bit 7, and Register 0x246, Bit 7). For example,

OUT8 is controlled via the OUT8 CMOS enable full swing bit

(Register 0x242, Bit 7). When the OUTx CMOS enable full

swing bit is set to Logic 0, the CMOS ouput of the corresponding

driver has a 1.8 V swing. When the OUTx CMOS enable full

swing bit is set to Logic 1, the CMOS swing is determined by

the voltage applied to VDD_OUTx. Only set the OUTx CMOS

enable full swing bits to Logic 1 if the associated output format

is configured as CMOS.

Table 30. PPRx Pin Function Assignments

Mnemonic

Pin No.

Function Assignment

PPR0

24

Input receiver configurations, PLL1

source, and PLL input doubler states

PPR1

26

OUT10 configuration

PPR2, PPR3

32, 56

PLL0 frequency translation and OUT0

to OUT9 configuration

Rev. A | Page 38 of 65

Data Sheet

AD9576

Device programming consists of connecting the appropriate

value programming resistors to the PPRx pins and terminating the

resistors to V_{DD_x}or GND (per Table 31). For example, Figure 27

shows how to program PPR0 to State 3.

For details regarding the device configuration based on the

scanned PPRx states, refer to the description of each PPRx pin

in the following sections.

PPR0—Reference Clock Input Configuration

The PPR0 pin controls the configuration of the reference clock

inputs (REF0, REF1, REF2) and the select line of the PLL1

reference input mux. Table 32 associates each PPR0 state with a

particular reference input configuration and PLL1 source

combination.

Table 31. PPRx State

PPRx State

Resistance

820 Ω

Terminus

GND

V_DD

0

1

2

3

4

5

6

7

1.8 kΩ

3.9 kΩ

8.2 kΩ

820 Ω

PPR1—OUT10 Configuration

The PPR1 pin controls the frequency, driver format, and source

of OUT10, which requires the PLL1 reference input, and therefore

REF2, if used, to be 25 MHz. Note that, if REF0/REF1 is configured

to a frequency other than 25 MHz, the PLL1 source must be

configured as REF2. Table 33 associates each PPR1 state with a

particular OUT10 configuration.

1.8 kΩ

3.9 kΩ

8.2 kΩ

V_DD

AD9576

PPR2 and PPR3—REF0/REF1 Frequency and OUT0 to

OUT9 Configuration

24

PPR0

8.2kΩ

The PPR2 and PPR3 pins control the configuration of the REF0

and REF1 input frequency, PLL0, OUT0 to OUT9 driver format

and frequency, and the OUT8 to OUT9 source. Table 34 associates

each combination of PPR2 and PPR3 states with a particular

predefined frequency translation.

Figure 27. PPRx Programming Resistor Example

Table 32. PPR0—Input Receiver Formats and PLL1 Source

PPR0 State REF0/REF1 Input Configuration REF2 Input Configuration

PLL1 Source

PLL0 active reference

REF2

PLL0 Doubler PLL1 Doubler

0

1

2

3

4

5

6

7

XTAL

2.5 V/3.3 V CMOS

XTAL

Enabled

Disabled

Enabled

Disabled

2.5 V/3.3 V CMOS

Differential/1.8 V LVCMOS

XTAL

2.5 V/3.3 V CMOS

Differential/1.8 V LVCMOS

2.5 V/3.3 V CMOS

XTAL

REF2

2.5 V/3.3 V CMOS

REF2

Table 33. PPR1—OUT10 Configuration

PPR1 State

OUT10 Frequency (MHz)

OUT10 Format

2.5 V/3.3 V CMOS

LVDS

OUT10 Source

0

1

2

3

4

5

6

7

25

PLL1 reference

PLL1 output

33.3 (100/3)

50

66.67 (200/3)

100

133.3 (400/3)

200

LVDS

400

LVDS

Rev. A | Page 39 of 65

AD9576

Data Sheet

Table 34. PPR2 and PPR3—REF0/REF1 Frequency and OUT0 to OUT9 Configuration¹

REF0/REF1

OUT0 to OUT3

OUT4 to OUT5

OUT6 to OUT7

OUT8 to OUT9

PPR2

State

PPR3

State

Frequency

(MHz)

Frequency

(MHz)

Frequency

(MHz)

Frequency

(MHz)

Format

N/A

Format

N/A

(MHz)

Disabled

156.25

100

Format

N/A

Format

N/A

Source

N/A

0

1

2

3

25

Disabled

156.25

Disabled

156.25

Disabled

156.25

25

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

PLL0

2.5 V/3.3 V

CMOS

PLL1

source

0

1

4

5

6

7

0

1

25

156.25

LVDS

HSTL

LVDS

HSTL

156.25

125

LVDS

HSTL

LVDS

HSTL

100

25

HSTL

25

50

25

2.5 V/3.3 V

CMOS

PLL1

source

2.5 V/3.3 V

CMOS

PLL1

125

2.5 V/3.3 V

CMOS

PLL1

source

125

2.5 V/3.3 V

CMOS

PLL1

source

125

2.5 V/3.3 V

CMOS

PLL1

source

125

25

2.5 V/3.3 V

CMOS

PLL1

source

1

2

3

4

25

156.25

HSTL

LVDS

100

HSTL

LVDS

50

HSTL

LVDS

125

25

HSTL

PLL0

50

100

2.5 V/3.3 V

CMOS

PLL1

source

1

5

6

25

156.25

HSTL

LVDS

100

HSTL

LVDS

25

HSTL

25

2.5 V/3.3 V

CMOS

PLL1

source

2.5 V/3.3 V

CMOS

PLL1

source

1

2

7

0

1

25

156.25

HSTL

LVDS

HSTL

100

HSTL

LVDS

HSTL

125

HSTL

LVDS

HSTL

312.5

25

HSTL

LVDS

HSTL

PLL0

100

312.5

PLL1

source

2

25

156.25

LVDS

312.5

LVDS

125

LVDS

25

LVDS

PLL1

source

2

3

4

5

6

7

0

1

2

3

4

25

312.5

625

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

100

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

100

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

156.25

125

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

PLL0

100

125

100

125

100

156.25

100

312.5

156.25

100

125

100

25

PLL1

source

3

5

25

100

LVDS

312.5

LVDS

156.25

LVDS

25

LVDS

PLL1

source

3

4

6

7

0

1

2

3

4

25

100

125

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

100

125

100

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

100

125

100

25

HSTL

LVDS

HSTL

LVDS

HSTL

LVDS

HSTL

100

HCSL

HSTL

LVDS

HSTL

LVDS

HSTL

PLL0

PLL1

100

125

100/3

25

PLL1

source

4

5

25

125

LVDS

100

LVDS

25

LVDS

25

LVDS

PLL1

source

4

6

7

25

LVDS

25

LVDS

125

LVDS

HSTL

100

25

HCSL

PLL0

100

2.5 V/3.3 V

CMOS

PLL1

source

5

0

25

100

HSTL

100

HSTL

125

HSTL

25

2.5 V/3.3 V

CMOS

PLL1

source

Rev. A | Page 40 of 65

Data Sheet

AD9576

REF0/REF1

OUT0 to OUT3

Frequency

OUT4 to OUT5

Frequency

OUT6 to OUT7

Frequency

OUT8 to OUT9

PPR2

State

PPR3

State

Frequency

(MHz)

Frequency

(MHz)

Format

(MHz)

Format

(MHz)

Format

Source

5

1

25

156.25

HSTL

50

HSTL

125

HSTL

25

2.5 V/3.3 V

CMOS

PLL1

source

5

2

25

156.25

LVDS

50

LVDS

125

LVDS

25

2.5 V/3.3 V

CMOS

PLL1

source

5

3

25

100

HSTL

LVDS

HSTL

LVDS

HSTL

100

25

HSTL

LVDS

HSTL

LVDS

HSTL

100

25

HSTL

LVDS

HSTL

LVDS

HSTL

100

400

25

HCSL

LVDS

HCSL

HSTL

PLL1

5

4

100

5

25

5

6

156.25

70.656

50

125

70.656

5

6²

7

0²

50

70.656

PLL1

source

6²

1²

2²

3²

25

24.576

HSTL

LVDS

HSTL

24.576

HSTL

LVDS

HSTL

24.576

HSTL

LVDS

HSTL

100

HCSL

PLL1

312.5 ×

(33/32)

156.25 ×

(33/32)

156.25 ×

(33/32)

6²

4²

25

312.5 ×

(33/32)

LVDS

156.25 ×

(33/32)

LVDS

156.25 ×

(33/32)

LVDS

100

HCSL

PLL1

6²

6³

5²

6²

7³

25

148.5

HSTL

LVDS

148.5

HSTL

LVDS

HSTL

148.5

HSTL

LVDS

HSTL

100

HCSL

PLL1

25

19.44

625 × (33/32) HSTL

156.25 ×

(33/32)

156.25 ×

(33/32)

7³

0³

19.44

625 × (33/32) LVDS

156.25 ×

(33/32)

LVDS

156.25 ×

(33/32)

LVDS

100

HCSL

PLL1

7³

1³

2³

3³

19.44

30.72

156.25

HSTL

LVDS

HSTL

125

50

HSTL

LVDS

HSTL

50

HSTL

LVDS

HSTL

100

25

LVDS

PLL1

PLL0

50

125

2.5 V/3.3 V

CMOS

7³

4³

30.72

156.25

LVDS

50

LVDS

125

LVDS

25

2.5 V/3.3 V

CMOS

PLL0

7³

7

5³

6³

7

30.72

156.25

HSTL

LVDS

125

HSTL

LVDS

50

HSTL

LVDS

100

HCSL

PLL1

30.72

Reserved

¹N/A means not applicable.

