CY7C1480V33-250BGC [CYPRESS]
Cache SRAM, 2MX36, 2.6ns, CMOS, PBGA119, 14 X 22 MM, 2.40 MM HEIGHT, PLASTIC, BGA-119;型号: | CY7C1480V33-250BGC |
厂家: | CYPRESS |
描述: | Cache SRAM, 2MX36, 2.6ns, CMOS, PBGA119, 14 X 22 MM, 2.40 MM HEIGHT, PLASTIC, BGA-119 存储 内存集成电路 静态存储器 时钟 |
文件: | 总31页 (文件大小:573K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
CY7C1480V33
CY7C1482V33
CY7C1486V33
72-Mbit (2M x 36/4M x 18/1M x 72)
Pipelined Sync SRAM
Functional Description[1]
Features
• Supports bus operation up to 250 MHz
The CY7C1480V33/CY7C1482V33/CY7C1486V33 SRAM
integrates 2M x 36/4M x 18/1M × 72 SRAM cells with
advanced synchronous peripheral circuitry and a two-bit
• Available speed grades are 250, 200 and 167 MHz
• Registered inputs and outputs for pipelined operation
• 3.3V core power supply
counter for internal burst operation. All synchronous inputs are
gated by registers controlled by a positive-edge-triggered
Clock Input (CLK). The synchronous inputs include all
addresses, all data inputs, address-pipelining Chip Enable
(CE1), depth-expansion Chip Enables (CE2 and CE3), Burst
Control inputs (ADSC, ADSP, and ADV), Write Enables (BWX,
and BWE), and Global Write (GW). Asynchronous inputs
include the Output Enable (OE) and the ZZ pin.
• 2.5V/3.3V I/O operation
• Fast clock-to-output times
— 3.0 ns (for 250-MHz device)
• Provide high-performance 3-1-1-1 access rate
• User-selectable burst counter supporting Intel®
Addresses and chip enables are registered at rising edge of
clock when either Address Strobe Processor (ADSP) or
Address Strobe Controller (ADSC) are active. Subsequent
burst addresses can be internally generated as controlled by
the Advance pin (ADV).
Pentium® interleaved or linear burst sequences
• Separate processor and controller address strobes
• Synchronous self-timed writes
• Asynchronous output enable
Address, data inputs, and write controls are registered on-chip
to initiate a self-timed Write cycle.This part supports Byte Write
operations (see Pin Descriptions and Truth Table for further
details). Write cycles can be one to two or four bytes wide as
controlled by the byte write control inputs. GW when active
• Single Cycle Chip Deselect
• CY7C1480V33, CY7C1482V33 available in
JEDEC-standard lead-free 100-pin TQFP, lead-free and
non-lead-free 165-ball FBGA package. CY7C1486V33
available in lead-free and non-lead-free 209 ball FBGA
package
causes all bytes to be written.
LOW
The CY7C1480V33/CY7C1482V33/CY7C1486V33 operates
from a +3.3V core power supply while all outputs may operate
with either a +2.5 or +3.3V supply. All inputs and outputs are
JEDEC-standard JESD8-5-compatible.
• IEEE 1149.1 JTAG-Compatible Boundary Scan
• “ZZ” Sleep Mode Option
Selection Guide
250 MHz
3.0
200 MHz
3.0
167 MHz
3.4
Unit
ns
Maximum Access Time
Maximum Operating Current
Maximum CMOS Standby Current
500
500
450
mA
mA
120
120
120
Note:
1. For best-practices recommendations, please refer to the Cypress application note System Design Guidelines on www.cypress.com.
Cypress Semiconductor Corporation
Document #: 38-05283 Rev. *G
•
198 Champion Court
•
San Jose, CA 95134-1709
•
408-943-2600
Revised July 24, 2006
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
1
Logic Block Diagram – CY7C1480V33 (2M x 36)
A0, A1, A
ADDRESS
REGISTER
2
A[1:0]
MODE
Q1
ADV
CLK
BURST
COUNTER
AND
CLR
Q0
LOGIC
ADSC
ADSP
DQ
BYTE
WRITE REGISTER
D ,DQPD
DQ
BYTE
WRITE DRIVER
D ,DQPD
BW
D
DQC ,DQP
BYTE
WRITE DRIVER
C
DQC ,DQP
BYTE
WRITE REGISTER
C
BW
C
OUTPUT
BUFFERS
OUTPUT
REGISTERS
MEMORY
ARRAY
DQ s
SENSE
AMPS
DQPA
DQB ,DQP
BYTE
WRITE DRIVER
B
E
DQB ,DQP
BYTE
WRITE REGISTER
B
DQP
DQP
B
C
BW
BW
B
A
DQPD
DQ
BYTE
WRITE DRIVER
A ,DQPA
DQ
A ,DQPA
BYTE
WRITE REGISTER
BWE
INPUT
REGISTERS
GW
ENABLE
REGISTER
PIPELINED
ENABLE
CE
CE
CE
1
2
3
OE
SLEEP
CONTROL
ZZ
2
Logic Block Diagram – CY7C1482V33 (4M x 18)
ADDRESS
A0, A1, A
REGISTER
A[1:0]
2
MODE
Q1
ADV
CLK
BURST
COUNTER AND
LOGIC
CLR
Q0
ADSC
ADSP
DQB,DQP
B
DQB,DQP
WRITE REGISTER
B
WRITE DRIVER
OUTPUT
BUFFERS
BW
B
A
DQs
DQP
DQP
OUTPUT
REGISTERS
SENSE
AMPS
MEMORY
ARRAY
A
B
DQA,DQP
A
E
DQA,DQP
WRITE REGISTER
A
WRITE DRIVER
BW
BWE
GW
INPUT
REGISTERS
ENABLE
REGISTER
CE1
CE2
PIPELINED
ENABLE
CE3
OE
ZZ
SLEEP
CONTROL
Document #: 38-05283 Rev. *G
Page 2 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Logic Block Diagram – CY7C1486V33 (1M x 72)
ADDRESS
REGISTER
A0, A1,A
A[1:0]
MODE
Q1
ADV
CLK
BINARY
COUNTER
CLR
Q0
ADSC
ADSP
DQ
H
, DQP
H
DQ
H, DQPH
BW
BW
H
G
WRITE DRIVER
WRITE DRIVER
DQ
G, DQPG
DQ
F, DQPF
WRITE DRIVER
WRITE DRIVER
DQ
F, DQPF
DQ
F, DQPF
BW
BW
F
E
WRITE DRIVER
WRITE DRIVER
DQ E
E
, DQP
DQ
E, DQPE
WRITE DRIVER
WRITE DRIVER
MEMORY
ARRAY
DQ
D, DQPD
DQ
D, DQPD
BW
D
WRITE DRIVER
WRITE DRIVER
DQ
C, DQPC
DQ
C, DQPC
BW
C
WRITE DRIVER
WRITE DRIVER
OUTPUT
BUFFERS
OUTPUT
REGISTERS
SENSE
AMPS
DQs
DQP
DQP
DQP
DQP
DQP
DQP
DQP
DQP
A
B
C
D
E
E
DQ
B, DQPB
DQ
B, DQPB
WRITE DRIVER
BW
BW
B
A
WRITE DRIVER
DQ
A, DQPA
DQ
A
, DQP
A
F
WRITE DRIVER
WRITE DRIVER
G
H
BWE
INPUT
GW
CE1
CE2
CE3
OE
REGISTERS
ENABLE
REGISTER
PIPELINED
ENABLE
SLEEP
CONTROL
ZZ
Document #: 38-05283 Rev. *G
Page 3 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Pin Configurations
100-pin TQFP Pinout
DQPC
1
DQPB
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQB
DQB
VSSQ
VDDQ
DQB
DQB
VSS
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
NC
NC
NC
VDDQ
VSSQ
NC
A
NC
NC
VDDQ
VSSQ
NC
DQPA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
VSS
NC
1
2
3
4
5
6
7
8
80
79
78
77
76
75
74
73
72
71
70
69
68
67
66
65
64
63
62
61
60
59
58
57
56
55
54
53
52
51
DQC
2
DQc
VDDQ
VSSQ
DQC
3
4
5
6
DQC
7
NC
DQC
8
DQB
DQB
VSSQ
VDDQ
DQB
DQB
NC
VDD
NC
VSS
DQB
DQB
VDDQ
VSSQ
DQB
DQB
DQPB
NC
DQC
9
10
11
9
VSSQ
VDDQ
DQC
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
12
DQC
13
NC
14
VDD
15
NC
VDD
ZZ
CY7C1482V33
(4M x 18)
CY7C1480V33
(2M x 36)
NC
16
VDD
ZZ
VSS
17
DQD
18
DQA
DQA
VDDQ
VSSQ
DQA
DQA
DQA
DQA
VSSQ
VDDQ
DQA
DQA
DQPA
DQA
DQA
VDDQ
VSSQ
DQA
DQA
NC
DQD
19
20
21
VDDQ
VSSQ
DQD
22
DQD
23
DQD
24
DQD
25
26
27
NC
VSSQ
VDDQ
DQD
DQD
29
VSSQ
VDDQ
NC
NC
NC
VSSQ
VDDQ
NC
NC
NC
28
DQPD
30
Document #: 38-05283 Rev. *G
Page 4 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Pin Configurations (continued)
165-ball FBGA (15 x 17 x 1.4 mm) Pinout
