EVAL-ADCMP601BKSZ [ADI]
Rail-to-Rail, Very Fast, 2.5 V to 5.5 V; 轨到轨，速度非常快， 2.5 V至5.5 V
| 型号： | EVAL-ADCMP601BKSZ |
| 厂家： | 
ADI |
| 描述： | Rail-to-Rail, Very Fast, 2.5 V to 5.5 V |
| 文件： | 总16页 (文件大小：291K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
Rail-to-Rail, Very Fast, 2.5 V to 5.5 V,
Single-Supply TTL/CMOS Comparators
ADCMP600/ADCMP601/ADCMP602
FEATURES
FUNCTIONAL BLOCK DIAGRAM
Fully specified rail to rail at VCC = 2.5 V to 5.5 V
Input common-mode voltage from −0.2 V to VCC + 0.2 V
Low glitch CMOS-/TTL-compatible output stage
3.5 ns propagation delay
NONINVERTING
INPUT
ADCMP600/
Q OUTPUT
ADCMP601/
ADCMP602
INVERTING
10 mW at 3.3 V
INPUT
Shutdown pin
Single-pin control for programmable hysteresis and latch
Power supply rejection > 50 dB
Improved replacement for MAX999
−40°C to +125°C operation
LE/HYS
(EXCEPT ADCMP600)
S
DN
(ADCMP602 ONLY)
Figure 1.
APPLICATIONS
High speed instrumentation
Clock and data signal restoration
Logic level shifting or translation
Pulse spectroscopy
High speed line receivers
Threshold detection
Peak and zero-crossing detectors
High speed trigger circuitry
Pulse-width modulators
Current/voltage-controlled oscillators
Automatic test equipment (ATE)
GENERAL DESCRIPTION
input signal range while still allowing independent output
swing control and power savings.
The ADCMP600, ADCMP601, and ADCMP602 are very fast
comparators fabricated on XFCB2, an Analog Devices, Inc.
proprietary process. These comparators are exceptionally
versatile and easy to use. Features include an input range from
GND − 0.5 V to VCC + 0.2 V, low noise, TTL-/CMOS-compatible
output drivers, and latch inputs with adjustable hysteresis
and/or shutdown inputs.
The TTL-/CMOS-compatible output stage is designed to drive
up to 5 pF with full timing specs and to degrade in a graceful
and linear fashion as additional capacitance is added. The
comparator input stage offers robust protection against large
input overdrive, and the outputs do not phase reverse when the
valid input signal range is exceeded. Latch and programmable
hysteresis features are also provided with a unique single-pin
control option.
The device offers 5 ns propagation delay with 10 mV overdrive
on 3 mA typical supply current.
A flexible power supply scheme allows the devices to operate
with a single +2.5 V positive supply and a −0.5 V to +2.8 V
input signal range up to a +5.5 V positive supply with a −0.5 V
to +5.8 V input signal range. Split input/output supplies with no
sequencing restrictions on the ADCMP602 support a wide
The ADCMP600 is available in 5-lead SC70 and SOT-23
packages, the ADCMP601 is available in a 6-lead SC70 package,
and the ADCMP602 is available in an 8-lead MSOP package.
Rev. A
Information furnished by Analog Devices is believed to be accurate and reliable. However, no
responsibility is assumed by Analog Devices for its use, nor for any infringements of patents or other
rightsof third parties that may result fromits use. Specifications subject to change without notice. No
license is granted by implication or otherwise under any patent or patent rights of Analog Devices.
Trademarks andregisteredtrademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
www.analog.com
Fax: 781.461.3113 ©2006–2011 Analog Devices, Inc. All rights reserved.
ADCMP600/ADCMP601/ADCMP602
TABLE OF CONTENTS
Features .............................................................................................. 1
Application Information................................................................ 10
Power/Ground Layout and Bypassing..................................... 10
TTL-/CMOS-Compatible Output Stage ................................. 10
Using/Disabling the Latch Feature........................................... 10
Optimizing Performance........................................................... 11
Comparator Propagation Delay Dispersion ........................... 11
Comparator Hysteresis .............................................................. 11
Crossover Bias Point .................................................................. 12
Minimum Input Slew Rate Requirement................................ 12
Typical Application Circuits ......................................................... 13
Outline Dimensions....................................................................... 14
Ordering Guide .......................................................................... 16
Applications....................................................................................... 1
Functional Block Diagram .............................................................. 1
General Description ......................................................................... 1
Revision History ............................................................................... 2
Specifications..................................................................................... 3
Electrical Characteristics............................................................. 3
Timing Information ......................................................................... 5
Absolute Maximum Ratings............................................................ 6
Thermal Resistance ...................................................................... 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
REVISION HISTORY
1/11—Rev. 0 to Rev. A
Changed VEE Pin to GND............................................. Throughout
Changes to Common-Mode Dispersion Conditions................... 4
Changes to Figure 15 and Figure 16............................................... 9
Changes to Comparator Hysteresis Section................................ 12
Updated Outline Dimensions....................................................... 14
Changes to Ordering Guide .......................................................... 15
10/06—Revision 0: Initial Version
Rev. A | Page 2 of 16
ADCMP600/ADCMP601/ADCMP602
SPECIFICATIONS
ELECTRICAL CHARACTERISTICS
VCCI = VCCO = 2.5 V, TA = 25°C, unless otherwise noted.
