HMC579 [HITTITE]
GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT; 砷化镓MMIC X2有源倍频器, 32 - 46 GHz的输出型号: | HMC579 |
厂家: | HITTITE MICROWAVE CORPORATION |
描述: | GaAs MMIC x2 ACTIVE FREQUENCY MULTIPLIER, 32 - 46 GHz OUTPUT |
文件: | 总6页 (文件大小:273K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Typical Applications
Features
The HMC579 is suitable for:
High Output Power: +13 dBm
Low Input Power Drive: 0 to +6 dBm
Fo Isolation: >25 dBc @ Fout= 38 GHz
100 KHz SSB Phase Noise: -127 dBc/Hz
Single Supply: +5V@ 70 mA
2
• Clock Generation Applications:
SONET OC-192 & SDH STM-64
• Point-to-Point & VSAT Radios
• Test Instrumentation
• Military EW / Radar
• Space
Die Size: 1.18 mm x 1.23 mm x 0.1 mm
Functional Diagram
General Description
The HMC579 die is a x2 active broadband frequency
multiplier utilizing GaAs PHEMT technology. When
driven by a +3 dBm signal, the multiplier provides +13
dBm typical output power from 32 to 46 GHz. The Fo
isolation is >25 dBc at 38 GHz. The HMC579 is ideal
for use in LO multiplier chains for Pt to Pt & VSAT
Radios yielding reduced parts count vs. traditional
approaches. The low additive SSB Phase Noise of
-127 dBc/Hz at 100 kHz offset helps maintain good
system noise performance.
Electrical Specifications, TA = +25° C, Vdd1, Vdd2 = 5.0V, 3 dBm Drive Level
Parameter
Min.
Typ.
16 - 23
32 - 46
13
Max.
Units
GHz
GHz
dBm
dBc
Frequency Range, Input
Frequency Range, Output
Output Power
8
Fo Isolation (with respect to output level)
Input Return Loss
25
12
dB
Output Return Loss
8
dB
SSB Phase Noise (100 kHz Offset)
Supply Current (Idd1, Idd2)
-127
70
dBc/Hz
mA
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 50
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Output Power vs.
Temperature @ 3 dBm Drive Level
Output Power vs. Drive Level
20
18
16
14
12
10
8
25
20
15
10
5
2
0
-5
6
4
2
0
-10
+25C
+85C
-55C
-6dBm
-4dBm
-2dBm
0dBm
2dBm
4dBm
6dBm
-15
-20
-25
30
32
34
36
38
40
42
44
46
48
30
32
34
36
38
40
42
44
46
48
OUTPUT FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
Output Power vs.
Supply Voltage @ 3 dBm Drive Level
Isolation @ 3 dBm Drive Level
20
18
16
14
12
10
8
20
10
Fo
2Fo
0
-10
6
4
2
0
4.5V
5.0V
5.5V
-20
-30
30
32
34
36
38
40
42
44
46
48
30
32
34
36
38
40
42
44
46
48
OUTPUT FREQUENCY (GHz)
OUTPUT FREQUENCY (GHz)
Output Power vs. Input Power
20
15
10
5
0
-5
32GHz
39GHz
46GHz
-10
-15
-20
-10
-8
-6
-4
-2
0
2
4
6
8
10
INPUT POWER (dBm)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 51
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Input Return Loss vs. Temperature
Output Return Loss vs. Temperature
0
0
-2
2
+25C
+85C
-55C
-5
-10
-15
-20
-25
-4
-6
-8
-10
-12
-14
-16
-18
-20
+25C
+85C
-55C
15
16
17
18
19
20
21
22
23
24
30
32
34
36
38
40
42
44
46
48
FREQUENCY (GHz)
FREQUENCY (GHz)
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 52
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Absolute Maximum Ratings
Typical Supply Current vs. Vdd
RF Input (Vdd = +5V)
+13 dBm
Vdd (Vdc)
Idd (mA)
2
Supply Voltage (Vdd1, Vdd2)
Channel Temperature
+6.0 Vdc
175 °C
4.5
69
70
70
5.0
Continuous Pdiss (T= 85 °C)
(derate 7.3 mW/°C above 85 °C)
5.5
656 mW
Note:
Thermal Resistance
(Channel to die bottom)
137 °C/W
Multiplier will operate over full voltage range shown above.
Storage Temperature
Operating Temperature
-65 to +150 °C
-55 to +85 °C
ELECTROSTATIC SENSITIVE DEVICE
OBSERVE HANDLING PRECAUTIONS
Outline Drawing
Die Packaging Information [1]
NOTES:
1. ALL DIMENSIONS ARE IN INCHES [MILLIMETERS].
2. DIE THICKNESS IS .004”
[2]
Standard
Alternate
3. TYPICAL BOND PAD IS .004” SQUARE.
4. TYPICAL BOND SPACING IS .006” CENTER TO CENTER.
5. BOND PAD METALIZATION: GOLD
6. BACKSIDE METALIZATION: GOLD
7. BACKSIDE METAL IS GROUND.
GP-2
—
[1] Refer to the “Packaging Information” section for die
packaging dimensions.