²Frequency translation requires the PLL0 input doubler to be enabled. Only valid if PPR0 = 0, 1, 4, 5, 6, or 7.

³PLL1 input must be 25 MHz. Only valid if PPR0 = 4, 5, 6, or 7.

sequence, which results in the configuration of the internal

registers. With a reference signal applied to the input of each

PLL, the VCO0 calibration sequence initiates, while PLL1

immediately begins locking to the reference. Assuming a valid

input reference signal, the PLLs eventually locks to the reference

signal(s), as indicated by assertion of the LD_0 pin and the

LD_1 pin. These lock signals enable the prescale dividers at the

output of each VCO, which starts the output drivers toggling

(that is, those output drivers enabled per the PPRx settings).

POWER-ON RESET (POR)

Applying power to the AD9576 causes an internal power-on

reset (POR) event. A POR event allows the device to initialize to

a known state at power-up by initiating a scan of the PPRx pins

(see the PPRx Pins section).

In general, the AD9576 follows an orderly power-on sequence

beginning with the POR circuit detecting a valid 2.5 V or 3.3 V

supply. This activates the internal LDO regulators. Detection of

valid LDO voltages by the POR circuit triggers a PPRx scan

Rev. A | Page 41 of 65

AD9576

Data Sheet

SERIAL CONTROL PORT

The AD9576 serial control port is a flexible, synchronous serial

communications port that provides a convenient interface to

many industry-standard microcontrollers and microprocessors.

The AD9576 serial control port is compatible with I²C and SPI.

The serial control port allows read/write access to the AD9576

register map.

CS

(chip select) pin is an active low control that gates read

The

CS

and write operations. Assertion (active low) of the

pin initiates

a write or read operation to the AD9576 SPI port. Any number

of data bytes can be transferred in a continuous stream. The

register address is automatically incremented or decremented

based on the setting of the address ascension bit (Register 0x000).

CS

must be deasserted at the end of the last byte transferred,

The AD9576 uses the Analog Devices unified SPI protocol (see

the Analog Devices Serial Control Interface Standard) implement-

ation, but does not support a 4-wire protocol with dedicated input

and output data pins. Rather, only a 3-wire mode with a single,

bidirectional data pin is supported. The SPI port configuration

is programmable via Register 0x000. This register is a part of

the SPI control logic rather than in the register map and is

distinct from the I²C Register 0x000.

CS

thereby ending the stream mode. When

pin goes into a high impedance state.

is high, the SDIO

Implementation Specific Details

The following product specific items are defined in the unified

SPI protocol:

•

Analog Devices unified SPI protocol revision: 1.0

Chip type: 0x5

Although the AD9576 supports both the SPI and I²C serial port

protocols, only one is active following power-up (as determined

by the SP0 and SP1 pins during the start-up sequence). The only

way to change the serial port protocol is to reset (or power cycle)

the device.

Product ID: 0x014F

Physical layer: 3-wire supported and 2.5 V and 3.3 V

operation supported

•

Optional single-byte instruction mode: not supported

Data link: not used

SPI/I²C PORT SELECTION

Control: not used

Because the AD9576 supports both SPI and I²C protocols, the

active serial port protocol depends on the logic state of the SP0

and SP1 pins at reset or power-on. See Table 35 for the serial

port configuration decode.

Communication Cycle—Instruction Plus Data

The unified SPI protocol consists of a two part communication

cycle. The first part is a 16-bit instruction word that is coincident

with the first 16 SCLK rising edges and a payload. The instruction

word provides the AD9576 serial control port with information

Table 35. SPI/I²C Serial Port Setup

SP1

SP0

SPI/I²C Address

SPI with PPRx load

I²C, 0111001 (0x39)

I²C, 0111010 (0x3A)

I²C, 0111011 (0x3B)

I²C, 0111100 (0x3C)

I²C, 0111101 (0x3D)

I²C, 0111110 (0x3E)

I²C, 0111111 (0x3F)

SPI

W

regarding the payload. The instruction word includes the R/

Floating

bit that indicates the direction of the payload transfer (that is, a

read or write operation). The instruction word also indicates

the starting register address of the first payload byte.

0

Floating

1

Floating

0

1

Write

0

1

If the instruction word indicates a write operation, the payload

is written into the serial control port buffer of the AD9576. Data

bits are registered on the rising edge of SCLK. Generally, it does

not matter what data is written to blank registers; however, it is

customary to use 0s. Note that the user must verify that all

reserved registers within a specific range have a default value of

0x00; however, Analog Devices makes every effort to avoid

having reserved registers with nonzero default values.

Floating

0

1

SPI SERIAL PORT OPERATION

Pin Descriptions

The SCLK (serial clock) pin serves as the serial shift clock. This

pin is an input. SCLK synchronizes serial control port read and

write operations. The rising edge SCLK registers write data bits,

and the falling edge registers read data bits. The SCLK pin

supports a maximum clock rate of 50 MHz.

Most of the serial port registers are buffered. Therefore, data

written into buffered registers does not take effect immediately.

An additional operation is needed to transfer buffered serial

control port contents to the registers that actually control the

device. This transfer is accomplished with an I/O update operation,

which is performed by writing a Logic 1 to Register 0x00F, Bit 0

(this bit is an autoclearing bit). The user can change as many

register bits as desired before executing an I/O update. The I/O

update operation transfers the buffer register contents to their

active register counterparts.

The SPI port supports only a 3-wire (bidirectional) hardware

configuration. This 3-wire mode uses the SDIO (serial data

input/output) pin for transferring data in both directions. Both

MSB first and LSB first data formats are supported and are

software programmable.

Rev. A | Page 42 of 65

Data Sheet

AD9576

Read

1. Immediately after the LSB first bit(s) is set, subsequent serial

control port operations are LSB first.

If the instruction word indicates a read operation, the next

N × 8 SCLK cycles clock out the data starting from the address

specified in the instruction word. N is the number of data bytes

read. The read back data is driven to the pin on the falling edge

and must be latched on the rising edge of SCLK. Blank registers

are not skipped over during read back.

Address Ascension

If the address ascension bits (Register 0x0000, Bit 5 and Bit 2)

are zero, the serial control port register address decrements

from the specified starting address toward Address 0x0000.

If the address ascension bits (Register 0x0000, Bit 5 and Bit 2)

are one, the serial control port register address increments from

the starting address toward Address 0x7FFF. Reserved addresses

are not skipped during multi-byte input/output operations;

therefore, write the default value to a reserved register and 0s to

unmapped registers. Note that it is more efficient to issue a new

write command than to write the default value to more than

two consecutive reserved (or unmapped) registers.

A read back operation takes data from either the serial control

port buffer registers or the active registers, as determined by

Register 0x001, Bit 5.

SPI Instruction Word (16 Bits)

W

The MSB of the 16-bit instruction word is R/ , which indicates

whether the instruction is a read or a write. The next 15 bits are

the register address (A14 to A0), which indicates the starting

register address of the read/write operation (see Table 37).

