EVAL-ADT7466EB [ADI]
dBCool Remote Thermal Controller and Voltage Monitor; dBCool远程热控制器和电压监视器
| 型号： | EVAL-ADT7466EB |
| 厂家： | 
ADI |
| 描述： | dBCool Remote Thermal Controller and Voltage Monitor |
| 文件： | 总48页 (文件大小：1472K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
dBCool® Remote Thermal
Controller and Voltage Monitor
ADT7466
FEATURES
GENERAL DESCRIPTION
Monitors two analog voltages or thermistor temperature
inputs
One on-chip and up to two remote temperature sensors with
series resistance cancellation
Controls and monitors the speed of up to two fans
Automatic fan speed control mode controls system
cooling based on measured temperature
Enhanced acoustic mode dramatically reduces user
perception of changing fan speeds
Thermal protection feature via THERM output monitors
performance impact of Intel® Pentium® 4 processor
thermal control circuit via PROCHOT input
3-wire fan speed measurement
Limit comparison of all monitored values
SMBus 1.1 serial interface
The ADT7466 dBCool controller is a complete thermal monitor
and dual fan controller for noise-sensitive applications
requiring active system cooling. It can monitor two analog
voltages or the temperature of two thermistors, plus its own
supply voltage. It can monitor the temperature of up to two
remote sensor diodes, plus its own internal temperature. It can
measure and control the speed of up to two fans so that they
operate at the lowest possible speed for minimum acoustic
noise. The automatic fan speed control loop optimizes fan
speed for a given temperature. The effectiveness of the system’s
thermal solution can be monitored using the
input
PROCHOT
to time and monitor the
output of the processor.
PROCHOT
APPLICATIONS
Low acoustic noise notebook PCs
FUNCTIONAL BLOCK DIAGRAM
V
SCL SDA ALERT
CC
SERIAL BUS
INTERFACE
8-BIT
DRIVE1
DAC
ACOUSTIC
ENHANCEMENT
CONTROL
V_FAN_MIN
V_FAN_ON
CONTROL
ADDRESS
POINTER
REGISTER
8-BIT
DRIVE2
DAC
AUTOMATIC
FAN SPEED
CONTROL
CONFIGURATION
REGISTERS
TACH1
FAN
THERM
REGISTER
TACH2
SPEED
MONITOR
FANLOCK
INTERRUPT
MASKING
FAN1
ENABLE
FAN1_ON/
PROCHOT/
THERM
INTERRUPT
STATUS
REGISTERS
PROCHOT
LIMIT
SERIES
D1+
D1–
RESISTANCE
COMPARATORS
10-BIT
ADC
CANCELLATION
INPUT
SIGNAL
VALUE AND
LIMIT
REGISTERS
SERIES
RESISTANCE
CANCELLATION
AIN1/TH1/D2–
AIN2/TH2/D2+
CONDITIONING
AND
ANALOG
MULTIPLEXER
BAND GAP
REFERENCE
BAND GAP
TEMPERATURE
SENSOR
ADT7466
GND
REFOUT
Figure 1.
Protected by U.S. Patent Numbers 6,188,189; 6,169,442; 6,097,239; 5,982,221; 5,867,012.
Rev. 0
Information furnished by Analog Devices is believed to be accurate and reliable.
However, no responsibility is assumed by Analog Devices for its use, nor for any
infringements of patents or other rights of third parties that may result from its use.
Specifications subject to change without notice. No license is granted by implication
or otherwise under any patent or patent rights of Analog Devices. Trademarks and
registered trademarks are the property of their respective owners.
One Technology Way, P.O. Box 9106, Norwood, MA 02062-9106, U.S.A.
Tel: 781.329.4700
Fax: 781.461.3113
www.analog.com
© 2005 Analog Devices, Inc. All rights reserved.
ADT7466
TABLE OF CONTENTS
Specifications..................................................................................... 3
Series Resistance Cancellation.................................................. 17
Temperature Measurement Method........................................ 17
Using Discrete Transistors ........................................................ 17
Temperature Measurement Using Thermistors ..................... 19
Reading Temperature from the ADT7466.............................. 20
Additional ADC Functions....................................................... 21
Limit Values ................................................................................ 21
Alert Interrupt Behavior............................................................ 23
Serial Bus Timing ......................................................................... 5
Absolute Maximum Ratings............................................................ 6
Thermal Characteristics .............................................................. 6
ESD Caution.................................................................................. 6
Pin Configuration and Function Descriptions............................. 7
Typical Performance Characteristics ............................................. 8
Functional Description.................................................................. 11
Measurement Inputs .................................................................. 11
Sequential Measurement ........................................................... 11
Fan Speed Measurement and Control ..................................... 11
Internal Registers of the ADT7466 .......................................... 11
Theory of Operation ...................................................................... 12
Serial Bus Interface..................................................................... 12
Write and Read Operations....................................................... 14
Alert Response Address (ARA)................................................ 15
SMBus Timeout .......................................................................... 15
Voltage Measurement ................................................................ 15
Reference Voltage Output.......................................................... 16
Configuration of Pin 11 and Pin 12......................................... 16
Temperature Measurement ....................................................... 17
THERM
Configuring the ADT7466
Pin as an Output......... 25
Fan Drive ..................................................................................... 26
PWM or Switch Mode Fan Drive............................................. 26
Fan Speed Measurement ........................................................... 26
Fan Start-Up Timeout................................................................ 28
Automatic Fan Speed Control .................................................. 29
Starting the Fan .......................................................................... 30
XOR Test Mode............................................................................... 31
Application Circuit......................................................................... 32
ADT7466 Register Map................................................................. 33
Register Details........................................................................... 35
Outline Dimensions....................................................................... 47
Ordering Guide .......................................................................... 47
REVISION HISTORY
6/05—Revision 0: Initial Version
Rev. 0 | Page 2 of 48
ADT7466
SPECIFICATIONS
TA = TMIN to TMAX, VCC = VMIN to VMAX, unless otherwise noted.1
Table 1.
Parameter
Min
Typ
Max
Unit Test Conditions/Comments
POWER SUPPLY
Supply Voltage
Supply Current, ICC
3.0
3.3
1.4
30
5.5
3
70
V
mA
µA
Interface inactive, ADC active
Standby mode, digital inputs low
TEMPERATURE-TO-DIGITAL
CONVERTER
Local Sensor Accuracy
1
3
°C
°C
20°C ≤ TA ≤ 60°C; VCC = 3.3 V
−40°C ≤ TA ≤ +125°C; VCC = 3.3 V
Resolution
0.25
°C
Remote Diode Sensor Accuracy
1
3
5
°C
°C
°C
20°C ≤ TA ≤ 60°C; −40°C ≤ TD ≤ +125°C; VCC = 3.3 V
−40°C ≤TA ≤ +105°C; −40°C ≤ TD ≤ +125°C; VCC = 3.3 V
−40°C ≤ TA ≤ +125°C; −40°C ≤ TD ≤ +125°C
Resolution
Remote Sensor Source Current
0.25
192
72
°C
µA
µA
µA
kΩ
High level
Mid level
Low level
12
Series Resistance Cancellation
0
2
Maximum resistance in series with thermal diode that can be
cancelled out
THERMISTOR-TO-DIGITAL CONVERTER
Temperature Range
30
100
°C
Range over which specified accuracy is achieved. Wider range
can be used with less accuracy.
Resolution
Accuracy
0.25
2
°C
°C
Using specified thermistor and application circuit over specified
temperature range
ANALOG-TO-DIGITAL CONVERTER
Input Voltage Range
Total Unadjusted Error (TUE)
Differential Nonlinearity (DNL)
Power Supply Sensitivity
Conversion Time (AIN Input)
Conversion Time (Local
Temperature)
0
VREF
2.5
1
V
%
LSB
%/V
ms
ms
VREF = 2.25V
1
1
8.30
8.63
8.65
8.99
Averaging enabled
Averaging enabled
Conversion Time (Remote
Temperature)
35.22
36.69
ms
Averaging enabled
Conversion Time (VCC)
Total Monitoring Cycle Time
7.93
68.38
8.26
71.24
ms
ms
Averaging enabled
Averaging enabled, Pin 11 and Pin 12 configured for AIN/TH
monitoring (see Table 15)
Total Monitoring Cycle Time
87
90.63
ms
Averaging enabled, Pin 11 and Pin 12 configured for REM2
monitoring (see Table 15)
FAN RPM-TO-DIGITAL CONVERTER
Accuracy
4
%
Full-Scale Count
65,535
Nominal Input RPM
109
329
5000
10000
RPM Fan count = 0xBFFF
RPM Fan count = 0x3FFF
RPM Fan count = 0x0438
RPM Fan count = 0x021C
kHz
Internal Clock Frequency
78.64 81.92
85.12
Rev. 0 | Page 3 of 48
ADT7466
Parameter
Min
Typ
Max
Unit Test Conditions/Comments
DRIVE OUTPUTS (DRIVE1, DRIVE2)
Output Voltage Range
Output Source Current
Output Sink Current
DAC Resolution
0–2.2
2
0.5
V
Digital input = 0x00 to 0xFF
mA
mA
Bits
Bits
LSB
LSB
%
8
8
Monotonicity
Differential Nonlinearity
Integral Nonlinearity
Total Unadjusted Error
1
5
1
IL = 2 mA
REFERENCE VOLTAGE OUTPUT
(REFOUT)
Output Voltage
Output Source Current
Output Sink Current
2.226 2.25
2.288
10
0.6
V
mA
mA
OPEN-DRAIN SERIAL DATA BUS
OUTPUT (SDA)
Output Low Voltage (VOL)
High Level Output Current (IOH)
0.4
1
V
µA
IOUT = −4.0 mA, VCC = 3.3 V
VOUT = VCC
0.1
DIGITAL INPUTS (SCL, SDA, TACH
INPUTS, PROCHOT)
Input High Voltage (VIH)
Input Low Voltage (VIL)
Hysteresis
2.0
V
V
V
0.8
1
0.5
DIGITAL INPUT CURRENT (TACH
INPUTS, PROCHOT)
Input High Current (IIH)
Input Low Current (IIL)
Input Capacitance (IN)
−1
µA
µA
pF
VIN = VCC
VIN = 0
20
OPEN-DRAIN DIGITAL OUTPUTS
(ALERT, FANLOCK, FAN1_ON/THERM)
Output Low Voltage (VOL)
High Level Output Current (IOH)
SERIAL BUS TIMING 2
0.4
1
V
µA
IOUT = −4.0 mA, VCC = 3.3 V
VOUT =VCC
0.1
Clock Frequency (fSCLK
Glitch Immunity (tSW)
)
400
50
kHz
ns
µs
µs
µs
µs
µs
ns
ns
ns
Ms
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
See Figure 2
Bus Free Time (tBUF
Start Setup Time (tSU;STA
Start Hold Time (tHD;STA
SCL Low Time (tLOW
SCL High Time (tHIGH
)
1.3
0.6
0.6
1.3
0.6
)
)
)
)
SCL, SDA Rise Time (tr)
SCL, SDA Fall Time (tf )
Data Setup Time (tSU;DAT
1000
300
See Figure 2
See Figure 2
Can be optionally disabled
)
100
25
Detect Clock Low Timeout (tTIMEOUT
)
64
1 All voltages are measured with respect to GND, unless otherwise specified. Typical values are at TA = 25°C and represent the most likely parametric norm. Logic inputs
accept input high voltages up to 5 V even when the device is operating at supply voltages below 5 V. Timing specifications are tested at logic levels of VIL = 0.8 V for a
falling edge and at VIH = 2.0 V for a rising edge.
2 Guaranteed by design, not production tested.
Rev. 0 | Page 4 of 48
ADT7466
SERIAL BUS TIMING
tR
tF
tHD;STA
tLOW
SCL
SDA
tHD;STA
tHD;DAT
tHIGH
tSU;STA
tSU;STO
tSU;DAT
tBUF
P
S
S
P
Figure 2. Diagram for Serial Bus Timing
Rev. 0 | Page 5 of 48
ADT7466
ABSOLUTE MAXIMUM RATINGS
Table 2.
Stresses greater than those listed under Absolute Maximum
Ratings may cause permanent damage to the device. This is a
stress rating only and functional operation of the device at these
or any other conditions above those indicated in the operational
section of this specification is not implied. Exposure to absolute
maximum rating conditions for extended periods may affect
device reliability.
Parameter
Rating
Positive Supply Voltage (VCC)
Voltage on Any Other Pin
Input Current at Any Pin
Package Input Current
6.5 V
−0.3 V to 6.5 V
5 mA
20 mA
Maximum Junction Temperature (TJ max)
Storage Temperature Range
Lead Temperature, Soldering:
IR Peak Reflow Temperature
Lead Temperature (10 sec)
ESD Rating
150°C
−65°C to +150°C
THERMAL CHARACTERISTICS
16-Lead QSOP Package:
θJA = 105°C/W
220°C
300°C
2000 V
θJC = 39°C/W
ESD CAUTION
ESD (electrostatic discharge) sensitive device. Electrostatic charges as high as 4000 V readily accumulate on
the human body and test equipment and can discharge without detection. Although this product features
proprietary ESD protection circuitry, permanent damage may occur on devices subjected to high energy
electrostatic discharges. Therefore, proper ESD precautions are recommended to avoid performance degrada-
tion or loss of functionality.
Rev. 0 | Page 6 of 48
ADT7466
PIN CONFIGURATION AND FUNCTION DESCRIPTIONS
DRIVE1
TACH1
DRIVE2
TACH2
GND
1
2
3
4
5
6
7
8
16 SCL
15 SDA
14 ALERT
13 REFOUT
12 AIN2/TH2/D2+
11 AIN1/TH1/D2–
10 D1+
ADT7466
TOP VIEW
(Not to Scale)
V
CC
FAN1_ON/PROCHOT/THERM
FANLOCK
9
D1–
Figure 3. Pin Configuration
Table 3. Pin Function Descriptions
Pin No. Mnemonic Type
Description
1
2
3
4
DRIVE1
TACH1
DRIVE2
TACH2
Analog
Output
Digital
Input
Analog
Output
Digital
Input
Output of 8-Bit DAC Controlling Fan 1 Speed.
Fan Tachometer Input to Measure Speed of Fan 1.
Output of 8-Bit DAC Controlling Fan 2 Speed.
Fan Tachometer Input to Measure Speed of Fan 2.
5
6
GND
VCC
Ground
Power
supply
Ground Pin for Analog and Digital Circuitry.
3.3 V Power Supply. VCC is also monitored through this pin.
7
FAN1_ON/ PROCHOT/ Digital I/O
THERM
If configured as FAN1_ON, this pin is the open-drain control signal output for the dc-dc
converter. Active (high) when DRIVE1 > V_FAN_MIN.
If configured as PROCHOT, the input can be connected to the PROCHOT output of the
Intel Pentium 4 processor to time and monitor PROCHOT assertions.
If configured as THERM, this pin is the interrupt output to flag critical thermal events.
8
FANLOCK
D1−
Digital
Output
Analog
Input
Open-Drain Digital Output. This output is asserted (low) when either of the fans stall or
fail to spin up.
Cathode Connection to Thermal Diode 1.
9
10
11
12
13
14
D1+
Analog
Input
Analog
input
Analog
Input
Analog
Output
Anode Connection to Thermal Diode 1.
AIN1/TH1/D2−
AIN2(TH2)/D2+
REFOUT
0 V to 2.25 V Analog Input. Can be reconfigured as thermistor input or as a cathode
connection to Thermal Diode 2. Configured for thermistor connection by default.
0 V to 2.25 V Analog Input. Can be reconfigured as thermistor input or as an anode
connection to Thermal Diode 2. Configured for thermistor connection by default.
2.25 V Reference Voltage Output, 20 mA maximum output current.
ALERT
Digital
Output
Open-Drain Digital Output. The SMBus ALERT pin alerts the system to out-of-limit events
such as a failed fan, overtemperature, or out-of-limit analog measurement.
15
16
SDA
SCL
Digital I/O
Digital
Input
Open-Drain Digital I/O. SMBus bidirectional serial data. Requires SMBus pull-up resistor.
Open-Drain Digital Input. SMBus serial clock input. Requires SMBus pull-up resistor.