CY7C1480V33 (2M x 36)
1
2
3
4
5
6
7
8
9
10
A
11
NC
NC/288M
NC/144M
DQPC
A
B
C
D
CE1
BWC
BWD
VSS
VDD
BWB
BWA
VSS
VSS
CE3
CLK
VSS
VSS
ADSC
A
BWE
GW
VSS
ADV
ADSP
VDDQ
VDDQ
A
CE2
VDDQ
VDDQ
A
NC/576M
DQPB
DQB
OE
VSS
VDD
NC
NC/1G
DQB
DQC
DQC
VSS
DQC
DQC
DQC
DQC
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
DQB
DQB
DQB
NC
DQB
E
F
DQC
DQC
NC
VSS
VSS
VSS
VSS
VSS
VSS
DQB
DQB
ZZ
G
H
J
DQD
DQD
DQD
DQD
DQD
DQD
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
DQA
DQA
DQA
K
L
DQD
DQPD
NC
DQD
NC
A
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
A
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
DQA
DQPA
A
M
N
P
TDI
A1
TDO
A0
MODE
A
A
A
TMS
TCK
A
A
A
A
R
CY7C1482V33 (4M x 18)
1
2
3
4
5
6
7
8
9
10
11
NC/288M
NC/144M
NC
A
NC
A
A
A
BWB
NC
CE
CE1
CE2
BWE
GW
VSS
ADSC
OE
ADV
ADSP
VDDQ
VDDQ
3
A
BWA
VSS
VSS
CLK
VSS
VSS
A
B
C
D
NC/576M
DQPA
DQA
NC
VDDQ
VDDQ
VSS
VDD
VSS
NC/1G
NC
NC
DQB
VSS
VDD
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
NC
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VSS
VDD
VDD
VDD
VDD
VDD
VDD
VDD
VDDQ
VDDQ
VDDQ
NC
NC
NC
DQA
E
F
NC
NC
VSS
VSS
VSS
VSS
VSS
VSS
DQA
DQA
ZZ
NC
G
H
J
NC
NC
DQB
DQB
DQB
NC
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
VDDQ
DQA
DQA
DQA
NC
NC
NC
K
L
NC
NC
DQB
DQPB
NC
NC
NC
A
VDDQ
VDDQ
A
VDD
VSS
A
VSS
NC
VSS
A
VSS
NC
VDD
VSS
A
VDDQ
VDDQ
A
DQA
NC
A
NC
NC
A
M
N
P
TDI
A1
TDO
MODE
A
A
A
TMS
A0
TCK
A
A
A
A
R
Document #: 38-05283 Rev. *G
Page 5 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Pin Configurations (continued)
209-ball FBGA (14 x 22 x 1.76 mm) Pinout
CY7C1486V33 (1M × 72)
1
2
3
4
5
6
7
8
9
10
11
A
B
C
D
E
F
A
DQB
DQB
DQB
DQB
DQB
CE3
BWSB
BWSE
NC
DQG
DQG
DQG
DQG
CE2
ADSC
BWE
DQG
DQG
ADSP
ADV
A
A
NC/288M
NC/144M
BWSC
BWSH
VSS
BWSF
BWSA
VSS
BWSG
BWSD
DQB
DQB
DQB
DQG
DQG
NC/576M
GW
CE1
OE
NC/1G
NC
DQPG DQPC
VDDQ
VDDQ
VDDQ
VSS
VDDQ
VSS
VDDQ
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
VDD
NC
NC
NC
VDD
VSS
VDD
DQPB
DQF
DQPF
DQF
DQC
DQC
DQC
VSS
VDDQ
VSS
VSS
G
H
J
VDDQ
VSS
DQC
DQC
DQC
NC
VDDQ
VSS
DQF
DQF
DQF
VSS
VDD
VSS
VDD
VSS
VDD
VSS
VDD
NC
A
DQC
DQC
NC
DQ
F
VDDQ
VDDQ
VDDQ
CLK
VDDQ
VSS
VDDQ
NC
NC
DQF
NC
DQF
NC
K
L
VSS
NC
NC
DQH
DQH
DQH
VDDQ
VSS
VDDQ
VSS
NC
NC
NC
ZZ
VDDQ
VDDQ
VSS
DQA
DQA
DQ
A
M
N
P
R
T
VSS
VDDQ
VSS
VDDQ
NC
DQH
DQH
DQH
VSS
VDD
VSS
DQA
DQA
DQA
VDDQ
DQH
DQH
DQPD
DQD
DQD
VDDQ
VSS
DQA
DQA
DQPA
DQE
DQE
VSS
VDDQ
VSS
A
VDDQ
VDD
NC
A
DQPH
DQD
DQD
DQD
DQD
VDDQ
VDD
DQPE
DQE
DQE
DQE
DQE
VSS
NC
A
MODE
A
U
V
W
A
A
A
A
A1
A
DQD
DQD
A
A
A
A
DQE
DQE
TDI
TDO
TCK
A0
A
TMS
Document #: 38-05283 Rev. *G
Page 6 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Pin Definitions
Pin Name
I/O
Description
Address Inputs used to select one of the address locations. Sampled at the rising
A0, A1, A
Input-
Synchronous edge of the CLK if ADSP or ADSC is active LOW, and CE1, CE2, and CE3 are sampled
active. A1: A0 are fed to the two-bit counter.
Input-
Byte Write Select Inputs, active LOW. Qualified with BWE to conduct byte writes to
BWA,BWB,BWC,BWD,
BWE,BWF,BWG,BWH
Synchronous the SRAM. Sampled on the rising edge of CLK.
GW
Input- Global Write Enable Input, active LOW. When asserted LOW on the rising edge of
Synchronous CLK, a global write is conducted (ALL bytes are written, regardless of the values on
BWX and BWE).
Input-
Byte Write Enable Input, active LOW. Sampled on the rising edge of CLK. This signal
BWE
CLK
Synchronous must be asserted LOW to conduct a byte write.
Input-
Clock
Clock Input. Used to capture all synchronous inputs to the device. Also used to
increment the burst counter when ADV is asserted LOW, during a burst operation.
Input-
Chip Enable 1 Input, active LOW. Sampled on the rising edge of CLK. Used in
CE1
CE2
Synchronous conjunction with CE2 and CE3 to select/deselect the device. ADSP is ignored if CE1 is
HIGH. CE1 is sampled only when a new external address is loaded.
Input-
Chip Enable 2 Input, active HIGH. Sampled on the rising edge of CLK. Used in
Synchronous conjunction with CE1 and CE3 to select/deselect the device. CE2 is sampled only when
a new external address is loaded.
Input-
Chip Enable 3 Input, active LOW. Sampled on the rising edge of CLK. Used in
CE3
OE
Synchronous conjunction with CE1 and CE2 to select/deselect the device. CE3 is sampled only when
a new external address is loaded.
Input-
Output Enable, asynchronous input, active LOW. Controls the direction of the I/O
Asynchronous pins. When LOW, the I/O pins behave as outputs. When deasserted HIGH, I/O pins are
tri-stated, and act as input data pins. OE is masked during the first clock of a read cycle
when emerging from a deselected state.
ADV
Input-
Advance Input signal, sampled on the rising edge of CLK, active LOW. When
Synchronous asserted, it automatically increments the address in a burst cycle.
ADSP
Input- Address Strobe from Processor, sampled on the rising edge of CLK, active LOW.
Synchronous When asserted LOW, addresses presented to the device are captured in the address
registers. A1: A0 are also loaded into the burst counter. When ADSP and ADSC are
both asserted, only ADSP is recognized. ASDP is ignored when CE1 is deasserted
HIGH.
ADSC
Input-
Address Strobe from Controller, sampled on the rising edge of CLK, active LOW.
Synchronous When asserted LOW, addresses presented to the device are captured in the address
registers. A1: A0 are also loaded into the burst counter. When ADSP and ADSC are
both asserted, only ADSP is recognized.
ZZ
Input-
ZZ “sleep” Input, active HIGH. When asserted HIGH places the device in a
Asynchronous non-time-critical “sleep” condition with data integrity preserved. For normal operation,
this pin has to be LOW or left floating. ZZ pin has an internal pull-down.
I/O-
Synchronous triggered by the rising edge of CLK. As outputs, they deliver the data contained in the
memory location specified by the addresses presented during the previous
Bidirectional Data I/O lines. As inputs, they feed into an on-chip data register that is
DQs, DQPs
clock rise
of the read cycle. The direction of the pins is controlled by OE. When OE is asserted
LOW, the pins behave as outputs. When HIGH, DQs and DQPX are placed in a tri-state
condition.
VDD
Power Supply Power supply inputs to the core of the device.