Table 36. Streaming Mode (No Addresses Skipped)

SPI MSB/LSB First Transfers

Address Ascension

Increment

Stop Sequence

0x0000 … 0x7FFF

0x7FFF … 0x0000

The AD9576 instruction word and payload can be MSB first or

LSB first. The default for the AD9576 is MSB first. The LSB first

mode can be set by writing a 1 to Register 0x0000, Bit 6 and Bit

Decrement

Table 37. Serial Control Port, 16-Bit Instruction Word

MSB

LSB

I0

I15

I14

I13

I12

I11

I10

I9

I8

I7

I6

I5

I4

I3

I2

I1

R/W

A14

A13

A12

A11

A10

A9

A8

A7

A6

A5

A4

A3

A2

A1

A0

Table 38. Serial Control Port Timing

Parameter

Description

t_DS

Setup time between data and the rising edge of SCLK

Hold time between data and the rising edge of SCLK

Period of the clock

t_DH

t_SCLK

t_S

Setup time between the CS falling edge and the SCLK rising edge (start of the communication cycle)

Setup time between the SCLK rising edge and CS rising edge (end of the communication cycle)

Minimum period that SCLK should be in a logic high state

t_C

t_HIGH

t_LOW

t_DV

Minimum period that SCLK should be in a logic low state

SCLK to valid SDIO (see Figure 36)

CS

DON'T CARE

SCLK

SDIO

DON'T CARE

R/W A14 A13 A12 A11 A10 A9 A8 A7 A6 A5 A4 A3 A2 A1 A0 D7 D6 D5 D4 D3 D2 D1 D0 D7 D6 D5 D4 D3 D2 D1 D0

16-BIT INSTRUCTION HEADER

REGISTER (N) DATA

REGISTER (N – 1) DATA

Figure 28. Serial Control Port Write—MSB First, Address Decrement, Two Bytes of Data

Rev. A | Page 43 of 65

AD9576

Data Sheet

t_DS

t_HIGH

t_S

t_C

t_SCLK

t_DH

t_LOW

CS

SCLK

SDIO

DON'T CARE

R/W

A14

A13

A12

A11

A10

A9

A8

A7

A6

A5

D4

D3

D2

D1

D0

Figure 29. Timing Diagram for Serial Control Port Write—MSB First

CS

SCLK

t_DV

SDIO

DATA BIT N

DATA BIT N – 1

Figure 30. Timing Diagram for Serial Control Port Register Read—MSB First

CS

DON'T CARE

SCLK

SDIO

DON'T CARE

A0 A1 A2 A3 A4 A5 A6 A7 A8 A9 A10 A11 A12 A13 A14 R/W D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

16-BIT INSTRUCTION HEADER REGISTER (N) DATA REGISTER (N + 1) DATA

DON'T CARE

Figure 31. Serial Control Port Write—LSB First, Address Increment, Two Bytes of Data

t_S

t_C

CS

t_SCLK

t_HIGH

t_LOW

t_DS

SCLK

SDIO

t_DH

BIT N

BIT N + 1

Figure 32. Timing Diagram for Serial Control Port—Write

The AD9576 I²C port consists of a serial data line (SDA) and a

serial clock line (SCL). In an I²C bus system, the AD9576 is

connected to the serial bus (data bus SDA and clock bus SCL) as

a slave device; that is, no clock is generated by the AD9576. The

AD9576 uses direct 16-bit memory addressing instead of more

common 8-bit memory addressing.

I²C SERIAL PORT OPERATION

The I²C interface is popular because it requires only two pins

and easily supports multiple devices on the same bus. Its main

disadvantage is programming speed, which is 400 kbps maximum.

The AD9576 I²C port design uses the I²C fast mode; however, it

supports both the 100 kHz standard mode and 400 kHz fast mode.

The AD9576 allows up to seven unique slave devices to occupy

the I²C bus. These are accessed via a 7-bit slave address

transmitted as part of an I²C packet. Only the device with a

matching slave address responds to subsequent I²C commands.

Table 35 lists the supported device slave addresses.

The AD9576 does not strictly adhere to every requirement in

the original I²C specification. In particular, specifications such

as slew rate limiting and glitch filtering are not implemented.

Therefore, the AD9576 is I²C-compatible, but may not be fully

I²C compliant.

Rev. A | Page 44 of 65

Data Sheet

AD9576

I²C Bus Characteristics

Data Transfer Process

A summary of the various I²C abbreviations appears in Table 39.

The master initiates data transfer by asserting a start condition,

which indicates that a data stream follows. All I²C slave devices

connected to the serial bus respond to the start condition.

Table 39. I²C Bus Abbreviation Definitions

Abbreviation

Definition

Start

The master then sends an 8-bit address byte over the SDA line,

S

W

consisting of a 7-bit slave address (MSB first) plus an R/ bit.

Sr

P

Repeated start

Stop

This bit determines the direction of the data transfer, that is,

whether data is written to or read from the slave device (0 =

write and 1 = read).

A

W

R

Acknowledge

No acknowledge

Write

The peripheral whose address corresponds to the transmitted

address responds by sending an acknowledge bit. All other

devices on the bus remain idle while the selected device waits

Read

W

for data to be read from or written to it. If the R/ bit is 0, the

The transfer of data is shown in Figure 33. One clock pulse is

generated for each data bit transferred. The data on the SDA

line must be stable during the high period of the clock. The

high or low state of the data line can change only when the

clock signal on the SCL line is low.

master (transmitter) writes to the slave device (receiver). If the

W

R/ bit is 1, the master (receiver) reads from the slave device

(transmitter).

The format for these commands is described in the Data

Transfer Format section.

SDA

Data is then sent over the serial bus in the format of nine clock

pulses, one data byte (eight bits) from either master (write

mode) or slave (read mode) followed by an acknowledge bit

from the receiving device. The number of bytes that can be

transmitted per transfer is unrestricted. In write mode, the first

two data bytes immediately after the slave address byte are the

internal memory (control registers) address bytes, with the high

address byte first. This addressing scheme gives a memory

address of up to 2¹⁶− 1 = 65,535. ꢀe data bytes aꢁer these two

memory address bytes are register data written to or read from

the control registers. In read mode, the data bytes after the slave

address byte are register data written to or read from the control

registers.

SCL

DATA LINE

STABLE;

CHANGE

OF DATA

ALLOWED

DATA VALID

Figure 33. Valid Bit Transfer

Start/stop functionality is shown in Figure 33. The start

condition is characterized by a high to low transition on the

SDA line while SCL is high. The master always generates the

start condition to initialize a data transfer. The stop condition is

characterized by a low to high transition on the SDA line while

SCL is high. The master always generates the stop condition to

terminate a data transfer. Every byte on the SDA line must be

eight bits long. Each byte must be followed by an acknowledge

bit; bytes are sent MSB first.

When all the data bytes are read or written, stop conditions are

established. In write mode, the master (transmitter) asserts a stop

condition to end data transfer during the clock pulse following

the acknowledge bit for the last data byte from the slave device

(receiver). In read mode, the master device (receiver) receives

the last data byte from the slave device (transmitter) but does

not pull SDA low during the ninth clock pulse. This is known as

a nonacknowledge bit. By receiving the non-acknowledge bit,

the slave device knows that the data transfer is finished and

enters idle mode. The master then takes the data line low

during the low period before the 10^thclock pulse, and high

during the 10^thclock pulse to assert a stop condition.

The acknowledge bit (A) is the ninth bit attached to any 8-bit

data byte. An acknowledge bit is always generated by the

receiving device (receiver) to inform the transmitter that the

byte has been received. It is done by pulling the SDA line low

during the ninth clock pulse after each 8-bit data byte.

A

The no acknowledge bit ( ) is the ninth bit attached to any 8-bit

data byte. A no acknowledge bit is always generated by the

receiving device (receiver) to inform the transmitter that the

byte has not been received. It is done by leaving the SDA line

high during the ninth clock pulse after each 8-bit data byte.

After issuing a nonacknowledge bit, the AD9576 I²C state

machine goes into an idle state.

A start condition can be used in place of a stop condition.

Furthermore, a start or stop condition can occur at any time,

and partially transferred bytes are discarded.

Rev. A | Page 45 of 65

AD9576

Data Sheet

SDA

SCL

S

P

START CONDITION

STOP CONDITION

Figure 34. Start and Stop Conditions

MSB

SDA

SCL

ACK FROM

SLAVE RECEIVER

ACK FROM

SLAVE RECEIVER

3 TO 7

8

9

3 TO 7

8

9

10

P

1

2

1

2

S

Figure 35. Acknowledge Bit

MSB

SDA

SCL

ACK FROM

SLAVE RECEIVER

ACK FROM

SLAVE RECEIVER

3 TO 7

8

9

3 TO 7

8

9

10

P

1

2

1

2

S

Figure 36. Data Transfer Process (Master Write Mode, 2-Byte Transfer)

SDA

SCL

ACK FROM

NONACK FROM

MASTER RECEIVER

3 TO 7

8

9

3 TO 7

8

9

10

P

1

2

1

2

S

Figure 37. Data Transfer Process (Master Read Mode, 2-Byte Transfer), First Acknowledge From Slave

Rev. A | Page 46 of 65

Data Sheet

AD9576

Data Transfer Format

The write byte format is used to write a register address to the

RAM starting from the specified RAM address.

