CN-0072 [ADI]
Extending the Dynamic Range of the ADL5513 Logarithmic Detector Using the AD8368 Variable Gain Amplifier; 利用AD8368可变增益放大器扩展ADL5513对数检测器的动态范围
| 型号： | CN-0072 |
| 厂家： | 
ADI |
| 描述： | Extending the Dynamic Range of the ADL5513 Logarithmic Detector Using the AD8368 Variable Gain Amplifier |
| 文件： | 总3页 (文件大小：123K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Circuit Note
CN-0072
Devices Connected/Referenced
1 MHz to 4 GHz , 80 dB Logarithmic
Detector/Controller
800 MHz Linear-in-dB Variable Gain
Amplifier (VGA)
Circuit Designs Using Analog Devices Products
Apply these product pairings quickly and with confidence.
For more information and/or support call 1-800-AnalogD
(1-800-262-5643) or visit www.analog.com/circuit.
ADL5513
AD8368
Extending the Dynamic Range of the ADL5513 Logarithmic Detector
Using the AD8368 Variable Gain Amplifier
ADL5513 is attenuated and fed back to the gain control input of
the AD8368, providing precise control of the power at the input
of the ADL5513. Using this approach, the dynamic range of the
circuit is increased to 95 dB with excellent temperature stability
(see Figure 2). The output voltage is linear in dB with respect to
the input signal.
CIRCUIT FUNCTION AND BENEFITS
This circuit provides a solution for increasing the dynamic
range of the ADL5513 logarithmic detector. This is
accomplished by adding an AD8368 variable gain amplifier
(VGA) at the input of the ADL5513. The VOUT signal from the
VPOS
VPOS VPOS1 VPOS2 VPOS3
1nF
5.6pF
GND
VPOS
VPOS
VPOS2
215Ω
INPUT
10nF
0Ω
C7
1000pF
VPSI
VPSI
INPT
C12
1nF
C15
0.1µF
10nH
VPOS3
ICOM
10kΩ
MODE
VPSI
VPSO
VPSO
OUTP
AD8368
VPOS1
C12
1nF
C15
0Ω
10nF
0Ω
0.1µF
VOUT
VPSI
VPOS
VOUT
TADJ
0.1µF
12
1
2 INHI
OCOM
ENBL
47nF
1kΩ
C10
1nF
VSET 11
ADL5513
52.3Ω
3 INLO
4
COMM 10
BAND-PASS
120MHz
1nF
10nF
VPOS
9
1kΩ
VTADJ = 0.89V
100pF
Z1
0.1µF
VPOS
1kΩ
Figure 1.ADL5513 Logarithmic Detector and AD8368 VGA Providing 95 dB Dynamic Range at 120 MHz (Simplified Schematic)
Note: VPOS = +5 V
Rev. 0
“Circuits from the Lab” from Analog Devices have been designed and built by Analog Devices
engineers. Standard engineering practices have been employed in the design and construction of
each circuit, and their function and performance have been tested and verified in a lab environment
at room temperature. However, you are solely responsible for testing the circuit and determining its
suitability and applicability for your use and application. Accordingly, in no event shall Analog
Devices be liable for direct, indirect, special, incidental, consequential or punitive damages due to
anycause whatsoever connectedto the use ofany“Circuit fromthe Lab”. (Continued on last page)
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
©2009 Analog Devices, Inc. All rights reserved.
CN-0072
Circuit Note
CIRCUIT DESCRIPTION
1.750
1.625
1.500
1.375
1.250
1.125
1.000
0.875
0.750
0.625
0.500
0.375
0.250
3.0
The ADL5513 logarithmic detector dynamic range can be
extended by adding a separate VGA whose gain control input is
derived directly from VOUT. This extends the dynamic range by
the gain control range of the VGA. For the overall measurement
to remain linear in dB, the VGA must provide a linear-in-dB
(exponential) gain control function. The VGA gain must
decrease with an increase in its gain bias in the same way as the
ADL5513. Alternatively, an inverting op amp with suitable level
shifting can be used. It is convenient to select a VGA that needs
only a single 5.0 V supply and is capable of generating a single-
ended output. All of these conditions are met by the AD8368.
