DSLP0080T023G6RP [LITTELFUSE]
SIDACTOR G.FAST 8V 30A SOT23-6;
| 型号： | DSLP0080T023G6RP |
| 厂家： | 
LITTELFUSE |
| 描述： | SIDACTOR G.FAST 8V 30A SOT23-6 双向触发二极管 |
| 文件： | 总5页 (文件大小：950K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
SIDACtor® ProtectionThyristors
Broadband Optimized™ Protection
RoHS
e3
Pb
DSLP Series - SOT23-6
Description
This new DSLP Series provides overvoltage protection for
applications such as HD-SDI, HD-CVBS, ADSL, ADSL2,
ADSL2+, VDSL2, Vplus (35b), and G.fast with minimal
effect on data signals. This silicon design innovation results
in a capacitive loading characteristic that is compatible with
these high bandwidth applications.
These components adopt the patent granted EpiSCR
silicon crowbar technology and industry popular cost
competitive SOT23-6 package with flow-through lead frame
design.
There are various VDRM options available in this series. This
technology provides a better surge capability than traditional
clamping silicon technology. This reduces the possibility
of field failures caused by A.C. power fault and multiple
transient surges or lightning without compromising the
signal integrity particularly at high data rate.
Agency Approvals
Agency
Agency File Number
E133083
Features & Benefits
Pinout Designation & Schematic Symbol
• Compatible with ADSL,
ADSL2+, VDSL2, VDSL2+
(35.328MHz, VDSL2 35b
profile) and G.fast (both
106MHz & 212MHz)
• Ultra low capacitance
characteristic provides
low insertion loss and less
distortion particularly in
higher data rate signals
TIP IN
6
5
1
TIP OUT
Bias+
• Balanced voltage
protection
• RoHS Compliant
• Flow-though pin
assignment and layout
ideal for high data rate
• Pb-free E3 means 2nd level
interconnect is Pb-free
and the terminal finish
material is tin(Sn) (IPC/
JEDEC J-STD-609A.01)
Bias-
2
3
• Superior surge capability
of of 30 A min, 35 A typ @
8/20µs, 15 A typ @
5/310 µs
4
RING IN
RING OUT
• Fast response time
• Wide variety VDRM options
for precise protection level
needs
Applicable Global Standards
• IEC 61000-4-5 2nd edition, 30 A min (tp = 8/20)
Electrical Characteristics between pin 1 and pin 3,Ta = 25°C
VDRM
IDRM=100nA
@
IR
Capacitance
f=1MHz,2V bias
@
VS@100V/µs
IH
IS
@VDRM
Part Number
Marking
V min
8
pA typ
300
V max
18
mA typ
40
mA min
pF typ
1.3
pF max
2. 5
2.5
D08
D12
D18
D24
D36
10
10
10
10
10
DSLP0080T023G6RP
DSLP0120T023G6RP
DSLP0180T023G6RP
DSLP0240T023G6RP
DSLP0360T023G6RP
12
300
22
40
1.3
18
300
28
40
1.3
2.5
24
300
34
40
1.3
2.5
36
300
48
40
1.3
2.5
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/16/18
DSLP Biased Series - SOT23-6
SIDACtor® ProtectionThyristors
Broadband Optimized™ Protection
Surge Ratings
V-I: Characteristics
IPP
8/20 1
5/310 1
Series
1.2/50 2
10/700 2
A min
30
A typ
35
A typ
G
15
Notes:
1 Current waveform in µs
2 Voltage waveform in µs
- Peak pulse current rating (IPP) is repetitive and guaranteed for the life of the product that
remains in thermal equilibrium.
- The component must be in thermal equilibrium at 25°C.
Typical capacitance against line voltage (without
external bias)
Capacitance vs.Voltage
2.5
2
2.0
1.8
1.6
1.4
1.2
1.0
0.8
1.5
Tip-Ring
1
0.5
0
0%
20%
% of Voltage to V
0.1
1
10
100
40% 60%
80% 100%
Line Voltage
DRM
Normalized Holding Current vs. CaseTemperature
NormalizedVS Change vs. JunctionTemperature
1.2
1.1
1.0
0.9
0.8
0.7
0.6
1.08
1.06
1.04
1.02
1.00
0.98
0.96
-50 -25
0
25 50 75 100 125 150
-50 -25
0
25 50 75
100 125 150
JunctionTemperature (T ) – °C
CaseTemperature ºC
J
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/16/18
DSLP Biased Series - SOT23-6
SIDACtor® ProtectionThyristors
Broadband Optimized™ Protection
Thermal Information
Parameter
Value
Unit
°C
Storage Temperature Range
-55 to 150
Maximum Junction Temperature
150
260
°C
Maximum Lead Temperature (Soldering 10s)
°C
Application example - G.fas Protection
G.fast has a targeted data rate of 1Gbps over 100 m of single twisted pair (24 AWG/0.5 mm) cable using DSL-like technology.