S

Slave

address

W

A

RAM address high byte

A

RAM address low byte

A

RAM

Data 0

A

RAM

Data 1

A

RAM

Data 2

A

P

The send byte format is used to set up the register address for subsequent reads.

Slave address RAM address high byte

S

W

A

RAM address low byte

A

P

The receive byte format is used to read the data byte(s) from RAM starting from the current address.

Slave address RAM Data 0 RAM Data 1

S

R

A

RAM Data 2

A

The read byte format is the combined format of the send byte and the receive byte.

S

Slave

address

W

A

RAM address

high byte

A

RAM address

low byte

A

Sr Slave

R

A

RAM

Data 0

A

RAM

Data 1

A

RAM

Data 2

A

P

address

I²C Serial Port Timing

SDA

t_LOW

t_R

t_{SU; DAT}

t_BUF

t_{HD; STA}

t_R

t_F

t_SP

t_F

SCL

t_{SU; STO}

t_{SU; STA}

t_{HD; STA}

t_HIGH

t_{HD; DAT}

S

Sr

P

S

Figure 38. I²C Serial Port Timing

Table 40. IꢀC Timing Definitions

Parameter

f_SCL

Description

Serial clock

t_BUF

Bus free time between stop and start conditions

Repeated hold time start condition

Repeated start condition setup time

Stop condition setup time

t_{HD; STA}

t_{SU; STA}

t_{SU; STO}

t_{HD; DAT}

t_{SU; DAT}

t_LOW

Data hold time

Data setup time

SCL clock low period

t_HIGH

SCL clock high period

t_R

Minimum/maximum receive SCL and SDA rise time

Minimum/maximum receive SCL and SDA fall time

t_F

t_SP

Pulse width of voltage spikes that must be suppressed by the input filter

Rev. A | Page 47 of 65

AD9576

Data Sheet

CONTROL REGISTER MAP

Table 41. Register Summary

Address

Default

(Hex)

Register Name Bit 7 (MSB) Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB) (Hex)

R/W

Serial Port Configuration Registers

0x000

0x001

SPI

Soft reset

Single

LSB first

Address

ascension

Reserved

Address

ascension

LSB first

Soft reset

0x00

R/W

Configuration A

SPI

Reserved Read buffer

registers

Reset sans

register map

Reserved

Configuration B instruction

0x003

0x004

0x005

0x006

0x00B

0x00C

0x00D

0x00F

Chip type

Reserved

Chip type

0x05

0x4F

0x01

0x11

0x00

0x56

0x04

R

Product ID1

Serial ID[3:0]

Reserved

R

Product ID2

Serial ID[11:4]

R

Revision

Device version

Device revision

R

SPI version

Vendor ID[7:0]

Vendor ID[15:8]

R

Vendor ID

R

I/O update

Reserved

I/O update 0x00

R/W

Status Indicator Registers

0x020

PLL status

Reserved

PLL0

PLL1 lock

PLL0 lock

detect

0x00

R

calibration in detect

progress

0x021

Reference

Reserved

Reference status

Reserved

Active

reference

REF2 LOR

REF1 LOR

REF0 LOR

Chip Mode Register

0x040 Mode selection

Chip

PLL1

0x02

R/W

power-

down

reference

select

Reference Input Configuration Registers

0x080

Reference

inputs

Reserved

REF1

power-

down

REF1 format

Reserved

REF0 power-

down

REF0 format

0x00

R/W

0x081

Reserved

REF2 power-

down

REF2 format

Reference Switchover Registers

0x082

Reference

switchover

Reserved

Disable

smooth

switchover

Enable XTAL

redundancy

switchover

Enable soft Soft

0x00

R/W

reference

select

reference

select

0x083

Reference

monitor control reference

monitor

Enable

Reserved Monitored Reference

Reference monitor clock

frequency

Error window

frequency

monitor

8 kHz

operation

PLL0 Configuration Registers

0x100

0x101

0x102

PLL0 controls

Reserved

PLL0

calibration

PLL0 sync

PLL0

power-

down

PLL0 reset 0x00

R/W

PLL0

configuration

Reserved

PLL0

doubler

enable

PLL0 loop mode

N0 SDM

power-

down

0x01

0x8D

PLL0 charge

PLL0 charge pump current

pump current

0x103

0x104

PLL0 loop filter

PLL0 RPOLE2 loop filter

PLL0 R_ZEROloop filter

Reserved

PLL0 CPOLE1 loop filter

PLL0 loop

0xE8

0x00

R/W

filter

bypass

0x105

0x107

PLL0 input

divider

Reserved

R0 divider ratio

N0 divider integer value

0x01

0x64

R/W

PLL0 fractional

feedback divider

(integer)

Rev. A | Page 48 of 65

Data Sheet

AD9576

Address

Default

(Hex)

0x108

0x109

0x10A

0x10B

0x10C

0x10D

0x10E

0x10F

0x110

0x111

Register Name Bit 7 (MSB) Bit 6

Bit 5

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB) (Hex)

R/W

PLL0 fractional

feedback divider

(fractional)

N0 divider fractional value

N0 divider modulus value

N0A Divider Ratio

0x00

PLL0 fractional

feedback divider

(modulus)

PLL0 cascaded

feedback divider

Reserved

N0A Divider Ratio[11:8]

Q_ZDdivider ratio

Q_ZDinitial phase

PLL0 zero delay

feedback divider

Reserved

PLL0 VCO Dividers Registers

0x120

0x121

0x122

VCO dividers

control

Reserved

M1 sync

M1 power- M1 reset

down

Reserved

M0 sync

M0 power- M0 reset

down

0x20

0x44

0x00

R/W

VCO dividers

ratios

M1 divider ratio

M0 divider ratio

VCO dividers

sync mask

Reserved

M1 mask M1 mask

sync Q2

M0 mask

sync Q_ZD

M0 mask

sync Q3

M0 mask sync M0 mask

Q2 sync Q1

M0 mask

sync Q0

sync Q1

PLL0 Distribution Registers

0x140

Q0 divider

Q0

Q0 divider ratio

0x03

R/W

power-

down

0x141

0x142

Reserved

Q0 initial phase

0x00

R/W

Channel 0

driver config-

uration

Reserved

OUT0 power-

down

OUT0 driver format

OUT1 driver format

OUT2 driver format

OUT3 driver format

0x143

0x144

0x145

0x146

Channel 1

driver config-

uration

Reserved

OUT1 power-

down

0x00

0x03

R/W

Channel 2

driver config-

uration

OUT2 power-

down

Channel 3

driver config-

uration

OUT3 power-

down

Q1 divider

Reserved

Q1

power-

down

Q1 divide ratio

0x147

0x148

Q1 source

Q1 initial phase

OUT4 power-

0x00

R/W

Channel 4

driver config-

uration

Reserved

OUT4 driver format

OUT5 driver format

down

0x149

0x14A

Channel 5

driver config-

uration

OUT5 power-

down

0x00

0x03

R/W

Q2 Divider

Reserved

Q2

power-

down

Q2 divide ratio

0x14B

0x14C

Q2 source

Q2 initial phase

OUT6 power-

0x00

R/W

Channel 6

driver config-

uration

Reserved

OUT6 driver format

OUT7 driver format

down

0x14D

Channel 7

driver config-

uration

OUT7 power-

down

0x00

R/W

Rev. A | Page 49 of 65

AD9576

Data Sheet

Address

Default

(Hex)

Register Name Bit 7 (MSB) Bit 6

Bit 5

Reserved

Bit 4

Bit 3

Bit 2

Bit 1

Bit 0 (LSB) (Hex)