Figure 1 shows the simplified schematic. Using the inverse gain
mode (MODE pin low) of the AD8368, its gain decreases on a
slope of 37.5 mV/dB to a minimum value of −12 dB for a gain
voltage (VGAIN) of 1.0 V. The voltage, VGAIN, required by the
AD8368 is 50% of the output of the ADL5513. To scale this
voltage, it is necessary to insert a voltage divider at the output of
the ADL5513. Over the 1.5 V range from the output of the
ADL5513, the gain of the AD8368 varies by (0.5 × 1.5 V)÷
(37.5 mV/dB), or 20 dB. Combined with the 75 dB gain span (at
120 MHz) of the ADL5513, this results in a 1.5 V change in
2.5
2.0
1.5
1.0
0.5
0
–0.5
–1.0
–1.5
–2.0
–2.5
–3.0
V
V
V
+25°C
–40°C
+85°C
OUT
OUT
OUT
ERROR +25°C
ERROR –40°C
ERROR +85°C
–90 –80 –70 –60 –50 –40 –30 –20 –10
0
10
20
P
(dBm)
IN
Figure 2. Output and Conformance for the AD8368/ADL5513 Extended
Dynamic Range Circuit at 120 MHz
COMMON VARIATIONS
The application circuit described here can be modified for any
IF frequency within the operating range of the AD8368 and
ADL5513 by selecting the appropriate band-pass filter. For
operation above 800 MHz, the ADL5330 can be used in place of
the AD8368. The ADL5330 VGA can be used at frequencies
between 10 MHz and 3 GHz. Using the ADL5330 also requires
an inverter between the ADL5330 gain pin and the gain control
voltage from the ADL5513. A single-supply operational
amplifier such as the AD8061 can be configured for use as an
inverter in this application.
V
OUT for a 95 dB change at the input to the AD8368.
Due to the amplification of out-of-band noise by the AD8368, a
band-pass filter is used between the AD8368 and ADL5513 to
increase the low-signal sensitivity. The VGA amplifies low
power signals and attenuates high power signals to fit them in
the detectable range of the ADL5513. If an amplifier with higher
gain and lower noise figure is used, better than 90 dB sensitivity
can be achieved for use in a receive-signal-strength-indicator
(RSSI) application.
LEARN MORE
Figure 2 shows the data results of the extended dynamic range
at 120 MHz and the corresponding error in VOUT
MT-073 Tutorial, High Speed Variable Gain Amplifiers (VGAs).
.
Analog Devices.
Due to the high frequencies and wide dynamic ranges involved,
the circuit must be constructed on a multilayer PC board that
has at least one layer for the ground plane. Each IC power pin
must be decoupled with a 0.1 µF low inductance ceramic
capacitor as shown in Figure 1. Some power pins have an
additional smaller value decoupling capacitor (low ESL) for
extremely high frequencies. The “0 Ω” resistors on the
schematic represent optional small resistor values (less than
10 Ω) or ferrite beads that may be added for more decoupling.
The data sheets for the ADL5513 and the AD8368 show the
optimal layouts of the respective evaluation boards.
MT-077 Tutorial, Log Amp Basics. Analog Devices.
MT-078 Tutorial, High Frequency Log Amps. Analog Devices.
MT-101 Tutorial, Decoupling Techniques. Analog Devices.
Data Sheets
AD8061 Data Sheet.
AD8368 Data Sheet.
ADL5330 Data Sheet.
ADL5513 Data Sheet.
On the underside of both the ADL5513 and the AD8368 chip
scale package there is an exposed paddle. This paddle is
internally connected to the ground of the chip. Solder the
paddle to the low impedance ground plane on the PCB to
ensure specified electrical performance and to provide thermal
relief. It is also recommended that the ground planes on all
layers under the paddle be stitched together with vias to reduce
thermal impedance.
REVISION HISTORY
7/09—Revision 0: Initial Version
Rev. 0 | Page 2 of 3
Circuit Note
CN-0072
(Continued from first page) "Circuits from the Lab" are intended only for use with Analog Devices products and are the intellectual property of Analog Devices or its licensors. While you may
use the "Circuits from the Lab" in the design of your product, no other license is granted by implication or otherwise under any patents or other intellectual property by application or use of
the "Circuits from the Lab". Information furnished by Analog Devices is believed to be accurate and reliable. However, "Circuits from the Lab" are supplied "as is" and without warranties of any
kind, express, implied, or statutory including, but not limited to, any implied warranty of merchantability, noninfringement or fitness for a particular purpose and no responsibility is assumed
by Analog Devices for their use, nor for any infringements of patents or other rights of third parties that may result from their use. Analog Devices reserves the right to change any "Circuits
from the Lab" at any time without notice, but is under no obligation to do so. Trademarks and registered trademarks are the property of their respective owners.
©2009 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
CN08175-0-7/09(0)
Rev. 0 | Page 3 of 3
相关型号：
CN-0144
Broadband Low Error Vector Magnitude Direct Conversion Transmitter Using LO Divide-by-2 Modulator
ADI
CN-0147
Powering a Fractional-N Voltage Controlled Oscillator with Low Noise LDO Regulators for Reduced Phase Noise
ADI
CN-0150
Software-Calibrated, 1 MHz to 8 GHz, 60 dB RF Power Measurement System Using a Logarithmic Detector
ADI
CN-0171
Low Noise, Low Distortion Single-Ended Input Drive Circuit for Differential Input IF Sampling ADCs
ADI
CN-0174
Low Noise, 12 GHz, Microwave Fractional-N Phase-Locked Loop Using an Active Loop Filter and RF Prescaler
ADI
©2020 ICPDF网 联系我们和版权申明