Table 1.
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
DC INPUT CHARACTERISTICS
Voltage Range
Common-Mode Range
Differential Voltage
Offset Voltage
Bias Current
Offset Current
Capacitance
VP, VN
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
VCC = 2.5 V to 5.5 V
−0.5
−0.2
VCC + 0.2
VCC + 0.2
VCC + 0.8
+5.0
+5.0
+2.0
V
V
V
VOS
IP, IN
−5.0
−5.0
−2.0
2
2
mV
µA
µA
pF
kΩ
kΩ
dB
dB
CP, CN
1
Resistance, Differential Mode
Resistance, Common Mode
Active Gain
−0.1 V to VCC
−0.5 V to VCC + 0.5 V
200
100
700
350
85
AV
CMRR
Common-Mode Rejection Ratio
VCCI = 2.5 V, VCCO = 2.5 V,
50
50
V
CM = −0.2 V to +2.7 V
VCCI = 2.5 V, VCCO = 5.5 V
dB
Hysteresis (ADCMP600)
Hysteresis (ADCMP601/ADCMP602)
2
0.1
mV
mV
RHYS = ∞
LATCH ENABLE PIN CHARACTERISTICS
(ADCMP601/ADCMP602 Only)
VIH
VIL
IIH
Hysteresis is shut off
Latch mode guaranteed
VIH = VCC
2.0
−0.2
−6
VCC
+0.8
+6
V
V
µA
mA
+0.4
IOL
VIL = 0.4 V
−0.1
+0.1
HYSTERESIS MODE AND TIMING
(ADCMP601/ADCMP602 Only)
Hysteresis Mode Bias Voltage
Resistor Value
Hysteresis Current
Latch Setup Time
Latch Hold Time
Latch-to-Output Delay
Latch Minimum Pulse Width
Current −1 μA
Hysteresis = 120 mV
Hysteresis = 120 mV
VOD = 50 mV
VOD = 50 mV
VOD = 50 mV
1.145
65
−18
1.25
80
−12
−2
2.6
27
21
1.35
120
−7
V
kΩ
µA
ns
ns
ns
ns
tS
tH
tPLOH, tPLOL
tPL
VOD = 50 mV
SHUTDOWN PIN CHARACTERISTICS
(ADCMP602 Only)
VIH
VIL
IIH
IOL
Comparator is operating
Shutdown guaranteed
VIH = VCC
VIL = 0 V
ICCO < 500 µA
VOD = 100 mV, output valid
VCCO = 2.5 V to 5.5 V
IOH = 8 mA, VCCO = 2.5 V
IOL = 8 mA, VCCO = 2.5 V
IOH = 6 mA, VCCO = 2.5 V
IOL = 6 mA, VCCO = 2.5 V
2.0
−0.2
−6
VCCO
+0.6
6
V
V
µA
µA
ns
ns
+0.4
−100
20
50
Sleep Time
Wake-Up Time
tSD
tH
DC OUTPUT CHARACTERISTICS
Output Voltage High Level
Output Voltage Low Level
Output Voltage High Level at −40°C
Output Voltage Low Level at− 40°C
VOH
VOL
VOH
VOL
VCC − 0.4
VCC − 0.4
V
V
V
V
0.4
0.4
Rev. A | Page 3 of 16
ADCMP600/ADCMP601/ADCMP602
Parameter
Symbol
Conditions
Min
Typ
Max
Unit
AC PERFORMANCE1
Rise Time /Fall Time
tR tF
10% to 90%, VCCO = 2.5 V
10% to 90%, VCCO = 5.5 V
VOD = 50 mV, VCCO = 2.5 V
VOD = 50 mV, VCCO = 5.5 V
VOD = 10 mV, VCCO = 2.5 V
VCCO = 2.5 V to 5.5 V
2.2
4
3.5
4.3
5
ns
ns
ns
ns
ns
ps
Propagation Delay
tPD
Propagation Delay Skew—Rising to
Falling Transition
500
V
OD = 50 mV
Overdrive Dispersion
Common-Mode Dispersion
10 mV < VOD < 125 mV
−0.2 V < VCM < VCCI + 0.2 V
1.2
200
ns
ps
V
OD = 50 mV
Minimum Pulse Width
PWMIN
VCCI = VCCO = 2.5 V
PWOUT = 90% of PWIN
VCCI = VCCO = 5.5 V
3
ns
ns
4.5
PWOUT = 90% of PWIN
POWER SUPPLY
Input Supply Voltage Range
Output Supply Voltage Range
Positive Supply Differential
(ADCMP602 Only)
VCCI
VCCO
VCCI − VCCO
2.5
2.5
−3.0
5.5
5.5
+3.0
V
V
V
Operating
VCCI − VCCO
IVCC
Nonoperating
VCC = 2.5 V
VCC = 5.5 V
VCCI = 2.5 V
VCCI = 5.5 V
VCCO = 2.5 V
