R8C-AN1P2B [EVERLIGHT]
Chip LED with Right Angle Lens; LED芯片与直角透镜型号: | R8C-AN1P2B |
厂家: | EVERLIGHT ELECTRONICS CO., LTD |
描述: | Chip LED with Right Angle Lens |
文件: | 总10页 (文件大小:217K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
EVERLIGHT ELECTRONICS CO.,LTD.
Technical Data Sheet
Chip LED with Right Angle Lens
12-215/R8C-AN1P2B/3C
Features
․Package in 8mm tape on 7〞diameter reel.
․Compatible with automatic placement equipment.
․Compatible with infrared and vapor phase reflow
solder process.
․Mono-color type.
․Pb-free.
․The product itself will remain within RoHS compliant version.
Descriptions
․The 12-215 SMD Taping is much smaller than
lead frame type components, thus enable smaller
board size, higher packing density, reduced
storage space and finally smaller equipment to be
obtained.
․Besides, lightweight makes them ideal for
miniature applications. etc.
Applications
․Backlighting in dashboard and switch.
․Telecommunication: indicator and backlighting in
telephone and fax.
․Flat backlight for LCD, switch and symbol.
․General use.
Device Selection Guide
Chip
Lens Color
Part No.
Material
Emitted Color
12-215/R8C-AN1P2B/3C
AlGaInP
Deep-Red
Water Clear
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 1 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Package Outline Dimensions
C
L
1.7 0.2
±
2.1 0.2
±
R0.5
1.5
2.2
Cathode mark
0.9
Note: The tolerances unless mentioned is ±0.1mm, Unit = mm
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 2 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Absolute Maximum Ratings (Ta=25℃)
Parameter
Reverse Voltage
Symbol
VR
Rating
5
Unit
V
mA
℃
Forward Current
IF
25
Operating Temperature
Storage Temperature
Electrostatic Discharge(HBM)
Topr
Tstg
ESD
Pd
-40 ~ +85
-40 ~ +90
2000
℃
V
Power Dissipation
Peak Forward Current
(Duty 1/10 @1KHz)
60
mW
IFP
mA
60
Reflow Soldering : 260 ℃ for 10 sec.
Hand Soldering : 350 ℃ for 3 sec.
Soldering Temperature
Tsol
Electro-Optical Characteristics (Ta=25℃)
Parameter
Symbol
Min.
Typ.
Max.
Unit
Condition
IF=20mA
VR=5V
Luminous Intensity
mcd
nm
IV
28.5
----
-----
632
72.0
----
Peak Wavelength
λp
Dominant Wavelength
629.5
-----
-----
20
645.5
----
λd
nm
Spectrum Radiation
Bandwidth
△λ
nm
Viewing Angle
2θ1/2
-----
130
----
deg
Forward Voltage
VF
IR
V
1.75
----
-----
----
2.35
10
Reverse Current
µA
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 3 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Bin Range Of Dom. Wavelength
Group
Bin
E7
Min
Max
633.5
637.5
641.5
645.5
Unit
nm
Condition
IF =20mA
629.5
633.5
637.5
641.5
E8
A
E9
E10
Bin Range Of Luminous Intensity
Bin
N1
N2
P1
Min
28.5
36.0
45.0
Max
Unit
mcd
Condition
IF =20mA
36.0
45.0
57.0
P2
57.0
72.0
Bin Range Of Luminous Voltage
Group
Bin
0
Min
1.75
1.95
2.15
Max
Unit
V
Condition
IF =20mA
1.95
2.15
2.35
B
1
2
Notes:
1.Tolerance of Luminous Intensity ±10%
2.Tolerance of Dominant Wavelength ±1nm
3.Tolerance of Forward Voltage ±0.1V
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 4 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Electro-Optical Characteristics (Ta=25℃)
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 5 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Label explanation
CAT: Luminous Intensity Rank
HUE: Dom. Wavelength Rank
REF: Forward Voltage Rank
xxxxxx
xxxxxx
RoHS
xxxxxxxxxxxx
xxxx
xxxxxxxx
Reel Dimensions
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 6 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Carrier Tape Dimensions: Loaded quantity 3000 PCS per reel
Note: The tolerances unless mentioned is ±0.1mm ,Unit = mm
Moisture Resistant Packaging
Aluminum moisture-proof bag
Label
Desiccant
Label
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 7 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Reliability Test Items And Conditions
The reliability of products shall be satisfied with items listed below.