Rev. 0 | Page 7 of 48
ADT7466
TYPICAL PERFORMANCE CHARACTERISTICS
20
0
–10
–20
–30
–40
–50
–60
–70
10
D+ TO GND
DEVICE 1
DEVICE 2
0
–10
–20
DEVICE 3
D+ TO V
CC
–30
–40
–50
–60
0
20
40
60
80
100
0
5
10
15
20
25
LEAKAGE RESISTANCE (MΩ)
CAPACITANCE (nF)
Figure 4. Temperature Error vs. PCB Track Resistance
Figure 7. Temperature Error vs. Capacitance Between D+ and D−
20
15
10
5
40
35
100mV
30
25
20
15
10
100mV
250mV
0
60mV
5
–5
–10
0
40mV
–5
0
1
2
3
4
5
6
0
1
2
3
4
5
6
NOISE FREQUENCY (MHz)
NOISE FREQUENCY (MHz)
Figure 5. Remote Temperature Error vs. Power Supply Noise Frequency
Figure 8. Remote Temperature Error vs. Common-Mode Noise Frequency
35
30
25
20
15
90
80
70
60
50
40
30
20
10
250mV
5
0
–5
100mV
60mV
100mV
–10
10
0
–15
–20
40mV
–10
0
1
2
3
4
5
6
0
1
2
3
4
5
6
NOISE FREQUENCY (MHz)
NOISE FREQUENCY (MHz)
Figure 6. Local Temperature Error vs. Power Supply Noise Frequency
Figure 9. Remote Temperature Error vs. Differential Mode Noise Frequency
Rev. 0 | Page 8 of 48
ADT7466
7
6
5
4
3
2
1
0
140
120
100
80
EXTERNAL
DEVICE 2
DEVICE 3
DEVICE 1
INTERNAL
60
40
20
0
3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
(V)
0
10
20
30
TIME (s)
40
50
60
V
DD
Figure 13. Response to Thermal Shock
Figure 10. Standby Supply Current vs. Supply Voltage
1.00
0.99
0.98
0.97
0.96
0.95
0.94
0.93
0.92
0.91
0.90
0.89
16
14
12
10
8
DEVICE 1
DEVICE 3
DEVICE 1
DEVICE 3
6
DEVICE 2
4
DEVICE 2
2
0
3.0 3.2 3.4 3.6 3.8 4.0 4.2 4.4 4.6 4.8 5.0 5.2 5.4
(V)
0
50
100
150
200
250
300
350
400
V
SCL FREQUENCY (kHz)
DD
Figure 11. Standby Current vs. Clock Frequency
Figure 14. Supply Current vs. Supply Voltage
120
100
80
2
1
HIGH SPEC
0
60
–1
–2
–3
–4
–5
–6
MEAN
40
20
0
–20
–40
LOW SPEC
–40
–20
0
20
40
60
80
100
120
–40
0
20
40
60
85
105
125
ACTUAL TEMPERATURE (°C)
TEMPERATURE (°C)
Figure 12. Pentium 4 Temperature Measurement vs. ADT7466 Reading
Figure 15. Local Temperature Error
Rev. 0 | Page 9 of 48
ADT7466
2
1
HIGH SPEC
MEAN
0
–1
–2
–3
–4
LOW SPEC
105 125
–5
–40
0
20
40
60
85
TEMPERATURE (°C)
Figure 16. Remote Temperature Error
Rev. 0 | Page 10 of 48
ADT7466
FUNCTIONAL DESCRIPTION
The ADT7466 is a complete thermal monitor and dual fan
controller for any system requiring monitoring and cooling.
The device communicates with the system via a serial system
management bus (SMBus). The serial data line (SDA, Pin 15) is
used for reading and writing addresses and data. The input line,
(SCL, Pin 16) is the serial clock. All control and programming
functions of the ADT7466 are performed over the serial bus. In
The device also accepts input from an on-chip band gap
temperature sensor that monitors system ambient temperature.
Power is supplied to the chip via Pin 6. The system also
monitors VCC through this pin. It is normally connected to a
3.3 V supply. It can, however, be connected to a 5 V supply and
monitored without going over range.
addition, an
conditions.
output is provided to indicate out-of-limit
ALERT
SEQUENTIAL MEASUREMENT
When the ADT7466 monitoring sequence is started, it
sequentially cycles through the measurement of analog inputs
and the temperature sensors. Measured values from these
inputs are stored in value registers, which can be read out over
the serial bus, or can be compared with programmed limits
stored in the limit registers. The results of out of limit
comparisons are stored in the status registers, which can be read
over the serial bus to flag out-of-limit conditions.
MEASUREMENT INPUTS
The device has three measurement inputs, two for voltage and
one for temperature. It can also measure its own supply voltage
and can measure ambient temperature with its on-chip
temperature sensor.
Pin 11 and Pin 12 are analog inputs with an input range of 0 V
to 2.25 V. They can easily be scaled for other input ranges by
using external attenuators. These pins can also be configured
for temperature monitoring by using thermistors or a second
remote diode temperature measurement.
FAN SPEED MEASUREMENT AND CONTROL
The ADT7466 has two tachometer inputs for measuring the
speed of 3-wire fans, and it has two 8-bit DACs to control the
speed of two fans. The temperature measurement and fan speed
control can be linked in an automatic control loop, which can
operate without CPU intervention to maintain system operating
temperature within acceptable limits. The enhanced acoustics
feature ensures that fans operate at the minimum possible speed
consistent with temperature control, and change speed
gradually. This reduces the user’s perception of changing fan
speed.
The ADT7466 can simultaneously monitor the local
temperature, the remote temperature by using a discrete
transistor, and two thermistor temperatures.
Remote temperature sensing is provided by the D+ and D−
inputs, to which diode connected, remote temperature sensing
transistors such as a 2N3904 or CPU thermal diode can be
connected.
INTERNAL REGISTERS OF THE ADT7466
Temperature sensing using thermistors is carried out by placing
the thermistor in series with a resistor. The excitation voltage is
provided by the REFOUT pin.
Table 4 provides brief descriptions of the ADT7466’s principal
internal registers. More detailed information on the function of
each register is given in Table 30 to Table 72.
Table 4. Internal Register Summary
Register
Description
Configuration
Address Pointer
These registers provide control and configuration of the ADT7466 including alternate pinout functionality.
This register contains the address that selects one of the other internal registers. When writing to the ADT7466, the
first byte of data is always a register address, which is written to the address pointer register.
Status
These registers provide status of each limit comparison and are used to signal out-of-limit conditions on the
temperature, voltage, or fan speed channels. Whenever a status bit is set, the ALERT output (Pin 14) goes low.
Interrupt Mask
Value and Limit
These registers allow interrupt sources to be masked so that they do not affect the ALERT output.
The results of analog voltage inputs, temperature, and fan speed measurements are stored in these registers, along
with their limit values.
Offset
These registers allow each temperature channel reading to be offset by a twos complement value written to these
registers.
PROCHOT Status
This register allows the ADT7466 to monitor and time any PROCHOT events gauging system performance.
These registers program the starting temperature for each fan under automatic fan speed control.
TMIN
TRANGE
These registers program the temperature-to-fan speed control slope in automatic fan speed control mode for each
fan drive output.
Enhance Acoustics
This register sets the step size for fan drive changes in AFC mode to minimize acoustic noise.
Rev. 0 | Page 11 of 48
ADT7466
THEORY OF OPERATION
write operation is limited only by what the master and slave
devices can handle.
SERIAL BUS INTERFACE
The serial system management bus (SMBus) is used to control
the ADT7466. The ADT7466 is connected to this bus as a slave
device under the control of a master controller.
When all data bytes have been read or written, stop conditions
are established. In write mode, the master pulls the data line
high during the 10th clock pulse to assert a stop condition. In
read mode, the master device overrides the acknowledge bit by
pulling the data line high during the low period before the
ninth clock pulse. This is known as No Acknowledge. The
master takes the data line low during the low period before the
10th clock pulse, and then high during the 10th clock pulse to
assert a stop condition.
The ADT7466 has an SMBus timeout feature. When this is
enabled, the SMBus times out after typically 25 ms of no
activity. However, this feature is enabled by default. Bit 5 of
Configuration Register 1 (0x00) should be set to 1 to disable
this feature.
The ADT7466 supports optional packet error checking (PEC).
It is triggered by supplying the extra clock pulses for the PEC
byte. The PEC byte is calculated using CRC-8. The frame check
sequence (FCS) conforms to CRC-8 by the polynomial
Any number of bytes of data can be transferred over the serial
bus in one operation, but it is not possible to mix read and write
in one operation, because the type of operation is determined at
the beginning and subsequently cannot be changed without
starting a new operation.
C x = x8 + x2 + x1+1
( )
Consult the SMBus Specifications Rev. 1.1 for more information
(www.smbus.org).
ADT7466 write operations contain either one or two bytes, and
read operations contain one byte, and perform the following
functions.
The ADT7466 has a 7-bit serial bus address, which is fixed at
1001100.
To write data to one of the device data registers or read data
from it, the address pointer register must be set so that the
correct data register is addressed, and data can be written to
that register or read from it. The first byte of a write operation
always contains an address that is stored in the address pointer
register. If data is to be written to the device, the write operation
contains a second data byte that is written to the register
selected by the address pointer register. This is shown in
Figure 17. The device address is sent over the bus followed by
The serial bus protocol operates as follows:
The master initiates data transfer by establishing a start condition,
defined as a high-to-low transition on the serial data line SDA
while the serial clock line SCL remains high. This indicates that
an address/data stream follows. All slave peripherals connected
to the serial bus respond to the start condition, and shift in the
next 8 bits, consisting of a 7-bit address (MSB first) and a R/
bit, which determines the direction of the data transfer, that is,
whether data is written to or read from the slave device.
W
R/ set to 0. This is followed by two data bytes. The first data
W
byte is the address of the internal data register to be written to,
which is stored in the address pointer register. The second data
byte is the data to be written to the internal data register.
The address of the ADT7466 is set at 1001100. Since the address
must always be followed by a write bit (0) or a read bit (1), and
data is generally handled in 8-bit bytes, it may be more conven-
ient to think that the ADT7466 has an 8-bit write address of
10011000 (0x98) and an 8-bit read address of 10011001 (0x99).
The peripheral whose address corresponds to the transmitted
address responds by pulling the data line low during the low
period before the 9th clock pulse, known as the acknowledge
bit. All other devices on the bus now remain idle while the
selected device waits for data to be read from or written to it. If
When reading data from a register, there are two possibilities.
If the ADT7466 address pointer register value is unknown or
not the desired value, it is necessary to first set it to the correct
value before data can be read from the desired data register.
This is done by performing a write to the ADT7466 as before,
but only the data byte containing the register address is sent
since data is not to be written to the register. This is shown in
Figure 18.
the R/ bit is 0, the master writes to the slave device. If the
W
R/ bit is 1, the master reads from the slave device.
W
A read operation is then performed consisting of the serial bus
Data is sent over the serial bus in sequences of 9 clock pulses,
8 bits of data followed by an acknowledge bit from the slave
device. Transitions on the data line must occur during the low
period of the clock signal and remain stable during the high
period, because a low-to-high transition when the clock is high
may be interpreted as a stop signal. The number of data bytes
that can be transmitted over the serial bus in a single read or
address, R/ bit set to 1, followed by the data byte read from
W
the data register. This is shown in Figure 19.
If the address pointer register is known to already be at the
desired address, data can be read from the corresponding data
register without first writing to the address pointer register, so
the procedure in Figure 18 can be omitted.
Rev. 0 | Page 12 of 48
ADT7466
1
9
1
9
SCL
SDA
1
0
0
1
1
0
0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
START BY
MASTER
ACK. BY
ADT7466
ACK. BY
ADT7466
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
1
9
SCL (CONTINUED)
SDA (CONTINUED)
D7
D6
D5
D4
D3
D2
D1
D0
ACK. BY STOP BY
ADT7466 MASTER
FRAME 3 DATA BYTE
Figure 17. Writing a Register Address to the Address Pointer Register, then Writing Data to the Selected Register
1
9
1
9
SCL
SDA
1
0
0
1
1
0
0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
START BY
MASTER
ACK. BY
ADT7466
ACK. BY STOP BY
ADT7466 MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 18. Writing to the Address Pointer Register Only
1
1
9
1
9
SCL
0
0
1
1
0
0
R/W
D7
D6
D5
D4
D3
D2
D1
D0
SDA
START BY
ACK. BY
ADT7466
NO ACK. BY STOP BY
MASTER MASTER
MASTER
FRAME 1
SERIAL BUS ADDRESS BYTE
FRAME 2
ADDRESS POINTER REGISTER BYTE
Figure 19. Reading Data from a Previously Selected Register
Although it is possible to read a data byte from a data register
without first writing to the address pointer register if the
address pointer register is already at the correct value, it is not
possible to write data to a register without writing to the address
pointer register, because the first data byte of a write is always
written to the address pointer register.
In addition to supporting the send byte and receive byte
protocols, the ADT7466 also supports the read byte protocol
(see the SMBus Specifications Rev. 1.1 for more information).
If it is required to perform several read or write operations in
succession, the master can send a repeat start condition instead
of a stop condition to begin a new operation.
Rev. 0 | Page 13 of 48
ADT7466
Write Byte
WRITE AND READ OPERATIONS
In this operation, the master device sends a command byte and
one data byte to the slave device, as follows:
The SMBus specification defines several protocols for different
types of write and read operations. The protocols used in the
ADT7466 are discussed in the following sections. The following
abbreviations are used in the diagrams:
1. The master device asserts a start condition on SDA.
2. The master sends the 7-bit slave address followed by the
write bit (low).
S—Start
P—Stop
R—Read
W—Write
A—Acknowledge
3. The addressed slave device asserts ACK on SDA.
4. The master sends a register address.
5. The slave asserts ACK on SDA.
A
—No Acknowledge
Write Operations
6. The master sends a data byte.
The ADT7466 uses the send byte and write byte protocols.
7. The slave asserts ACK on SDA.
Send Byte
In this operation, the master device sends a single command
byte to a slave device, as follows:
8. The master asserts a stop condition on SDA to end the
transaction.
1. The master device asserts a start condition on SDA.
This is shown in Figure 21.
2. The master sends the 7-bit slave address followed by the
write bit (low).
1
2
3
4
5
6
7
8
SLAVE
ADDRESS
REGISTER
ADDRESS
S
W
A
A
DATA
A
P
3. The addressed slave device asserts ACK on SDA.
4. The master sends a register address.
5. The slave asserts ACK on SDA.
Figure 21. Single-Byte Write to a Register
Read Operations
The ADT7466 uses the following SMBus read protocols.
6. The master asserts a stop condition on SDA and the
transaction ends.
Receive Byte
This is useful when repeatedly reading a single register. The
register address needs to have been set up previously.
For the ADT7466, the send byte protocol is used to write a
register address to RAM for a subsequent single-byte read from
the same address. This is shown in Figure 20.
In this operation, the master device receives a single byte from a
slave device, as follows:
1
2
3
4
5
6
1. The master device asserts a start condition on SDA.
SLAVE
ADDRESS
REGISTER
ADDRESS
S
W
A
A
P
2. The master sends the 7-bit slave address followed by the
read bit (high).
Figure 20. Setting a Register Address for Subsequent Read
3. The addressed slave device asserts ACK on SDA.
4. The master receives a data byte.
If it is required to read data from the register immediately after
setting up the address, the master can assert a repeat start con-
dition immediately after the final ACK and carry out a single-
byte read without asserting an intermediate stop condition.
5. The master asserts NO ACK on SDA.
6. The master asserts a stop condition on SDA and the
transaction ends.
For the ADT7466, the receive byte protocol is used to read a
single byte of data from a register whose address was set
previously by a send byte or write byte operation.
1
2
3
4
5
6
SLAVE
ADDRESS
S
R
A
DATA
A
P
Figure 22. Single-Byte Read from a Register
Rev. 0 | Page 14 of 48
ADT7466
produces an output of 3/4 full scale (decimal 768 or 0x300) for
the nominal supply voltage, and so has adequate headroom to
cope with overvoltages.
ALERT RESPONSE ADDRESS (ARA)
ARA is a feature of SMBus devices that allows an interrupting
device to identify itself to the host when multiple devices exist
Table 9 shows the input ranges of the analog inputs and the
output codes of the ADC.
on the same bus. The
output can be used as an interrupt
ALERT
output, or it can be used as an
. One or more outputs can
ALERT
Table 6. Voltage Measurement Registers
be connected to a common
line connected to the
ALERT
line goes low, the following occurs:
Register
Description
AIN1 reading
AIN2 reading
VCC reading
Default
0x00
0x00
master. If a device’s
ALERT
0x0A
0x0B
0x0C
1.
is pulled low.
ALERT
0x00
2. The master initiates a read operation and sends the alert
response address (ARA = 0001 100). This is a general call
address, which must not be used as a specific device
address.
Associated with each voltage measurement channel are high
and low limit registers. Exceeding the programmed high or low
limit causes the appropriate status bit to be set. Exceeding either
3. The device whose
output is low responds to the
ALERT
limit can also generate
interrupts.
ALERT
alert response address, and the master reads its device
address. The address of the device is now known, and it
can be interrogated in the usual way.
Table 7. Voltage Measurement Limit Registers
Register
0x14
0x15
0x16
0x17
Description
Default
0x00
0xFF
0x00
0xFF
4. If more than one device’s
output is low, the one
ALERT
AIN1 low limit
AIN1 high limit
AIN2 low limit
AIN2 high limit
VCC low limit
with the lowest device address has priority, in accordance
with normal SMBus arbitration.
5. Once the ADT7466 responds to the alert response address,
0x18
0x19
0x00
0xFF
the master must read the status registers, the
cleared only if the error condition no longer exists.
is
ALERT
VCC high limit
SMBus TIMEOUT
When the ADC is running, it samples and converts a voltage
input in 1 ms, and averages 16 conversions to reduce noise.
Therefore a measurement on each input takes nominally 16 ms.