VSS
Ground
Ground for the core of the device.
VSSQ
VDDQ
I/O Ground Ground for the I/O circuitry.
I/O Power
Supply
Power supply for the I/O circuitry.
Document #: 38-05283 Rev. *G
Page 7 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Pin Definitions (continued)
Pin Name
I/O
Input Static Selects Burst Order. When tied to GND selects linear burst sequence. When tied to
DD or left floating selects interleaved burst sequence. This is a strap pin and should
Description
MODE
V
remain static during device operation. Mode Pin has an internal pull-up.
TDO
TDI
JTAG Serial Serial data-out to the JTAG circuit. Delivers data on the negative edge of TCK. If the
Output
JTAG feature is not being utilized, this pin should be disconnected. This pin is not
Synchronous available on TQFP packages.
JTAG Serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
Input
feature is not being utilized, this pin can be disconnected or connected to VDD. This pin
Synchronous is not available on TQFP packages.
TMS
JTAG Serial Serial data-In to the JTAG circuit. Sampled on the rising edge of TCK. If the JTAG
Input
feature is not being utilized, this pin can be disconnected or connected to VDD. This pin
Synchronous is not available on TQFP packages.
TCK
NC
JTAG Clock Clock input to the JTAG circuitry. If the JTAG feature is not being utilized, this pin
must be connected to VSS. This pin is not available on TQFP packages.
-
No Connects. Not internally connected to the die. 144M,288M, 576M and 1G are
address expansion pins and are not internally connected to the die.
data is allowed to propagate through the output register and
onto the data bus within 3.0 ns (250-MHz device) if OE is
Functional Overview
All synchronous inputs pass through input registers controlled
by the rising edge of the clock. All data outputs pass through
output registers controlled by the rising edge of the clock.
Maximum access delay from the clock rise (tCO) is 3.0 ns
(250-MHz device).
active LOW. The only exception occurs when the SRAM is
emerging from a deselected state to a selected state, its
outputs are always tri-stated during the first cycle of the
access. After the first cycle of the access, the outputs are
controlled by the OE signal. Consecutive single Read cycles
are supported. Once the SRAM is deselected at clock rise by
the chip select and either ADSP or ADSC signals, its output
will tri-state immediately.
The CY7C1480V33/CY7C1482V33/CY7C1486V33 supports
secondary cache in systems utilizing either a linear or inter-
leaved burst sequence. The interleaved burst order supports
Pentium and i486™ processors. The linear burst sequence is
suited for processors that utilize a linear burst sequence. The
burst order is user selectable, and is determined by sampling
the MODE input. Accesses can be initiated with either the
Processor Address Strobe (ADSP) or the Controller Address
Strobe (ADSC). Address advancement through the burst
sequence is controlled by the ADV input. A two-bit on-chip
wraparound burst counter captures the first address in a burst
sequence and automatically increments the address for the
rest of the burst access.
Single Write Accesses Initiated by ADSP
This access is initiated when both of the following conditions
are satisfied at clock rise: (1) ADSP is asserted LOW, and
(2) CE1, CE2, CE3 are all asserted active. The address
presented to A is loaded into the address register and the
address advancement logic while being delivered to the
memory array. The Write signals (GW, BWE, and BWX) and
ADV inputs are ignored during this first cycle.
ADSP-triggered Write accesses require two clock cycles to
complete. If GW is asserted LOW on the second clock rise, the
data presented to the DQs inputs is written into the corre-
sponding address location in the memory array. If GW is HIGH,
then the Write operation is controlled by BWE and BWX
signals.
Byte Write operations are qualified with the Byte Write Enable
(BWE) and Byte Write Select (BWX) inputs. A Global Write
Enable (GW) overrides all Byte Write inputs and writes data to
all four bytes. All writes are simplified with on-chip
synchronous self-timed Write circuitry.
Three synchronous Chip Selects (CE1, CE2, CE3) and an
asynchronous Output Enable (OE) provide for easy bank
selection and output tri-state control. ADSP is ignored if CE1
is HIGH.
The CY7C1480V33/CY7C1482V33/CY7C1486V33 provides
Byte Write capability that is described in the Write Cycle
Descriptions table. Asserting the Byte Write Enable input
(BWE) with the selected Byte Write (BWX) input, will selec-
tively write to only the desired bytes. Bytes not selected during
a Byte Write operation will remain unaltered. A synchronous
self-timed Write mechanism has been provided to simplify the
Write operations.
Single Read Accesses
This access is initiated when the following conditions are
satisfied at clock rise: (1) ADSP or ADSC is asserted LOW, (2)
CE1, CE2, CE3 are all asserted active, and (3) the Write
signals (GW, BWE) are all deasserted HIGH. ADSP is ignored
if CE1 is HIGH. The address presented to the address inputs
(A) is stored into the address advancement logic and the
Address Register while being presented to the memory array.
The corresponding data is allowed to propagate to the input of
the Output Registers. At the rising edge of the next clock the
Because CY7C1480V33/CY7C1482V33/CY7C1486V33 is a
common I/O device, the Output Enable (OE) must be
deasserted HIGH before presenting data to the DQs inputs.
Doing so will tri-state the output drivers. As a safety
precaution, DQs are automatically tri-stated whenever a Write
cycle is detected, regardless of the state of OE.
Document #: 38-05283 Rev. *G
Page 8 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Single Write Accesses Initiated by ADSC
Sleep Mode
ADSC Write accesses are initiated when the following condi-
tions are satisfied: (1) ADSC is asserted LOW, (2) ADSP is
deasserted HIGH, (3) CE1, CE2, CE3 are all asserted active,
and (4) the appropriate combination of the Write inputs (GW,
BWE, and BWX) are asserted active to conduct a Write to the
desired byte(s). ADSC-triggered Write accesses require a
single clock cycle to complete. The address presented to A is
loaded into the address register and the address
advancement logic while being delivered to the memory array.
The ADV input is ignored during this cycle. If a global Write is
conducted, the data presented to the DQs is written into the
corresponding address location in the memory core. If a Byte
Write is conducted, only the selected bytes are written. Bytes
not selected during a Byte Write operation will remain
unaltered. A synchronous self-timed Write mechanism has
been provided to simplify the Write operations.
The ZZ input pin is an asynchronous input. Asserting ZZ
places the SRAM in a power conservation “sleep” mode. Two
clock cycles are required to enter into or exit from this “sleep”
mode. While in this mode, data integrity is guaranteed.
Accesses pending when entering the “sleep” mode are not
considered valid nor is the completion of the operation
guaranteed. The device must be deselected prior to entering
the “sleep” mode. CE1, CE2, CE3, ADSP, and ADSC must
remain inactive for the duration of tZZREC after the ZZ input
returns LOW.
Interleaved Burst Address Table
(MODE = Floating or VDD
)
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
Because CY7C1480V33/CY7C1482V33/CY7C1486V33 is a
common I/O device, the Output Enable (OE) must be
deasserted HIGH before presenting data to the DQs inputs.
Doing so will tri-state the output drivers. As a safety
precaution, DQs are automatically tri-stated whenever a Write
cycle is detected, regardless of the state of OE.
00
01
10
11
01
00
11
10
10
11
00
01
11
10
01
00
Burst Sequences
Linear Burst Address Table
(MODE = GND)
The CY7C1480V33/CY7C1482V33/CY7C1486V33 provides
a two-bit wraparound counter, fed by A1: A0, that implements
either an interleaved or linear burst sequence. The interleaved
burst sequence is designed specifically to support Intel
Pentium applications. The linear burst sequence is designed
to support processors that follow a linear burst sequence. The
burst sequence is user selectable through the MODE input.
First
Address
A1: A0
Second
Address
A1: A0
Third
Address
A1: A0
Fourth
Address
A1: A0
00
01
10
11
01
10
11
00
10
11
00
01
11
00
01
10
Asserting ADV LOW at clock rise will automatically increment
the burst counter to the next address in the burst sequence.
Both Read and Write burst operations are supported.
ZZ Mode Electrical Characteristics
Parameter
IDDZZ
Description
Sleep mode standby current
Device operation to ZZ
Test Conditions
ZZ > VDD – 0.2V
Min.
Max.