VCCO = 5.5 V
VCC = 2.5 V
−5.5
+5.5
3.5
4.0
1.4
2.0
3.0
3.5
9
V
mA
Positive Supply Current
(ADCMP600/ADCMP601)
Input Section Supply Current
(ADCMP602 Only)
Output Section Supply Current
(ADCMP602 Only)
3
3.5
0.9
1.2
1.45
2.1
7
IVCCI
mA
mA
mA
mA
mW
mW
dB
IVCCO
Power Dissipation
PD
PD
PSRR
VCC = 5.5 V
VCCI = 2.5 V to 5 V
VCC = 2.5 V
20
23
Power Supply Rejection Ratio
Shutdown Mode ICCI
(ADCMP602 Only)
Shutdown Mode ICCO
(ADCMP602 Only)
−50
240
400
30
µA
VCC =2.5 V
µA
1 VIN = 100 mV square input at 50 MHz, VCM = 0 V, CL = 5 pF, VCCI = VCCO =2.5 V, unless otherwise noted.
Rev. A | Page 4 of 16
ADCMP600/ADCMP601/ADCMP602
TIMING INFORMATION
Figure 2 illustrates the ADCMP600/ADCMP601/ADCMP602 latch timing relationships. Table 2 provides definitions of the terms shown
in Figure 2.
1.1V
LATCH ENABLE
tS
tPL
tH
V
IN
DIFFERENTIAL
INPUT VOLTAGE
V
± V
OS
N
V
OD
tPDL
tPLOH
Q OUTPUT
50%
tF
Figure 2. System Timing Diagram
Table 2. Timing Descriptions
Symbol Timing
Description
tPDH
tPDL
tPLOH
tPLOL
tH
Input to output high delay
Propagation delay measured from the time the input signal crosses the reference ( the
input offset voltage) to the 50% point of an output low-to-high transition.
Propagation delay measured from the time the input signal crosses the reference ( the
input offset voltage) to the 50% point of an output high-to-low transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output low-to-high transition.
Propagation delay measured from the 50% point of the latch enable signal low-to-high
transition to the 50% point of an output high-to-low transition.
Input to output low delay
Latch enable to output high delay
Latch enable to output low delay
Minimum hold time
Minimum time after the negative transition of the latch enable signal that the input signal
must remain unchanged to be acquired and held at the outputs.
tPL
tS
Minimum latch enable pulse width
Minimum setup time
Minimum time that the latch enable signal must be high to acquire an input signal change.
Minimum time before the negative transition of the latch enable signal occurs that an
input signal change must be present to be acquired and held at the outputs.
tR
Output rise time
Output fall time
Voltage overdrive
Amount of time required to transition from a low to a high output as measured at the 20%
and 80% points.
Amount of time required to transition from a high to a low output as measured at the 20%
and 80% points.
tF
VOD
Difference between the input voltages VA and VB.
Rev. A | Page 5 of 16
ADCMP600/ADCMP601/ADCMP602
ABSOLUTE MAXIMUM RATINGS
Stresses above those listed under Absolute Maximum Ratings
may cause permanent damage to the device. This is a stress
rating only; functional operation of the device at these or any
other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Table 3.
