ADM1052 [ADI]
Precision Dual Voltage Regulator Controller; 精密双电压稳压器控制器
| 型号： | ADM1052 |
| 厂家： | 
ADI |
| 描述： | Precision Dual Voltage Regulator Controller |
| 文件： | 总8页 (文件大小：163K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Precision Dual Voltage
Regulator Controller
a
ADM1052
GENERAL DESCRIPTION
FEATURES
The ADM1052 is a dual, precision, voltage regulator controller
intended for power rail generation and active bus termination
on personal computer motherboards. It contains a precision
1.2 V bandgap reference and two channels consisting of con-
trol amplifiers driving external power devices. Each channel has a
shutdown input to turn off amplifier output and “Hiccup Mode”
protection circuitry for the external power device.
Two Independent Controllers on One Chip
Two 2.525 V Outputs
Shutdown Inputs to Control Each Channel
ꢀ2.5% Accuracy Over Line, Load, and Temperature
Low Quiescent Current
Low Shutdown Current
Works with External N-Channel MOSFETs for Low Cost
“Hiccup Mode” Fault Protection
No External Voltage or Current Setting Resistors
Small, 8-Lead SO Package
The ADM1052 operates from a 12 V supply. This gives suffi-
cient headroom for the amplifiers to drive external N-channel
MOSFETs, operating as source-followers, as the external series
pass devices. This has the advantage that N-channel devices are
cheaper than P-channel devices of similar performance, and the
circuit is easier to stabilize than one using P-channel devices in
a common-source configuration.
APPLICATIONS
Desktop Computers
Servers
Workstations
FUNCTIONAL BLOCK DIAGRAM
3.3V
V
CC
CONTROL
AMPLIFIER
100ꢁF
ADM1052
BANDGAP
REFERENCE
FORCE 1
SENSE 1
V
CC
V
OUT1
50ꢁA
2 ꢂ 100ꢁF
SHUTDOWN
CONTROL
SHDN1
HICCUP
COMPARATOR
3.3V
CONTROL
AMPLIFIER
100ꢁF
FORCE 2
SENSE 2
V
CC
V
OUT2
2 ꢂ 100ꢁF
50ꢁA
SHUTDOWN
CONTROL
SHDN2
HICCUP
COMPARATOR
V
CC
POWER-ON
RESET
CLK/DELAY
GENERATOR
CLOCK
OSCILLATOR
GND
REV. A
Information furnished by Analog Devices is believed to be accurate and
reliable. However, no responsibility is assumed by Analog Devices for its
use, nor for any infringements of patents or other rights of third parties
which may result from its use. No license is granted by implication or
otherwise under any patent or patent rights of Analog Devices.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781/329-4700
Fax: 781/326-8703
World Wide Web Site: http://www.analog.com
© Analog Devices, Inc., 2001
ADM1052–SPECIFICATIONS (V = 12 V ꢀ 6%, V = 3.3 V, T = 0ꢃC to 70ꢃC, both channels, unless otherwise
noted. See Test Circuit.)
CC
IN
A
Parameter
Min
Typ
Max
Unit
Test Conditions/Comments
OUTPUT VOLTAGE
Channel 1, Channel 2
2.525
V
SHDN1, SHDN2 Floating
OUTPUT VOLTAGE ACCURACY
Load Regulation
Line Regulation
–2.5
–5
–5
+2.5
+5
+5
%
mV
mV
VIN = 3.0 V to 3.6 V, IOUT = 10 mA to 1 A
VIN = 3.3 V, IOUT = 10 mA to 1 A1
VIN = 3.0 V to 3.6 V, IOUT = 1 A1
CONTROL AMPLIFIER
Control Amplifier Open-Loop Gain
Control Amplifier Slew Rate
Closed-Loop Settling Time
Turn-On Time
100
3
5
dB
V/µs
µs
IO = 10 mA to 2 A
To 90% of Force High Output Level (CL = 470 pF)
5
µs
Sense Input Impedance1
50
10
2
kΩ
V
V
Force Output Voltage Swing, VF (High)
Force Output Voltage Swing, VF (Low)
RL = 10 kΩ to GND
RL = 10 kΩ to VCC
HICCUP MODE
Hiccup Mode Hold-Off Time
Hiccup Mode Threshold
Hiccup Comparator Glitch Immunity
Hiccup Mode On-Time
Hiccup Mode Off-Time
Power-On Reset Threshold
30
60
90
ms
V
µs
ms
ms
V
Figure 2
0.8 × VOUT
100
1.0
40
0.5
20
6
1.5
60
9
SHUTDOWN, SHDN1, SHDN2
Shutdown Input Low Voltage, VIL
Shutdown Input High Voltage, VIH
Supply Current, Normal Operation
Supply Current, Shutdown Mode
0.8
V
V
mA
µA
2.0
2.4
600
4.0
1000
Shutdown Inputs Floating
Both Channels Shut Down
NOTES
1Guaranteed by design.