R/W

PLL1 Configuration Registers

0x200

PLL1 controls

PLL1 sync

PLL1

power-

down

PLL1 reset 0x00

0x10

R/W

0x201

0x202

PLL1 feedback

divider

N1 divider ratio

R/W

PLL1 input

dividers

Reserved

R1 divider ratio

PLL1

0x01

doubler

enable

PLL1 Distribution Registers

0x240

Q3 divider

Reserved

Q3

Q3 divider ratio

0x83

R/W

power-

down

0x241

0x242

OUT89

source

Q3

source

Q3 initial phase

0x00

0xC1

R/W

Channel 8

driver config-

uration

OUT8 CMOS

enable full

swing

OUT8 driver format

OUT9 driver format

OUT8 CMOS polarity

OUT8 drive OUT8

strength enable

0x243

0x244

Channel 9

driver config-

uration

OUT9 CMOS

enable full

swing

OUT9 CMOS polarity

Q4 divider ratio

OUT9 drive OUT9

0xC1

0x83

R/W

strength

enable

Q4 divider

Reserved

Q4

power-

down

0x245

0x246

Reserved

OUT10

source

Q4 initial phase

0x80

0xC1

R/W

Channel 10

driver

OUT10

CMOS

OUT10 driver format

OUT10 CMOS polarity

OUT10

drive

OUT10

enable

configuration

enable full

swing

strength

Rev. A | Page 50 of 65

Data Sheet

AD9576

CONTROL REGISTER DESCRIPTIONS

SERIAL PORT CONFIGURATION REGISTERS (REGISTER 0x000 TO REGISTER 0x00F)

Table 42. Serial Port Configuration Registers

Address Bits Bit Name

Settings Description

Mirror of Bit 0.

Reset Access

0x000

7

6

5

Soft reset

LSB first

0x0

R/W

Mirror of Bit 1.

Address

Mirror of Bit 2.

ascension

[4:3] Reserved

Reserved.

0x0

R

2

Address

ascension

This bit determines how the register address pointer is automatically 0x0

changed in a multibyte transfer.

R/W

0

1

Decrement.

Increment.

1

LSB first

This bit determines the bit order for data readback. This bit has no

effect in I²C mode.

0x0

R/W

0

1

Serial data stream starts with the LSB.

Serial data stream starts with the MSB.

0

7

Soft reset

This bit issues a chip level reset. This bit is autoclearing.

0x0

R/W

0x001

Single instruction

This bit disables streaming operation. For SPI transfers, this bit forces

each data byte to be preceded by a new instruction.

6

5

Reserved

Reserved.

0x0

R/W

Read buffer

registers

This bit specifies the data source for serial port read commands.

[4:3] Reserved

Reserved.

0x0

R

2

Reset sans

This bit issues a chip level reset, but does not reset register map values.

R/W

register map

0

1

Normal operation.

Chip held in reset.

[1:0] Reserved

[7:4] Reserved

[3:0] Chip type

[7:4] Serial ID[3:0]

Reserved.

0x0

0x5

R

0x003

0x004

Reserved.

These bits are the unique identifier for the type of device.

These bits are a unique identifier, when combined with chip type, for 0x4

an individual device supporting the Analog Devices serial control

interface standard.

[3:0] Reserved

Reserved.

0xF

R

0x005

0x006

[7:0] Serial ID[11:4]

These bits are a unique identifier, when combined with chip type, for 0x1

an individual device supporting the Analog Devices serial control

interface standard.

[7:4] Device version

[3:0] Device revision

[7:0] SPI version

These bits indicate the silicon variant of the device

These bits indicate the silicon revision of the device.

0x1

0x0

R

0x00B

0x00C

0x00D

0x00F

These bits indicate the version of the analog devices serial control

interface standard implemented on the device.

[7:0] Vendor ID[7:0]

[7:0] Vendor ID[15:8]

[7:1] Reserved

These bits are the unique vendor ID and are reflective of the Analog

Devices allocated USB vendor ID.

0x56

0x4

R

These bits are the unique vendor ID and are reflective of the Analog

Devices allocated USB vendor ID.

Reserved.

0x0

R

0

I/O update

This bit initiates a transfer of the buffered registers to the active

registers. This is an autoclearing bit.

R/W

Rev. A | Page 51 of 65

AD9576

Data Sheet

STATUS INDICATOR REGISTERS (REGISTER 0x020 TO REGISTER 0x021)

Table 43. Status Indicator Registers

Address Bits Bit Name

0x020 [7:3] Reserved

Settings Description

Reset Access

Reserved.

0x0

R

2

1

0

PLL0 calibration in

progress

This bit indicates the status of the PLL0 VCO calibration.

0

1

PLL normal operation.

VCO calibration active.

PLL1 lock detect status.

Unlocked.

PLL1 lock detect

0x0

R

0

1

Locked.

PLL0 lock detect

PLL0 lock detect status.

Unlocked.

0

1

Locked.

0x021

[7:6] Reserved

Reserved.

R

[5:4] Reference status

PLL0 active reference frequency indicator. If the reference monitor 0x0

is Inactive, this bit field indicates the relationship between the

requested reference input and the currently active reference.

00

11

Agreement.

Disagreement.

If the reference monitor is active, the following settings apply:

00

01

10

11

Valid.

Slow.

Fast.

Indeterminate fault.

3

2

1

0

Active reference

REF2 LOR

PLL0 active reference indicator.

REF0.

0x0

R

0

1

REF1.

Reference status indicator.

Reference present.

Loss of reference.

0

1

REF1 LOR

Reference status indicator.

Reference present.

Loss of reference.

0

1

REF0 LOR

Reference status indicator.

Loss of reference.

1

0

Reference present.

CHIP MODE REGISTER (REGISTER 0x040)

Table 44. Chip Mode Register

Address

Bits

[7:2]

1

Bit Name

Settings

Description

Reset

Access

R

0x040

Reserved

Reserved.

0x0

0x1

Chip power-down

Chip level power-down control.

R/W

0

1

Enabled.

Powered down.

0

PLL1 reference select

This bit determines the PLL1 reference input source.

0x0

R/W

0

1

PLL0 active reference.

REF2.

Rev. A | Page 52 of 65

Data Sheet

AD9576

REFERENCE INPUT CONFIGURATION REGISTERS (REGISTER 0x080 TO REGISTER 0x081)

Table 45. Reference Input Configuration Registers

Address

Bits

7

Bit Name

Settings

Description

Reset

0x0

Access

R

0x080

Reserved

Reserved.

6

REF1 power-down

Input receiver power-down control.

Normal operation.

Powered down.

0x0

R/W

0

1

[5:4]

REF1 format

Input receiver format.

CMOS (V_{DD_x}swing).

AC-coupled differential.

XTAL.

0x0

R/W

00

01

10

11

Reserved.

3

2

Reserved

Reserved.

0x0

R

REF0 power-down

Input receiver power-down control.

Powered down.

R/W

1

0

Normal operation.

Input receiver format.

CMOS (V_{DD_x}swing).

AC-coupled differential.

XTAL.

[1:0]

REF0 format

0x0

R/W

00

01

10

11

Reserved.

0x081

[7:3]

2

Reserved

Reserved.

0x0

R

REF2 power-down

Input receiver power-down control.

Powered down.

R/W

1

0

Normal operation.

Input receiver format.

CMOS (V_{DD_x}swing).

AC-coupled differential.

XTAL.

[1:0]

REF2 format

0x0

R/W

00

01

10

11

Reserved.

Rev. A | Page 53 of 65

AD9576

Data Sheet

REFERENCE SWITCHOVER REGISTERS (REGISTER 0x082 TO REGISTER 0x083)

Table 46. Reference Switchover Registers

Address Bits Bit Name

0x082 [7:4] Reserved

Settings Description

Reset Access

Reserved.

0x0

R

3

Disable smooth

This bit sets the reference switchover mode.

R/W

switchover

0

1

Bounded phase transient.

Immediate.

2

1

Enable XTAL

redundancy switchover

This bit requires the reference monitor to be enabled and both

REF0 and REF1 to be configured as XTAL inputs.

0x0

R/W

Enable soft reference

select

This bit establishes the control source of the PLL0 reference

input mux select line. Not applicable when XTAL redundancy

switchover is enabled.

0

1

REF_SEL pin (Pin 3).

Soft reference select (Register 0x082, Bit 0).

0

7

Soft reference select

This bit controls the PLL0 reference input mux select line.

Applicable only when the enable soft reference select = 1.

0x0

R/W

0

1

REF0 select.

REF1 select.

0x083

Enable reference

monitor

The REF2 input clock serves as the reference monitor frequency 0x0

reference.

6

5

Reserved

Reserved.

0x0

R

Monitored frequency

This bit determines the frequency being monitored by the

reference monitor.

R/W

0

1

REF0 and REF1 input frequency is 25 MHz.