Parameter
Rating
Supply Voltages
Input Supply Voltage (VCCI to GND)
Output Supply Voltage
(VCCO to GND)
−0.5 V to +6.0 V
−0.5 V to +6.0 V
Positive Supply Differential
−6.0 V to +6.0 V
(VCCI − VCCO
Input Voltages
Input Voltage
)
THERMAL RESISTANCE
θJA is specified for the worst-case conditions, that is, a device
soldered in a circuit board for surface-mount packages.
−0.5 V to VCCI + 0.5 V
(VCCI + 0.5 V)
50 mA
Differential Input Voltage
Maximum Input/Output Current
Shutdown Control Pin
Applied Voltage (HYS to GND)
Maximum Input/Output Current
Latch/Hysteresis Control Pin
Applied Voltage (HYS to GND)
Maximum Input/Output Current
Output Current
Table 4. Thermal Resistance
Package Type
ADCMP600 SC70 5-Lead
ADCMP600 SOT-23 5-Lead
ADCMP601 SC70 6-Lead
1
θJA
Unit
°C/W
°C/W
°C/W
°C/W
−0.5 V to VCCO + 0.5 V
50 mA
426
302
426
130
ADCMP602 MSOP 5-Lead
−0.5 V to VCCO + 0.5 V
50 mA
50 mA
1 Measurement in still air.
ESD CAUTION
Temperature
Operating Temperature, Ambient
Operating Temperature, Junction
Storage Temperature Range
−40°C to +125°C
150°C
−65°C to +150°C
Rev. A | Page 6 of 16
ADCMP600/ADCMP601/ADCMP602
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
Q
1
2
3
6
5
4
V
/V
CCI CCO
Q
1
2
3
5
V
/V
CCI CCO
V
1
2
3
4
8
7
6
5
V
CCO
CCI
ADCMP600
ADCMP601
ADCMP602
GND
GND
LE/HYS
V
P
Q
TOP VIEW
TOP VIEW
TOP VIEW
(Not to Scale)
(Not to Scale)
V
GND
LE/HYS
N
(Not to Scale)
V
P
4
V
N
V
P
V
N
S
DN
Figure 3. ADCMP600 Pin Configuration
Figure 4. ADCMP601 Pin Configuration
Figure 5. ADCMP602 Pin Configuration
Table 5. ADCMP600 (SOT-23-5 and SC70-5) Pin Function Descriptions
Pin No.
Mnemonic
Description
1
Q
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater
than the analog voltage at the inverting input, VN.
2
3
4
5
GND
VP
VN
Negative Supply Voltage.
Noninverting Analog Input.
Inverting Analog Input.
Input Section Supply/Output Section Supply. Shared pin.
VCCI/VCCO
Table 6. ADCMP601 (SC70-6) Pin Function Descriptions
Pin No.
Mnemonic
Description
1
Q
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater
than the analog voltage at the inverting input, VN, if the comparator is in compare mode.
2
3
4
5
6
GND
VP
VN
LE/HYS
VCCI/VCCO
Negative Supply Voltage.
Noninverting Analog Input.
Inverting Analog Input.
Latch/Hysteresis Control. Bias with resistor or current for hysteresis adjustment; drive low to latch.
Input Section Supply/Output Section Supply. Shared pin.
Table 7. ADCMP602 (MSOP-8) Pin Function Descriptions
Pin No.
Mnemonic
Description
1
2
3
4
5
6
7
VCCI
VP
VN
Input Section Supply.
Noninverting Analog Input.
Inverting Analog Input.
Shutdown. Drive this pin low to shut down the device.
Latch/Hysteresis Control. Bias with resistor or current for hysteresis adjustment; drive low to latch.
Negative Supply Voltage.
Noninverting Output. Q is at logic high if the analog voltage at the noninverting input, VP, is greater
than the analog voltage at the inverting input, VN, if the comparator is in compare mode.
SDN
LE/HYS
GND
Q
8
VCCO
Output Section Supply.
Rev. A | Page 7 of 16
ADCMP600/ADCMP601/ADCMP602
TYPICAL PERFORMANCE CHARACTERISTICS
VCCI = VCCO = 2.5 V, TA = 25°C, unless otherwise noted.