The ADT7466 includes an SMBus timeout feature. If there is no
SMBus activity for 25 ms, the ADT7466 assumes that the bus is
locked, and it releases the bus. This prevents the device from
locking or holding the SMBus expecting data. Some SMBus
controllers cannot handle the SMBus timeout feature, so they
are disabled.
Turn Off Averaging
For each voltage measurement read from a value register, 16
readings have actually been made internally and the results
averaged, before being placed into the value register. There can
be an instance where faster conversions are required. Setting
Bit 4 of Configuration Register 2 (0x01) turns averaging off.
This effectively gives a reading 16 times faster (1 ms), but as a
result the reading can be noisier.
Table 5. Configuration Register 1—Register 0x00
Bit Address and Value
Description
<5> TODIS = 0
<5> TODIS = 1
SMBus timeout enabled (default)
SMBus timeout disabled
Single-Channel ADC Conversions
VOLTAGE MEASUREMENT
Setting Bit 3 of Configuration Register 4 (0x03) places the
ADT7466 into single-channel ADC conversion mode. In this
mode, the ADT7466 can be made to read a single voltage channel
only. If the internal ADT7466 clock is used, the selected input is
read every 1 ms. The appropriate ADC channel is selected by
writing to Bits 2:0 of Configuration Register 4 (0x03).
The ADT7466 has two external voltage measurement channels.
Pin 11 and Pin 12 are analog inputs with a range of 0 V to
2.25 V. It can also measure its own supply voltage, VCC. The VCC
supply voltage measurement is carried out through the VCC pin
(Pin 6). Setting Bit 6 of Configuration Register 1 (0x00) allows a
5 V supply to power the ADT7466 and be measured without
overranging the VCC measurement channel.
Table 8. Single-Channel ADC Conversions
Bits 2:0, Reg. 0x03
Channel Selected
A/D Converter
000
001
010
AIN1
AIN2
VCC
All analog inputs are multiplexed into the on-chip, successive
approximation, analog-to-digital converter. This has a resolution
of 10 bits. The basic input range is 0 V to 2.25 V, but the VCC
input has built in attenuators to allow measurement of 3.3 V or
5 V. To allow for the tolerance of the supply voltage, the ADC
Rev. 0 | Page 15 of 48
ADT7466
appropriate bits in the configuration registers. Bits 6:7 of
Configuration Register 3 (0x02) configure the device for either
analog inputs or thermistor inputs. Bit 7 of Configuration
Register 2 (0x01) configures Pin 11 and Pin 12 for the
connection of a second thermal diode. Bits 2:3 of Interrupt
Status Register 2 (0x11) indicate either an open or short circuit
on Thermal Diode 1 and Diode 2 inputs. Bits 4:5 of Interrupt
Status Register 2 (0x11) indicate either an open or short circuit
on TH1 and TH2 inputs. It is advisable to mask interrupts on
diode open/short alerts when in thermistor monitoring mode
and to mask interrupts on thermistor open/short alerts when in
REM2 mode.
REFERENCE VOLTAGE OUTPUT
The ADT7466 has a reference voltage of 2.25 V, which is
available on Pin 13 of the device. It can be used for scaling and
offsetting the analog inputs to give different voltage ranges. It
can also be used as an excitation voltage for a thermistor when
the analog inputs are configured as thermistor inputs. See the
Temperature Measurement section for more details.
CONFIGURATION OF PIN 11 AND PIN 12
Pin 11 and Pin 12 can be used for analog inputs, thermistor
inputs, or connecting a second remote thermal diode. The
ADT7466 is configured for thermistor connection by default.
The device is configured for the different modes by setting the
Table 9. A-to-D Output Code vs. VIN
VCC 3.3 V
VCC 5 V
AIN
Decimal
Binary
<0.0172
<0.026
<0.0088
0
1
2
3
00000000
00000001
00000010
00000011
01000000
10000000
11000000
11111100
11111101
11111110
11111111
0.017–0.034
0.034–0.052
0.052–0.069
1.110–1.127
2.220–2.237
3.3–3.347
4.371–4.388
4.388–4.405
4.405–4.423
>4.423
0.026–0.052
0.052–0.078
0.078–0.104
1.667–1.693
3.333–3.359
5–5.026
0.0088–0.0176
0.0176–0.0264
0.0264–0.0352
0.563–0.572
1.126–1.135
1.689–1.698
2.218–2.226
2.226–2.235
2.235–2.244
>2.244
64 (¼ scale)
128 (½ scale)
192 (¾ scale)
252
253
254
6.563–6.589
6.589–6.615
6.615–6.641
>6.634
255
Table 10. Mode Configuration Summary
Configuration
Register Settings
Mode
Limits
Alerts1
Description
Thermistor Mode
Default mode. Mask interrupts on diode NC.
(Set Bits 2:3 of Reg. 0x13.)
TH1
TH2
Register 0x02
Bit 7 = 1
Register 0x02
Bit 6 = 1
Low: Reg 0x14
High: Reg 0x15
Low: Reg 0x16
High: Reg 0x17
OOL: Reg. 0x10, Bit 6
NC: Reg. 0x11, Bit 4
OOL: Reg. 0x10, Bit 5
NC: Reg. 0x11, Bit 5
AIN Mode
AIN1
Ensure that AFC is not on. (Clear Bits 0:1 of
AFC Configuration Register 1, 0x05.)
Register 0x 02
Bit 7 = 0
Register 0x02
Bit 6 = 0
Low: Reg 0x14
High: Reg 0x15
Low: Reg 0x16
High: Reg 0x17
Low: Reg 0x14
High: Reg 0x15
OOL: Reg. 0x10, Bit 6
OOL: Reg. 0x10, Bit 5
AIN2
Remote 2 Diode Mode Register 0x01
Bit 7 = 1
OOL: Reg. 0x10, Bit 6 Mask interrupts on thermistor NC. (Set
Bits 4:5 of Reg. 0x13) and AIN2 (Bit 5 of
Reg. 0x12.)
NC: Reg. 0x11, Bit 3
1 OOL = Out of limit. NC = No connection.
Rev. 0 | Page 16 of 48
ADT7466
collector is not grounded, and should be linked to the base. To
prevent ground noise from interfering with the measurement,
the more negative terminal of the sensor is not referenced to
ground but is biased above ground by an internal diode at the
D– input. If the sensor is operating in an extremely noisy
environment, C1 may optionally be added as a noise filter. Its
value should never exceed 1000 pF. See the Layout
TEMPERATURE MEASUREMENT
The ADT7466 has two dedicated temperature measurement
channels, one for measuring the temperature of an on-chip
band gap temperature sensor, and one for measuring the
temperature of a remote diode, usually located in the CPU. In
addition, the analog input channels, AIN1 and AIN2, can be
reconfigured to measure the temperature of a second diode by
setting Bit 7 of Configuration Register 2 (0x01), or to measure
temperature using thermistors by setting Bit 6 and/or Bit 7 of
Configuration Register 3 (0x02).
Considerations section for more information on C1.
To measure ΔVBE, the operating current through the sensor is
switched between three related currents. Figure 24 shows N1 × I
and N2 × I as different multiples of the current I. The currents
through the temperature diode are switched between I and
N1 × I, giving ΔVBE1, and then between I and N2 × I, giving
ΔVBE2. The temperature can then be calculated using the two
ΔVBE measurements. This method can also cancel the effect of
series resistance on the temperature measurement. The
resulting ΔVBE waveforms are passed through a 65 kHz low-pass
filter to remove noise, and then to a chopper-stabilized
amplifier. This amplifies and rectifies the waveform to produce
a dc voltage proportional to ΔVBE. The ADC digitizes this
voltage, and a temperature measurement is produced. To reduce
the effects of noise, digital filtering is performed by averaging
the results of 16 measurement cycles for low conversion rates.
Signal conditioning and measurement of the internal
SERIES RESISTANCE CANCELLATION
Parasitic resistance, seen in series with the remote diode
between the D+ and D− inputs to the ADT7466, is caused by a
variety of factors including PCB track resistance and track
length. This series resistance appears as a temperature offset in
the sensor’s temperature measurement. This error typically
causes a 1°C offset per ohm of parasitic resistance in series with
the remote diode. The ADT7466 automatically cancels the
effect of this series resistance on the temperature reading, giving
a more accurate result without the need for user characterization
of the resistance. The ADT7466 is designed to automatically
cancel typically 2 kΩ of resistance. This is done transparently to
the user, using an advanced temperature measurement method
described in the following section.
temperature sensor is performed in the same manner.
USING DISCRETE TRANSISTORS
TEMPERATURE MEASUREMENT METHOD
If a discrete transistor is used, the collector is not grounded and
should be linked to the base. If an NPN transistor is used, the
emitter is connected to the D− input and the base to the D+
input. If a PNP transistor is used, the base is connected to the
D− input and the emitter to the D+ input. Figure 23 shows how
to connect the ADT7466 to an NPN or PNP transistor for
temperature measurement. To prevent ground noise interfering
with the measurement, the more negative terminal of the sensor
is not referenced to ground, but is biased above ground by an
internal diode at the D− input.
A simple method of measuring temperature is to exploit the
negative temperature coefficient of a diode, by measuring the
base emitter voltage (VBE) of a transistor operated at constant
current. Unfortunately, this technique requires calibration to
null out the effect of the absolute value of VBE, which varies
from device to device.
The technique used in the ADT7466 measures the change in
VBE when the device is operated at three different currents.
Previous devices used only two operating currents, but it is the
third current that allows series resistance cancellation.
ADT7466
ADT7466
Figure 24 shows the input signal conditioning used to measure
the output of a remote temperature sensor. This figure shows
the remote sensor as a substrate transistor, provided for
temperature monitoring on some microprocessors, but it could
also be a discrete transistor. If a discrete transistor is used, the
2N3904
NPN
D+
D+
2N3906
PNP
D–
D–
Figure 23. Connections for NPN and PNP Transistors
V
DD
I
BIAS
I
N1
×
I
N2 × I
V
OUT+
D+
TO ADC
REMOTE
SENSING
TRANSISTOR
C1*
D–
BIAS
DIODE
V
OUT–
LOW-PASS FILTER
fC = 65kHz
*CAPACITOR C1 IS OPTIONAL. IT SHOULD ONLY BE USED IN NOISY ENVIRONMENTS.
Figure 24. Signal Conditioning for Remote Diode Temperature Sensors
Rev. 0 | Page 17 of 48
ADT7466
Temperature Data Format
Nulling Out Temperature Errors
The temperature data stored in the temperature data registers
consists of a high byte with an LSB size equal to 1°C. If higher
resolution is required, two additional bits are stored in the
extended temperature registers, giving a resolution of 0.25°C.
The temperature measurement range for both local and remote
measurements is, by default, 0°C to 127°C (binary), so the ADC
output code equals the temperature in degrees Celsius, and half
the range of the ADC is not actually used.
The ADT7466 automatically nulls out temperature
measurement errors due to series resistance, but systematic
errors in the temperature measurement can arise from a
number of sources, and the ADT7466 can reduce these errors.
As CPUs run faster, it is more difficult to avoid high frequency
clocks when routing the D+, D− tracks around a system board.
Even when recommended layout guidelines are followed, there
may still be temperature errors attributed to noise being
coupled onto the D+/D− lines. High frequency noise generally
has the effect of giving temperature measurements that are too
high by a constant amount. The ADT7466 has temperature
offset registers at addresses 0x26 and 0x27 for the remote and
local temperature channels. A one time calibration of the
system can determine the offset caused by system board noise
and null it out using the offset registers. The offset registers
automatically add a twos complement 8-bit reading to every
temperature measurement. The LSB adds 1°C offset to the
temperature reading so the 8-bit register effectively allows
temperature offsets of up to 128°C with a resolution of 1°C.
This ensures that the readings in the temperature measurement
registers are as accurate as possible.
The ADT7466 can also be operated by using an extended
temperature range from −64°C to +191°C. In this case, the
whole range of the ADC is used, but the ADC code is offset by
+64°C, so it does not correspond directly to the temperature.
(0°C = 0100000) .
The user can switch between these two temperature ranges by
setting or clearing Bit 7 in Configuration Register 1. The
measurement range should be switched only once after power-
up, and the user should wait for two monitoring cycles
(approximately 68 ms) before expecting a valid result. Both
ranges have different data formats, as shown in Table 11.
Table 11. Temperature Data Format
Table 12. Temperature Offset Registers
Temperature
−64°C
0°C
Binary1
Offset Binary2
0 000 0000
0 100 0000
0 100 0001
0 100 1010
0 101 1001
0 111 0010
1 000 1011
1 010 0100
1 011 1101
1 011 1111
1 111 1111
Register
Description
Default
0 000 0000
0 000 0000
0 000 0001
0 000 1010
0 001 1001
0 011 0010
0 100 1011
0 110 0100
0 111 1101
0 111 1111
0 111 1111
0x24
0x25
Thermistor 1/Remote 2 offset
Thermistor 2 offset
0x00 (0°C)
0x00 (0°C)
0x00 (0°C)
0x00 (0°C)
1°C
10°C
25°C
50°C
0x26
0x27
Remote1 temperature offset
Local temperature offset
Table 13. Temperature Measurement Registers
75°C
Register
Description
Default
0x00
0x00
100°C
125°C
127°C
191°C
0x0D
0x0E
Remote temperature
Local temperature
0x08
Extended Resolution 1
Bits 1:0 remote temperature LSBs
Extended Resolution 2
Bits 1:0 local temperature LSBs
0x00
1 Binary scale temperature measurement returns 0 for all temperatures ≤0°C.
2 Offset binary scale temperature values are offset by +64.
0x09
0x00
While the temperature measurement range can be set to −64°C
to +191°C for both local and remote temperature monitoring,
the ADT7466 itself should not be exposed to temperatures
greater than those specified in the Absolute Maximum Ratings
table. Furthermore, the device is guaranteed to only operate at
ambient temperatures from −40°C to +125°C. In practice, the
device itself should not be exposed to extreme temperatures,
and may need to be shielded in extreme environments to
comply with these requirements. Only the remote temperature
monitoring diode should be exposed to temperatures above
+120°C and below −40°C. Care should be taken in choosing a
remote temperature diode to ensure that it can function over
the required temperature range.
Associated with each temperature measurement channel are
high and low limit registers. Exceeding the programmed high or
low limit causes the appropriate status bit to be set. Exceeding
either limit can also generate
interrupts.
ALERT
Table 14. Temperature Measurement Limit Registers
Register
0x1A
0x1B
0x1C
0x1D
0x14
0x15
0x16
0x17
Description
Default
0x00
0x7F
0x00
0x7F
0x00
0xFF
0x00
0xFF
Remote1 temperature low limit
Remote1 temperature high limit
Local temperature low limit
Local temperature high limit
Thermistor 1/Remote 2 low limit
Thermistor 1/Remote 2 high limit
Thermistor 2 low limit
Thermistor 2 high limit
Rev. 0 | Page 18 of 48
ADT7466
All temperature limits must be programmed in the same format
as the temperature measurement. If this is offset binary, add 64
(0x40 or 01000000) to the actual temperature limit in degrees
Celsius.
two thermocouples with a big temperature differential between
them, thermocouple voltages should be much less than 200 mV.
Place a 0.1 µF bypass capacitor close to the ADT7466.
Layout Considerations
TEMPERATURE MEASUREMENT USING
THERMISTORS
Digital boards can be electrically noisy environments. Take the
following precautions to protect the analog inputs from noise,
particularly when measuring the very small voltages from a
remote diode sensor.
The analog input channels, AIN1 and AIN2, can be used to
measure temperature by using negative temperature coefficient
(NTC) thermistors. NTC thermistors have a nonlinear transfer
function of the form
Place the ADT7466 as close as possible to the remote sensing
diode. Provided that the worst noise sources, such as clock
generators, data/address buses and CRTs, are avoided, this
distance can be 4 inches to 8 inches.
⎛
⎜
⎜
⎝
⎞
⎟
⎟
⎠
B
B
Rt2 = Rt1 ×e
−
t2 t1
where:
If the distance to the remote sensor is more than 8 inches, the
use of twisted-pair cable is recommended. This works from
about 6 feet to 12 feet.
Rt2 is the resistance at temperature t2.
Rt1 is the resistance at temperature t1 (usually 25°C).
e = 2.71828.
B is the B constant of the thermistor (typically between 3000
and 5000).
For very long distances (up to 100 feet), use shielded twisted
pair, such as Belden #8451 microphone cable. Connect the
twisted pair to D+ and D− and the shield to GND close to the
ADT7466. Leave the remote end of the shield unconnected to
avoid ground loops.
A thermistor can be made to give a voltage output that is fairly
linear over a limited range by making it part of a potential
divider as shown in Figure 26.
Because the measurement technique uses switched current
sources, excessive cable and/or filter capacitance can affect the
measurement. When using long cables, the filter capacitor could
be reduced or removed.
A potential divider, with a thermistor as the upper part
connected to REFOUT, produces an output voltage that varies
nonlinearly in proportion to the inverse of the resistance. By
suitable choice of thermistor and fixed resistor, this can be made
to approximately cancel the nonlinearity of the thermistor
resistance vs. temperature curve, thus giving a fairly linear
output voltage with temperature over a limited range. This
circuit uses REFOUT as the excitation voltage for both the
thermistor and for the ADC, so any variation in REFOUT is
cancelled, and the measurement is purely ratiometric.