Unit
mA
ns
120
tZZS
ZZ > VDD – 0.2V
2tCYC
tZZREC
tZZI
ZZ recovery time
ZZ < 0.2V
2tCYC
0
ns
ZZ Active to Sleep current
ZZ Inactive to exit Sleep current
This parameter is sampled
This parameter is sampled
2tCYC
ns
tRZZI
ns
Document #: 38-05283 Rev. *G
Page 9 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Truth Table[2, 3, 4, 5, 6]
Operation
Add. Used CE1 CE2 CE3 ZZ ADSP ADSC ADV WRITE OE CLK
DQ
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Deselect Cycle, Power Down
Sleep Mode, Power Down
READ Cycle, Begin Burst
READ Cycle, Begin Burst
WRITE Cycle, Begin Burst
READ Cycle, Begin Burst
READ Cycle, Begin Burst
READ Cycle, Continue Burst
READ Cycle, Continue Burst
READ Cycle, Continue Burst
READ Cycle, Continue Burst
WRITE Cycle, Continue Burst
WRITE Cycle, Continue Burst
READ Cycle, Suspend Burst
READ Cycle, Suspend Burst
READ Cycle, Suspend Burst
READ Cycle, Suspend Burst
WRITE Cycle,Suspend Burst
WRITE Cycle,Suspend Burst
None
None
H
L
X
L
X
X
H
X
H
X
L
L
L
L
L
L
H
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
L
X
L
L
X
X
L
X
X
X
X
X
X
X
X
X
X
X
L
X
X
X
X
X
X
X
X
L
X
X
X
X
X
X
L
L-H Tri-State
L-H Tri-State
L-H Tri-State
L-H Tri-State
L-H Tri-State
None
L
X
L
L
None
L
H
H
X
L
None
L
X
X
H
H
H
H
H
X
X
X
X
X
X
X
X
X
X
X
X
L
None
X
L
X
X
X
L
X
Tri-State
Q
External
External
External
External
External
Next
L-H
L
L
L
H
X
L
L-H Tri-State
L
L
H
H
H
H
H
X
X
H
X
H
H
X
X
H
X
L-H
L-H
D
Q
L
L
L
H
H
H
H
H
H
L
L
L
L
H
L
L-H Tri-State
L-H
L-H Tri-State
L-H
L-H Tri-State
X
X
H
H
X
H
X
X
H
H
X
H
X
X
X
X
X
X
X
X
X
X
X
X
H
H
H
H
H
H
H
H
H
H
H
H
Q
Next
L
H
L
Next
L
Q
Next
L
H
X
X
L
Next
L
L-H
L-H
L-H
D
D
Q
Next
L
L
Current
Current
Current
Current
Current
Current
H
H
H
H
H
H
H
H
H
H
L
H
L
L-H Tri-State
L-H
L-H Tri-State
Q
H
X
X
L-H
L-H
D
D
L
Notes:
2. X = “Don't Care.” H = Logic HIGH, L = Logic LOW.
3. WRITE = L when any one or more Byte Write enable signals and BWE = L or GW = L. WRITE = H when all Byte write enable signals, BWE, GW = H.
4. The DQ pins are controlled by the current cycle and the signal. is asynchronous and is not sampled with the clock.
OE
OE
5. The SRAM always initiates a read cycle when ADSP is asserted, regardless of the state of GW, BWE, or BW . Writes may occur only on subsequent clocks
X
after the ADSP or with the assertion of ADSC. As a result, OE must be driven HIGH prior to the start of the write cycle to allow the outputs to tri-state. OE is a
don't care for the remainder of the write cycle.
6. OE is asynchronous and is not sampled with the clock rise. It is masked internally during write cycles. During a read cycle all data bits are Tri-State when OE is
inactive or when the device is deselected, and all data bits behave as output when OE is active (LOW).
Document #: 38-05283 Rev. *G
Page 10 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Truth Table for Read/Write[4]
Function (CY7C1480V33)
Read
GW
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
H
L
BWE
H
L
BWD
X
H
H
H
H
H
H
H
H
L
BWC
X
H
H
H
H
L
BWB
X
H
H
L
BWA
X
H
L
Read
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
Write Bytes B, A
L
L
H
L
L
L
Write Byte C – (DQC and DQPC)
Write Bytes C, A
L
H
H
L
H
L
L
L
Write Bytes C, B
L
L
H
L
Write Bytes C, B, A
Write Byte D – (DQD and DQPD)
Write Bytes D, A
L
L
L
L
H
H
H
H
L
H
H
L
H
L
L
L
Write Bytes D, B
L
L
H
L
Write Bytes D, B, A
Write Bytes D, C
L
L
L
L
L
H
H
L
H
L
Write Bytes D, C, A
Write Bytes D, C, B
Write All Bytes
L
L
L
L
L
L
H
L
L
L
L
L
Write All Bytes
X
X
X
X
X
Truth Table for Read/Write[4]
Function (CY7C1482V33)
Read
GW
H
BWE
BWB
X
BWA
H
L
L
L
L
L
X
X
H
L
Read
H
H
Write Byte A – (DQA and DQPA)
Write Byte B – (DQB and DQPB)
Write Bytes B, A
H
H
H
L
H
L
H
L
Write All Bytes
H
L
L
Write All Bytes
L
X
X
Truth Table for Read/Write[7]
Function (CY7C1486V33)
GW
H
BWE
BWX
Read
H
L
L
L
X
X
Read
H
All BW = H
Write Byte x – (DQx and DQPx)
Write All Bytes
H
L
All BW = L
X
H
Write All Bytes
L
Note:
7. BWx represents any byte write signal BW[0..7].To enable any byte write BWx, a Logic LOW signal should be applied at clock rise.Any number of bye writes can
be enabled at the same time for any given write.
Document #: 38-05283 Rev. *G
Page 11 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Test MODE SELECT (TMS)
IEEE 1149.1 Serial Boundary Scan (JTAG)
The TMS input is used to give commands to the TAP controller
and is sampled on the rising edge of TCK. It is allowable to
leave this ball unconnected if the TAP is not used. The ball is
pulled up internally, resulting in a logic HIGH level.
The CY7C1480V33/CY7C1482V33/CY7C1486V33 incorpo-
rates a serial boundary scan test access port (TAP). This port
operates in accordance with IEEE Standard 1149.1-1990 but
does not have the set of functions required for full 1149.1
compliance. These functions from the IEEE specification are
excluded because their inclusion places an added delay in the
critical speed path of the SRAM. Note that the TAP controller
functions in a manner that does not conflict with the operation
of other devices using 1149.1 fully compliant TAPs. The TAP
operates using JEDEC-standard 3.3V or 2.5V I/O logic levels.
Test Data-In (TDI)
The TDI ball is used to serially input information into the
registers and can be connected to the input of any of the
registers. The register between TDI and TDO is chosen by the
instruction that is loaded into the TAP instruction register. For
information on loading the instruction register, see the TAP
Controller State Diagram. TDI is internally pulled up and can
be unconnected if the TAP is unused in an application. TDI is
connected to the most significant bit (MSB) of any register.
(See Tap Controller Block Diagram.)
The CY7C1480V33/CY7C1482V33/CY7C1486V33 contains
a TAP controller, instruction register, boundary scan register,
bypass register, and ID register.
Disabling the JTAG Feature
Test Data-Out (TDO)
It is possible to operate the SRAM without using the JTAG
feature. To disable the TAP controller, TCK must be tied LOW
(VSS) to prevent clocking of the device. TDI and TMS are inter-
nally pulled up and may be unconnected. They may alternately
be connected to VDD through a pull-up resistor. TDO should be
left unconnected. Upon power-up, the device will come up in
a reset state which will not interfere with the operation of the
device.
The TDO output ball is used to serially clock data-out from the
registers. The output is active depending upon the current
state of the TAP state machine. The output changes on the
falling edge of TCK. TDO is connected to the least significant
bit (LSB) of any register. (See Tap Controller State Diagram.)
TAP Controller Block Diagram
TAP Controller State Diagram
0
Bypass Register
TEST-LOGIC
1
RESET
0
2
1
0
0
0
1
1
1
Selection
Circuitry
RUN-TEST/
IDLE
SELECT
DR-SCAN
SELECT
IR-SCAN
Instruction Register
31 30 29
Identification Register
0
S
election
TDI
TDO
Circuitr
y
0
0
.
.
. 2 1
1
1
CAPTURE-DR
CAPTURE-IR
0
0
x
.
.
.
.
. 2 1
SHIFT-DR
0
SHIFT-IR
0
Boundary Scan Register
1
1
1
1
EXIT1-DR
EXIT1-IR
TCK
TMS
0
0
TAP CONTROLLER
PAUSE-DR
0
PAUSE-IR
0
1
1
0
0
EXIT2-DR
1
EXIT2-IR
1
Performing a TAP Reset
A RESET is performed by forcing TMS HIGH (VDD) for five
rising edges of TCK. This RESET does not affect the operation
of the SRAM and may be performed while the SRAM is
operating.
UPDATE-DR
UPDATE-IR
1
0
1
0
At power-up, the TAP is reset internally to ensure that TDO
comes up in a High-Z state.
The 0/1 next to each state represents the value of TMS at the
rising edge of TCK.
TAP Registers
Test Access Port (TAP)
Registers are connected between the TDI and TDO balls and
allow data to be scanned into and out of the SRAM test
circuitry. Only one register can be selected at a time through
the instruction register. Data is serially loaded into the TDI ball
on the rising edge of TCK. Data is output on the TDO ball on
the falling edge of TCK.
Test Clock (TCK)
The test clock is used only with the TAP controller. All inputs
are captured on the rising edge of TCK. All outputs are driven
from the falling edge of TCK.
Document #: 38-05283 Rev. *G
Page 12 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Instruction Register
Instructions are loaded into the TAP controller during the
Shift-IR state when the instruction register is placed between
TDI and TDO. During this state, instructions are shifted
through the instruction register through the TDI and TDO balls.
