HS-1135RH [INTERSIL]
Radiation Hardened, High Speed, Low Power Current Feedback Amplifier with Programmable Output Limiting; 抗辐射，高速，低功耗电流反馈放大器，可编程输出限制
| 型号： | HS-1135RH |
| 厂家： | 
Intersil |
| 描述： | Radiation Hardened, High Speed, Low Power Current Feedback Amplifier with Programmable Output Limiting |
| 文件： | 总5页 (文件大小：65K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
HS-1135RH
Data Sheet
August 1999
File Number 4099.2
Radiation Hardened, High Speed, Low
Power Current Feedback Amplifier with
Programmable Output Limiting
Features
• Electrically Screened to SMD # 5962-96767
• QML Qualified per MIL-PRF-38535 Requirements
• User Programmable Output Voltage Limiting
The HS-1135RH is a radiation hardened, high speed, low
power current feedback amplifier built with Intersil’s
proprietary complementary bipolar UHF-1 (DI bonded wafer)
process. They are QML approved and processed in full
compliance with MIL-PRF-38535. This amplifier features
• Fast Overdrive Recovery . . . . . . . . . . . . . . . . . <1ns (Typ)
• Low Supply Current . . . . . . . . . . . . . . . . . . . . 6.9mA (Typ)
• Wide -3dB Bandwidth. . . . . . . . . . . . . . . . . .360MHz (Typ)
• High Slew Rate. . . . . . . . . . . . . . . . . . . . . .1200V/µs (Typ)
• High Input Impedance . . . . . . . . . . . . . . . . . . . 2MΩ (Typ)
• Excellent Gain Flatness (to 50MHz). . . . . . ±0.07dB (Typ)
• Total Gamma Dose. . . . . . . . . . . . . . . . . . . . 300kRAD(Si)
• Latch Up. . . . . . . . . . . . . . . . . . . . . None (DI Technology)
user programmable output limiting, via the V and V pins.
H
L
The HS-1135RH is the ideal choice for high speed, low
power applications requiring output limiting (e.g., flash A/D
drivers), especially those requiring fast overdrive recovery
times. The limiting function allows the designer to set the
maximum and minimum output levels to protect downstream
stages from damage or input saturation. The sub-
nanosecond overdrive recovery time ensures a quick return
to linear operation following an overdrive condition.
Applications
Component and composite video systems also benefit from
this op amp’s performance, as indicated by the gain flatness,
and differential gain and phase specifications.
• Flash A/D Driver
• Video Switching and Routing
• Pulse and Video Amplifiers
• Wideband Amplifiers
• RF/IF Signal Processing
• Imaging Systems
Specifications for Rad Hard QML devices are controlled
by the Defense Supply Center in Columbus (DSCC). The
SMD numbers listed here must be used when ordering.
Detailed Electrical Specifications for these devices are
contained in SMD 5962-96767. A “hot-link” is provided
on our homepage for downloading.
Pinout
http://www.intersil.com/spacedefense/space.htm
HS-1135RH
GDIP1-T8 (CERDIP)
OR CDIP2-TI (SBDIP)
TOP VIEW
Ordering Information
INTERNAL
TEMP. RANGE
o
ORDERING NUMBER
5962F9676701VPA
5962F9676701VPC
HS7-1135RH/PROTO
MKT. NUMBER
( C)
HS7-1135RH-Q
-55 to 125
-55 to 125
-55 to 125
NC
-IN
+IN
V-
1
2
3
4
8
7
6
5
V
H
V+
HS7B-1135RH-Q
HS7-1135RH/PROTO
-
+
OUT
V
L
CAUTION: These devices are sensitive to electrostatic discharge; follow proper IC Handling Procedures.
1-888-INTERSIL or 321-724-7143 | Copyright © Intersil Corporation 1999
1
HS-1135RH
the clamp inputs floating. A similar description applies to the
symmetrical low clamp circuitry controlled by V .
L
Clamp Operation
General
When the output is clamped, the negative input continues to
The HS-1135RH features user programmable output clamps
to limit output voltage excursions. Clamping action is obtained
by applying voltages to the V and V terminals (pins 8 and 5)
source a slewing current (I
) in an attempt to force the
CLAMP
output to the quiescent voltage defined by the input. Q must
P5
H
L
sink this current while clamping, because the -IN current is
always mirrored onto the high impedance node. The clamping
of the amplifier. V sets the upper output limit, while V sets
H
L
the lower clamp level. If the amplifier tries to drive the output
above V , or below V , the clamp circuitry limits the output
current is calculated as (V - V
)/R . As an example, a
-IN OUT
F
H
L
unity gain circuit with V = 2V, V = 1V, and R = 510Ω would
IN
H
F
voltage at V or V ( the clamp accuracy), respectively. The
H
L
have I
= (2-1)/510Ω = 1.96mA. Note that I
will
CLAMP
CC
low input bias currents of the clamp pins allow them to be
driven by simple resistive divider circuits, or active elements
such as amplifiers or DACs.
increase by I
CLAMP
when the output is clamp limited.