Route the D+ and D− tracks close together, in parallel, with
grounded guard tracks on each side. Provide a ground plane
under the tracks if possible.
Use wide tracks to minimize inductance and reduce noise
pickup. A 5 mil track minimum width and spacing is
recommended.
ADT7466
5MIL
5MIL
5MIL
5MIL
5MIL
5MIL
5MIL
GND
REFOUT
TH2
TH1
TH1
TH2
D+
R
2
R
1
EXT
EXT
D–
Figure 26. Temperature Measurement Using Thermistor
GND
Figure 25. Arrangement of Signal Tracks
Try to minimize the number of copper/solder joints, which can
cause thermocouple effects. Where copper/solder joints are
used, make sure that they are in both the D+ and D− paths and
are at the same temperature.
Thermocouple effects should not be a major problem because
1°C corresponds to about 240 µV, and thermocouple voltages
are about 3 µV/°C of temperature difference. Unless there are
Rev. 0 | Page 19 of 48
ADT7466
Thermistor Linearization
Thermistor Normalization
A linear transfer function can be obtained over a limited
temperature range by connecting the thermistor in series with
an optimum resistor. Placing a resistor in series with the
thermistor as shown in Figure 26 produces an S-shaped error
curve as shown in Figure 27. The overall error across the range
can be reduced by calculating the external resistor so that the
error is 0 at the ends of the range. REXT is calculated as follows:
Even when the thermistor is linearized, it does not provide an
output to the ADC that gives a direct temperature reading in
degrees Celsius. The linearized data is proportional to the
voltage applied; however, normalization is needed to use the
value as a temperature reading.
To overcome this problem, when an analog input is configured
for use with a thermistor, the output of the ADC is scaled and
offset so that it produces the same output (for example, 1 LSB =
0.25°C) as from the thermal diode input, when REXT is chosen to
linearize the thermistor over 30°C to 100°C.
RMID × (RMIN + RMAX ) − (2 × RMIN × RMAX
)
REXT
where:
=
(RMIN + RMAX − 2 × RMID
)
Normalization can be chosen for 10 kΩ thermistors by setting
Bit 0 of Configuration Register 2 (0x01) or for 100 kΩ
thermistors by clearing this bit (default setting).
R
R
R
MIN is the thermistor value at TMIN
.
MAX is the thermistor value at TMAX
.
TMIN +TMAX
MID is the thermistor value at
2
READING TEMPERATURE FROM THE ADT7466
Figure 27 shows the linearity error using a 100 kΩ thermistor
with a B value of 3500 and a 14400 Ω resistor. Using the
specified thermistor and resistor, the error over a temperature
range of 30°C to 100°C is less than 2°C. Other thermistors can
be used, but the resistor value is different. A smaller error can
be achieved over a narrower temperature range; conversely, a
wider temperature range can be used, but the error is greater. In
both cases, the optimum resistor value is different.
It is important to note that temperature can be read from the
ADT7466 as an 8-bit value (with 1°C resolution) or as a 10-bit
value (with 0.25°C resolution). If only 1°C resolution is
required, the temperature readings can be read at any time
and in no particular order.
If the 10-bit measurement is required, this involves a 2-register
read for each measurement. The extended resolution registers
(0x08 and 0x09) should be read first. This causes all temperature
reading registers to be frozen until all temperature reading
registers have been read. This prevents an MSB reading from
being updated while its 2 LSBs are being read and vice versa.
2
1
Measurement Sequence
The ADT7466 automatically measures each analog and
temperature channel in the following round-robin sequence:
0
1. AIN1/TH1
–1
2. AIN2(TH2)
3. VCC
–2
30
4. Remote Temperature 1 (D1)
5. Local Temperature
40
50
60
70
80
90
100
TEMPERATURE (°C)
Figure 27. Linearity Error Using Specified Components
If AIN1 and AIN2 are configured for a second thermal diode,
this is measured instead of the AIN1 and AIN 2 measurements,
and the result stored in the AIN1 reading register (0x0A).
Rev. 0 | Page 20 of 48
ADT7466
Analog Monitoring Cycle Time
Single-Channel ADC Conversions
The analog monitoring cycle begins when a 1 is written to the
start bit (Bit 0) of Configuration Register 1 (0x00). The ADC
measures each analog input in turn, and, as each measurement
is completed, the result is automatically stored in the appropriate
value register. This round-robin monitoring cycle continues
until disabled by writing a 0 to Bit 0 of Configuration Register 1.
Setting Bit 3 of Configuration Register 4 (Address 0x03) places
the ADT7466 into single-channel ADC conversion mode. In
this mode, the ADT7466 can be made to read a single
temperature channel only. The selected input is read every
1.4 ms. The appropriate ADC channel is selected by writing to
Bits 2:0 of Configuration Register 4 (Address 0x03).
Table 16. ADC Single-Channel Selection
Since the ADC is normally left to free-run in this manner, the
time to monitor all the analog inputs is normally not of interest,
because the most recently measured value of any input can be
read at any time.
Bits 2:0, Reg. 0x03
Channel Selected
AIN1/ Thermistor1
AIN2/ Thermistor2
VCC
000
001
010
011
100
101
For applications where the monitoring cycle time is important,
it can easily be calculated from the measurement times of the
individual channels. With averaging turned on, each
Remote 1 temperature
Local temperature
Remote 2 temperature
measurement is taken 16 times and the averaged result is placed
in the value register. The worst-case monitoring cycle times for
averaging turned on and off is described in Table 15.
LIMIT VALUES
High and low limits are associated with each measurement
channel on the ADT7466. These limits can form the basis of
system status monitoring; a status bit can be set for any out-of-
limit condition and detected by polling the device. Alternatively,
Fan tach measurements are made in parallel but independently
and are not synchronized with the analog measurements.
Table 15. Monitoring Cycle Time
interrupts can be generated to flag out-of-limit
ALERT
Monitoring Cycle Time
conditions for a processor or microcontroller.
Channel
Avg On
8.99 ms
36.69 ms
36.69 ms
8.65 ms
8.65 ms
8.26ms
Avg Off
1.36 ms
6.25 ms
6.25 ms
1.02 ms
1.02 ms
0.61ms
Local temperature
Remote 1 temperature
Remote 2 temperature
AIN1/Thermistor 1
AIN2/Thermistor 2
VCC
Voltage and temperature limits are only 8-bit values and are
compared with the 8 MSBs of the voltage and temperature
values.
8-Bit Limits
The following tables list the 8-bit limits on the voltage limit and
temperature limit registers of the ADT7466.
Total1
Total2
71.24 ms
90.63 ms
10.26ms
14.47 ms
Table 17. Voltage Limit Registers
1 Pin 11 and Pin 12 configured for AIN/thermistor monitoring. The total
excludes the Remote 2 temperature time.
Register
Description
Default
0x00
0xFF
0x00
0xFF
2 Pin 11 and Pin 12 configured for second thermal diode monitoring. The total
excludes the AIN1/Thermistor 1 and AIN2/Thermistor 2 times.
0x14
0x15
0x16
0x17
AIN1 low limit
AIN1 high limit
AIN2 low limit
AIN2 high limit
VCC low limit
ADDITIONAL ADC FUNCTIONS
A number of other functions are available on the ADT7466 to
offer the systems designer increased flexibility.
0x18
0x00
0xFF
0x19
VCC high limit
Turn Off Averaging
Table 18. Temperature Limit Registers
For each temperature measurement read from a value register,
16 readings have actually been made internally and the results
averaged before being placed into the value register. The user
may want to take a very fast measurement, for example, of CPU
temperature. Setting Bit 4 of Configuration Register 2 (0x01)
turns averaging off.
Register
0x1A
0x1B
0x1C
0x1D
0x1E
Description
Default
0x00
0x7F
0x00
0x7F
0x00
0x64
0x64
0x64
0x64
Remote temperature low limit
Remote temperature high limit
Local temperature low limit
Local temperature high limit
PROCHOT limit
0x1F
AIN1(TH1)/REM2 THERM limit
AIN2(TH2) THERM limit
Remote THERM limit
0x20
0x21
0x22
Local THERM limit
Rev. 0 | Page 21 of 48
ADT7466
16-Bit Limits
Interrupt status mask registers (0x12, 0x13) allow individual
interrupt sources to be masked from causing an
However, if one of these masked interrupt sources goes out-of-
limit, its associated status bit is set in the interrupt status
registers.
The fan tach measurements are 16-bit results. The fan tach
limits are also 16 bits, consisting of a high byte and low byte.
Since fans running under speed or stalled are normally the only
conditions of interest, only high limits exist for fan tachs. Since
the fan tach period is actually being measured, exceeding the
limit indicates a slow or stalled fan.
.
ALERT
Table 20. Interrupt Status Register 1 (Reg. 0x10)
Bit No. Name Description
Table 19. Fan Limit Registers
Register
7
OOL
1 indicates that a bit in Status Register 2 is set
and that Status Register 2 should be read.
Description
Default
0xFF
0xFF
0xFF
0xFF
0x4C
0x4D
0x4E
0x4F
TACH1 minimum low byte
TACH1 minimum high byte
TACH2 minimum low byte
TACH2 minimum high byte
6
5
4
3
AIN1
AIN2
VCC
1 indicates that AIN1 is out of limit.
1 indicates that AIN2 is out of limit.
1 indicates that VCC is out of limit.
1 indicates that the remote temperature
measurement is out of limit.
REM
2
1
0
LOC
1 indicates that the local temperature
measurement is out of limit.
1 indicates that the Tach 1 count is above
limit (fan speed below limit).
1 indicates that the Tach 2 count is above
limit (fan speed below limit).
Out-of-Limit Comparisons
Once all limits have been programmed, ADT7466 monitoring
can be enabled. The ADT7466 measures all parameters in round-
robin format and sets the appropriate status bit for out-of-limit
conditions. Comparisons are done differently depending on
whether the measured value is being compared to a high or low
limit.
FAN1
FAN2
Table 21. Interrupt Status Register 2 (Reg. 0x11)
Bit No. Name Description
5
4
3
A greater than comparison is performed when comparing with
the high limit.
THRM2 1 indicates that TH1 is open-circuit.
THRM1 1 indicates that TH2 is open-circuit.
D2
A less than or equal to comparison is performed when comparing
with the low limit.
1 indicates that Remote Temperature
Sensing Diode 2 is open-circuit or short-
circuit.
1 indicates that Remote Temperature
Sensing Diode 1 is open-circuit or short-
circuit.
1 indicates that the PROCHOT limit has been
exceeded.
1 indicates that a THERM overtemperature
limit has been exceeded.
Status Registers
2
D1
The results of limit comparisons are stored in Status Register 1
and Status Register 2. The status register bit for each channel
reflects the status of the last measurement and limit comparison
on that channel. If a measurement is within limits, the corre-
sponding status register bit is cleared to 0. If the measurement is
out-of-limits the corresponding status register bit is set to 1.
1
0
PHOT
OVT
The state of the various measurement channels can be polled by
reading the status registers over the serial bus. When Bit 7
(OOL) of Status Register 1 (0x10) is 1, an out-of-limit event has
been flagged in Status Register 2. Therefore the user need only
read Status Register 2 when this bit is set. Alternatively, the
output (Pin 14) can be used as an interrupt, which
ALERT
automatically notifies the system supervisor of an out-of-limit
condition. Reading the status registers clears the appropriate
status bit as long as the error condition that caused the interrupt
has cleared. Status register bits are sticky, meaning that they
remain set until read by software. Whenever a status bit is set,
indicating an out-of-limit condition, it remains set even if the
event that caused it cleared (until read). The only way to clear
the status bit is to read the status register when the event clears.
Rev. 0 | Page 22 of 48
ADT7466
ALERT INTERRUPT BEHAVIOR
HIGH LIMIT
The ADT7466 can be polled for status, or an
interrupt
ALERT
can be generated for out-of-limit conditions. It is important to
note how the output and status bits behave when
writing interrupt handler software.
TEMPERATURE
ALERT
CLEARED ON READ
(TEMP BELOW LIMIT)
STICKY
STATUS
BIT
HIGH LIMIT
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
ALERT
TEMPERATURE
INTERRUPT
MASK BIT SET
INTERRUPT MASK BIT
CLEARED
CLEARED ON READ
(TEMP BELOW LIMIT)
(ALERT REARMED)
STICKY
STATUS
BIT
ALERT
Figure 29. How Masking the Interrupt Source Affects
Output
TEMP BACK IN LIMIT
(STATUS BIT STAYS SET)
Masking Interrupt Sources
ALERT
Interrupt Mask Registers 1 and 2 are located at Addresses 0x12
and 0x13. These registers allow individual interrupt sources to
ALERT
Figure 28.
and Status Bit Behavior
be masked to prevent
source prevents only the
the appropriate status bit is set as normal.
interrupts. Masking an interrupt
ALERT
Figure 28 shows how the
output and sticky status bits
ALERT
output from being asserted;
ALERT
behave. Once a limit is exceeded, the corresponding status bit is
set to 1. The status bit remains set until the error condition
subsides and the status register is read. This ensures that an out-
of-limit event cannot be missed if software is polling the device
Table 22. Interrupt Mask Register 1 (Reg. 0x12)
Bit No. Name
Description
periodically. The
output remains low while a reading is
ALERT
7
6
OOL
1 masks ALERT for any alert condition
flagged in Status Register 2.
1 masks ALERT for AIN1(TH1)/REM2.
out-of-limit, until the status register is read. This has implica-
tions on how software handles the interrupt.
AIN1(TH1)/
REM2
Handling Alert Interrupts
5
4
3
AIN2(TH2)
VCC
1 masks ALERT for AIN2(TH2).
1 masks ALERT for Vcc.
To prevent the system from being tied up servicing interrupts, it
is recommended to handle the
interrupt as follows:
ALERT
REM1
1 masks ALERT for remote
temperature.
1 masks ALERT for local temperature.
1. Detect the
assertion.
ALERT
2
1
0
LOC
FAN1
FAN2
1 masks ALERT for Fan 1.
1 masks ALERT for Fan 2.
2. Enter the interrupt handler.
3. Read the status registers to identify the interrupt source.
Table 23. Interrupt Mask Register 2 (Reg. 0x13)
Bit No. Name Description
4. Mask the interrupt source by setting the appropriate mask
bit in the interrupt mask registers (0x12, 0x13).
5
THRM2 1 masks ALERT for TH1 open- or short-circuit
errors.
5. Take the appropriate action for a given interrupt source.
6. Exit the interrupt handler.
4
3
THRM1 1 masks TH2 open- or short-circuit errors.
D1
1 masks ALERT for Diode 1 open- or short-
circuit errors.
7. Periodically poll the status registers. If the interrupt status
bit has cleared, reset the corresponding interrupt mask bit
2
D2
1 masks ALERT for Diode 2 open- or short-
circuit errors.
to 0. This causes the
output and status bits to
ALERT
1
0
PHOT 1 masks ALERT for PROCHOT.
behave as shown in Figure 29.
OVT
1 masks ALERT for over temperature
(exceeding THERM limits).
Rev. 0 | Page 23 of 48
ADT7466
Measuring
Assertion Time
PROCHOT
time, Bit 1 of the
timer is set, and Bit 0 is cleared.
PROCHOT
Bit 0 now reflects timer readings with a resolution of 25 ms.
When using the timer, be aware of the following.
The ADT7466 has an internal timer to measure
PROCHOT
assertion time. The timer is started on the assertion of the
ADT7466 input, and stopped on the negation of
PROCHOT
timer read (0x0F):
PROCHOT
the pin. The timer counts
After a
PROCHOT
times cumulatively, that
PROCHOT
•
•
The contents of the timer are cleared on read.
is, the timer resumes counting on the next
assertion. The
PROCHOT
PROCHOT
timer continues to accumulate
PROCHOT
The PHOT bit (Bit 1) of Status Register 2 is cleared
automatically.
assertion times until the timer is read (it is cleared
on read) or until it reaches full scale. If the counter reaches full
scale, it stops at that reading until it is cleared.
If the
timer is read during a
assertion,
PROCHOT
PROCHOT
the following happens:
The 8-bit
that Bit 0 is set to 1 on the first
cumulative
timer register (0x0F) is designed such
PROCHOT
•
•
The contents of the timer are cleared.
assertion. Once the
PROCHOT
Bit 0 of the
PROCHOT
timer is set to 1 (since a
assertion is occurring).
PROCHOT
assertion time exceeds 50 ms, Bit 1 of
PROCHOT
timer is set, and Bit 0 becomes the LSB of the
the
PROCHOT
•
•
The
timer increments from 0.
PROCHOT
timer with a resolution of 22.76 ms.
If the
limit (0x1E) = 0x00, the PHOT bit is set.