Confidence level:90%
LTPD:10%
Test
Hours/Cycles
Sample
Size
No.
1
Items
Test Condition
Ac/Re
0/1
Temp. : 260℃±5℃
Reflow Soldering
22 PCS.
6 Min.
Min. 5sec.
H : +100℃ 15min
0/1
2
Temperature Cycle
Thermal Shock
22 PCS.
∫ 5 min
L : -40℃ 15min
300 Cycles
H : +100℃ 5min
0/1
0/1
3
4
22 PCS.
22 PCS.
∫ 10 sec
L : -10℃ 5min
300 Cycles
1000 Hrs.
High Temperature
Storage
Low Temperature
Storage
Temp. : 100℃
Temp. : -40℃
0/1
0/1
0/1
5
6
7
22 PCS.
22 PCS.
22 PCS.
1000 Hrs.
1000 Hrs.
DC Operating Life
IF = 20 mA
High Temperature /
High Humidity
85℃/ 85% RH
1000 Hrs.
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 8 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
Precautions For Use
1. Over-current-proof
Customer must apply resistors for protection , otherwise slight voltage shift will cause big
current change ( Burn out will happen ).
2. Storage
2.1 Do not open moisture proof bag before the products are ready to use.
2.2 Before opening the package: The LEDs should be kept at 30℃ or less and 90%RH or less.
2.3After opening the package, the LEDs should be kept at 30℃ or less and 60%RH or less(Floor life).
However,it’s recommended that The LEDs should be used within 168 hours (7 days) after opening
the package.If unused LED remain, it should be stored in moisture proof packages.
2.4 If the moisture absorbent material (silica gel) has faded away or the LEDs have exceeded the
storage time, baking treatment should be performed using the following conditions.
Baking treatment : 60±5℃ for 24 hours.
3. Soldering Condition
3.1 Pb-free solder temperature profile
3.2 Reflow soldering should not be done more than two times.
3.3 When soldering, do not put stress on the LEDs during heating.
3.4 After soldering, do not warp the circuit board.
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Rev 1
Page: 9 of 10
Prepared date: 02-June-2006
Prepared by: Wu xiaowei
EVERLIGHT ELECTRONICS CO.,LTD.
12-215/R8C-AN1P2B/3C
4.Soldering Iron
Each terminal is to go to the tip of soldering iron temperature less than350℃ for 3 seconds
within once in less than the soldering iron capacity 25W. Leave two seconds and more intervals, and do
soldering of each terminal. Be careful because the damage of the product is often started at the time of
the hand solder.
5.Repairing
Repair should not be done after the LEDs have been soldered. When repairing is unavoidable, a
double-head soldering iron should be used (as below figure). It should be confirmed beforehand whether
the characteristics of the LEDs will or will not be damaged by repairing.
EVERLIGHT ELECTRONICS CO., LTD.
Office: No 25, Lane 76, Sec 3, Chung Yang Rd,
Tucheng, Taipei 236, Taiwan, R.O.C
Tel: 886-2-2267-2000, 2267-9936
Fax: 886-2267-6244, 2267-6189, 2267-6306
http://www.everlight.com
Everlight Electronics Co., Ltd.
Device No:SZDSE-125-R06
http://www.everlight.com
Prepared date: 02-June-2006
Rev 1
Page: 10 of 10
Prepared by: Wu xiaowei
相关型号:
©2020 ICPDF网 联系我们和版权申明