CN-0018 [ADI]
Interfacing the ADL5372 I/Q Modulator to the AD9779A Dual-Channel, 1 GSPS High Speed DAC; 在接口ADL5372 I / Q调制器的AD9779A双通道, 1 GSPS高速DAC型号: | CN-0018 |
厂家: | ADI |
描述: | Interfacing the ADL5372 I/Q Modulator to the AD9779A Dual-Channel, 1 GSPS High Speed DAC |
文件: | 总2页 (文件大小:129K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
Circuit Note
CN-0017
Devices Connected/Referenced
Circuit Designs Using Analog Devices Products
Apply these product pairings quickly and with confidence.
For more information and/or support call 1-800-AnalogD
(1-800-262-5643) or visit www.analog.com/circuit.
AD9779A
ADL5371
Dual 16-Bit, 1 GSPS DAC
500 MHz to 1500 MHz I/Q Modulator
Interfacing the ADL5371 I/Q Modulator to the AD9779A
Dual-Channel, 1 GSPS High Speed DAC
a single 50 Ω resistor to ground from each of the DAC outputs
CIRCUIT FUNCTION AND BENEFITS
provides the desired 500 mV dc bias. With just the four 50 Ω
resistors in place, the voltage swing on each pin is 1 V p-p.
This results in a differential voltage swing of 2 V p-p on each
input pair.
This circuit provides a simple, elegant interface between the
ADL5371 I/Q modulator and the AD9779A high speed DAC.
The ADL5371 and the AD9779A are well-matched devices
because they have the same bias levels and similarly high
signal-to-noise ratios (SNR). The matched bias levels of 500 mV
allow for a “glueless” interface—there is no requirement for a
level shifting network that would add noise and insertion loss
along with extra components. The addition of the swing-
limiting resistors (RSLI, RSLQ) allows the DAC swing to be
scaled appropriately without loss of resolution or of the 0.5 V
bias level. The high SNR of each device preserves a high SNR
through the circuit.
By adding resistors RSLI and RSLQ to the interface, the output
swing of the DAC can be reduced without any loss of DAC
resolution. The resistor is placed as a shunt between each side of
the differential pair, as shown in Figure 1. It has the effect of
reducing the ac swing without changing the dc bias already
established by the 50 Ω resistors and the DAC output current.
The value of this ac swing-limiting resistor is chosen based on
the desired ac voltage swing. Figure 2 shows the relationship
between the swing-limiting resistor and the peak-to-peak ac
swing that it produces when 50 Ω bias-setting resistors are used.
Note that all Analog Devices I/Q modulators present a relatively
high input impedance on their baseband inputs (typically >1 kΩ).
As a result, the input impedance of the I/Q modulator will have
no effect on the scaling of the DAC output signal.
CIRCUIT DESCRIPTION
The ADL5371 is designed to interface with minimal
components to members of Analog Devices family of
TxDAC® converters (AD97xx). The baseband inputs of the
ADL5371 require a dc common-mode bias voltage of 500 mV.
With each AD9779A output swinging from 0 mA to 20 mA,
2.0
1.8
1.6
1.4
1.2
1.0
0.8
0.6
0.4
0.2
0
AD9779A
ADL5371
93
92
19
20
OUT1_P
IBBP
RBIP
50Ω
RSLI
100Ω
RBIN
50Ω
OUT1_N
IBBN
QBBN
QBBP
84
83
23
24
OUT2_N
OUT2_P
RBQN
50Ω
RSLQ
100Ω
RBQP
50Ω
10
100
1k
10k
R
(Ω)
L
Figure 1. Interface Between the AD9779A and ADL5371 with 50 Ω Resistors
to Ground to Establish the 500 mV DC Bias for the ADL5371 Baseband Inputs
(Simplified Schematic)
Figure 2. Relationship Between the AC Swing-Limiting Resistor and the
Peak-to-Peak Voltage Swing with 50 Ω Bias-Setting Resistors
Rev. A
“Circuits from the Lab” from Analog Devices have been designed and built by Analog Devices
engineers. Standard engineering practices have been employed in the design and construction of
each circuit, and their function and performance have been tested and verified in a lab environment
at room temperature. However, you are solely responsible for testing the circuit and determining its
suitability and applicability for your use and application. Accordingly, in no event shall Analog
Devices be liable for direct, indirect, special, incidental, consequential or punitive damages due to
anycause whatsoever connectedto the use ofany“Circuit fromthe Lab”. (Continued on last page)
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2008–2009 Analog Devices, Inc. All rights reserved.
CN-0017
Circuit Note
It is generally necessary to low-pass filter the DAC outputs to
remove image frequencies when driving a modulator. The
above interface lends itself well to the introduction of such a
filter. The filter can be inserted between the dc bias setting
resistors and the ac swing-limiting resistor. Doing so establishes
the input and output impedances for the filter.
COMMON VARIATIONS
The interface described here can be used to interface
any TxDAC converter with ground referenced 0 mA to 20 mA
output currents to any I/Q modulator with a 0.5 V input bias
level. For zero-IF applications, the AD9783 dual DAC provides
an LVDS interface, while the CMOS-driven AD9788 dual DAC
can generate a fine resolution complex IF input to the I/Q
modulator. The ADL5370/ADL5371/ADL5372/ADL5373/
ADL5374 family of I/Q modulators provides narrow-band
operation with high output 1 dB compression point and OIP3,
whereas the ADL5375 provides broadband high performance
operation from 400 MHz to 6 GHz. The ADL5385 I/Q modula-
tor uses a 2 × LO and operates from 50 MHz to 2.2 GHz.