Specifications subject to change without notice.
–2–
REV. A
ADM1052
ABSOLUTE MAXIMUM RATINGS*
(TA = 25°C unless otherwise noted)
PIN FUNCTION DESCRIPTIONS
Pin
No.
VCC to GND . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14 V
SHDN1, SHDN2 to GND . . . . . . . . –0.3 V to (VCC + 0.3 V)
SENSE1, SENSE2 to GND . . . . . . . . . . . . –0.3 V to +5.5 V
FORCE1, FORCE2 . . . . . . . . Short-Circuit to GND or VCC
Continuous Power Dissipation (TA = 70°C) . . . . . . . 650 mW
8-Lead SOIC . . . . . . . . . . . . (Derate 8.3 mW/
Operating Temperature Range
Commercial (J Version) . . . . . . . . . . . . . . . . . . 0°C to 70°C
Storage Temperature Range . . . . . . . . . . . . –65°C to +150°C
Lead Temperature (Soldering, 10 sec) . . . . . . . . . . . . 300°C
Mnemonic Function
1
FORCE 2
Output of Channel 2 control amplifier to
gate of external N-channel MOSFET.
2
SENSE 2
Input from source of external MOSFET to
inverting input of Channel 2 control
amplifier, via output voltage-setting feed-
back resistor network.
°C above 70°C)
3
SHDN2
Digital Input. Active-low shutdown control
with 50 µA internal pull-up. The output
of Channel 2 control amplifier goes to
ground when SHDN2 is taken low.
*This is a stress rating only and functional operation of the device at these or any
other conditions above those indicated in the operation sections of this specifica-
tion is not implied. Exposure to absolute maximum rating conditions for extended
periods of time may affect reliability.
4
5
GND
Device Ground Pin.
SHDN1
Digital Input. Active-low shutdown control
with 50 µA internal pull-up. The output
of Channel 1 control amplifier goes to
ground when SHDN1 is taken low.
THERMAL CHARACTERISTICS
8-Lead Small Outline Package: JA = 150°C/W
6
SENSE 1
Input from source of external MOSFET
to inverting input of Channel 1 control
amplifier, via output voltage-setting
feedback resistor network.
ORDERING GUIDE
Temperature
Range
Package
Description
Package
Option
Model
7
8
FORCE 1
VCC
Output of Channel 2 control amplifier to
gate of external N-channel MOSFET.
12 V Supply.
ADM1052JR
0°C to 70°C
8-Lead SOIC
SO-8
12V
PIN CONFIGURATION
3.3V
1ꢁF
1
2
3
4
8
7
6
5
V
FORCE 2
CC
V
PHD55N03LT
FORCE 1
100ꢁF
CC
ADM1052
TOP VIEW
(Not to Scale)
SENSE 2
SHDN2
GND
FORCE 1
SENSE 1
SHDN1
V
OUT1
SENSE 1
2 ꢂ 100ꢁF
SHDN1
3.3V
LEAVE OPEN OR
CONNECT TO
LOGIC SIGNALS
IF SHUTDOWN
REQUIRED
ADM1052
100ꢁF
MTD3055VL
FORCE 2
SHDN2
V
OUT2
SENSE 2
GND
2 ꢂ 100ꢁF
Figure 1. Test Circuit
CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily
accumulate on the human body and test equipment and can discharge without detection. Although
the ADM1052 features proprietary ESD protection circuitry, permanent damage may occur on
devices subjected to high-energy electrostatic discharges. Therefore, proper ESD precautions are
recommended to avoid performance degradation or loss of functionality.
WARNING!