REF0 and REF1 input frequency is 19.44 MHz.

4

Reference monitor

8 kHz operation

This bit configures the reference monitor for an 8 kHz frequency

reference and overrides the reference monitor clock frequency

bit field (Register 0x083, Bits[3:2]).

0x0

R/W

[3:2] Reference monitor

clock frequency

These bits designate the reference monitor frequency reference 0x0

carrier.

00

01

10

11

10 MHz.

19.44 MHz.

25 MHz.

38.88 MHz.

[1:0] Error window

These bits set the frequency tolerance for a reference monitor

decision.

0x0

R/W

00

01

10

11

10 ppm.

25 ppm.

50 ppm.

100 ppm.

Rev. A | Page 54 of 65

Data Sheet

AD9576

PLL0 CONFIGURATION REGISTERS (REGISTER 0x100 TO REGISTER 0x111)

Table 47. PLL0 Configuration Registers

Address Bits Bit Name

0x100 [7:4] Reserved

Settings

Description

Reset Access

Reserved.

0x0

R

3

PLL0 calibration

This bit issues a manual VCO calibration on a low to high

transition.

R/W

2

PLL0 sync

This bit issues a distribution sync command to the dividers

driven by PLL0.

0x0

R/W

0

1

Normal operation.

Dividers held in sync.

PLL0 power-down control.

Normal operation.

1

0

PLL0 power-down

PLL0 reset

0x0

R/W

0

1

Powered down.

PLL0 reset control.

0

1

Normal operation.

Reset.

0x101

[7:4] Reserved

Reserved.

0x0

R

3

PLL0 doubler enable

This bit selects the PLL0 input divider path used.

R0 divider output.

R/W

0

1

×2.

[2:1] PLL0 loop mode

These bits select the PLL0 feedback path.

Loop Mode 0 (single feedback divider).

Loop Mode 1 (cascaded feedback dividers).

Loop Mode 2 (fixed delay divider).

Reserved.

0x0

0x1

R/W

00

01

10

11

0

N0 SDM power-down

N0 SDM power-down control

Normal operation.

0

1

Powered down.

0x102

0x103

[7:0] PLL0 charge pump

current

These bits control the magnitude of the PLL0 charge pump 0x8D

current.

R/W

Total current (µA) = 4 × the bit field value.

[7:6] PLL0 RPOLE2 loop filter

Internal loop filter Pole 2 resistor setting.

0x3

00

01

10

11

2000 Ω.

666 Ω.

400 Ω.

285 Ω.

[5:3] PLL0 R_ZEROloop filter

Internal loop filter zero resistor setting.

0x5

R/W

000

001

010

011

100

101

110

111

1500 Ω.

1875 Ω.

2250 Ω.

2650 Ω.

3000 Ω.

3375 Ω.

3750 Ω.

4125 Ω.

[2:0] PLL0 CPOLE1 loop filter

Internal loop filter Pole 1 capacitor setting.

0x0

R/W

000

001

010

011

100

101

110

111

2 pF.

8 pF.

42 pF.

48 pF.

82 pF.

88 pF.

122 pF.

128 pF.

Rev. A | Page 55 of 65

AD9576

Data Sheet

Address Bits Bit Name

Settings

Description

Reset Access

0x104

[7:1] Reserved

Reserved.

0x0

0x1

R

0

PLL0 loop filter bypass

This bit bypasses the internal loop filter.

Reserved.

R/W

R

0x105

[7:6] Reserved

[5:0] R0 divider ratio

PLL0 reference input divide ratio.

Reserved.

R/W

0

1 to 63

Divide ratio = bit field value.

0x107

[7:0] N0 divider integer value

These bits set the operating divide ratio. Divide ratio = bit

field value.

0x64

R/W

0 to 11

Invalid.

12 to 14

15 to 252

Valid if the SDM is disabled.

Valid.

253 to 255 Valid if the SDM is disabled.

These bits set the SDM fractional value, Bits[7:0].

0x108

0x109

0x10A

0x10B

[7:0] N0 divider fractional value

0x0

R/W

[7:0]

These bits set the SDM fractional value, Bits[15:8].

These bits set the SDM fractional value, Bits[23:16].

[7:0]

[7:0] N0 divider modulus value

These bits set the SDM modulus value, Bits[7:0]. These bits

must be greater than fractional value.

0x10C

0x10D

0x10E

[7:0]

These bits set the SDM modulus value, Bits[15:8]. These bits 0x0

must be greater than fractional value.

R/W

[7:0]

These bits set the SDM modulus value, Bits[23:16]. These

bits must be greater than fractional value.

0x0

[7:0] N0A Divider Ratio[7:0]

These bits set the operating divide ratio. Divide ratio = bit

field value.

0x0

0 to 3

Invalid.

Valid.

4 to 4095

0x10F

[7:4] Reserved

Reserved.

0x0

R

[3:0] N0A Divider Ratio[11:8]

These bits set the operating divide ratio. Divide ratio = bit

field value.

R/W

0 to 3

Invalid.

4 to 4095

Valid.

0x110

0x111

[7:6] Reserved

Reserved.

0x0

R

[5:0] Q_ZDdivider ratio

PLL0 fixed delay feedback divider ratio.

Divide ratio = bit field value + 1.

Reserved.

R/W

[7:6] Reserved

0x0

R

[5:0] Q_ZDinitial phase

PLL0 fixed delay feedback divider static phase offset.

Phase offset in units of half cycles of the input clock.

R/W

Rev. A | Page 56 of 65

Data Sheet

AD9576

PLL0 VCO DIVIDERS REGISTERS (REGISTER 0x120 TO REGISTER 0x122)

Table 48. PLL0 VCO Dividers Registers

Address Bits Bit Name

Settings Description

Reset Access

0x120

7

6

Reserved

M1 sync

Reserved.

0x0

R

This bit issues a distribution sync command to the dividers

R/W

driven by M1.

0

1

Normal operation.

Dividers held in reset.

Divider power-down control.

Normal operation.

Powered down.

5

4

M1 power-down

M1 reset

0x1

0x0

R/W

0

1

Divider reset control

Normal operation.

Divider held in reset.

Reserved.

0

1

3

2

Reserved

M0 sync

0x0

R

This bit issues a distribution sync command to the dividers

driven by M0.

R/W

0

1

Normal operation.

Dividers held in reset.

1

0

M0 power-down

M0 reset

Divider power-down control.

Normal operation.

0x0

0x4

R/W

0

1

Powered down.

Divider reset control

0

1

Normal operation.

Divider held in reset.

0x121

[7:4] M1 divider ratio

[3:0] M0 divide ratio

Sets operating divide ratio.

0 to 1

Powered down.

2 to 11

12 to 15

Divide = bit field value.

Powered down.

These bits set the operating divide ratio.

Powered down.

0x4

R/W

0 to 1

2 to 11

12 to 15

Divide = bit field value.

Powered down.

0x122

7

6

5

4

3

2

1

0

Reserved

Reserved.

0x0

R

M1 mask sync Q2

M1 mask sync Q1

M0 mask sync Q_ZD

M0 mask sync Q3

M0 mask sync Q2

M0 mask sync Q1

M0 mask sync Q0

This bit sets the Divider Q2 ignore and M1 sync signal flag.

This bit sets the Divider Q1 ignore and M1 sync signal flag.

This bit sets the Divider Q_ZDignore and M0 sync signal flag.

This bit sets the Divider Q3 ignore and M0 sync signal flag.

This bit sets the Divider Q2 ignore and M0 sync signal flag.

This bit sets the Divider Q1 ignore and M0 sync signal flag.

This bit sets the Divider Q0 ignore and M0 sync signal flag.

R/W

Rev. A | Page 57 of 65

AD9576

Data Sheet

PLL0 DISTRIBUTION REGISTERS (REGISTER 0x140 TO REGISTER 0x14D)

Table 49. PLL0 Distribution Registers

Address Bits Bit Name

Settings Description

Reset Access

0x140

7

6

Reserved

Reserved.

0x0

R

Q0 power-down

Divider power-down control.

R/W

0

1

Normal operation.

Powered down.

[5:0] Q0 divider ratio

[7:6] Reserved

These bits set the operating divide ratio. Divide ratio = bit field value + 1. 0x3

R/W

R

0x141

0x142

Reserved.

0x0

[5:0] Q0 initial phase

These bits set the divider static phase offset. The phase offset is in

units of half cycles of the input clock.

R/W

[7:3] Reserved

Reserved.