ThisTDD (Time Division Duplex) signaling is a major difference from the existing FDD (Frequency Division Duplex) DSL
signaling. G.fast bandwidth will extend up to 106 MHz (with the potential of going as high as 212 MHz) with the start
frequency ranging from 2.2 MHz up to 30 MHz in an effort to avoid interference with existing xDSL services. G.fast may also
employ “notching” where it suppresses carriers at specific individual frequencies to avoid clashing with local RF services.
Start at
2.2, 8, 12, 17 or 30 MHz
g.fast Line Driver
VDSL2
G.fast
dBm
TX
frequency
100MHz
SIDACtor
® Component
DSLP0xx0T023G6
T1
TIP
TIP OUT
6
5
1
TIP IN
Bias+
Bias-
2
3
RX
4
RING IN
RING OUT
RING
About G.fast
The G.fast amplitude is very low as compared to existing xDSL services and thus the varying voltage across the SIDACtor®
component is very low. This results in imperceptible capacitance variance of the over voltage protection (OVP) component;
therefore a bias voltage on pins 2 & 5 is not required in most applications, but pin 2 can be connected to the G.fast driver
ground reference to provide longitudinal protection along with the differential protection mode. Rate and reach testing has
shown an acceptable loss of less than 0.2dB with the DSLP0xx0T023G6RP component included at the tertiary position.
Additionally, the flow-through layout of this component reduces the impedance mismatching “stub-effect” caused by non-
”flow-through” PCB trace connections and provides for an easier PCB design. The small SOT23-6 footprint conserves valuable
PCB real-estate space requriements.
Since this interface is capacitively coupled, no fusing is required for power fault protection, however; selection of appropriately
voltage rated capacitors must be considered regarding lightning exposure risks. The coupling transformer should have an
isolation rating of at least 1.5kV 50/60Hz and consideration of its lightning response characteristics must also be considered.
The IPP 8/20 surge rating of this DSLP0xx0T023G6RP series is 30A minimally with a typical IPP rating of 35A based on this
waveshape. This should be sufficient for even the most severe exposure G.fast applications (including GR-1089 Issue 6
interbuilding requirements and ITU K20/21/45 Enhanced external line recommendations). The “Bias -” lead can be connected
to the line driver ground with the “Bias + ” lead left open so this solution provides both differential and common mode
protection. Both “Bias -” and “Bias +” leads can be left floating for differential only protection and finally for capacitance
variance sensitive applications, the “Bias -” and “Bias +” leads may have the appropriate polarity voltage (< VDRM) applied to
further minimize any negative capacitance effects.
The higher VDRM components in this DSLP series can be considered for ADSL, ADSL2, VDSL2, and VDSL2+ applications
where the signal levels are much higher than the G.fast signals. The low off-state capacitance (>2pF max) and the flow-
through compatible SOT23-6 footprint properties of this series is also beneficial for these other xDSL applications.
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/16/18
DSLP Biased Series - SOT23-6
SIDACtor® ProtectionThyristors
Broadband Optimized™ Protection
Soldering Parameters
Reflow Condition
Pb-Free assembly
150°C
-Temperature Min (Ts(min)
)
-Temperature Max (Ts(max)
)
Pre Heat
200°C
-Time (Min to Max) (ts)
60-180 secs.
Average ramp up rate (LiquidusTemp (TL)
to peak)
3°C/sec. Max.
TS(max) toTL - Ramp-up Rate
3°C/sec. Max.
+217°C
-Temperature (TL) (Liquidus)
Reflow
-Temperature (tL)
60-150 secs.
250(+0/-5)°C
PeakTemp (TP)
Time within 5°C of actual PeakTemp (tp)
20-40 secs.
Ramp-down Rate
6°C/sec. Max.
8 min. Max.