Clamp Accuracy
The clamped output voltage will not be exactly equal to the
voltage applied to V or V . Offset errors, mostly due to V
BE
mismatches, necessitate a clamp accuracy parameter which is
found in the device specifications. Clamp accuracy is a function
of the clamping conditions. Referring again to Figure 1, it can
Clamp Circuitry
H
L
Figure 1 shows a simplified schematic of the HS-1135RH
input stage, and the high clamp (V ) circuitry. As with all
current feedback amplifiers, there is a unity gain buffer (Q
H
X1
- Q ) between the positive and negative inputs. This buffer
X2
be seen that one component of clamp accuracy is the V
BE
forces -IN to track +IN, and sets up a slewing current of (V
-
mismatch between the Q transistors, and the Q transistors.
X6 X5
If the transistors always ran at the same current level there
- V
)/R . This current is mirrored onto the high
IN
OUT
F
impedance node (Z) by Q -Q , where it is converted to a
voltage and fed to the output via another unity gain buffer. If
no clamping is utilized, the high impedance node may swing
within the limits defined by Q and Q . Note that when the
output reaches it’s quiescent value, the current flowing
X3 X4
would be no V mismatch, and no contribution to the
BE
inaccuracy. The Q transistors are biased at a constant
X6
current, but as described earlier, the current through Q is
X5
increases,
P4 N4
equivalent to I
. V increases as I
CLAMP BE
CLAMP
causing the clamped output voltage to increase as well. I
CLAMP
) and
through -IN is reduced to only that small current (-I
required to keep the output at the final voltage.
)
BIAS
is a function of the overdrive level (V -V
-IN OUTCLAMPED
R ,so clamp accuracy degrades as the overdrive increases, or
F
V+
as R decreases. As an example, the specified accuracy of
F
±60mV for a 2X overdrive with R = 510Ω degrades to ±220mV
F
Q
Q
P3
P4
Z
for R = 240Ω at the same overdrive, or to ±250mV for a 3X
F
overdrive with R = 510Ω.
F
50K
(30K
FOR V )
L
Q
N2
R
1
Consideration must also be given to the fact that the clamp
voltages have an effect on amplifier linearity. The
“Nonlinearity Near Clamp Voltage” curve in the data sheet
illustrates the impact of several clamp levels on linearity.
Q
P1
V-
V+
I
CLAMP
+IN
+1
V
H
Q
N1
Q
N6
Clamp Range
Q
N5
200Ω
Q
Unlike some competitor devices, both V and V have usable
P2
H
L
Q
P6
ranges that cross 0V. While V must be more positive than V ,
both may be positive or negative, within the range restrictions
indicated in the specifications. For example, the HS-1135RH
H
L
Q
P5
Q
Q
N4
N3
could be limited to ECL output levels by setting V = -0.8V and
H
V-
V = -1.8V. V and V may be connected to the same voltage
L
H
L
R
F
(GND for instance) but the result won’t be in a DC output
voltage from an AC input signal. A 150 - 200mV AC signal will
still be present at the output.
-IN
(EXTERNAL)
V
OUT
FIGURE 1. HS-1135RH SIMPLIFIED V CLAMP CIRCUITRY
H
Recovery from Overdrive
Tracing the path from V to Z illustrates the effect of the
H
The output voltage remains at the clamp level as long as the
overdrive condition remains. When the input voltage drops
clamp voltage on the high impedance node. V decreases
H
by 2V (QN6 and QP6) to set up the base voltage on QP5.
BE
below the overdrive level (V ) the amplifier will
/A
CLAMP VCL
QP5 begins to conduct whenever the high impedance node
return to linear operation. A time delay, known as the
Overdrive Recovery Time, is required for this resumption of
linear operation. The plots of “Unclamped Performance” and
“Clamped Performance” highlight the HS-1135RH’s
reaches a voltage equal to QP5’s base + 2V (QP5 and
QN5). Thus, QP5 clamps node Z whenever Z reaches V .
H
R1 provides a pull-up network to ensure functionality with
BE
2
HS-1135RH
subnanosecond recovery time. The difference between the
The layout and schematic of the board are shown here:
unclamped and clamped propagation delays is the overdrive
recovery time. The appropriate propagation delays are 4.0ns
for the unclamped pulse, and 4.8ns for the clamped (2X
overdrive) pulse yielding an overdrive recovery time of
800ps. The measurement uses the 90% point of the output
transition to ensure that linear operation has resumed. Note:
The propagation delay illustrated is dominated by the
fixturing. The delta shown is accurate, but the true
HS-1135RH propagation delay is 500ps.
V
H
1
+IN
OUT
V-
V+
V
L
GND
Use of Die in Hybrid Applications
This amplifier is designed with compensation to negate the
package parasitics that typically lead to instabilities. As a
result, the use of die in hybrid applications results in
overcompensated performance due to lower parasitic
FIGURE 2A. TOP LAYOUT
capacitances. Reducing R below the recommended values
F
for packaged units will solve the problem. For A = +2 the
V
recommended starting point is 300Ω, while unity gain
applications should try 400Ω.
PC Board Layout
The frequency performance of this amplifier depends a great
deal on the amount of care taken in designing the PC board.