0x0

R

2

OUT0 power-down

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT0 driver format

These bits select the driver format of OUT0.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

0x143

0x144

0x145

0x146

[7:3] Reserved

OUT1 power-down

Reserved.

0x0

R

2

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT1 driver format

These bits select the driver format of OUT1.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

[7:3] Reserved

OUT2 power-down

Reserved.

0x0

R

2

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT2 driver format

These bits select the driver format of OUT2.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

[7:3] Reserved

OUT3 power-down

Reserved.

0x0

R

2

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT3 driver format

These bits select the driver format of OUT3.

LVDS 3.5 mA.

0x0

R/W

00

01

10

11

LVDS 4.2 mA.

HSTL 8 mA.

1.8 V CMOS.

7

6

Reserved

Reserved.

0x0

R

Q1 power-down

Divider power-down control.

Normal operation.

Powered down.

R/W

0

1

[5:0] Q1 divide ratio

These bits set the operating divide ratio. Divide ratio = bit field value + 1. 0x3

R/W

Rev. A | Page 58 of 65

Data Sheet

AD9576

Address Bits Bit Name

Settings Description

Reset Access

0x147

7

6

Reserved

Q1 source

Reserved.

0x0

R

This bit selects the divider input clock.

M0 output.

R/W

0

1

M1 output.

[5:0] Q1 initial phase

[7:3] Reserved

These bits set the divider static phase offset. The phase offset is in

units of half cycles of the input clock.

0x0

R/W

0x148

Reserved.

0x0

R

2

OUT4 power-down

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT4 driver format

These bits select the driver format of OUT4.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

0x149

[7:3] Reserved

OUT5 power-down

Reserved.

0x0

R

2

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT5 driver format

These bits select the driver format of OUT5.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

0x14A

0x14B

7

6

Reserved

Reserved.

0x0

R

Q2 power-down

Divider power-down control.

Normal operation.

Powered down.

R/W

0

1

[5:0] Q2 divide ratio

These bits set the operating divide ratio. Divide ratio = bit field value + 1. 0x3

R/W

R

7

6

Reserved

Q2 source

Reserved.

0x0

This bit selects the divider input clock.

M0 output.

R/W

0

1

M1 output.

[5:0] Q2 initial phase

[7:3] Reserved

These bits set the divider static phase offset. The phase offset is in

units of half cycles of the input clock.

0x0

R/W

0x14C

Reserved.

0x0

R

2

OUT6 power-down

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT6 driver format

These bits select the driver format of OUT6.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

0x14D

[7:3] Reserved

OUT7 power-down

Reserved.

0x0

R

2

Driver power-down control.

Normal operation.

Powered down.

R/W

0

1

[1:0] OUT7 driver format

These bits select the driver format of OUT7.

LVDS, 3.5 mA.

0x0

R/W

00

01

10

11

LVDS, 4.2 mA.

HSTL, 8 mA.

1.8 V CMOS.

Rev. A | Page 59 of 65

AD9576

Data Sheet

PLL1 CONFIGURATION REGISTERS (REGISTER 0x200 TO REGISTER 0x202)

Table 50. PLL1 Configuration Registers

Address Bits Bit Name

Settings Description

Reset Access

0x200

[7:3] Reserved

Reserved.

0x0

R

2

1

0

PLL1 sync

Issues a distribution sync command to dividers driven by PLL1.

R/W

0

1

Normal operation.

Dividers held in sync.

PLL1 power-down

PLL1 reset

PLL power-down control.

0x0

R/W

0

1

Normal operation.

Power down.

PLL reset control.

0x0

0

1

Normal operation.

PLL1 held in reset.

0x201

0x202

[7:0] N1 divider ratio

These bits set the operating divide ratio. Divide value = bit field value.

0x10

0 to 3

Invalid values.

4 to 255

Valid values.

[7:4] Reserved

Reserved.

0x0

R

[3:1] R1 divider ratio

PLL1 reference input divider.

R/W

0

Power down.

1

÷1.

10

÷1.5.

11

÷2.

100

101

110

111

÷3.

÷4.

÷6.

÷8.

0

PLL1 doubler enable

This bit selects the PLL1 input divider path used.

0x1

R/W

0

1

R1 divider output.

×2.

PLL1 DISTRIBUTION REGISTERS (REGISTER 0x240 TO REGISTER 0x246)

Table 51. PLL1 Distribution Registers

Address Bits Bit Name

Settings Description

Reserved. Always configure this bit to the default value.

Reset Access

0x240

7

6

Reserved

0x1

0x0

R/W

Q3 power-down

Divider power-down control.

Normal operation.

0

1

Powered down.

[5:0] Q3 divider ratio

These bits set the operating divide ratio. Divide ratio = bit field

value + 1.

0x3

0x0

R/W

0x241

7

OUT89 source

This bit selects the OUT8 and OUT9 input clock.

Q3 divider output.

0

1

PLL1 active reference.

6

OUT10 source

This bit selects the divider input clock.

PLL1 output.

0x0

R/W

0

1

M0 output.

[5:0] Q3 initial phase

These bits select the divider static phase offset. The phase offset is

in units of half cycles of the input clock.

Rev. A | Page 60 of 65

Data Sheet

AD9576

Address Bits Bit Name

Settings Description

This bit determines the full swing of the OUT8 CMOS driver. Set this

Reset Access

0x242

7

OUT8 CMOS

0x1

R/W

enable full swing

bit only if the associated output format is configured as CMOS.

0

1

1.8 V swing.

Full swing.

[6:4] OUT8 driver format

These bits select the driver format of OUT8.

0x4

R/W

000

001

010

011

100

101

110

111

Tristate.

HSTL.

LVDS.

HCSL.

CMOS (both outputs active).

CMOS (positive output only).

CMOS (negative output only).

Reserved.

[3:2] OUT8 CMOS

polarity

These bits set the polarity of the full swing CMOS output driver.

Noninverted, inverted.

Inverted, inverted.

0x0

R/W

00

01

10

11

Noninverted, noninverted.

Inverted, noninverted.

1

OUT8 drive

strength

This bit selects the drive strength of the OUT8 driver and is only

applicable when the output format is configured as LVDS or full

swing CMOS.

0

1

CMOS—nominal drive; LVDS—3.5 mA.

CMOS—low drive; LVDS—4.5 mA.

Output driver enable control.

Power down.

0

7

OUT8 enable

0x1

R/W

0

1

Enable.

0x243

OUT9 CMOS

enable full swing

This bit determines the swing of the OUT9 CMOS driver. Set this bit

only if the associated output format is configured as CMOS.

0

1

1.8 V swing.

Full swing.

[6:4] OUT9 driver

format

These bits select the driver format of OUT9.

0x4

R/W

000

001

010

011

100

101

110

111

Tristate.

HSTL.

LVDS.

HCSL.

CMOS (both outputs active).

CMOS (positive output only).

CMOS (negative output only).

Reserved.

[3:2] OUT9 CMOS

polarity

These bits set the polarity of the full swing CMOS output driver.

Noninverted, inverted.

Inverted, inverted.

0x0

R/W

00

01

10

11

Noninverted, noninverted.

Inverted, noninverted.

1

0

OUT9 drive

strength

This bit selects the drive strength of the OUT9 driver and is only applic-

able when the output format is configured as LVDS or full swing CMOS.

0x0

0x1

R/W

0

1

CMOS—nominal drive; LVDS—3.5 mA.

CMOS—low drive; LVDS—4.5 mA.

Output driver enable control.

Power down.

OUT9 enable

0

1

Enable.

Rev. A | Page 61 of 65

AD9576

Data Sheet

Address Bits Bit Name

Settings Description

Reserved. Always configure this bit to the default value.

Reset Access

0x244

7

6

Reserved

0x1

0x0

R/W

Q4 power-down

Divider power-down control.

0

1

Normal operation (default). The Q4 divider works normally.

Powered down. The Q0 divider is powered down.

[5:0] Q4 divider ratio

These bits set the operating divide ratio. Divide ratio = bit field value + 1. 0x3

R/W

0x245

7

6

Reserved

Q4 source

Reserved. Always configure this bit to the default value.

This bit selects the OUT10 input clock source.

PLL1 selected reference input.

0x1

0x0

1

0

Divider, Q4, output.

[5:0] Q4 initial phase

These bits set the divider static phase offset. The phase offset in

units of half cycles of the input clock.

0x0

0x1

R/W

0x246

7

OUT10 CMOS

This bit determines the full swing of the OUT10 CMOS driver. Only

set this bit if the associated output format is configured as CMOS.

enable full swing

0

1

1.8 V swing.

Full swing.