PROCHOT
PROCHOT
Generating
Interrupts from
Events
ALERT
PROCHOT
0 0 0 0 0 0 0 1
PROCHOT
The ADT7466 can generate
s when a programmable
ALERT
limit is exceeded. This allows the systems designer
TIMER
7 6 5 4 3 2 1 0 PROCHOT ASSERTED < OR = 25ms
(REG. 0x0F)
PROCHOT
to ignore brief, infrequent
assertions, while
events that could signify a more
PROCHOT
PROCHOT
capturing longer
PROCHOT
serious thermal problem within the system. Register 0x1E is the
limit register. This 8-bit register allows a limit from
ACCUMULATE PROCHOT LOW
PROCHOT
0 seconds (first
ASSERTION TIMES
assertion) to 6.4 seconds to be set
PROCHOT
0 0 0 0 0 0 1 0
7 6 5 4 3 2 1 0
PROCHOT
TIMER
(REG. 0x0F)
PROCHOT ASSERTED > OR = 50ms
before an
is generated. The
timer value is
limit register. If
ALERT
compared with the contents of the
the
PROCHOT
PROCHOT
timer value exceeds the
limit value,
PROCHOT
PROCHOT
PROCHOT
the PHOT bit (Bit 1) of Status Register 2 is set, and an
is
ALERT
generated. The PHOT bit (Bit 1) of Mask Register 2 (0x13)
masks s if this bit is set to 1, although the PHOT bit of
ACCUMULATE PROCHOT LOW
ASSERTION TIMES
ALERT
0 0 0 0 0 1 0 1
PROCHOT
Interrupt Status Register 2 is still set if the
exceeded.
limit is
PROCHOT
PROCHOT ASSERTED > OR = 125ms
(100ms + 25ms)
TIMER
7 6 5 4 3 2 1 0
(REG. 0x0F)
PROCHOT
Figure 30.
Timer
Figure 32 is a functional block diagram of the
timer
PROCHOT
limit and associated circuitry. Writing a value of 0x00 to the
Figure 30 shows how the
timer behaves as the
PROCHOT
limit register (0x21) causes
to be generated
limit value of
PROCHOT
on the first
ALERT
input is asserted and negated. Bit 0 is set on the first
assertion that is detected. This bit remains set until
PROCHOT
PROCHOT
assertion. A
PROCHOT
PROCHOT
0x01 generates an
when cumulative
PROCHOT
ALERT
the cumulative
assertions exceed 50 ms. At this
PROCHOT
assertions exceed 50 ms.
Rev. 0 | Page 24 of 48
ADT7466
Figure 32 shows how the
in the event of a critical overtemperature.
pin asserts low as an output
THERM
CONFIGURING THE ADT7466 THERM PIN
AS AN OUTPUT
PROCHOT
If
monitoring is not required, Pin 7 can be config-
output by setting Bits 1:0 of Configuration
THERM LIMIT
THERM
ured as a
25°C
THERM LIMIT
Register 3 to 01. The user can preprogram system critical thermal
limits. If the temperature exceeds a thermal limit by 0.25°C,
TEMP
THERM
asserts low. If the temperature is still above the thermal
THERM
THERM
stays low.
limit on the next monitoring cycle,
THERM
remains asserted low until the temperature is equal to or below
the thermal limit. Since the temperature for that channel is
THERM
measured only every monitoring cycle, once
asserts, it
ADT7466
MONITORING
CYCLE
is guaranteed to remain low for at least one monitoring cycle.
THERM
The
TH2, external or internal temperature
THERM
pin can be configured to assert low if the TH1,
THERM
THERM
Limits
Figure 31. Asserting
as an Output Based on Tripping
THERM
limits are
limit registers are at locations
0x1F, 0x20, 0x21, and 0x22, respectively.
exceeded by 0.25°C. The
3.2s
1.6s
800ms
3.2s
1.6s
800ms
PROCHOT LIMIT 400ms
400ms PROCHOT TIMER
(REG. 0x1E)
(REG. 0x0F)
200ms
100ms
50ms
200ms
100ms
50ms
25ms
25ms
0 1 2 3 4 5 6 7
7 6 5 4 3 2 1 0
PROCHOT
PROCHOT TIMER CLEARED
ON READ
COMPARATOR
PCHT BIT (BIT 1)
IN OUT
LATCH
RESET
STATUS
REGISTER 2
SMBALERT
1 = MASK
CLEARED ON
READ
PHOT BIT 1
MASK REGISTER 2
(REG. 0x13)
PROCHOT
Figure 32. Functional Diagram of the ADT7466
Monitoring Circuitry
Rev. 0 | Page 25 of 48
ADT7466
PWM OR SWITCH MODE FAN DRIVE
FAN DRIVE
Linear dc speed controllers, such as the ones described
previously, waste power, which is dissipated as heat in the power
transistor. To save power and reduce heat dissipation, it may be
desirable to control the fan speed with a more efficient dc-dc
converter or a pulse width modulated (PWM) speed controller.
In this case, the DRIVE outputs of the ADT7466 provide the
reference voltage for this circuit. To maximize efficiency, the
controller can be switched off completely whenever the Fan 1
drive value falls below the value in the V_FAN_MIN register.
When this happens, the FAN1_ON output goes low.
The ADT7466 contains two DACs to control fan speed. The
full-scale output of these DACs is typically 2.2 V @ 2 mA, so
they must be buffered in order to drive 5 V or 12 V fans. The
output voltage of these DACs is controlled by data written to the
DRIVE1 (0x40) and DRIVE2 (0x41) registers.
Since fans do not turn on below a certain drive voltage, a
significant proportion of the DAC range would be unusable;
however, four other registers associated with fan speed control
help the user to avoid this problem.
Fan start-up voltage registers (0x30 and 0x31) determine the
voltage initially applied to the fans at startup. This should be
high enough to ensure that the fans start.
V+
ADT7466
DRIVE
VOLTAGE
DRIVE1
DC-DC
OR PWM
Minimum speed registers (0x32 and 0x33) determine the
minimum voltage that is applied to the fans. This should be
high enough to keep the fans turning and less than the voltage
required to start them.
FAN SPEED
SHUTDOWN
CONTROLLER
FAN1 ON
The speed registers associated with automatic fan speed control
(AFC) are the maximum speed registers (0x34 and 0x35). They
allow the maximum output from the DACs to be limited to less
than the full-scale output.
Figure 35. DC-DC or PWM Fan Speed Control
FAN SPEED MEASUREMENT
Some suitable fan drive circuits are shown in Figure 33 and
Figure 34. Basically, voltage amplification is required to boost
the full-scale output of the DAC to 5 V or 12 V, and the
amplifier needs sufficient drive current to meet the drive
requirements of the fan.
TACH Inputs
Pin 2 and Pin 4 are tach inputs intended for fan speed
measurement. The ADT7466 can measure the speed of 3-wire
fans. Each 3-wire fan has two supply wires and a tach output
wire.
Note that as the external transistor increases the open-loop gain
of the op amp, it may be necessary to add a capacitor around
the feedback loop to maintain stability.
Signal conditioning in the ADT7466 accommodates the slow
rise and fall times typical of fan tachometer outputs. The
maximum input signal range is 0 V to 6.5 V, even when VCC is
less than 5 V. If these inputs are supplied from fan outputs that
exceed 0 V to 6.5 V, either resistive attenuation of the fan signal
or diode clamping must be included to keep inputs within an
acceptable range.
12V
1/4
LM324
R3
1kΩ
AOUT
Q1
2N2219A
Monitoring 3-Wire Fans
R2
12kΩ (5V)
Figure 36 to Figure 39 show circuits for most common 3-wire
fan tach outputs.
R1
10kΩ
43kΩ (12V)
If the fan tach output has a resistive pull-up to VCC, it can be
connected directly to the fan input, as shown in Figure 36.
Figure 33. Fan Drive Circuit with Op Amp and Emitter-Follower
5V OR 12V
V
CC
FAN DRIVE
1/4
LM324
R3
100kΩ
DAC
Q1
IRF9620
ADT7466
PULLUP
4.7kΩ
TYP.
TACH
FAN SPEED
COUNTER
R2
12kΩ (5V)
R1
10kΩ
TACH
OUTPUT
43kΩ (12V)
Figure 36. Fan with Tach Pull-Up to +VCC
Figure 34. Fan Drive Circuit with P-Channel MOSFET
Rev. 0 | Page 26 of 48
ADT7466
If the fan output has a resistive pull-up to 12 V (or other voltage
greater than 6.5 V), the fan output can be clamped with a Zener
diode, as shown in Figure 37. The Zener diode voltage should
be greater than VIH of the tach input but less than 6.5 V,
allowing for the voltage tolerance of the Zener. A value of
between 3 V and 5 V is suitable.
Fan Speed Registers
The fan counter does not count the fan tach output pulses
directly because the fan speed can be less than 1000 rpm; it
would take several seconds to accumulate a reasonably large
and accurate count. Instead, the period of the fan revolution is
measured by gating an on-chip 82 kHz oscillator into the input
of a 16-bit counter for N periods of the fan tach output, as
shown in Figure 40. The accumulated count is actually
proportional to the fan tachometer period and inversely
proportional to the fan speed.
V
CC
FAN DRIVE
ADT7466
PULL-UP
4.7kΩ
TACH
TYP.
OUTPUT TACH
FAN SPEED
COUNTER
CLOCK
ZD1*
ZENER
TACH
*CHOOSE ZD1 VOLTAGE APPROX. 0.8
× V
CC
1
2
Figure 37. Fan with Tach.
Pull-Up to Voltage >6.5 V, for Example, 12 V Clamped with Zener Diode.
Figure 40. Fan Speed Measurement
If the fan has a strong pull-up (less than 1 kΩ) to 12 V, or a
totem pole output, a series resistor can be added to limit the
Zener current, as shown in Figure 38. Alternatively, a resistive
attenuator can be used, as shown in Figure 39.
N, the number of pulses counted, is determined by the settings
of Register 0x39 (fan pulses per revolution register). This
register contains 2 bits for each fan, allowing 1, 2 (default), 3 or
4 tach pulses to be counted.
R1 and R2 should be chosen such that
The fan tachometer readings are 16-bit values consisting of a
2-byte read from the ADT7466.
2 V < VPULLUP × R2/(RPULLUP + R1 + R2) < 5 V
The fan inputs have an input resistance of nominally 160 kΩ to
ground, which should be taken into account when calculating
resistor values.
Table 24. Fan Speed Measurement Registers
Register
Description
Default
0xFF
0xFF
0xFF
0xFF
0x48
0x49
0x4A
0x4B
TACH1 low byte
TACH1 high byte
TACH2 low byte
TACH2 high byte
With a pull-up voltage of 12 V and pull-up resistor less than
1 kΩ, suitable values for R1 and R2 are 100 kΩ and 47 kΩ. This
gives a high input voltage of 3.83 V.
V
CC
FAN DRIVE
Reading Fan Speed from the ADT7466
ADT7466
Measuring fan speeds involves a 2-register read for each
measurement. The low byte should be read first, which causes
the high byte to be frozen until both high and low byte registers
are read. This prevents erroneous tach readings.
TACH
OUTPUT TACH
FAN SPEED
COUNTER
R1
PULL-UP
ZD1*
10kΩ
ZENER
TYP. < 1kΩ
OR TOTEM POLE
The fan tachometer reading registers report the number of
12.2 µs period clocks (82 kHz oscillator) gated to the fan speed
counter from the rising edge of the first fan tach pulse to the
rising edge of the third fan tach pulse, assuming two pulses per
revolution is being counted. Since the device is essentially
measuring the fan tach period, the higher the count value, the
slower the fan is actually running. A 16-bit fan tachometer
reading of 0xFFFF indicates either that the fan has stalled or
that it is running very slowly (<75 rpm).
*CHOOSE ZD1 VOLTAGE APPROX. 0.8
× V
CC
Figure 38. Fan with Strong Tach.
Pull-Up to >VCC or Totem Pole Output, Clamped with Zener and Resistor.
V
CC
FAN DRIVE
ADT7466
TACH
<1kΩ
OUTPUT
TACH
R2*
FAN SPEED
COUNTER
R1*
A greater than comparison is performed when comparing with
the high limit.
*SEE TEXT
The actual fan tach period is being measured in this case.
Therefore, when the fan tach limit is exceeded, a 1 is set for the
Figure 39. Fan with Strong Tach.
Pull-Up to >VCC or Totem Pole Output, Attenuated with R1/R2.
appropriate status bit and can be used to generate an
.
ALERT
Rev. 0 | Page 27 of 48
ADT7466
The fan tach limit registers are 16-bit values consisting of 2 bytes.
Table 26. Fan Pulses Per Revolution Register
Fan
Default
Table 25. Fan Tach Limit Registers
1:0 FAN1
3:2 FAN2
2 pulses per revolution
2 pulses per revolution
Register
Description
Default
0xFF
0xFF
0xFF
0xFF
0x4C
0x4D
0x4E
0x4F
TACH1 minimum low byte
TACH1 minimum high byte
TACH2 minimum low byte
TACH2 minimum high byte
Table 27. Fan Pulses Per Revolution Values
Code
Pulses per Revolution
00
01
10
11
1
2
3
4
Fan Speed Measurement Rate
The fan tach readings are normally updated once every second.
The FAST bit (Bit 3) of Configuration Register 3 (0x02) updates
the fan tach readings every 250 ms, when set to 1. If any of the
fans are not being driven by a fan drive output, but are powered
directly from 5 V or 12 V, its associated dc bit in Configuration
Register 3 should be set. This allows tach readings to be taken
on a continuous basis for fans connected directly to a dc source.
The ADT7466 has a unique fan spin-up function. It spins the
fan with the fan start-up voltage until two tach pulses are
detected on the tach input. Once two pulses are detected, the
fan drive goes to the expected running value. The advantage of
this is that fans have different spin-up characteristics and take
different times to overcome inertia. The ADT7466 runs the fans
just fast enough to overcome inertia and is quieter on spin-up
than fans programmed to spin-up for a given spin-up time.
Calculating Fan Speed
Assuming a fan with two pulses/revolution (and two
pulses/revolution being measured) fan speed is calculated by
FAN START-UP TIMEOUT
Fan Speed (rpm) = (82000 × 60)/Fan Tach Reading
where Fan Tach Reading is the 16-bit fan tachometer reading.
For example, if
To prevent false interrupts being generated as a fan spins up
(since it is below running speed), the ADT7466 includes a fan
start-up timeout function. This is the time limit allowed for two
tach pulses to be detected on spin-up. For example, if a
2-second fan start-up timeout is chosen, and no tach pulses
occur within two seconds of the start of spin-up, a fan fault is
detected and flagged in Interrupt Status Register 1.
TACH1 High Byte (Reg. 0x49) = 0x17
TACH1 Low Byte (Reg. 0x48) = 0xFF
then fan speed in rpm is
Start-Up Timeout Configuration (Reg. 0x38)
Bits 2:0 control the start-up timeout for DRIVE1. Bits 5:3
control the start-up timeout for DRIVE2.
Fan 1 TACH reading = 0x17FF = 6143 decimal
rpm = (82000 × 60)/Fan 1 TACH reading
rpm = (82000 × 60)/6143 = 800 = fan speed
Table 28. Start-Up Timeout Configuration
Code
000
001
010
011
100
101
110
111
Timeout
No start-up timeout
100 ms
250 ms
400 ms
Fan Pulses Per Revolution
Different fan models can output either 1, 2, 3, or 4 tach pulses
per revolution. Once the number of fan tach pulses is
determined, it can be programmed into the fan pulses per
revolution register (0x39) for each fan. Alternatively, this
register can be used to determine the number of
pulses/revolution output by a given fan. By plotting fan speed
measurements at 100% speed with different pulses/revolution
settings, the smoothest graph with the lowest ripple determines
the correct pulses/revolution value.
667 ms
1 second
2 seconds
4 seconds
Rev. 0 | Page 28 of 48
ADT7466
Fan Start Voltage (V_FAN_ON)
AUTOMATIC FAN SPEED CONTROL
This is the minimum drive voltage from the DAC at which a fan
starts running. This depends on the parameters of the fan and
the characteristics of the fan drive circuit.
The ADT7466 has a local temperature sensor and a remote
temperature channel, which can be connected to an on-chip
diode-connected transistor on a CPU. In addition, the two
analog input channels can be reconfigured for temperature
measurement. Any or all of these temperature channels can be
used as the basis for automatic fan speed control to drive fans
according to system temperature. By running the fans at only
the speed needed to maintain a desired temperature, acoustic
noise is reduced. Reducing fan speed can also decrease system
current consumption.
Minimum Fan Speed (V_FAN_MIN)
This is the minimum drive voltage from the DAC at which a fan
keeps running, which is lower than the voltage required to start
it. This depends on the parameters of the fan and the
characteristics of the fan drive circuit.
Maximum Fan Speed
For acoustic reasons it may be desirable to limit the maximum
rpm of the fans. These values are programmed into the
maximum fan speed registers (0x34 and 0x35). During AFC,
the fan speed is monitored and is never allowed to exceed the
programmed limit, even if the AFC loop demands it. However,
To use automatic fan control (AFC), a number of parameters
must be set up.
Which Temperature Channel Controls Which Fan?