The use of low inductance components such as chip
resistors and chip capacitors is strongly recommended,
while a solid ground plane is a must!
FIGURE 2B. BOTTOM LAYOUT
Attention should be given to decoupling the power supplies.
A large value (10µF) tantalum in parallel with a small value
chip (0.1µF) capacitor works well in most cases.
Terminated microstrip signal lines are recommended at the
input and output of the device. Output capacitance, such as
that resulting from an improperly terminated transmission
line will degrade the frequency response of the amplifier and
may cause oscillations. In most cases, the oscillation can be
avoided by placing a resistor in series with the output.
500Ω
500Ω
50Ω
V
H
1
2
3
4
8
7
6
5
0.1µF
50Ω
10µF
+5V
IN
OUT
V
L
Care must also be taken to minimize the capacitance to
ground seen by the amplifier’s inverting input. The larger this
capacitance, the worse the gain peaking, resulting in pulse
overshoot and possible instability. To this end, it is
recommended that the ground plane be removed under
traces connected to pin 2, and connections to pin 2 should
be kept as short as possible.
10µF
0.1µF
GND
GND
-5V
FIGURE 2C. SCHEMATIC
FIGURE 2. EVALUATION BOARD SCHEMATIC AND LAYOUT
An example of a good high frequency layout is the
Evaluation Board shown in Figure 2.
Evaluation Board
An evaluation board is available for the HS-1135RH,
(HFA11XXEVAL). Please contact your local sales office for
information.
3
HS-1135RH
Burn-In Circuit
HS-1135RH CERDIP
R
2
1
2
3
4
8
7
6
5
D
2
R
R
1
V+
-
1
+
C
D
1
1
D
2
V-
D
C
1
1
NOTES:
1. R = 1kΩ, ±5% (Per Socket)
1
2. R = 10kΩ, ±5% (Per Socket)
2
3. C = 0.01µF (Per Socket) or 0.1µF (Per Row) Minimum
1
4. D = 1N4002 or Equivalent (Per Board)
1
5. D = 1N4002 or Equivalent (Per Socket)
2
6. V+ = +5.5V ±0.5V
7. V- = -5.5V ±0.5V
Irradiation Circuit
HS-1135RH CERDIP
R
2
1
2
3
4
8
7
6
5
R
R
1
V+
-
1
+
C
1
V-
C
2
NOTES:
8. R = 1kΩ, ±5%
1
9. R = 10kΩ, ±5%
2
10. C = C = 0.01µF
1
2
11. V+ = +5.0V ±0.5V
12. V- = -5.0V ±0.5V
4
HS-1135RH
Die Characteristics
DIE DIMENSIONS:
Substrate:
UHF-1, Bonded Wafer, DI
59 mils x 58.2 mils x 19 mils ±1 mil
1500µm x 1480µm x 483µm ±25.4µm
ASSEMBLY RELATED INFORMATION:
INTERFACE MATERIALS:
Glassivation:
Substrate Potential:
Floating
Type: Nitride
Thickness: 4kÅ ±0.5kÅ
ADDITIONAL INFORMATION:
Worst Case Current Density:
Top Metallization:
5
2
< 2 x 10 A/cm
Type: Metal 1: AICu(2%)/TiW
Thickness: Metal 1: 8kÅ ±0.4kÅ
Type: Metal 2: AICu(2%)
Transistor Count:
89
Thickness: Metal 2: 16kÅ ±0.8kÅ
Metallization Mask Layout
HS-1135RH
-IN
V
H
V+
OUT
+IN
V-
V
L
All Intersil semiconductor products are manufactured, assembled and tested under ISO9000 quality systems certification.
Intersil semiconductor products are sold by description only. Intersil Corporation reserves the right to make changes in circuit design and/or specifications at any time with-
out notice. Accordingly, the reader is cautioned to verify that data sheets are current before placing orders. Information furnished by Intersil is believed to be accurate and
reliable. However, no responsibility is assumed by Intersil or its subsidiaries for its use; nor for any infringements of patents or other rights of third parties which may result
from its use. No license is granted by implication or otherwise under any patent or patent rights of Intersil or its subsidiaries.
For information regarding Intersil Corporation and its products, see web site www.intersil.com
Sales Office Headquarters
NORTH AMERICA
EUROPE
ASIA
Intersil Corporation
Intersil SA
Mercure Center
100, Rue de la Fusee
1130 Brussels, Belgium
TEL: (32) 2.724.2111
FAX: (32) 2.724.22.05
Intersil (Taiwan) Ltd.
7F-6, No. 101 Fu Hsing North Road
Taipei, Taiwan
Republic of China
TEL: (886) 2 2716 9310
FAX: (886) 2 2715 3029
P. O. Box 883, Mail Stop 53-204
Melbourne, FL 32902
TEL: (321) 724-7000
FAX: (321) 724-7240
5
相关型号：
HS-1145RH
Radiation Hardened, High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable
INTERSIL
HS-1145RH_05
Radiation Hardened, High Speed, Low Power, Current Feedback Video Operational Amplifier with Output Disable
INTERSIL
©2020 ICPDF网 联系我们和版权申明