ESD SENSITIVE DEVICE
REV. A
–3–
ADM1052–Typical Performance Characteristics
Tek Stop: 25.0MS/s
[
56Acqs
T
]
2.55
2.54
T
2.53
2.52
2.51
T
2v
3v
T
1 t
2.50
B
B
B
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
Ch1 500mV
Ch3 20.0mV
Ch2 20.0mV
M 2.00ꢁs Ch1
W
3.53V
W
W
CURRENT – A
TPC 1. Line Transient Response, Channel 1 and Channel 2
TPC 4. Load Regulation, Channel 1
2.536
2.535
2.534
2.55
2.54
2.53
2.52
2.51
2.533
2.532
2.531
2.530
2.529
2.50
0
0.2
0.4
0.6
0.8
1.0
1.2
1.4
1.6
1.8
2.9
3.0
3.1
3.2
3.3
– V
3.4
3.5
3.6
3.7
CURRENT – A
V
IN
TPC 5. Load Regulation, Channel 2
TPC 2. Line Regulation, Channel 1
0
–10
–20
2.542
2.541
2.540
–30
–40
–50
–60
–70
2.539
2.538
2.537
2.536
2.535
10
100
1k
10k
100k
1M
10M
2.9
3.0
3.1
3.2
3.3
3.4
3.5
3.6
3.7
FREQUENCY – Hz
V
– V
IN
TPC 6. VCC Supply Ripple Rejection
TPC 3. Line Regulation, Channel 2
–4–
REV. A
ADM1052
Tek Stop: Single Seq 50.0MS/s
[
T
]
2.544
2.542
2.540
2.538
1
2.536
2.534
T
2.532
2.530
2.528
B
W
Ch1 20.0mV
M 1.00ꢁs Ch1
–40mV
0
10
20
30
40
50
60
70
80
90
TEMPERATURE – ꢃC
TPC 7. Regulator Output Voltage vs. Temperature
TPC 10. Transient Response Channel 2, 10 mA to 2 A
Output Load Step
Tek Stop: Single Seq 50.0MS/s
Tek Stop: Single Seq 50.0MS/s
[
T
]
[
T
]
T
1
1
T
B
W
B
Ch1 20.0mV
M 1.00ꢁs Ch1
37.6mV
Ch1 20.0mV
M 1.00ꢁs Ch1
–45.0mV
W
TPC 8. Transient Response Channel 1, 10 mA to 2 A
Output Load Step
TPC 11. Transient Response Channel 2, 2 A to 10 mA
Output Load Step
Tek Stop: Single Seq 50.0MS/s
Tek Stop: 10.0kS/s
[
0Acqs
[
T
]
T
]
T
T
1
1
B
B
Ch1 20.0mV
M 1.00ꢁs Ch1
5.2mV
Ch1 10.0mV
M 5.00ꢁs Ch1
800mV
W
W
TPC 9. Transient Response Channel 1, 2 A to 10 mA
Output Load Step
TPC 12. Force Output In Hiccup Mode, Channel 1
REV. A
–5–
ADM1052
“HICCUP MODE” FAULT PROTECTION
GENERAL DESCRIPTION
Hiccup mode fault protection is a simple method of protecting
the external power device without the added cost of external
sense resistors or a current sense pin on the ADM1052. In the
event of a short-circuit condition at the output, the output
voltage will fall. When the output voltage of a channel falls 20%
below the nominal voltage, this is sensed by the hiccup com-
parator and the channel will go into hiccup mode, where the
enable signal to the control amplifier is pulsed on and off with a
1:40 duty cycle.
The ADM1052 is a dual, precision, voltage regulator controller
intended for power rail generation and active bus termination on
personal computer motherboards. It contains a precision 1.2 V
bandgap reference and two channels consisting of control amp-
lifiers driving external power devices. Both channels have an
output of nominally 2.525 V. Each channel has a shutdown
input to turn off amplifier output and protection circuitry for
the external power device.
The ADM1052 operates from a 12 V VCC supply. The output is
disabled until VCC climbs above the reset threshold (6 V–9 V). The
output from the ADM1052 is used to drive external N-channel
MOSFETs, operating as source-followers. This has the advan-
tage that N-channel devices are cheaper than P-channel devices
of similar performance, and the circuit is easier to stabilize than
one using P-channel devices in a common-source configuration.
To prevent the device inadvertently going into hiccup mode
during power-up or during channel enabling, the hiccup mode is
held off for approximately 60 ms on both channels. By this time
the output voltage should have reached its correct value. In the
case of power-up, the hold-off period starts when VCC reaches the
power-on reset threshold of 6 V–9 V. In the case of channel
enabling, the hold-off period starts when SHDN is taken high.