[2] Reference this suffix only when ordering alternate die
packaging.
8. NO CONNECTION REQUIRED FOR UNLABELED BOND PADS.
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 53
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Pad Description
Pad Number
Function
Description
Interface Schematic
2
1, 2
Vdd1, Vdd2
Supply voltage 5V 0.5V.
Pin is AC coupled and matched to
50 Ohms from 32 - 46 GHz.
3
4, 5
6
RFOUT
GND
Die bottom must be connected to RF ground.
Pin is AC coupled and matched to
50 Ohms from 16 - 23 GHz.
RFIN
Assembly Diagram
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 54
HMC579
v00.0506
GaAs MMIC x2 ACTIVE FREQUENCY
MULTIPLIER, 32 - 46 GHz OUTPUT
Mounting & Bonding Techniques for Millimeterwave GaAs MMICs
The die should be attached directly to the ground plane eutectically or with
conductive epoxy (see HMC general Handling, Mounting, Bonding Note).
0.102mm (0.004”) Thick GaAs MMIC
2
50 Ohm Microstrip transmission lines on 0.127mm (5 mil) thick alumina thin film
substrates are recommended for bringing RF to and from the chip (Figure 1). If
0.254mm (10 mil) thick alumina thin film substrates must be used, the die should
be raised 0.150mm (6 mils) so that the surface of the die is coplanar with the
surface of the substrate. One way to accomplish this is to attach the 0.102mm
(4 mil) thick die to a 0.150mm (6 mil) thick molybdenum heat spreader (moly-tab)
which is then attached to the ground plane (Figure 2).
Wire 3 mil Ribbon Bond
0.076mm
(0.003”)
RF Ground Plane
Microstrip substrates should be brought as close to the die as possible in order
to minimize ribbon bond length. Typical die-to-substrate spacing is 0.076mm (3
mils). Gold ribbon of 0.075 mm (3 mil) width and minimal length <0.31 mm (<12
mils) is recommended to minimize inductance on RF, LO & IF ports.
0.127mm (0.005”) Thick Alumina
Thin Film Substrate
An RF bypass capacitor should be used on the Vdd input. A 100 pF single layer
capacitor (mounted eutectically or by conductive epoxy) placed no further than
0.762mm (30 Mils) from the chip is recommended.
Figure 1.
0.102mm (0.004”) Thick GaAs MMIC
Handling Precautions
Follow these precautions to avoid permanent damage.
Ribbon Bond
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
0.076mm
(0.003”)
Cleanliness: Handle the chips in a clean environment. DO NOT attempt to clean
the chip using liquid cleaning systems.
RF Ground Plane
Storage: All bare die are placed in either Waffle or Gel based ESD protective
containers, and then sealed in an ESD protective bag for shipment. Once the
sealed ESD protective bag has been opened, all die should be stored in a dry
nitrogen environment.
0.150mm (0.005”) Thick
Moly Tab
0.254mm (0.010”) Thick Alumina
Thin Film Substrate
Static Sensitivity: Follow ESD precautions to protect against > 250V ESD
strikes.
Figure 2.
Transients: Suppress instrument and bias supply transients while bias is applied. Use shielded signal and bias cables to minimize
inductive pick-up.
General Handling: Handle the chip along the edges with a vacuum collet or with a sharp pair of bent tweezers. The surface of the
chip has fragile air bridges and should not be touched with vacuum collet, tweezers, or fingers.
Mounting
The chip is back-metallized and can be die mounted with AuSn eutectic preforms or with electrically conductive epoxy. The
mounting surface should be clean and flat.
Eutectic Die Attach: A 80/20 gold tin preform is recommended with a work surface temperature of 255 deg. C and a tool temperature
of 265 deg. C. When hot 90/10 nitrogen/hydrogen gas is applied, tool tip temperature should be 290 deg. C. DO NOT expose the
chip to a temperature greater than 320 deg. C for more than 20 seconds. No more than 3 seconds of scrubbing should be required
for attachment.
Epoxy Die Attach: Apply a minimum amount of epoxy to the mounting surface so that a thin epoxy fillet is observed around the
perimeter of the chip once it is placed into position. Cure epoxy per the manufacturer’s schedule.
Wire Bonding
Ball or wedge bond with 0.025mm (1 mil) diameter pure gold wire. Thermosonic wirebonding with a nominal stage temperature of
150 deg. C and a ball bonding force of 40 to 50 grams or wedge bonding force of 18 to 22 grams is recommended. Use the minimum
level of ultrasonic energy to achieve reliable wirebonds. Wirebonds should be started on the chip and terminated on the package or
substrate. All bonds should be as short as possible <0.31mm (12 mils).
For price, delivery, and to place orders, please contact Hittite Microwave Corporation:
20 Alpha Road, Chelmsford, MA 01824 Phone: 978-250-3343 Fax: 978-250-3373
Order On-line at www.hittite.com
2 - 55
相关型号:
HMC580ST89ETR
Wide Band Low Power Amplifier, 0MHz Min, 1000MHz Max, ROHS COMPLIANT, PLASTIC, SOT-89, SMT, 3 PIN
HITTITE
©2020 ICPDF网 联系我们和版权申明