To execute the instruction once it is shifted in, the TAP
controller needs to be moved into the Update-IR state.
Three-bit instructions can be serially loaded into the instruction
register. This register is loaded when it is placed between the
TDI and TDO balls as shown in the Tap Controller Block
Diagram. Upon power-up, the instruction register is loaded
with the IDCODE instruction. It is also loaded with the IDCODE
instruction if the controller is placed in a reset state as
described in the previous section.
EXTEST
EXTEST is a mandatory 1149.1 instruction which is to be
executed whenever the instruction register is loaded with all
0s. EXTEST is not implemented in this SRAM TAP controller,
and therefore this device is not compliant to 1149.1. The TAP
controller does recognize an all-0 instruction.
When the TAP controller is in the Capture-IR state, the two
least significant bits are loaded with a binary “01” pattern to
allow for fault isolation of the board-level serial test data path.
Bypass Register
When an EXTEST instruction is loaded into the instruction
register, the SRAM responds as if a SAMPLE/PRELOAD
instruction has been loaded. There is one difference between
the two instructions. Unlike the SAMPLE/PRELOAD
instruction, EXTEST places the SRAM outputs in a High-Z
state.
To save time when serially shifting data through registers, it is
sometimes advantageous to skip certain chips. The bypass
register is a single-bit register that can be placed between the
TDI and TDO balls. This allows data to be shifted through the
SRAM with minimal delay. The bypass register is set LOW
(VSS) when the BYPASS instruction is executed.
IDCODE
Boundary Scan Register
The IDCODE instruction causes a vendor-specific, 32-bit code
to be loaded into the instruction register. It also places the
instruction register between the TDI and TDO balls and allows
the IDCODE to be shifted out of the device when the TAP
controller enters the Shift-DR state.
The boundary scan register is connected to all the input and
bidirectional balls on the SRAM. The x36 configuration has a
73-bit-long register, and the x18 configuration has
54-bit-long register.
a
The boundary scan register is loaded with the contents of the
RAM I/O ring when the TAP controller is in the Capture-DR
state and is then placed between the TDI and TDO balls when
the controller is moved to the Shift-DR state. The EXTEST,
SAMPLE/PRELOAD and SAMPLE Z instructions can be used
to capture the contents of the I/O ring.
The IDCODE instruction is loaded into the instruction register
upon power-up or whenever the TAP controller is given a test
logic reset state.
SAMPLE Z
The SAMPLE Z instruction causes the boundary scan register
to be connected between the TDI and TDO balls when the TAP
controller is in a Shift-DR state. It also places all SRAM outputs
into a High-Z state.
The Boundary Scan Order tables show the order in which the
bits are connected. Each bit corresponds to one of the bumps
on the SRAM package. The MSB of the register is connected
to TDI and the LSB is connected to TDO.
SAMPLE/PRELOAD
Identification (ID) Register
SAMPLE/PRELOAD is a 1149.1 mandatory instruction. The
PRELOAD portion of this instruction is not implemented, so
the device TAP controller is not fully 1149.1 compliant.
The ID register is loaded with a vendor-specific, 32-bit code
during the Capture-DR state when the IDCODE command is
loaded in the instruction register. The IDCODE is hardwired
into the SRAM and can be shifted out when the TAP controller
is in the Shift-DR state. The ID register has a vendor code and
other information described in the Identification Register
Definitions table.
When the SAMPLE/PRELOAD instruction is loaded into the
instruction register and the TAP controller is in the Capture-DR
state, a snapshot of data on the inputs and bidirectional balls
is captured in the boundary scan register.
The user must be aware that the TAP controller clock can only
operate at a frequency up to 10 MHz, while the SRAM clock
operates more than an order of magnitude faster. Because
there is a large difference in the clock frequencies, it is
possible that during the Capture-DR state, an input or output
will undergo a transition. The TAP may then try to capture a
signal while in transition (metastable state). This will not harm
the device, but there is no guarantee as to the value that will
be captured. Repeatable results may not be possible.
TAP Instruction Set
Overview
Eight different instructions are possible with the three-bit
instruction register. All combinations are listed in the
Instruction Codes table. Three of these instructions are listed
as RESERVED and should not be used. The other five instruc-
tions are described in detail below.
The TAP controller used in this SRAM is not fully compliant to
the 1149.1 convention because some of the mandatory 1149.1
instructions are not fully implemented.
To guarantee that the boundary scan register will capture the
correct value of a signal, the SRAM signal must be stabilized
long enough to meet the TAP controller’s capture set-up plus
hold time (tCS plus tCH).
The TAP controller cannot be used to load address data or
control signals into the SRAM and cannot preload the I/O
buffers. The SRAM does not implement the 1149.1 commands
EXTEST or INTEST or the PRELOAD portion of
SAMPLE/PRELOAD; rather, it performs a capture of the I/O
ring when these instructions are executed.
The SRAM clock input might not be captured correctly if there
is no way in a design to stop (or slow) the clock during a
SAMPLE/PRELOAD instruction. If this is an issue, it is still
Document #: 38-05283 Rev. *G
Page 13 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
possible to capture all other signals and simply ignore the
value of the CLK captured in the boundary scan register.
BYPASS
When the BYPASS instruction is loaded in the instruction
register and the TAP is placed in a Shift-DR state, the bypass
register is placed between the TDI and TDO balls. The
advantage of the BYPASS instruction is that it shortens the
boundary scan path when multiple devices are connected
together on a board.
Once the data is captured, it is possible to shift out the data by
putting the TAP into the Shift-DR state. This places the
boundary scan register between the TDI and TDO balls.
Note that since the PRELOAD part of the command is not
implemented, putting the TAP to the Update-DR state while
performing a SAMPLE/PRELOAD instruction will have the
same effect as the Pause-DR command.
Reserved
These instructions are not implemented but are reserved for
future use. Do not use these instructions.
TAP Timing
1
2
3
4
5
6
Test Clock
(TCK)
t
t
t
CYC
TH
TL
t
t
t
t
TMSS
TDIS
TMSH
Test Mode Select
(TMS)
TDIH
Test Data-In
(TDI)
t
TDOV
t
TDOX
Test Data-Out
(TDO)
DON’T CARE
UNDEFINED
TAP AC Switching Characteristics Over the Operating Range[8, 9]
Parameter
Clock
tTCYC
tTF
Description
Min.
Max.
Unit
TCK Clock Cycle Time
TCK Clock Frequency
TCK Clock HIGH time
TCK Clock LOW time
50
ns
MHz
ns
20
tTH
20
20
tTL
ns
Output Times
tTDOV TCK Clock LOW to TDO Valid
tTDOX TCK Clock LOW to TDO Invalid
Set-up Times
tTMSS TMS Set-up to TCK Clock Rise
tTDIS
10
ns
ns
0
5
5
5
ns
ns
ns
TDI Set-up to TCK Clock Rise
Capture Set-up to TCK Rise
tCS
Hold Times
tTMSH
tTDIH
TMS Hold after TCK Clock Rise
TDI Hold after Clock Rise
5
5
5
ns
ns
ns
tCH
Capture Hold after Clock Rise
Notes:
8. t and t refer to the set-up and hold time requirements of latching data from the boundary scan register.
CS
CH
9. Test conditions are specified using the load in TAP AC Test Conditions. t /t = 1 ns.
R
F
Document #: 38-05283 Rev. *G
Page 14 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
3.3V TAP AC Test Conditions
2.5V TAP AC Test Conditions
Input pulse levels ............................................... .VSS to 3.3V
Input rise and fall times................................................... 1 ns
Input timing reference levels...........................................1.5V
Output reference levels...................................................1.5V
Test load termination supply voltage...............................1.5V
Input pulse levels.................................................VSS to 2.5V
Input rise and fall time .....................................................1 ns
Input timing reference levels......................................... 1.25V
Output reference levels ................................................ 1.25V
Test load termination supply voltage ............................ 1.25V
3.3V TAP AC Output Load Equivalent
2.5V TAP AC Output Load Equivalent
1.5V
1.25V
50Ω
50Ω
TDO
TDO
ZO= 50Ω
ZO= 50Ω
20pF
20pF
TAP DC Electrical Characteristics And Operating Conditions
(0°C < TA < +70°C; VDD = 3.135 to 3.6V unless otherwise noted)[10]
Parameter
VOH1
Description
Output HIGH Voltage IOH = –4.0 mA, VDDQ = 3.3V
OH = –1.0 mA, VDDQ = 2.5V
Test Conditions
Min.
2.4
2.0
2.9
2.1
Max.