Note that the hold-off timeout applies to both channels even if
only one channel is disabled/enabled.
The external power devices are protected by a “Hiccup Mode”
circuit that operates if the circuit goes out of regulation due to
an output short-circuit. In this case the power device is pulsed
on/off with a 1:40 duty cycle to limit the power dissipation until
the fault condition is removed.
As the 3.3 V input to the drain of the MOSFET is not moni-
tored, it should ideally rise at the same or a faster rate than VCC
At the very least it must be available in time for VOUT to reach its
final value before the end of the power-on delay. If the output
.
CIRCUIT DESCRIPTION
voltage is still less than 80% of the correct value after the power-
on delay, the device will go into hiccup mode until the output
voltage exceeds 80% of the correct value during a hiccup mode
on-period. Of course, if there is a fault condition at the output
during power-up, the device will go into hiccup mode after
the power-up delay and remain there until the fault condition
is removed.
CONTROL AMPLIFIERS
The reference voltage is amplified and buffered by the control
amplifiers and external MOSFETs, the output voltage of each
channel being determined by the feedback resistor network
between the sense input and the inverting input of the con-
trol amplifier.
A power-on reset circuit disables the amplifier output until VCC
has risen above the reset threshold (6 V–9 V).
The effect of power-on delay is illustrated in Figure 2, which
shows an ADM1052 being powered up with a fault condition.
The output current rises to a very high value during the power-
on delay, the device goes into hiccup mode, and the output is
pulsed on and off at 1:40 duty cycle. When the fault condition is
removed, the output voltage recovers to its normal value at the
end of the hiccup mode off period.
Each amplifier output drives the gate of an N-channel power
MOSFET, whose drain is connected to the unregulated supply
input and whose source is the regulated output voltage, which is
also fed back to the appropriate sense input of the ADM1052.
The control amplifiers have high current-drive capability so that
they can quickly charge and discharge the gate capacitance of
the external MOSFET, thus giving good transient response to
changes in load or input voltage.
The load current at which the ADM1052 will go into hiccup
mode is determined by three factors:
• The input voltage to the drain of the MOSFET, VIN
• The output voltage VOUT (–20%)
SHUTDOWN INPUTS
Each channel has a separate shutdown input, which may be
controlled by a logic signal and allows the output of the regula-
tor to be turned on or off. If the shutdown input is held high or
not connected, the regulator operates normally. If the shutdown
input is held low, the enable input of the control amplifier is turned
off and the amplifier output goes low, turning off the regulator.
• The on-resistance of the MOSFET, RON
I
HICCUP = (VIN – (0.8 × VOUT))/RON
It should be emphasized that the hiccup mode is not intended as
a precise current limit but as a simple method of protecting the
external MOSFET against catastrophic fault conditions such as
output short circuits.
–6–
REV. A
ADM1052
POR THRESHOLD
6V – 9V
V
TURN-ON
REF
THRESHOLD
12V SUPPLY
3.3V SUPPLY
TO EXTERNAL
MOSFET DRAIN
MOSFET GATE
THRESHOLD
GATE DRIVE TO
EXTERNAL MOSFET
FAULT
REMOVED
OUTPUT < 0.8 ꢂ V
REG
NORMAL OUTPUT VOLTAGE
CHANNEL 1
OR CHANNEL 2
OUTPUT VOLTAGE
DEVICE
ENTERS
HICCUP MODE
FAULT
CURRENT
HICCUP MODE
HOLD-OFF TIME
CHANNEL 1
OR CHANNEL 2
OUTPUT CURRENT
2 AMPS
OFF
ON
1:40 DUTY CYCLE
Figure 2. Power-On Reset and Hiccup Mode
Similarly, the ground connection to the ADM1052 should be
made as close as possible to the ground of the loads, and the
ground track from the loads to the ADM1052 should not carry
load current. Correct and incorrect layout practice is illustrated
in Figure 3.
APPLICATIONS INFORMATION
PCB LAYOUT
For optimum voltage regulation, the loads should be placed as
close as possible to the source of the output MOSFETs and
feedback to the sense inputs should be taken from a point as
close to the loads as possible. The PCB tracks from the loads
back to the sense inputs should be separate from the output
tracks and not carry any load current.