20
15
800
600
I
VS V
I
OL
OL
VS V
OH
V
= 5.5V
V
= 2.5V
OH
CC
CC
10
400
200
5
0
0
–5
–200
–400
–600
–800
–10
–15
–20
–1.0 –0.6 –0.2 0.2 0.6 1.0 1.4 1.8 2.2 2.6 3.0 3.4
(V)
–1
0
1
2
3
4
5
6
7
LE/HYS (V)
V
OUT
Figure 6. LE/HYS Pin I/V Characteristics
Figure 9. VOH/VOL vs. Current Load
150
100
50
250
200
150
100
50
V
= 2.5V
V
= 5.5V
CC
CC
V
= 5.5V
CC
0
–50
–100
–150
V
= 2.5V
CC
0
–1
0
1
2
3
4
5
6
7
50
150
250
350
450
550
650
SHUTDOWN PIN VOLTAGE (V)
HYSTERESIS RESISTOR (kΩ)
Figure 7. SDN Pin I/V Characteristics
Figure 10. Hysteresis vs. RHYS Control Resistor
450
400
350
300
250
200
150
100
50
20
V
= 2.5V
CC
15
10
LOT 1
5
0
LOT 2
–5
I
@ +125°C
B
–10
–15
–20
I
@ +25°C
B
I
@ –40°C
B
0
0
–5
–10
–15
–20
–1.0 –0.5
0
0.5
1.0
1.5
2.0
2.5
3.0
3.5
PIN CURRENT (µA)
COMMON-MODE VOLTAGE (V)
Figure 11. Hysteresis vs. Pin Current
Figure 8. Input Bias Current vs. Input Common Mode
Rev. A | Page 8 of 16
ADCMP600/ADCMP601/ADCMP602
4.8
4.6
4.4
4.2
4.0
3.8
3.6
3.4
3.2
3.0
1.00V/DIV
M4.00ns
0
10 20 30 40 50 60 70 80 90 100 110 120 130 140
OVERDRIVE (mV)
Figure 12. Propagation Delay vs. Input Overdrive at VCC = 2.5 V
Figure 15. 50 MHz Output Waveform VCC = 5.5 V
4.0
V
AT V = 2.5V
CC
CM
3.8
3.6
3.4
3.2
3.0
RISE
FALL
–0.6
0
0.6
1.2
1.8
2.4
3.0
COMMON-MODE VOLTAGE (V)
500mV/DIV
M4.00ns
Figure16. 50 MHz Output Waveforms @ 2.5 V
Figure 13. Propagation Delay vs. Input Common-Mode Voltage
at VCC = 2.5 V
5.0
4.8
4.6
4.4
4.2
4.0
RISE
3.8
3.6
FALL
3.4
3.2
3.0
2.5
3.0
3.5
4.0
V
4.5
(V)
5.0
5.5
6.0
CCO
Figure 14. Propagation Delay vs. VCCO
Rev. A | Page 9 of 16
ADCMP600/ADCMP601/ADCMP602
APPLICATION INFORMATION
This delay is measured to the 50% point for the supply in use;
therefore, the fastest times are observed with the VCC supply at
2.5 V, and larger values are observed when driving loads that
switch at other levels.
POWER/GROUND LAYOUT AND BYPASSING
The ADCMP600/ADCMP601/ADCMP602 comparators are very
high speed devices. Despite the low noise output stage, it is essential
to use proper high speed design techniques to achieve the specified
performance. Because comparators are uncompensated amplifiers,
feedback in any phase relationship is likely to cause oscillations or
undesired hysteresis. Of critical importance is the use of low
impedance supply planes, particularly the output supply plane
(VCCO) and the ground plane (GND). Individual supply planes are
recommended as part of a multilayer board. Providing the lowest
inductance return path for switching currents ensures the best
possible performance in the target application.
When duty cycle accuracy is critical, the logic being driven
should switch at 50% of VCC and load capacitance should be
minimized. When in doubt, it is best to power VCCO or the
entire device from the logic supply and rely on the input PSRR
and CMRR to reject noise.
Overdrive and input slew rate dispersions are not significantly
affected by output loading and VCC variations.
The TTL-/CMOS-compatible output stage is shown in the
simplified schematic diagram (Figure 17). Because of its
inherent symmetry and generally good behavior, this output
stage is readily adaptable for driving various filters and other
unusual loads.
It is also important to adequately bypass the input and output
supplies. Multiple high quality 0.01 µF bypass capacitors should
be placed as close as possible to each of the VCCI and VCCO supply
pins and should be connected to the GND plane with redundant
vias. At least one of these should be placed to provide a physically
short return path for output currents flowing back from ground
to the VCC pin. High frequency bypass capacitors should be
carefully selected for minimum inductance and ESR. Parasitic
layout inductance should also be strictly controlled to maximize
the effectiveness of the bypass at high frequencies.