[6:4] OUT10 driver

format

These bits select the driver format of OUT10.

0x4

R/W

000

001

010

011

100

101

110

111

Tristate.

HSTL.

LVDS.

HCSL.

CMOS (both outputs active).

CMOS (positive output only).

CMOS (negative output only).

Reserved.

[3:2] OUT10 CMOS

polarity

These bits set the polarity of the full swing CMOS output driver.

Noninverted, inverted.

Inverted, inverted.

0x0

R/W

00

01

10

11

Noninverted, noninverted.

Inverted, noninverted.

1

0

OUT10 drive

strength

This bit selects the drive strength of the OUT10 driver and is only

applicable when the output format is configured as LVDS or full

swing CMOS.

0x0

0x1

R/W

0

1

CMOS—nominal drive; LVDS—3.5 mA.

CMOS—low drive; LVDS—4.5 mA.

Output driver enable control.

Power down.

OUT10 enable

0

1

Enable.

Rev. A | Page 62 of 65

Data Sheet

AD9576

APPLICATIONS INFORMATION

INTERFACING TO CMOS CLOCK OUTPUTS

INTERFACING TO LVDS AND HSTL CLOCK

OUTPUTS

Apply the following general guidelines when using the single-

ended 1.8 V or 3.3 V CMOS clock output drivers.

LVDS and HSTL both employ a differential output driver. The

recommended termination circuit for LVDS and HSTL drivers

Design point to point nets such that a driver has only one

receiver on the net, if possible. This allows simple termination

schemes and minimizes ringing due to possible mismatched

impedances on the net. Series termination at the source is

generally required to provide transmission line matching and/or

to reduce current transients at the driver.

appears in Figure 41.

3.3V

100ꢀ

50ꢀ

10ꢀ

CMOS

5pF

The value of the series termination depends on the board

design and timing requirements (typically 10 Ω to 100 Ω).

CMOS outputs are limited in terms of the capacitive load or

trace length that they can drive. Typically, trace lengths less

than 6 inches are recommended to preserve signal rise/fall

times and signal integrity.

Figure 41. CMOS Output with Far End Termination

See the AN-586 Application Note for more information about

LVDS.

INTERFACING TO HCSL CLOCK OUTPUTS

60.4ꢀ

HCSL uses a differential open-drain architecture. The open-

drain architecture necessitates the use of an external termination

resistor. Figure 42 shows the typical method for interfacing to

HCSL drivers.

1.0 INCH

10ꢀ

CMOS

MICROSTRIP

5pF

GND

INDEPENDENT

UNCOUPLED 50ꢀ

Figure 39. Series Termination of CMOS Output

TRANSMISSION LINES

HCSL

Termination at the far end of the PCB trace is a second option.

The CMOS outputs of the AD9576 do not supply enough current

to provide a full voltage swing with a low impedance resistive,

far end termination, as shown in Figure 40. Ensure that the

impedance of the far end termination network matches the PCB

trace impedance and provides the desired switching point. The

reduced signal swing may still meet receiver input requirements

in some applications. This can be useful when driving long

trace lengths on less critical nets.

RECEIVER

50ꢀ

Figure 42. HCSL Output Termination

In some cases, the fast switching capability of HCSL drivers

results in overshoot and ringing. The alternative HCSL interface

shown in Figure 43 can mitigate this problem via a small series

resistor, typically in the 10 Ω to 30 Ω range.

INDEPENDENT

UNCOUPLED 50ꢀ

TRANSMISSION LINES

INDEPENDENT

UNCOUPLED 50ꢀ

TRANSMISSION LINES

HCSL

100ꢀ

10ꢀ TO 30ꢀ

HSTL/LVDS

DRIVER

RECEIVER

50ꢀ

Figure 40. LVDS or HSTL Output Termination

Figure 43. Alternate HCSL Output Termination

Rev. A | Page 63 of 65

AD9576

Data Sheet

beads with approximately 75 Ω impedance at 100 MHz are

POWER SUPPLY

suitable for use with Pin 52 and Pin 57.

The AD9576 requires a power supply of 2.5 V 5% or 3.3 V

10%. The Specifications section gives the performance expected

from the AD9576 with the power supply voltage within this

range. The absolute maximum range of −0.3 V to +3.6 V, with

respect to GND, must never be exceeded on the VDD_x pins.

The layout of the AD9576 evaluation board is a good example

of how to route power supply traces and where to place bypass

capacitors and ferrite beads.

The exposed metal pad on the AD9576 package is an electrical

connection, as well as a thermal enhancement. For the device to

function properly, the pad must be properly attached to ground

(GND). The PCB acts as a heat sink for the AD9576; therefore,

this GND connection provides a good thermal path to a larger

heat dissipation area, such as a ground plane on the PCB.

Follow good engineering practice in the layout of power supply

traces and the ground plane of the PCB. Bypass the power

supply on the PCB with adequate capacitance (>10 µF). Bypass

the AD9576 with adequate capacitors (0.1 µF) at all power pins

as close as possible to the device.

In addition to these bypass capacitors, the AD9576 evaluation

board uses six ferrite beads between the 2.5 V (or 3.3 V) source

and Pin 29, Pin 35, Pin 41, Pin 46, Pin 52, and Pin 57. Although

these ferrite beads may not be needed for every application, the

use of these ferrite beads is strongly recommended. At a

minimum, include a place for the ferrite beads (as close to the

bypass capacitors as possible) and populate the board with

0402, 0 Ω resistors. By doing so, there is a place for the ferrite

beads, if needed. Ferrite beads with low (<0.7 Ω) dc resistance

and approximately 600 Ω impedance at 100 MHz are suitable

for use with Pin 29, Pin 35, Pin 41, and Pin 46, while ferrite

POWER AND GROUNDING CONSIDERATIONS AND

POWER SUPPLY REJECTION

Many applications seek high speed and performance under

less than ideal operating conditions. In these application

circuits, the implementation and construction of the PCB is as

important as the circuit design. Proper RF techniques must be

used for device selection, placement, and routing, as well as for

power supply bypassing and grounding to ensure optimum

performance.

Rev. A | Page 64 of 65

Data Sheet

AD9576

OUTLINE DIMENSIONS

DETAIL A

(JEDEC 95)

9.10

0.30

0.25

0.18

9.00 SQ

8.90

PIN 1

INDICATOR

PIN 1

49

48

64

IONS

INDICATOR AR EA OP T

1

(SEE DETAIL

A)

0.50

BSC

6.30

6.20 SQ

6.10

EXPOSED

PAD

33

32

16

17

0.45

0.40

0.35

TOP VIEW

END VIEW

BOTTOM VIEW

0.20 MIN

7.50 REF

0.80

0.75

0.70

FOR PROPER CONNECTION OF

THE EXPOSED PAD, REFER TO

THE PIN CONFIGURATION AND

FUNCTION DESCRIPTIONS

0.05 MAX

0.02 NOM

COPLANARITY

SECTION OF THIS DATA SHEET.

0.08

SEATING

PLANE

0.203 REF

COMPLIANT TO JEDEC STANDARDS MO-220-WMMD

Figure 44. 64-Lead Lead Frame Chip Scale Package [LFCSP]

9 mm × 9 mm and 0.75 mm Package Height

(CP-64-17)

Dimensions shown in millimeters

ORDERING GUIDE

Model¹

Temperature Range

Package Description

Package Option

AD9576BCPZ

AD9576BCPZ-REEL7

AD9576/PCBZ

−40°C to +85°C

64-Lead Lead Frame Chip Scale Package [LFCSP]

Evaluation Board

CP-64-17

¹Z = RoHS-Compliant Part.

I²C refers to a communications protocol originally developed by Philips Semiconductors (now NXP Semiconductors).

registered trademarks are the property of their respective owners.

D13993-0-9/18(A)

Rev. A | Page 65 of 65


型号：	AD9576
厂家：	ADI
描述：	Dual PLL, Asynchronous Clock Generator
文件：	总65页 (文件大小：1324K)
中文：	中文翻译
下载：	下载PDF数据表文档文件

AD9576 [ADI]

相关型号：

AD9576BCPZ

AD9576BCPZ-REEL7

AD9577

AD9577-EVALZ

AD9577BCPZ

AD9577BCPZ-R7

AD9577BCPZ-RL

AD9578

AD9578BCPZ

AD9578BCPZ-REEL7

AD95S08KAC

AD95S08KAF