12V
12V
V
V
CC
CC
FORCE 1
FORCE 1
SENSE 1
SENSE 1
FORCE 2
V
OUT1
V
V
3.3V
IN
IN
FORCE 2
3.3V
I
1
V
SENSE 2
GND
OUT2
SENSE 2
GND
I
2
VOLTAGE DROP
BETWEEN OUTPUT
AND LOAD
I
I
2
1
V
V
OUT2
OUT1
LOAD 1
LOAD 2
LOAD 2
LOAD 1
I
+ I
2
1
VOLTAGE DROP
IN GROUND LEAD
INCORRECT
CORRECT
Figure 3. Correct and Incorrect Layout Practice
REV. A
–7–
ADM1052
12V
In practice, the amount of decoupling required will depend on
the application. PC motherboards are notoriously noisy environ-
ments, and it may be necessary to employ distributed decoupling
to achieve acceptable noise levels on the supply rails.
3.3V
1ꢁF
V
CC
100ꢁF
CHOICE OF MOSFET
FORCE 1
SENSE 1
As previously discussed, the load current at which an output
goes into hiccup mode depends on the on-resistance of the
external MOSFET. If the on-resistance is too low this current
may be very high. While the Test Circuit (Figure 1) shows the
use of the lower resistance PHD55N03LT from Philips on
Channel 1 and the use of the higher resistance MTD3055VL
from Motorola on Channel 2, the MTD3055VL is, in fact,
suitable for both channels. Similarly, the PHB11N06LT from
Philips is also suitable for both channels.
V
OUT1
2 ꢂ 100ꢁF
SHDN1
SHDN2
3.3V
LEAVE OPEN OR
CONNECT TO
LOGIC SIGNALS
IF SHUTDOWN
REQUIRED
ADM1052
100ꢁF
FORCE 2
SENSE 2
THERMAL CONSIDERATIONS
Heat generated in the external MOSFET must be dissipated
and the junction temperature of the device kept within accept-
able limits. The power dissipated in the device is, of course, the
drain-source voltage multiplied by the load current. The required
thermal resistance to ambient is given by
V
OUT2
GND
2 ꢂ 100ꢁF
Figure 4. Typical Application Circuit
SUPPLY DECOUPLING
JA = TJ(MAX) – TAMB(MAX)/(VDS(MAX) × IOUT(MAX))
Surface-mount MOSFETs such as those specified must rely on
heat conduction through the device leads and the PCB. One
square inch of copper (645 sq. mm) gives a thermal resistance of
around 60°C/W for a SOT-223 surface-mount package and
80°C/W for a SO-8 surface-mount package.
The supply to the drain of an external MOSFET should be decoupled
as close as possible to the drain pin of the device, with a 100 µF
capacitor to ground. The output from the source of the MOSFET
should be decoupled as close as possible to the source pin of the
device. Decoupling capacitors should be chosen to have a low
Equivalent Series Resistance (ESR). With the MOSFETs specified
and two 100 µF capacitors in parallel, the circuit will be stable for
load currents up to 2 A. The VCC pin of the ADM1052 should be
decoupled with a 1 µF capacitor to ground, connected as close as
possible to the VCC and GND pins.
For higher power dissipation than can be accommodated by a
surface-mount package D2PAK or TO-220 devices are recom-
mended. These should be mounted on a heatsink with a thermal
resistance low enough to maintain the required maximum junc-
tion temperature.
OUTLINE DIMENSIONS
Dimensions shown in inches and (mm).
8-Lead Small Outline Package
(Narrow Body, SO-8)
0.1968 (5.00)
0.1890 (4.80)
8
1
5
4
0.2440 (6.20)
0.2284 (5.80)
0.1574 (4.00)
0.1497 (3.80)
PIN 1
0.0196 (0.50)
0.0099 (0.25)
0.0500 (1.27)
BSC
ꢂ 45ꢃ
0.0688 (1.75)
0.0532 (1.35)
0.0098 (0.25)
0.0040 (0.10)
SEATING
PLANE
8ꢃ
0ꢃ
0.0500 (1.27)
0.0160 (0.41)
0.0192 (0.49)
0.0138 (0.35)
0.0098 (0.25)
0.0075 (0.19)
–8–
REV. A
相关型号：
©2020 ICPDF网 联系我们和版权申明