V
LOGIC
A1
Q1
+IN
–IN
OUTPUT
If the package allows and the input and output supplies have
been connected separately such that VCCI ≠ VCCO, care should be
taken to bypass each of these supplies separately to the GND
plane. A bypass capacitor should never be connected between
them. It is recommended that the GND plane separate the VCCI
and VCCO planes when the circuit board layout is designed to
minimize coupling between the two supplies and to take
advantage of the additional bypass capacitance from each
respective supply to the ground plane. This enhances the
performance when split input/output supplies are used. If the
input and output supplies are connected together for single-supply
operation such that VCCI = VCCO, coupling between the two supplies
is unavoidable; however, careful board placement can help keep
output return currents away from the inputs.
A
V
A2
Q2
GAIN STAGE
OUTPUT STAGE
Figure 17. Simplified Schematic Diagram of
TTL-/CMOS-Compatible Output Stage
USING/DISABLING THE LATCH FEATURE
The latch input is designed for maximum versatility. It can
safely be left floating for fixed hysteresis or be tied to VCC to
remove the hysteresis, or it can be driven low by any standard
TTL/CMOS device as a high speed latch.
TTL-/CMOS-COMPATIBLE OUTPUT STAGE
In addition, the pin can be operated as a hysteresis control pin
with a bias voltage of 1.25 V nominal and an input resistance of
approximately 7000 Ω. This allows the comparator hysteresis to
be easily and accurately controlled by either a resistor or an
inexpensive CMOS DAC.
Specified propagation delay performance can be achieved only
by keeping the capacitive load at or below the specified minimums.
The outputs of the devices are designed to directly drive one
Schottky TTL or three low power Schottky TTL loads or the
equivalent. For large fan outputs, buses, or transmission lines,
use an appropriate buffer to maintain the excellent speed and
stability of the comparator.
Hysteresis control and latch mode can be used together if an
open drain, an open collector, or a three-state driver is connected
parallel to the hysteresis control resistor or current source.
With the rated 5 pF load capacitance applied, more than half of
the total device propagation delay is output stage slew time,
even at 2.5 V VCC. Because of this, the total prop delay decreases
as VCCO decreases, and instability in the power supply may
appear as excess delay dispersion.
Due to the programmable hysteresis feature, the logic threshold
of the latch pin is approximately 1.1 V regardless of VCC
.
Rev. A | Page 10 of 16
ADCMP600/ADCMP601/ADCMP602
INPUT VOLTAGE
1V/ns
OPTIMIZING PERFORMANCE
As with any high speed comparator, proper design and layout
techniques are essential for obtaining the specified performance.
Stray capacitance, inductance, inductive power and ground
impedances, or other layout issues can severely limit performance
and often cause oscillation. Large discontinuities along input
and output transmission lines can also limit the specified pulse-
width dispersion performance. The source impedance should
be minimized as much as is practicable. High source impedance,
in combination with the parasitic input capacitance of the
comparator, causes an undesirable degradation in bandwidth at
the input, thus degrading the overall response. Thermal noise
from large resistances can easily cause extra jitter with slowly
slewing input signals; higher impedances encourage undesired
coupling.
V
± V
OS
N
10V/ns
DISPERSION
Q/Q OUTPUT
Figure 19. Propagation Delay—Slew Rate Dispersion
COMPARATOR HYSTERESIS
The addition of hysteresis to a comparator is often desirable in a
noisy environment, or when the differential input amplitudes
are relatively small or slow moving. Figure 20 shows the transfer
function for a comparator with hysteresis. As the input voltage
approaches the threshold (0.0 V, in this example) from below
the threshold region in a positive direction, the comparator
switches from low to high when the input crosses +VH/2, and the
new switching threshold becomes −VH/2. The comparator remains
in the high state until the new threshold, −VH/2, is crossed from
below the threshold region in a negative direction. In this manner,
noise or feedback output signals centered on 0.0 V input cannot
cause the comparator to switch states unless it exceeds the region
bounded by VH/2.
COMPARATOR PROPAGATION DELAY
DISPERSION
The ADCMP600/ADCMP601/ADCMP602 comparators are
designed to reduce propagation delay dispersion over a wide
input overdrive range. Propagation delay dispersion is the
variation in propagation delay that results from a change in the
degree of overdrive or slew rate (that is, how far or how fast the
input signal exceeds the switching threshold).