260°C
Time 25°C to PeakTemp (TP)
Do not exceed
Physical Specifications
High ReliabilityTest Specification
Lead Plating
MatteTin
Pre-condition
(HTRB/TC/ PCT/
H3TRB)
(1) Bake 24hrs @150°C
(2)168hrs @85% RH and 85°C
(3) IR reflow,3 reflows, peak temperature of 260°C
Lead Material
Lead Coplanarity
Copper Alloy
JESD 22-108
VCC bias= 80%VDRM &TA=150°C, 1008hrs
0.0004 inches (0.102mm)
HTRB
Subsitute Material Silicon
MIL-STD-883, Method 1010.8 Condition C
-65°C to150°C, 1000 cycles
Temperature Cycling
Pressure Cooker
Body Material
Flammability
Molded Compound
UL Recognized compound meeting
flammability rating V-0
JEDEC 22-A102
100%RH @121°C @15psi, 96hrs
JESD 22-A101
Vcc bias (pin1to pin3)=VDRM ,85%RH, 85°C , 1008
hours
Bias Humidity
(H3TRB)
Notes:
1. All dimensions are in millimeters.
2. Dimensions include solder plating.
3. Dimensions are exclusive of mold flash & metal burr.
4. All specifications comply to JEDEC MO-178
5. Blo is facing up for mold and facing down for trim/form, i.e. reverse trim/form.
6. Package surface matte tine
JESD 22-A111
260°C ,10 secs.
RSH
Packing Options
PackageType
Description
Quantity
SOT23-6
Tape and Reel
3000
Part Numbering
Part Marking
0xx 0 T023G 6 RP
DSLP
6
5
4
Reel Pack
Type
SIDACtor DSL Protector
Number of pins
Part Marking Code
Dxx
Nominal Working voltage:
Surge Ipp rating
PackageType
Construction variable:
0=single chip
1
2
3
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/16/18
DSLP Biased Series - SOT23-6
SIDACtor® ProtectionThyristors
Broadband Optimized™ Protection
Dimensions - SOT23-6
Inches
Millimeters
Min
Dimensions
Min
Max
0.057
0.006
0.051
0.020
0.008
0.118
0.118
0.069
0.037
0.075
0.023
Max
1.450
0.150
1.300
0.508
0.200
3.000
3.000
1.750
0.950
1.900
0.600
A
-
-
A1
-
-
A2
-
-
b
0.014
0.004
0.110
0.102
0.057
-
0.350
0.090
2.800
2.600
1.450
-
C
D
E
E1
e
e1
-
-
L (note 4 & 5)
N (note 6)
0.004
0.100
6
6
Recommended Solder Pad Layout
0°C
10°C
0°C
10°C
M
O
P
-
-
-
-
0.102
0.027
0.039
0.038
-
-
-
-
2.590
0.690
0.990
0.950
R
M
Notes:
1. Dimensioning and tolearances per ANSI 14.5M-1982.
2. Package conforms to EIAJ SC-74 (1992)
3. Dimensions D and E1 are exclusive of mold flash, protrusions, or gate burrs.
4. Foot lenth L measured at reference to seatng plane.
5. “L” is the length of flat foot surface for soldering to substrate.
6. “N” is the number of terminal positions.
P
7. Controlling dimension: MILLIMETER. Converted inch dimensions are not necessarily
R
exact.
Embossed CarrierTape & Reel Specification - SOT23-6
4.0mm
2.0mm
14.4mm
1.5mm
DIA. HOLE
1.75mm
ACCESS HOLE
C
8mm
13mm
L
4.0mm
SOT-23 (8mm POCKET PITCH)
60mm
GENERAL INFORMATION
180mm
1. 3000 PIECES PER REEL.
2. ORDER IN MULTIPLES OF FULL REELS ONLY.
3. MEETS EIA-481 REVISION "A" SPECIFICATIONS.
8.4mm
USER DIRECTION OF FEED
PIN 1
COVER TAPE
Disclaimer Notice - Information furnished is believed to be accurate and reliable. However, users should independently evaluate the suitability of and
test each product selected for their own applications. Littelfuse products are not designed for, and may not be used in, all applications.
Read complete Disclaimer Notice at www.littelfuse.com/disclaimer-electronics.
© 2016 Littelfuse, Inc.
Specifications are subject to change without notice.
Revised: 02/16/18
DSLP Biased Series - SOT23-6
相关型号：
©2020 ICPDF网 联系我们和版权申明