XP1042-QT_10 [MIMIX]
12.0-16.0 GHz Power Amplifier; 12.0-16.0 GHz功率放大器型号: | XP1042-QT_10 |
厂家: | MIMIX BROADBAND |
描述: | 12.0-16.0 GHz Power Amplifier |
文件: | 总6页 (文件大小:660K) |
中文: | 中文翻译 | 下载: | 下载PDF数据表文档文件 |
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
Features
21 dB Small Signal Gain
25 dBm P1dB Compression Point
38 dBm Output IP3 Linearity
17 dB Gain Control with Bias Adjust
3x3mm Standard QFN Package
100% RF Testing
Absolute Maximum Ratings1
General Description
The XP1042-QT is a packaged driver amplifier that
operates over the 12.0-16.0 GHz frequency band. The
device provides 21 dB gain and 38 dBm Output Third
Order Intercept Point (OIP3) across the band and is
offered in an industry standard, fully molded 3x3mm
QFN package. The device includes on-chip ESD
protection structures and DC by-pass capacitors to
ease the implementation and volume assembly of the
packaged part. The device is manufactured in 0.5um
GaAs PHEMT device technology with BCB wafer
coating to enhance ruggedness and repeatability of
performance.The XP1042-QT is well suited for
Point-to-Point Radio, LMDS, SATCOM and VSAT
applications.
Supply Voltage (Vd1,2,3)
Supply Current (Id1,2,3)
+8.0V
550 mA
-2.4V
Gate Bias Voltage (Vg1,2,3)
Max Power Dissipation (Pdiss)
RF Input Power
Operating Temperature (Ta)
Storage Temperature (Tstg)
Channel Temperature (Tch)2
ESD Min. - Machine Model (MM)
2.8W
15 dBm
-55 to +85 ºC
-65 to +165 ºC
150 ºC
Class A
ESD Min. - Human Body Model (HBM) Class 1A
MSL Level MSL3
(1) Operation of this device above any one of these parameters
may cause permanent damage.
(2) Channel temperature directly affects a device’s MTTF.
Channel temperature should be kept as low as possible to
maximize lifetime
Electrical Characteristics (AmbientTemperatureT = 25 oC)
Parameter
Frequency Range (f)
Units
GHz
dB
dB
dB
dB
dB
dB
dBm
VDC
VDC
mA
mA
mA
Min.
12.0
19.0
Typ.
-
Max.
16.0
Small Signal Gain (S21)
Input Return Loss (S11)
Output Return Loss (S22)
Reverse Isolation (S12)
NF at Max Gain
21.0
12.0
10.0
50.0
6.0
25.0
38.0
5
-1
75
75
150
8.0
P1dB
OIP3 at Pout = 8 dBm per Tone
Drain Bias Voltage (Vd1,2,3)
Gate Bias Voltage (Vg1,2,3)
Supply Current (Id1)
Supply Current (Id2)
Supply Current (Id3)
36.0
-2
125
125
250
Page 1 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
Power Amplifier Measurements
XP1042-QT: S-parameters (dB) vs. Freq (GHz),
VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
25
20
15
10
5
S21
S11
S22
0
-5
-10
-15
-20
10
11
12
13
14
15
16
17
18
Freq (GHz)
XP1042-QT: Power Out (dBm) vs. Power In (dBm),
VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
30
25
20
15
10
5
12.5 GHz
13 GHz
13.5 GHz
14 GHz
14.5 GHz
15 GHz
15.5 GHz
-15
-10
-5
Power In (dBm)
0
5
10
XP1042-QT: C/I3 (dBc) vs. Output Tone Power (per tone) dBm
10MHz tone separation VDD=5V, ID1=125mA, ID2=125mA, ID3=250mA
80
70
60
50
12.5 GHz
40
13 GHz
13.5 GHz
30
14 GHz
14.5 GHz
20
15 GHz
15.5 GHz
10
0
6
8
10
12
14
16
18
20
Output tone level per tone (dBm)
Page 2 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
MTTF
These numbers were calculated based on accelerated life test information and thermal model analysis received from
the fabricating foundry.
XP1042-QT-0G00: MTTF hours vs Package Base Temperature
Vd1,2,3=5.0V;Id1=125mA,Id2=125mA,Id3=250mA
1.E+14
1.E+12
1.E+10
1.E+08
1.E+06
1.E+04
1.E+02
1.E+00
20
30
40
50
60
70
80
90
100
110
120
Package Base Temp (oC)
XP1042-QT-0G00: Tch(max) vs Package Base Temperature
Vd1,2,3=5.0V;Id1=125mA,Id2=125mA,Id3=250mA
200
180
160
140
120
100
80
60
40
20
0
20
30
40
50
60
70
80
90
100
110
120
Package Base Temp (oC)
XP1080-QK-0N00: Operating Power De-rating Curve (continuous)
Vd1,2,3=5V,Id1=125mA,Id2=125mA,Id3=250mA
3
2.5
2
1.5
1
0.5
0
25
50
75
100
125
150
175
Package Base Temp (oC)
Page 3 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
Package Dimensions / Layout
Functional Block Diagram
Pin Designations
nc
Vd1 Vd2 Vd3
Pin Number Pin Name Pin Function Nominal Value
1-2
3
4
5
6
nc
RF In
nc
Vg1
Vg2
Vg3
nc
RF Out
nc
Vd3
Vd2
Vd1
nc
Not Connected
RF Input
Not Connected
Gate 1 Bias
Gate 2 Bias
Gate 3 Bias
GND
GND
~ -1.0V
~ -0.8V
~ -1.0V
GND
7
8-9
10
11-12
13
14
15
16
Not Connected
RF Output
nc
nc
1
2
3
4
12
11
10
9
nc
nc
Not Connected
Drain 3 Bias
Drain 2 Bias
Drain 1 Bias
Not Connected
GND
5.0V, 250 mA
5.0V, 125 mA
5.0V, 125 mA
GND
RF In
nc
RF Out
nc
Vg1 Vg2 Vg3
nc
Page 4 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
App Note [1] Biasing - As shown in the Pin Designations table, the device is operated by biasing VD1,2,3 at 5.0V with 125, 125, 250 mA respectively.
