40DR-R1R/Q [MSYSTEM]
Digital Panel Meters 40 Series;
| 型号： | 40DR-R1R/Q |
| 厂家： | 
M-SYSTEM |
| 描述： | Digital Panel Meters 40 Series |
| 文件： | 总6页 (文件大小：201K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
MODEL: 40DR
Digital Panel Meters 40 Series
SPECIFICATIONS OF OPTION: Q (multiple selections)
COATING (For the detail, refer to M-System's web site.)
Moving parts and indicators are not coated.
/C01: Silicone coating
RTD INPUT DIGITAL PANEL METER
(4 digits, process meter)
/C02: Polyurethane coating
Functions & Features
/C03: Rubber coating
• 4 digit (±9999) panel meter
• HOLD functions
EX-FACTORY SETTING
/SET: Preset according to the Ordering Information Sheet
(No. ESU-9533)
• High visible, 0.8" (20.3mm) high and bright LED
96 (3.78)
GENERAL SPECIFICATIONS
Construction: Panel flush mounting
48
(1.89)
Connection: M3 screw terminals (torque 0.6 N·m)
Solderless terminal: Refer to the drawing at the end of the
section.
96 (3.78)
Recommended manufacturer: Japan Solderless Terminal
MFG.Co.Ltd, Nichifu Co.,ltd
mm (inch)
Applicable wire size: 0.25 to 1.65 mm
2
(AWG 22 to 16)
Screw terminal: Nickel-plated steel
MODEL: 40DR–R1–[1][2]
Housing material: Flame-resistant resin (gray)
Isolation: Input to power
A/D conversion: Σ – Δ
ORDERING INFORMATION
• Code number: 40DR–R1–[1][2]
Specify a code from below for each of [1] and [2].
(e.g. 40DR-R1-R/Q)
Sampling rate: 10 times/sec. (100 msec.)
Averaging: None or moving average
Setting: (Front button)
• Specify the specification for option code /Q
(e.g. /C01/SET)
• Temperature unit
• Moving average
• Brightness
• Others
INPUT
■Recommended solderless terminal
R1: Pt 100 (JIS'97, IEC)
3.3 (.13) max
(Usable range -200 to +850°C, -328 to +1562°F)
Pt 100 (JIS'89)
(Usable range -200 to +650°C, -328 to +1202°F)
mm (inch)
[1] POWER INPUT
AC Power
K3: 100 – 120V AC
DISPLAY
(Operational voltage range 85 - 132 V, 47 - 66 Hz)
L3: 200 – 240V AC
Display: 4 digits of 20.3 mm (0.8 inch) height, 7-segment,
red LED
(Operational voltage range 170 - 264 V, 47 - 66 Hz)
DC Power
Display range: -9999 to 9999
Decimal point position: 10–1 or none
Zero indication: Higher-digit zeros are suppressed.
Over-range indication:
R: 24 V DC
(Operational voltage range 24 V ±20 %, ripple 10 %p-p max.)
'S.ERR' blinks surpassing the permissible range.
'B.ERR' blinks at burnout.
[2] OPTIONS
Engineering unit indication: Sticker label attached
DC, AC, mV, V, kV, μA, mA, A, kA, mW, W,
kW, var, kvar, Mvar, VA, Hz, Ω, kΩ, MΩ,
cm, mm, m, m/sec, mm/min, cm/min, m/min,
blank: none
/Q: With options (specify the specification)
m/h, m/s
2
, inch, ℓ, ℓ/s, ℓ/min, ℓ/h, m
3
, m /sec,
3
m3/min, m3/h, Nm3/h, N·m, N/m2, g, kg, kg/h,
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 1/6
https://www.m-system.co.jp/
MODEL: 40DR
N, kN, Pa, kPa, MPa, t, t/h, ℃, °F, %RH, J,
kJ, MJ, rpm, sec, min, pH, %, ppm, etc.
INPUT SPECIFICATIONS
■ RTD (3-wire)
Maximum leadwire resistance: 10 Ω per wire
Sensing current: Approx. 0.5 mA
Usable range (conformance range):
Pt100 (JIS’97, IEC) -200 to +850℃ or -328 to +1562°F
Pt100 (JIS’89) -200 to +650℃ or -328 to +1202°F
Operational range: -230 to +880℃ or -382 to +1616°F
■ Hold Input: Dry contact input
Detecting level: ≤ 1.5 V
Sensing: Approx. 5 V DC, 1 mA
INSTALLATION
Power consumption
•AC:
Approx. 1.3 VA for 100 – 120 V
Approx. 1.2 VA for 200 – 240 V
•DC: Approx. 0.5 W
Operating temperature: -10 to +55°C (14 to 131°F)
Operating humidity: 30 to 90 %RH (non-condensing)
Mounting: Panel flush mounting
Weight: 160 g (0.35 lb)
PERFORMANCE
Accuracy
-200 – +200°C: ±0.2°C rdg ±1 digit
200 – 850°C: ±0.6°C rdg ±1 digit
-328 – +1562°F: ±1°F rdg ±1 digit
Temp. coefficient: ±0.1 ℃/℃
Line voltage effect: ±1 digit over voltage range
Insulation resistance: ≥ 100 MΩ with 500 V DC
Dielectric strength: 1500 V AC @1 minute (input to power to
ground)
STANDARDS & APPROVALS
EU conformity:
EMC Directive
EMI EN 61000-6-4
EMS EN 61000-6-2
Low Voltage Directive
EN 61010-1
Installation Category II
Pollution Degree 2
Input to power: Reinforced insulation (300 V)
RoHS Directive
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 2/6
https://www.m-system.co.jp/
MODEL: 40DR
DISPLAY HOLD COMMAND
Displayed value is held with an external HOLD command input. Connect the contacts across HOLD to COM.
