NSVS1127 [NJRC]
SAW Filter, 1 Function(s), 915MHz,;
| 型号： | NSVS1127 |
| 厂家： | 
NEW JAPAN RADIO |
| 描述： | SAW Filter, 1 Function(s), 915MHz, LTE |
| 文件： | 总4页 (文件大小：204K) |
| 中文： | 中文翻译 | 下载： | 下载PDF数据表文档文件 |
NSVS1127 Apr-2013
NewJRC SAW FILTER
NSVS1127
Application
915.0MHz SAW filter
Electrical Specification: (Table 1)
The device characteristics are measured in the circuit shown in Fig.1.
Table 1. Electrical Specifications
Item
Spec.
-
Typical
50Ω
915MHz
Condition
-
Input and Output Impedance
Nominal Center Frequency (f0)
Insertion Loss
-
-
3.4dB max.
3.6dB max.
1.5dB max.
1.7dB max.
2.5 max.
38dB min.
35dB min.
17dB min.
20dB min.
38dB min.
-20~+70ºC
-40~+85ºC
-20~+70ºC
-40~+85ºC
902.0~928.0MHz
2.8dB
0.8dB
Response Variation
902.0~928.0MHz
(
Input and Output VSWR
Out of Band Rejection
(Relative toThrough Level)
902.0~928.0MHz
DC~800.0MHz
1.8
43dB
40dB
30dB
28dB
43dB
27dB
800.0~845.0MHz
845.0~880.0MHz
947.0~992.0MHz
992.0~1020.0MHz
-40~+85ºC
1020.0~1200.0MHz 20dB min.
(Operating Temperature Range : -40~+85ºC)
Maximum Rating: (Table 2)
Table2. Maximum Ratings
Item
Rating
Maximum Input Power
Maximum DC Voltage
Operating Temperature Range
Storage Temperature
+10dBm
7.5V
-40~+85ºC
-40~+85ºC
Mechanical Specifications: (Fig.2)
Package is designed as small as 3.0x3.0x1.15[mm3] for SMD (Surface Mount Device) type.
Notice:
This part is electrostatic discharge sensitive and may be damaged by improper handling.
http://www.njr.co.jp/products/device/index.html
http://www.njr.com/products/device/index.html
(Japanese)
(English)
NSVS1127 Apr-2013
1
6
2 SAW5
IN
3
4
OUT
50Ω
50Ω
Fig.1 Measuring circuit
3. 0±0. 15
(b)
(a)
221
(c)
(1)
KA
(2)
Marking
(1) Lot Number
(a) Year
(b) Month
(0. 6)
*Oct.---
X
Y
Z
Nov.---
Dec.---
4
5
3
(c) Date
1-9---
0
1
2
10-19---
20-31---
2
1
(2) Part Number Mark
(1. 80)
6
Pin no.
Connection
GND
1
2
3
4
5
6
(0. 75)
[4x]
(0. 45)
IN/OUT
GND
Fig.2 Package dimensions (in mm)
3.8
GND
OUT/IN
GND
2.2
1.15
1.15
Fig.3 Desirable land area (in mm)
NSVS1127 Apr-2013
Notice
1. Use this component within operating temperature range. It might not be
satisfied with electrical specification without operating temperature range.
When it is used less than -40ºC or more than +85ºC, it might be a cause of
degradation or destruction of the component. Even if it endures during a short
time, it causes degradation of qualification.
2. When soldering iron is used, solder with the temperature at the tip of soldering
iron: 350ºC max., the time of soldering: 10 seconds max., the power of
soldering iron: 30W max..
3. Notice that the allowed time of soldering with soldering iron is accumulated
time, when soldering is repeated.
4. As rapid temperature change for cleaning after reflow soldering might be a
cause of destruction clean this component after confirming that temperature of
this component goes down to room temperature.
5. Confirm that there are not any influence for qualification to this component in
mounting on PCB when this component is cleaned.
6. As it might be a cause of degradation of destruction to apply static electricity to
this component, do not apply static electricity or excessive voltage while
assembling and measuring. And do not transport this component with bare
hand.
7. As it might be a cause of degradation or destruction to apply D.C. voltage
between each terminal, apply D.C. voltage 7.5V max. in actual circuit.
Note
1. This specification specifies the quality of this component as a single unit. Make
sure that this component is evaluated and confirmed against this specification
when it is mounted to your products.
2. The information contained herein may be changed without prior notice. It is
therefore advisable to contact New Japan Radio Company before proceeding
with the design of equipment incorporating this product.
3. The products are designed to be used with ordinary electronic equipment
(data and communications equipment, office equipment, audio-video
equipment, measuring instruments, etc). New Japan Radio Company does
not assume any liability for the case using the products with the application
required high reliability or safety extremely (such as space equipment,
sea-bottom equipment, medical equipment etc). When intending to use any
our product please contact our sales representatives in advance.
***NSVS1127 Apr. 2013
NewJRC 915MHz SAW FILTER
NSVS1127
FREQUENCY CHARACTERISTICS
S21
1
0
0
1 : 902 [MHz] 2.68 [dB]
2
2
2 : 928 [MHz] 2.62 [dB]
3 : 880 [MHz] 37 [dB]
4 : 947 [MHz] 28.92 [dB]
10
20
30
40
50
2
1
4
6
4
4
8
3
10
CH1 : center 915 span 200
3
CH2 : center 915 span 200
S11
S22
S22
1
1
2
2
3
3
4
4
S11
11
11
9
3
4
3
4 N
9
7
5
3
1
7
5
3
1
1
1
2
2
815
1015
815
1015
Frequency [MHz]
Frequency [MHz]
S21
0
20
40
60
80
100
0
3000
Frequency [MHz]
相关型号：
©2020 ICPDF网 联系我们和版权申明