A simulated filter example is shown in Figure 3 with a third-order
elliptical filter with a 3 dB frequency of 3 MHz. Matching input
and output impedances makes the filter design easier, so the
shunt resistor chosen is 100 Ω, producing an ac swing of 1 V p-p
differential for a 0 mA to 20 mA DAC full-scale output current.
In a practical application, the use of standard value components,
along with the input impedance of the I/Q modulator (2900 kΩ
in parallel with a few picofarads of input capacitance), will slightly
change the frequency response of this circuit.
LEARN MORE
AN-772 Application Note, A Design and Manufacturing Guide
for the Lead Frame Chip Scale Package (LFCSP). Analog
Devices.
LPI
AD9779A
ADL5371
2.7nH
93
92
19
20
OUT1_P
IBBP
RBIP
50Ω
RSLI
1.1nF
C1I
1.1nF
C2I
MT-016 Tutorial, Basic DAC Architectures III: Segmented DACs.
100Ω
RBIN
50Ω
Analog Devices.
OUT1_N
OUT2_N
OUT2_P
IBBN
QBBN
QBBP
LNI
2.7nH
MT-017 Tutorial, Oversampling Interpolating DACs. Analog
Devices.
LNQ
2.7nH
84
23
24
MT-031 Tutorial, Grounding Data Converters and Solving the
Mystery of 'AGND' and 'DGND'. Analog Devices.
RBQN
50Ω
1.1nF
C1Q
1.1nF
C2Q
RSLQ
100Ω
RBQP
83
MT-080 Tutorial, Mixers and Modulators. Analog Devices.
MT-101 Tutorial, Decoupling Techniques. Analog Devices.
50Ω
LPQ
2.7nH
Zumbahlen, Hank. 2006. Basic Linear Design. Analog Devices.
ISBN 0915550281. Chapters 4 and 11. Also available as
Linear Circuit Design Handbook. Elsevier-Newnes, 2008,
ISBN 0750687037, Chapters 4 and 11.
Figure 3. DAC Modulator Interface with 3 MHz Third-Order, Low-Pass Filter
(Calculated Component Values)
All the power supply pins of the ADL5371 must be connected to
the same 5 V source. Adjacent pins of the same name can be
tied together and decoupled to a large area ground plane with a
0.1 µF capacitor. These capacitors should be located as close as
possible to the device. The power supply can range between
4.75 V and 5.25 V.
Data Sheets
AD9779A Data Sheet.
ADL5371 Data Sheet.
The COM1 pin, COM2 pin, COM3 pin, and COM4 pin should
be tied to the same ground plane through low impedance paths.
The exposed paddle on the underside of the package should
also be soldered to a low thermal and electrical impedance
ground plane. If the ground plane spans multiple layers on the
circuit board, they should be stitched together with nine vias
under the exposed paddle. The AN-772 application note
discusses the thermal and electrical grounding of the
LFCSP_VQ in greater detail.
REVISION HISTORY
5/09—Rev. 0 to Rev. A
Updated Format..................................................................Universal
10/08—Revision 0: Initial Version
(Continued from first page) "Circuits from the Lab" are intended only for use with Analog Devices products and are the intellectual property of Analog Devices or its licensors. While you may
use the "Circuits from the Lab" in the design of your product, no other license is granted by implication or otherwise under any patents or other intellectual property by application or use of
the "Circuits from the Lab". Information furnished by Analog Devices is believed to be accurate and reliable. However, "Circuits from the Lab" are supplied "as is" and without warranties of any
kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability, noninfringement or fitness for a particular purpose and no responsibility is assumed
by Analog Devices for their use, nor for any infringements of patents or other rights of third parties that may result from their use. Analog Devices reserves the right to change any "Circuits
from the Lab" at any time without notice, but is under no obligation to do so. Trademarks and registered trademarks are the property of their respective owners.
©2008–2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
CN08210-0-5/09(A)
Rev. A | Page 2 of 2
相关型号:
CN-0019
Interfacing the ADL5373 I/Q Modulator to the AD9779A Dual-Channel, 1 GSPS High Speed DAC
ADI
CN-0020
Interfacing the ADL5374 I/Q Modulator to the AD9779A Dual-Channel, 1 GSPS High Speed DAC
ADI
CN-0021
Interfacing the ADL5375 I/Q Modulator to the AD9779A Dual-Channel, 1 GSPS High Speed DAC
ADI
CN-0046
Using the AD8352 as an Ultralow Distortion Differential RF/IF Front End for High Speed ADCs
ADI
CN-0072
Extending the Dynamic Range of the ADL5513 Logarithmic Detector Using the AD8368 Variable Gain Amplifier
ADI
CN-0144
Broadband Low Error Vector Magnitude Direct Conversion Transmitter Using LO Divide-by-2 Modulator
ADI
©2020 ICPDF网 联系我们和版权申明