Unit
V
I
V
VOH2
VOL1
VOL2
VIH
Output HIGH Voltage IOH = –100 µA
VDDQ = 3.3V
DDQ = 2.5V
V
V
V
Output LOW Voltage IOL = 8.0 mA
IOL = 1.0 mA
VDDQ = 3.3V
VDDQ = 2.5V
VDDQ = 3.3V
0.4
0.4
V
V
Output LOW Voltage IOL = 100 µA
0.2
V
V
DDQ = 2.5V
VDDQ = 3.3V
DDQ = 2.5V
0.2
V
Input HIGH Voltage
Input LOW Voltage
2.0
1.7
VDD + 0.3
VDD + 0.3
0.8
V
V
V
VIL
VDDQ = 3.3V
VDDQ = 2.5V
–0.3
–0.3
–5
V
0.7
V
IX
Input Load Current
GND < VIN < VDDQ
5
µA
Identification Register Definitions
CY7C1480V33 CY7C1482V33 CY7C1486V33
Instruction Field
Revision Number (31:29)
Device Depth (28:24)
(2M x36)
(4M x 18)
(1M x72)
Description
000
000
000
Describes the version number
Reserved for internal use
01011
01011
01011
Architecture/Memory Type(23:18)
Bus Width/Density(17:12)
Cypress JEDEC ID Code (11:1)
000000
100100
000000
010100
000000
110100
Defines memory type and architecture
Defines width and density
00000110100 00000110100 00000110100 Allows unique identification of SRAM
vendor
ID Register Presence Indicator (0)
1
1
1
Indicates the presence of an ID register
Notes:
10. All voltages referenced to V (GND).
SS
11. Bit #24 is “1” in the ID Register Definitions for both 2.5V and 3.3V versions of this device.
Document #: 38-05283 Rev. *G
Page 15 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Scan Register Sizes
Register Name
Bit Size (x36)
Bit Size (x18)
Bit Size (x72)
Instruction
3
1
3
1
3
1
Bypass
ID
32
73
-
32
54
-
32
-
Boundary Scan Order-165FBGA
Boundary Scan Order-209BGA
112
Identification Codes
Instruction
EXTEST
Code
000
Description
Captures the I/O ring contents.
IDCODE
001
Loads the ID register with the vendor ID code and places the register between TDI and
TDO. This operation does not affect SRAM operations.
SAMPLE Z
010
Captures I/O ring contents. Places the boundary scan register between TDI and TDO.
Forces all SRAM output drivers to a High-Z state.
RESERVED
011
100
Do Not Use: This instruction is reserved for future use.
SAMPLE/PRELOAD
Captures I/O ring contents. Places the boundary scan register between TDI and TDO.
Does not affect SRAM operation.
RESERVED
RESERVED
BYPASS
101
110
111
Do Not Use: This instruction is reserved for future use.
Do Not Use: This instruction is reserved for future use.
Places the bypass register between TDI and TDO. This operation does not affect SRAM
operations.
Boundary Scan Exit Order (2M x 36)
Bit #
1
165-Ball ID
C1
Bit #
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
165-Ball ID
R3
Bit #
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
165-Ball ID
L10
K11
J11
Bit #
61
62
63
64
65
66
67
68
69
70
71
72
73
165-Ball ID
B8
A7
B7
B6
A6
B5
A5
A4
B4
B3
A3
A2
B2
2
D1
P2
3
E1
R4
4
D2
P6
K10
J10
5
E2
R6
6
F1
N6
H11
G11
F11
7
G1
F2
P11
R8
8
9
G2
J1
P3
E11
D10
D11
C11
G10
F10
E10
A10
B10
A9
10
11
12
13
14
15
16
17
18
19
20
P4
K1
P8
L1
P9
J2
P10
R9
M1
N1
R10
R11
N11
M11
L11
M10
K2
L2
M2
R1
B9
R2
A8
Document #: 38-05283 Rev. *G
Page 16 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Boundary Scan Exit Order (4M x 18)
Bit #
1
165-Ball ID
D2
Bit #
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
165-Ball ID
R8
Bit #
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
165-Ball ID
C11
A11
A10
B10
A9
2
E2
P3
3
F2
P4
4
G2
P8
5
J1
P9
6
K1
P10
R9
B9
7
L1
A8
8
M1
N1
R10
R11
M10
L10
K10
J10
H11
G11
F11
E11
D11
B8
9
A7
10
11
12
13
14
15
16
17
18
R1
B7
R2
B6
R3
A6
P2
B5
R4
A4
P6
B3
R6
A3
N6
A2
P11
B2
Document #: 38-05283 Rev. *G
Page 17 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Boundary Scan Exit Order (1M x 72)
Bit #
1
209-Ball ID
A1
Bit #
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
209-Ball ID
T1
Bit #
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
209-Ball ID
V10
U11
U10
T11
Bit #
85
209-Ball ID
C11
C10
B11
B10
A11
A10
A9
2
A2
T2
86
3
B1
U1
87
4
B2
U2
88
5
C1
C2
D1
D2
E1
V1
T10
R11
R10
P11
P10
N11
N10
M11
M10
L11
89
6
V2
90
7
W1
W2
T6
91
8
92
U8
9
93
A7
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
E2
V3
94
A5
F1
V4
95
A6
F2
U4
96
D6
G1
G2
H1
H2
J1
W5
V6
97
B6
98
D7
W6
U3
L10
99
K3
P6
100
101
102
103
104
105
106
107
108
109
110
111
112
A8
U9
J11
B4
J2
V5
J10
B3
L1
U5
H11
H10
G11
G10
F11
C3
L2
U6
C4
M1
M2
N1
N2
P1
W7
V7
C8
C9
U7
B9
V8
F10
E10
E11
D11
D10
B8
V9
A4
P2
W11
W10
V11
C6
R2
R1
B7
A3
Document #: 38-05283 Rev. *G
Page 18 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
DC Input Voltage ................................... –0.5V to VDD + 0.5V
Current into Outputs (LOW)......................................... 20mA
Maximum Ratings
(Above which the useful life may be impaired. For user guide-
lines, not tested.)
Static Discharge Voltage........................................... >2001V
(per MIL-STD-883, Method 3015Latch-up Current. >200 mA
Storage Temperature .................................–65°C to +150°C
Operating Range
Ambient Temperature with
Power Applied.............................................–55°C to +125°C
Ambient
Temperature
Range
VDD
VDDQ
Supply Voltage on VDD Relative to GND........ –0.3V to +4.6V
Supply Voltage on VDDQ Relative to GND ......–0.3V to +VDD
Commercial 0°C to +70°C 3.3V –5%/+10% 2.5V – 5%
to VDD
Industrial
–40°C to +85°C
DC Voltage Applied to Outputs
in Tri-State........................................... –0.5V to VDDQ + 0.5V
Electrical Characteristics Over the Operating Range[12, 13]
Parameter
VDD
Description
Power Supply Voltage
I/O Supply Voltage
Test Conditions
Min.
3.135
3.135
2.375
2.4
Max.
3.6
Unit
V
VDDQ
for 3.3V I/O
for 2.5V I/O
VDD
V
2.625
V
VOH
VOL
VIH
VIL
IX
Output HIGH Voltage
Output LOW Voltage
for 3.3V I/O, IOH = –4.0 mA
for 2.5V I/O, IOH = –1.0 mA
for 3.3V I/O, IOL = 8.0 mA
for 2.5V I/O, IOL = 1.0 mA
V
2.0
V
0.4
0.4
V
V
Input HIGH Voltage[12] for 3.3V I/O
2.0
1.7
VDD + 0.3V
V
for 2.5V I/O
V
DD + 0.3V
V
Input LOW Voltage[12]
for 3.3V I/O
for 2.5V I/O
–0.3
–0.3
–5
0.8
0.7
5
V
V
Input Leakage Current GND ≤ VI ≤ VDDQ
except ZZ and MODE
µA
Input Current of MODE Input = VSS
Input = VDD
–30
–5
µA
µA
5
Input Current of ZZ
Input = VSS
Input = VDD
µA
30
5
µA
IOZ
IDD
Output Leakage Current GND ≤ VI ≤ VDDQ, Output Disabled
–5
µA
VDD Operating Supply VDD = Max., IOUT = 0 mA,
4.0-ns cycle, 250 MHz
5.0-ns cycle, 200 MHz
6.0-ns cycle, 167 MHz
500
500
450
245
245
245
120
mA
mA
mA
mA
mA
mA
mA
Current
f = fMAX = 1/tCYC
ISB1
Automatic CE
Power-down
Current—TTL Inputs
VDD = Max, Device Deselected, 4.0-ns cycle, 250 MHz
VIN ≥ VIH or VIN ≤ VIL
f = fMAX = 1/tCYC
5.0-ns cycle, 200 MHz
6.0-ns cycle, 167 MHz
ISB2
Automatic CE
Power-down
Current—CMOS Inputs f = 0
VDD = Max, Device Deselected, All speeds
VIN ≤ 0.3V or VIN > VDDQ – 0.3V,
ISB3
Automatic CE
Power-down
Current—CMOS Inputs f = fMAX = 1/tCYC
VDD = Max, Device Deselected, or 4.0-ns cycle, 250 MHz
245
245
245
135
mA
mA
mA
mA
VIN ≤ 0.3V or VIN > VDDQ – 0.3V
5.0-ns cycle, 200 MHz
6.0-ns cycle, 167 MHz
ISB4
Automatic CE
Power-down
Current—TTL Inputs
VDD = Max, Device Deselected, All speeds
VIN ≥ VIH or VIN ≤ VIL, f = 0
Notes:
12. Overshoot: V (AC) < V +1.5V (Pulse width less than t
/2), undershoot: V (AC) > –2V (Pulse width less than t
/2).