Propagation delay dispersion is a specification that becomes
important in high speed, time-critical applications, such as data
communication, automatic test and measurement, and instru-
mentation. It is also important in event-driven applications, such
as pulse spectroscopy, nuclear instrumentation, and medical
imaging. Dispersion is defined as the variation in propagation
delay as the input overdrive conditions are changed (Figure 18
and Figure 19).
OUTPUT
V
OH
V
OL
The device dispersion is typically < 2 ns as the overdrive varies
from 10 mV to 125 mV. This specification applies to both
positive and negative signals because the device has very closely
matched delays both positive-going and negative-going inputs.
500mV OVERDRIVE
INPUT
0
–V
2
+V
2
H
H
Figure 20. Comparator Hysteresis Transfer Function
The customary technique for introducing hysteresis into a
comparator uses positive feedback from the output back to the
input. One limitation of this approach is that the amount of
hysteresis varies with the output logic levels, resulting in
hysteresis that is not symmetric about the threshold. The
external feedback network can also introduce significant
parasitics that reduce high speed performance and induce
oscillation in some cases.
INPUT VOLTAGE
10mV OVERDRIVE
V
± V
OS
N
DISPERSION
Q/Q OUTPUT
Figure 18. Propagation Delay—Overdrive Dispersion
These ADCMP600 features a fixed hysteresis of approximately
2 mV. The ADCMP601 and ADCMP602 comparators offer a
programmable Hysteresis feature that can significantly improve
accuracy and stability. Connecting an external pull-down
resistor or a current source from the LE/HYS pin to GND,
varies the amount of hysteresis in a predictable, stable manner.
Rev. A | Page 11 of 16
ADCMP600/ADCMP601/ADCMP602
250
200
150
100
50
Leaving the LE/HYS pin disconnected results in a fixed
hysteresis of 2 mV; driving this pin high removes hysteresis. The
maximum hysteresis that can be applied using this pin is
approximately 160 m V. Figure 21 illustrates the amount of
hysteresis applied as a function of the external resistor value,
and Figure 11 illustrates hysteresis as a function of the current.
V
= 5.5V
CC
The hysteresis control pin appears as a 1.25 V bias voltage seen
through a series resistance of 7 kΩ. The bias voltage changes
20% throughout the hysteresis control range. The advantages
of applying hysteresis in this manner are improved accuracy,
improved stability, reduced component count, and maximum
versatility. An external bypass capacitor is not recommended on
the HYS pin because it impairs the latch function and often
degrades the jitter performance of the device. As described in the
Using/Disabling the Latch Feature section, hysteresis control
need not compromise the latch function.
V
= 2.5V
CC
0
50
150
250
350
450
550
650
HYSTERESIS RESISTOR (kΩ)
Figure 21. Hysteresis vs. RHYS Control Resistor
MINIMUM INPUT SLEW RATE REQUIREMENT
With the rated load capacitance and normal good PC Board
design practice, as discussed in the Optimizing Performance
section, these comparators should be stable at any input slew
rate with no hysteresis. Broadband noise from the input stage is
observed in place of the violent chattering seen with most other
high speed comparators. With additional capacitive loading or
poor bypassing, oscillation is observed. This oscillation is due to
the high gain bandwidth of the comparator in combination with
feedback parasitics in the package and PC board. In many
applications, chattering is not harmful.
CROSSOVER BIAS POINT
In both op amps and comparators, rail-to-rail inputs of this type
have a dual front-end design. Certain devices are active near the
VCC rail and others are active near the GND rail. At some predeter-
mined point in the common-mode range, a crossover occurs. At
this point, normally VCC/2, the direction of the bias current reverses
and the measured offset voltages and currents change.
The ADCMP600/ADCMP601/ADCMP602 comparators
slightly elaborate on this scheme. Crossover points can be found
at approximately 0.8 V and 1.6 V.