It is recommended to use active bias to keep the currents constant in order to maintain the best performance over temperature. Depending on the
supply voltage available and the power dissipation constraints, the bias circuit may be a single transistor or a low power operational amplifier, with
a low value resistor in series with the drain supply used to sense the current.The gate of the pHEMT is controlled to maintain correct drain current
and thus drain voltage.The typical gate voltage needed to do this is -1.0V. Make sure to sequence the applied voltage to ensure negative gate bias
is available before applying the positive drain supply.
App Note [2] Board Layout - As shown in the board layout, it is recommended to provide 100pF decoupling caps as close to the bias pins as
possible, with additional 10µF decoupling caps.
Recommended Layout
Page 5 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
12.0-16.0 GHz Power Amplifier
QFN, 3x3mm
February 2010 - Rev 22-Feb-10
P1042-QT
Handling and Assembly Information
CAUTION! - Mimix Broadband MMIC Products contain gallium arsenide (GaAs) which can be hazardous to the human body and the
environment. For safety, observe the following procedures:
• Do not ingest.
• Do not alter the form of this product into a gas, powder, or liquid through burning, crushing, or chemical processing as these by-
products are dangerous to the human body if inhaled, ingested, or swallowed.
• Observe government laws and company regulations when discarding this product.This product must be discarded in accordance with
methods specified by applicable hazardous waste procedures.
Life Support Policy - Mimix Broadband's products are not authorized for use as critical components in life support devices or systems
without the express written approval of the President and General Counsel of Mimix Broadband. As used herein: (1) Life support devices or
systems are devices or systems which, (a) are intended for surgical implant into the body, or (b) support or sustain life, and whose failure to
perform when properly used in accordance with instructions for use provided in the labeling, can be reasonably expected to result in a
significant injury to the user. (2) A critical component is any component of a life support device or system whose failure to perform can be
reasonably expected to cause the failure of the life support device or system, or to affect its safety or effectiveness.
Package Attachment - This packaged product from Mimix Broadband is provided as a rugged surface mount package compatible with high
volume solder installation. Vacuum tools or other suitable pick and place equipment may be used to pick and place this part. Care should be
taken to ensure that there are no voids or gaps in the solder connection so that good RF, DC and ground connections are maintained. Voids
or gaps can eventually lead not only to RF performance degradation, but reduced reliability and life of the product due to thermal stress.
Typical Reflow Profiles
Reflow Profile
SnPb
Pb Free
Ramp Up Rate
3-4 ºC/sec
60-120 sec @ 140-160 ºC
60-150 sec
240 ºC
3-4 ºC/sec
Activation Time and Temperature
Time Above Melting Point
Max Peak Temperature
Time Within 5 ºC of Peak
Ramp Down Rate
60-180 sec @ 170-200 ºC
60-150 sec
265 ºC
10-20 sec
10-20 sec
4-6 ºC/sec
4-6 ºC/sec
Factory Automation and Identification
Mimix
Designator
Package
Type
Number of
leads offered
W Tape
Width
P1 Component P0 Hole
Reel
Diameter
Units
per Reel
Pitch
Pitch
-QT
QFN (3x3mm)
12mm
16
8mm
4mm
329mm (13in)
2000
Component Orientation:
Parts are to be oriented with the PIN 1 closest to the tape's round sprocket holes on the tape’s trailing edge.
Note: Tape and Reel packaging is ordered with a -0G0T suffix. Package is available in 500 unit reels through designated sales channels.
Minimum order quantities should be discussed with your local sales representative.
Mimix Lead-Free RoHS Compliant Program - Mimix has an active program in place to meet customer and governmental requirements for
eliminating lead (Pb) and other environmentally hazardous materials from our products. All Mimix RoHS compliant components are form, fit
and functional replacements for their non-RoHS equivalents. Lead plating of our RoHS compliant parts is 100% matte tin (Sn) over copper
alloy and is backwards compatible with current standard SnPb low-temperature reflow processes as well as higher temperature (260°C
reflow) “Pb Free” processes.
Ordering Information
Part Number for Ordering
XP1042-QT-0G00
Description
Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in bulk quantity
Matte Tin plated RoHS compliant 3x3 16L QFN surface mount package in tape and reel
XP1042-QT evaluation board
XP1042-QT-0G0T
XP1042-QT-EV1
Caution: ESD Sensitive
Appropriate precautions in handling, packaging
and testing devices must be observed.
Proper ESD procedures should be followed when handling this device.
Page 6 of 6
Mimix Broadband, Inc., 10795 Rockley Rd., Houston,Texas 77099
Tel: 281.988.4600 Fax: 281.988.4615 mimixbroadband.com
Characteristic Data and Specifications are subject to change without notice. ©2010 Mimix Broadband, Inc.
Export of this item may require appropriate export licensing from the U.S. Government. In purchasing these parts, U.S. Domestic customers accept
their obligation to be compliant with U.S. Export Laws.
相关型号:
©2020 ICPDF网 联系我们和版权申明