IH
DD
CYC
IL
CYC
< V
DD.
13. Power-up: Assumes a linear ramp from 0V to V (min.) within 200 ms. During this time V < V and V
DD
IH
DD
DDQ
Document #: 38-05283 Rev. *G
Page 19 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Capacitance[14]
100 TQFP 165 FBGA 209 FBGA
Parameter
Description
Test Conditions
Max.
Max.
Max.
Unit
pF
CADDRESS
CDATA
CCTRL
CCLK
Address Input Capacitance
Data Input Capacitance
Control Input Capacitance
Clock Input Capacitance
Input/Output Capacitance
TA = 25°C, f = 1 MHz,
6
5
8
6
5
6
5
8
6
5
6
5
8
6
5
VDD = 3.3V
pF
VDDQ = 2.5V
pF
pF
CI/O
pF
Thermal Resistance[14]]
100 TQFP
Package
165 FBGA 209 FBGA
Parameter
Description
Test Conditions
Package
Package
Unit
ΘJA
Thermal Resistance
(Junction to Ambient)
Test conditions follow
standard test methods and
procedures for measuring
thermal impedance, per
EIA/JESD51.
24.63
16.3
15.2
°C/W
ΘJC
Thermal Resistance
(Junction to Case)
2.28
2.1
1.7
°C/W
AC Test Loads and Waveforms
3.3V I/O Test Load
R = 317Ω
3.3V
OUTPUT
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
R = 50Ω
10%
L
5 pF
R = 351Ω
≤ 1 ns
≤ 1 ns
V = 1.5V
L
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
2.5V I/O Test Load
R = 1667Ω
2.5V
OUTPUT
R = 50Ω
OUTPUT
ALL INPUT PULSES
90%
VDDQ
GND
90%
10%
Z = 50Ω
0
10%
L
5 pF
R = 1538Ω
≤ 1 ns
≤ 1 ns
V = 1.25V
L
INCLUDING
JIG AND
SCOPE
(c)
(a)
(b)
Note:
14. Tested initially and after any design or process change that may affect these parameters.
Document #: 38-05283 Rev. *G
Page 20 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Switching Characteristics Over the Operating Range[19, 20]
250 MHz
200 MHz
167 MHz
Parameter
tPOWER
Clock
tCYC
Description
VDD(Typical) to the first access[15]
Min. Max. Min. Max. Min. Max.
Unit
1
1
1
ms
Clock Cycle Time
Clock HIGH
4.0
2.0
2.0
5.0
2.0
2.0
6.0
2.4
2.4
ns
ns
ns
tCH
tCL
Clock LOW
Output Times
tCO
Data Output Valid After CLK Rise
Data Output Hold After CLK Rise
Clock to Low-Z[16, 17, 18]
3.0
3.0
3.4
ns
ns
ns
ns
ns
ns
ns
tDOH
1.3
1.3
1.3
1.3
1.5
1.5
tCLZ
tCHZ
Clock to High-Z[16, 17, 18]
3.0
3.0
3.0
3.0
3.4
3.4
tOEV
OE LOW to Output Valid
tOELZ
tOEHZ
Set-up Times
tAS
OE LOW to Output Low-Z[16, 17, 18]
OE HIGH to Output High-Z[16, 17, 18]
0
0
0
3.0
3.0
3.4
Address Set-up Before CLK Rise
ADSC, ADSP Set-up Before CLK Rise
ADV Set-up Before CLK Rise
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.4
1.5
1.5
1.5
1.5
1.5
1.5
ns
ns
ns
ns
ns
ns
tADS
tADVS
tWES
GW, BWE, BWX Set-up Before CLK Rise
Data Input Set-up Before CLK Rise
Chip Enable Set-Up Before CLK Rise
tDS
tCES
Hold Times
tAH
Address Hold After CLK Rise
ADSP, ADSC Hold After CLK Rise
ADV Hold After CLK Rise
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.4
0.5
0.5
0.5
0.5
0.5
0.5
ns
ns
ns
ns
ns
ns
tADH
tADVH
tWEH
GW, BWE, BWX Hold After CLK Rise
Data Input Hold After CLK Rise
Chip Enable Hold After CLK Rise
tDH
tCEH
Notes:
15. This part has a voltage regulator internally; t
is the time that the power needs to be supplied above V (minimum) initially before a read or write operation
DD
POWER
can be initiated.
16. t
, t
,t
, and t
are specified with AC test conditions shown in part (b) of AC Test Loads. Transition is measured ± 200 mV from steady-state voltage.
OEHZ
CHZ CLZ OELZ
17. At any given voltage and temperature, t
is less than t
and t
is less than t
to eliminate bus contention between SRAMs when sharing the same
OEHZ
OELZ
CHZ
CLZ
data bus. These specifications do not imply a bus contention condition, but reflect parameters guaranteed over worst case user conditions. Device is designed
to achieve High-Z prior to Low-Z under the same system conditions.
18. This parameter is sampled and not 100% tested.
19. Timing reference level is 1.5V when V
= 3.3V and is 1.25V when V
= 2.5V.
DDQ
DDQ
20. Test conditions shown in (a) of AC Test Loads unless otherwise noted.
Document #: 38-05283 Rev. *G
Page 21 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Switching Waveforms
Read Cycle Timing[21]
t
CYC
CLK
t
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC
t
t
ADH
ADS
t
t
AH
AS
A1
A2
A3
ADDRESS
Burst continued with
new base address
t
t
WEH
WES
GW, BWE,
BWx
Deselect
cycle
t
t
CEH
CES
CE
t
t
ADVH
ADVS
ADV
OE
ADV
suspends
burst.
t
t
OEV
CO
t
t
OEHZ
t
OELZ
t
CHZ
DOH
t
CLZ
t
Q(A2)
Q(A2 + 1)
Q(A2 + 2)
Q(A2 + 3)
Q(A2)
Q(A2 + 1)
Q(A1)
Data Out (Q)
High-Z
CO
Burst wraps around
to its initial state
Single READ
BURST READ
DON’T CARE
UNDEFINED
Note:
21. On this diagram, when CE is LOW: CE is LOW, CE is HIGH and CE is LOW. When CE is HIGH: CE is HIGH or CE is LOW or CE is HIGH.
1
2
3
1
2
3
Document #: 38-05283 Rev. *G
Page 22 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Switching Waveforms (continued)
Write Cycle Timing[21, 22]
t
CYC
CLK
t
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC extends burst
t
t
ADH
ADS
t
t
ADH
ADS
ADSC
ADDRESS
BWE,
t
t
AH
AS
A1
A2
A3
Byte write signals are
ignored for first cycle when
ADSP initiates burst
t
t
WEH
WES
BW
X
t
t
WEH
WES
GW
CE
t
t
CEH
CES
t
t
ADVH
ADVS
ADV
OE
ADV suspends burst
t
t
DH
DS
Data In (D)
D(A2)
D(A2 + 1)
D(A2 + 1)
D(A2 + 2)
D(A2 + 3)
D(A3)
D(A3 + 1)
D(A3 + 2)
D(A1)
High-Z
t
OEHZ
Data Out (Q)
BURST READ
Single WRITE
BURST WRITE
Extended BURST WRITE
DON’T CARE
UNDEFINED
Note:
22.
Full width write can be initiated by either GW LOW; or by GW HIGH, BWE LOW and BW LOW.
X
Document #: 38-05283 Rev. *G
Page 23 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Switching Waveforms (continued)
Read/Write Cycle Timing[21, 23, 24]
t
CYC
CLK
t
t
CL
CH
t
t
ADH
ADS
ADSP
ADSC
t
t
AH
AS
A1
A2
A3
A4
A5
A6
ADDRESS
BWE,
t
t
WEH
WES
BW
X
t
t
CEH
CES
CE
ADV
OE
t
t
DH
t
CO
DS
t
OELZ
Data In (D)
High-Z
High-Z
D(A3)
D(A5)
D(A6)
t
t
OEHZ
CLZ
Data Out (Q)
Q(A1)
Q(A2)
Q(A4)
Q(A4+1)
Q(A4+2)
Q(A4+3)
Back-to-Back READs
Single WRITE
BURST READ
Back-to-Back
WRITEs
DON’T CARE
UNDEFINED
Notes:
23. The data bus (Q) remains in high-Z following a WRITE cycle, unless a new read access is initiated by ADSP or ADSC.
24. GW is HIGH.
Document #: 38-05283 Rev. *G
Page 24 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Switching Waveforms (continued)
ZZ Mode Timing[25, 26]
CLK
t
t
ZZ
ZZREC
ZZ
t
ZZI
I
SUPPLY
I
DDZZ
t
RZZI
ALL INPUTS
(except ZZ)
DESELECT or READ Only
Outputs (Q)
High-Z
DON’T CARE
Notes:
25. Device must be deselected when entering ZZ mode. See Cycle Descriptions table for all possible signal conditions to deselect the device.