(a)
(c)
5V–CMOS, TTL
Photo-Coupler
HOLD
H
HOLD
H
L
L
5
6
HOLD
COM
5
6
HOLD
COM
Photo-Coupler
Twisted pair cable
Twisted pair cable
(b)
Transistor
(d)
Relay
HOLD
H
HOLD
H
L
L
5
6
HOLD
COM
5
6
HOLD
COM
Relay
Twisted pair cable
Twisted pair cable
EXTERNAL VIEW
(1) Front Panel
(3) 4-digit Display
(4) Polarity Indicator
(8) Up Button
(5) Disp/ Button
(6) Scale/ Button
(2) Sticker Label
(7) Shift Button
■ COMPONENT IDENTIFICATION
No.
(1)
(2)
(3)
(4)
COMPONENT
Front panel
FUNCTIONS
Removed at conguration.
Engineering unit label position
Sticker label
4-digit display
Polarity indicator
4-digit LED display. Range: 0 to 9999 (not including decimal point)
Turns on when negative value is displayed
Used to move on to the display setting modes; or to shift through setting items in each
setting mode.
(5)
(6)
Disp/ button
Scale/ button
Used to move on to the zero & span adjustment modes; or to shift through setting items in
each setting mode.
Used to move on to the setting standby status and shift through display digits in each set-
ting item.
(7)
(8)
Shift button
Up button
Used to select setting value.
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 3/6
https://www.m-system.co.jp/
MODEL: 40DR
PARAMETER LIST
■ ZERO & SPAN ADJUSTMENTS
PARAMETER
DISPLAY
–
FUNCTION
Adjustment value for -200°C
DEFAULT VALUE
Zero adjustment
To distinguish from span adjustment, the "rst decimal point is blink-
ing
Span adjustment
Temperature unit
–
Adjustment value for 850°C
Display in Celsius
Display in Fahrenheit (Temperature range: -328 to +1562°F)*1
Decimal Point Position
10-1 or none
Decimal point position for celsius
*1. For Fahrenheit, the value is rounded to integer. Decimal point position setting is not available.
■ DISPLAY SETTING MODE
PARAMETER
DISPLAY
FUNCTION
DEFAULT VALUE
Moving Average
No moving averaging
Moving average with 2 samples
Moving average with 4 samples
Moving average with 8 samples
Moving average with 16 samples
Brightness level 1 (dark)
Brightness
Brightness level 2
Brightness level 3
Brightness level 4
Brightness level 5 (bright)
Non-initialization
Initialization
Initialize settings (change to factory settings) *1
Version Indication
−
Version number, indication only
−
*1. While “
” is shown, pressing Disp/ button or Scale/ button initializes settings.
Activating “initialization”, user’s speci"ed parameters will be deleted and overwritten with the factory default values. Notice that after this,
Ex-factory settings will be irrecoverable.
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 4/6
https://www.m-system.co.jp/
MODEL: 40DR
EXTERNAL DIMENSIONS & TERMINAL ASSIGNMENTS unit: mm (inch)
■ TOP VIEW
92 (3.62)
■ FRONT VIEW
■ SIDE VIEW
103 (4.06)
96 (3.78)
96 (3.78)
85 (3.35)
11
(.43)
12 (.47)
■ REAR VIEW
10–M3 SCREW
TERMINALS
6.4 (.25)
1
2
3
4
5
6
7
8
9
10
MOUNTING REQUIREMENTS unit: mm
92 +– 00.8
min. 120
Panel thickness: 1.6 to 8.0 mm
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 5/6
https://www.m-system.co.jp/
MODEL: 40DR
SCHEMATIC CIRCUITRY & CONNECTION DIAGRAM
RTD
U(+)
V(–)
A
B
B
1
2
3
5
6
9
10
4
POWER
A/D
Converter
Digital
Computation
HOLD
COM
7
8
Display /
Setting
Specifications are subject to change without notice.
40DR SPECIFICATIONS
ES-9533 Rev.10 Page 6/6
https://www.m-system.co.jp/
相关型号：
©2020 ICPDF网 联系我们和版权申明