This is determined by the AFC configuration registers (0x05
and 0x06). AFC1 configuration register controls Fan 1, and
AFC2 configuration register controls Fan 2. Setting bits in these
registers decides which temperature channels controls the fan.
the maximum fan speed limit can be overridden by a
THERM
event, which sets the fan drive to full scale (full speed) for
emergency cooling.
Table 29. AFC Configuration Registers
Operating Temperature Range
Bit
Description
The temperature range over which AFC operates can be
programmed by using the TMIN and TRANGE registers.
Bit 0
Bit 1
Bit 2
Bit 3
Bit 4
Bit 5
Bit 6
Bit 7
Fan controlled by TH1 or REM2
Fan controlled by TH2
Fan controlled by Remote Temperature 1
Fan controlled by local temperature
Fan under manual control
Fan at minimum speed
TMIN is the temperature at which a fan starts and runs at
minimum speed when in AFC mode. TRANGE is the
temperature range over which AFC operates. Thus, if TMIN is
set to 40°C and TRANGE is set to 20°C, the fan starts when the
temperature exceeds 40°C and the fan reaches maximum speed
at a temperature of 60°C.
Fan at start-up speed
Fan at maximum speed
Enhanced Acoustics
If more than one of the temperature channel Bits 0:3 are set, the
channel that demands the highest fan speed takes control.
When TH1 and TH2 are set up as AIN1 and AIN2, these pins
still control the AFC loop if Bits 0:1 in the AFC configuration
register are set. Bits 0:1 should not be set in analog input mode.
When fan speed is controlled automatically, a temperature event
can cause the fan drive output to change instantaneously to a new
value. The sudden subsequent change in fan speed can cause an
audible noise pulse. To avoid this problem, the ADT7466 can be
programmed so that the drive value changes in a series of small
steps, using the enhanced acoustics register (0x36).
If the manual control bit is set, AFC is switched off and the
DRIVE registers can be programmed manually. This overrides
any setting of the temperature channel bits. The maximum
RPM registers, 0x34 and 0x35, should be set to 0x00 when the
fans are under manual control.
Bits 2:0 of this register allow eight step sizes from 1 to 48 bits to
be selected for Fan 1. Bits 5:3 do the same for Fan 2. When
automatic fan control requires a change in drive value, the value
changes by the step size once every 250 ms until the final value
is reached. For example, if the step size is 3 and the drive value
changes from 137 to 224, the drive value takes 29 ms × 250 ms
to reach its final value.
If the minimum speed bit is set, AFC is switched off and the fan
runs at minimum speed. This overrides any setting of Bits 4:0.
If the start-up speed bit is set, AFC is switched off and the fan
runs at start-up speed. This overrides any setting of Bits 5:0.
Enhanced acoustics for the Fan 1 output (DRIVE1) can be
enabled by setting Bit 6 of the enhanced acoustics register, and
by setting Bit 7 for Fan 2 (DRIVE2).
If the maximum speed bit is set, AFC is switched off and the fan
runs at maximum speed. This overrides any setting of Bits 6:0.
Rev. 0 | Page 29 of 48
ADT7466
AFC Loop Operation
STARTING THE FAN
The automatic fan speed control loop operates as follows.
Under normal conditions, the V_FAN_ON register sets DRIVE
at a voltage sufficient to start the fan rotating. Fan startup is
confirmed after two tach pulses are generated.
Once the temperature exceeds T_MIN, the ADT7466 outputs
the voltage V_FAN_ON on its DRIVE pin. For Fan 1, FAN1 ON
is also asserted. When the fan starts rotating reliably, the drive
voltage is reduced to V_FAN_MIN. Reliable startup is
determined when two tachometer pulses are sensed on the tach
input. As the measured temperature increases, the voltage
output by the ADT7466 also increases linearly. The rate with
which the voltage output (fan speed) increases is controlled by
the T_RANGE parameter.
1. Set the initial V_FAN_ON by BIOS.
2. Wait for two tach pulses (up to 2 seconds maximum).
3. If successful, set the drive to V_FAN_MIN and follow the
automatic slope.
If not successful, increase the V_FAN_ON voltage on
DRIVE by a programmed value (set in step size register)
and return to Step 1. This sequence can be repeated five
times or until DRIVE is set at full scale. If the fan still fails
Once the measured fan speed reaches a programmable
maximum limit, the fan speed does not increase further. This is
to maintain low acoustics. If, however, the
fail safe
THERM
to start, the
pin is asserted.
FANLOCK
limit is breached, the fans immediately run to full speed (0xFF).
They continue to run at full speed until the temperature falls by
4. Set the drive at 0 V (to avoid high power dissipation).
a programmable hysteresis value below the
the fan speed reduces to its value before the
exceeded.
limit. Then
THERM
5. Wait 1 minute and repeat the entire sequence. (This
sequence recovers the situation if the fan is temporarily
stalled due a mechanical reason such as jammed with a
stick.)
limit is
THERM
As the temperature decreases, the fan speed decreases along the
same curve. Once the temperature falls below T_MIN, the fan
runs at V_FAN_MIN. If the temperature continues to decrease,
the fan can continue to run at V_FAN_MIN, or if the
temperature drops below a hysteresis value, the fan can be
switched off completely. This is controlled by Bits 4:5 of
Configuration Register 4. Setting these bits ensures that the fans
never go below minimum speed. FAN 1 ON is also deasserted
when the fan drive is set to 0 V.
FAN DRIVE V
FULL SPEED
2.25V
(0xFF)
V_FAN_ON
V_FAN_MIN
The fan speed is updated every 250 ms to 500 ms in the
automatic fan speed control loop.
FAN OFF
0V
(0x00)
TMIN
T_THERM_HYS
FAN DRIVE V
TACHO
FULL SPEED
2.25V
(0xFF)
MAX FAN
SPEED
Figure 42. Normal Fan Starting Timing Diagram
FAN SPIN UP
FOR 2 TACH
PULSES
FAN DRIVE V
FULL SPEED
2.25V
V_FAN_ON
V_FAN_MIN
(0xFF)
V_FAN_ON_STEP
V_FAN_ON
FAN OFF
0V
(0x00)
TMIN
TMAX
V_FAN_MIN
TEMPERATURE
TRANGE
FAN OFF
0V
(0x00)
TMIN_HYS
1MIN
T_THERM
2SEC
Figure 41. Operation of AFC Loop
FAN1_ON
FAN_LOCK
Figure 43. Abnormal Fan Starting (Fan Stalled)
Rev. 0 | Page 30 of 48
ADT7466
XOR TEST MODE
SCL
The ADT7466 includes an XOR tree test mode. This mode is
useful for in-circuit test equipment at board-level testing. By
applying stimulus to the pins included in the XOR tree, it is
possible to detect opens or shorts on the system board. Figure 44
shows the signals that are exercised in the XOR tree test mode.
TACH1
SDA
PROCHOT
ALERT
The XOR tree test is invoked by setting Bit 0 (XEN) of the XOR
tree test enable register (0x42). Pin 7 should be configured as a
DRIVE1
input by setting Bit 1 (P7C1) of Configuration
PROCHOT
TACH2
Register 3 (0x02). The
should also be set.
mask bit (Reg. 0x13, Bit 1)
PROCHOT
Figure 44. ADT7466 XOR Tree
Rev. 0 | Page 31 of 48
ADT7466
APPLICATION CIRCUIT
Figure 45 shows a typical application circuit diagram for the
ADT7466. The analog inputs are configured for thermistor
temperature monitoring. Inputs D+ and D− are used to
measure the temperature of a discrete transistor. In an actual
application, every input and output may not be used. In this
case, unused analog and digital inputs should be tied to ground.
Pull-up resistors are required on SCL, SDA, FAN1_ON,
/
, and
. There are two drive
PROCHOT THERM
FANLOCK
outputs which control the speed of two fans. There are also two
tach inputs from the fans for monitoring the fan speed.
FAN
DRIVE
CIRCUITRY
V
CC
10kΩ
V
CC
V
CC
2kΩ
2kΩ
FAN
DRIVE
10kΩ
1
2
3
4
5
6
7
8
DRIVE1
TACH1
DRIVE2
TACH2
GND
SCL 16
SDA 15
SCLOCK
SDATA
ADT7466
V
CIRCUITRY
CC
10kΩ
SMB_ALERT
TH2
ALERT 14
REFOUT 13
V
CC
AIN2/TH2/D2+ 12
AIN1/TH1/D2– 11
TH1
V
V
CC
CC
10kΩ
10kΩ
FAN1_ON/PROCHOT/THERM
FAN1_ON/PROCHOT/THERM
FANLOCK
D1+ 10
D1–
R
1
R
2
EXT
EXT
FANLOCK
SIGNALS FAN FAILURE
9
2N3904
NPN
Figure 45. Typical Application Circuit
Rev. 0 | Page 32 of 48
ADT7466
ADT7466 REGISTER MAP
Table 30. ADT7466 Registers
Lock-
Addr. R/W Name
0x00 R/W CONF1
0x01 R/W CONF2
0x02 R/W CONF3
0x03 R/W CONF4
0x04 R/W CONF5
0x05 R/W AFC1
0x06 R/W AFC2
0x07
Description
Bit 7
OBIN
REM2
Bit 6
Vcc
Bit 5
TODIS
RATE
DC2
Bit 4
Bit 3
Bit 2
RDY
Bit 1
LOCK
CURR
Bit 0
STRT
RTYPE
P7C0
CH0
Default able
Configuration 1
Configuration 2
Configuration 3
Configuration 4
Reserved
FSPDIS FSPD
AVG
0x01
0x00
0xC0
0x00
0x00
0x0C
0x0C
0x00
0x00
0x00
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
SHDN
REFZ
THER 2 THER1
DC1
FAST
SNGL
BOOST P7C1
MIN2
MIN1
CH2
CH1
AFC1 Configuration
AFC2 Configuration
Reserved
MAX
MAX
7
STRT
STRT
6
MIN
MIN
5
MAN
MAN
4
LOC
LOC
3
REM
REM
2
TH2
TH2
1
TH1
TH1
0
0x08
0x09
R
R
EXT1
EXT2
Extended Resolution 1 AIN1-1 AIN1-0
Extended Resolution 2
AIN2-1
AIN2-0 VCC1
VCC0
REM1
LOC1
REM0
LOC0
AIN1(TH1)/REM2
0x0A
0x0B
0x0C
R
R
R
AIN1
AIN2
VCC
Reading
9
9
9
8
8
8
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
2
0x00
0x00
0x00
AIN2(TH2) Reading
Vcc Reading
Remote1 Temp
Reading
0x0D
0x0E
R
R
REM1
LOC
9
9
8
8
7
7
6
6
5
5
4
4
3
3
2
2
0x00
0x00
Local Temp Reading
ASRT/
TMR0
PROCHOT
Reading
0x0F
R
PCHT
TMR
OOL
TMR
TMR
TMR
TMR
TMR
TMR
0x00
AIN1(TH1)/
REM2
0x10
0x11
R
R
INT1
INT2
Interrupt Status 1
Interrupt Status 2
AIN2(TH2) Vcc
REM1
D2
LOC
D1
FAN1
PHOT
FAN2
OVT
0x00
0x00
TH2
TH1
AIN1(TH1)/
REM2
0x12 R/W MASK1
0x13 R/W MASK2
Interrupt Mask 1
Interrupt Mask 2
OOL
AIN2(TH2) Vcc
REM
D2
LOC
D1
FAN1
PHOT
FAN2
OVT
0x00
0x00
TH2
TH1
AIN1(TH1)/REM2 Low
Limit
0x14 R/W AIN1LOW
7
6
5
4
3
2
1
0
0x00
AIN1(TH1)/REM2 High
Limit
0x15 R/W AIN1HIGH
0x16 R/W AIN2LOW
0x17 R/W AIN2HIGH
0x18 R/W VCCLOW
0x19 R/W VCCHIGH
7
7
7
7
7
6
6
6
6
6
5
5
5
5
5
4
4
4
4
4
3
3
3
3
3
2
2
2
2
2
1
1
1
1
1
0
0
0
0
0
0xFF
0x00
0xFF
0x00
0xFF
AIN2(TH2) Low Limit
AIN2(TH2) High Limit
Vcc Low Limit
Vcc High Limit
Remote1 Temp Low
Limit
0x1A R/W REM1LOW
7
6
5
4
3
2
1
0
0x00
Remote1 Temp High
Limit
0x1B R/W REM1HIGH
0x1C R/W LOCLOW
0x1D R/W LOCHIGH
0x1E R/W PCHTLIM
7
6
5
4
3
2
1
0
0x7F
0x00
0x7F
0x00
Local Temp Low Limit
Local Temp High Limit
7
6
5
4
3
2
1
0
7
6
5
4
3
2
1
0
PROCHOT
Limit
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
LIMT
Yes
AIN1(TH1)/REM2
0x1F R/W AIN1THERM Therm Limit
7
7
7
7
7
6
6
6
6
6
5
5
5
5
5
4
4
4
4
4
3
3
3
3
3
2
2
2
2
2
1
1
1
1
1
0
0
0
0
0
0x64
0x64
0x64
0x64
0x00
Yes
Yes
Yes
Yes
Yes
0x20 R/W AIN2THERM AIN2(TH2) Therm Limit
0x21 R/W REM1THERM Remote 1 Therm Limit
0x22 R/W LOCTHERM Local Therm Limit
0x23 R/W
Reserved
AIN1(TH1)/REM2
Offset
0x24 R/W AIN1OFS
0x25 R/W AIN2OFS
0x26 R/W REM1OFS
0x27 R/W LOCOFS
0x28 R/W AIN1TMIN
0x29 R/W AIN2TMIN
7
7
7
7
7
7
6
6
6
6
6
6
5
5
5
5
5
5
4
4
4
4
4
4
3
3
3
3
3
3
2
2
2
2
2
2
1
1
1
1
1
1
0
0
0
0
0
0
0x00
0x00
0x00
0x00
0x5A
0x5A
Yes
Yes
Yes
Yes
Yes
Yes
AIN2(TH2) Offset
Remote1 Temp Offset
Local Temp Offset
AIN1(TH1)/REM2 TMIN
AIN2(TH2) TMIN
Rev. 0 | Page 33 of 48
ADT7466
Lock-
Addr. R/W Name
Description
Remote1 TMIN
Local TMIN
Bit 7
Bit 6
Bit 5
Bit 4
Bit 3
Bit 2
Bit 1
Bit 0
Default able
0x2A R/W REM1TMIN
0x2B R/W LOCTMIN
7
7
6
6
5
5
4
4
3
3
2
2
1
1
0
0
0x5A
0x5A
Yes
Yes
TH1(REM2)/TH2
TRANGE
0x2C R/W THTRANGE
TH1R3
TH1R2
TH1R1
TH1R0 TH2R3 TH2R2 TH2R1 TH2R0
RM1R0 LOR3 LOR2 LOR1 LOR0
TH1TH0 TH2TH3 TH2TH2 TH2TH1 TH2TH0
0xCC
0xCC
0x44
0x44
0x80
0x80
0x60
0x60
Yes
Yes
Yes
Yes
Yes
Yes
Yes
Yes
0x2D R/W R1LTRANGE REM1,LOC TRANGE
RM1R3 RM1R2
TH1TH3 TH1TH2
RM1H3 RM1H2
RM1R1
0x2E R/W THTHYS
0x2F R/W R1LTHYS
TH1,TH2 THyst
TH1TH1
Rem1/ Local THyst
RM1H1
RM1H0 LOH3
LOH2
LOH1
LOH0
0x30 R/W FAN1START Fan1 Start-up Voltage
0x31 R/W FAN2START Fan2 Start-up Voltage
7
7
7
7
6
6
6
6
5
5
5
5
4
4
4
4
3
3
3
3
2
2
2
2
1
1
1
1
0
0
0
0
0x32 R/W FAN1MIN
0x33 R/W FAN2MIN
Fan1 Min Voltage
Fan2 Min Voltage
Fan1 Max RPM (High
Byte)
0x34 R/W FAN1MAX
0x35 R/W FAN2MAX
7
7
6
6
5
4
4
3
3
2
2
1
1
0
0
0x20
Yes
Fan2 Max RPM (High
Byte)
5
0x20
0x3F
0x3F
Yes
Yes
Yes
0x36 R/W ENHANCED Enhanced Acoustics
FAN2EN FAN1EN
FAN2-2
FAN2-2
FAN2-1 FAN2-0 FAN1-2 FAN1-1 FAN1-0
FAN2-1 FAN2-0 FAN1-2 FAN1-1 FAN1-0
0x37 R/W FAULTINC
Fault Increment
7
6
Startup Timeout
Configuration
0x38 R/W TIMEOUT
ST2-2
ST2-1
ST2-0
ST1-2
ST1-1
ST1-0
0x00
Yes
Fan Pulses per
Revolution
0x39 R/W PULSES
0x3A R/W
FAN2
3
FAN2
2
FAN1
1
FAN1
0
0x05
0x00
Reserved
7
6
5
4
Yes
0x3B R/W
Not Used
0x3C R/W
Not Used
0x3D R/W ID
Device ID Register
Company ID Number
Revision Number
Drive 1
7
6
5
4
3
2
1
0
0x66
0x41
0x02
0x00
0x00
0x00
0x00
0x3E
0x3F
R
R
COMPANY
REV
7
6
5
4
3
2
1
0
VER
7
VER
6
VER
5
VER
4
VER
3
VER
2
VER
1
VER
0
0x40 R/W DRIVE 1
0x41 R/W DRIVE 2
0x42 R/W XOR
0x43 R/W
Drive 2
7
6
5
4
3
2
1
0
XOR Tree Test Enable
Reserved
XEN
0
Yes
Yes
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
2
1
1
1
Reserved (Target
Monitor1)
0x44 R/W
0
0
0x00
0x00
Reserved (Target
Monitor2)
0x45 R/W
0x46 R/W
0x47 R/W
Not Used
Not Used
0x48
0x49
0x4A
0x4B
R
R
R
R
TACH1L
TACH1H
TACH2L
TACH2H
Tach1 Low Byte
Tach1 High Byte
Tach2 Low Byte
Tach2 High Byte
Tach1 Minimum Low
7
6
5
4
3
2
1
9
1
9
0
8
0
8
0xFF
0xFF
0xFF
0xFF
15
7
14
6
13
5
12
4
11
3
10
2
15
14
13
12
11
10
0x4C R/W TACH1LOW Byte
Tach1 Minimum High
0x4D R/W TACH1HIGH Byte
Tach2 Minimum Low
0x4E R/W TACH2LOW Byte
Tach2 Minimum High
0x4F R/W TACH2HIGH Byte
7
7
7
6
6
6
5
5
5
4
4
4
3
3
3
2
2
2
1
1
1
0
0
0
0xFF
0xFF
0xFF
7
7
7
7
7
6
6
6
6
6
5
5
5
5
5
4
4
4
4
4
3
3
3
3
3
2
2
2
2
2
1
1
1
1
1
0
0
0
0
0
0xFF
0x00
0x00
0x00
0x00
0x50 R/W TEST1
0x51 R/W TEST2
0x52 R/W TEST3
0x53 R/W TEST4
Test Register1
Yes
Yes
Yes
Yes
Test Register2
Test Register3
Test Register4
Rev. 0 | Page 34 of 48
ADT7466
REGISTER DETAILS
Configuration 1
Table 31. Register 0x00—Configuration Register 1 (Power-On Default = 0x01)
Bit No. Name
Read/Write Description
0
STRT
Read/Write
Logic 1 enables monitoring, and PWM control outputs based on the limit settings programmed.