26. DQs are in high-Z when exiting ZZ sleep mode
Document #: 38-05283 Rev. *G
Page 25 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Ordering Information
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Part and Package Type
167 CY7C1480V33-167AXC 51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1482V33-167AXC
Commercial
CY7C1480V33-167BZC
CY7C1482V33-167BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-167BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-167BZXC
CY7C1486V33-167BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1486V33-167BGXC
CY7C1480V33-167AXI
CY7C1482V33-167AXI
CY7C1480V33-167BZI
CY7C1482V33-167BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
lndustrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-167BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-167BZXI
CY7C1486V33-167BGI
CY7C1486V33-167BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
200 CY7C1480V33-200AXC 51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1482V33-200AXC
Commercial
CY7C1480V33-200BZC
CY7C1482V33-200BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-200BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-200BZXC
CY7C1486V33-200BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1486V33-200BGXC
CY7C1480V33-200AXI
CY7C1482V33-200AXI
CY7C1480V33-200BZI
CY7C1482V33-200BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
lndustrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-200BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-200BZXI
CY7C1486V33-200BGI
CY7C1486V33-200BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
Document #: 38-05283 Rev. *G
Page 26 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Ordering Information (continued)
Not all of the speed, package and temperature ranges are available. Please contact your local sales representative or
visit www.cypress.com for actual products offered.
Speed
(MHz)
Package
Diagram
Operating
Range
Ordering Code
Part and Package Type
250 CY7C1480V33-250AXC 51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
CY7C1482V33-250AXC
Commercial
CY7C1480V33-250BZC
CY7C1482V33-250BZC
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-250BZXC 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-250BZXC
CY7C1486V33-250BGC 51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
CY7C1486V33-250BGXC
CY7C1480V33-250AXI
CY7C1482V33-250AXI
CY7C1480V33-250BZI
CY7C1482V33-250BZI
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
51-85050 100-Pin Thin Quad Flat Pack (14 x 20 x 1.4 mm) Lead-Free
Industrial
51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm)
CY7C1480V33-250BZXI 51-85165 165-ball Fine-Pitch Ball Grid Array (15 x 17 x 1.4mm) Lead-Free
CY7C1482V33-250BZXI
CY7C1486V33-250BGI
CY7C1486V33-250BGXI
51-85167 209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm)
209-ball Fine-Pitch Ball Grid Array (14 × 22 × 1.76 mm) Lead-Free
Document #: 38-05283 Rev. *G
Page 27 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Package Diagrams
100-Pin Thin Plastic Quad Flatpack (14 x 20 x 1.4 mm) (51-85050)
16.00 0.20
14.00 0.10
1.40 0.05
100
81
80
1
0.30 0.08
0.65
TYP.
12° 1°
(8X)
SEE DETAIL
A
30
51
31
50
0.20 MAX.
1.60 MAX.
R 0.08 MIN.
0.20 MAX.
0° MIN.
SEATING PLANE
STAND-OFF
0.05 MIN.
0.15 MAX.
NOTE:
1. JEDEC STD REF MS-026
0.25
GAUGE PLANE
2. BODY LENGTH DIMENSION DOES NOT INCLUDE MOLD PROTRUSION/END FLASH
MOLD PROTRUSION/END FLASH SHALL NOT EXCEED 0.0098 in (0.25 mm) PER SIDE
R 0.08 MIN.
0.20 MAX.
BODY LENGTH DIMENSIONS ARE MAX PLASTIC BODY SIZE INCLUDING MOLD MISMATCH
3. DIMENSIONS IN MILLIMETERS
0°-7°
0.60 0.15
0.20 MIN.
51-85050-*B
1.00 REF.
DETAIL
A
Document #: 38-05283 Rev. *G
Page 28 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Package Diagrams (continued)
165-ball FBGA (15 x 17 x 1.4 mm) (51-85165)
PIN 1 CORNER
BOTTOM VIEW
TOP VIEW
Ø0.05 M C
PIN 1 CORNER
Ø0.25 M C A B
Ø0.45 0.05(165X)
1
2
3
4
5
6
7
8
9
10
11
11 10
9
8
7
6
5
4
3
2
1
A
B
A
B
C
D
C
D
E
E
F
F
G
G
H
J
H
J
K
K
L
L
M
M
N
P
R
N
P
R
A
1.00
5.00
10.00
B
15.00 0.10
0.15(4X)
SEATING PLANE
C
51-85165-*A
Document #: 38-05283 Rev. *G
Page 29 of 31
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
Package Diagrams (continued)
209-ball FBGA (14 x 22 x 1.76 mm) (51-85167)
51-85167-**
i486 is a trademark and Intel and Pentium are registered trademarks of Intel Corporation. All products and company names
mentioned in this document may be the trademarks of their respective holders
Document #: 38-05283 Rev. *G
Page 30 of 31
© Cypress Semiconductor Corporation, 2006. The information contained herein is subject to change without notice. Cypress Semiconductor Corporation assumes no responsibility for the use
of any circuitry other than circuitry embodied in a Cypress product. Nor does it convey or imply any license under patent or other rights. Cypress products are not warranted nor intended to be
used for medical, life support, life saving, critical control or safety applications, unless pursuant to an express written agreement with Cypress. Furthermore, Cypress does not authorize its
products for use as critical components in life-support systems where a malfunction or failure may reasonably be expected to result in significant injury to the user. The inclusion of Cypress
products in life-support systems application implies that the manufacturer assumes all risk of such use and in doing so indemnifies Cypress against all charges.
[+] Feedback
CY7C1480V33
CY7C1482V33
CY7C1486V33
.Document History Page
Document Title: CY7C1480V33/CY7C1482V33/CY7C1486V33 72-Mbit (2M x 36/4M x 18/1M x 72) Pipelined Sync SRAM
Document Number: 38-05283
Orig. of
REV.
**
ECN NO. Issue Date Change
Description of Change
114670
118281
08/06/02
01/21/03
PKS
HGK
New Data Sheet
*A
Changed tCO from 2.4 to 2.6 ns for 250 MHz
Updated features on page 1 for package offering
Removed 30-MHz offering
Updated Ordering Information
Changed Advanced Information to Preliminary
*B
233368
See ECN
NJY
Changed timing diagrams
Changed logic block diagrams
Modified Functional Description
Modified “Functional Overview” section
Added boundary scan order for all packages
Included thermal numbers and capacitance values for all packages
Included IDD and ISB values
Removed 250-MHz speed grade offering and included 225-MHz speed bin
Changed package outline for 165FBGA package and 209-ball BGA package
Removed 119-BGA package offering
*C
*D
299452
323080
See ECN
SYT
Removed 225-MHz offering and included 250-MHz speed bin
Changed tCYC from 4.4 ns to 4.0 ns for 250-MHz Speed Bin
Changed ΘJA from 16.8 to 24.63 °C/W and ΘJC from 3.3 to 2.28 °C/W for 100
TQFP Package on Page # 20
Added lead-free information for 100-Pin TQFP, 165 FBGA and 209 BGA
Packages
Added comment of ‘Lead-free BG packages availability’ below the Ordering
Information
See ECN
PCI
Unshaded 200 and 167 MHz speed bin in the AC/DC Table and Selection
Guide
Address expansion pins/balls in the pinouts for all packages are modified as
per JEDEC standard
Added Address Expansion pins in the Pin Definitions Table
Added Truth Table and Note# 7 for CY7C1486V33 on page# 11
Added Industrial Operating Range
Modified VOL, VOH test conditions
Removed comment of ‘Lead-free BG packages availability’ below the
Ordering Information
Updated Ordering Information Table
*E
416193
See ECN
NXR
Converted Preliminary to Final
Changed address of Cypress Semiconductor Corporation on Page# 1 from
“3901 North First Street” to “198 Champion Court”
Changed the description of IX from Input Load Current to Input Leakage
Current on page# 19
Changed the IX current values of MODE on page # 19 from -5 µA and 30 µA
to -30 µA and 5 µA
Changed the IX current values of ZZ on page # 19 from -30 µA and 5 µA
to -5 µA and 30 µA
Changed VIH < VDD to VIH < VDD on page # 19
Replaced Package Name column with Package Diagram in the Ordering
Information table
Updated the Ordering Information Table
*F
470723
486690
See ECN
See ECN
VKN
VKN
Added the Maximum Rating for Supply Voltage on VDDQ Relative to GND
Changed tTH,tTL from 25 ns to 20 ns and tTDOV from 5 ns to 10 ns in TAP AC
Switching Characteristics table
Updated the Ordering Information table
*G
Corrected the typo in the 209-Ball FBGA pinout.
(Corrected the ball name H9 to VSS from VSSQ).
Document #: 38-05283 Rev. *G
Page 31 of 31
[+] Feedback
相关型号:
©2020 ICPDF网 联系我们和版权申明