Rev. A | Page 12 of 16
ADCMP600/ADCMP601/ADCMP602
TYPICAL APPLICATION CIRCUITS
5V
0.1µF
2.5V
2kΩ
OUTPUT
2kΩ
ADCMP600
0.1µF
CMOS
PWM
ADCMP600
Figure 22. Self-Biased, 50% Slicer
OUTPUT
INPUT
1.25V
±50mV
INPUT
1.25V
REF
10kΩ
CMOS
10kΩ
10kΩ
V
DD
2.5V TO 5V
ADCMP601
LE/HYS
40kΩ
CMOS
100Ω
ADCMP600
82pF
Figure 23. LVDS-to-CMOS Receiver
Figure 25. Oscillator and Pulse-Width Modulator
2.5V TO 5V
2.5V
10kΩ
ADCMP601
20kΩ
20kΩ
OUTPUT
1.5MHz TO 30MHz
ADCMP601
LE/HYS
DIGITAL
INPUT
74 AHC
1G07
LE/HYS
82pF
CONTROL
VOLTAGE
0V TO 2.5V
HYSTERESIS
CURRENT
100kΩ
100kΩ
10kΩ
Figure 24. Voltage-Controlled Oscillator
Figure 26. Hysteresis Adjustment with Latch
Rev. A | Page 13 of 16
ADCMP600/ADCMP601/ADCMP602
OUTLINE DIMENSIONS
2.20
2.00
1.80
2.40
2.10
1.80
5
1
4
3
1.35
1.25
1.15
2
0.65 BSC
1.10
1.00
0.90
0.70
0.40
0.10
0.80
0.46
0.36
0.26
0.22
0.08
SEATING
PLANE
0.10 MAX
0.30
0.15
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-203-AA
Figure 27. 5-Lead Thin Shrink Small Outline Transistor Package (SC70)
(KS-5)
Dimensions shown in millimeters
3.00
2.90
2.80
5
1
4
3
3.00
2.80
2.60
1.70
1.60
1.50
2
0.95 BSC
1.90
BSC
1.30
1.15
0.90
0.20 MAX
0.08 MIN
1.45 MAX
0.95 MIN
0.55
0.45
0.35
0.15 MAX
0.05 MIN
10°
5°
0°
SEATING
PLANE
0.60
BSC
0.50 MAX
0.35 MIN
COMPLIANT TO JEDEC STANDARDS MO-178-AA
Figure 28. 5-Lead Small Outline Transistor Package (SOT-23)
(RJ-5)
Dimensions shown in millimeters
Rev. A | Page 14 of 16
ADCMP600/ADCMP601/ADCMP602
2.20
2.00
1.80
2.40
2.10
1.80
6
1
5
2
4
3
1.35
1.25
1.15
0.65 BSC
1.30 BSC
1.00
0.90
0.70
0.40
0.10
1.10
0.80
0.46
0.36
0.26
0.22
0.08
SEATING
PLANE
0.10 MAX
0.30
0.15
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-203-AB
Figure 29. 6-Lead Thin Shrink Small Outline Transistor Package (SC70)
(KS-6)
Dimensions shown in millimeters
3.20
3.00
2.80
8
1
5
4
5.15
4.90
4.65
3.20
3.00
2.80
PIN 1
IDENTIFIER
0.65 BSC
0.95
0.85
0.75
15° MAX
1.10 MAX
0.80
0.55
0.40
0.15
0.05
0.23
0.09
6°
0°
0.40
0.25
COPLANARITY
0.10
COMPLIANT TO JEDEC STANDARDS MO-187-AA
Figure 30. 8-Lead Mini Small Outline Package (MSOP)
(RM-8)
Dimensions shown in millimeters
Rev. A | Page 15 of 16
ADCMP600/ADCMP601/ADCMP602
ORDERING GUIDE
Model1
Temperature Range
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
Package Description
5-Lead SOT23
5-Lead SOT23
5-Lead SOT23
5-Lead SC70
Package Option
RJ-5
RJ-5
RJ-5
KS-5
Branding
G0C
G0C
G0C
G0C
G0C
G0C
G0N
G0N
G0N
GF
ADCMP600BRJZ-R2
ADCMP600BRJZ-RL
ADCMP600BRJZ-REEL7
ADCMP600BKSZ-R2
ADCMP600BKSZ-RL
ADCMP600BKSZ-REEL7
ADCMP601BKSZ-R2
ADCMP601BKSZ-RL
ADCMP601BKSZ-REEL7
ADCMP602BRMZ
ADCMP602BRMZ-REEL
ADCMP602BRMZ-REEL7
EVAL-ADCMP600BRJZ
EVAL-ADCMP600BKSZ
EVAL-ADCMP601BKSZ
EVAL-ADCMP602BRMZ
5-Lead SC70
5-Lead SC70
KS-5
KS-5
6-Lead SC70
6-Lead SC70
6-Lead SC70
KS-6
KS-6
KS-6
8-Lead MSOP
8-Lead MSOP
8-Lead MSOP
Evaluation Board
Evaluation Board
Evaluation Board
Evaluation Board
RM-8
RM-8
RM-8
GF
GF
1 Z = RoHS Compliant Part.
©2006–2011 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D05914-0-1/11(A)
Rev. A | Page 16 of 16
相关型号：
©2020 ICPDF网 联系我们和版权申明