Logic 0 disables monitoring and PWM control based on the default power-up limit settings. The limit
values programmed are preserved even if a Logic 0 is written to this bit and the default settings are
enabled. This bit becomes read only and cannot be changed once Bit 1 (LOCK bit) is written. All limit
registers should be programmed by BIOS before setting this bit to 1. Lockable.
1
2
LOCK
Write Once
Logic 1 locks all limit values to their current settings. Once this bit is set, all lockable registers become
read only and cannot be modified until the ADT7466 is powered down and powered up again. This
prevents rogue programs such as viruses from modifying critical system limit settings. Lockable.
This bit is set to 1 by the ADT7466 to indicate that the device is fully powered up and ready to begin
systems monitoring.
When this bit is 1, it runs all fans at full speed. Power-on default is 0. This bit is not locked at any time.
Logic 1 disables fan spin-up for two tach pulses. Instead, the DAC outputs go high for the entire fan
spin-up timeout selected.
RDY
Read Only
Read/Write
3
4
FSPD
FSPDIS Read/Write
5
6
TODIS
VCC
Read/Write
Read/Write
When this bit is 1, the SMBus timeout feature is disabled. This allows the ADT7466 to be used with
SMBus controllers that cannot handle SMBus timeouts. Lockable.
When this bit is 1, the ADT7466 rescales its VCC pin to measure a 5 V supply.
When this bit is 0, the ADT7466 measures VCC as a 3.3 V supply. Lockable.
When this bit is 0 (default) temperature data format is binary.
When this bit is 1, format is offset binary.
7
OBIN
Read/Write
Configuration 2
This register becomes read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to this register have no
effect.
Table 32. Register 0x01—Configuration Register 2 (Power-On Default = 0x00)
Bit No.
Name
Read/Write Description
0
RTYPE
Read/Write
When this bit is cleared (default), thermistor normalization is optimized for 100 kΩ thermistors. When
this bit is set, it is optimized for 10 kΩ thermistors.
This bit sets the thermal diode current. It should be left at 0.
Setting this bit makes the REFOUT pin high impedance.
Unused. Write ignored. Reads back 0.
When AVG is 1, averaging on the temperature and voltage measurements is turned off. This allows
measurements on each channel to be made much faster.
1
2
3
4
CURR
REFZ
Unused
AVG
Read/Write
Read/Write
–
Read/Write
5
6
7
RATE
SHDN
REM2
Read/Write
Read/Write
Read/Write
If averaging is turned off and measurement set to single channel mode, the RATE bit sets the
conversion rate. 0 = 32 conversions/second; 1 = 4 conversions/second.
When SHDN is 1, the ADT7466 goes into shutdown mode. Both DAC outputs are set to 0 V to switch off
both fans. The DAC registers read back 0x00 to indicate that the fans are not being driven.
Setting this bit configures AIN1 and AIN2 for connection of a second thermal diode. Setting this bit
overrides THER1 and THER2 in Configuration Register 3.
Rev. 0 | Page 35 of 48
ADT7466
Configuration 3
This register becomes read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to this register have no
effect. Bits 4:5 are not locked.
Table 33. Register 0x02—Configuration Register 3 (Power-On Default = 0xC0)
Bit No.
Name
Read/Write
Description
1:0
P7CONFIG
Read/Write
These bits configure Pin 7 as either FAN1_ON output, THERM output or PROCHOT input.
00 = FAN1_ON output
01 = THERM output
1X = PROCHOT input
2
3
4
5
6
BOOST
FAST
DC1
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
When BOOST is set to 1, assertion of PROCHOT causes all fans to run at 100% duty cycle for fail
safe cooling.
Setting this bit to 1 enables fast tach measurements on all channels. This increases the tach
measurement rate from once a second, to one every 250 ms (4×).
Setting this bit to 1 enables tach measurements to be continuously made on TACH1. Not
lockable.
Setting this bit to 2 enables tach measurements to be continuously made on TACH2. Not
lockable.
DC2
THER2
Setting this bit to 1 configures AIN1 as a thermistor input.
Setting this bit to 0 configures for analog input.
7
THER1
Read/Write
Setting this bit to 1 configures AIN2 as a thermistor input.
Setting this bit to 0 configures for analog input.
Configuration Register 4
Table 34. Register 0x03—Configuration Register 4 (Power-On Default = 0x00)
Bit No.
Name
R/W
Description
2:0
CH2:0
Read/Write
These bits select the input channel when SNGL bit is set.
011 = Remote 1 temperature
100 = Local temperature
101 = Remote 2 temperature
3
4
5
6
7
SNGL
MIN1
MIN2
Unused
Unused
Read/Write
Read/Write
Read/Write
Read only
Read only
Setting this bit selects single channel measurement.
When this bit is set, Fan 1 never goes below minimum speed setting.
When this bit is set, Fan 2 never goes below minimum speed setting.
Unused. Write ignored. Reads back 0.
Unused. Write ignored. Reads back 0.
AFC1 Configuration
If more than one of Bits 0:3 are set, the fan speed is controlled by whichever temperature channel demands the highest fan speed.
Table 35. Register 0x05—AFC Configuration Register 1 (Power-On Default = 0x0C)
Bit No.
Name
Read/Write Description
0
TH1/REM2
Read/Write
When this bit is set, Fan 1 speed is controlled by TH1 if Pin 11 is configured for thermistor, or by
Thermal Diode 2 if Pin 11 is configured for thermal diode.
1
2
3
4
TH2
REM1
LOC
Read/Write
Read/Write
Read/Write
Read/Write
When this bit is set, Fan 1 speed is controlled by TH2 if Pin 12 is configured for thermistor.
When this bit is set, Fan 1 speed is controlled by Remote Temperature Input 1.
When this bit is set, Fan 1 speed is controlled by local temperature input.
When this bit is set, Fan 1 speed is under user control by writing directly to the DRIVE1 register. This
overrides all lower bit settings
MAN
5
6
7
MIN
STRT
MAX
Read/Write
Read/Write
Read/Write
When this bit is set, Fan 1 runs at minimum speed. This overrides all lower bit settings.
When this bit is set, Fan 1 runs at start-up speed. This overrides all lower bit settings.
When this bit is set, Fan 1 runs at maximum speed. This overrides all lower bit settings.
Rev. 0 | Page 36 of 48
ADT7466
AFC2 Configuration
If more than one of Bits 0:3 are set, the fan speed is controlled by whichever temperature channel demands the highest fan speed.
Table 36. Register 0x06—AFC Configuration Register 2 (Power-On Default = 0x0C)
Bit No.
Name
Read/Write Description
0
TH1/REM2
Read/Write
When this bit is set, Fan 2 speed is controlled by TH1 if Pin 11 is configured for thermistor, or by
Thermal Diode 2 if Pin 11 is configured for thermal diode.
1
2
3
4
T H2
REM1
LOC
Read/Write
Read/Write
Read/Write
Read/Write
When this bit is set, Fan 2 speed is controlled by TH2 if Pin 12 is configured for thermistor.
When this bit is set, Fan 2 speed is controlled by Remote Temperature Input 1.
When this bit is set, Fan 2 speed is controlled by the local temperature input.
When this bit is set, Fan 2 speed is under user control by writing directly to the DRIVE2 register. This
overrides all lower bit settings.
MAN
5
6
6
MIN
STRT
MAX
Read/Write
Read/Write
Read/Write
When this bit is set, Fan 2 runs at minimum speed. This overrides all lower bit settings.
When this bit is set, Fan 2 runs at startup speed. This overrides all lower bit settings.
When this bit is set, Fan 2 runs at maximum speed. This overrides all lower bit settings.
Extended Resolution 1
Table 37. Register 0x08—Extended Resolution Register 1 (Power-On Default = 0x00)
Bit No.
Name
REM0
REM1
VCC0
Read/Write Description
0
1
2
3
4
5
6
7
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Read only
LSB of remote temperature reading.
Bit 1 of remote temperature reading.
LSB of VCC reading.
Bit 1 of VCC reading.
LSB of AIN2 reading.
Bit 1 of AIN2 reading
LSB of AIN1 reading.
Bit 1 of AIN1 reading.
VCC1
AIN2-0
AIN2-1
AIN1-0
AIN1-1
Extended Resolution 2
Table 38. Register 0x09—Extended Resolution Register 2 (Power-On Default = 0x00)
Bit No.
Name
Read/Write
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Description
0
1
2
3
4
5
6
7
LOC0
LOC1
LSB of local temperature reading.
Bit 1 of local temperature reading.
Not used. Reads back 0.
Not used. Reads back 0.
Not used. Reads back 0.
Not used. Reads back 0.
Not used. Reads back 0.
Not used. Reads back 0.
Unused
Unused
Unused
Unused
Unused
Unused
Voltage Reading
If the extended resolution bits of these readings are also being read, Extended Resolution Register 1 (0x08) should be read first. Once the
extended resolution register is read, it and the associated MSB reading registers are frozen until read.
Table 39. Voltage Reading Registers (Power-On Default = 0x00)
Register Address
Read/Write
Read only
Read only
Read only
Description
0x0A
0x0B
0x0C
AIN1(TH1)/REM2 reading (8 MSBs of reading).
AIN2(TH2) reading (8 MSBs of reading).
VCC reading. Measures VCC through the VCC pin (8 MSBs of reading).
Rev. 0 | Page 37 of 48
ADT7466
Temperature Reading
If the extended resolution bits of these readings are also being read, the extended resolution registers (0x08, 0x09) should be read first.
Once the extended resolution register gets read, all associated MSB reading registers get frozen until read. Both the extended resolution
register and the MSB registers are frozen.
Table 40. Temperature Reading Registers (Power-On Default = 0x00)
Register Address
Read/Write
Read only
Read only
Description
0x0D
0x0E
Remote Temperature 1 reading (8 MSBs of reading).
Local temperature reading (8 MSBs of reading).
PROCHOT
Table 41. Register 0x0F—
Register (Power-On Default = 0x00)
PROCHOT
Bit No.
Name
Read/Write
Description
7:1
TMR
Read only
Times for how long THERM input is asserted. These 7 bits read 0 until the PROCHOT assertion
time exceeds 45.52 ms.
0
ASRT/TMR0 Read only
Set high on the assertion of the THERM input.
Cleared on read. If the PROCHOT assertion time exceeds 45.52 ms, this bit is set and becomes the
LSB of the 8-bit TMR reading. This allows PROCHOT assertion times from 45.52 ms to 5.82
seconds to be reported back with a resolution of 22.76 ms.
Interrupt Status 1
Table 42. Register 0x10—Interrupt Status Register 1 (Power-On Default = 0x00)
Bit No. Name Read/Write Description
0
1
2
3
4
5
6
7
FAN2
FAN1
LOC
Read only
Read only
Read only
Read only
Read only
Read only
Setting this bit to 1 indicates that Fan 2 has dropped below minimum speed or has stalled. This
bit is not set when the DRIVE2 output is off.
Setting this bit to 1 indicates that Fan 1 has dropped below minimum speed or has stalled. This
bit is not set when the DRIVE1 output is off.
Setting this bit to 1 indicates that the local temperature reading is out of limit. This bit is
cleared on a read of the status register only if the error condition clears.
Setting this bit to 1 indicates that Remote Temperature 1 reading is out of limit. This bit is
cleared on a read of the status register only if the error condition clears.
Setting this bit to 1 indicates that the VCC reading is out of limit. This bit is cleared on a read of
the status register only if the error condition clears.
Setting this bit to 1 indicates that the AIN2(TH2) reading is out of limit. This bit is cleared on a
read of the status register only if the error condition clears.
Setting this bit to 1 indicates that the AIN1(TH1)/REM2 reading is out of limit. This bit is cleared
on a read of the status register only if the error condition clears.
REM1
VCC
AIN2(TH2)
AIN1(TH1)/REM2 Read only
OOL Read only
Setting this bit to 1 indicates that an out-limit event is latched in Status Register 2. This bit is a
logical OR of all status bits in Status Register 2. Software can test this bit in isolation to
determine whether any of the voltage, temperature, or fan speed readings represented by
Status Register 2 are out of limit. This saves the need to read Status Register 2 during every
interrupt or polling cycle.
Rev. 0 | Page 38 of 48
ADT7466
Interrupt Status 2
Table 43. Register 0x11—Interrupt Status Register 2 (Power-On Default = 0x00)
Bit No.
Name
Read/Write
Description
Setting this bit to 1 indicates that one of the THERM overtemperature limits has been exceeded.
This bit is cleared automatically when the temperature drops below THERM − THYST
0
OVT
Read only
.
1
PHOT
Read only
If Pin 7 is configured as the input for PROCHOT monitoring, this bit is set when the PROCHOT
assertion time exceeds the limit programmed in the PROCHOT limit register (0x1E).
2
3
4
5
6
7
D1
D2
TH1
TH2
Unused
Unused
Read only
Read only
Read only
Read only
Read only
Read only
Setting this bit to 1 indicates either an open or a short circuit on the Thermal Diode 1 inputs.
Setting this bit to 1 indicates either an open or a short circuit on the Thermal Diode 2 inputs.
Setting this bit to 1 indicates either an open or a short circuit on the TH1 input.
Setting this bit to 1 indicates either an open or a short circuit on the TH2 input.
Not used. Reads back 0.
Not used. Reads back 0.
Interrupt Mask 1
Table 44. Register 0x12—Interrupt Mask Register 1 (Power-On Default = 0x00)
Bit No.
Name
FAN2
FAN1
LOC
Read/Write
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Description
0
1
2
3
4
5
6
Setting this bit masks the Fan 2 interrupt from the ALERToutput.
Setting this bit masks the Fan 1 interrupt from the ALERT output.
Setting this bit masks the local temperature. interrupt from the ALERT output.
Setting this bit masks the remote temperature interrupt from the ALERT output.
Setting this bit masks the VCC interrupt from the ALERT output.
Setting this bit masks the AIN2(TH2) interrupt from the ALERT output.
Setting this bit masks the AIN1(TH1)/REM2 interrupt from the ALERT output.
REM
VCC
AIN2(TH2)
AIN1
/TH1/REM2
7
OOL
Read only
Setting this bit masks the OOL interrupt from the ALERT output.
Interrupt Mask 2
Table 45. Register 0x13—Interrupt Mask Register 2 (Power-On Default = 0x00)
Bit No.
Name
Read/Write
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Read only
Description
Setting this bit masks the OVT interrupt from ALERT output.
Setting this bit masks the THERM interrupt from ALERT output.
Setting this bit masks the Thermal Diode 1 fault interrupt from ALERT output.
Setting this bit masks Thermal Diode 2 fault interrupt from ALERT output.
Setting this bit masks the TH1 fault interrupt from ALERT output.
Setting this bit masks the TH2 fault interrupt from ALERT output.
Not used. Reads back 0.
0
1
2
3
4
5
6
7
OVT
PHOT
D1
D2
TH1
TH2
Unused
Unused
Not used. Reads back 0.
Rev. 0 | Page 39 of 48
ADT7466
Voltage Limit
Setting the Configuration Register 1 lock bit has no effect on these registers.
High limits: An interrupt is generated when a value exceeds its high limit (> comparison).
Low limits: An interrupt is generated when a value is equal to or below its low limit (≤ comparison).
Table 46. Voltage Limit Registers
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
Power-On Default
0x14
0x15
0x16
0x17
0x18
0x19
AIN1(TH1)/REM2 low limit.
AIN1(TH1)/REM2 high limit.
AIN2(TH2) low limit.
AIN2(TH2) high limit.
VCC low limit.
0x00
0xFF
0x00
0xFF
0x00
0xFF
VCC high limit.
Temperature Limit
Setting the Configuration Register 1 lock bit has no effect on these registers. When the temperature readings are in offset binary format,
an offset of 64 degrees (0x40 or 0100000) must be added to all temperature and
limits. For example, if the limit is 50°C the
THERM
actual programmed limit is 114.
High limits: An interrupt is generated when a value exceeds its high limit (> comparison).
Low limits: An interrupt is generated when a value is equal to or below its low limit (≤ comparison).
Table 47. Temperature Limit Registers
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
Power-On Default
0x1A
0x1B
0x1C
0x1D
Remote 1 Temperature low limit.
Remote 1 Temperature high limit.
Local temperature low limit.
Local temperature high limit.
0x00
0x7F
0x00
0x7F
Limit
PROCHOT
This is an 8-bit limit with a resolution of 22.76 ms allowing
assertion limits of 45.52 ms to 5.82 seconds to be programmed. If
PROCHOT
the
assertion time exceeds this limit, Bit 1 of Interrupt Status Register 2 (0x11) is set. If the limit value is 0x00, an interrupt is
PROCHOT
generated immediately upon assertion of the
input.
THERM
Table 48. Register 0x1E—
Limit Register (Power-On Default = 0x00)
Description
PROCHOT
Read/Write
Read/Write
Bit No.
Name
7:0
LIMT
Sets maximum PROCHOT assertion length allowed before an interrupt is generated.
Rev. 0 | Page 40 of 48
ADT7466
THERM
Limit
THERM
If any temperature measured exceeds its
limit, both DRIVE outputs drive their fans at maximum output. This is a failsafe
mechanism incorporated to cool the system in the event of a critical overtemperature. It also ensures some level of cooling in the event
that software or hardware locks up. If set to 0x00, this feature is disabled. The DRIVE output remains at 0xFF until the temperature drops
THERM
THERM
THERM
below
limit − hysteresis. If the
pin is programmed as an output, exceeding these limits by 0.25°C can cause the
pin to assert low as an output.
These registers become read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to these registers
have no effect.
THERM
Register Address
Table 49.
Limit Registers
Read/Write
Description
Power-On Default
0x64 (100°C)
0x1F
0x20
0x21
0x22
Read/Write
Read/Write
Read/Write
Read/Write
AIN1/TH1REM2 THERM limit.
AIN2(TH2) THERM limit.
Remote 1 THERM limit.
Local THERM limit.
0x64 (100°C)
0x64 (100°C)
0x64 (100°C)
Temperature Offset
These registers contain an 8-bit, twos complement offset value that is automatically added to or subtracted from the temperature reading
to compensate for any systematic errors such as those caused by noise pickup. LSB value = 1°C.
This register becomes read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to this register have no
effect.
Table 50. Temperature Offset Registers
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
Power-On Default
0x24
0x25
0x26
0x27
AIN1(TH1)/REM2 offset.
AIN2(TH2) offset.
Remote 1 offset.
Local offset.
0x00
0x00
0x00
0x00
TMIN
These registers contain the TMIN temperatures for automatic fan control (AFC). These are the temperatures above which the fan starts to
operate. The data format is either binary or offset binary, the same as the temperature reading, depending on which option is chosen by
setting or clearing Bit 7 of Configuration Register 1.
These registers become read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to these registers
have no effect.
Table 51. TMIN Registers
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
Power-On Default
0x5A (90°C)
0x5A (90°C)
0x5A (90°C)
0x5A (90°C)
0x28
0x29
0x2A
0x2B
AIN1(TH1)/REM2 TMIN.
AIN2(TH2) TMIN
Remote 1 TMIN
Local TMIN
.
.
.
Rev. 0 | Page 41 of 48
ADT7466
Table 52. TMIN Codes
Temperature
-64°C
0°C
1°C
10°C
25°C
50°C
75°C
100°C
125°C
127°C
191°C
Binary
Offset Binary
0 000 0000
0 100 0000
0 100 0001
0 100 1010
0 101 1001
0 111 0010
1 000 1011
1 010 0100
1 011 1101
1 011 1111
1 111 1111
0 000 0000
0 000 0000
0 000 0001
0 000 1010
0 001 1001
0 011 0010
0 100 1011
0 110 0100
0 111 1101
0 111 1111
0 111 1111
THT Range
Table 53. Register 0x2C—THTRANGE Register (Power-On Default = 0xCC)
Bit No.
Name
Read/Write
Description
3:0
TH2R
Read/Write
These bits set the temperature range over which AFC operates for the TH2 input. The fan starts
operating at TM and reaches full speed at TM+ TR (where TM is the temperature set by the TMIN
code, and TR is the temperature range set by the TRANGE code).
7:4
TH1R
Read/Write
These bits set the temperature range over which AFC operates for the TH1 or REM2 input. The fan
starts operating at TM and reaches full speed at TM+ TR (where TM is the temperature set by the
TMIN code, and TR is the temperature range set by the TRANGE code).
Remote and Local TRANGE
Table 54. Register 0x2D—Remote and Local TRANGE Register (Power-On Default = 0xCC)
Bit No.
Name
Read/Write
Description
3:0
LOR
Read/Write
These bits set the temperature range over which AFC operates for the local temperature input.
The fan starts operating at TM and reaches full speed at TM + TR (where TM is the temperature set
by the TMIN code, and TR is the temperature ranges set by the TRANGE code).
7:4
RMR
Read/Write
These bits set the temperature range over which AFC operates for the Remote 1 (D1)
temperature input. The fan starts operating at TM and reaches full speed at TM + TR (where TM is
the temperature set by the TMIN code, and TR is the temperature range set by the TRANGE code).
Table 55. TRANGE Codes
Bits 7:4 or 3:0
TRANGE
2°C
0000
0001
2.5°C
0010
0011
3.33°C
4°C
0100
5°C
0101
0110
6.67°C
8°C
0111
10°C
1000
1001
13.33°C
16°C
1010
20°C
1011
1100
1101
26.67°C
32°C (default)
40°C
1110
1111
53.33°C
80°C
Rev. 0 | Page 42 of 48
ADT7466
TH1/TH2 Hysteresis
Table 56. Register 0x2E—TH1/TH2 Hysteresis Register (Power-On Default = 0x44)
Bit No.
Name
Read/Write
Description
7:4
TH1TH
Read/Write
This nibble contains the temperature hysteresis value for TH1/REM2. 0x0 =
0°C to 0xF = 15°C.
3:0
TH2TH
Read/Write
This nibble contains the temperature hysteresis value for TH2. 0x0 = 0°C to
0xF = 15°C.
REM/LOC Hysteresis
Table 57. Register 0x2F—REM/LOC Hysteresis Register (Power-On Default = 0x44)
Bit No.
Name
Read/Write
Description
7:4
RM1H
Read/Write
This nibble contains the temperature hysteresis value for remote temperature
input. 0x0 = 0°C to 0xF = 15°C.
3:0
LOH
Read/Write
This nibble contains the temperature hysteresis value for local temperature
input. 0x0 = 0°C to 0xF = 15°C.
Fan Start-Up Voltage
This is the voltage output from the fan drive output for two tach periods after it first starts up. Taking gain into account, the fan drive
amplifier should be chosen so the voltage applied to the fan is sufficiently high to ensure that the fan starts.
Table 58. Fan Start-Up Voltage Registers (Power-On Default = 0x80)
Register Address
Read/Write
Read/Write
Read/Write
Description
0x30
0x31
Fan 1 start-up voltage.
Fan 2 start-up voltage.
Fan Maximum Voltage
This is the minimum voltage output from the fan drive output after the fan spins up, in the absence of any other speed control input.
Table 59. Fan Minimum Voltage Registers (Power-On Default = 0x60)
Register Address
Read/Write
Read/Write
Read/Write
Description
0x32
0x33
Fan 1 minimum voltage.
Fan 2 minimum voltage.
Fan Maximum RPM
This is the maximum RPM that the fan can run at in AFC mode.
Table 60. Fan Maximum RPM Registers (Power-On Default = 0x20)
Register Address
Read/Write
Read/Write
Read/Write
Description
0x34
0x35
Fan 1 maximum RPM.
Fan 2 maximum RPM.
Rev. 0 | Page 43 of 48
ADT7466
Enhanced Acoustics
Table 61. Register 0x36—Enhanced Acoustics Register (Power-On Default = 0x3F)
Bit No.
Name
Read/Write
Description
2:0
5:3
FAN1 Step
FAN2 Step
Read/Write
Read/Write
These bits set the step size by which the DRIVE1 and DRIVE2 PWM output
duty-cycle can change when enhance acoustics mode is selected.
000 = 1 bit
001 = 2 bits
010 = 3 bits
011 = 5 bits
100 = 8 bits
101 = 12 bits
110 = 24 bits
111 = 48 bits
6
7
Enable Fan1
Enhanced
Acoustics
Enable Fan2
Enhanced
Acoustics
Read/Write
Read/Write
When this bit is set to 1, enhanced acoustics are enabled for Fan 1.
When this bit is set to 1, enhanced acoustics are enabled for Fan 2.
Fault Increment
Table 62. Register 0x37—Fault Increment Register (Power-On Default = 0x3F)
Bit No.
Name
Read/Write
Read/Write
Read/Write
Description
2:0
5:3
FAN1Fault
FAN2 Fault
These bits set the step size by which the DRIVE1 and DRIVE2 PWM output
duty-cycle can change in fan fault mode.
000 = 1 bit
001 = 2 bits
010 = 3 bits
011 = 5 bits
100 = 8 bits
101 = 12 bits
110 = 24 bits
111 = 48 bits
7:6
Unused
–
Unused. Write ignored. Reads back 0.
Start-Up Timeout Configuration
Table 63. Register 0x38—Start-Up Timeout Configuration Register (Power-On Default = 0x00)
Bit No.
Name
Read/Write
Read/Write
Read/Write
Description
2:0
5:3
ST1
ST2
These bits set the start-up timeout for Fan 1.
These bits set the start-up timeout for Fan 2.
000 = No start-up timeout
001 = 100 ms
010 = 250 ms
011 = 400 ms
100 = 667 ms
101 = 1second
110 = 2 seconds
111 = 4 seconds
7:6
Unused
–
Unused. Write ignored. Reads back 0.
Rev. 0 | Page 44 of 48
ADT7466
Fan Pulses Per Revolution
Table 64. Register 0x39—Fan Pulses Per Revolution Register (Power-On Default = 0x05)
Bit No.
Name
Read/Write
Description
1:0
FAN1
Read/Write
Sets number of pulses to be counted when measuring FAN1 speed. Can be
used to determine fan’s pulses per revolution number for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
3:2
7:4
FAN2
Read/Write
Sets number of pulses to be counted when measuring FAN2 speed. Can be
used to determine fan’s pulses per revolution number for unknown fan type.
Pulses Counted
00 = 1
01 = 2 (default)
10 = 3
11 = 4
Unused
–
Unused. Write ignored. Reads back 0.
Information Registers
Table 65. Register 0x3D—Device ID Register (Power-On Default = 0x66)
Bit No.
Name
Read/Write
Description
7:0
Reserved
Read only
Contains device ID number.
Table 66. Register 0x3E—Company Id Register (Power-On Default = 0x41)
Bit No.
Name
Read/Write
Description
7:0
Reserved
Read only
Contains company ID number.
Table 67. Register 0x3F—Revision Number Register (Power-On Default = 0x02)
Bit No.
Name
Read/Write
Description
7:0
Reserved
Read only
Contains device revision level.
Fan Drive (DAC)
These registers reflect the drive value of each fan at any given time. When in automatic fan speed control mode, the ADT7466 reports the
drive values back through these registers. The fan drive values vary according to temperature in automatic fan speed control mode.
During fan startup, these registers report 0x00. In software mode, the fan drive outputs can be set to any value by writing to these
registers.
Table 68. Fan Drive (DAC) Registers (Power-On Default = 0x00)
Register Address
Read/Write
Read/Write
Read/Write
Description
0x40
0x41
DRIVE1, Current Fan 1 drive value.
DRIVE2, Current Fan 2 drive value.
XOR Tree Test Enable
This register becomes read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to this register have no
effect.
Table 69. Register 0x42—XOR Tree Test Enable (Power-On Default = 0x00)
Bit No.
Name
Reserved
XEN
Read/Write
Description
7:1
0
–
Unused. Do not write to these bits.
If the XEN bit is set to 1, the device enters the XOR tree test mode. Clearing the bit
removes the device from the XOR test mode.
Read/Write
Rev. 0 | Page 45 of 48
ADT7466
Fan Tachometer Reading
These registers count the number of 12.43 µs periods (based on a local 82 kHz clock) that occur between a number of consecutive fan
tach pulses (default = 2). The number of tach pulses used to count can be changed by using the fan pulses per revolution register (0x39).
This allows the fan speed to be accurately measured. Since a valid fan tachometer reading requires two bytes to be read, the low byte must
be read first. Both the low and high bytes are then frozen until read. At power-on, these registers contain 0x0000 until such time as the
first valid fan tach measurement is read into these registers. This prevents false interrupts from occurring while the fans are spinning up.
A count of 0xFFFF indicates that a fan is
•
•
•
Stalled or blocked (object jamming the fan).
Failed (internal circuitry destroyed).
Not populated (the ADT7466 expects to see a fan connected to each tach. If a fan is not connected to that tach, its tach minimum
high and low byte should be set to 0xFFFF).
•
2-wire instead of 3-wire.
Table 70. Fan Tachometer Reading Registers (Power-On Default = 0xFF)
Register Address
Read/Write
Read only
Read only
Read only
Read only
Description
0x48
0x49
0x4A
0x4B
TACH1 low byte
TACH1 high byte
TACH2 low byte
TACH2 high byte
Fan Tachometer Limit
Exceeding any of the tach limit registers by 1 indicates that the fan is running too slowly or has stalled. The appropriate status bit is set in
Interrupt Status Register 1 to indicate the fan failure. Setting the Configuration Register 1 lock bit has no effect on these registers.
Table 71. Fan Tachometer Limit Registers (Power-On Default = 0xFF)
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
0x4C
0x4D
0x4E
0x4F
TACH 1 minimum low byte
TACH 1 minimum high byte
TACH 2 minimum low byte
TACH 2 minimum high byte
Manufacturer’s Test
These registers are for manufacturer’s use only and should not be read or written to in normal use.
These registers become read only when the Configuration Register 1 lock bit is set to 1. Additional attempts to write to these register have
no effect.
Table 72. Register 0x3F—Manufacturers Test Registers (Power-On Default = 0x00)
Register Address
Read/Write
Read/Write
Read/Write
Read/Write
Read/Write
Description
0x50
0x51
0x52
0x53
Manufacturer’s Test Register 1
Manufacturer’s Test Register 2
Manufacturer’s Test Register 3
Manufacturer’s Test Register 4
Rev. 0 | Page 46 of 48
ADT7466
OUTLINE DIMENSIONS
0.193
BSC
16
1
9
8
0.154
BSC
0.236
BSC
PIN 1
0.069
0.053
0.065
0.049
8°
0°
0.010
0.004
0.025
BSC
0.012
0.008
0.050
0.016
SEATING
PLANE
0.010
0.006
COPLANARITY
0.004
COMPLIANT TO JEDEC STANDARDS MO-137AB
Figure 46. 16-Lead Shrink Small Outline Package [QSOP]
(RQ-16)
Dimensions shown in inches
ORDERING GUIDE
Model
Temperature Range
Package Description
16-Lead QSOP
16-Lead QSOP
16-Lead QSOP
Evaluation Board
Package Option
RQ-16
RQ-16
ADT7466ARQ Z1
ADT7466ARQ Z-REEL1
ADT7466ARQ Z-REEL71
EVAL-ADT7466EB
1 Z = Pb-free part.
−40°C to +125°C
−40°C to +125°C
−40°C to +125°C
RQ-16
Rev. 0 | Page 47 of 48
ADT7466
NOTES
©
2005 Analog Devices, Inc. All rights reserved. Trademarks and
registered trademarks are the property of their respective owners.
D04711–0–6/05(0)
Rev. 0 | Page 48 of 48
相关型号：
EVAL-ADUC-CABLE1Z
MicroConverter® Multichannel 24-/16-Bit ADCs with Embedded 62 kB Flash and Single-Cycle MCU
ADI
©2020 ICPDF网 联系我们和版权申明